Ref: A. Leon Garcia and I. Widjaja, Communication Networks, 2 nd Ed. McGraw Hill, 2006 Latest update of this lecture was on

Transcription

1 IP Version 4 (IPv4) Header (Continued) Identification (16 bits): One of the parameters of any network is the maximum transmission unit (MTU) parameter. This parameter specifies the maximum size of the packets that can pass through it. If a packet with size greater the MTU of a specific network needs to be transmitted over that network, it must be broken into smaller parts or otherwise it will be dropped. The Identification component of the header is used by the IP protocol whenever fragmentation (breaking the packet into smaller pieces called fragments) of a packet is performed (if fragmentation is not used, this parameter is set to 0). That is, a long packet is fragmented to smaller pieces because the network over which the packet is to be transmitted does not support the original long packet. Each fragment will be sent over the network as if it is an independent packet. Since fragments of many packets may be in transit at the same time (the different pieces of many packets are being carried over the network and have not been received yet), an identification that allows the receiving machine to know which original packet does each fragment belong to is needed. The identification will be set to a random number (one value out of a possible of values can be used) for each original packet (so all the fragments of a specific packet will have the same identification number) and this specific identification number is not used again for some time to insure that fragments of the different packets don t get mixed up (fragments of first fragmented packet with identification x do not get mixed up with fragments of second fragmented packet with the same identification x that was generated later). To avoid the mixing of fragments of packets with the same identification numbers, sufficiently long time must pass before reusing the same identification numbers again to insure that the fragments of a packet with the previous similar identification number have already been received completely or dropped. If fragments of a specific packet reach a physical network that only supports packet sizes smaller than their size, 1

2 these fragments will be fragmented again. The reassembling of fragments is done only at the destination machine where this machine waits until it receives all fragments of a packet and then reassembles the different components to form the original packet. Once the destination machine receives a fragment of a packet, it sets a timer. If one or more fragments of the packet are lost (they do not arrive before the timer expires), the destination machine will discard the rest of the packet. Flags (3 bits): One bit of flags is not used. Another bit of the flags is (Don t Fragment) which is used by the source machine to request from the routers carrying the packet not to fragment that packet. In this situation, if a router finds that it has to fragment a packet because the physical layer over which it will send the packet does not support the size of the packet, it will drop the packet and send back to the source an ICMP message informing it of this situation. The third bit is (More Fragments) which is used by the fragmenting machine to indicate to the destination machine if there are more fragments or not. That is, all fragments except the last one will have this bit set to 1, while the last fragment will have this bit set to 0. Fragment Offset (13 bits): The identification and Flags indicate which packet do fragments belong to and if there are more fragments coming or not. But they do not indicate the order of fragments (or the location of a fragment inside the original packet). This is done by the fragment offset, where the fragment offset represent the location of the first byte in the fragment within the data of the original packet. Since the fragment offset is 13 bits (giving 2 13 values) while the total length of the packet is 16 bits (giving 2 16 values), the fragmentation process is designed such that each fragment (except the last one) must have a size that is multiple of 8. That is, the fragment offset represents the 13 most significant bits of the location of the first byte of the fragment inside the data part of the original packet, where the 3 least significant bits are assumed to be 000. Remember that 2 16 /2 13 = 8. So, o if Fragment Offset = ( ) 2, this represents the first fragment because the first byte in the fragment is the byte ( ) 2 in the data part of original packet. o if Fragment Offset = ( ) 2, this indicates that the first byte in the fragment is the byte ( ) 2 = 8 in data part of the original packet. o if Fragment Offset = ( ) 2, this indicates that the first byte in the fragment is the byte ( ) 2 = 16 in the data part of the original packet. o if Fragment Offset = ( ) 2, this indicates that the first byte in the fragment is the byte ( ) 2 = 24 in the data part of the original packet. o And so on. The process of fragmentation and reassembling fragments is shown in the following figure. 2

3 In the above figure, if the Don t Fragment flag of the packets sent over Network 1 was set to logic 1, all packets will be dropped by the router and ICMP messages will be sent to the source machine. Note that a packet (or even a fragment) with a size that is smaller than or equal to the MTU of a network will not be fragmented even if its data is not a multiple of 8 (for example, if the data part of a packet is 86 bytes long (which is not a multiple of 8) and the MTU of a network allows a maximum data length of 87 bytes, this packet will be transmitted without fragmentation. This is also true if the 86 bytes was the remaining part of a packet after it was fragmented. The last fragment may have a data length of 86 bytes since there are no more fragments following it so its data length does not have to be a multiple of 8). Time to Live (8 bits): Sometimes packets get lost in the network where routers have trouble sending them to the destination, so they keep hopping from one router to another aimlessly. If a sufficient number of packets keep hopping in circles for an indefinite amount of time without aim between routers, they may bring down the network. To prevent this from happening, the time to live component is set to a specific value (with 8 bits so it has a maximum value of 255) such that each router that the packet passes over decrements this value by one. If the packet does not reach its final destination before this number reaches 0, the packet is dropped (because most likely it was lost) and an ICMP message is sent back to the source machine to indicate to it that its packet has been dropped. 3

4 Protocol (8 bits): This indicates the Transport Layer protocol (TCP, UDP, or even ICMP) that the IP packet is carrying inside of it. Header Checksum (16 bits): It is very important to make sure that the header which contains addresses and other very important information is free of errors. For this, the IP header contains a checksum (that is computed using a specific method) to detect errors that may occur in the header itself (not the data of the packet). Since there are some components of the header that change as the packet travels between routers such as the Time to Live, this header checksum is recomputed at each router after modifying the header and the new checksum is used to replace the old one. Source IP Address (32 bits): Contains the IP address of the source machine. Destination IP Address (32 bits): Contains the IP address of the destination machine. Options (variable length): Allows the source machine to request specific features such as the path of routers over which the packet is to travel over. Padding (variable length): This contains no information but it is used to extend the length of the header to insure that it is a multiple of 4 bytes (or 32 bits). The following summarizes the different components in the IPv4 header IPv4, IPv5, IPv6 5 (if no options) Priority (xxx), Delay (x), Throughput (x), Reliability (x), Cost (x) ID of packet that fragment belong to (to prevent mixing frags from different packets). ID must not be reused until sufficient time has passed 100 (for example) [packet can hop over 100 routers before being discarded] 1 (ICMP), 6 (TCP), 17 (UDP), Bytes (Max rarely used because nets have their own maximums) Not used, Offset from start of Data in Dont Frag, More Frag multiples of 8 Bytes (to insure integrity of header NOT DATA). Updated when TTL is changed ? xxx.xxx.xxx.xxx xxx.xxx.xxx.xxx To request special features (security level, route to be taken by packet, ) to make header length multiple of 32 bits Example 1: 4

5 See the example on Page 589 of your textbook. Example2: Assume that a router connecting two network (Network 1 and Network 2) has received 3 un fragmented packets from Network 1 and needs to send them over Network 2. Assume the following: The headers of all packets are 20 Bytes long Length of Packet 1 (including header) is 75 Bytes Length of Packet 2 (including header) is 88 Bytes Length of Packet 3 (including header) is 127 Bytes Maximum packet length (including header) that Network 2 can carry is 48 bytes The Don t fragment Flag of Packets 1 and 3 are set to 0, while the Don t Fragment Flag of Packet 2 is set to 1. Determine the following parameters for each fragment (if fragmentation is performed) of the above 3 packets: 1) Identification, 2) More Fragments Flag, 3) Fragment Offset 4) Total Fragment Size Answer 2: First let us strip the headers from the above packets: Length of Packet 1 (without header) is 55 Bytes Length of Packet 2 (without header) is 68 Bytes Length of Packet 3 (without header) is 107 Bytes Maximum packet length (without header) that Network 2 can carry is 28 bytes Packet 1: Since the Don t Fragment flag is set to 0, so fragmentation is allowed. Since the data part of packets that Network 2 can transport is not a multiple of 8, we will have to set the data size of fragments traveling through it to be the multiple of 8 that is just smaller than 28, which is 24 Bytes (which is 3 multiples of 8). Note that we can assume any 16 bit identification number for the segmented packets. 5

6 So, Fragment Number Identification (Must be less than 65536) More Fragments Flag Fragment Offset Because ( = 0) Because ( = 24) Because ( = 48) Data Length of Fragment Total Fragment Size (Bytes) = Header + Data = 27 Packet 2: Since the Don t Fragment flag is set to 1, and the size of the packet will not fit into a packet of Network 2, the packet will be dropped and an ICMP message will be sent to the source machine. Packet 3: Since the Don t Fragment flag is set to 0, so fragmentation is allowed. Using a similar case as with Packet 1, we get: Fragment Number Identification (Must be less than 65536) More Fragments Flag Fragment Offset Because ( = 0) Because ( = 24) Because ( = 48) Because ( = 72) Because ( = 96) Data Length of Fragment Total Fragment Size (Bytes) = Header + Data = 31 6