CCNA 4 PRAKTISK PRØVE NOTER
|
|
|
- Bryan Short
- 6 years ago
- Views:
Transcription
1 CCNA 4 PRAKTISK PRØVE NOTER Af Adam Andersen TEC CISCO
2 Indhold PPP with Authentication... 2 Configure PPP PAP / CHAP Authentication... 2 Multi link... 2 Debug serial / PPP... 2 Configure Static/Dynamic NAT... 3 Debug NAT show running-config... 3 Configuring GRE... 3 Configuring GRE IPSec... 4 Debug... 4 Configure Frame-Relay... 5 NTP / Timestamp / debugging / SNMP... 5 NTP client... 5 Debugging level... 5 SNMP accesslist... 5 Debug NTP / Time / logging / SNMP / NetFlow S ide
3 PPP with Authentication R3(config)# interface serial 0/0/0 R3(config-if)# encapsulation ppp R3(config-if)# compress [ predictor stac ] Configure PPP PAP / CHAP Authentication R1(config)# username R3 secret class R1(config)# interface s0/0/0 R1(config-if)# ppp authentication pap R1(config-if)# ppp pap sent-username R1 password cisco CHAP Router(config)# hostname ISP ISP(config)# username R3 secret cisco ISP(config)# interface s0/0/0 ISP(config-if)# ppp authentication chap R3(config)# username ISP secret cisco R3(config)# interface serial0/1/0 R3(config-if)# ppp authentication chap Multi link interface multilink Debug serial / PPP show interfaces serial show controllers show controllers cbus show controllers serial debug ppp authentication 2 S ide
4 Configure Static/Dynamic NAT Static R1(config)#ip nat inside source static Interface private IP R1(config)#ip nat inside Interface public IP R1(config)#ip nat outside Dynamic R2(config)#ip nat pool dynamic netmask R2(config)#access-list 1 permit R2(config)#ip nat inside source list 1 pool dynamic Interface private IP inside NAT R1(config)#ip nat inside Interface public IP outside NAT R1(config)#ip nat outside PAT R2(config)#ip nat pool R2POOL netmask R2(config)#ip access-list standard R2NAT R2(config)#ip nat inside source list R2NAT pool R2POOL overload Debug NAT show running-config show ip nat translations show ip nat statistics show ip nat translation timeout clear ip nat translation Configuring GRE RA(config)#interface tunnel 0 RA(config-if)#ip address RA(config-if)#tunnel source serial 0/0/0 RA(config-if)#tunnel destination RA(config-if)#tunnel mode gre ip Static tunnel route to private IP RA(config)# ip route RB(config)# ip route S ide
5 Configuring GRE IPSec R1(config)# license boot module c2900 technology-package securityk9 Configure ACL 101 to identify the traffic from the LAN on R1 to the LAN on R2 and R3 as interesting. This interesting traffic will trigger the IPsec VPN to be implemented whenever there is traffic between the R1 and R2 - R3 LANs. All other traffic sourced from the LANs will not be encrypted. Remember that because of the implicit deny any, there is no need to add the statement to the list. R1(config)# access-list 101 permit ip Configure the ISAKMP Phase 1 Configure the crypto ISAKMP policy 101 properties on R1 along with the shared crypto key cisco. Default values do not have to be configured therefore only the encryption, key exchange method, and DH method must be configured. R1(config)# crypto isakmp policy 101 R1(config-isakmp)# encryption aes R1(config-isakmp)# authentication pre-share R1(config-isakmp)# group 5 R1(config-isakmp)# exit Generate isakmp keys for each peer of R1(config)# crypto isakmp key cisco address R1(config)# crypto isakmp key cisco address Configure the ISAKMP Phase 2 properties Create the transform-set VPN-SET to use esp-aes and esp-sha-hmac. Then create the crypto map VPN-MAP that binds all of the Phase 2 parameters together. Use sequence number 101 and identify it as an ipsec-isakmp map. R1(config)# crypto ipsec transform-set R1_Set esp-aes esp-sha-hmac R1(config)# crypto map R1_Map 101 ipsec-isakmp R1(config-crypto-map)# set peer R1(config-crypto-map)# set peer R1(config-crypto-map)# set transform-set R1_Set R1(config-crypto-map)# match address 101 R1(config-crypto-map)# exit Configure the crypto map on the outgoing interface. Finally, bind the R1_Map crypto map to the outgoing Serial 0/0/0 interface. Note: This is not graded. R1(config)# interface S0/0/0 R1(config-if)# crypto map R1_Map Debug Show version 4 S ide
6 Configure Frame-Relay Encapsulation R1(config)# interface s0/0/0 R1(config-if)# encapsulation frame-relay MAP IP WITH DLCI R1(config)# interface s0/0/0 R1(config-if)# frame-relay map ip broadcast R1(config-if)# frame-relay map ip broadcast Set LMI type R1(config-if)# frame-relay lmi-type ansi NTP / Timestamp / debugging / SNMP Clock set NTP server Ntp master 1 NTP client Ntp server [ntp master ip] ntp update-calendar timestamp R1(config)#service timestamps log datetime msec Debugging level R1(config)#logging trap debugging Syslog R1(config)# logging SNMP accesslist R1(config)#ip access-list standard SNMP-ACCES SNMP R1(config-std-nacl)#snmp-server community SA-LAB ro SNMP-ACCESS R1(config)#snmp-server host version 2c SA-LAB R1(config)#snmp-server enable traps R2(config-if)#ip flow ingress R2(config-if)#ip flow egress R2(config)#ip flow-export destination R2(config)#ip flow-export version 9 5 S ide
7 Debug NTP / Time / logging / SNMP / NetFlow Show clock Show ntp associations Show logging Show snmp show snmp community Show ip cache flow show ip flow interface 6 S ide
Packet Tracer - Configure and Verify a Site-to-Site IPsec VPN Using CLI
Packet Tracer - Configure and Verify a Site-to-Site IPsec VPN Using CLI Topology Addressing Table R1 R2 R3 Device Interface IP Address Subnet Mask Default Gateway Switch Port G0/0 192.168.1.1 255.255.255.0
Skills Assessment Student Training Exam
Skills Assessment Student Training Exam Topology Assessment Objectives Part 1: Initialize Devices (2 points, 5 minutes) Part 2: Configure Device Basic Settings (18 points, 20 minutes) Part 3: Configure
L2TP IPsec Support for NAT and PAT Windows Clients
L2TP IPsec Support for NAT and PAT Windows Clients The L2TP IPsec Support for NAT and PAT Windows Clients feature allows mulitple Windows client to connect to an IPsec-enabled Cisco IOS Layer 2 Tunneling
CCNA Security 1.0 Student Packet Tracer Manual
1.0 Student Packet Tracer Manual This document is exclusive property of Cisco Systems, Inc. Permission is granted to print and copy this document for non-commercial distribution and exclusive use by instructors
Pre-Fragmentation for IPSec VPNs
Pre-Fragmentation for IPSec VPNs Feature History Release 12.1(11b)E 12.2(13)T 12.2(14)S Modification This feature was introduced. This feature was integrated into Cisco IOS Release 12.2(13)T. This feature
Configuring Dynamic Multipoint VPN Using GRE Over IPsec With OSPF, NAT, and Cisco IOS Firewall
Configuring Dynamic Multipoint VPN Using GRE Over IPsec With OSPF, NAT, and Cisco IOS Firewall Document ID: 43068 Contents Introduction Prerequisites Requirements Components Used Conventions Configure
Configuration Summary
POWER ACT NETWORK PIX Firewall SERIES How to configure dynamic IPSec tunneling Configuration Summary This document describes configuring an NSE initiated IPSec tunnel from behind a NAT device to a VPN
IOS Router : Easy VPN (EzVPN) in Network Extension Mode (NEM) with Split tunnelling Configuration Example
IOS Router : Easy VPN (EzVPN) in Network Extension Mode (NEM) with Split tunnelling Configuration Example Document ID: 63098 Contents Introduction Prerequisites Requirements Components Used Conventions
Configuring a VPN Using Easy VPN and an IPSec Tunnel, page 1
Configuring a VPN Using Easy VPN and an IPSec Tunnel This chapter provides an overview of the creation of Virtual Private Networks (VPNs) that can be configured on the Cisco 819, Cisco 860, and Cisco 880
Internet. SonicWALL IP Cisco IOS IP IP Network Mask
Prepared by SonicWALL, Inc. 9/20/2001 Introduction: VPN standards are still evolving and interoperability between products is a continued effort. SonicWALL has made progress in this area and is interoperable
LAN to LAN IPsec Tunnel Between a Cisco VPN 3000 Concentrator and Router with AES Configuration Example
LAN to LAN IPsec Tunnel Between a Cisco VPN 3000 Concentrator and Router with AES Configuration Example Document ID: 26402 Contents Introduction Prerequisites Requirements Components Used Conventions Configure
1.1 Configuring HQ Router as Remote Access Group VPN Server
Notes: 1.1 Configuring HQ Router as Remote Access Group VPN Server Step 1 Enable AAA model for local and remote access authentication. AAA will prompt extended authentication for remote access group VPN
Deploying the Barracuda Link Balancer with Cisco ASA VPN Tunnels
Deploying the Barracuda Link Balancer with Cisco ASA VPN Tunnels This article provides a reference for deploying a Barracuda Link Balancer under the following conditions: 1. 2. In transparent (firewall-disabled)
CCNA Security PT Practice SBA
A few things to keep in mind while completing this activity: 1. Do not use the browser Back button or close or reload any Exam windows during the exam. 2. Do not close Packet Tracer when you are done.
Chapter 7. IP Addressing Services. IP Addressing Services. Part I
Chapter 7 IP Addressing Services Part I CCNA4-1 Chapter 7-1 IP Addressing Services Dynamic Host Configuration Protocol (DHCP) CCNA4-2 Chapter 7-1 Dynamic Host Configuration Protocol (DHCP) Every device
CCNP TSHOOT. Quick Reference Sheet Exam
CCNP TSHOOT Quick Reference Sheet Exam 300-135 Chapter 1. Network Principles Troubleshooting Steps Problem Identification Collection of Information Examination and Action Plan Verification Basic Troubleshooting
IPsec Anti-Replay Window Expanding and Disabling
IPsec Anti-Replay Window Expanding and Disabling Cisco IP security (IPsec) authentication provides anti-replay protection against an attacker duplicating encrypted packets by assigning a unique sequence
Configuration Professional: Site to Site IPsec VPN Between Two IOS Routers Configuration Example
Configuration Professional: Site to Site IPsec VPN Between Two IOS Routers Configuration Example Document ID: 113337 Contents Introduction Prerequisites Requirements Components Used Conventions Configuration
Network Security 2. Module 4 Configure Site-to-Site VPN Using Pre-Shared Keys
1 1 Network Security 2 Module 4 Configure Site-to-Site VPN Using Pre-Shared Keys 2 Learning Objectives 4.1 Prepare a Router for Site-to-Site VPN using Pre-shared Keys 4.2 Configure a Router for IKE Using
Chapter 6: Infrastructure Services
Chapter 6: Infrastructure Services Network Time Protocol There are many things involved in the securing of a network such as security logs along with an accurate date and timestamp. Secondly, when an attack
Configuring LAN-to-LAN IPsec VPNs
CHAPTER 28 A LAN-to-LAN VPN connects networks in different geographic locations. The ASA 1000V supports LAN-to-LAN VPN connections to Cisco or third-party peers when the two peers have IPv4 inside and
co Configuring PIX to Router Dynamic to Static IPSec with
co Configuring PIX to Router Dynamic to Static IPSec with Table of Contents Configuring PIX to Router Dynamic to Static IPSec with NAT...1 Introduction...1 Configure...1 Components Used...1 Network Diagram...1
MWA Deployment Guide. VPN Termination from Smartphone to Cisco ISR G2 Router
MWA Deployment Guide Mobile Workforce Architecture: VPN Deployment Guide for Microsoft Windows Mobile and Android Devices with Cisco Integrated Services Router Generation 2 This deployment guide explains
This document is intended to give guidance on how to read log entries from a Cisco PIX / ASA. The specific model in this case was a PIX 501.
1.0 Overview This document is intended to give guidance on how to read log entries from a Cisco PIX / ASA. The specific model in this case was a PIX 501. 2.0 PIX Config The following is the PIX config
Configuring IOS to IOS IPSec Using AES Encryption
Configuring IOS to IOS IPSec Using AES Encryption Document ID: 43069 Contents Introduction Prerequisites Requirements Components Used Conventions Configure Configurations Verify Troubleshoot Troubleshooting
Lab - Configuring a Site-to-Site VPN Using Cisco IOS and CCP
CCNA Security Lab - Configuring a Site-to-Site VPN Using Cisco IOS and CCP Topology Note: ISR G2 devices use GigabitEthernet interfaces instead of FastEthernet Interfaces. 2015 Cisco and/or its affiliates.
Cisco IOS Firewall Authentication Proxy
Cisco IOS Firewall Authentication Proxy This feature module describes the Cisco IOS Firewall Authentication Proxy feature. It includes information on the benefits of the feature, supported platforms, configuration
Lab 8.5.2: Troubleshooting Enterprise Networks 2
Lab 8.5.2: Troubleshooting Enterprise Networks 2 Topology Diagram Addressing Table Device Interface IP Address Subnet Mask Default Gateway Fa0/0 192.168.10.1 255.255.255.0 N/A R1 Fa0/1 192.168.11.1 255.255.255.0
Network Security CSN11111
Network Security CSN11111 VPN part 2 12/11/2010 r.ludwiniak@napier.ac.uk Five Steps of IPSec Step 1 - Interesting Traffic Host A Router A Router B Host B 10.0.1.3 10.0.2.3 Apply IPSec Discard Bypass IPSec
Router Allows VPN Clients to Connect IPsec and Internet Using Split Tunneling Configuration Example
Router Allows VPN Clients to Connect IPsec and Internet Using Split Tunneling Configuration Example Document ID: 91193 Contents Introduction Prerequisites Requirements Components Used Conventions Background
Chapter 8 Lab Configuring a Site-to-Site VPN Using Cisco IOS
Chapter 8 Lab Configuring a Site-to-Site VPN Using Cisco IOS Topology Note: ISR G1 devices use FastEthernet interfaces instead of GigabitEthernet interfaces. 2017 Cisco and/or its affiliates. All rights
Lab Configuring and Verifying Standard IPv4 ACLs (Instructor Version Optional Lab)
(Instructor Version Optional Lab) Instructor Note: Red font color or gray highlights indicate text that appears in the instructor copy only. Optional activities are designed to enhance understanding and/or
Cisco DSL Router Configuration and Troubleshooting Guide Cisco DSL Router Acting as a PPPoE Client with a Dynamic IP Address
Cisco DSL Router Configuration and Troubleshooting Guide Cisco DSL Router Acting as a PPPoE Client with a Dynamic IP Address Document ID: 71118 Contents Introduction Prerequisites Requirements Components
Lab Configuring Port Address Translation (PAT) (Instructor Version)
(Instructor Version) Instructor Note: Red font color or gray highlights indicate text that appears in the instructor copy only. Topology Addressing Table Objectives Device Interface IP Address Subnet Mask
Feature-by-Feature Router Configurations
CHAPTER 3 Feature-by-Feature Router Configurations This chapter includes feature-by-feature configuration procedures for the Cisco 806 router. This chapter is useful if you have a network in place and
Static VTI R1: (previous tunnel 0 config remains the same)
VTI is used when you need to apply different policies to the actual external interface and the tunnel, so you create virtual tunnel interface for that VPN traffic. Static VTI R1: (previous tunnel 0 config
IPv6 over IPv4 GRE Tunnel Protection
The feature allows both IPv6 unicast and multicast traffic to pass through a protected generic routing encapsulation (GRE) tunnel. Finding Feature Information, page 1 Prerequisites for, page 1 Restrictions
Sample Business Ready Branch Configuration Listings
APPENDIX A Sample Business Ready Branch Configuration Listings The following is a sample configuration of a Business Ready Branch. There are many permutations of feature combinations when setting up the
Configuring PPP over Ethernet with NAT
CHAPTER 3 The Cisco Secure Router 520 Ethernet-to-Ethernet routers support Point-to-Point Protocol over Ethernet (PPPoE) clients and network address translation (NAT). Multiple PCs can be connected to
VPN Connection through Zone based Firewall Router Configuration Example
VPN Connection through Zone based Firewall Router Configuration Example Document ID: 112051 Contents Introduction Prerequisites Requirements Components Used Conventions Background Information Configure
Table of Contents. Cisco IPSec Tunnel through a PIX Firewall (Version 7.0) with NAT Configuration Example
Table of Contents IPSec Tunnel through a PIX Firewall (Version 7.0) with NAT Configuration Example...1 Document ID: 63881...1 Introduction...1 Prerequisites...2 Requirements...2 Components Used...2 Conventions...2
Securizarea Calculatoarelor și a Rețelelor 28. Implementarea VPN-urilor IPSec Site-to-Site
Platformă de e-learning și curriculă e-content pentru învățământul superior tehnic Securizarea Calculatoarelor și a Rețelelor 28. Implementarea VPN-urilor IPSec Site-to-Site Site-to-Site IPsec VPNs Behaviour
Skills Assessment. CCNA Routing and Switching: Connecting Networks. Topology. Assessment Objectives. Scenario
Skills Assessment Topology Assessment Objectives Part 1: Configure Device Basic Settings (15 points, 15 minutes) Part 2: Configure PPP Connections (20 points, 10 minutes) Part 3: Configure IPv4 ACL for
Securizarea Calculatoarelor și a Rețelelor 29. Monitorizarea și depanarea VPN-urilor IPSec Site-to-Site
Platformă de e-learning și curriculă e-content pentru învățământul superior tehnic Securizarea Calculatoarelor și a Rețelelor 29. Monitorizarea și depanarea VPN-urilor IPSec Site-to-Site Site-to-Site IPsec
The MSCHAP Version 2 feature (introduced in Cisco IOS Release 12.2(2)XB5) allows Cisco routers to
The feature (introduced in Cisco IOS Release 12.2(2)XB5) allows Cisco routers to utilize Microsoft Challenge Handshake Authentication Protocol Version 2 (MSCHAP V2) authentication for PPP connections between
Note that you can also use the password command but the secret command gives you a better encryption algorithm.
Router Device Security Lab Configuring Secure Passwords 1. Configure the enable secret and password enable password TRUSTME enable secret letmein Look at the configuration: show config terminal Note the
Contents. Introduction. Prerequisites. Background Information
Contents Introduction Prerequisites Background Information Limitation Configure Network Diagram Initial configuration R2 R3 IPSec configuration R2 EzPM configuration Workaround Verify Troubleshooting Related
IPsec Management Configuration Guide Cisco IOS Release 12.4T
IPsec Management Configuration Guide Cisco IOS Release 12.4T Americas Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA http://www.cisco.com Tel: 408 526-4000 800 553-NETS
Lab Configuring Dynamic and Static NAT (Solution)
(Solution) Topology Addressing Table Objectives Device Interface IP Address Subnet Mask Default Gateway Gateway G0/1 192.168.1.1 255.255.255.0 N/A S0/0/1 209.165.201.18 255.255.255.252 N/A ISP S0/0/0 (DCE)
LAN-to-LAN IPsec VPNs
A LAN-to-LAN VPN connects networks in different geographic locations. You can create LAN-to-LAN IPsec connections with Cisco peers and with third-party peers that comply with all relevant standards. These
Configure ISDN Connectivity between Remote Sites
Case Study 1 Configure ISDN Connectivity between Remote Sites Cisco Networking Academy Program CCNP 2: Remote Access v3.1 Objectives In this case study, the following concepts are covered: Asynchronous
Cisco Virtual Office: Easy VPN Deployment Guide
Cisco Virtual Office: Easy VPN Deployment Guide This guide provides detailed design and implementation information for deployment of Easy VPN in client mode with the Cisco Virtual Office. Please refer
PPP over Frame Relay
The feature allows a router to establish end-to-end Point-to-Point Protocol (PPP) sessions over Frame Relay. Finding Feature Information, page 1 Prerequisites for, page 1 Restrictions for, page 2 Information
Lab Configuring Dynamic and Static NAT (Instructor Version Optional Lab)
(Instructor Version Optional Lab) Instructor Note: Red font color or gray highlights indicate text that appears in the instructor copy only. Optional activities are designed to enhance understanding and/or
15. PPP and Frame relay in small network
Published on cdesigner.eu (https://cdesigner.eu) Home > Networks > 15. PPP and Frame relay in small network 15. PPP and Frame relay in small network PPP and Frame relay are protocols operating at data
Split DNS. Finding Feature Information
The feature enables a Cisco device to respond to Domain Name System (DNS) queries using a specific configuration and associated host table cache that are selected based on certain characteristics of the
IPsec Anti-Replay Window: Expanding and Disabling
IPsec Anti-Replay Window: Expanding and Disabling First Published: February 28, 2005 Last Updated: March 24, 2011 Cisco IP security (IPsec) authentication provides anti-replay protection against an attacker
Virtual Tunnel Interface
This chapter describes how to configure a VTI tunnel. About s, on page 1 Guidelines for s, on page 1 Create a VTI Tunnel, on page 2 About s The ASA supports a logical interface called (VTI). As an alternative
Loading Internet Protocol Security (IPSec) (CDR-882/780/790/990 Cellular Router)
Loading Internet Protocol Security (IPSec) (CDR-882/780/790/990 Cellular Router) Call Direct Document version 1.4 Last updated 17 December, 2010 support@call-direct.com.au Loading IPSec To support IPSec
Lab 9: VPNs IPSec Remote Access VPN
Lab 9: VPNs IPSec Remote Access VPN Rich Macfarlane 2015 Aim: Details The aim of this lab is to introduce Virtual Private Network (VPN) concepts, using an IPSec remote access VPN between a remote users
Security for VPNs with IPsec Configuration Guide Cisco IOS Release 12.4T
Security for VPNs with IPsec Configuration Guide Cisco IOS Release 12.4T Americas Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA http://www.cisco.com Tel: 408 526-4000
Troubleshooting, Editing, Port # s
CCNA Commands Summary Page 1 of 23 Troubleshooting, Editing, Port # s show ip interface brief (display interface designations, IP address and status) show ip route (display routing table) show vlan brief
Configuring the PIX Firewall and VPN Clients Using PPTP, MPPE and IPSec
Configuring the PIX Firewall and VPN Clients Using PPTP, MPPE and IPSec Document ID: 14095 Contents Introduction Prerequisites Requirements Components Used Conventions Configure Network Diagram Configurations
PIX/ASA 7.x and Later : Easy VPN with Split Tunneling ASA 5500 as the Server and Cisco 871 as the Easy VPN Remote Configuration Example
PIX/ASA 7.x and Later : Easy VPN with Split Tunneling ASA 5500 as the Server and Cisco 871 as the Easy VPN Remote Configuration Example Document ID: 68815 Contents Introduction Prerequisites Requirements
Regular Expressions to Remove Passwords From IOS Configurations
Regular Expressions to Remove Passwords From IOS Configurations Regex ReplaceString ^[ ]*username[ ]+(\S*)[ ]+password[ ]+([0-9]+)[ username xxxxxxxx password $2 xxxxxxxx ^[ ]*username[ ]+(\S*)[ ]+password[
This document is a tutorial related to the Router Emulator which is available at:
Introduction This document is a tutorial related to the Router Emulator which is available at: http://www.dcs.napier.ac.uk/~bill/router.html A demo is also available at: http://www.dcs.napier.ac.uk/~bill/router_demo.htm
Configuring Authentication Proxy
The Cisco IOS Firewall Authentication Proxy feature provides dynamic, per-user authentication and authorization, authenticating users against industry standard TACACS+ and RADIUS authentication protocols.
ROUTER COMMANDS. BANNER: Config# banner motd # TYPE MESSAGE HERE # - # can be substituted for any character, must start and finish the message
ROUTER COMMANDS TERMINAL CONTROLS: Config# terminal editing - allows for enhanced editing commands Config# terminal monitor - shows output on telnet session Config# terminal ip netmask-format hexadecimal
SSG Configuration Example
APPENDIX A Example A-1 is a sample SSG configuration for the Cisco 10000 series router based on the topology in Figure A-1. The configuration includes AAA, PPP, SSG, and RADIUS. The SSG configuration enables
Split DNS. Finding Feature Information
The feature enables a Cisco device to respond to Domain Name System (DNS) queries using a specific configuration and associated host table cache that are selected based on certain characteristics of the
CCNP 2: Remote Access
Scope and Sequence CCNP 2: Remote Access Cisco Networking Academy Program Version 3.1 Table of Contents CCNP 2: REMOTE ACCESS...1 TABLE OF CONTENTS...2 TARGET AUDIENCE...3 PREREQUISITES...3 COURSE DESCRIPTION...3
The primary audience for this course includes Network Administrators, Network Engineers,
CCNA COURSE DESCRIPTION: Cisco Certified Network Associate (CCNA) validates the ability to install, configure, operate, and troubleshoot medium-size route and switched networks, including implementation
Google Cloud VPN Interop Guide
Google Cloud VPN Interop Guide Using Cloud VPN With Cisco ASA Courtesy of Cisco Systems, Inc. Unauthorized use not permitted. Cisco is a registered trademark or trademark of Cisco Systems, Inc. and/or
Quick Note. Configure an IPSec VPN tunnel in Aggressive mode between a TransPort LR router and a Cisco router. Digi Technical Support 7 October 2016
Quick Note Configure an IPSec VPN tunnel in Aggressive mode between a TransPort LR router and a Cisco router. Digi Technical Support 7 October 2016 Contents 1 Introduction... 3 1.1 Outline... 3 1.2 Assumptions...
CCNA 4 - Final Exam (A)
CCNA 4 - Final Exam (A) 1. A network administrator is asked to design a system to allow simultaneous access to the Internet for 250 users. The ISP for this network can only supply five public IPs. What
Implementing Cisco IP Routing
300-101 Implementing Cisco IP Routing NWExam.com SUCCESS GUIDE TO CISCO CERTIFICATION Exam Summary Syllabus Questions Table of Contents Introduction to 300-101 Exam on Implementing Cisco IP Routing...
ACADEMIA LOCAL CISCO UCV-MARACAY CONTENIDO DE CURSO CURRICULUM CCNA. SEGURIDAD SEGURIDAD EN REDES. NIVEL II. VERSION 2.0
ACADEMIA LOCAL CISCO UCV-MARACAY CONTENIDO DE CURSO CURRICULUM CCNA. SEGURIDAD SEGURIDAD EN REDES. NIVEL II. VERSION 2.0 Module 1: Intrusion Detection and Prevention Technology 1.1 Overview of Intrusion
Configuring Virtual Asynchronous Traffic over ISDN
Configuring Virtual Asynchronous Traffic over ISDN Cisco IOS software offers two solutions to send virtual asynchronous traffic over ISDN: Using International Telecommunication Union Telecommunication
CCNA 4 - Final Exam Answers
CCNA 4 - Final Exam Answers 1 Which of the following describes the roles of devices in a WAN? (Choose three.) *** A CSU/DSU terminates a digital local loop. A modem terminates a digital local loop. A CSU/DSU
Mediant MSBR. Version 6.8. Security Setup. Configuration Guide. Version 6.8. AudioCodes Family of Multi-Service Business Routers (MSBR)
Configuration Guide AudioCodes Family of Multi-Service Business Routers (MSBR) Mediant MSBR Security Setup Version 6.8 Version 6.8 May 2014 Document # LTRT-31640 Configuration Guide Contents Table of
VPN Between Sonicwall Products and Cisco Security Appliance Configuration Example
VPN Between Sonicwall Products and Cisco Security Appliance Configuration Example Document ID: 66171 Contents Introduction Prerequisites Requirements Components Used Related Products Conventions Configure
NetVanta PowerPak. Virtual Instructor-Led Training Lab Guide
NetVanta PowerPak Virtual Instructor-Led Training Lab Guide Trademarks Any brand names and product names included in this manual are trademarks, registered trademarks, or trade names of their respective
Cradlepoint to Palo Alto VPN Example. Summary. Standard IPSec VPN Topology. Global Leader in 4G LTE Network Solutions
Cradlepoint to Palo Alto VPN Example Summary This configuration covers an IPSec VPN tunnel setup between a Cradlepoint Series 3 router and a Palo Alto firewall. IPSec is customizable on both the Cradlepoint
Table of Contents. Cisco PIX/ASA 7.x Enhanced Spoke to Spoke VPN Configuration Example
Table of Contents PIX/ASA 7.x Enhanced Spoke to Spoke VPN Configuration Example...1 Document ID: 64692...1 Introduction...1 Prerequisites...1 Requirements...1 Components Used...1 Conventions...2 Configure...2
Table of Contents. Cisco Enhanced Spoke to Client VPN Configuration Example for PIX Security Appliance Version 7.0
Table of Contents Enhanced Spoke to Client VPN Configuration Example for PIX Security Appliance Version 7.0...1 Document ID: 64693...1 Introduction...1 Prerequisites...1 Requirements...1 Components Used...1
ASA Version 7.2(4)30! hostname vpn domain-name hollywood.com enable password BO5OGdtIUElAVJc7 encrypted passwd BO5OGdtIUElAVJc7 encrypted names name
ASA Version 7.2(4)30 hostname vpn domain-name hollywood.com enable password BO5OGdtIUElAVJc7 encrypted passwd BO5OGdtIUElAVJc7 encrypted names name 172.30.232.128 XL description XL / idot name 172.28.28.0
Packet Tracer - Configure Cisco Routers for Syslog, NTP, and SSH Operations (Instructor Version)
Packet Tracer - Configure Cisco Routers for Syslog, NTP, and SSH Operations (Instructor Version) Instructor Note: Red font color or Gray highlights indicate text that appears in the instructor copy only.
Teacher s Reference Manual
UNIVERSITY OF MUMBAI Teacher s Reference Manual Subject: Security in Computing Practical with effect from the academic year 2018 2019 Practical 1: Packet Tracer - Configure Cisco Routers for Syslog, NTP,
SYSLOG Enhancements for Cisco IOS EasyVPN Server
SYSLOG Enhancements for Cisco IOS EasyVPN Server In some situations the complexity or cost of the authentication, authorization, and accounting (AAA) server prohibits its use, but one of its key function
Cisco.Actualtests v New Questions.by.Nev.32q.vce
Cisco.Actualtests.200-120.v2014-01-10.New Questions.by.Nev.32q.vce Number: 200-120 Passing Score: 800 Time Limit: 120 min File Version: 1.0 http://www.gratisexam.com/ Exam A QUESTION 1 1 Which three are
Configuring Layer 2 Tunneling Protocol (L2TP) over IPSec
Configuring Layer 2 Tunneling Protocol (L2TP) over IPSec Document ID: 14122 Introduction Prerequisites Requirements Components Used Conventions Configure Network Diagram Configurations Verify Troubleshoot
TestOut Routing and Switching Pro - English 6.0.x COURSE OUTLINE. Modified
TestOut Routing and Switching Pro - English 6.0.x COURSE OUTLINE Modified 2017-07-10 TestOut Routing and Switching Pro Outline- English 6.0.x Videos: 133 (15:42:34) Demonstrations: 78 (7:22:19) Simulations:
Implementing Dynamic Multipoint VPN for IPv6
Implementing Dynamic Multipoint VPN for IPv6 First Published: July 11, 2008 Last Updated: November 24, 2010 This document describes how to implement Dynamic Multipoint VPN for IPv6 feature, which allows
Mediant MSBR. Version 6.8. Security Setup. Configuration Guide. Version 7.2. AudioCodes Family of Multi-Service Business Routers (MSBR)
Configuration Guide AudioCodes Family of Multi-Service Business Routers (MSBR) Mediant MSBR Security Setup Version 7.2 Version 6.8 May 2014 Document # LTRT-31640 Configuration Guide Contents Table of
VPN Overview. VPN Types
VPN Types A virtual private network (VPN) connection establishes a secure tunnel between endpoints over a public network such as the Internet. This chapter applies to Site-to-site VPNs on Firepower Threat
VNS3 IPsec Configuration. VNS3 to Cisco ASA ASDM 5.2
VNS3 IPsec Configuration VNS3 to Cisco ASA ASDM 5.2 Site-to-Site IPsec Tunnel IPsec protocol allows you to securely connect two sites together over the public internet using cryptographically secured services.
Lab Configuring and Verifying Standard IPv4 ACLs Topology
Topology 2016 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 1 of 10 Addressing Table Objectives Device Interface IP Address Subnet Mask Default Gateway R1 G0/1 192.168.10.1
IPsec Dead Peer Detection Periodic Message Option
IPsec Dead Peer Detection Periodic Message The IPsec Dead Peer Detection Periodic Message feature is used to configure the router to query the liveliness of its Internet Key Exchange (IKE) peer at regular
Configuring Authentication Proxy
Configuring Authentication Proxy Last Updated: January 7, 2013 The Cisco IOS Firewall Authentication Proxy feature provides dynamic, per-user authentication and authorization, authenticating users against
IOS/CCP: Dynamic Multipoint VPN using Cisco Configuration Professional Configuration Example
IOS/CCP: Dynamic Multipoint VPN using Cisco Configuration Professional Configuration Example Document ID: 113265 Contents Introduction Prerequisites Requirements Components Used Conventions Background