Figure 1 Network Topology
|
|
- Iris Webb
- 5 years ago
- Views:
Transcription
1 i Intelepeer SIP Trunking: Connecting Cisco Unified Communications Manager [v12.0.1] to Intelepeer SIP Trunks via Cisco Unified Border Element v [IOS-XE ] January 24, 2019 Page 1 of 56
2 Table of Contents Introduction... 4 Network Topology... 5 System Components... 6 Hardware Requirements... 6 Software Requirements... 6 Features... 6 Features Supported... 6 Features Not Supported... 6 Caveats... 6 Configuration... 7 Configuring Cisco Unified Border Element... 7 Network Interface... 7 Global Cisco UBE settings Codecs Dial Peer Configuration example Configuring Cisco UCM Cluster Cisco UCM Version Cisco Call Manager Service Parameters SIP Trunk Security Profile SIP Profile Trunk configuration Routing configuration Configuring Cisco Voice Gateway for Fax Global Settings Codecs Dial Peer POTS and Port Configuration Acronyms Important Information Page 2 of 56
3 Table of Figures Figure 1 Network Topology... 5 Figure 2 High Availability topology... 7 Figure 3: Cisco UCM Version Figure 4: Service Parameters Figure 5: SIP Trunk Security Profile Figure 6: SIP Profile Figure 7: SIP Profile (Cont.) Figure 8: SIP Profile (Cont.) Figure 9: SIP Profile (Cont.) Figure 10: Add New Trunk to Cisco UBE Figure 11: Add SIP Trunk Type Figure 12: SIP Trunk to Cisco UBE Figure 13: SIP Trunk to Cisco UBE (Cont.) Figure 14: SIP Trunk to Cisco UBE (Cont.) Figure 15: SIP Trunk to Cisco UBE (Cont.) Figure 16: Add New Trunk to Fax Gateway Figure 17: Add SIP Trunk Type Figure 18: SIP Trunk to Fax Gateway Figure 19: SIP Trunk to Fax Gateway (Cont.) Figure 20: SIP Trunk to Fax Gateway (Cont.) Figure 21: SIP Trunk to Fax Gateway (Cont.) Figure 22: Add New Route Pattern for Cisco UBE Figure 23: Route Pattern Configuration for Cisco UBE-PSTN Access Figure 24: Route Pattern Configuration for Cisco UBE-PSTN Access (Cont.) Figure 25 Route Pattern Configuration for Cisco UBE-PSTN Access National- Anonymous Call Figure 26: Route Pattern Configuration for Cisco UBE-PSTN Access National- Anonymous Call (Cont.) Figure 27: Add New Route patter to Fax Gateway Figure 28: Route Pattern Configuration for Fax Gateway Figure 29: Route Pattern Configuration for Fax Gateway (Cont.) Page 3 of 56
4 Introduction Service Providers today, such as Intelepeer, are offering alternative methods to connect to the PSTN via their IP network. Most of these services utilize SIP as the primary signaling method and centralized IP to TDM POP gateways to provide on-net and off-net services. Intelepeer is a service provider offering that allows connection to the PSTN and may offer the end customer a viable alternative to traditional PSTN connectivity. A demarcation device between these services and customer owned services is recommended. As an intermediary device between Cisco Unified Communications Manager (Cisco UCM) and Intelepeer network, Cisco Unified Border Element (Cisco UBE) ISR 4321/K9 running IOS-XE can be used. The Cisco Unified Border Element v12.2 provides demarcation, security, interworking and session control services for Cisco Unified Communications Manager connected to Intelepeer IP network. This document assumes the reader is knowledgeable with the terminology and configuration of Cisco Unified Communications Manager. Only configuration settings specifically required for Intelepeer interoperability are presented. Feature configuration and most importantly the dial plan are customer specific and need individual approach. This application note describes how to configure Cisco UCM , and Cisco UBE on ISR 4321/K9 [IOS-XE ] for connectivity to Intelepeer SIP Trunking service. The deployment model covered in this application note is CPE (Cisco UCM) to PSTN (Intelepeer) via Cisco UBE v [IOS- XE] Testing was performed in accordance to Intelepeer generic SIP Trunking test methodology and among features verified were basic calls, DTMF transport, Music on Hold (MOH), unattended and attended transfers, call forward, conferences and High Availability. The Cisco UBE configuration detailed in this document is based on a lab environment with a simple dial-plan used to ensure proper interoperability between Intelepeer SIP network and Cisco Unified Communications. The configuration described in this document details the important configuration settings to have enabled for interoperability to be successful and care must be taken by the network administrator deploying Cisco UCM to interoperate to Intelepeer SIP Trunking network. Page 4 of 56
5 Network Topology Figure 1 Network Topology The network topology includes the Cisco UCM Cluster, Unity Voic system, Cisco Fax gateway and 2 Cisco Endpoints. Cisco UCM has a trunk configured to Cisco UBE s Virtual IP Address. Intelepeer was used as the service provider with SIP trunk to the Cisco UBE using the WAN Virtual IP Address. 2 Cisco Unified Border Elements are used here for High Availability. SIP Trunk transport type used between Cisco UBE and Cisco UCM is UDP and to Intelepeer is UDP. Cisco UCM and Cisco UBE Settings: Setting Transport from Cisco UBE to Cisco UCM Transport from Cisco UBE to Intelepeer Voice Mail Support Session Refresh Value UDP with RTP UDP with RTP YES YES Page 5 of 56
6 System Components Hardware Requirements Cisco UBE on Cisco ISR 4321/K9 router CUCM cluster on UCS C240, 1 Publisher node, 2 Subscriber nodes and Cisco Unity Connection Cisco 2851 with FXS ports and Analog Fax machine Generic Cisco IP-Phones: 7841 and 7941 Software Requirements CUBE-Version: running IOS-XE CUCM UCOS for 1 Publisher and 2 Subscriber Cisco Unity Connection Cisco IOS v15.0(1) for the fax gateway Features Features Supported Incoming and outgoing calls using G711ulaw and G729 codecs International Calls and digit manipulations Call Conference CPE Voice Mail support Call hold & Resume with and without MoH Unattended and Attended Call transfer Call forward (all, busy and no answer) DTMF (RFC2833) Fax (T38 and G711 Pass-through) IP-PBX Calling number privacy High Availability Features Not Supported Cisco UCM does not support Blind Call transfer In HA Redundancy mode, the Primary Cisco UBE will not take over the Primary/Active role after a reboot/network outage Caveats Caller ID is not updated on attended and unattended transfer scenarios. Only one IP PBX used for the testing. The Cisco UBE HA tested is layer 2 box to box Cisco UBE redundancy. Intelepeer has negotiated the fax rate only on G3 speed. However on T.38 Loop back scenarios the fax rate was on SG3 speed. Page 6 of 56
7 Configuration Configuring Cisco Unified Border Element Network Interface The IP address used are for illustration only, the actual IP address can vary. The Active/Standby pair share the same virtual IP address and continually exchange status messages. Figure 2 High Availability topology Page 7 of 56
8 Cisco UBE 1: interface GigabitEthernet0/0/0 description Intelepeer CUBE LAN ip address negotiation auto redundancy rii 4 redundancy group 2 ip exclusive interface GigabitEthernet0/0/1 description Intelepeer CUBE WAN ip address xx.xx negotiation auto redundancy rii 3 redundancy group 2 ip xx.xx exclusive interface GigabitEthernet0/1/0 description Intelepeer CUBE HA ip address negotiation auto interface GigabitEthernet0 vrf forwarding Mgmt-intf no ip address shutdown negotiation auto Cisco UBE 2: interface GigabitEthernet0/0/0 description Intelepeer CUBE LAN ip address negotiation auto redundancy rii 4 redundancy group 2 ip exclusive Page 8 of 56
9 interface GigabitEthernet0/0/1 description Intelepeer CUBE WAN ip address xx.xx negotiation auto redundancy rii 3 redundancy group 2 ip xx.xx exclusive interface GigabitEthernet0/1/0 description Intelepeer CUBE HA ip address negotiation auto interface GigabitEthernet0 vrf forwarding Mgmt-intf no ip address shutdown negotiation auto Page 9 of 56
10 Global Cisco UBE settings In order to enable Cisco UBE IP2IP SBC functionality, following command has to be entered: voice service voip no ip address trusted authenticate address-hiding mode border-element license capacity 20 allow-connections sip to sip redundancy-group 2 sip rel1xx supported "rel100" session refresh asserted-id pai privacy pstn early-offer forced midcall-signaling passthru g729 annexb-all Explanation Command allow-connections sip to sip redundancy-group 1 asserted-id midcall-signaling passthru Description Allow IP2IP connections between two SIP call legs Enable High Availability for the VoIP service Specifies the privacy header in the outgoing SIP requests and response messages Pass-through media change method optimizes or consumes midcall, media-related signaling within the call Page 10 of 56
11 Codecs G711ulaw and G729 voice codecs are used for this testing. Codec preferences used to change according to the test plan description. voice class codec 1 codec preference 1 g729r8 codec preference 2 g711ulaw codec preference 3 g711alaw voice class codec 2 codec preference 1 g711ulaw codec preference 2 g711alaw codec preference 3 g729r8 Dial Peer Outbound Dial-peer to Intelepeer: dial-peer voice 1 voip description Ingress CUCM to PSTN - LAN Interface huntstop session protocol sipv2 session transport udp incoming called-number.t incoming uri via cucm voice-class codec 1 voice-class sip bind control source-interface GigabitEthernet0/0/0 voice-class sip bind media source-interface GigabitEthernet0/0/0 dtmf-relay rtp-nte fax protocol t38 version 0 ls-redundancy 0 hs-redundancy 0 fallback none no vad dial-peer voice 2 voip Page 11 of 56
12 description Egress CUCM to PSTN - WAN Interface huntstop destination-pattern.t session protocol sipv2 session target ipv4:68.68.xx.xx:5060 session transport udp voice-class codec 1 voice-class sip bind control source-interface GigabitEthernet0/0/1 voice-class sip bind media source-interface GigabitEthernet0/0/1 dtmf-relay rtp-nte fax rate fax protocol t38 version 0 ls-redundancy 0 hs-redundancy 0 fallback none no vad Inbound Dial-peer from Intelepeer: dial-peer voice 3 voip description Ingress PSTN to CUCM - WAN Interface huntstop session protocol sipv2 session transport udp incoming called-number voice-class codec 1 voice-class sip bind control source-interface GigabitEthernet0/0/1 voice-class sip bind media source-interface GigabitEthernet0/0/1 dtmf-relay rtp-nte fax protocol t38 version 0 ls-redundancy 0 hs-redundancy 0 fallback none no vad dial-peer voice 4 voip description Egress PSTN to CUCM - LAN Interface huntstop destination-pattern session protocol sipv2 session target ipv4: :5060 Page 12 of 56
13 session transport udp voice-class codec 1 voice-class sip bind control source-interface GigabitEthernet0/0/0 voice-class sip bind media source-interface GigabitEthernet0/0/0 dtmf-relay rtp-nte fax protocol t38 version 0 ls-redundancy 0 hs-redundancy 0 fallback none no vad Page 13 of 56
14 Configuration example The following configuration snippet contains a sample configuration of Cisco UBE with all parameters mentioned previously. Active Cisco UBE: version 16.9 service timestamps debug datetime msec service timestamps log datetime msec platform qfp utilization monitor load 80 no platform punt-keepalive disable-kernel-core hostname IntelepeerCUBE1 boot-start-marker boot system flash isr4300-universalk spa.bin boot-end-marker vrf definition Mgmt-intf address-family ipv4 exit-address-family address-family ipv6 exit-address-family enable secret 5 $1$nU no aaa new-model ip admission watch-list expiry-time 0 subscriber templating multilink bundle-name authenticated Page 14 of 56
15 voice service voip no ip address trusted authenticate address-hiding mode border-element license capacity 20 allow-connections sip to sip redundancy-group 2 sip rel1xx supported "rel100" session refresh asserted-id pai privacy pstn early-offer forced midcall-signaling passthru g729 annexb-all voice class uri cucm sip host voice class codec 1 codec preference 1 g729r8 codec preference 2 g711ulaw codec preference 3 g711alaw voice class codec 2 codec preference 1 g711ulaw codec preference 2 g711alaw codec preference 3 g729r8 license udi pid ISR4321/K9 sn FDO19220MSQ Page 15 of 56
16 license accept end user agreement license boot suite AdvUCSuiteK9 license boot level appxk9 license boot level securityk9 no license smart enable diagnostic bootup level minimal spanning-tree extend system-id username **** privilege 15 password 0 ****** redundancy mode none application redundancy group 2 name IntelepeerB2BHA priority 100 failover threshold 75 timers delay 30 reload 60 control GigabitEthernet0/1/0 protocol 1 data GigabitEthernet0/1/0 track 1 shutdown track 2 shutdown track 1 interface GigabitEthernet0/0/0 line-protocol track 2 interface GigabitEthernet0/0/1 line-protocol interface GigabitEthernet0/0/0 description Intelepeer CUBE LAN Page 16 of 56
17 ip address negotiation auto redundancy rii 4 redundancy group 2 ip exclusive interface GigabitEthernet0/0/1 description Intelepeer CUBE WAN ip address xx.xx negotiation auto redundancy rii 3 redundancy group 2 ip xx.xx exclusive interface GigabitEthernet0/1/0 description Intelepeer CUBE HA ip address negotiation auto interface GigabitEthernet0 vrf forwarding Mgmt-intf no ip address shutdown negotiation auto ip forward-protocol nd no ip http server no ip http secure-server ip tftp source-interface GigabitEthernet0 ip route xx.xx ip route Page 17 of 56
18 ip route control-plane mgcp behavior rsip-range tgcp-only mgcp behavior comedia-role none mgcp behavior comedia-check-media-src disable mgcp behavior comedia-sdp-force disable mgcp profile default dial-peer voice 1 voip description Ingress CUCM to PSTN - LAN Interface huntstop session protocol sipv2 session transport udp incoming called-number.t incoming uri via cucm voice-class codec 1 voice-class sip bind control source-interface GigabitEthernet0/0/0 voice-class sip bind media source-interface GigabitEthernet0/0/0 dtmf-relay rtp-nte fax protocol t38 version 0 ls-redundancy 0 hs-redundancy 0 fallback none no vad dial-peer voice 2 voip description Egress CUCM to PSTN - WAN Interface huntstop destination-pattern.t Page 18 of 56
19 session protocol sipv2 session target ipv4:68.68.xx.xx:5060 session transport udp voice-class codec 1 voice-class sip bind control source-interface GigabitEthernet0/0/1 voice-class sip bind media source-interface GigabitEthernet0/0/1 dtmf-relay rtp-nte fax rate fax protocol t38 version 0 ls-redundancy 0 hs-redundancy 0 fallback none no vad dial-peer voice 3 voip description Ingress PSTN to CUCM - WAN Interface huntstop session protocol sipv2 session transport udp incoming called-number voice-class codec 1 voice-class sip bind control source-interface GigabitEthernet0/0/1 voice-class sip bind media source-interface GigabitEthernet0/0/1 dtmf-relay rtp-nte fax protocol t38 version 0 ls-redundancy 0 hs-redundancy 0 fallback none no vad dial-peer voice 4 voip description Egress PSTN to CUCM - LAN Interface huntstop destination-pattern session protocol sipv2 Page 19 of 56
20 session target ipv4: :5060 session transport udp voice-class codec 1 voice-class sip bind control source-interface GigabitEthernet0/0/0 voice-class sip bind media source-interface GigabitEthernet0/0/0 dtmf-relay rtp-nte fax protocol t38 version 0 ls-redundancy 0 hs-redundancy 0 fallback none no vad line con 0 exec-timeout 0 0 password ****** login local transport input none stopbits 1 line aux 0 stopbits 1 line vty 0 4 exec-timeout 0 0 password ****** login local end Page 20 of 56
21 Standby Cisco UBE: version 16.9 service timestamps debug datetime msec service timestamps log datetime msec platform qfp utilization monitor load 80 no platform punt-keepalive disable-kernel-core hostname IntelepeerCUBE2 boot-start-marker boot system flash:isr4300-universalk spa.bin boot-end-marker vrf definition Mgmt-intf address-family ipv4 exit-address-family address-family ipv6 exit-address-family enable secret 5 $1$u no aaa new-model ip admission watch-list expiry-time 0 subscriber templating multilink bundle-name authenticated Page 21 of 56
22 voice service voip no ip address trusted authenticate address-hiding mode border-element license capacity 20 allow-connections sip to sip redundancy-group 2 sip rel1xx supported "rel100" session refresh asserted-id pai privacy pstn early-offer forced midcall-signaling passthru g729 annexb-all voice class uri cucm sip host voice class codec 1 codec preference 1 g729r8 codec preference 2 g711ulaw codec preference 3 g711alaw voice class codec 2 codec preference 1 g711ulaw codec preference 2 g711alaw codec preference 3 g729r8 license udi pid ISR4321/K9 sn FDO19220MQ9 license accept end user agreement Page 22 of 56
23 license boot suite AdvUCSuiteK9 license boot level appxk9 license boot level uck9 license boot level securityk9 no license smart enable diagnostic bootup level minimal spanning-tree extend system-id username **** privilege 15 password 0 ****** redundancy mode none application redundancy group 2 name IntelepeerB2BHA priority 100 failover threshold 75 timers delay 30 reload 60 control GigabitEthernet0/1/0 protocol 1 data GigabitEthernet0/1/0 track 1 shutdown track 2 shutdown track 1 interface GigabitEthernet0/0/0 line-protocol track 2 interface GigabitEthernet0/0/1 line-protocol interface GigabitEthernet0/0/0 description Intelepeer CUBE LAN Page 23 of 56
24 ip address negotiation auto redundancy rii 4 redundancy group 2 ip exclusive interface GigabitEthernet0/0/1 description Intelepeer CUBE WAN ip address xx.xx negotiation auto redundancy rii 3 redundancy group 2 ip xx.xx exclusive interface GigabitEthernet0/1/0 description Intelepeer CUBE HA ip address negotiation auto interface GigabitEthernet0 vrf forwarding Mgmt-intf no ip address shutdown negotiation auto ip forward-protocol nd ip http server ip http secure-server ip tftp source-interface GigabitEthernet0 ip route xx.xx ip route Page 24 of 56
25 ip route control-plane mgcp behavior rsip-range tgcp-only mgcp behavior comedia-role none mgcp behavior comedia-check-media-src disable mgcp behavior comedia-sdp-force disable mgcp profile default dial-peer voice 1 voip description Ingress CUCM to PSTN - LAN Interface huntstop session protocol sipv2 session transport udp incoming called-number.t incoming uri via cucm voice-class codec 1 voice-class sip bind control source-interface GigabitEthernet0/0/0 voice-class sip bind media source-interface GigabitEthernet0/0/0 dtmf-relay rtp-nte fax protocol t38 version 0 ls-redundancy 0 hs-redundancy 0 fallback none no vad dial-peer voice 2 voip description Egress CUCM to PSTN - WAN Interface huntstop Page 25 of 56
26 destination-pattern.t session protocol sipv2 session target ipv4:68.68.xx.xx:5060 session transport udp voice-class codec 1 voice-class sip bind control source-interface GigabitEthernet0/0/1 voice-class sip bind media source-interface GigabitEthernet0/0/1 dtmf-relay rtp-nte fax rate fax protocol t38 version 0 ls-redundancy 0 hs-redundancy 0 fallback none no vad dial-peer voice 3 voip description Ingress PSTN to CUCM - WAN Interface huntstop session protocol sipv2 session transport udp incoming called-number voice-class codec 1 voice-class sip bind control source-interface GigabitEthernet0/0/1 voice-class sip bind media source-interface GigabitEthernet0/0/1 dtmf-relay rtp-nte fax protocol t38 version 0 ls-redundancy 0 hs-redundancy 0 fallback none no vad dial-peer voice 4 voip description Egress PSTN to CUCM - LAN Interface huntstop destination-pattern Page 26 of 56
27 session protocol sipv2 session target ipv4: :5060 session transport udp voice-class codec 1 voice-class sip bind control source-interface GigabitEthernet0/0/0 voice-class sip bind media source-interface GigabitEthernet0/0/0 dtmf-relay rtp-nte fax protocol t38 version 0 ls-redundancy 0 hs-redundancy 0 fallback none no vad gateway timer receive-rtp 1200 line con 0 exec-timeout 0 0 transport input none stopbits 1 line aux 0 stopbits 1 line vty 0 4 login local transport input telnet end Page 27 of 56
28 Configuring Cisco UCM Cluster Cisco UCM Version Figure 3: Cisco UCM Version Page 28 of 56
29 Cisco Call Manager Service Parameters Navigation: System Service Parameters Select Server* = Clus20pub--CUCM Voice/Video (Active) Select Service*= Cisco CallManager (Active) All other fields are set to default values Figure 4: Service Parameters SIP Trunk Security Profile Navigation: System Security SIP Trunk Security Profile Name*= Non Secure SIP Trunk Profile for Intelepeer is used as an example Description = Non Secure SIP Trunk Profile Intelepeer is used as an example Device Security Mode = Non Secure Incoming Transport Type* = TCP + UDP Outgoing Transport Type = UDP Page 29 of 56
30 Figure 5: SIP Trunk Security Profile Page 30 of 56
31 SIP Profile Navigation: Device Device Settings SIP Profile Name*= Standard SIP Profile for Intelepeer is used as an example SIP Rel1XX Options: Send PRACK if 1XX contains SDP is selected for this example Figure 6: SIP Profile Page 31 of 56
32 Figure 7: SIP Profile (Cont.) Page 32 of 56
33 Figure 8: SIP Profile (Cont.) Page 33 of 56
34 Figure 9: SIP Profile (Cont.) Page 34 of 56
35 Trunk configuration Trunk configuration from Cisco UCM to the LAN side of the Cisco UBE: Navigation: Device Trunk Add New Figure 10: Add New Trunk to Cisco UBE Select Trunk Type as SIP Trunk and Device Protocol as SIP and select Next as shown below. Set Device Name: Intelepeer_SIP_trunk_to_CUBE is given for this example Set Description: Intelepeer SIP trunk to CUBE is given for this example Select Device Pool: Intelepeer G711Ulaw is selected for this example. Set Significant Digits: 4 Under Destination: Set Destination Address: is given for this example. This is the CUBE LAN side VIP IP address. Set Destination Port: 5060 Set BLF Presence Group: Standard presence group is selected from dropdown menu Set SIP Trunk security profile: Non Secured SIP Trunk Profile for Intelepeer is selected from drop down menu Set SIP Profile: Standard SIP Profile for Intelepeer is selected from drop down menu Page 35 of 56
36 Figure 11: Add SIP Trunk Type Page 36 of 56
37 Figure 12: SIP Trunk to Cisco UBE Page 37 of 56
38 Figure 13: SIP Trunk to Cisco UBE (Cont.) Configure the Virtual LAN IP address of the Cisco UBE and the Destination Port Configure the SIP Trunk Security Profile and SIP Profile as shown below The rest of the configuration is all default Click Save and Reset after completion Page 38 of 56
39 Figure 14: SIP Trunk to Cisco UBE (Cont.) Page 39 of 56
40 Figure 15: SIP Trunk to Cisco UBE (Cont.) Page 40 of 56
41 Trunk configuration from Cisco UCM to Fax Gateway: Navigation: Device Trunk Add New Figure 16: Add New Trunk to Fax Gateway Select Trunk Type as SIP Trunk and Device Protocol as SIP and select Next as shown below. Set Device Name: FaxGatewayIntelepeer is given for this example Set Description: faxgateway is given for this example Select Device Pool: Intelepeer G711Ulaw is selected for this example. Set Significant Digits: All Under Destination: Set Destination Address: is given for this example. This is the Fax gateway IP address. Set Destination Port: 5060 Set BLF Presence Group: Standard presence group is selected from dropdown menu Set SIP Trunk security profile: Non Secured SIP Trunk Profile for Intelepeer is selected from drop down menu Set SIP Profile: Standard SIP Profile for Intelepeer is selected from drop down menu Page 41 of 56
42 Figure 17: Add SIP Trunk Type Figure 18: SIP Trunk to Fax Gateway Page 42 of 56
43 Figure 19: SIP Trunk to Fax Gateway (Cont.) Configure the IP address of the Fax gateway and the Destination Port Configure the SIP Trunk Security Profile and SIP Profile as shown below The rest of the configuration is all default Click Save and Reset after completion Page 43 of 56
44 Figure 20: SIP Trunk to Fax Gateway (Cont.) Page 44 of 56
45 Figure 21: SIP Trunk to Fax Gateway (Cont.) Page 45 of 56
46 Routing configuration Route Pattern for Cisco UBE: Navigation: Call Routing Route/Hunt Route Pattern Add New Figure 22: Add New Route Pattern for Cisco UBE Page 46 of 56
47 Figure 23: Route Pattern Configuration for Cisco UBE-PSTN Access Page 47 of 56
48 Figure 24: Route Pattern Configuration for Cisco UBE-PSTN Access (Cont.) Figure 25 Route Pattern Configuration for Cisco UBE-PSTN Access National- Anonymous Call Page 48 of 56
49 Figure 26: Route Pattern Configuration for Cisco UBE-PSTN Access National- Anonymous Call (Cont.) Page 49 of 56
50 Route Pattern for Fax Gateway: Navigation: Call Routing Route/Hunt Route Pattern Add New Figure 27: Add New Route patter to Fax Gateway Figure 28: Route Pattern Configuration for Fax Gateway Page 50 of 56
51 Figure 29: Route Pattern Configuration for Fax Gateway (Cont.) Page 51 of 56
52 Configuring Cisco Voice Gateway for Fax Global Settings voice service voip allow-connections sip to sip no supplementary-service sip handle-replaces redirect ip2ip fax protocol t38 version 0 ls-redundancy 0 hs-redundancy 0 fallback none no fax-relay sg3-to-g3 sip midcall-signaling passthru g729 annexb-all Codecs G711ulaw and G729 voice codecs are used for this testing. Codec preferences used to change according to the test plan description. voice class codec 1 codec preference 1 g729r8 codec preference 2 g711ulaw codec preference 3 g711alaw voice class codec 2 codec preference 1 g711ulaw codec preference 2 g711alaw codec preference 3 g729r8 Dial Peer Inbound Dial-peer from Cisco UCM: Page 52 of 56
53 dial-peer voice 4500 voip description Inbound DP for CUCM-FAX session protocol sipv2 session target sip-server session transport udp incoming called-number x. voice-class codec 1 dtmf-relay rtp-nte fax protocol t38 version 0 ls-redundancy 0 hs-redundancy 0 fallback none no vad Outbound Dial-peer to Cisco UCM: dial-peer voice 4501 voip description Outbound DP for CUCM-FAX destination-pattern 8. session protocol sipv2 session target ipv4: :5060 session transport udp voice-class codec 1 dtmf-relay rtp-nte fax protocol t38 version 0 ls-redundancy 0 hs-redundancy 0 fallback none no vad POTS and Port Configuration Based on configured POTS destination pattern, gateway forwards the call to designated voice port. dial-peer voice 4502 pots service session destination-pattern xx no digit-strip port 0/0/0 forward-digits all Page 53 of 56
54 voice-port 0/0/0 no echo-cancel enable no vad cptone IN description Fax Test-Intelepeer station-id number xx caller-id enable Page 54 of 56
55 Acronyms Acronym CPE Cisco UBE Cisco UCM MTP POP PSTN ESBC SCCP SIP Definitions Customer Premise Equipment Cisco Unified Border Element Cisco Unified Communications Manager Media Termination Point Point of Presence Public Switched Telephone Network Enterprise Session Border Controller Skinny Client Control Protocol Session Initiation Protocol Important Information THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS. IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING, WITHOUT LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES Page 55 of 56
56 Corporate Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA USA Tel: NETS (6387) Fax: European Headquarters CiscoSystems International BV Haarlerbergpark Haarlerbergweg CH Amsterdam The Netherlands wwweurope.cisco.com Tel: Fax: Americas Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA USA Tel: Fax: AsiaPacific Headquarters Cisco Systems, Inc. Capital Tower 168 Robinson Road #22-01 to #29-01 Singapore Tel: Fax: Cisco Systems has more than 200 offices in the following countries and regions. Addresses, phone numbers, and fax numbers are listed on the Cisco Web site at Argentina Australia Austria Belgium Brazil Bulgaria Canada Chile China PRC Colombia Costa Rica Croatia Czech Republic Denmark Dubai, UAE Finland France Germany Greece Hong Kong SAR Hungary India Indonesia Ireland Israel Italy Japan Korea Luxembourg Malaysia Mexico The Netherlands New Zealand Norway Peru Philippines Poland Portugal Puerto Rico Romania Russia Saudi Arabia Scotland Singapore Slovakia Slovenia South Africa Spain Sweden Switzerland Taiwan Thailand Turkey Ukraine United Kingdom United States Venezuela Vietnam Zimbabwe 2016 Cisco Systems, Inc. All rights reserved. CCENT, Cisco Lumin, Cisco Nexus, the Cisco logo and the Cisco Square Bridge logo are trademarks of Cisco Systems, Inc.; Changing the Way We Work, Live, Play, and Learn is a service mark of Cisco Systems, Inc.; and Access Registrar, Aironet, BPX, Catalyst, CCDA, CCDP, CCVP, CCIE, CCIP, CCNA, CCNP, CCSP, Cisco, the Cisco Certified Internetwork Expert logo, Cisco IOS, Cisco Press, Cisco Systems, Cisco Systems Capital, the Cisco Systems logo, Cisco Unity, EtherFast, EtherSwitch, Fast Step, Follow Me Browsing, FormShare, GigaDrive, HomeLink, Internet Quotient, IOS, iphone, iq Expertise, the iq logo, iq Net Readiness Scorecard, iquick Study, LightStream, Linksys, Meeting Place, MGX, Networking Academy, Network Registrar, Packet, PIX, ProConnect, ScriptShare, SMARTnet, StackWise, The Fastest Way to Increase Your Internet Quotient, and TransPath are registered trademarks of Cisco Systems, Inc. and/or its affiliates in the United States and certain other countries. All other trademarks mentioned in this document or Website are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (0705R) Printed in the USA Page 56 of 56
Using TAPS with +E.164 Directory Numbers
Application Note Using TAPS with +E.164 Directory Numbers Page 1 of 8 Rev 1.1 September 17, 2010 Revision 1.1 Table of Contents INTRODUCTION 2 INSTALLING CISCO UNIFIED CONTACT CENTER EXPRESS 2 INSTALLING
More informationCisco 2651XM Gateway - PBX Interoperability: Avaya Definity G3 PBX using Analog FXO Interfaces to an H.323 Gateway
Application Note Cisco 2651XM Gateway - PBX Interoperability: Avaya Definity G3 PBX using Analog FXO Interfaces to an H.323 Gateway Introduction This note describes the interoperability between the Avaya
More informationCisco Unified Communications Manager with Cisco Unified Border Element (CUBE ) on ISR4321 [IOS-XE ] using SIP
Fusion Connect SIP Trunking: Application Note Cisco Unified Communications Manager 11.5.1 with Cisco Unified Border Element (CUBE 11.5.2) on ISR4321 [IOS-XE 16.3.1] using SIP October 2016 Page 1 of 51
More informationCisco Unity 4.0(4) with Cisco Unified CallManager 4.1(2) Configured as Message Center PINX using Cisco WS-X6608-T1 using Q.SIG as MGCP Gateway
Application Note Cisco Unity 4.0(4) with Cisco Unified CallManager 4.1(2) Configured as Message Center PINX using Cisco WS-X6608-T1 using Q.SIG as MGCP Gateway November 2, 2007 Revision 5 Table of Contents
More informationCONFIGURING EPOLICY ORCHESTRATOR 3.0 AND MCAFEE 8.0i WITH CISCO CALLMANAGER
PRODUCT BULLETIN NO. 2866 CONFIGURING EPOLICY ORCHESTRATOR 3.0 AND MCAFEE 8.0i WITH CISCO CALLMANAGER Cisco CallManager runs on a Windows2000 server. An important administrative task for server management
More informationCisco Unified Communications Manager with Cisco Unified Border Element (CUBE ) on ISR4321/K9 [IOS- XE
Comcast SIP Trunking: Application Note Cisco Unified Communications Manager 10.5.2 with Cisco Unified Border Element (CUBE 11.5.0) on ISR4321/K9 [IOS- XE 3.17.1 15.6(1)S1] using SIP July 2016 Page 1 of
More informationCisco Unified Communications Manager with Cisco Unified Border Element (CUBE ) on ISR 4K [IOS-XE 3.16] using SIP
Application Note Cox SIP Trunking: Cisco Unified Communications Manager 11.0.1 with Cisco Unified Border Element (CUBE 11.1.0) on ISR 4K [IOS-XE 3.16] using SIP November 11, 2015 Page 1 of 57 Table of
More informationCISCO FAX SERVER. Figure 1. Example Deployment Scenario. The Cisco Fax Server solution consists of the following components:
DATA SHEET CISCO FAX SERVER The Cisco Fax Server is an easy-to-use, easy-to-manage fax and e-document delivery solution that helps enterprises integrate voice, fax, data, and desktop applications for powerful
More informationCisco Unified Communications Manager with Cisco Unified Border Element (CUBE ) on ISR 4321 [IOS-XE (1)S, 3.
TalkTalk SIP Trunking: Cisco Unified Communications Manager 11.0.1 with Cisco Unified Border Element (CUBE 11.5.0) on ISR 4321 [IOS-XE - 15.6(1)S, 3.17] using SIP March 7, 2016 Page 1 of 70 Table of Contents
More informationCisco Unified CallConnector for Microsoft Office Quick Reference Guide 1
Quick Reference Cisco Unified CallConnector for Microsoft Office Quick Reference Guide 1 Overview 2 Starting and Accessing Features 3 Using the Call Popup Window 4 Using QuickSearch 5 Toolbar Overview
More informationNEW METHOD FOR ORDERING CISCO 1700 SERIES MODULAR ACCESS ROUTERS AND CISCO 1800 SERIES INTEGRATED SERVICES ROUTERS SOFTWARE SPARE IMAGES
PRODUCT BULLETIN, NO. 2748 NEW METHOD FOR ORDERING CISCO 1700 SERIES MODULAR ACCESS ROUTERS AND CISCO 1800 SERIES INTEGRATED SERVICES ROUTERS SOFTWARE SPARE IMAGES Until recently, every release of Cisco
More informationCisco CallManager 4.0-PBX Interoperability: Lucent/Avaya Definity G3 MV1.3 PBX using 6608-T1 PRI NI2 with MGCP
Application Note Cisco CallManager 4.0-PBX Interoperability: Lucent/Avaya Definity G3 MV1.3 PBX using 6608-T1 PRI NI2 with MGCP Introduction This is an application note for connectivity of Lucent/Avaya
More informationCISCO SFP OPTICS FOR PACKET-OVER-SONET/SDH AND ATM APPLICATIONS
DATA SHEET CISCO SFP OPTICS FOR PACKET-OVER-SONET/SDH AND ATM APPLICATIONS The Cisco industry-standard Small Form-Factor Pluggable Interface Converter (SFP) for packet-over-sonet/sdh (POS), optical networking,
More informationCisco Unified Communications Manager with Cisco Unified Border Element (CUBE ) on ISR 4321 [IOS-XE
IntelePeer SIP Trunking: Cisco Unified Communications Manager 11.0.1 with Cisco Unified Border Element (CUBE 11.5.0) on ISR 4321 [IOS-XE 3.17 15.6(1)S] using SIP May 20, 2016 Page 1 of 47 Table of Contents
More informationCisco Unified Communications Manager with Cisco Unified Border Element (CUBE ) on ISR 4321 [IOS-XE
Sprint SIP Trunking: Cisco Unified Communications Manager 11.5.1 with Cisco Unified Border Element (CUBE 12.0.0) on ISR 4321 [IOS-XE 16.06.01] using SIP October 25, 2017 Page 1 of 36 Table of Contents
More informationCisco 3745 Gateway - PBX Interoperability: Avaya Definity G3 PBX using Q.931 PRI Network Side Interfaces to an H.323 Gateway
Application Note Cisco 3745 Gateway - PBX Interoperability: Avaya Definity G3 PBX using Q.931 PRI Network Side Interfaces to an H.323 Gateway Introduction This Application Note describes the interoperability
More informationUSING MCAFEE VIRUSSCAN ENTERPRISE 8.0I WITH CISCO CALLMANAGER
APPLICATION NOTE USING MCAFEE VIRUSSCAN ENTERPRISE 8.0I WITH CISCO CALLMANAGER Cisco Systems does not formally certify antivirus products with Cisco CallManager software. However, the company recognizes
More informationConnecting Cisco Unified Communication Manager [v12.0.1] to Cox Business SIP Trunks via Cisco Unified Border Element v12.0 [IOS- XE
Connecting Cisco Unified Communication Manager [v12.0.1] to Cox Business SIP Trunks via Cisco Unified Border Element v12.0 [IOS- XE 16.06.01] January 24, 2018 Page 1 of 73 Table of Contents Introduction...
More informationConnecting Cisco Unified Communication Manager [v11.5.1] to CenturyLink IQ SIP Trunks via Cisco Unified Border Element v [IOS-XE 16.3.
Connecting Cisco Unified Communication Manager [v11.5.1] to CenturyLink IQ SIP Trunks via Cisco Unified Border Element v11.5.2 [IOS-XE 16.3.2] May 3, 2017 Page 1 of 70 Table of Contents Introduction...
More informationAvaya Definity CM 2.0 to a Cisco IAD243X using PRI T1 5ESS ISDN with SIP
Application Note Avaya Definity CM 2.0 to a Cisco IAD243X using PRI T1 5ESS ISDN with SIP January 5, 2007 Initial Version Table of Contents Introduction...1 Network Topology...2 Limitations...2 Hardware
More informationCisco Unified Communications Manager with Cisco Unified Border Element (CUBE ) on ISR 4331 [IOS-XE
Cebod Telecom SIP Trunking: Cisco Unified Communications Manager 12.0.1 with Cisco Unified Border Element (CUBE 12.1.0) on ISR 4331 [IOS-XE 16.08.01] using SIP September 2018 Page 1 of 61 Table of Contents
More informationCisco MDS 9000 Family and EMC ECC Integration
White Paper Cisco MDS 9000 Family and EMC ECC Integration INTRODUCTION Customers today prefer to manage their storage area network (SAN) from a centralized management application. This approach offers
More informationANNOUNCING NEW PRODUCT OFFERINGS FOR THE CISCO CATALYST 6500 SERIES
PRODUCT BULLETIN NO. 2028 ANNOUNCING NEW PRODUCT OFFERINGS FOR THE CISCO CATALYST 6500 SERIES NEW PRODUCT OFFERINGS: Cisco Catalyst 6503 Firewall Security System Cisco Catalyst 6506 Firewall Security System
More informationEND-OF-SALE AND END-OF-LIFE ANNOUNCEMENT FOR THE CISCO FLEXWAN MODULE FOR USE WITH THE CISCO 7600 SERIES ROUTERS AND CATALYST 6500 SERIES SWITCHES
PRODUCT BULLETIN NO. 2931 END-OF-SALE AND END-OF-LIFE ANNOUNCEMENT FOR THE CISCO FLEXWAN MODULE FOR USE WITH THE CISCO 7600 SERIES ROUTERS AND CATALYST 6500 SERIES SWITCHES Cisco Systems announces the
More informationCisco Unified Communications Manager with Cisco Unified Border Element (CUBE ) on ISR 4321/K9 [IOS
IntelePeer SIP Trunking: Cisco Unified Communications Manager 11.5.1 with Cisco Unified Border Element (CUBE 11.5.0) on ISR 4321/K9 [IOS - 16.5.1b] using SIP October 6, 2017 Page 1 of 57 Table of Contents
More informationUSING TREND SERVERPROTECT5 WITH CISCO CALLMANAGER
PRODUCT BULLETIN NO. 2501 USING TREND SERVERPROTECT5 WITH CISCO CALLMANAGER PRODUCT OVERVIEW Any Windows 2000 Server is recommended to have virus protection and the Cisco CallManager is no exception. Trend
More informationCisco CallManager Server Upgrade Program
Program Cisco CallManager Server Upgrade Program April 25, 2003 This program is structured to allow existing customers with either Media Convergence Servers or third-party servers running Cisco CallManager
More informationAcronyms Important Information... 71
Connecting Cisco Unified Communication Manager [v11.5.1] to British Telecom Global SIP Trunking Service via Cisco Unified Border Element v12.0 [IOS-XE 16.06.01] December 7, 2017 Page 1 of 72 Table of Contents
More informationCox SIP Trunking: Cisco Unified Communications Manager with Cisco Unified Border Element (CUBE ) on ISR4321 [IOS-XE 3.
Application Note Cox SIP Trunking: Cisco Unified Communications Manager 11.0.1 with Cisco Unified Border Element (CUBE 11.5.0) on ISR4321 [IOS-XE 3.17] using SIP April 2017 Page 1 of 86 Table of Contents
More informationCisco Unified Communications Manager with Cisco Unified Border Element (CUBE ) on ISR4321/K9 [IOS 15.6(1)S] using SIP
BroadCloud SIP Trunking: Registering Trunk Application Note Cisco Unified Communications Manager 11.0.1 with Cisco Unified Border Element (CUBE 11.5.0) on ISR4321/K9 [IOS 15.6(1)S] using SIP July 2016
More informationCisco Router and Security Device Manager Intrusion Prevention System
Application Note Cisco Router and Security Device Manager Intrusion Prevention System Introduction This document explains how to use the Cisco Router and Security Device Manager (Cisco SDM) to manage a
More informationCISCO NETWORK CONNECTIVITY CENTER BUSINESS DASHBOARD
DATA SHEET CISCO NETWORK CONNECTIVITY CENTER BUSINESS DASHBOARD The Cisco Network Connectivity Center (NCC) Business Dashboard displays the results of powerful analysis in a flexible, Web-based user interface.
More informationLevel 3 SIP Trunking: Connecting Cisco Unified Communications Manager 8.0(3) via the Cisco Unified Border Element using SIP
Application Note Level 3 SIP Trunking: Connecting Cisco Unified Communications Manager 8.0(3) via the Cisco Unified Border Element using SIP August 19, 2010 Table of Contents Introduction... 2 Network
More informationNEW CISCO IOS SOFTWARE RELEASE 12.2(25)FY FOR CISCO CATALYST EXPRESS 500 SERIES SWITCHES
PRODUCT BULLETIN NO. 3053 NEW CISCO IOS SOFTWARE RELEASE 12.2(25)FY FOR CISCO CATALYST EXPRESS 500 SERIES SWITCHES Cisco Systems is pleased to announce Cisco IOS Software for the new Cisco Catalyst Express
More informationCisco Unified CallManager Licensing Pricing Model
Q & A Cisco Unified CallManager Licensing Pricing Model Q. How is the Cisco Unified CallManager licensing pricing model changing and why? A. With the introduction of the Cisco Unified Communications family
More informationCisco Unified Wireless IP Phone 7920 Multi-Charger
Data Sheet Cisco Unified Wireless IP Phone 7920 Multi-Charger The Cisco Unified Communications system of voice and IP communications products and applications enables organizations to communicate more
More informationCISCO IOS SOFTWARE RELEASE 12.3(11)YK
PRODUCT BULLETIN NO. 2767 CISCO IOS SOFTWARE RELEASE 12.3(11)YK LIFESPAN OF RELEASE This Cisco IOS Software special release is a short-lived release and will migrate into the first release of the 12.4T
More informationCisco AS5300 Gateway - PBX Interoperability: NEC NEAX 2400 PBX using T1 PRI Interfaces to an H.323 Gateway
Application Note Cisco AS5300 Gateway - PBX Interoperability: NEC NEAX 2400 PBX using T1 PRI Interfaces to an H.323 Gateway Introduction This Application Note describes the interoperability of a Cisco
More informationCisco Unified Wireless Network Software Release 3.1
Product Bulletin No. 3050 Cisco Unified Wireless Network Software Release 3.1 Cisco Systems announces the availability of Cisco Unified Wireless Network Software Release 3.1. This release contains new
More informationMitel 3300 ICP Release 4.1 using T1 QSIG to Cisco Unified CallManager 4.0
Application Note Mitel 3300 ICP Release 4.1 using T1 QSIG to Cisco Unified CallManager 4.0 November 29, 2007 Revision 2 Table of Contents Introduction...1 Network Topology...2 Limitations...2 System Components...3
More informationCisco Unified CallManager 4.0-PBX Interoperability: Mitel 3300 ICP Release 4.1 PBX to a Cisco 6608 Gateway using T1 QSIG with MGCP
Application Note Cisco Unified CallManager 4.0-PBX Interoperability: Mitel 3300 ICP Release 4.1 PBX to a Cisco 6608 Gateway using T1 QSIG with MGCP Introduction This is an application note for connectivity
More informationAvaya Definity G3 Version CM2.0 to Cisco IOS Voice Gateway using H.323 with E1 R2
Application Note Avaya Definity G3 Version CM2.0 to Cisco IOS Voice Gateway using H.323 with E1 R2 February 02, 2008 Table of Contents Introduction...2 Network Topology...3 Limitations...3 System Components...4
More informationCISCO WDM SERIES OF CWDM PASSIVE DEVICES
DATA SHEET CISCO WDM SERIES OF CWDM PASSIVE DEVICES Cisco Systems introduces its second generation of coarse wavelength-division multiplexing (CWDM) passive devices boasting increased functions and improved
More informationCISCO CENTRALIZED WIRELESS LAN SOFTWARE RELEASE 3.0
PRODUCT BULLETIN NO. 3004 CISCO CENTRALIZED WIRELESS LAN SOFTWARE RELEASE 3.0 Cisco Systems announces the availability of Cisco Centralized Wireless LAN Software Release 3.0 for the Cisco Centralized WLAN
More informationThird party information provided to you courtesy of Dell
Third party information provided to you courtesy of Dell THE CISCO CATALYST BLADE SWITCH 3030 FOR THE DELL POWEREDGE BLADE SERVER ENCLOSURE LEVERAGE THE POWER OF CISCO S INFRASTRUCTURE SERVICES TO IMPROVE
More informationEND-OF-SALE AND END-OF-LIFE ANNOUNCEMENT FOR THE CISCO CATALYST 6500 SERIES OC-12 ATM MODULE
PRODUCT BULLETIN NO. 2628 END-OF-SALE AND END-OF-LIFE ANNOUNCEMENT FOR THE CISCO CATALYST 6500 SERIES OC-12 ATM MODULE Cisco Systems announces the end-of-sale and end-of-life dates of the Cisco Catalyst
More informationInnovation in Accessibility
Innovation in Accessibility Accessibility: Our Responsibility As we at Cisco Systems change how people work, live, play, and learn, it s essential that we ensure the same for people with disabilities.
More informationCISCO IP PHONE 7970G NEW! CISCO IP PHONE 7905G AND 7912G XML
Q & A CISCO IP PHONE 7970G NEW! CISCO IP PHONE 7905G AND 7912G XML GENERAL QUESTIONS Q. What is the Cisco IP Phone 7970G? A. The 7970G is our latest state-of-the-art IP phone, which includes a large color,
More informationCisco 7304 Shared Port Adapter Modular Services Card
Data Sheet Cisco 7304 Shared Port Adapter Modular Services Card The Cisco I-Flex design combines shared port adapters (SPAs) and SPA interface processors (SIPs), leveraging an extensible design that enables
More informationEND-OF-SALE AND END-OF-LIFE ANNOUNCEMENT FOR THE CISCO MEDIA CONVERGENCE SERVER 7845H-2400
END-OF-LIFE NOTICE, NO. 2566 END-OF-SALE AND END-OF-LIFE ANNOUNCEMENT FOR THE CISCO MEDIA CONVERGENCE SERVER 7845H-2400 Cisco Systems announces the end of life of the Cisco Media Convergence Server 7845H-2400.
More informationCisco Extensible Provisioning and Operations Manager 4.5
Data Sheet Cisco Extensible Provisioning and Operations Manager 4.5 Cisco Extensible Provisioning and Operations Manager (EPOM) is a Web-based application for real-time provisioning of the Cisco BTS 10200
More informationMicrosoft Live Communication Server 2005 Enterprise Edition with SP1 to Cisco Unified Presence 6.0(1) and Cisco Unified Communications Manager 5.
Application Note Microsoft Live Communication Server 2005 Enterprise Edition with SP1 to Cisco Unified Presence 6.0(1) and Cisco Unified Communications Manager 5.1(1) July 27, 2007 Initial Version Table
More informationMicrosoft Live Communication Server 2005 Enterprise Edition with SP1 to Cisco Unified Presence 1.0(3) and Cisco Unified CallManager 5.
Application Note Microsoft Live Communication Server 2005 Enterprise Edition with SP1 to Cisco Unified Presence 1.0(3) and Cisco Unified CallManager 5.0(4) February 8, 2007 Revision 2 Table of Contents
More informationCISCO 10GBASE XENPAK MODULES
DATA SHEET CISCO 10GBASE XENPAK MODULES Figure 1 Cisco 10GBASE XENPAK Modules OVERVIEW The range of Cisco 10GBASE XENPAK modules offers customers a wide variety of 10 Gigabit Ethernet connectivity options
More informationCisco Router and Security Device Manager Cisco Easy VPN Server
Application Note Cisco Router and Security Device Manager Cisco Easy VPN Server Introduction This document explains how to configure a Cisco Easy VPN server. Cisco Easy VPN Introduction Cisco Easy VPN
More informationHigh-Availability Solutions for SIP Enabled Voice-over-IP Networks
White Paper High-Availability Solutions for S Enabled Voice-over- Networks The rapid evolution of voice and data technology is significantly changing the business environment. The introduction of services
More informationENHANCED INTERIOR GATEWAY ROUTING PROTOCOL STUB ROUTER FUNCTIONALITY
APPLICATION NOTE ENHANCED INTERIOR GATEWAY ROUTING PROTOCOL STUB ROUTER FUNCTIONALITY OVERVIEW Enhanced Interior Gateway Routing Protocol (EIGRP).Stub Router functionality, which Cisco introduced in Cisco
More informationNEW CISCO IOS SOFTWARE RELEASE 12.2(25)EY FOR CISCO CATALYST 3750 METRO SERIES SWITCHES
PRODUCT BULLETIN NO. 2784 NEW CISCO IOS SOFTWARE RELEASE 12.2(25)EY FOR CISCO CATALYST 3750 METRO SERIES SWITCHES INTRODUCTION Cisco Systems is pleased to announce Cisco IOS Software updates for the Cisco
More informationCisco MCS 7815-I2-UC1 Media Convergence Server
Data Sheet Cisco MCS 7815-I2-UC1 Media Convergence Server PRODUCT OVERVIEW The Cisco MCS 7815-I2-UC1 Media Convergence Server is an entry-level server platform for Cisco Unity Connection and is an integral
More informationCisco Unified IP Phone 7971G-GE
Data Sheet Cisco Unified IP Phone 7971G-GE Cisco Unified IP phones continue to lead the competition with integrated business functions and converged communications features beyond today's conventional
More informationTraffic Offload. Cisco 7200/Cisco 7500 APPLICATION NOTE
APPLICATION NOTE Cisco 700/Cisco 700 Traffic offload allows exchange carriers to offload their telephony traffic to a packet network from the Public Switched Telephone Network (PSTN). By doing so, carriers
More informationCISCO CATALYST 6500 SERIES WITH CISCO IOS SOFTWARE MODULARITY
PRODUCT BULLETIN NO. 3044 CISCO CATALYST 6500 SERIES WITH CISCO IOS SOFTWARE MODULARITY This product bulletin highlights the enhancements available with Cisco IOS Software Modularity on the Cisco Catalyst
More informationCISCO GIGABIT INTERFACE CONVERTER
DATA SHEET CISCO GIGABIT INTERFACE CONVERTER The industry-standard Cisco Gigabit Interface Converter (GBIC) is a hot-swappable input/output device that plugs into a Gigabit Ethernet port or slot, linking
More informationCisco 2651XM Gateway - PBX Interoperability: Ericsson MD-110 PBX using Q.931 BRI User Side Interfaces to an H.323 Gateway
Application Note Cisco 2651XM Gateway - PBX Interoperability: Ericsson MD-110 PBX using Q.931 BRI User Side Interfaces to an H.323 Gateway Introduction This note describes the interoperability between
More informationMicrosoft Office Communications Server 2007 Enterprise Edition to Cisco Unified Presence 6.0(1) and Cisco Unified Communication Manager 6.
Application Note Microsoft Office Communications Server 2007 Enterprise Edition to Cisco Unified Presence 6.0(1) and Cisco Unified Communication Manager 6.0(1) 6/2/2008 Table of Contents Introduction...1
More informationQuick Start Guide Cisco CTE 1400 and Design Studio
Quick Start Guide Cisco CTE 1400 and Design Studio 1 Install the Cisco CTE 1400 2 Configure the Cisco CTE 1400 3 Install Design Studio 4 Start Design Studio 1 Install the Cisco CTE 1400 The Cisco Content
More informationAT&T IP Toll-Free: Connecting Cisco Unified Communications Manager 6.1(1a) via the Cisco Unified Border Element using SIP
Application Note AT&T IP Toll-Free: Connecting Cisco Unified Communications Manager 6.1(1a) via the Cisco Unified Border Element using SIP July 18, 2008 Table of Contents Introduction...2 Network Topology...3
More informationMULTI-VRF AND IP MULTICAST
WHITE PAPER MULTI-VRF AND IP MULTICAST OVERVIEW Multi-VRF Customer Edge (VRF-Lite) enables Multiple VPN routing instances on Customer Edge devices and supports Cisco IOS IP Multicast. Since Multicast has
More informationCisco Voice Services Provisioning Tool 2.6(1)
Data Sheet Cisco Voice Services Provisioning Tool 2.6(1) The Cisco Voice Services Provisioning Tool (VSPT) provides a GUI for the creation, modification, and execution of signaling connections, trunks,
More informationA New Services Aggregation Benchmark for the WAN and MAN The Cisco 7200VXR Series Router
Solutions Overview A New Services Aggregation Benchmark for the WAN and MAN The Cisco 7200VXR Series Router YOUR CHALLENGE Enterprise networks face challenges when aggregating branch offices or remote
More informationBell Canada SIP Trunking Service: Connecting Cisco Unified Communications Manager v6 via the Cisco Unified Border Element using SIP
Application Note Bell Canada SIP Trunking Service: Connecting Cisco Unified Communications Manager v6 via the Cisco Unified Border Element using SIP April 7, 2010 Table of Contents Introduction...2 Network
More informationCISCO AIRONET 1230AG SERIES ACCESS POINT
ORDERING GUIDE CISCO AIRONET 1230AG SERIES ACCESS POINT The Cisco Aironet 1230AG Series Access Point provides the physical interface connections shown in Table 1. Table 1. Cisco Aironet 1230AG Series Connections
More informationCisco Persistent Storage Device
Взято с сайта www.wit.ru Data Sheet Cisco Persistent Storage Device Mobile network operators are now looking to data for revenue. The ability to track the use and type of data services is essential to
More informationAvaya S8500 Version 4.0 to Cisco IOS Voice Gateway using SIP with T1-PRI to PSTN
Application Note Avaya S8500 Version 4.0 to Cisco IOS Voice Gateway using SIP with T1-PRI to PSTN February 20, 2008 Table of Contents Introduction...2 Network Topology...3 Limitations...3 System Components...4
More informationCISCO IPCC EXPRESS EDITION FEATURES AND PRODUCT SPECIFICATIONS
TECHNICAL REFERENCE CISCO IPCC EXPRESS EDITION FEATURES AND PRODUCT SPECIFICATIONS Table 1. IPCC Express 4.0 Feature Premium Enhanced Standard General System Features with Server Software Hardware Configuration
More informationCISCO 7304 SERIES ROUTER PORT ADAPTER CARRIER CARD
DATA SHEET CISCO 7304 SERIES ROUTER PORT ADAPTER CARRIER CARD The Cisco 7304 Router, part of the industry-leading Cisco 7000 Series, is optimized to deliver flexible, high-performance IP and Multiprotocol
More informationAvaya S8500 Communications Manager 2.1 to Cisco IOS Voice Gateway using E1 QSIG with H.323
Application Note Avaya S8500 Communications Manager 2.1 to Cisco IOS Voice Gateway using E1 QSIG with H.323 October 30, 2007 Revision 3 Table of Contents Introduction...1 Network Topology...2 System Components...2
More informationAvaya S8500 Communications Manager 2.1 to Cisco IOS Voice Gateway using T1 QSIG with H.323
Application Note Avaya S8500 Communications Manager 2.1 to Cisco IOS Voice Gateway using T1 QSIG with H.323 October 30, 2007 Revision 6 Table of Contents Introduction...1 Network Topology...2 Limitations...2
More informationCisco 7200VXR Series NPE-G2 Network Processing Engine
Product Bulletin No. 3226 Cisco 7200VXR Series NPE-G2 Network Processing Engine Increasingly, business applications and services affect aggregation requirements and router-integrated services across the
More informationEnd-of-Sale and End-of-Life Announcement for Select Cisco Catalyst 2950G and Catalyst 2950T Series Switches
Product Bulletin No. EOL1094 End-of-Sale and End-of-Life Announcement for Select Cisco Catalyst 2950G and Catalyst 2950T Series Switches Cisco Systems announces the end-of-sale and end-of-life dates for
More informationIP Communications for Small Offices Using Cisco CallManager Express and Cisco Unity Express
Overview IP Communications for Small Offices Using Cisco CallManager Express and Cisco Unity Express Cisco CallManager Express with Cisco Unity Express provides small and medium-sized businesses (SMBs)
More informationCISCO UNIFIED IP PHONE 7912G
DATA SHEET CISCO UNIFIED IP PHONE 7912G Cisco Unified IP phones---an integral component of the Cisco Unified IP Communications system---provide superior levels of integrated business features and converged
More informationCisco Catalyst 2950 Series Software Feature Comparison Standard Image (SI) and Enhanced Image (EI) Feature Comparison
Product Bulletin No. 1855 Cisco Catalyst 2950 Series Software Comparison and Comparison The Cisco Catalyst 2950 Series switches include two software image versions that support different degrees of functionality
More informationC ISCO INTELLIGENCE ENGINE 2100 SERIES M OUNTING AND CABLING
DRIVE 0 DRIVE 1 Quick Start Guide C ISCO INTELLIGENCE ENGINE 2100 SERIES M OUNTING AND CABLING Cisco Intelligence Engine 2100 Series Console Hub 53002 1 TAKE OUT WHAT YOU NEED 2 RACK MOUNT THE HARDWARE
More informationCisco ONS SDH 12-Port STM-1 Electrical Interface Card
Data Sheet Cisco ONS 15454 SDH 12-Port STM-1 Electrical Interface Card The Cisco ONS 15454 SDH 12-Port STM-1 Electrical Interface Card (STM-1E) provides a cost-effective, high-speed electrical interface
More informationCisco CallManager Release 4.1-PBX Interoperability: Avaya Definity G3 MV1.3 PBX using a Cisco 2621XM Gateway with E1 Q.SIG as a MGCP Gateway
CISCOSYSTEMS CISCOSYSTEMS Application Note Cisco CallManager Release 4.1-PBX Interoperability: Avaya Definity G3 MV1.3 PBX using a Cisco 2621XM Gateway with E1 Q.SIG as a MGCP Gateway Introduction This
More informationPPPoE Session Recovery After Reload
If the PPP keepalive mechanism is disabled on a customer premises equipment (CPE) device, a PPP over Ethernet (PPPoE) session will hang indefinitely after an aggregation device reload. The PPPoE Session
More informationThe Cisco Unified Communications Planning and Design Service Bundle
Services Data Sheet Cisco Unified Communications Planning and Design Service Bundle The Cisco Unified Communications Planning and Design Service Bundle, designed for large enterprise networks, helps you
More informationEricsson MD110 BC12 to a Cisco IAD243X using E1-ISDN NET5 with SIP
Application Note Ericsson MD110 BC12 to a Cisco IAD243X using E1-ISDN NET5 with SIP January 11, 2007 Initial Version Table of Contents Introduction...1 Network Topology...2 Limitations...2 Hardware Requirements...3
More informationTHE POWER OF A STRONG PARTNERSHIP.
THE POWER OF A STRONG PARTNERSHIP. Now you can harness a network of resources. Connections, knowledge, and expertise. All focused on your success. The Cisco Channel Partner Program. BE CONNECTED. Great
More informationNEW JERSEY S HIGHER EDUCATION NETWORK (NJEDGE.NET), AN IP-VPN CASE STUDY
CUSTOMER CASE STUDY NEW JERSEY S HIGHER EDUCATION NETWORK (NJEDGE.NET), AN IP-VPN CASE STUDY SUMMARY NJEDge.Net is a nonprofit consortium of 45 colleges and universities in New Jersey dedicated to promoting
More informationAnnouncing the Cisco Wireless IP Phone 7920
Product Bulletin No. 2134 Announcing the Cisco Wireless IP Phone 7920 PRODUCT OVERVIEW Cisco Wireless IP Phone 7920 provides the first generation of wireless IP phones for the Cisco IP Communications Solution.
More informationCisco IOS SIP SRST Version 3.4 Command Reference
Cisco IOS SIP SRST Version 3.4 Command Reference Cisco IOS Release 12.4(4)T October 2005 Corporate Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA http://www.cisco.com
More informationCisco Report Server Readme
Cisco Report Server Readme For Cisco Network Planning Solution 2.1, Cisco Network Planning Solution Service Provider 2.1, and Cisco Application Analysis Solution 2.1 Release 2.1 Americas Headquarters Cisco
More informationTHE CISCO SUCCESS BUILDER PROGRAM THE CISCO SMALL OFFICE COMMUNICATIONS CENTER: AFFORDABLE, PROVEN COMMUNICATIONS SOLUTIONS FOR SMALL ORGANIZATIONS
THE CISCO SUCCESS BUILDER PROGRAM THE CISCO SMALL OFFICE COMMUNICATIONS CENTER: AFFORDABLE, PROVEN COMMUNICATIONS SOLUTIONS FOR SMALL ORGANIZATIONS CISCO SUCCESS BUILDER. IT S MORE THAN AN INCENTIVE PROGRAM.
More informationE-Seminar. Voice over IP. Internet Technical Solution Seminar
E-Seminar Voice over IP Internet Technical Solution Seminar Voice over IP Internet Technical Solution Seminar 3 Welcome 4 Objectives 5 Telephony in Business 6 VoIP and IP Telephony 7 Traditional Telephony
More informationCisco Unified MeetingPlace for Microsoft Office Communicator
QUICK START GUIDE Cisco Unified MeetingPlace for Microsoft Office Communicator Release 6.x Published May 31, 2007 1 Configuring Your Office Communicator Client for Cisco Unified MeetingPlace Conferencing
More informationBGP Enforce the First Autonomous System Path
BGP Enforce the First Autonomous System Path The BGP Enforce the First Autonomous System Path feature is used to configure a Border Gateway Protocol (BGP) routing process to discard updates received from
More informationCisco Smart Business Communications System Teleworker Set Up
Cisco Smart Business Communications System Teleworker Set Up The Cisco Smart Business Communications System is a unified communications solution for small businesses that provides voice, data, video, security,
More informationSuppress BGP Advertisement for Inactive Routes
Suppress BGP Advertisement for Inactive Routes The Suppress BGP Advertisements for Inactive Routes features allows you to configure the suppression of advertisements for routes that are not installed in
More information