HMG-1648P HMG-1648EP. Industrial 16 x 10/100Base-T(X) + 4 x 100/1000Base SFP Gigabit Managed Ethernet Switch User s Manual (CLI Command)

Size: px
Start display at page:

Download "HMG-1648P HMG-1648EP. Industrial 16 x 10/100Base-T(X) + 4 x 100/1000Base SFP Gigabit Managed Ethernet Switch User s Manual (CLI Command)"

Transcription

1 HMG-1648P HMG-1648EP Industrial 16 x 10/100Base-T(X) + 4 x 100/1000Base SFP Gigabit Managed Ethernet Switch User s Manual (CLI Command) V

2 Husky Series Industrial Ethernet Switch Solutions HMG-1648P & HMG-1648EP Industrial Gigabit Managed Ethernet Switch User s Manual (CLI Command) Copyright Notice Copyright 2017 Ethernet Direct Corp. All rights reserved. Reproduction in any form or by any means without Ethernet Direct prior written permission is prohibited.

3 Table of Contents Chapter 1 Introduction to CLI About CLI (Console Access) How to Access CLI CLI Modes Quick Keys Command Syntax...2 Chapter 2 Basic Configuration Configuring IPv4 Address Enter Config Interface Mode Save Configurations Restart the Device Load Factory Defaults Check IP address Show System and Software Information Show SFP Information Show Running Configurations Show History Help Logout...5 Chapter 3 Commands in User Mode > clear ip arp > clear lldp statistics > clear statistics > enable > exit > help > ping ip > ping ipv > traceroute > show commands...3 Chapter 4 Commands in EXEC Mode # clear access management statistics # clear access-list ace statistics # clear dot1x statistics # clear erps # clear ip arp # clear ip dhcp detailed statistics # clear ip dhcp server binding <ip> # clear ip dhcp server binding { automatic manual expired } # clear ip dhcp server statistics # clear ip dhcp relay statistics # clear ip dhcp snooping statistics # clear ip igmp snooping # clear ip statistics # clear ipv6 mld snooping # clear ipv6 neighbors # clear ipv6 statistics # clear lacp statistics...3

4 4-18 # clear lldp statistics # clear logging # clear mac address-table # clear mep # clear mvr # clear spanning-tree # clear statistics erminal # copy # delete # dir # disable & # enable # dot1x # erps # firmware swap # firmware upgrade # ip dhcp retry interface vlan # more # ping ip # ping ipv # ptp # reload warm # reload default # send # terminal editing # terminal exec-timeout # terminal history size # terminal length # terminal width # traceroute ip # no port-security shutdown # show interface ( <port_type> [ <v_port_type_list> ] ) utp-cable-diagnostic # show command...12 Chapter 5 Commands in Config Mode (config)# aaa authentication login (config)# access management (config)# access-list (config)# access-list ace (config)# access-list ace update (config)# access-list rate-limiter (config)# access-list action (config)# access-list logging (config)# access-list mirror (config)# access-list policy (config)# access-list port-state (config)# access-list rate-limiter (config)# access-list shutdown (config)# access-list shutdown (config)# aggregation (config)# aggregation mode (config)# aggregation group (config)# banner...6

5 5-5.1 (config)# banner [ motd ] <banner> (config)# banner exec <banner> (config)# banner login <banner> (config)# clock (config)# clock summer-time <word16> date (config)# clock summer-time <word16> recurring (config)# clock timezone (config)# default access-list rate-limiter (config)# dot1x (config)# dot1x system-auth-control (config)# dot1x re-authentication (config)# dot1x authentication timer re-authenticate (config)# dot1x timeout tx-period (config)# dot1x authentication timer inactivity (config)# dot1x timeout quiet-period (config)# dot1x feature (config)# dot1x guest-vlan (config)# dot1x guest-vlan supplicant (config)# dot1x max-requth-req (config)# dot1x port-control (config)# dot1x guest-vlan (config)# dot1x radius-qos (config)# dot1x radius-vlan (config)# dot1x re-authenticate (config)# duplex (config)# enable (config)# enable password (config)# enable password level (config)# enable secret (config)# erps (config)# erps <group> guard <guard_time_ms> (config)# erps <group> holdoff <holdoff_time_ms> (config)# erps <group> major port0 interface port1 interface <port_type> <port1> [ interconnect ] (config)# erps <group> mep port0 sf <p0_sf> aps <p0_aps> port1 sf <p1_sf> aps <p1_aps> (config)# erps <group> revertive <wtr_time_minutes> (config)# erps <group> rpl { owner neighbor } { port0 port1 } (config)# erps <group> sub port0 interface <port_type> <port0> { { port1 interface <port_type> <port1> } { interconnect <major_ring_id> [ virtual-channel ] } } (config)# erps <group> topology-change propagate (config)# erps <group> version { 1 2 } (config)# erps <group> vlan { none [ add remove ] <vlans> } (config-if)# excessive-restart (config-if)# flowcontrol { on off } (config)# green-ethernet (config)# green-ethernet led interval (config)# green-ethernet led on-event (config)# green-ethernet eee optimize-for-power (config-if)# green-ethernet eee (config-if)# green-ethernet urgent-queues (config-if)# green-ethernet energy-detect (config-if)# green-ethernet short-reach (config)# gvrp...20

6 (config)# gvrp (config)# gvrp max-vlans (config)# gvrp time (config-if)# gvrp (config)# hostname (config)# interface (config)# interface ( <port_type> [ <plist> ] ) (config)# interface vlan (config)# ip (config)# ip arp inspection (config)# ip arp inspection entry interface (config)# ip arp inspection translate (config)# ip arp inspection vlan (config)# ip arp inspection vlan <in_vlan_list> logging (config)# ip dhcp relay (config)# ip dhcp relay information option (config)# ip dhcp relay information policy {drop keep replace} (config)# ip dhcp snooping (config)# ip dns proxy (config)# ip helper-address (config)# ip http secure-server (config)# ip http secure-redirect (config)# ip igmp host-proxy (config)# ip igmp snooping (config)# ip igmp snooping vlan (config)# ip igmp ssm-range (config)# ip igmp unknown-flooding (config)# ip name-server (config)# ip route (config)# ip routing (config)# ip source binding interface (config)# ip ssh (config)# ip verify source (config)# ip verify source translate (config-if)# ip arp inspection check-vlan (config-if)# ip arp inspection logging (config-if)# ip arp inspection trust (config-if)# ip dhcp snooping trust (config-if)# ip igmp snooping filter (config-if)# ip igmp snooping immediate-leave (config-if)# ip igmp snooping max-groups (config-if)# ip igmp snooping mrouter (config-if)# ip verify source (config-if)# ip verify source limit (config-if-vlan)# ip address (config-if-vlan)# ip igmp snooping (config-if-vlan)# ip igmp snooping compatibility (config-if-vlan)# ip igmp snooping last-member-query-interval (config-if-vlan)# ip igmp snooping priority (config-if-vlan)# ip igmp snooping querier address (config-if-vlan)# ip igmp snooping querier election (config-if-vlan)# ip igmp snooping query-interval...36

7 (config-if-vlan)# ip igmp snooping query-max-response-time (config-if-vlan)# ip igmp snooping robustness-variable (config-if-vlan)# ip igmp snooping unsolicited-report-interval (config-if-vlan)# ipv6 address (config-if-vlan)# ipv6 mld snooping (config-if-vlan)# ipv6 mld snooping compatibility (config-if-vlan)# ipv6 mld snooping last-member-query-interval (config-if-vlan)# ipv6 mld snooping priority <cos_priority> (config-if-vlan)# ipv6 mld snooping querier election (config-if-vlan)# ipv6 mld snooping query-interval <ipmc_qi> (config-if-vlan)# ipv6 mld snooping query-max-response-time <ipmc_qri> (config-if-vlan)# ipv6 mld snooping robustness-variable <ipmc_rv> (config-if-vlan)# ipv6 mld snooping unsolicited-report-interval <ipmc_uri> (config)# ipmc (config)# ipmc profile (config)# ipmc profile <profile_name> (config)# ipmc range (config-ipmc-profile)# default range (config-ipmc-profile)# default range (config-ipmc-profile)# range (config)# ipv6 mld host-proxy (config)# ipv6 mld host-proxy (config)# ipv6 mld host-proxy leave-proxy (config)# ipv6 mld snooping (config)# ipv6 mld snooping vlan (config)# ipv6 mld ssm-range (config)# ipv6 mld unknown-flooding (config)# ipv6 route (config-if)# ipv6 mld snooping filter (config-if)# ipv6 mld snooping immediate-leave (config-if)# ipv6 mld snooping max-groups (config-if)# ipv6 mld snooping mrouter config-if)# l2cp (config)# lacp (config)# lacp system-priority (config-if)# lacp (config-if)# lacp key (config-if)# lacp port-priority <v_1_to_65535> (config-if)# lacp role { active passive } (config-if)# lacp timeout { fast slow } (config)# line (config)# line (config-line)# do (config-line)# editing (config-line)# end (config-line)# exec-banner (config-line)# exec-timeout (config-line)# exit (config-line)# help (config-line)# history size (config-line)# length (config-line)# location...52

8 (config-line)# motd-banner (config-line)# privilege level (config-line)# width (config)# lldp (config)# lldp holdtime (config)# lldp reinit (config)# lldp timer (config)# lldp transmission-delay (config)# lldp med datum (config)# lldp med fast (config)# lldp med location-tlv altitude (config)# lldp med location-tlv civic-addr (config)# lldp med location-tlv elin-addr (config)# lldp med location-tlv latitude (config)# lldp med location-tlv longitude (config)# lldp med media-vlan-policy (config-if)# lldp cdp-aware (config-if)# lldp med media-vlan policy-list (config-if)# lldp med transmit-tlv (config-if)# lldp receive (config-if)# lldp tlv-select (config-if)# lldp transmit (config)# logging (config)# logging on (config)# logging host (config)# logging level (config)# loop-protect (config)# loop-protect (config)# loop-protect shutdown-time (config)# loop-protect transmit-time (config-if)# loop-protect (config-if)# loop-protect action (config-if)# loop-protect tx-mode (config)# mac (config)# mac address-table aging-time (config)# mac address-table static (config-if)# mac address-table learning (config-if)# media-type (config-if)# mtu (config)# mep (config)# mep <inst> (config)# mep <inst> ais (config)# mep <inst> aps (config)# mep <inst> cc (config)# mep <inst> client domain (config)# mep <inst> client flow (config)# mep <inst> dm (config)# mep <inst> dm ns (config)# mep <inst> dm overflow-reset (config)# mep <inst> dm proprietary (config)# mep <inst> dm syncronized (config)# mep <inst> lb...70

9 (config)# mep <inst> lck (config)# mep <inst> level (config)# mep <inst> lm (config)# mep <inst> lt (config)# mep <inst> meg-id (config)# mep <inst> peer-mep-id (config)# mep <inst> performance-monitoring (config)# mep <inst> tst (config)# mep <inst> tst rx (config)# mep <inst> tst tx (config)# mep <inst> vid (config)# mep <inst> voe (config)# monitor (config)# monitor destination interface (config)# monitor source (config)# mvr (config)# mvr (config)# mvr name <mvr_name> channel (config)# mvr name <mvr_name> frame priority (config)# mvr name <mvr_name> frame tagged (config)# mvr name <mvr_name> igmp-address (config)# mvr name <mvr_name> last-member-query-interval (config)# mvr name <mvr_name> mode (config)# mvr vlan <v_vlan_list> (config)# mvr vlan <v_vlan_list> channel (config)# mvr vlan <v_vlan_list> frame priority (config)# mvr vlan <v_vlan_list> frame tagged (config)# mvr vlan <v_vlan_list> igmp-address (config)# mvr vlan <v_vlan_list> last-member-query-interval (config)# mvr vlan <v_vlan_list> mode (config-if)# mvr immediate-leave (config-if)# mvr name (config-if)# mvr vlan (config)# ntp (config)# ntp (config)# ntp server (config)# port-security (config)# port-security (config)# port-security aging (config)# port-security aging time (config)# port-security link-detection (config-if)# port-security (config-if)# port-security link-detection (config-if)# port-security link-detection action (config-if)# port-security link-detection condition (config-if)# port-security maximum (config-if)# port-security violation (config)# privilege (config)# ptp (config)# ptp <clockinst> domain (config)# ptp <clockinst> filter (config)# ptp <clockinst> mode...88

10 (config)# ptp <clockinst> priority (config)# ptp <clockinst> priority (config)# ptp <clockinst> time-property (config)# ptp <clockinst> uni (config-if)# ptp <clockinst> (config-if)# ptp <clockinst> announce (config-if)# ptp <clockinst> delay-asymmetry (config-if)# ptp <clockinst> delay-mechanism { e2e p2p } (config-if)# ptp <clockinst> delay-req interval <interval> (config-if)# ptp <clockinst> egress-latency <egress_latency> (config-if)# ptp <clockinst> ingress-latency <ingress_latency> (config-if)# ptp <clockinst> sync-interval <interval> (config-if)# pvlan (config-if)# pvlan (config-if)# pvlan isolation (config)# qos (config)# qos map cos-dscp (config)# qos map dscp-classify (config)# qos map dscp-cos (config)# qos map dscp-egress-translation (config)# qos map dscp-ingress-translation (config)# qos qce refresh (config)# qos qce update (config)# qos storm (config-if)# qos cos (config-if)# qos dei (config-if)# qos dpl (config-if)# qos dscp-classify (config-if)# qos dscp-remark (config-if)# qos dscp-translate (config-if)# qos map cos-tag cos (config-if)# qos map tag-cos pcp (config-if)# qos pcp (config-if)# qos policer (config-if)# qos queue-policer queue (config-if)# qos queue-shaper queue (config-if)# qos shaper (config-if)# qos tag-remark (config-if)# qos trust dscp (config-if)# qos trust tag (config-if)# qos wrr (config)# radius-server (config)# radius-server attribute (config)# radius-server attribute (config)# radius-server attribute (config)# radius-server deadtime (config)# radius-server host (config)# radius-server key (config)# radius-server retransmit (config)# radius-server timeout (config)# ring (config)# ring <instance> chain...109

11 (config)# ring <instance> ring (config)# ring <instance> join (config)# ring <instance> x-slave (config)# rmon (config)# rmon alarm (config)# rmon event (config-if)# rmon collection history (config-if)# rmon collection stats (config-if)# shutdown (config)# smtp (config)# smtp (config)# smtp auth (config)# smtp event (config)# smtp port (config)# smtp recipient (config)# smtp server ip-address (config)# smtp username <username> password encrypted (config)# smtp username <username> password none (config)# smtp username <username> password unencrypted (config)# snmp-server (config)# snmp-server (config)# snmp-server access (config)# snmp-server community v2c (config)# snmp-server community v (config)# snmp-server contact (config)# snmp-server engine-id local (config)# snmp-server host (config)# snmp-server location (config)# snmp-server security-to-group (config)# snmp-server trap (config)# snmp-server user (config)# snmp-server version (config)# snmp-server view (config-if)# snmp-server host <conf_name> alarm (config-if)# snmp-server host <conf_name> traps (config-snmps-host)# alarm (config-snmps-host)# host <v_ipv6_ucast> (config-snmps-host)# host <v_ipv4_ucast> (config-snmps-host)# version (config-snmps-host)# informs retries (config-snmps-host)# shutdown (config-snmps-host)# traps (config)# spanning-tree (config)# spanning-tree aggregation (config-stp-aggr)# spanning-tree (config-stp-aggr)# spanning-tree auto-edge (config-stp-aggr)# spanning-tree bpdu-guard (config-stp-aggr)# spanning-tree edge (config-stp-aggr)# spanning-tree link-type (config-stp-aggr)# spanning-tree mst <instance> cost (config-stp-aggr)# spanning-tree mst <instance> port-priority (config-stp-aggr)# spanning-tree restricted-role...125

12 (config-stp-aggr)# spanning-tree restricted-tcn (config)# spanning-tree edge bpdu-filter (config)# spanning-tree edge bpdu-guard (config)# spanning-tree mode (config)# spanning-tree mst <instance> priority <prio> (config)# spanning-tree mst <instance> vlan <v_vlan_list> (config)# spanning-tree mst forward-time (config)# spanning-tree mst max-age (config)# spanning-tree mst max-hops (config)# spanning-tree mst name (config)# spanning-tree recovery interval (config)# spanning-tree transmit hold-count (config-if)# spanning-tree (config-if)# spanning-tree auto-edge (config-if)# spanning-tree bpdu-guard (config-if)# spanning-tree edge (config-if)# spanning-tree link-type (config-if)# spanning-tree mst <instance> cost (config-if)# spanning-tree mst <instance> port-priority (config-if)# spanning-tree restricted-role (config-if)# spanning-tree restricted-tcn (config-if)# speed (config)# switchport (config)# switchport vlan mapping (config-if)# switchport access vlan (config-if)# switchport forbidden vlan (config-if)# switchport hybrid acceptable-frame-type (config-if)# switchport hybrid allowed vlan (config-if)# switchport hybrid egress-tag (config-if)# switchport hybrid ingress-filtering (config-if)# switchport hybrid native vlan (config-if)# switchport hybrid port-type (config-if)# switchport mode (config-if)# switchport trunk allowed vlan (config-if)# switchport trunk native vlan (config-if)# switchport trunk vlan tag native (config-if)# switchport vlan ip-subnet id (config-if)# switchport vlan mac (config-if)# switchport vlan mapping (config-if)# switchport vlan protocol group (config)# tacacs-server (config)# tacacs-server timeout (config)# tacacs-server deadtime (config)# tacacs-server key (config)# tacacs-server host (config)# upnp (config)# upnp (config)# upnp advertising-duration (config)# upnp ttl (config)# username (config)# username<username>privilege<priv>password encrypted (config)# username<username>privilege<priv>password none...141

13 (config)# username<username>privilege<priv>password unencrypted (config)# vlan (config)# vlan (config)# vlan ethertype s-custom-port (config)# vlan protocol (config)# web privilege group...143

14 Chapter 1 Introduction to CLI Welcome to Husky Series HMG-1648P & HMG-1648EP Industrial Gigabit Managed Ethernet Switch. This chapter includes the following topics: About CLI (Console Access) How to access CLI CLI Modes Quick Keys Command Syntax 1-1 About CLI (Console Access) The Husky Series of industrial Ethernet switches provide a number of configuration/management methods. The first and very basic is serial console access. This method is also called out-of-band management and is only available when a terminal or administrator PC can be physically connected to the local Husky Series switch at the CONSOLE port using RJ45 to RS-232 console cable. Accessing the switch via CONSOLE port allows the user to use Command Line Interface (CLI) to manage and configure the device. The out-of-band management is relatively useful when you lose the network connection to the device. The out-of-band management via console access, using a command line (CLI), is familiar to most network engineers. For engineers that are not comfortable using CLI, this device can also be managed using any standard Web Browser in a more user friendly 'point-and-click' method. Therefore, in most configuration scenarios, the console will only be used to initially configure the switch s IP address, so that the device may be accessed via the other methods which require working TCP/IP. After the device has been properly configured for the application and placed into service, a third method of configuration/management can be employed using Simple Network Management Protocol (SNMP). The operator will use SNMP management software to manage and monitor the Husky Series switches on a network. This requires some configuration of the device to allow SNMP management. In addition, the network management platform will need to import and compile the proprietary MIB (management information base) file so that the manager knows "how" to manage the Husky switches 1-2 How to Access CLI Using the provided accessory cable, connect the switch s "CONSOLE" port (RJ-45) to the PC terminal communications port (DB9). Run any terminal emulation program (HyperTerminal, PuTTY, TeraTerm Pro, etc.) and configure the communication Parameters as follows: Speed: 115,200 Data: 8 bits Parity: none Stop bits: 1 Flow Control: None From a warm start, the following screen will be displayed. HMG-1648P & HMG-1648EP CLI Commands 1-1

15 Introduction to CLI # reload warm % Warm reload in progress, please stand by. # Boot> fi lo -d managed Image loaded from 0x x80b773f4 Boot> go Press ENTER to get started By default, at the "Username" prompt, enter 'admin' with no password. 1-3 CLI Modes The Command Line Interface (CLI) of Husky series is mainly divided into four basic modes and these modes are: User Mode EXEC Mode Config Mode Config Interface Mode. After entering the username and password, you start from the EXEC Mode (prompted with # ). The commands available in User mode and EXEC Mode are limited. For more advanced configurations, you must enter Config Mode or Config Interface Mode. In each mode, a question mark (?) at the system prompt can be issued to obtain a list of commands available for each command mode. The following table provides a brief overview of modes available in this device. Mode Prompt Enter Method Exit Method User Mode > enable disable EXEC Mode # Enter authorized username and password Exit, logout Config Mode (config)# Enter configure terminal or config t after # End, exit, do logout Config Interface Mode (config-if)# Specify interface, interface type and number after (config)# End, exit, do logout 1-4 Quick Keys There are several useful quick keys you can use when editing command lines. Keyboard Action? Issue? to get a list of commands available in the current mode. Up arrow key To view the previous entered commands. Down arrow key To view the previous entered commands. Tab key To complete an unfinished command. 1-5 Command Syntax Commands introduced in this user manual are written using the coherent symbols and easy-to-understand syntax and HMG-1648P & HMG-1648EP CLI Commands 1-2

16 Introduction to CLI style. Although users can issue Help command to complete a desired command in CLI, it is useful to understand frequently-used symbols and syntax conventions. The following table lists the syntax conventions used in this user manual together with an example. Example: (config-if-vlan)# ip address { { <address> <netmask> } { dhcp [ fallback <fallback_address> <fallback_netmask> [ timeout <fallback_timeout> ] ] } } Symbol Function Example Explanation < > (Angle bracket) Enter a value, alphanumeric Enter IP address and subnet <address> <netmask> strings or keywords. mask. [ fallback <fallback_address> [ ] Fallback Parameters is an This is optional Parameters. <fallback_netmask> (Square bracket) optional item. [ timeout <fallback_timeout> ] ] A curly bracket has the following two functions: 1. If there are more than two options available, a curly { { <address> <netmask> } { dhcp [ fallback { } bracket can be used to <fallback_address> At least specify one option to (Curly bracket) separate them. <fallback_netmask> complete the command. 2. The uter curly bracket means that this is a must Parameters. At least one value should be specified. [ timeout <fallback_timeout> ] ] } } { { <address> <netmask> } (Vertical bar) { dhcp [ fallback Enter IP address or use DHCP Use a vertical bar to separate <fallback_address> to assign IP address options. <fallback_netmask> automatically. [ timeout <fallback_timeout> ] ] } } HMG-1648P & HMG-1648EP CLI Commands 1-3

17 Chapter 2 Basic Configuration This section introduces users how to change the default IP address to the desired one and save the current running configurations to startup configurations. For detailed introductions to commands, please see chapter 3, chapter 4, and chapter Configuring IPv4 Address IP address: / Subnet mask: erminal (config)# interface vlan 1 (config-if-vlan)# ip address (config-if-vlan)# exit (config)# exit # show ip interface brief Vlan Address Method Status /24 Manual DOWN 2-2 Enter Config Interface Mode Enter Port 3 s Config Interface mode. erminal (config)# interface FastEthernet 1/3 (config-if)# Note: 1/3 means Ethernet Interface 1, Port 3. Enter Port 1~3 s Config Interface mode. erminal (config)# interface FastEthernet 1/1-3 (config-if)# Note: 1/1-3 means Ethernet Interface 1, Port 1 to Port 3. Enter Port 1~3 s Config Interface mode. erminal (config)# interface FastEthernet 1/1-3,5 (config-if)# Note: 1/1-3,5 means Ethernet Interface 1, Port 1 to Port 3 and Port Save Configurations # copy running-config startup-config Building configuration... % Saving 1469 bytes to flash:startup-config HMG-1648P & HMG-1648EP CLI Commands 2-1

18 Basic Configuration # 2-4 Restart the Device # reload warm % Warm reload in progress, please stand by. # Boot> fi lo -d managed Image loaded from 0x x80b773f4 Boot> go Press ENTER to get started 2-5 Load Factory Defaults Load factory default settings # reload defaults % Reloading defaults, attempting to keep IP address. Please stand by. Load factory defaults but keep IP settings # reload defaults keep-ip % Reloading defaults, attempting to keep IP address. Please stand by. 2-6 Check IP address # show interface vlan VLAN1 LINK: a Mtu:1500 <UP BROADCAST RUNNING MULTICAST> IPv4: / IPv6: fe80::218:a9ff:fe00:5170/64 <ANYCAST TENTATIVE AUTOCONF># 2-7 Show System and Software Information # show version MEMORY MAC Address Previous Restart : Total=84417 KBytes, Free=66105 KBytes, Max=66081 KBytes : a : Warm System Contact System Name System Location System Time System Uptime : : : : T09:32:43+08:00 : 00:09:39 HMG-1648P & HMG-1648EP CLI Commands 2-2

19 Basic Configuration SID : Product Software Version Build Date : HMG-1648EP Gigabit Managed Ethernet Switch : "1.108 beta rev.3" (*subject to change) : T08:48:36+08:00 (*subject to change) 2-8 Show SFP Information # show sfp No SFP Module No SFP Module No SFP Module Vendor Name Vendor Part Number Vendor Serial Number Fiber Type Wave Length Link Length TX Power RX Power RX Sensitivity Temperature : : SFP-DD-SXLC : H : Multi : 850 nm : 550 m : -7 dbm : -40 dbm : 0 dbm : 39 degree C 2-9 Show Running Configurations # show running-config Building configuration... username admin privilege 15 password none! vlan 1 HMG-1648P & HMG-1648EP CLI Commands 2-3

20 Basic Configuration!!! no smtp server spanning-tree mst name a revision 0! interface FastEthernet 1/1! interface FastEthernet 1/2! interface FastEthernet 1/3! interface FastEthernet 1/4! interface FastEthernet 1/5! interface FastEthernet 1/6 -- more --, next page: Space, continue: g, quit: ^C 2-10 Show History # show history show sfp show running-config show history > show history config t interface FastEthernet 1/3 exit interface FastEthernet 1/1-5 exit interface FastEthernet 1/1-3,5,7 flowcontrol on exit show interface * status disable show clock detail show dot1x show history 2-11 Help Help command can be issued in User, Exec, and Global Config mode to get a hint message describing how to use show command to get help from CLI. # help HMG-1648P & HMG-1648EP CLI Commands 2-4

21 Basic Configuration Help may be requested at any point in a command by entering a question mark '?'. If nothing matches, the help list will be empty and you must backup until entering a '?' shows the available options. Two styles of help are provided: 1. Full help is available when you are ready to enter a command argument (e.g. 'show?') and describes each possible argument. 2. Partial help is provided when an abbreviated argument is entered and you want to know what arguments match the input (e.g. 'show pr?'.) 2-12 Logout To close an active terminal session, issue the logout command in User or EXEC mode. (config)# exit # logout Press ENTER to get started # disable > logout Press ENTER to get started HMG-1648P & HMG-1648EP CLI Commands 2-5

22 Chapter 3 Commands in User Mode When you successfully login in Command Line Interface, you are in EXEC Mode (prompted with # ). To enter User Mode, issues disable command after # prompt. Then you will be directed to User mode with > prompt. Username: admin Password: # # disable > In User Mode, only limited commands are available. These commands are used for clearing statistics, entering EXEC Mode and ping the specified destination. To configure a function, you should enter Config Mode or Config Interface Mode. 3-1 > clear ip arp Syntax: > clear ip arp Explanation: Clear ARP cache. 3-2 > clear lldp statistics Syntax: > clear lldp statistics Explanation: Clear LLDP statistics. 3-3 > clear statistics Syntax: > clear statistics {[ interface ] ( <port_type> [ <v_port_type_list> ] )} <port_type>: Specify the interface type. [ <v_port_type_list>: Specify the ports that you want to clear. Explanation: Clear statistics of the specified interfaces. 3-4 > enable Syntax: > enable [ <new_priv> ] [ <new_priv: 0-15> ]: Choose a privilege level. HMG-1648P & HMG-1648EP CLI Commands 3-1

23 Commands in User ModeI Explanation: Enter the Exec mode. 3-5 > exit Syntax: > exit Explanation: Return to the previous mode. Issuing this command in User mode will logout the Command Line Interface. 3-6 > help Syntax: > help Explanation: Provide help messages. 3-7 > ping ip Syntax: > ping ip <v_ip_addr> [ repeat <count> ] [ size <size> ] [ interval <seconds> ] <v_ip_addr>: Specify IPv4 address that you want to ping. [ repeat <count> ]: The number of packets that are sent to the destination IP or host. [ size <size> ]: The size of the packet. [ interval <seconds> ]: Timeout interval. The ping test is successful only when it receives echo reply from the destination IP or host within the time specified here. Explanation: To carry out ping tests on the specified destination IPv4 address or host. 3-8 > ping ipv6 Syntax: > ping ipv6 <v_ipv6_addr> [ repeat <count> ] [ size <size> ] [ interval <seconds> ] <v_ipv6_addr>: Specify IPv6 address that you want to ping. [ repeat <count> ]: The number of packets that are sent to the destination IP or host. [ size <size> ]: The size of the ping packet. [ interval <seconds> ]: Timeout interval. The ping test is successful only when it receives echo reply from the destination IP or host within the time specified here. Explanation: To carry out ping tests on the specified destination IPv6 address or host. 3-9 > traceroute Syntax: > traceroute ip <v_ip_addr> [ maxttl <maxttl> ] [ waittime <waittime> ] HMG-1648P & HMG-1648EP CLI Commands 3-2

24 Commands in User ModeI <v_ip_addr>: Specify the IP address of the destination host. [ maxttl <maxttl> ]: Specify the maximum number of hops that the system will trace. [ waittime <waittime> ]: Specify how long the system will wait for a reply. Explanation: Trace the path of a packet to reach the specified IP or host > show commands In User Mode, show commands can be issued to display current status or settings of a certain command. They will be introduced in Chapter 5 Commands in Config Mode. HMG-1648P & HMG-1648EP CLI Commands 3-3

25 Chapter 4 Commands in EXEC Mode 4-1 # clear access management statistics Syntax: # clear access management statistics Explanation: Clear access (HTTP, HTTPs, SNMP, Telnet, SSH) management statistics 4-2 # clear access-list ace statistics Syntax: # clear access-list ace statistics Explanation: Clear access list entry statistics. 4-3 # clear dot1x statistics Syntax: # clear dot1x statistics [ interface ( <port_type> [ <v_port_type_list> ] ) ] [ interface ( <port_type> [ <v_port_type_list> ] ) ]: Specify the interface that you want to clear. Explanation: Clear (the specified interfaces ) dot1x statistics. 4-4 # clear erps Syntax: # clear erps [ <groups> ] statistics [ <groups> ]: Specify the ERPS group that you want to clear. Explanation: Clear (the specified group s) ERPS statistics. 4-5 # clear ip arp Syntax: # clear ip arp Explanation: Clear ARP cache. 4-6 # clear ip dhcp detailed statistics Syntax: # clear ip dhcp detailed statistics { server client snooping relay helper all } [ interface ( <port_type> [ <in_port_list> ] ) ] HMG-1648P & HMG-1648EP CLI Commands 4-1

26 Commands in EXEC Mode { server client snooping relay helper all }: Specify the type of information that you want to clear. [ interface ( <port_type> [ <in_port_list> ] ) ]: Specify the interface type and port number. Explanation: Clear IP DHCP statistics. 4-7 # clear ip dhcp server binding <ip> Syntax: # clear ip dhcp server binding <ip> <ip>: Specify the IP address for this server binding setup. Explanation: Clear automatic, manual or expired server binding caches. 4-8 # clear ip dhcp server binding { automatic manual expired } Syntax: # clear ip dhcp server binding { automatic manual expired } { automatic manual expired }: Specify the server binding mode. Explanation: Clear automatic, manual or expired server binding caches. 4-9 # clear ip dhcp server statistics Syntax: # clear ip dhcp server statistics Explanation: Clear DHCP server statistics # clear ip dhcp relay statistics Syntax: # clear ip dhcp relay statistics Explanation: Clear IP DHCP Relay statistics 4-11 # clear ip dhcp snooping statistics Syntax: # clear ip dhcp snooping statistics [ interface ( <port_type> [ <in_port_list> ] ) ] Explanation: Clear IP DHCP Snooping statistics # clear ip igmp snooping Syntax: # clear ip igmp snooping [ vlan <v_vlan_list> ] statistics Explanation: Clear IP IGMP Snooping statistics. HMG-1648P & HMG-1648EP CLI Commands 4-2

27 Commands in EXEC Mode 4-13 # clear ip statistics Syntax: # clear ip statistics [ system ] [ interface vlan <v_vlan_list> ] [ icmp ] [ icmp-msg <type> ] Explanation: Clear IPv4 statistics for system, interface and ICMP # clear ipv6 mld snooping Syntax: # clear ipv6 mld snooping [ vlan <v_vlan_list> ] statistics Explanation: Clear statistics for IPv6 MLD Snooping # clear ipv6 neighbors Syntax: # clear ipv6 neighbors Explanation: Clear the table for IPv6 neighbors # clear ipv6 statistics Syntax: # clear ipv6 statistics [ system ] [ interface vlan <v_vlan_list> ] [ icmp ] [ icmp-msg <type> ] Explanation: Clear IPv6 statistics for system, interface and ICMP # clear lacp statistics Syntax: # clear lacp statistics Explanation: Clear LACP statistics # clear lldp statistics Syntax: # clear lldp statistics Explanation: Clear LLDP statistics # clear logging Syntax: # clear logging [ info ] [ warning ] [ error ] [ switch <switch_list> ] Explanation: Clear specific syslog events # clear mac address-table Syntax: # clear mac address-table HMG-1648P & HMG-1648EP CLI Commands 4-3

28 Commands in EXEC Mode Explanation: Clear MAC address table # clear mep Syntax: # clear mep <inst> { lm dm tst } Explanation: Clear a specific instance MEP information # clear mvr Syntax: # clear mvr [ vlan <v_vlan_list> name <mvr_name> ] statistics Explanation: Clear MVR statistics # clear spanning-tree Syntax: # clear spanning-tree { { statistics [ interface ( <port_type> [ <v_port_type_list> ] ) ] } { detected-protocols [ interface ( <port_type> [ <v_port_type_list_1> ] ) ] } } Explanation: Clear specific interfaces Spanning Tree statistics # clear statistics Syntax: # clear statistics [ interface ] ( <port_type> [ <v_port_type_list> ] ) Explanation: Clear Fast Ethernet and/or Gigabit Ethernet interfaces statistics erminal Syntax: erminal Explanation: Enter the Global Config mode. erminal (config)# 4-26 # copy Syntax: # copy { startup-config running-config <source_path> } { startup-config running-config <destination_path> } [ syntax-check ] { startup-config running-config <source_path> }: Specify the file type that you want to copy from. This can be startup-config, running-config or a specific source file in flash or TFTP server. { startup-config running-config <destination_path> }: Specify the file type that you want to copy to. This can be startup-config, running-config or a specific destination file in flash or TFTP server. HMG-1648P & HMG-1648EP CLI Commands 4-4

29 Commands in EXEC Mode Explanation: Save running configurations to startup configurations. Sample command: Save running configurations to startup configurations # copy running-config startup-config Building configuration... % Saving 1596 bytes to flash:startup-config # Sample command: Save startup configurations to running configurations # copy startup-config running-config Building configuration... % Saving 1596 bytes to flash:startup-config # 4-27 # delete Syntax: # delete <path> <Path: word>: Name of the file in Flash to be deleted. Explanation: Delete a file saved in Flash # dir Syntax: # dir Explanation: Display files in flash. # dir Directory of flash: r :00: default-config rw :34: startup-config 2 files, bytes total. # 4-29 # disable & # enable Syntax: # disable Explanation: Return to user mode. Syntax: # enable { privilege level } Explanation: Enter exec mode. HMG-1648P & HMG-1648EP CLI Commands 4-5

30 Commands in EXEC Mode # disable > > enable # 4-30 # dot1x Syntax: # dot1x initialize [ interface ( <port_type> [ <plist> ] ) [ interface ( <port_type> [ <plist> ] ) ]: Specify the type of interface that you intend to use. * means all interfaces. <plist>: Specify the ports that apply to this command. Explanation: To initialize dot1x function in an interface immediately # erps Syntax: # erps <group> command {clear force manual} {port0 port1} <group: 1-64>: Specify a group number between 1~64. {clear force manual}: Specify an action. {port0 port1}: Specify port0 (east) or port1 (west) that applies to this command. Explanation: Configure ERPS instance # firmware swap Syntax: # firmware swap Explanation: Use the other standby firmware image file uploaded to flash # firmware upgrade Syntax: # firmware upgrade <TFTPServer_path_file : word> <TFTPServer_path_file: word>: Specify the TFTP server IP address and firmware filename. Explanation: Upgrade the firmware image # ip dhcp retry interface vlan Syntax: # ip dhcp retry interface vlan <vlan_id> HMG-1648P & HMG-1648EP CLI Commands 4-6

31 Commands in EXEC Mode <vlan_id>: Specify the valid VLAN ID for DHCP query. Explanation: Restart the DHCP query process # more Syntax: # more <path> <path>: Specify the filename. Explanation: Display file in Flash or in TFTP server # ping ip Syntax: # ping ip <v_ip_addr> [ repeat <count> ] [ size <size> ] [ interval <seconds> ] <addr>: Specify the IPv4 address for ping test. Explanation: Ping the specified IPv4 address # ping ipv6 Syntax: # ping ipv6 <v_ipv6_addr> [ repeat <count> ] [ size <size> ] [ interval <seconds> ] [ interface vlan <v_vlan_id> ] < v_ipv6_addr >: Specify the IPv6 address for ping test. [ repeat <count> ]: The number of echo packets will be sent. [ size <size> ]: The size or length of echo packets. [ interval <seconds> ]: The time interval between each ping request. [ interface vlan <v_vlan_id> ]: Specify the VLAN ID. Explanation: Ping the specified IPv6 address # ptp Syntax: # ptp <clockinst> local-clock { update } <clockinst: 0-3>: Specify the instance number. { update }: Update the current PTP status. Explanation: Update PTP local clock status. HMG-1648P & HMG-1648EP CLI Commands 4-7

32 Commands in EXEC Mode 4-39 # reload warm Syntax: # reload warm Explanation: Perform a warm reload on the system # reload default Syntax: # reload defaults [keep-ip] [keep-ip]: Keep VLAN 1 IP setting. Explanation: Restore the device to factory default settings # send Syntax: # send { * <session_list> console 0 vty <vty_list> } <message> { * <session_list> console 0 vty <vty_list> }: Choose one of the options. * : Specify * to denote all tty users. <session_list>: Specify a session number between 0 and 16. console 0: This means primary terminal line. <vty_list>: Send a message to a virtual terminal. <message>: Enter a message in 128 characters that you want to send. Explanation: Send messages to other tty lines # terminal editing Syntax: # terminal editing Negation: # no terminal editing Explanation: Enable command line editing Sample command: When terminal editing enabled # terminal editing # show terminal Line is con 0. * You are at this line now. Alive from Console. Default privileged level is 2. Command line editing is enabled Display EXEC banner is enabled. HMG-1648P & HMG-1648EP CLI Commands 4-8

33 Commands in EXEC Mode Display Day banner is enabled. Terminal width is 80. length is 24. history size is 32. exec-timeout is 10 min 0 second. Current session privilege is 15. Elapsed time is 0 day 0 hour 10 min 57 sec. Idle time is 0 day 0 hour 0 min 0 sec. # Sample command: When terminal editing enabled # disable > show terminal Line is con 0. * You are at this line now. Alive from Console. Default privileged level is 2. Command line editing is enabled Display EXEC banner is enabled. Display Day banner is enabled. Terminal width is 80. length is 24. history size is 32. exec-timeout is 10 min 0 second. Current session privilege is 0. Elapsed time is 0 day 0 hour 11 min 24 sec. Idle time is 0 day 0 hour 0 min 0 sec. > Sample command: When terminal editing disabled # no terminal editing # show terminal Line is con 0. * You are at this line now. Alive from Console. Default privileged level is 2. Command line editing is disabled Display EXEC banner is enabled. Display Day banner is enabled. Terminal width is 80. length is 24. HMG-1648P & HMG-1648EP CLI Commands 4-9

34 Commands in EXEC Mode history size is 32. exec-timeout is 10 min 0 second. Current session privilege is 15. Elapsed time is 0 day 0 hour 6 min 33 sec. Idle time is 0 day 0 hour 0 min 0 sec. # 4-43 # terminal exec-timeout Syntax: # terminal exec-timeout <0-1440> [<0-3600>] Negation: # no terminal exec-timeout <0-1440>: Specify the timeout value in minutes. [<0-3600>]: Specify the timeout value in seconds. Explanation: Set up terminal timeout value. (system default value 10 min) Sample command: Set-up longer timeout in exec mode # terminal exec-timeout 60 # show terminal Line is con 0. * You are at this line now. Alive from Console. Default privileged level is 2. Command line editing is enabled Display EXEC banner is enabled. Display Day banner is enabled. Terminal width is 80. length is 24. history size is 32. exec-timeout is 60 min 0 second. Current session privilege is 15. Elapsed time is 0 day 0 hour 20 min 35 sec. Idle time is 0 day 0 hour 0 min 0 sec. # 4-44 # terminal history size Syntax: # terminal history size <0-32> Negation: # no terminal history size HMG-1648P & HMG-1648EP CLI Commands 4-10

35 Commands in EXEC Mode <0-32>: Specify the current history size. 0 means to disable. Explanation: Set up terminal history size # terminal length Syntax: # terminal length <0 or 3-512> Negation: # no terminal length <0 or 3-512>: Specify the lines displayed on the screen. 0 means no pausing. Explanation: Set up terminal length # terminal width Syntax: # terminal width <0 or > Negation: # no terminal width <0 or >: Specify the width displayed on the screen. 0 means unlimited width. Explanation: Set up terminal display width # traceroute ip Syntax: # traceroute ip <v_ip_addr> [ maxttl <maxttl> ] [ waittime <waittime> ] <v_ip_addr>: Specify the IP address of the destination host. [ maxttl <maxttl> ]: Specify the maximum number of hops that the system will trace. [ waittime <waittime> ]: Specify how long the system will wait for a reply. Explanation: Trace the path of a packet to reach the specified IP or host # no port-security shutdown Syntax: # no port-security shutdown [interface (<port_type>[<v_port_type_list>])] [interface (<port_type>[<v_port_type_list>])]: Specify the port type and port numbers that you want to reopen. Explanation: Reopen ports that are shutdown or disabled by Port Security function. HMG-1648P & HMG-1648EP CLI Commands 4-11

36 Commands in EXEC Mode 4-49 # show interface ( <port_type> [ <v_port_type_list> ] ) utp-cable-diagnostic Syntax: # show interface ( <port_type> [ <v_port_type_list> ] ) utp-cable-diagnostic [interface (<port_type>[<v_port_type_list>])]: Specify the port type and port numbers that you want to reopen. Explanation: Issuing this command will run the UTP Cable Diagnostics for 10/100 copper ports. This will take approximately 5 seconds per port. If all ports are selected, this can take approximately 15 seconds. When completed, the page refreshes automatically, and you can view the cable diagnostics results in the cable status table # show command In EXEC Mode, show commands can be issued to display current status or settings of a certain command. They will be introduced in Chapter 5 Commands in Config Mode. HMG-1648P & HMG-1648EP CLI Commands 4-12

-1- Command Guide of SGS T2X

-1- Command Guide of SGS T2X -1- Command Guide of SGS-5220-24T2X Contents Command Guide of SGS-5220-24T2X Chapter 1 COMMAND LINE INTERFACE... 18 1.1 Accessing the CLI... 18 1.2 Command Line Modes... 18 1.3 Requirements... 19 Chapter

More information

-1- Command Guide of MGSW-28240F

-1- Command Guide of MGSW-28240F -1- Command Guide of MGSW-28240F Contents Command Guide of MGSW-28240F Chapter 1 COMMAND LINE INTERFACE... 20 1.1 Accessing the CLI... 20 1.2 Command Line Modes... 20 1.3 Requirements... 21 Chapter 2 CONSOLE

More information

UTC-NS P-4S Command Line Guide

UTC-NS P-4S Command Line Guide UTC-NS3702-24P-4S Command Line Guide P/N 1072833 REV 00.01 ISS 14JUL14 Copyright Trademarks and patents Manufacturer 2014 United Technologies Corporation Interlogix is part of UTC Building & Industrial

More information

Command Guide of WGSW-28040

Command Guide of WGSW-28040 1 Command Guide of WGSW-28040 Contents Command Guide of WGSW-28040 Chapter 1 COMMAND LINE INTERFACE... 12 1.1 Accessing the CLI... 12 1.2 Command Line Modes... 12 1.3 Cammand Help... 13 1.4 Command Line

More information

Amphenol. RJ-Switch. IP67/68 rugged Ethernet Managed Switch RES-SCE-8MG - Command Line Interface

Amphenol. RJ-Switch. IP67/68 rugged Ethernet Managed Switch RES-SCE-8MG - Command Line Interface RJ-Switch IP67/68 rugged Ethernet Managed Switch RES-SCE-8MG - This manual applies to the following products: RES-SCE-8MG (NOLED) (other options) Rugged IP67/68 Managed Ethernet Switch, with SCE2 reinforced

More information

Product features. Applications

Product features. Applications Applications Layer 2+ VLAN static routing application The managed switch features a built-in, robust IPv4/IPv6 Layer 3 traffic static routing protocol to ensure reliable routing between VLANs and network

More information

NS P-4X Managed Switch Command Guide

NS P-4X Managed Switch Command Guide NS4702-24P-4X Managed Switch Command Guide P/N 1073460-EN REV A ISS 06MAR18 Copyright Trademarks and patents Manufacturer Version FCC compliance FCC compliance Canada ACMA compliance 2018 United Technologies

More information

CG-MSW2402TXR CG-MSW1601TXR コマンドリファレンス

CG-MSW2402TXR CG-MSW1601TXR コマンドリファレンス CG-MSW2402TXR CG-MSW1601TXR コマンドリファレンス CLI Reference Guide Y613-10993-02 Rev.A Table of Contents Table of Contents Preface... 10 Intended Audience...11 Document Conventions...11 Chapter 1.Using the CLI...

More information

CLI Reference. SISPM LRT-C and SISPM LRT Managed Hardened PoE+ Switches Rev. B

CLI Reference. SISPM LRT-C and SISPM LRT Managed Hardened PoE+ Switches Rev. B SISPM1040-384-LRT-C and SISPM1040-362-LRT Managed Hardened PoE+ Switches CLI Reference 33729 Rev. B 33729 Rev. B https://www.transition.com Page 1 of 333 Safety Warnings and Cautions These products are

More information

ECS /26/50-Port Layer 2 Gigabit Ethernet Switch and GE PoE Switch. Management Guide.

ECS /26/50-Port Layer 2 Gigabit Ethernet Switch and GE PoE Switch. Management Guide. ECS2000 18/26/50-Port Layer 2 Gigabit Ethernet Switch and GE PoE Switch Management Guide www.edge-core.com MANAGEMENT GUIDE ECS2000-18T GIGABIT ETHERNET SWITCH Layer 2 Gigabit Ethernet Switch with 16

More information

SM8TAT2SA, SM16TAT2SA, and SM24TAT2SA

SM8TAT2SA, SM16TAT2SA, and SM24TAT2SA SM8TAT2SA, SM16TAT2SA, and SM24TAT2SA Smart Managed Switches, 8-/16-/24-Port Gigabit PoE+, 2-Port 100/1000 SFP CLI Reference 33718 Rev. B 33718 Rev. A https://www.transition.com Page 1 of 255 Trademarks

More information

1. Products Overview Major Management Features Product Specification Package Contents Hardware Description...

1. Products Overview Major Management Features Product Specification Package Contents Hardware Description... NGSM24T2 2 1. Products Overview... 9 1.1 Major Management Features... 9 1.2 Product Specification... 10 1.3 Package Contents... 12 2. Hardware Description... 14 3. Preparation for Management... 16 3.1

More information

Yamaha L2 Switch. SWP1 Series(SWP1-8, SWP1-8MMF, SWP1-16MMF) Command Reference Rev

Yamaha L2 Switch. SWP1 Series(SWP1-8, SWP1-8MMF, SWP1-16MMF) Command Reference Rev Yamaha L2 Switch SWP1 Series(SWP1-8, SWP1-8MMF, SWP1-16MMF) Command Reference Rev.2.01.04 2 Command Reference TOC Contents Preface: Introduction...10 Chapter 1: How to read the command reference...11 1.1

More information

SWP-0208G, 8+2SFP. 8-Port Gigabit Web Smart Switch. User s Manual

SWP-0208G, 8+2SFP. 8-Port Gigabit Web Smart Switch. User s Manual SWP-0208G 1 SWP-0208G, 8+2SFP 8-Port Gigabit Web Smart Switch User s Manual Version: 3.4 April 1, 2008 2 TABLE OF CONTENT 1.0 INTRODUCTION...4 1.1 MAIN FEATURES...4 1.2 START TO MANAGE THIS SWITCH...6

More information

48-Port 10/100/1000BASE-T + 4-Port 100/1000BASE-X SFP Gigabit Managed Switch GS T4S

48-Port 10/100/1000BASE-T + 4-Port 100/1000BASE-X SFP Gigabit Managed Switch GS T4S 48-Port 10/100/1000BASE-T + 4-Port 100/1000BASE-X SFP Gigabit Managed Switch GS-4210-48T4S Outlines Product Overview Product Benefits Applications Appendix Product Features 2 / 42 Product Overview Layer

More information

SM8TAT2SA, SM16TAT2SA, and SM24TAT2SA

SM8TAT2SA, SM16TAT2SA, and SM24TAT2SA SM8TAT2SA, SM16TAT2SA, and SM24TAT2SA Smart Managed Gigabit Ethernet PoE+ Switches 8 /16 /24 Port Gigabit PoE+, 2 Port 100/1000 SFP CLI Reference 33718 Rev. C 33718 Rev. C https://www.transition.com Page

More information

SM24TBT2DPA. CLI Reference. Managed Switch, 24-port Gigabit PoE++, 2-port SFP/RJ-45 Combo Rev. B

SM24TBT2DPA. CLI Reference. Managed Switch, 24-port Gigabit PoE++, 2-port SFP/RJ-45 Combo Rev. B SM24TBT2DPA Managed Switch, 24-port Gigabit PoE++, 2-port SFP/RJ-45 Combo CLI Reference 33739 Rev. B 33739 Rev. B https://www.transition.com Page 1 of 321 Safety Warnings and Cautions These products are

More information

LevelOne. User Manual GSW GE + 2 GE SFP Web Smart Switch. Ver. 1.0

LevelOne. User Manual GSW GE + 2 GE SFP Web Smart Switch. Ver. 1.0 LevelOne User Manual GSW-4876 48 GE + 2 GE SFP Web Smart Switch Ver. 1.0 MANAGEMENT GUIDE GSW-4876 WEB SMART SWITCH Layer 2 Gigabit Ethernet Switch with 48 10/100/1000BASE-T Ports (RJ-45) and 2 Gigabit

More information

Gigabit Managed Ethernet Switch

Gigabit Managed Ethernet Switch LGB1110A LGB1126A-R2 Product Data Sheet Gigabit Managed Ethernet Switch Features Overview LGB1110A The Gigabit Managed Ethernet Switches offer L2 features plus advanced L3 features such as Static Route

More information

Chapter 3 Command List

Chapter 3 Command List Chapter 3 Command List This chapter lists all the commands in the CLI. The commands are listed in two ways: All commands are listed together in a single alphabetic list. See Complete Command List on page

More information

Layer 2 Ethernet Switch Allied Telesyn AT-8000S

Layer 2 Ethernet Switch Allied Telesyn AT-8000S Layer 2 Ethernet Switch Allied Telesyn AT-8000S CLI Reference Guide Allied Telesyn AT-8000S CLI Reference Guide Table of Contents Table of Contents Preface... 10 Intended Audience...11 Document Conventions...11

More information

Yamaha L2 Switch. Intelligent L2 PoE SWR2311P-10G Command Reference Rev

Yamaha L2 Switch. Intelligent L2 PoE SWR2311P-10G Command Reference Rev Yamaha L2 Switch Intelligent L2 PoE SWR2311P-10G Command Reference Rev.2.02.11 2 Command Reference TOC Contents Preface: Introduction...12 Chapter 1: How to read the command reference...13 1.1 Applicable

More information

TL-SG2216/TL-SG2424/TL-SG2424P/TL-SG2452. Gigabit Smart Switch REV

TL-SG2216/TL-SG2424/TL-SG2424P/TL-SG2452. Gigabit Smart Switch REV TL-SG2216/TL-SG2424/TL-SG2424P/TL-SG2452 Gigabit Smart Switch REV2.0.0 1910011094 COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES

More information

Catalyst 4500 Series IOS Commands

Catalyst 4500 Series IOS Commands CHAPTER Catalyst 4500 Series IOS Commands New Commands call-home (global configuration) call-home request call-home send call-home send alert-group call-home test clear energywise neighbors clear errdisable

More information

CLI Guide. JetStream 8-Port Gigabit Smart Switch T1500G-10MPS/T1500G-8T (TL-SG2008) T1500G-10PS (TL-SG2210P) REV

CLI Guide. JetStream 8-Port Gigabit Smart Switch T1500G-10MPS/T1500G-8T (TL-SG2008) T1500G-10PS (TL-SG2210P) REV CLI Guide JetStream 8-Port Gigabit Smart Switch T1500G-10MPS/T1500G-8T (TL-SG2008) T1500G-10PS (TL-SG2210P) REV1.0.2 1910012064 COPYRIGHT & TRADEMARKS Specifications are subject to change without notice.

More information

PSGS-2610F L2+ Managed GbE PoE Switch

PSGS-2610F L2+ Managed GbE PoE Switch PSGS-2610F L2+ Managed GbE PoE Switch Overview PSGS-2610F L2+ Managed PoE+ Switch is a next-generation Ethernet Switch offering full suite of L2 features, better PoE functionality and usability, including

More information

MR2324-4C. 24-Port Intelligent Gigabit Ethernet Switch. Management Guide

MR2324-4C. 24-Port Intelligent Gigabit Ethernet Switch. Management Guide MR2324-4C 24-Port Intelligent Gigabit Ethernet Switch Management Guide Management Guide Intelligent Gigabit Ethernet Switch with 24 10/100/1000BASE-T (RJ-45) Ports, and 4 Combination RJ-45/SFP Ports E082004-R01

More information

JetStream L2 Managed Switch

JetStream L2 Managed Switch TL-SG3210/TL-SG3216/TL-SG3424/TL-SG3424P JetStream L2 Managed Switch REV2.1.0 1910011082 COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK

More information

GS-2610G L2+ Managed GbE Switch

GS-2610G L2+ Managed GbE Switch GS-2610G L2+ Managed GbE Switch Overview GS-2610G L2+ Managed Switch is a next-generation Ethernet Switch offering full suite of L2 features, including advanced L3 features such as Static Route that delivers

More information

Gigabit Managed Ethernet Switch

Gigabit Managed Ethernet Switch LGB1110A LGB1152A Product Data Sheet Gigabit Managed Ethernet Switch LGB1110A OVERVIEW The Gigabit Managed Ethernet Switches offer L2 features plus advanced L3 features such as Static Route for Enterprise

More information

Gigabit Managed Ethernet Switch

Gigabit Managed Ethernet Switch LGB1110A LGB1126A-R2 LGB1152A Product Data Sheet Gigabit Managed Ethernet Switch FEATURES L2+ features make the switch easy to manage, provide robust security, and QoS. Offers a built-in device management

More information

Command-Line Interface (CLI Guide)

Command-Line Interface (CLI Guide) LGB5128A SFP Managed Switch Eco Command-Line Interface (CLI Guide) Customer Support Information Order toll-free in the U.S.: Call 877-877-BBOX (outside U.S. call 724-746-5500) FREE technical support 24

More information

T PCT. Smart PoE Switch REV

T PCT. Smart PoE Switch REV T1500-28PCT Smart PoE Switch REV1.0.0 1910011255 COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and

More information

S4xxx CLI Reference Rev. B Rev. B Page 1 of 475

S4xxx CLI Reference Rev. B Rev. B  Page 1 of 475 33559 Rev. B 33559 Rev. B www.transition.com Page 1 of 475 Trademarks All trademarks and registered trademarks are the property of their respective owners. Copyright Notice/Restrictions Copyright 2013-2015

More information

Support STP/RSTP/MSTP, redundant links and IEEE 802.3ad Link Aggregation

Support STP/RSTP/MSTP, redundant links and IEEE 802.3ad Link Aggregation Enhanced Intelligent L2 Media Convertor is designed for Carrier Ethernet media transition, which provides cost-effective solutions for campus, enterprise, and residential access scenarios. The product

More information

Highlights. Datasheet ISCOM2128EA-MA. comboo GE network. Network Security. control, Aggregation. & Management. Advanced QoS. Support IGMP.

Highlights. Datasheet ISCOM2128EA-MA. comboo GE network. Network Security. control, Aggregation. & Management. Advanced QoS. Support IGMP. ISCOM2110EA-MAA Enhanced L2 Carrier Ethernet Access Switch ISCOM2110EA-MAA is designed for Carrier Ethernet access portfolio, which provides cost-effective solutions for campus, enterprise, and residential

More information

FGS-2616X L2+ Managed GbE Fiber Switches

FGS-2616X L2+ Managed GbE Fiber Switches FGS-2616X L2+ Managed GbE Fiber Switches FGS-2616XD FGS-2616XA FGS-2616X Overview FGS-2616X series L2+ Managed Switch are next-generation Fiber Switch offering full suite of L2 features and additional

More information

Managed Gigabit PoE Switch PS2460GM

Managed Gigabit PoE Switch PS2460GM Managed Gigabit PoE Switch PS2460GM Description PS2460GM Enterprise Gigabit Ethernet switch with management function is designed to meet rigorous mission critical applications, such as factory automation,

More information

24-Port: 20 x (100/1000M) SFP + 4 x Combo (10/100/1000T or 100/1000M SFP)

24-Port: 20 x (100/1000M) SFP + 4 x Combo (10/100/1000T or 100/1000M SFP) BGS-20DSFP4C Managed Fiber Switch 24-Port: 20 x (100/1000M) SFP + 4 x Combo (10/100/1000T or 100/1000M SFP) Key Features L2+ features provide better manageability, security, QOS, and performance IEEE 802.3az

More information

T2600G-28TS (TL-SG3424) T2600G-52TS (TL-SG3452) JetStream Gigabit L2 Managed Switch

T2600G-28TS (TL-SG3424) T2600G-52TS (TL-SG3452) JetStream Gigabit L2 Managed Switch T2600G-28TS (TL-SG3424) T2600G-52TS (TL-SG3452) JetStream Gigabit L2 Managed Switch REV1.0.0 1910011258 COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark

More information

SM24TAT4XA. 24-Port 10/100/1000Base-T + 4 1G/10G SFP+ slots Managed POE Switch. User Guide (CLI) Rev.A1 30-Jul-13

SM24TAT4XA. 24-Port 10/100/1000Base-T + 4 1G/10G SFP+ slots Managed POE Switch. User Guide (CLI) Rev.A1 30-Jul-13 SM24TAT4XA 24-Port 10/100/1000Base-T + 4 1G/10G SFP+ slots Managed POE Switch User Guide (CLI) Rev.A1 30-Jul-13 Revision History Date Revision 07/30/2013 A1 Rev.A1 30-Jul-13 CONTENTS Revision History...

More information

Catalyst 4500 Series IOS Commands

Catalyst 4500 Series IOS Commands CHAPTER Catalyst 4500 Series IOS Commands New Commands dot1x guest-vlan supplicant ip dhcp snooping information option allow-untrusted port-security mac-address port-security mac-address sticky port-security

More information

Dual hot-swappable power supply, with voltage/temperature alarms

Dual hot-swappable power supply, with voltage/temperature alarms ISCOM2924G-4C Intelligent Managed Layer-3 Aggregation switch ISCOM2924G-4C provides 24*10/100/1000M Base-T interfaces and 4*10GE SFP+ uplinks with redundant AC or DC power supply. Deployed on the edge

More information

MANAGEMENT GUIDE. Web Smart 10-Port GE PoE Switch. SMCGS10P-Smart

MANAGEMENT GUIDE. Web Smart 10-Port GE PoE Switch. SMCGS10P-Smart MANAGEMENT GUIDE Web Smart 10-Port GE PoE Switch SMCGS10P-Smart Web Smart 10-Port GE PoE Switch Management Guide No. 1, Creation Road III, Hsinchu Science Park, 30077, Taiwan, R.O.C. TEL: +886 3 5638888

More information

RC-ACS-2428B. Overview. Features & Benefits. Gigabit L2+ OAM Managed Fiber Switch with.

RC-ACS-2428B. Overview. Features & Benefits. Gigabit L2+ OAM Managed Fiber Switch with. Gigabit L2+ OAM Managed Fiber Switch with Twin-Rate TM RC-ACS-2428B Overview The RC-ACS-2428B, the next generation L2+ Carrier Ethernet Access Fiber switches from Raycore, is a 20-port GbE SFP, 4-port

More information

EstiNet L2/SDN Switch Web User Interface USER GUIDE

EstiNet L2/SDN Switch Web User Interface USER GUIDE EstiNet L2/SDN Switch Web User Interface USER GUIDE Table of Contents 1 Introduction... 1 2 Status... 3 2.1 System Information... 3 2.2 Logging Message... 5 2.3 Port... 6 2.3.1 Port Statistics... 6 2.3.2

More information

JSH2402GBM. Introduction. Main Features Combo Port Mixed Giga Ethernet SNMP Switch. Picture for reference

JSH2402GBM. Introduction. Main Features Combo Port Mixed Giga Ethernet SNMP Switch. Picture for reference JSH2402GBM 24+2 Combo Port Mixed Giga Ethernet SNMP Switch Introduction Picture for reference The 24+2 Combo Port Mixed Giga Ethernet SNMP Switch is ideal for medium to large Internet bar or enterprise,

More information

JetStream Gigabit Smart Switch

JetStream Gigabit Smart Switch T1600G-28TS (TL-SG2424) T1600G-52TS (TL-SG2452) T1600G-28PS (TL-SG2424P) T1600G-52PS (TL-SG2452P) JetStream Gigabit Smart Switch REV1.1.3 1910011526 COPYRIGHT & TRADEMARKS Specifications are subject to

More information

_ ip address dhcp show ip interface System log Configuration logging on logging host l

_ ip address dhcp show ip interface System log Configuration logging on logging host l CLI Configuration User Manual CLI Configuration User Manual Content Chapter 1 System Status Command... 10 1.1 System Information... 10 1.1.1 show version... 11 1.1.2 show clock... 11 1.2 System Log...

More information

C H A P T E R Commands Cisco SFS Product Family Command Reference OL

C H A P T E R Commands Cisco SFS Product Family Command Reference OL CHAPTER 3 This chapter documents the following commands: aaa accounting, page 3-8 aaa authorization, page 3-9 action, page 3-11 addr-option, page 3-12 authentication, page 3-14 auto-negotiate (Ethernet

More information

S3900 Series Gigabit Stackable Switches

S3900 Series Gigabit Stackable Switches Data Center & Cloud Computing DATASHEET S3900 Series Gigabit Stackable Switches Models: S3900-24T4S, S3900-24F4S, S3900-48T4S REV.1.0 2018 S3900 Series 01 Overview S3900 Series switches are Gigabit Ethernet

More information

PSGS-1526F. Web Smart+ Managed GbE PoE+ Switch

PSGS-1526F. Web Smart+ Managed GbE PoE+ Switch PSGS-1526F Web Smart+ Managed GbE PoE+ Switch Overview PSGS-1526F web smart+ managed GbE PoE+ switch is the next-generation Ethernet switch offering powerful L2 features with better functionality and usability.

More information

Appendix A Command Index A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Appendix A Command Index A B C D E F G H I J K L M N O P Q R S T U V W X Y Z The command index includes all the commands in the Comware Command Manual, which are arranged alphabetically. A B C D E F G H I J K L M N O P Q R S T U V W X Y Z A access-limit accounting accounting optional

More information

Matrix V-Series V2H FAST ETHERNET SWITCH. Configuration Guide

Matrix V-Series V2H FAST ETHERNET SWITCH. Configuration Guide Matrix V-Series V2H124-24 FAST ETHERNET SWITCH Configuration Guide Notice ELECTRICAL HAZARD: Only qualified personnel should perform installation procedures. NOTICE Enterasys Networks reserves the right

More information

GS-5424G User Manual

GS-5424G User Manual GS-5424G User Manual 03-2018 / v1.0 CONTENTS I Introduction... 1 I-1 Overview... 1 I-2 Package Content... 1 I-3 Features... 2 I-4 Product Components... 2 I-4-1 Ports... 2 I-4-2 LED Indicators... 3 II Installation...

More information

MIL-SM24T4DPA GIGABIT ETHERNET SWITCH MANAGEMENT GUIDE

MIL-SM24T4DPA GIGABIT ETHERNET SWITCH MANAGEMENT GUIDE MIL-SM24T4DPA GIGABIT ETHERNET SWITCH MANAGEMENT GUIDE www.edge-core.com MANAGEMENT GUIDE MIL-SM24T4DPA GIGABIT ETHERNET SWITCH Layer 2 Switch with 24 10/100/1000BASE-T (RJ-45) Ports, and 4 Gigabit Combination

More information

24PORT STACKABLE SWITCH SF-0224FS

24PORT STACKABLE SWITCH SF-0224FS 24PORT STACKABLE SWITCH SF-0224FS Management Guide Stackable Fast Ethernet Switch with 24 10/100BASE-TX (RJ-45) Ports, 2 Gigabit Combination Ports (RJ-45/SFP), and 2 1000BASE-T/Stacking Ports Management

More information

12-Port Intelligent Gigabit Ethernet Switch Management Guide

12-Port Intelligent Gigabit Ethernet Switch Management Guide 12-Port Intelligent Gigabit Ethernet Switch Management Guide Management Guide Guide 12-Port Layer 2 Switch Intelligent Gigabit Ethernet Switch with 8 10/100/1000BASE-T (RJ-45) Ports, and 4 Gigabit Combination

More information

Overview of the Cisco NCS Command-Line Interface

Overview of the Cisco NCS Command-Line Interface CHAPTER 1 Overview of the Cisco NCS -Line Interface This chapter provides an overview of how to access the Cisco Prime Network Control System (NCS) command-line interface (CLI), the different command modes,

More information

28-Port L2 Managed Gigabit Switch, 4 x SFP

28-Port L2 Managed Gigabit Switch, 4 x SFP GEL-2861 Version: 1 28-Port L2 Managed Gigabit Switch, 4 x SFP The GEL-2861 is a L2 managed switches designed for the SMB market. The switches can be deployed indifferent target network topologies, from

More information

TL-SL2210/TL-SL2218/TL-SL2428/TL-SL2452. Smart Switch REV

TL-SL2210/TL-SL2218/TL-SL2428/TL-SL2452. Smart Switch REV TL-SL2210/TL-SL2218/TL-SL2428/TL-SL2452 Smart Switch REV1.2.1 1910011603 COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO.,

More information

8-port 10/100/1000M PoE + 2 Gigabit SFP/RJ45 Copper Combo Ports

8-port 10/100/1000M PoE + 2 Gigabit SFP/RJ45 Copper Combo Ports ALL-SG8910PM 8-port 10/100/1000M PoE + 2 Gigabit SFP/RJ45 Copper Combo Ports IEEE 802.3at/af PoE, up to 30W per port Layer 2+ Full Managed Software Features with MSTP, LACP, LLDP, sflow, 802.1X, RADIUS,

More information

AT-GS950/8. AT-GS950/8 Web Interface User Guide AT-S113 Version [ ] Gigabit Ethernet Switch Rev A

AT-GS950/8. AT-GS950/8 Web Interface User Guide AT-S113 Version [ ] Gigabit Ethernet Switch Rev A AT-GS950/8 Gigabit Ethernet Switch AT-GS950/8 Web Interface User Guide AT-S113 Version 1.1.0 [1.00.021] 613-001856 Rev A Copyright 2013 Allied Telesis, Inc. All rights reserved. No part of this publication

More information

TL-SL5428E 24-Port 10/100Mbps + 4-Port Gigabit JetStream L2 Managed Switch

TL-SL5428E 24-Port 10/100Mbps + 4-Port Gigabit JetStream L2 Managed Switch TL-SL5428E 24-Port 10/100Mbps + 4-Port Gigabit JetStream L2 Managed Switch REV2.0.0 1910011020 COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK

More information

NGSME16T2H. (16-port 10/100/1000Base-T + 2 Gigabit SFP L2+ Management PoE Switch)

NGSME16T2H. (16-port 10/100/1000Base-T + 2 Gigabit SFP L2+ Management PoE Switch) NGSME16T2H (16-port 10/100/1000Base-T + 2 Gigabit SFP L2+ Management PoE Switch) More information: WWW.NIVEOPROFESSIONAL.COM INFO@NIVEOPROFESSIONAL.COM Product Specification Introduction The NGSM16ET2H

More information

Powered by Accton. ES3528M ES3552M Fast Ethernet Switch. Management Guide.

Powered by Accton. ES3528M ES3552M Fast Ethernet Switch. Management Guide. Powered by Accton ES3528M ES3552M Fast Ethernet Switch Management Guide www.edge-core.com Management Guide Fast Ethernet Switch Layer 2 Workgroup Switch with 24/48 10/100BASE-T (RJ-45) Ports, and 4 Combination

More information

NGSME24T2H-AV. (24-Rear Port 10/100/1000Base-T PoE + 2 Gigabit SFP Layer 2+ Management Current Sharing PoE+ Switch)

NGSME24T2H-AV. (24-Rear Port 10/100/1000Base-T PoE + 2 Gigabit SFP Layer 2+ Management Current Sharing PoE+ Switch) NGSME24T2H-AV (24-Rear Port 10/100/1000Base-T PoE + 2 Gigabit SFP Layer 2+ Management Current Sharing PoE+ Switch) More information: WWW.NIVEOPROFESSIONAL.COM INFO@NIVEOPROFESSIONAL.COM Product Specification

More information

ES Port Managed Gigabit Switch with 4 SFP ports

ES Port Managed Gigabit Switch with 4 SFP ports ES220-28 28-Port Managed Gigabit Switch with 4 SFP ports Overview With the increasing number of wired and wireless network device, the SOARNEX SOAR series, ES220-28, provides a cost-effective solution

More information

SCALANCE XB-200 Command Line. Interface SIMATIC NET. Industrial Ethernet switches SCALANCE XB-200 Command Line Interface.

SCALANCE XB-200 Command Line. Interface SIMATIC NET. Industrial Ethernet switches SCALANCE XB-200 Command Line Interface. SCALANCE XB-200 Command Line Interface SIMATIC NET Industrial Ethernet switches SCALANCE XB-200 Command Line Interface Configuration Manual Introduction 1 General information 2 Configuration 3 Functions

More information

GS-1626G Web Smart+ GbE Switch

GS-1626G Web Smart+ GbE Switch GS-1626G Web Smart+ GbE Switch Overview GS-1626G Web Smart+ Managed Switch is a next-generation Ethernet Switch offering powerful L2 features and Layer 3 Static Route that delivers the cost-effectively

More information

Highlights. Datasheet ISCOM2110EA-MA. comboo GE network. Network Security. control, & Management. Advanced QoS. U.S.A.

Highlights. Datasheet ISCOM2110EA-MA. comboo GE network. Network Security. control, & Management. Advanced QoS.  U.S.A. ISCOM2110EA-MAA Enhanced L2 Carrier Ethernet Access Switch ISCOM2110EA-MAA is designed for Carrier Ethernet access portfolio, which provides cost-effective solutions for campus, enterprise, and residential

More information

TL-SG5428 TL-SG5412F. 24-Port Gigabit L2 Managed Switch with 4 SFP Slots. 12-Port Gigabit SFP L2 Managed Switch with 4 Combo 1000BASE-T Ports REV2.1.

TL-SG5428 TL-SG5412F. 24-Port Gigabit L2 Managed Switch with 4 SFP Slots. 12-Port Gigabit SFP L2 Managed Switch with 4 Combo 1000BASE-T Ports REV2.1. TL-SG5428 24-Port Gigabit L2 Managed Switch with 4 SFP Slots TL-SG5412F 12-Port Gigabit SFP L2 Managed Switch with 4 Combo 1000BASE-T Ports REV2.1.1 1910010847 COPYRIGHT & TRADEMARKS Specifications are

More information

GV-PoE Switch Comparison Table (Full Version)

GV-PoE Switch Comparison Table (Full Version) GV-PoE Switch Comparison Table (Full Version) Contents 10/100M Web Smart L Switch... 1 GV-POE001 / 01 / 01-V / 01 / 01-V Gigabit Web Smart L Switch...1 GV-POE011-V / 011 / 11 / 11-V / 11 / 11-V Gigabit

More information

User Handbook. Switch Series. Default Login Details. Version 1.0 Edition

User Handbook. Switch Series. Default Login Details. Version 1.0 Edition User Handbook Switch Series Zyxel GS1920 / GS2210 / XGS2210 / GS3700 / XGS3700 / XGS4600 / XS1920 / XS3700 Default Login Details LAN IP Address https://192.168.1.1 User Name admin Password 1234 Version

More information

Highlights. Datasheet. defined E-Line and with specifications. Network Security. control, & Management. Advanced QoS.

Highlights. Datasheet. defined E-Line and with specifications. Network Security. control, & Management. Advanced QoS. ISCOM2924GF-4GE Intelligent Managed Advanced Ethernet Switch ISCOM2924GF-4GE provides 24*100/1000Mbps optical ports+ 4 Gigabits Combo uplinks with redundant AC or DC power supply. Deployed on the edge

More information

Cisco IOS Commands. abort CHAPTER

Cisco IOS Commands. abort CHAPTER CHAPTER 2 abort Use the abort VLAN database command to abandon the proposed new VLAN database, exit VLAN database mode, and return to privileged EXEC mode. abort This command has no arguments or keywords.

More information

OP-MEN 99216B 2 Port (1G/10G) + 12 Port GbE (100M/1G) SFP + 2 RJ45 (100M/1G) Combo L2 Managed Switch

OP-MEN 99216B 2 Port (1G/10G) + 12 Port GbE (100M/1G) SFP + 2 RJ45 (100M/1G) Combo L2 Managed Switch OP-MEN 99216B 2 Port (1G/10G) + 12 Port GbE (100M/1G) SFP + 2 RJ45 (100M/1G) Combo L2 Managed Switch Overview OP-MEN 99216B is next-generation Fiber Switch offering full suite of L2 features and additional

More information

16-port 10/100/1000M PoE + 2 Gigabit SFP/RJ45 Copper Combo Ports

16-port 10/100/1000M PoE + 2 Gigabit SFP/RJ45 Copper Combo Ports ALL-SG8918PM 16-port 10/100/1000M PoE + 2 Gigabit SFP/RJ45 Copper Combo Ports IEEE 802.3at/af PoE, up to 30W per port Layer 2+ Full Managed Software Features with MSTP, LACP, LLDP, sflow, 802.1X, RADIUS,

More information

SCALANCE XB-200 Command Line. Interface SIMATIC NET. Industrial Ethernet switches SCALANCE XB-200 Command Line Interface.

SCALANCE XB-200 Command Line. Interface SIMATIC NET. Industrial Ethernet switches SCALANCE XB-200 Command Line Interface. SCALANCE XB-200 Command Line Interface SIMATIC NET Industrial Ethernet switches SCALANCE XB-200 Command Line Interface Configuration Manual Introduction 1 General information 2 Configuration 3 Functions

More information

ISCOM 2126 Series Switch Command Notebook

ISCOM 2126 Series Switch Command Notebook ISCOM 2126 Series Switch Notebook Software Version ISCOMOS 1.2 Beijing Raisecom Science & Technology Co., Ltd CONTENTS CHAPTER 1. PREFACE... 1 1.1 AUDIENCE... 1 1.2 ABBREVIATION... 1 1.3 REFERENCE... 1

More information

INDUSTRIAL ETHERNET SWITCHES

INDUSTRIAL ETHERNET SWITCHES COMMAND-LINE INTERFACE (CLI) GUIDE LIG1014A, LIG1080A, LIG1082A, LIE1014A, LIE1080A, LIE1082A INDUSTRIAL ETHERNET SWITCHES 24/7 AT OR VISIT BLACKBOX.COM P1 P2 ALM P1 P2 ALM POE P1 P2 ALM 1 2 1 2 1 2 3

More information

JetNet 5428Gv2. Features. Industrial 24FE+4G Gigabit Managed Ethernet Switch INDUSTRIAL ETHERNET RACKMOUNT SWITCH

JetNet 5428Gv2. Features. Industrial 24FE+4G Gigabit Managed Ethernet Switch INDUSTRIAL ETHERNET RACKMOUNT SWITCH INDUSTRIAL ETHERNET RACKMOUNT SWITCH Industrial 24FE+4G Gigabit Managed Ethernet Switch JetNet 5428Gv2 The JetNet 5428G is a 19-inch Gigabit Layer 2+ Industrial switch, equipped with 24 100 Base-TX ports

More information

Appendix A Command Index

Appendix A Command Index Appendix A Command Index The command index includes all the commands in the Command Manual, which are arranged alphabetically. A B C D E F G H I J K L M N O P Q R S T U V W X Y Z A aaa nas-id profile 21-AAA

More information

IPS-3106 SERIES Managed Industrial PoE Ethernet Switch

IPS-3106 SERIES Managed Industrial PoE Ethernet Switch IPS-3106 SERIES Managed Industrial PoE Ethernet Switch Network Management User s Manual Version 0.96 1 Trademarks Contents are subject to revision without prior notice. All other trademarks remain the

More information

Datasheet. comboo GE network. Highlights. Network Security. control, & Management. Advanced QoS. U.S.A. Headquarters.

Datasheet. comboo GE network. Highlights. Network Security. control, & Management. Advanced QoS.  U.S.A. Headquarters. ISCOM2128EA-MAA Enhanced L2 Carrier Ethernet Access Switch ISCOM2128EA-MAA is designed for Carrier Ethernet access portfolio, which provides cost-effective solutions for campus, enterprise, and residential

More information

EPS PoE+ ports 10/100/1000Mbps RJ combo uplink ports (10/100/1000 Mbps RJ-45 and 100/1000Mbps SFP slot) Managed Ethernet PoE Switch

EPS PoE+ ports 10/100/1000Mbps RJ combo uplink ports (10/100/1000 Mbps RJ-45 and 100/1000Mbps SFP slot) Managed Ethernet PoE Switch EPS-3128 24 PoE+ ports 10/100/1000Mbps RJ-45 + 4 combo uplink ports (10/100/1000 Mbps RJ-45 and 100/1000Mbps SFP slot) Managed Ethernet PoE Switch Network Management User s Manual Version 0.90 1 Revision

More information

XSNet S4124SW. This quick start guide describes how to install and use the Managed Ethernet Switch.

XSNet S4124SW. This quick start guide describes how to install and use the Managed Ethernet Switch. Manual Quick Start Guide This quick start guide describes how to install and use the Managed Ethernet Switch. Functional Description RS-232 console, Telnet, SNMP v1 & v2c & v3, RMON, Web Browser, and TFTP

More information

SISGM D-LRT. CLI Reference. 12-Port Managed Industrial Ethernet Switch Rev A Rev. A https://www.transition.

SISGM D-LRT. CLI Reference. 12-Port Managed Industrial Ethernet Switch Rev A Rev. A https://www.transition. SISGM1040-184D-LRT 12-Port Managed Industrial Ethernet Switch CLI Reference 33711 Rev A 33711 Rev. A https://www.transition.com Page 1 of 117 Safety Warnings and Cautions These products are not intended

More information

CL-SW10G Port GbE (100M/1G)SFP + 4 TP/(100/1G) SFP Combo + 4-Port 1G/10G SFP+ L2 Plus Carrier Ethernet Switch

CL-SW10G Port GbE (100M/1G)SFP + 4 TP/(100/1G) SFP Combo + 4-Port 1G/10G SFP+ L2 Plus Carrier Ethernet Switch Key Features L2+ features provide better manageability, security, QoS, and performance IEEE 802.3ah MAC Layer OAM and IEEE802.1ag Ethernet CFM ITU-T Y.1731 Ethernet OAM Performance monitoring 802.3az Energy

More information

JetNet 6528Gf. Features. Industrial 28G Full Gigabit Managed Ethernet Switch INDUSTRIAL ETHERNET RACKMOUNT SWITCH

JetNet 6528Gf. Features. Industrial 28G Full Gigabit Managed Ethernet Switch INDUSTRIAL ETHERNET RACKMOUNT SWITCH INDUSTRIAL ETHERNET RACKMOUNT SWITCH Industrial 28G Full Gigabit Managed Ethernet Switch JetNet 6528Gf The JetNet 6528Gf series is a 19-inch Full Gigabit Layer 2+ Industrial switch and is specially designed

More information

NGSME48T2H. (48-Port 10/100/1000Base-T Gigabit Combo TP/SFP Layer 2+ Full Management High Power PoE Switch)

NGSME48T2H. (48-Port 10/100/1000Base-T Gigabit Combo TP/SFP Layer 2+ Full Management High Power PoE Switch) NGSME48T2H (48-Port 10/100/1000Base-T+ 2 10-Gigabit Combo TP/SFP Layer 2+ Full Management High Power PoE Switch) * 48-Port PoE Gigabit Copper + 2-port 10-Gigabit ComboTP/ SFP+ * 802.3az Energy Efficient

More information

28 Port Fiber Gigabit with 10G SFP+ Management Switch

28 Port Fiber Gigabit with 10G SFP+ Management Switch 28 Port Fiber Gigabit with 10G SFP+ Management Switch ES220-28-24F Gigabit Fiber applies in longer distance for Surveillance, Enterprise, Campuses and Data Centers To meet the backbone application of surveillance,

More information

Highlights. Datasheet ISCOM2924GF-4C. defined E-Line and with specifications. Network Security. control, & Management. Advanced QoS.

Highlights. Datasheet ISCOM2924GF-4C. defined E-Line and with specifications. Network Security. control, & Management. Advanced QoS. Intelligent Managed Advanced Ethernet Switch provides 24*100/1000Mbps optical ports+ 4*10GE SFP+ + uplinks with redundant AC or DC power supply. Deployed on the edge of carrier Ethernet networks, it supports

More information

HES-3106 SERIES 6 PORTS 10/100/1000BASE-T ETHERNET MANAGED SWITCH

HES-3106 SERIES 6 PORTS 10/100/1000BASE-T ETHERNET MANAGED SWITCH HES-3106 SERIES 6 PORTS 10/100/1000BASE-T ETHERNET MANAGED SWITCH 5 PORTS 10/100/1000BASE-T ETHERNET MANAGED SWITCH WITH 1 PORT 1000BASE-X or 100/1000BASE-X UPLINK 5 PORTS 10/100/1000BASE-T ETHERNET MANAGED

More information

VSC6812SDK and VSC6813SDK

VSC6812SDK and VSC6813SDK PRODUCT BRIEF VSC6812SDK and VSC6813SDK WebStaX and SMBStaX Software Development Kits for Vitesse s Managed Enterprise Switches Best-in-class software development kit (SDK) for standalone and stackable

More information

NS3550-2T-8S NS3550-8T-2S

NS3550-2T-8S NS3550-8T-2S Network Transmission Industrial Gigabit Managed Switches 8+2 Industrial Gigabit Fiber Managed Switch 8+2 Industrial Gigabit Managed Switch OVERVIEW The IFS Industrial Gigabit Managed Switches by Interlogix

More information

PS3268C User's Manual

PS3268C User's Manual PS3268C User's Manual 24 RJ-45 + 2 Combo port Web Smart Switch, PoE 370W Release 1.00 2015, Manufacture Corporation. All rights reserved. All brand and product names are trademarks or registered trademarks

More information

Industrial Managed Ethernet Switch Software User Manual Last Update: September 10, 2015 Version 2.4.0

Industrial Managed Ethernet Switch Software User Manual Last Update: September 10, 2015 Version 2.4.0 Barox Industrial Managed Ethernet Switch Software User Manual Last Update: September 10, 2015 Version 2.4.0 Contents Introduction... 1 Web Console Configuration... 4 Basic Settings... 6 Port Management...

More information

48-Port Gigabit with 4 Shared SFP Managed Switch

48-Port Gigabit with 4 Shared SFP Managed Switch 48-Port Gigabit with 4 Shared SFP Managed Switch High-Density / Cost-effective / Telecom class Gigabit solution for Enterprise backbone and Data Center Networking The PLANET is a Layer 2 / Layer 4 full

More information

SOLO NETWORK (11) (21) (31) (41) (48) (51) (61)

SOLO NETWORK (11) (21) (31) (41) (48) (51) (61) (11) 4062-6971 (21) 4062-6971 (31) 4062-6971 (41) 4062-6971 (48) 4062-6971 (51) 4062-6971 (61) 4062-6971 Cisco SRW224G4 24-Port 10/100 + 4-Port Gigabit Switch: WebView Cisco Small Business Managed Switches

More information