Configuring a Cisco 827 Router Using PPPoA With CHAP and PAP
|
|
|
- Domenic Hamilton
- 6 years ago
- Views:
Transcription
1 Configuring a Cisco 827 Router Using PPPoA With CHAP and PAP Document ID: Contents Introduction Before You Begin Conventions Prerequisites Components Used Configure Network Diagram PPPoA Using CHAP Configurations PPPoA Using PAP Configuration Verify Troubleshoot Related Information Introduction The sample configurations in this document show a Cisco 827 Digital Subscriber Line (DSL) Router connecting to a Cisco 6130 Digital Subscriber Line Access Multiplexer (DSLAM) and terminating on a Cisco 6400 Universal Access Concentrator (UAC). Each configuration uses Point to Point Protocol over Asynchronous Transfer Mode (PPPoA). The Asynchronous Transfer Mode (ATM) interface is configured for AALMUX PPP encapsulation. One configuration shows PPPoA using Challenge Handshake Authentication Protocol (CHAP). The second configuration shows PPP over ATM using Password Authentication Protocol (PAP). Before You Begin Conventions For more information on document conventions, see the Cisco Technical Tips Conventions. Prerequisites There are no specific prerequisites for this document. Components Used The information in this document is based on the software and hardware versions below. Cisco 827 4V customer premises equipment (CPE) IOS Software Release 12.1(1)XB Cisco 6400 UAC NRP IOS Software Release 12.0(7)DC Cisco 6400 UAC NSP IOS Software Release 12.0(4)DB Cisco 6130 DSLAM NI2 IOS Software Release 12.1(1)DA
2 The information presented in this document was created from devices in a specific lab environment. All of the devices used in this document started with a cleared (default) configuration. If you are working in a live network, ensure that you understand the potential impact of any command before using it. Configure In this section, you are presented with the information to configure the features described in this document. Note: To find additional information on the commands used in this document, use the Command Lookup Tool (registered customers only). Network Diagram This document uses the network setup shown in the diagram below. PPPoA Using CHAP Configurations When using interface virtual template, configure only ppp chap hostname and ppp chap. The ppp authentication chap callin command is not supported. In this example interface dialer is used, which is not affected. Cisco 827 Current configuration: version 12.1 service timestamps debug datetime msec service timestamps log datetime msec hostname R1 ip subnet zero interface Ethernet0 ip address interface ATM0 no ip address no atm ilmi keepalive pvc 1/150 encapsulation aal5mux ppp dialer dialer pool member 1
3 hold queue 224 in interface Dialer0 ip address encapsulation ppp dialer pool 1 dialer group 1 ppp authentication chap callin ppp chap hostname ppp chap ip classless ip route Dialer0 dialer list 1 protocol ip permit end Cisco Access 6400 NRP1 The and values must match the and values of the remote device. interface ATM0/0/0.200 point to point no ip route cache pvc 1/301 encapsulation aal5mux ppp Virtual Template11 interface Virtual Template11 ip address ppp authentication chap ip route PPPoA Using PAP Configuration When using interface virtual template, configure only ppp pap sent. The ppp authentication pap callin command is not supported. In this example interface dialer is used, which is not affected. Cisco 827 version 12.1 service timestamps debug datetime msec service timestamps log datetime msec hostname R1
4 ip subnet zero interface Ethernet0 ip address interface ATM0 no ip address no atm ilmi keepalive pvc 1/150 encapsulation aal5mux ppp dialer dialer pool member 1 hold queue 224 in interface Dialer0 ip address encapsulation ppp dialer pool 1 dialer group 1 ppp authentication pap callin ppp pap sent ip classless ip route Dialer0 no ip http server dialer list 1 protocol ip permit voice port 1 voice port 2 voice port 3 voice port 4 Cisco Access 6400 NRP1 The and values must match the and values of the remote device. interface ATM0/0/0.200 point to point no ip route cache pvc 1/301
5 encapsulation aal5mux ppp Virtual Template11 interface Virtual Template11 ip address ppp authentication pap ip route Verify There is currently no verification procedure available for this configuration. Troubleshoot There is currently no specific troubleshooting information available for this configuration. Related Information DSL Technical Support Technical Support Cisco Systems Contacts & Feedback Help Site Map Cisco Systems, Inc. All rights reserved. Terms & Conditions Privacy Statement Cookie Policy Trademarks of Cisco Systems, Inc. Updated: Nov 23, 2007 Document ID: 12886
Configuring a Cisco 827 Router to Support PPPoE Clients, Terminating on a Cisco 6400 UAC
Configuring a Cisco 827 Router to Support PPPoE Clients, Terminating on a Cisco 6400 UAC Document ID: 12889 Contents Introduction Before You Begin Conventions Prerequisites Components Used Configure Network
Cisco DSL Router Configuration and Troubleshooting Guide Cisco DSL Router Acting as a PPPoE Client with a Dynamic IP Address
Cisco DSL Router Configuration and Troubleshooting Guide Cisco DSL Router Acting as a PPPoE Client with a Dynamic IP Address Document ID: 71118 Contents Introduction Prerequisites Requirements Components
Configuring the Cisco 827 Router as a PPPoE Client With NAT
Configuring the Cisco 827 Router as a PPPoE Client With NAT Document ID: 8514 Contents Introduction Prerequisites Requirements Components Used Conventions Configure Network Diagram Configurations Verify
Configuring Dynamic Multipoint VPN Using GRE Over IPsec With OSPF, NAT, and Cisco IOS Firewall
Configuring Dynamic Multipoint VPN Using GRE Over IPsec With OSPF, NAT, and Cisco IOS Firewall Document ID: 43068 Contents Introduction Prerequisites Requirements Components Used Conventions Configure
Configuring PPP over ATM with NAT
CHAPTER 4 The Cisco Secure Router 520 ADSL-over-POTS and Cisco Secure Router 520 ADSL-over-ISDN routers support Point-to-Point Protocol over Asynchronous Transfer Mode (PPPoA) clients and network address
Use NAT to Hide the Real IP Address of CTC to Establish a Session with ONS 15454
Use NAT to Hide the Real IP Address of CTC to Establish a Session with ONS 15454 Document ID: 65122 Contents Introduction Prerequisites Requirements Components Used Conventions Background Information Topology
EHWIC-4SHDSL-EA module Fixed ISR G2 routers like C888EA-K9 work in both CO and CPE modes with Cisco IOS Software 15.2(2)T2 and later releases.
Contents Introduction Prerequisites Requirements Components Used Configure Configurations ATM mode EFM mode Introduction This document describes configuration steps required to implement a back-to-back
Policy Based Routing with the Multiple Tracking Options Feature Configuration Example
Policy Based Routing with the Multiple Tracking Options Feature Configuration Example Document ID: 48003 Contents Introduction Prerequisites Requirements Components Used Conventions Configure Network Diagram
Cisco PPPoE Baseline Architecture for the Cisco UAC 6400
Cisco PPPoE Baseline Architecture for the Cisco UAC 6400 Document ID: 12915 Contents Introduction Assumption Technology Brief Advantages and Disadvantages of PPPoE Architecture Advantages Disadvantages
Configuring Layer 2 Tunneling Protocol (L2TP) over IPSec
Configuring Layer 2 Tunneling Protocol (L2TP) over IPSec Document ID: 14122 Introduction Prerequisites Requirements Components Used Conventions Configure Network Diagram Configurations Verify Troubleshoot
Cisco DSL Router Configuration and Troubleshooting Guide Step by Step Configuration of RFC1483 Pure Bridging
Cisco DSL Router Configuration and Troubleshooting Guide Step by Step Configuration of RFC1483 Pure Bridging Document ID: 71128 Contents Introduction Prerequisites Requirements Components Used Conventions
Configuring IOS to IOS IPSec Using AES Encryption
Configuring IOS to IOS IPSec Using AES Encryption Document ID: 43069 Contents Introduction Prerequisites Requirements Components Used Conventions Configure Configurations Verify Troubleshoot Troubleshooting
Configuring PPPoE Client on the Cisco 2600 to Connect to a Non Cisco DSL CPE
Configuring PPPoE Client on the Cisco 2600 to Connect to a Non Cisco DSL CPE Document ID: 4105 Contents Introduction Prerequisites Requirements Components Used Conventions Configure Network Diagram Configurations
isco Cisco PPPoE Baseline Architecture for the Cisco UAC
isco Cisco PPPoE Baseline Architecture for the Cisco UAC Table of Contents Cisco PPPoE Baseline Architecture for the Cisco UAC 6400...1...1 Introduction...1 Assumption...1 Technology Brief...2 Advantages
IOS Router : Easy VPN (EzVPN) in Network Extension Mode (NEM) with Split tunnelling Configuration Example
IOS Router : Easy VPN (EzVPN) in Network Extension Mode (NEM) with Split tunnelling Configuration Example Document ID: 63098 Contents Introduction Prerequisites Requirements Components Used Conventions
How to Configure a Cisco Router Behind a Non-Cisco Cable Modem
How to Configure a Cisco Router Behind a Non-Cisco Cable Modem Document ID: 19268 Contents Introduction Prerequisites Requirements Components Used Conventions Configure Network Diagram Configurations Verify
SSG Configuration Example
APPENDIX A Example A-1 is a sample SSG configuration for the Cisco 10000 series router based on the topology in Figure A-1. The configuration includes AAA, PPP, SSG, and RADIUS. The SSG configuration enables
Configuring PPP over ATM with NAT
This chapter provides an overview of Point-to-Point Protocol over Asynchronous Transfer Mode (PPPoA) clients and network address translation (NAT) that can be configured on the Cisco 860 and Cisco 880
Access Server Dial In IP/PPP Configuration With Dedicated V.120 PPP
Access Server Dial In IP/PPP Configuration With Dedicated V.120 PPP Document ID: 6306 Contents Introduction Prerequisites Requirements Components Used Conventions Background Information How V.120 Affects
Using NAT in Overlapping Networks
Using NAT in Overlapping Networks Document ID: 13774 Contents Introduction Prerequisites Requirements Components Used Conventions Configure Network Diagram Configurations Verify Troubleshoot Related Information
NAT Support for Multiple Pools Using Route Maps
NAT Support for Multiple Pools Using Route Maps Document ID: 13739 Contents Introduction Prerequisites Requirements Components Used Conventions Background Information Access List Approach Host 1 to Host
ISDN Authentication and Callback with Caller ID
ISDN Authentication and Callback with Caller ID Document ID: 15925 Contents Introduction Prerequisites Requirements Components Used Conventions Background Information Configure Network Diagram Configurations
DHCP Client on WAN Interfaces
DHCP Client on WAN Interfaces First Published: February 25, 2002 Last Updated: September 12, 2008 The DHCP Client on WAN Interfaces feature extends the Dynamic Host Configuration Protocol (DHCP) to allow
QoS: Classification, Policing, and Marking on LAC Configuration Guide, Cisco IOS Release 12.4T
QoS: Classification, Policing, and Marking on LAC Configuration Guide, Cisco IOS Release 12.4T Americas Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA http://www.cisco.com
Configuring Virtual Asynchronous Traffic over ISDN
Configuring Virtual Asynchronous Traffic over ISDN Cisco IOS software offers two solutions to send virtual asynchronous traffic over ISDN: Using International Telecommunication Union Telecommunication
PPPoA Baseline Architecture
PPPoA Baseline Architecture Document ID: 12914 Contents Introduction Assumption Technology Brief Advantages and Disadvantages of PPPoA Architecture Advantages Disadvantages Implementation Considerations
RADIUS Logical Line ID
The feature, also known as the Logical Line Identification (LLID) Blocking feature enables administrators to track their customers on the basis of the physical lines on which customer calls originate.
How to configure MB5000 Serial Port Bridge mode
How to configure MB5000 Serial Port Bridge mode MB5000 has a configurable serial port. With this serial port, MB5000 can be used as DCE device to be connected with Cisco router s console port so that MB5000
cable modem dhcp proxy nat on Cisco Cable Modems
cable modem dhcp proxy nat on Cisco Cable Modems Document ID: 12176 Contents Introduction Prerequisites Requirements Components Used Conventions Dynamic NAT Versus Static NAT Configuration Using cable
PPPoE Session Limit per NAS Port
PPPoE Session Limit per NAS Port First Published: March 17, 2003 Last Updated: February 28, 2006 The PPPoE Session Limit per NAS Port feature enables you to limit the number of PPP over Ethernet (PPPoE)
Define Interface Policy-Map AV Pairs AAA
First Published: November 11, 2004 Last Published: July 29, 2009 The feature introduces two Cisco RADIUS vendor-specific attributes (VSAs) that allow a new policy map to be applied or an existing policy
Configuring a Terminal/Comm Server
Configuring a Terminal/Comm Server Document ID: 5466 Introduction Prerequisites Requirements Components Used Conventions Cabling Design Strategy Configure Network Diagram Configurations Command Summary
Fixing Issues with Corporate Directory Lookup from the Cisco IP Phone
Fixing Issues with Corporate Directory Lookup from the Cisco IP Phone Document ID: 13936 Contents Introduction Prerequisites Requirements Components Used Conventions Fix Corporate Directory Issues in Cisco
Broadband Access Aggregation and DSL Configuration Guide, Cisco IOS XE Release 3S
Broadband Access Aggregation and DSL Configuration Guide, Cisco IOS XE Release 3S Americas Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA http://www.cisco.com Tel: 408
IDSL Overview. Contents. Prerequisites. Document ID: Requirements
IDSL Overview Document ID: 7911 Contents Introduction Prerequisites Requirements Components Used Conventions Configure a CPE for a Remote User Network Diagram Step by Step Instructions Configure the Telco
OSPF Routers Connected by a Point to Multipoint Link
OSPF Routers Connected by a Point to Multipoint Link Document ID: 47862 Contents Introduction Prerequisites Requirements Components Used Conventions Configure Network Diagram Configurations Verify Examine
Configuring the Cisco Router and VPN Clients Using PPTP and MPPE
Configuring the Cisco Router and VPN Clients Using PPTP and MPPE Document ID: 29781 Contents Introduction Prerequisites Requirements Components Used Network Diagram Conventions PPTP Router Configuration
VoIP with Channel Associated Signaling (CAS)
VoIP with Channel Associated Signaling (CAS) Document ID: 14078 Contents Introduction Prerequisites Requirements Components Used Related Products Conventions T1 Signaling: CCS and CAS CCS CAS Configure
IPsec Anti-Replay Window: Expanding and Disabling
IPsec Anti-Replay Window: Expanding and Disabling First Published: February 28, 2005 Last Updated: March 24, 2011 Cisco IP security (IPsec) authentication provides anti-replay protection against an attacker
Define Interface Policy-Map AV Pairs AAA
The feature introduces two Cisco RADIUS vendor-specific attributes (VSAs) that allow a new policy map to be applied or an existing policy map to be modified, without affecting its session, during a Point-to-Point
IPsec Anti-Replay Window Expanding and Disabling
IPsec Anti-Replay Window Expanding and Disabling Cisco IP security (IPsec) authentication provides anti-replay protection against an attacker duplicating encrypted packets by assigning a unique sequence
Configuring Cisco CallManager IP Phones to Work With IP Phone Agent
Configuring Cisco CallManager IP Phones to Work With IP Phone Agent Document ID: 40564 Contents Introduction Prerequisites Requirements Components Used Conventions Configuration Procedures in Cisco CallManager
LANE, CES, and VBR PVCs in Shaped VP Tunnels
LANE, CES, and VBR PVCs in Shaped VP Tunnels Document ID: 10493 Contents Introduction Prerequisites Requirements Components Used Conventions Assumptions Configure Network Diagram Configurations Troubleshoot
Provisioning Broadband Aggregators Topics
CHAPTER 7 The Cisco Broadband Access Center software enables you to provision services on broadband aggregators. Provisioning occurs after you create administrative networks and network devices. See Chapter
Point-to-Point Protocol (PPP)
Point-to-Point Protocol (PPP) Accessing the WAN Chapter 2 Version 4.0 2006 Cisco Systems, Inc. All rights reserved. Cisco Public 1 Objectives Describe the fundamental concepts of point-to-point serial
Cisco Configuring Hub and Spoke Frame Relay
Table of Contents Configuring Hub and Spoke Frame Relay...1 Introduction...1 Before You Begin...1 Conventions...1 Prerequisites...1 Components Used...1 Configure...1 Network Diagram...2 Configurations...2
Lab 8.5.2: Troubleshooting Enterprise Networks 2
Lab 8.5.2: Troubleshooting Enterprise Networks 2 Topology Diagram Addressing Table Device Interface IP Address Subnet Mask Default Gateway Fa0/0 192.168.10.1 255.255.255.0 N/A R1 Fa0/1 192.168.11.1 255.255.255.0
PPP over Frame Relay
The feature allows a router to establish end-to-end Point-to-Point Protocol (PPP) sessions over Frame Relay. Finding Feature Information, page 1 Prerequisites for, page 1 Restrictions for, page 2 Information
Point-to-Point Protocol (PPP) Accessing the WAN Chapter 2
Point-to-Point Protocol (PPP) Accessing the WAN Chapter 2 ITE I Chapter 6 2006 Cisco Systems, Inc. All rights reserved. Cisco Public 1 Objectives Describe the fundamental concepts of point-to-point serial
PPPoE Session Limits per NAS Port
PPPoE Session Limits per NAS Port The PPPoE Session Limit per NAS Port feature enables you to limit the number of PPP over Ethernet (PPPoE) sessions on a specific permanent virtual circuit (PVC) or VLAN
Cisco Press CCIE Practical Studies CCIE Practice Lab: Unnamed Solutions
Cisco Press CCIE Practical tudies CCIE Practice Lab: olutions olutions brought to you by a division of kyline Computer Corporation CCIE Practical tudies Cisco Press CCIE Practical tudies CCIE Practice
Autosense for ATM PVCs and MUX SNAP Encapsulation
Autosense for ATM PVCs and MUX SNAP Encapsulation The PPPoA/PPPoE Autosense for ATM PVCs feature enables a router to distinguish between incoming PPP over ATM (PPPoA) and PPP over Ethernet (PPPoE) over
Finding Feature Information
The feature provides PPP over Ethernet (PPPoE) client support on routers. PPPoE is a commonly used application in the deployment of digital subscriber lines (DSLs). The PPP over Ethernet Client feature
Understanding and Troubleshooting Idle Timeouts
Understanding and Troubleshooting Idle Timeouts Document ID: 23423 Contents Introduction Prerequisites Requirements Components Used Conventions Common Problems and Symptoms Idle Timeouts Interesting Traffic
Broadband Access Aggregation and DSL Configuration Guide, Cisco IOS XE Fuji 16.7.x
Broadband Access Aggregation and DSL Configuration Guide, Cisco IOS XE Fuji 16.7.x Americas Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA http://www.cisco.com Tel:
Broadband Access Aggregation and DSL Configuration Guide, Cisco IOS XE Fuji 16.8.x
Broadband Access Aggregation and DSL Configuration Guide, Cisco IOS XE Fuji 16.8.x Americas Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA http://www.cisco.com Tel:
Three interface Router without NAT Cisco IOS Firewall Configuration
Three interface Router without NAT Cisco IOS Firewall Configuration Document ID: 13893 Contents Introduction Prerequisites Requirements Components Used Conventions Configure Network Diagram Configurations
Default Gateway Fa0/ N/A. Device Interface IP Address Subnet Mask
Felix Rohrer Topology Addressing Table Device Interface IP Address Subnet Mask Default Gateway Fa0/1 10.0.0.1 255.255.255.128 N/A S0/0/0 172.16.0.1 255.255.255.252 N/A S0/0/1 172.16.0.9 255.255.255.252
Secure ACS Database Replication Configuration Example
Secure ACS Database Replication Configuration Example Document ID: 71320 Introduction Prerequisites Requirements Components Used Related Products Conventions Background Information Scenario I Scenario
Configuration Examples
APPENDIX A This appendix shows some examples of the configuration in the Cisco 2600 series, Cisco 3600 series, and Cisco 3700 series routers Cisco 2600 Series Router Configuration Example Following is
Using an ADTRAN Terminal Adapter with Cisco Routers
Using an ADTRAN Terminal Adapter with Cisco Routers Document ID: 28080 Contents Introduction Prerequisites Requirements Components Used Conventions Dialing Method V.25 or V.25bis Dialing DTR Dialing Keypad
QoS in a SOHO Virtual Private Network for IP Telephony
CHAPTER 5 QoS in a SOHO Virtual Private Network for Telephony This chapter provides information about implementing QoS in an AVVID-enabled Small Office Home Office (SOHO) Virtual Private Network (VPN)
Configuring IDS TCP Reset Using VMS IDS MC
Configuring IDS TCP Reset Using VMS IDS MC Document ID: 47560 Contents Introduction Prerequisites Requirements Components Used Conventions Configure Network Diagram Configurations Initial Sensor Configuration
Configuring Redundant Routing on the VPN 3000 Concentrator
Configuring Redundant Routing on the VPN 3000 Concentrator Document ID: 13354 Contents Introduction Prerequisites Requirements Components Used Conventions Configure Network Diagram Router Configurations
management server password through sessions throttle
management server password through sessions throttle management server password, page 4 management server url, page 5 max bandwidth, page 6 max vc, page 7 multihop-hostname, page 8 nas-port-id format c,
IPv6 and xdsl. Athanassios Liakopoulos Slovenian IPv6 Training, Ljubljana, May 2010
IPv6 and xdsl Athanassios Liakopoulos (aliako@grnet.gr) Slovenian IPv6 Training, Ljubljana, May 2010 Copy... Rights This slide set is the ownership of the 6DEPLOY project via its partners The Powerpoint
Broadband Access Aggregation and DSL Configuration Guide, Cisco IOS XE Release 3S (ASR 1000)
Broadband Access Aggregation and DSL Configuration Guide, Cisco IOS XE Release 3S (ASR 1000) Americas Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA http://www.cisco.com
802.1P CoS Bit Set for PPP and PPPoE Control Frames
802.1P CoS Bit Set for PPP and PPPoE Control The 802.1P CoS Bit Set for PPP and PPPoE Control feature provides the ability to set user priority bits in the IEEE 802.1Q tagged frame to allow traffic prioritization.
Tactical Software requires that Cisco IOS Software Release 12.0(9) or later be installed on the NAS to interoperate with DialOut/EZ.
Products & Services Using Dialout/EZ with a Cisco Access Server Document ID: 23241 Contents Introduction Prerequisites Requirements Components Used Conventions Installation and Configuration Installing
Configuring PPP Callback
Configuring PPP Callback This chapter describes how to configure PPP callback for dial-on-demand routing (DDR). It includes the following main sections: PPP Callback for DDR Overview How to Configure PPP
L2TP IPsec Support for NAT and PAT Windows Clients
L2TP IPsec Support for NAT and PAT Windows Clients The L2TP IPsec Support for NAT and PAT Windows Clients feature allows mulitple Windows client to connect to an IPsec-enabled Cisco IOS Layer 2 Tunneling
Preserve 802.1Q Tagging with 802.1P Marking over ATM PVCs for xdsl Uplinks
Preserve 802.1Q Tagging with 802.1P Marking over ATM PVCs for xdsl Uplinks First Published: October 21, 2009 Last Updated: Sept 17, 2010 The Preserve 802.1Q Tagging with 802.1P Marking over ATM PVCs for
PPPoE on ATM. Finding Feature Information. Prerequisites for PPPoE on ATM. Restrictions for PPPoE on ATM
This feature module describes the PPP over Ethernet (PPPoE) on ATM feature. The feature provides the ability to connect a network of hosts over a simple bridging-access device to a remote access concentrator.
Cisco - Connecting Routers Back-to-Back Through the AUX Ports using a Rollover Cable
1 of 5 6/12/2001 1:43 PM Connecting Routers Back-to-Back Through the AUX Ports using a Rollover Cable Contents Introduction Conventions Network Diagram Configurations Troubleshooting the Configuration
Configuring the Physical Subscriber Line for RADIUS Access and Accounting
Configuring the Physical Subscriber Line for RADIUS Access and Accounting Configuring a physical subscriber line for RADIUS Access and Accounting enables an L2TP access concentrator (LAC) and an L2TP network
Implementing ADSL and Deploying Dial Access for IPv6
Implementing ADSL and Deploying Dial Access for IPv6 Last Updated: July 31, 2012 Finding Feature Information, page 1 Restrictions for Implementing ADSL and Deploying Dial Access for IPv6, page 1 Information
Cisco Press CCIE Practical Studies CCIE Practice Lab: Enchilada Solutions
Cisco Press CCIE Practical Studies CCIE Practice Lab: Solutions Cisco Press CCIE Practical Studies CCIE Practice Lab: LAB Book Chapter Book Page The 18 1161 Overview... 3 Technical Details... 3 Table 54-1:
Configuring Catalyst Switches for Polycom Conference Phones
Configuring Catalyst Switches for Polycom Conference Phones Document ID: 97229 Contents Introduction Prerequisites Requirements Components Used Related Products Conventions Background Information Configure
Cisco Back to Back Frame Relay
Table of Contents Back to Back Frame Relay...1 Introduction...1 Before You Begin...1 Conventions...1 Prerequisites...1 Components Used...1 Configure...2 Network Diagram...2 Configurations...2 Verify...3
VPN Connection through Zone based Firewall Router Configuration Example
VPN Connection through Zone based Firewall Router Configuration Example Document ID: 112051 Contents Introduction Prerequisites Requirements Components Used Conventions Background Information Configure
CCNA 4 - Final Exam (A)
CCNA 4 - Final Exam (A) 1. A network administrator is asked to design a system to allow simultaneous access to the Internet for 250 users. The ISP for this network can only supply five public IPs. What
Configuring IOS Server Load Balancing with HTTP Probes in the Dispatched Mode
Configuring IOS Server Load Balancing with HTTP Probes in the Dispatched Mode Document ID: 15055 Contents Introduction Prerequisites Requirements Components Used Conventions Configure HTTP Probes Network
Autosense of MUX/SNAP Encapsulation and PPPoA/PPPoE on ATM PVCs
Autosense of MUX/SNAP Encapsulation and PPPoA/PPPoE on ATM PVCs Feature History for Autosense of MUX/SNAP Encapsulation and PPPoA/PPPoE on ATM PVCs Release Modification 12.2(15)B This feature was introduced.
LAN to LAN IPsec Tunnel Between a Cisco VPN 3000 Concentrator and Router with AES Configuration Example
LAN to LAN IPsec Tunnel Between a Cisco VPN 3000 Concentrator and Router with AES Configuration Example Document ID: 26402 Contents Introduction Prerequisites Requirements Components Used Conventions Configure
Configuring the PIX Firewall and VPN Clients Using PPTP, MPPE and IPSec
Configuring the PIX Firewall and VPN Clients Using PPTP, MPPE and IPSec Document ID: 14095 Contents Introduction Prerequisites Requirements Components Used Conventions Configure Network Diagram Configurations
Lab Troubleshooting Basic PPP with Authentication Topology
Topology 2013 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 1 of 8 Addressing Table Objectives Device Interface IP Address Subnet Mask Default Gateway R1 G0/1 192.168.1.1
Configuring and Troubleshooting Dialer Profiles
Configuring and Troubleshooting Dialer Profiles Document ID: 10219 Contents Introduction Prerequisites Requirements Components Used Conventions Background Information Are Dialer Profiles Right for You?
Configuring PPP over Ethernet with NAT
CHAPTER 3 The Cisco Secure Router 520 Ethernet-to-Ethernet routers support Point-to-Point Protocol over Ethernet (PPPoE) clients and network address translation (NAT). Multiple PCs can be connected to
TACACS+ on an Aironet Access Point for Login Authentication Configuration Example
TACACS+ on an Aironet Access Point for Login Authentication Configuration Example Document ID: 70149 Contents Introduction Prerequisites Requirements Components Used Conventions Configure Network Diagram
Configuring Transparent and Proxy Media Redirection Using ACNS Software 4.x
Configuring Transparent and Proxy Media Redirection Using ACNS Software 4.x Document ID: 4717 Contents Introduction Before You Begin Conventions Prerequisites Requirements Components Used Configure Network
Communication Media Module IP Connectivity
Communication Media Module IP Connectivity Document ID: 91263 Contents Introduction Prerequisites Requirements Components Used Conventions Background Information Configure Configurations Packet Flow Troubleshoot
Configuring the Physical Subscriber Line for RADIUS Access and Accounting
Configuring the Physical Subscriber Line for RADIUS Access and Accounting Last Updated: December 5, 2011 Configuring a physical subscriber line for RADIUS Access and Accounting enables an L2TP access concentrator
Configuration Professional: Site to Site IPsec VPN Between Two IOS Routers Configuration Example
Configuration Professional: Site to Site IPsec VPN Between Two IOS Routers Configuration Example Document ID: 113337 Contents Introduction Prerequisites Requirements Components Used Conventions Configuration
G.SHDSL Symmetric DSL Support for Cisco IAD2420 Series IAD
G.SHDSL Symmetric DSL Support for Cisco IAD2420 Series IAD This document describes the Multirate Symmetrical High-Speed Digital Subscriber Line (G.SHDSL) feature supported on the Cisco IAD2420 series integrated
This document provides a sample configuration for X25 Over TCP.
X.25 over TCP/IP Document ID: 9363 Contents Introduction Prerequisites Requirements Components Used Conventions Background Information Configure Network Diagram Configurations Verify Troubleshoot Troubleshooting
G.SHDSL Symmetric DSL Support for Cisco IAD2420 Series IAD
G.SHDSL Symmetric DSL Support for Cisco IAD2420 Series IAD This document describes the Multirate Symmetrical High-Speed Digital Subscriber Line (G.SHDSL) feature supported on the Cisco IAD2420 series integrated
Configuring the VPN Client 3.x to Get a Digital Certificate
Configuring the VPN Client 3.x to Get a Digital Certificate Document ID: 4302 Contents Introduction Prerequisites Requirements Components Used Conventions Configure the VPN Client Verify Troubleshoot Related
Juniper Networks Certified Internet Associate (JNCIA- E)
Juniper JN0-120 Juniper Networks Certified Internet Associate (JNCIA- E) Version: 4.0 Topic 1, Volume A QUESTION NO: 1 By default, how does the router handle changes to its operational configuration? A.
Configuring Network Side ISDN BRI Voice Interface Cards
Configuring Network Side ISDN BRI Voice Interface Cards Document ID: 15415 Contents Introduction Prerequisites Requirements Components Used Conventions Background Information Configure Configure the VIC
Configure Q.SIG PRI Trunks between Call Manager and Avaya S8700/G650 with Unity Voice Mail Integration
Configure Q.SIG PRI Trunks between Call Manager and Avaya S8700/G650 with Unity Voice Mail Integration Document ID: 63790 Contents Introduction Prerequisites Requirements Components Used Conventions Test