HDMI to HDBaseT Matrix Switcher

Transcription

1 Opus 4K HD HDMI to HDBaseT Matrix Switcher Application Programming Interface AT-OPUS-810M AT-OPUS-68M AT-OPUS-46M API

2 Version Information Version elease Date Notes 1 10/18 Initial release 2 12/18 Parity added to S232para command AT-OPUS API 2

3 Table of Contents Commands 4 AT-OPUS API 3

4 The following tables provide an alphabetical list of commands available on the AT-OPUS. Commands can be sent using S-232, TCP/IP, or Telnet. Default port for Telnet is 23. Each command is case sensitive, do not change: capitalization, spacing, or lettering. Each command is terminated with a carriage return. If the command fails or is incorrect the feedback should be Command FAIED: followed by the sent command. IMPOTANT: Each command is terminated with a carriage-return (0x0d) and the feedback is terminated with a carriage-return and line-feed (0x0a). Command All# Blink Broadcast Clear CSpara EDIDMSet EDIDOut save fw_upgrade HTTPPort IPAddUser IPCFG IPChangePass IPDelUser IPDHCP IPogin IPPort IPQuit IPStatic IPTimeout IOFF ION ocali ock Mreset PWOFF Description esets all inputs to corresponding outputs Enable/Disable red and blue alternating blinking of the PW button ED Enables, disables, and displays status of broadcast mode Erases the saved I/O route settings for the chosen preset number Set S-232 parameter Sets the EDID of an input to default, internal, or a previously saved EDID Saves the output EDID to memory Starts the firmware upgrade process Set the TCP/IP port for HTTP Add a user for TCP/IP control Displays IP address configuration Update the TCP/IP username and password Delete a user from TCP/IP control Turns DHCP on / off Enables / Disables IPogin mode Set the TCP/IP port for telnet ogs out of current TCP/IP session Sets a static IP address Determines amount of seconds of inactivity before TCP/IP disconnects Disables the front panel I receiver window Enables the front panel I receiver window Set local I channel routing commands ocks the front panel of the matrix so no buttons are active Sets matrix back to the default settings Turns the unit off AT-OPUS API 4

5 Command PWON PWSTA eboot ecall ecalla ecallv S232para rx_upgrade Description Turns the unit on Displays the power status of the matrix eboots the system ecalls saved I/O route settings for the chosen preset number ecalls saved audio route settings for the number you selected ecalls saved video route settings for the number you selected Sets the parameters for the HDBaseT S-232 output ports Starts the firmware update process for the receiver Save Saves I/O route settings for future use, preset options 1 to 50 SaveA Saves the current audio route settings, preset options 1 to 50 SaveV Saves the current video route settings, preset options 1 to 50 Status Statusx sddp_announce set_host_name show_host_name Type Unlock Version view_log VIN VOUT VOUTMute x?all x?$ x?ax& x?vx& x?avx& Displays which inputs are currently routed to which outputs Displays which input is currently routed to the indicated output Triggers SDDP announcement Set host name for SDDP protocol Displays the current host name Brings up the model information Unlocks the front panel of the matrix, enabling the buttons again Brings up the current firmware version View the matrix log data Adjusts the volume of the input Adjusts the volume of the output Mutes/Unmutes audio output volume outes selected input to all outputs Mutes/Unmutes AV signals for the specified output channel Switch the audio input to the selected output Switch the video input to the selected output Switch a specific input to a specific output AT-OPUS API 5

6 All# esets all inputs to corresponding outputs. All# All# x1avx1, x2avx2, x3avx3, x4avx4, x5avx5, x6avx6, x7avx7, x8avx8 Blink Enable/Disable red and blue alternating blinking of the PW button ED. Default is off. Blink X X Value on, off, sta Blink sta Blink off Broadcast Enables, disables, and displays status of broadcast mode. Default is off. Broadcast X X Value on, off, sta Broadcast sta Broadcast on Clear Erases the saved I/O route settings for the chosen preset number. ClearX X I/O preset number 1 to 50 Clear2 Clear2 AT-OPUS API 6

7 CSpara Set the matrix S-232 baud rate. CSpara[X] X Baud rate 2400, 4800, 9600, 19200, 38400, 57600, CSpara[115200] CSpara[115200] EDIDMSet Sets the EDID of an input to default, internal, or a previously saved EDID. EDID is set to default with factory settings. EDIDMSetX YZ X Input 1 to 8 Y EDID type default, save, int Z Value save - 1 to 10 (810M), 1 to 8 (68M), 1 to 6 (46M) int - 1 to 16 EDIDMSet1 default EDIDMSet2 save2 EDIDMSet3 int3 Internal EDIDs 1: 1080p / 2 channel audio 2: 1080p / multichannel audio (lossless) 3: 1080p 3D / Dolby Digital audio 4: 1080p 3D / 2 channel audio 5: 1080p 3D / multichannel audio (lossless) 6: 1080p 3D / Dolby Digital audio 7: 720p / 2 channel audio 8: 720p / Dolby Digital audio EDIDMSet1 default EDIDMSet2 save2 EDIDMSet3 int3 9: 1280x800 GB / 2 channel audio 10: 1366x768 GB / 2 channel audio 11: 1080p DVI 12: 1280x800 GB DVI 13: 4K 30Hz / 2 channel audio 14: 4K 30Hz / multichannel audio 15: 4K 60Hz / 2 channel audio 16: 4K 60Hz / multichannel audio AT-OPUS API 7

8 EDIDOut save Saves the output EDID to memory. EDIDOutX savey X Value 1 to 10 (810M), 1 to 8 (68M), 1 to 6 (46M) Y Value 1 to 50 EDIDOut2 save15 EDIDOut2 save15 fw_upgrade Starts the firmware upgrade process. fw_upgrade fw_upgrade fw_upgrade HTTPPort Sets the TCP/IP port for HTTP. Default is 80. HTTPPort X X Port 0 to HTTPPort 50 HTTPPort 50 AT-OPUS API 8

9 IPAddUser Add a user for TCP/IP control. IPAddUser X Y X User name 20 characters (max) Y Password 20 characters (max) IPAddUser ABCd Y4n IPAddUser ABCd Y4n TCP/IP user was added IPCFG Displays IP address configuration. IPCFG IPCFG MAC addr: A1:23:B4:56:78:C9 IP addr: Netmask: Gateway: Web Port: 80 IP Port: 23 IPChangePass Update the TCP/IP username and password. IPChangePass W X Y Z W Old username 20 characters (max) X Old password 20 characters (max) Y New password 20 characters (max) Z New password confirmation 20 characters (max) IPChangePass ABCd Y4n Y56c Y56c IPChangePass ABCd Y4n Y56c Y56c AT-OPUS API 9

10 IPDelUser Delete a user from TCP/IP control. IPDelUser X X User name 20 characters (max) IPDelUser ABCd IPDelUser ABCd TCP/IP user was deleted IPDHCP Turns DHCP on / off. Default is on. IPDHCP X X Value on, off, sta IPDHCP on IPDHCP on IPogin Enables / Disables IPogin mode. Default is off. IPogin X X Value on, off, sta IPogin off IPogin off AT-OPUS API 10

11 IPPort Set the TCP/IP port for telnet. Default is 23. IPPort X X Port 1 to 65535, sta IPPort 23 IPPort 23 IPQuit ogs out of current TCP/IP session. IPQuit IPQuit IPQuit IPStatic Sets a static IP address. IPStatic X Y Z X IP address 0 to 255 (per byte) Y Subnet mask 0 to 255 (per byte) Z Gateway (router) 0 to 255 (per byte) IPStatic IPStatic AT-OPUS API 11

12 IPTimeout Determines amount of seconds of inactivity before the telnet session disconnects. Default is 300 seconds. IPTimeout X X Interval (in seconds) 1 to 3600 IPTimeout 300 IPTimeout 300 IOFF Disables the front panel I window. IOFF IOFF IOFF ION Enables the front panel I window. ION ION ION ocali Sets the I route for the matrixed I outputs. The last two I outputs on the OPUS are always matrixed. ocali X Y X Input I channel 1 to 8 (810M), 1 to 6 (68M), 1 to 4 (46M) Y ocal I channel 9 or 10 (810M), 7 or 8 (68M), 5 or 6 (46M) ocali 4 9 I out channel 9 follows I input 4 AT-OPUS API 12

13 ock ocks the front panel of the matrix so no buttons are active. The PW led will blink blue when locked. ock ock ock Mreset Sets matrix back to the default settings. Meset Mreset Mreset PWOFF Turns the unit off. Front panel ED will illuminate red when off. PWOFF PWOFF PWOFF PWON Turns the unit on. Front panel ED will illuminate blue when on. PWON PWON PWON PWSTA Displays the power status of the matrix. PWSTA PWSTA PWON AT-OPUS API 13

14 eboot eboots the matrix. eboot eboot ebooting system... ecall ecalls saved Audio and Video route settings of the chosen preset number. ecallx X Preset 1 to 50 ecall3 ecall3 Done! ecalla ecalls saved Audio route settings of the chosen preset number. ecallax X Preset 1 to 50 ecalla11 ecalla11 Done! ecallv ecalls saved Video route settings of the chosen preset number. ecallvx X Preset 1 to 50 ecallv16 ecallv16 Done! AT-OPUS API 14

15 S232para Sets the parameters for the HDBaseT S-232 zone output ports. S232paraX[Y,Z] X Zone 1 to 8 (810M), 1 to 6 (68M), 1 to 4 (46M) Y Baud rate 2400, 4800, 9600, 19200, 38400, 57600, Z Parity 0 (none), 1 (Even), 2 (odd), 3 (mark), 4 (space), sta S232para4[sta] S232para4[9600,1] rx_upgrade Starts the firmware upgrade process for the receivers. rx_upgradex X Zone 1 to 8 (810M), 1 to 6 (68M), 1 to 4 (46M) rx_upgrade3 rx_upgrade3 Save Saves Audio and Video route settings for future use, preset options 1 to 50. SaveX X Preset 1 to 50 Save1 Save1 Done! AT-OPUS API 15

16 SaveA Saves Audio route settings for future use, preset options 1 to 50. SaveAX X Preset 1 to 50 SaveA12 SaveA12 Done! SaveV Saves Video route settings for future use, preset options 1 to 50. SaveVX X Preset 1 to 50 SaveV21 SaveV21 Done! sddp_announce Triggers the SDDP announcement. sddp_announce sddp_announce sddp_announce set_host_name Set the host name for SDDP protocol. set_host_name X X Variant host name - up to 40 characters, no spaces set_host_name Peanut Host name changed to: Peanut AT-OPUS API 16

17 show_host_name Displays the current host name for SDDP protocol. show_host_name show_host_name Host name: Peanut Status Displays the current route status. Status X X Variant A, V, or AV Status Status V Statusx Displays which inputs are currently connected to which outputs. Statusx? Y x3vx1, x1vx2, x1vx3, x5vx4, x7vx5, x4vx6, x8vx7, x3vx8, x5vx9, x2vx10 x4ax1, x1ax2, x6ax3, x8ax4, x3ax5, x1ax6, x2ax7, x3ax8, x6ax9, x5ax10 x3vx1, x1vx2, x1vx3, x2vx4, x7vx5, x4vx6, x8vx7, x3vx8, x5vx9, x2vx10? Output 1 to 8 (810M), 1 to 6 (68M), 1 to 4 (46M) Y Variant A, V, or AV Statusx4 AV Statusx9 V x5vx4 x2ax4 x5vx9 AT-OPUS API 17

18 Type Brings up the model information. Type Type AT-OPUS-810M Unlock Unlocks the front panel of the matrix, enabling the buttons again. Unlock Unlock Unlock Version Brings up the current firmware version. Version Version Firmware view_log Brings up the current firmware version. view_log X X Parameter all or log count number view_log Atlona UI: AT-OPUS-810M FW Version: og item count: 172 og from: :40: AC :28:34 HS>VIDEO PowerUp Done AT-OPUS API 18

19 VIN Adjusts the volume level of the input. VINX Y X Input Channel 1-24 (810M), 1-19 (68M), 1-14 (46M) Y Value +, -, or -10 to 10 VIN1 - VIN4-5 VIN1 8 VIN4-5 VOUT Adjusts the analog audio output volume level. VOUTX Y X Audio Output Channel 1-10 (810M), 1-8 (68M), 1-6 (46M) Y Value +, -, or -71 to 15 VOUT3-50 VOUT3-50 VOUTMute Mutes/Unmutes analog audio output volume by channel. VOUTMuteX Y X Audio Output Channel 1-10 (810M), 1-8 (68M), 1-6 (46M) Y Value on, off, sta VOUTMute3 sta VOUTMute3 on AT-OPUS API 19

20 x?all outes selected input to all outputs. x?all? Input 1-8 (810M), 1-6 (68M), 1-4 (46M) x3all x3all x?$ Mutes/Unmutes AV signals for the specified output channel. x?$ Y X Output 1-10 (810M), 1-8 (68M), 1-6 (46M) Y Variable on, off, sta x2$ sta x2$ on x?avx& Switch audio and video input to output. x?avx&? Input 1-8 (810M), 1-6 (68M), 1-4 (46M) & Output 1-10 (810M), 1-8 (68M), 1-6 (46M) x1avx3 x1avx3 AT-OPUS API 20

21 x?ax& Switch audio input to output. x?ax&? Input 1-24 (810M), 1-19 (68M), 1-14 (46M) & Output 1-10 (810M), 1-8 (68M), 1-6 (46M) x5ax4 x5ax4 x?vx& Switch video input to output. x?vx&? Input 1-8 (810M), 1-6 (68M), 1-4 (46M) & Output 1-10 (810M), 1-8 (68M), 1-6 (46M) x2vx7 x2vx7 AT-OPUS API 21

22 TM TM Audio Inputs The audio inputs are. AT-OPUS-810M POWE ENTE FNC CANCE EDID INFO OPUS TM AT-OPUS-810M HDMI IN HDBaseT OUT HDMI OUT CHASSIS GOUND AT-OPUS-68M X TX S ON AN DEBUG S-232 I IN AUDIO IN AUDIO OUT S S S S S S S S S S S S S S S S S S TOS IN TOS OUT I IN I OUT 5 POWE ENTE OFF PW: VAC 50/60Hz FNC CANCE EDID INFO OPUS AT-OPUS-68M AT-OPUS-810M TOS IN HDMI IN X TX S AN DEBUG S-232 I IN AUDIO IN AUDIO OUT S S S S S S S S S S S S S S I I OUT TOS OUT IN HDBaseT OUT ON HDMI OUT CHASSIS GOUND AT-OPUS-46M POWE ENTE FNC CANCE EDID INFO OPUS AT-OPUS-46M AT-OPUS-810M 1 2 TOS IN HDMI IN X TX S AN DEBUG S-232 I IN AUDIO IN AUDIO OUT S S S S S S S S S S TOS OUT I IN I OUT HDBaseT OUT ON HDMI OUT CHASSIS GOUND AT-OPUS API 22

23 atlona.com Atlona Inc. All rights reserved. Atlona and the Atlona logo are registered trademarks of Atlona Inc. All other brand names and trademarks or registered trademarks are the property of their respective owners. Pricing, specifications and availability subject to change without notice. Actual products, product images, and online product images may vary from images shown here. AT-NPIB