Performance Monitoring and Alarm Guide

Transcription

1 AudioCodes One Voice Operations Center EMS, SEM and IP Phones Management Performance Monitoring and Alarm Guide Mediant 1000B Gateway and E-SBC Version 7.0 Document #: LTRT-94954

2

3 Performance Monitoring and Alarm Guide Contents Contents 1 Introduction Performance Monitoring Parameters Frame: Gateway System Monitoring (Configuration) Tab: System IP Tab: VoP Call Statistics Tab: SIP IP to Tel Tab: SIP Tel to IP Tab: Trunk Statistics Tab: SRD Statistics Tab: IP Group Statistics Tab: Trunk Group Statistics Frame: Gateway System Monitoring (History) Tab: System IP Tab: VoP Call Statistics Tab: SIP IP to Tel Tab: SIP Tel to IP Frame: Gateway System Monitoring (Real-Time) Tab: System IP Tab: VoP Call Statistics Tab: SIP IP to Tel Tab: SIP Tel to IP Frame: IP Group Monitoring (History) Tab: IP Group Statistics Frame: IP Group Monitoring (Real-Time) Tab: IP Group Statistics Frame: SRD Monitoring (History) Tab: SRD Statistics Frame: SRD Monitoring (Real-Time) Tab: SRD Statistics Frame: System Monitoring SIP (Configuration) Tab: System IP Tab: VoP Call Statistics Tab: SIP IP to Tel Tab: SIP Tel to IP Tab: SRD Statistics Tab: IP Group Statistics Tab: Trunk Group Statistics Frame: Trunk Group Monitoring (History) Tab: Trunk Group Statistics Frame: Trunk Group Monitoring (Real-Time) Tab: Trunk Group Statistics Frame: Trunk Monitoring (History) Tab: Trunk Performance Frame: Trunk Monitoring (Real-Time) Tab: Trunk Performance Version Performance Monitoring and Alarms

4 Mediant 1000B Gateway and E-SBC 3 Alarms Standard Traps Cold Start Link Down Link Up Authentication Failure DS1 Line Status EMS Alarms EMS Trap Receiver Binding Error GW Connection Alarm GW Mismatch Alarm EMS Server Started Disk Space Alarm Software Replaced Hardware Replaced HTTP/HTTPS Access Disabled PM File Generated PM Polling Error Cold Start Missed Security Alarm Security Event Topology Update Event Topology File Event Synchronizing Alarms Event Synchronizing Active Alarms Event License Key Alarm Alarm Supression Alarm EMS Keep Alive Alarm Pre-provisioning Alarm SEM Alarms SEM Failed Calls Alarm SEM Voice Quality Alarm SEM Average Call Duration Alarm SEM License Key Alarm SEM System Load Alarm SEM Call Details Storage Level has Changed SEM Time Synchronization Alarm SEM AD Lync Connection Alarm SEM MS Lync AD Server Alarm SEM Rule Bandwidth Alarm SEM Rule Max Concurrent Calls Alarm IP Phone Alarms Registration Failure Alarm Lync Survivable Mode Start Alarm Lync Login Failure Alarm Device Alarms Board Fatal Error Configuration Error Temperature Alarm Initialization Ended Board Resetting Following Software Reset Performance Monitoring and Alarm Guide 4 Document #: LTRT-94954

5 Performance Monitoring and Alarm Guide Contents Feature Key Related Error Gateway Administrative State Changed No Free Channels Available Gatekeeper/Proxy not Found or Registration Failed Ethernet Link Down Alarm System Component Overloaded Active Alarms Table Overflow Operational State Change Keep Alive Trap NAT Traversal Alarm Threshold of Performance Monitored Object Exceeded HTTP Download Result Fan Tray Alarm Power Supply Alarm D-Channel Status Dial Plan File Replaced Trap Analog Port SPI Out of Service Analog Port High Temperature Trunk LOS Alarm Trunk LOF Alarm Trunk AIS Alarm Trunk RAI Alarm IPv SAS Emergency Mode Alarm NTP Server Status Alarm LDAP Lost Connection Analog Port Ground Fault Out of Service SSH Connection Status [Event] OCSP Server Status Alarm Power over Ethernet Status [Event] Media Process Overload Alarm Wireless Cellular Modem Alarm NFAS Group Alarm B Channel Alarm Ethernet Group Alarm Media Realm BW Threshold Alarm Certificate Expiry Notification Web User Access Disabled Proxy Connection Lost Redundant Board Alarm IDS Policy Alarm IDS Threshold Cross Notification IDS Blacklist Notification Proxy Connectivity Web User Activity Log Trap Version Performance Monitoring and Alarms

6 Mediant 1000B Gateway and E-SBC This page is intentionally left blank. Performance Monitoring and Alarm Guide 6 Document #: LTRT-94954

7 Performance Monitoring and Alarm Guide Notices Notice This document describes the Performance Monitoring parameters and alarms for the Mediant 1000B Gateway and E-SBC product. Information contained in this document is believed to be accurate and reliable at the time of printing. However, due to ongoing product improvements and revisions, AudioCodes cannot guarantee accuracy of printed material after the Date Published nor can it accept responsibility for errors or omissions. Updates to this document and other documents can be viewed by registered customers at AudioCodes Inc. All rights reserved This document is subject to change without notice. Date Published: June Trademarks AudioCodes, AC, AudioCoded, Ardito, CTI2, CTI², CTI Squared, HD VoIP, HD VoIP Sounds Better, InTouch, Mediant, MediaPack, NetCoder, Netrake, Nuera, Open Solutions Network, OSN, Stretto, TrunkPack, VMAS, VoicePacketizer, VoIPerfect, VoIPerfectHD, What s Inside Matters, Your Gateway To VoIP and 3GX are trademarks or registered trademarks of AudioCodes Limited. All other products or trademarks are property of their respective owners. WEEE EU Directive Customer Support Pursuant to the WEEE EU Directive, electronic and electrical waste must not be disposed of with unsorted waste. Please contact your local recycling authority for disposal of this product. Customer technical support and services are provided by AudioCodes or by an authorized AudioCodes Service Partner. For more information on how to buy technical support for AudioCodes products and for contact information, please visit our Web site at Abbreviations and Terminology Term MG 'Frame' and 'Screen'. Refers to the Media Gateway. Sometimes used interchangeably Version Performance Monitoring and Alarms

8 Mediant 1000B Gateway and E-SBC Related Documentation Manual Name Mediant 1000B Gateway and E-SBC User s Manual Element Management System (EMS) Server Installation, Operation and Maintenance Manual Element Management System (EMS) Release Notes Element Management System (EMS) Product Element Management System (EMS) OAMP Integration Guide Element Management System (EMS) User s Manual Session Experience Manager (SEM) User's Manual IP Phone Management Server Administrator's Manual Element Management System (EMS) Online Help Documentation Feedback AudioCodes continually strives to produce high quality documentation. If you have any comments (suggestions or errors) regarding this document, please fill out the Documentation Feedback form on our Web site at Performance Monitoring and Alarm Guide 8 Document #: LTRT-94954

9 Performance Monitoring and Alarm Guide 1. Introduction 1 Introduction This guide incorporates Performance Monitoring Parameters and Alarms for the Mediant 1000B Gateway and E-SBC product. Version Performance Monitoring and Alarms

10

11 Performance Monitoring and Alarm Guide 1. Introduction This page is intentionally left blank. Version June 2014

12

13 Performance Monitoring and Alarm Guide 2. Performance Monitoring Parameters 2 Performance Monitoring Parameters Customers are often faced with a complex VoIP network with little or no information on the status and capacities of each component in it. PM helps the system architect design a better network. PM helps operators discover malfunctioning devices before they start causing a problem on the production network. The system provides two types of performance measurements: Gauges: Gauges represent the current state of a PM parameter in the system. Gauges, unlike counters, can decrease in value, and like counters, can increase. Counters: Counters always increase in value and are cumulative. Counters, unlike gauges, never decrease in value unless the system is reset. The counters are then zeroed. Performance measurements are available for the EMS or for a 3rd party performance monitoring system through an SNMP interface. These measurements can be polled at scheduled intervals by an external poller or utility in a media server or another offdevice system. PM measurements can be divided into two main groups: Real-Time PM Measurements - supply the current value of the PM entity. When requested, the entity is sampled and the current value is received. History PM Measurements - supply statistical data of the PM entity during the last interval period. These measurements include the Average, Minimum and Maximum values of the entity during the last interval. The default interval length is 15 minutes. Figure 1: History PM Measurements History Performance is measured in a constant time interval of 15 minutes to which all elements in the network are synchronized. Intervals commence precisely every 15 minutes, for example, 12:00:00, 12:15:00, 12:30:00, 12:45:00, etc. This allows synchronization of several management systems to the same interval time frame. Note that the first interval after start-up is always shorter (in the example above, the first interval only lasts 6 minutes - so that a new interval can start exactly on the 15 minute interval, in this case 11:30:00). During the initial start-up interval i.e. 6 minutes in the example above, polling is not performed. Version Performance Monitoring and Alarms

14 Mediant 1000B Gateway and E-SBC 2.1 Frame: Gateway System Monitoring (Configuration) Tab: System IP Frame: Gateway System Monitoring (Configuration), Tab: System IP EMS Parameter Name RT / Hist Gauge / Counter Parameter Number of Outgoing KBytes Number of Incoming KBytes Number of Outgoing Pkts Number of Incoming Pkts Number of Incoming Discarded Pkts Counter Counts the total number of outgoing Kbytes (1000 bytes) from the interface during the last interval. Mib name: acpmnetutilkbytesvolumetx Counter Counts the total number of Kbytes (1000 bytes) received on the interface, including those received in error, during the last interval. Mib name: acpmnetutilkbytesvolumerx Counter Counts the total number of outgoing Packets from the interface during the last interval. Mib name: acpmnetutilpacketsvolumetx Counter Counts the total number of Packets received on the interface, including those received in error, during the last interval. Mib name: acpmnetutilpacketsvolumerx Counter Counts the total number of malformed IP Packets received on the interface during the last interval. These are packets which are corrupted or discarded due to errors in their IP headers, including bad checksums, version number mismatch, other format errors, time-tolive exceeded, errors discovered in processing their IP options, etc. Mib name: acpmnetutildiscardedpacketsval Performance Monitoring and Alarm Guide 14 Document #: LTRT-94954

15 Performance Monitoring and Alarm Guide 2. Performance Monitoring Parameters Tab: VoP Call Statistics Frame: Gateway System Monitoring (Configuration), Tab: VoP Call Statistics EMS Parameter Name RT / Hist Gauge / Counter Parameter Num of Active Contexts Avg Num of Active Contexts Min Num of Active Contexts Max Gauge Indicates the average number of voice calls connected on the gateway since the last clear. Mib name: acpmactivecontextcountaverage Gauge Indicates the minimum number of voice calls connected on the gateway since the last clear. Mib name: acpmactivecontextcountmin Gauge Indicates the maximum number of voice calls connected on the gateway since the last clear. Mib name: acpmactivecontextcountmax G711 Active Calls Avg Gauge Indicates the average number of G.711 calls present on the TPM. Mib name: acpmchannelspercoderaverageg711 G723 Active Calls Avg Gauge Indicates the average number of G.723 calls present on the TPM. This attribute is only displayed if the G.723 Codec is provisioned on the DSP template. Mib name: acpmchannelspercoderaverageg723 G728 Active Calls Avg Gauge Indicates the average number of G.728 calls present on the TPM. This attribute is only displayed if the G.728 Codec is provisioned on the DSP template. Mib name: acpmchannelspercoderaverageg728 G729a Active Calls Avg Gauge Indicates the average number of G.729a calls present on the TPM. This attribute is only displayed if the G.729a Codec is provisioned on the DSP. Mib name: acpmchannelspercoderaverageg729a G729e Active Calls Avg Gauge Indicates the average number of G.729e calls present on the TPM. This attribute is only displayed if the G.729e Codec is provisioned on the DSP template. Mib name: acpmchannelspercoderaverageg729e AMR Active Calls Avg Gauge Indicates the average number of AMR calls present on the TPM. This attribute is only displayed if the AMR Codec is provisioned on the DSP template. Mib name: acpmchannelspercoderaverageamr EVRC Active Calls Avg Gauge Indicates the average number of EVRC calls present on the TPM. This attribute is only displayed if the EVRC Codec is provisioned on the DSP template. Mib name: acpmchannelspercoderaverageevrc Rx RTP Packet Loss Max Tx RTP Packet Loss Max Gauge Indicates the Max Rx RTP Packet loss (reported by RTCP) per TPM, up to this point in time during the collection interval, as indicated by the time Interval. Mib name: acpmmodulertppacketlossrxmax Gauge Indicates the Max Tx RTP Packet loss (reported by RTCP) per TPM, up to this point in time during the collection interval, as indicated by the time Interval. Mib name: acpmmodulertppacketlosstxmax Version Performance Monitoring and Alarms

16 Mediant 1000B Gateway and E-SBC EMS Parameter Name RT / Hist Gauge / Counter Parameter RTP delay Average Gauge Indicates the average RTP packets delay per TPM, up to this point in time during the collection interval, as indicated by the time Interval. Mib name: acpmmodulepacketdelayaverage RTP delay Max Gauge Indicates the maximum RTP packets delay per TPM, up to this point in time during the collection interval, as indicated by the time Interval. Mib name: acpmmodulepacketdelaymax RTP delay Min Gauge Indicates the minimum RTP packets delay per TPM, up to this point in time during the collection interval, as indicated by the time Interval. Mib name: acpmmodulepacketdelaymin RTP jitter Average Gauge Indicates the average RTP packets jitter per TPM, up to this point in time during the collection interval, as indicated by the time Interval. Mib name: acpmmodulepacketjitteraverage RTP jitter Min Gauge Indicates the minimum RTP packets jitter per TPM, up to this point in time during the collection interval, as indicated by the time Interval. Mib name: acpmmodulepacketjittermin RTP jitter Max Gauge Indicates the maximum RTP packets jitter per TPM, up to this point in time during the collection interval, as indicated by the time Interval. Mib name: acpmmodulepacketjittermax Rx RTP Bytes Max Gauge Indicates the Max Tx RTP Bytes per TPM, up to this point in time during the collection interval, as indicated by the time Interval. Mib name: acpmmodulertpbytesrxmax Tx RTP Bytes Max Gauge Indicates the Max Rx RTP Bytes per TPM, up to this point in time during the collection interval, as indicated by the time Interval. Mib name: acpmmodulertpbytestxmax Rx RTP Packets Max Gauge Indicates the Max Rx RTP Packets per TPM, up to this point in time during the collection interval, as indicated by the time Interval. Mib name: acpmmodulertppacketsrxmax Tx RTP Packets Max Gauge Indicates the Max Tx RTP Packets per TPM, up to this point in time during the collection interval, as indicated by the time Interval. Mib name: acpmmodulertppacketstxmax RTCP XR Average Conversational R Factor Gauge Average conversational R factor. Mib name: rtcpxrhistoryavgrcq RTCP XR Maximum Conversational R Factor RTCP XR Minimum Conversational R Factor Gauge Maximum conversational R factor. Mib name: rtcpxrhistorymaxrcq Gauge Minimum conversational R factor. Mib name: rtcpxrhistoryminrcq Performance Monitoring and Alarm Guide 16 Document #: LTRT-94954

17 Performance Monitoring and Alarm Guide 2. Performance Monitoring Parameters Tab: SIP IP to Tel Frame: Gateway System Monitoring (Configuration), Tab: SIP IP to Tel EMS Parameter Name RT / Hist Gauge / Counter Parameter IP to Tel Number of Call Attempts IP to Tel Number of Established Calls IP to Tel Number of Calls Terminated due to a Busy Line IP to Tel Number of Calls Terminated due to No Answer IP to Tel Number of Calls Terminated due to Forward IP to Tel Number of Failed Calls due to No Route Counter Indicates the number of attempted calls for IP to Tel direction, during last interval. Mib name: acpmsipattemptedcallsvalip2tel Counter Indicates the number of established calls for IP to Tel direction, during last interval. Mib name: acpmsipestablishedcallsvalip2tel Counter Indicates the number of calls that failed as a result of a busy line for IP to Tel direction, during last interval. Mib name: acpmsipbusycallsvalip2tel Counter Indicates the number of calls that weren't answered for IP to Tel direction, during last interval. Mib name: acpmsipnoanswercallsvalip2tel Counter Indicates the number of calls that were terminated due to a call forward for IP to Tel direction, during last interval. Mib name: acpmsipforwardedcallsvalip2tel Counter Indicates the number of calls whose destinations weren't found for IP to Tel direction, during last interval. Mib name: acpmsipnoroutecallsvalip2tel IP to Tel Number of Failed Calls due to No Matched Capabilities IP to Tel Number of Failed Calls due to No Resources IP to Tel Number of Failed Calls due to Other reasons IP to Tel Fax Call Attempts IP to Tel Successful Fax Calls IP to Tel Average Call Duration [sec] Counter Indicates the number of calls that failed due to mismatched media server capabilities for IP to Tel direction, during last interval. Mib name: acpmsipnomatchcallsvalip2tel Counter Indicates the number of calls that failed due to unavailable resources or a media server lock for IP to Tel direction, during last interval. Mib name: acpmsipnoresourcescallsvalip2tel Counter This counter is incremented as a result of calls that fail due to reasons not covered by the other counters for IP to Tel direction, during last interval. Mib name: acpmsipfailcallsvalip2tel Counter Indicates the number of attempted fax calls for IP to Tel direction, during last interval. Mib name: acpmsipfaxattemptedcallsvalip2tel Counter Indicates the number of successful fax calls for IP to Tel direction, during last interval. Mib name: acpmsipfaxsuccesscallsvalip2tel Gauge Indicates the average call duration of established calls for IP to Tel direction, during last interval. Mib name: acpmsipcalldurationaverageip2tel Version Performance Monitoring and Alarms

18 Mediant 1000B Gateway and E-SBC Tab: SIP Tel to IP Frame: Gateway System Monitoring (Configuration), Tab: SIP Tel to IP EMS Parameter Name RT / Hist Gauge / Counter Parameter Tel to IP Number of Call Attempts Tel to IP Number of Established Calls Tel to IP Number of Calls Terminated due to a Busy Line Tel to IP Number of Calls Terminated due to No Answer Tel to IP Number of Calls Terminated due to Forward Tel to IP Number of Failed Calls due to No Route Counter Indicates the number of attempted calls for Tel to IP direction, during last interval. Mib name: acpmsipattemptedcallsvaltel2ip Counter Indicates the number of established calls for Tel to IP direction, during last interval. Mib name: acpmsipestablishedcallsvaltel2ip Counter Indicates the number of calls that failed as a result of a busy line for Tel to IP direction, during last interval. Mib name: acpmsipbusycallsvaltel2ip Counter Indicates the number of calls that weren't answered for Tel to IP direction, during last interval. Mib name: acpmsipnoanswercallsvaltel2ip Counter Indicates the number of calls that were terminated due to a call forward for Tel to IP direction, during last interval. Mib name: acpmsipforwardedcallsvaltel2ip Counter Indicates the number of calls whose destinations weren't found for Tel to IP direction, during last interval. Mib name: acpmsipnoroutecallsvaltel2ip Tel to IP Number of Failed Calls due to No Matched Capabilities Tel to IP Number of Failed Calls due to No Resources Tel to IP Number of Failed Calls due to Other reasons Tel to IP Fax Call Attempts Tel to IP Successful Fax Calls Tel to IP Average Call Duration [sec] Counter Indicates the number of calls that failed due to mismatched media server capabilities for Tel to IP direction, during last interval. Mib name: acpmsipnomatchcallsvaltel2ip Counter Indicates the number of calls that failed due to unavailable resources or a media server lock for Tel to IP direction, during last interval. Mib name: acpmsipnoresourcescallsvaltel2ip Counter This counter is incremented as a result of calls that fail due to reasons not covered by the other counters for Tel to IP direction, during last interval. Mib name: acpmsipfailcallsvaltel2ip Counter Indicates the number of attempted fax calls for Tel to IP direction, during last interval. Mib name: acpmsipfaxattemptedcallsvaltel2ip Counter Indicates the number of successful fax calls for Tel to IP direction, during last interval. Mib name: acpmsipfaxsuccesscallsvaltel2ip Gauge Indicates the average call duration of established calls for Tel to IP direction, during last interval. Mib name: acpmsipcalldurationaveragetel2ip Performance Monitoring and Alarm Guide 18 Document #: LTRT-94954

19 Performance Monitoring and Alarm Guide 2. Performance Monitoring Parameters Tab: Trunk Statistics Frame: Gateway System Monitoring (Configuration), Tab: Trunk Statistics EMS Parameter Name RT / Hist Gauge / Counter Parameter Trunk utilization Avg Gauge Indicates the Average of simultaneously busy DS0 channels on this Trunk up to this point in time during the collection interval, as indicated by the Time Interval. A busy channel is when the Physical DS0 Termination isn't in Null context or OOS. A Trunk is either E1 or T1. Mib name: acpmtrunkutilizationaverage Trunk utilization Min Gauge Indicates the Minimum of simultaneously busy DS0 channels on this Trunk up to this point in time during the collection interval, as indicated by the Time Interval. A busy channel is when the Physical DS0 Termination isn't in Null context or OOS. A Trunk is either E1 or T1. Mib name: acpmtrunkutilizationmin Trunk utilization Max Gauge Indicates the Maximum of simultaneously busy DS0 channels on this Trunk up to this point in time during the collection interval, as indicated by the Time Interval. A busy channel is when the Physical DS0 Termination isn't in Null context or OOS. A Trunk is either E1 or T1. Mib name: acpmtrunkutilizationmax Trunk Errored Seconds Gauge Indicates the number of Errored Seconds. Mib name: dsx1intervaless Trunk Controlled Slip Seconds Gauge Indicates the number of Controlled Slip Seconds. Mib name: dsx1intervalcsss Trunk Path Coding Violations Trunk Bursty Errored Seconds Gauge Indicates the number of Path Coding Violations. Mib name: dsx1intervalpcvs Gauge Indicates the number of Bursty Errored Seconds. Mib name: dsx1intervalbess Tab: SRD Statistics Frame: Gateway System Monitoring (Configuration), Tab: SRD Statistics EMS Parameter Name RT / Hist Gauge / Counter Parameter SIP SRD Dialogs Val Counter Value of gauge or counter. Mib name: acpmsipsrddialogsval SIP SRD Invite Dialogs Val Counter Value of gauge or counter. Mib name: acpmsipsrdinvitedialogsval SIP SRD Subscribe Dialogs Val Counter Value of gauge or counter. Mib name: acpmsipsrdsubscribedialogsval Version Performance Monitoring and Alarms

20 Mediant 1000B Gateway and E-SBC EMS Parameter Name RT / Hist Gauge / Counter Parameter SIP SRD Other Dialogs Val Counter Value of gauge or counter. Mib name: acpmsipsrdotherdialogsval Tab: IP Group Statistics Frame: Gateway System Monitoring (Configuration), Tab: IP Group Statistics EMS Parameter Name RT / Hist Gauge / Counter Parameter SIP IP Group Dialogs Val Counter Value of gauge or counter. Mib name: acpmsipipgroupdialogsval SIP IP Group Invite Dialogs Val Counter Value of gauge or counter. Mib name: acpmsipipgroupinvitedialogsval SIP IP Group Subscribe Dialogs Val SIP IP Group Other Dialogs Val SIP IP Group In Invite Dialogs SIP IP Group I nsubscribe Dialogs SIP IP Group Out Invite Dialogs SIP IP Group Out Subscribe Dialogs Counter Value of gauge or counter. Mib name: acpmsipipgroupsubscribedialogsval Counter Value of gauge or counter. Mib name: acpmsipipgroupotherdialogsval Counter Value of gauge or counter. Mib name: acpmsipipgroupininvitedialogsval Counter Value of gauge or counter. Mib name: acpmsipipgroupinsubscribedialogsval Counter Value of gauge or counter. Mib name: acpmsipipgroupoutinvitedialogsval Counter Value of gauge or counter. Mib name: acpmsipipgroupoutsubscribedialogsval SIP IP Group Invite Dialogs IP Average SIP IP Group Invite Dialogs IP Max SIP IP Group Invite Dialogs IP Min Gauge Value of gauge or counter. Mib name: acpmsipipgroupinvitedialogsaverage Gauge Value of gauge or counter. Mib name: acpmsipipgroupinvitedialogsmax Gauge Value of gauge or counter. Mib name: acpmsipipgroupinvitedialogsmin Performance Monitoring and Alarm Guide 20 Document #: LTRT-94954

21 Performance Monitoring and Alarm Guide 2. Performance Monitoring Parameters Tab: Trunk Group Statistics Frame: Gateway System Monitoring (Configuration), Tab: Trunk Group Statistics EMS Parameter Name RT / Hist Gauge / Counter Parameter Trunk Group Utilization (%) Trunk Group Utilization (channels) Gauge Value of gauge or counter. Mib name: acpmsiptrunkgrouppercentageutilizationval Gauge Value of gauge or counter. Mib name: acpmsiptrunkgrouputilizationval Tel to IP Trunk Group Established Calls Val IP to Tel Trunk Group Established Calls Val Counter Value of gauge or counter. Mib name: acpmsiptel2iptrunkgroupestablishedcallsval Counter Value of gauge or counter. Mib name: acpmsipip2teltrunkgroupestablishedcallsval No Resources Calls Gauge Value of gauge or counter. Mib name: acpmsiptrunkgroupnoresourcescallsval Average Call Duration (sec) Gauge Value of gauge or counter. Mib name: acpmsiptrunkgroupcalldurationaverage Total Call Duration (sec) Gauge Value of gauge or counter. Mib name: acpmsiptrunkgroupcalldurationtotal Trunk Group All Trunks Busy (sec) Counter Value of gauge or counter. Mib name: acpmsiptrunkgroupalltrunksbusyval All Trunks Busy (%) Gauge Value of gauge or counter. Mib name: acpmsiptrunkgroupalltrunksbusypercentageval 2.2 Frame: Gateway System Monitoring (History) Tab: System IP Frame: Gateway System Monitoring (History), Tab: System IP EMS Parameter Name RT / Hist Gauge / Counter Parameter Number of Outgoing KBytes Number of Incoming KBytes Counter Counts the total number of outgoing Kbytes (1000 bytes) from the interface during the last interval. Mib name: acpmnetutilkbytesvolumetx Counter Counts the total number of Kbytes (1000 bytes) received on the interface, including those received in error, during the last interval. Mib name: acpmnetutilkbytesvolumerx Version Performance Monitoring and Alarms

22 Mediant 1000B Gateway and E-SBC EMS Parameter Name RT / Hist Gauge / Counter Parameter Number of Outgoing Pkts Counter Counts the total number of outgoing Packets from the interface during the last interval. Mib name: acpmnetutilpacketsvolumetx Number of Incoming Pkts Counter Counts the total number of Packets received on the interface, including those received in error, during the last interval. Mib name: acpmnetutilpacketsvolumerx Number of Incoming Discarded Pkts Counter Counts the total number of malformed IP Packets received on the interface during the last interval. These are packets which are corrupted or discarded due to errors in their IP headers, including bad checksums, version number mismatch, other format errors, time-tolive exceeded, errors discovered in processing their IP options, etc. Mib name: acpmnetutildiscardedpacketsval Tab: VoP Call Statistics Frame: Gateway System Monitoring (History), Tab: VoP Call Statistics EMS Parameter Name RT / Hist Gauge / Counter Parameter Num of Active Contexts Avg Num of Active Contexts Min Num of Active Contexts Max Gauge Indicates the average number of voice calls connected on the gateway since the last clear. Mib name: acpmactivecontextcountaverage Gauge Indicates the minimum number of voice calls connected on the gateway since the last clear. Mib name: acpmactivecontextcountmin Gauge Indicates the maximum number of voice calls connected on the gateway since the last clear. Mib name: acpmactivecontextcountmax G711 Active Calls Avg Gauge Indicates the average number of G.711 calls present on the TPM. Mib name: acpmchannelspercoderaverageg711 G723 Active Calls Avg Gauge Indicates the average number of G.723 calls present on the TPM. This attribute is only displayed if the G.723 Codec is provisioned on the DSP template. Mib name: acpmchannelspercoderaverageg723 G728 Active Calls Avg Gauge Indicates the average number of G.728 calls present on the TPM. This attribute is only displayed if the G.728 Codec is provisioned on the DSP template. Mib name: acpmchannelspercoderaverageg728 G729a Active Calls Avg Gauge Indicates the average number of G.729a calls present on the TPM. This attribute is only displayed if the G.729a Codec is provisioned on the DSP. Mib name: acpmchannelspercoderaverageg729a Performance Monitoring and Alarm Guide 22 Document #: LTRT-94954

23 Performance Monitoring and Alarm Guide 2. Performance Monitoring Parameters EMS Parameter Name RT / Hist Gauge / Counter Parameter G729e Active Calls Avg Gauge Indicates the average number of G.729e calls present on the TPM. This attribute is only displayed if the G.729e Codec is provisioned on the DSP template. Mib name: acpmchannelspercoderaverageg729e AMR Active Calls Avg Gauge Indicates the average number of AMR calls present on the TPM. This attribute is only displayed if the AMR Codec is provisioned on the DSP template. Mib name: acpmchannelspercoderaverageamr EVRC Active Calls Avg Gauge Indicates the average number of EVRC calls present on the TPM. This attribute is only displayed if the EVRC Codec is provisioned on the DSP template. Mib name: acpmchannelspercoderaverageevrc Rx RTP Packet Loss Max Tx RTP Packet Loss Max Gauge Indicates the Max Rx RTP Packet loss (reported by RTCP) per TPM, up to this point in time during the collection interval, as indicated by the time Interval. Mib name: acpmmodulertppacketlossrxmax Gauge Indicates the Max Tx RTP Packet loss (reported by RTCP) per TPM, up to this point in time during the collection interval, as indicated by the time Interval. Mib name: acpmmodulertppacketlosstxmax RTP delay Average Gauge Indicates the average RTP packets delay per TPM, up to this point in time during the collection interval, as indicated by the time Interval. Mib name: acpmmodulepacketdelayaverage RTP delay Max Gauge Indicates the maximum RTP packets delay per TPM, up to this point in time during the collection interval, as indicated by the time Interval. Mib name: acpmmodulepacketdelaymax RTP delay Min Gauge Indicates the minimum RTP packets delay per TPM, up to this point in time during the collection interval, as indicated by the time Interval. Mib name: acpmmodulepacketdelaymin RTP jitter Average Gauge Indicates the average RTP packets jitter per TPM, up to this point in time during the collection interval, as indicated by the time Interval. Mib name: acpmmodulepacketjitteraverage RTP jitter Min Gauge Indicates the minimum RTP packets jitter per TPM, up to this point in time during the collection interval, as indicated by the time Interval. Mib name: acpmmodulepacketjittermin RTP jitter Max Gauge Indicates the maximum RTP packets jitter per TPM, up to this point in time during the collection interval, as indicated by the time Interval. Mib name: acpmmodulepacketjittermax Rx RTP Bytes Max Gauge Indicates the Max Tx RTP Bytes per TPM, up to this point in time during the collection interval, as indicated by the time Interval. Mib name: acpmmodulertpbytesrxmax Version Performance Monitoring and Alarms

24 Mediant 1000B Gateway and E-SBC EMS Parameter Name RT / Hist Gauge / Counter Parameter Tx RTP Bytes Max Gauge Indicates the Max Rx RTP Bytes per TPM, up to this point in time during the collection interval, as indicated by the time Interval. Mib name: acpmmodulertpbytestxmax Rx RTP Packets Max Gauge Indicates the Max Rx RTP Packets per TPM, up to this point in time during the collection interval, as indicated by the time Interval. Mib name: acpmmodulertppacketsrxmax Tx RTP Packets Max Gauge Indicates the Max Tx RTP Packets per TPM, up to this point in time during the collection interval, as indicated by the time Interval. Mib name: acpmmodulertppacketstxmax RTCP XR Average Conversational R Factor Gauge Average conversational R factor. Mib name: rtcpxrhistoryavgrcq RTCP XR Maximum Conversational R Factor RTCP XR Minimum Conversational R Factor Gauge Maximum conversational R factor. Mib name: rtcpxrhistorymaxrcq Gauge Minimum conversational R factor. Mib name: rtcpxrhistoryminrcq Tab: SIP IP to Tel Frame: Gateway System Monitoring (History), Tab: SIP IP to Tel EMS Parameter Name RT / Hist Gauge / Counter Parameter IP to Tel Number of Call Attempts IP to Tel Number of Established Calls IP to Tel Number of Calls Terminated due to a Busy Line IP to Tel Number of Calls Terminated due to No Answer IP to Tel Number of Calls Terminated due to Forward Counter Indicates the number of attempted calls for IP to Tel direction, during last interval. Mib name: acpmsipattemptedcallsvalip2tel Counter Indicates the number of established calls for IP to Tel direction, during last interval. Mib name: acpmsipestablishedcallsvalip2tel Counter Indicates the number of calls that failed as a result of a busy line for IP to Tel direction, during last interval. Mib name: acpmsipbusycallsvalip2tel Counter Indicates the number of calls that weren't answered for IP to Tel direction, during last interval. Mib name: acpmsipnoanswercallsvalip2tel Counter Indicates the number of calls that were terminated due to a call forward for IP to Tel direction, during last interval. Mib name: acpmsipforwardedcallsvalip2tel Performance Monitoring and Alarm Guide 24 Document #: LTRT-94954

25 Performance Monitoring and Alarm Guide 2. Performance Monitoring Parameters EMS Parameter Name RT / Hist Gauge / Counter Parameter IP to Tel Number of Failed Calls due to No Route Counter Indicates the number of calls whose destinations weren't found for IP to Tel direction, during last interval. Mib name: acpmsipnoroutecallsvalip2tel IP to Tel Number of Failed Calls due to No Matched Capabilities IP to Tel Number of Failed Calls due to No Resources IP to Tel Number of Failed Calls due to Other reasons IP to Tel Fax Call Attempts IP to Tel Successful Fax Calls IP to Tel Average Call Duration [sec] Counter Indicates the number of calls that failed due to mismatched media server capabilities for IP to Tel direction, during last interval. Mib name: acpmsipnomatchcallsvalip2tel Counter Indicates the number of calls that failed due to unavailable resources or a media server lock for IP to Tel direction, during last interval. Mib name: acpmsipnoresourcescallsvalip2tel Counter This counter is incremented as a result of calls that fail due to reasons not covered by the other counters for IP to Tel direction, during last interval. Mib name: acpmsipfailcallsvalip2tel Counter Indicates the number of attempted fax calls for IP to Tel direction, during last interval. Mib name: acpmsipfaxattemptedcallsvalip2tel Counter Indicates the number of successful fax calls for IP to Tel direction, during last interval. Mib name: acpmsipfaxsuccesscallsvalip2tel Gauge Indicates the average call duration of established calls for IP to Tel direction, during last interval. Mib name: acpmsipcalldurationaverageip2tel Tab: SIP Tel to IP Frame: Gateway System Monitoring (History), Tab: SIP Tel to IP EMS Parameter Name RT / Hist Gauge / Counter Parameter Tel to IP Number of Call Attempts Tel to IP Number of Established Calls Tel to IP Number of Calls Terminated due to a Busy Line Tel to IP Number of Calls Terminated due to No Answer Counter Indicates the number of attempted calls for Tel to IP direction, during last interval. Mib name: acpmsipattemptedcallsvaltel2ip Counter Indicates the number of established calls for Tel to IP direction, during last interval. Mib name: acpmsipestablishedcallsvaltel2ip Counter Indicates the number of calls that failed as a result of a busy line for Tel to IP direction, during last interval. Mib name: acpmsipbusycallsvaltel2ip Counter Indicates the number of calls that weren't answered for Tel to IP direction, during last interval. Mib name: acpmsipnoanswercallsvaltel2ip Version Performance Monitoring and Alarms

26 Mediant 1000B Gateway and E-SBC EMS Parameter Name RT / Hist Gauge / Counter Parameter Tel to IP Number of Calls Terminated due to Forward Tel to IP Number of Failed Calls due to No Route Counter Indicates the number of calls that were terminated due to a call forward for Tel to IP direction, during last interval. Mib name: acpmsipforwardedcallsvaltel2ip Counter Indicates the number of calls whose destinations weren't found for Tel to IP direction, during last interval. Mib name: acpmsipnoroutecallsvaltel2ip Tel to IP Number of Failed Calls due to No Matched Capabilities Tel to IP Number of Failed Calls due to No Resources Tel to IP Number of Failed Calls due to Other reasons Tel to IP Fax Call Attempts Tel to IP Successful Fax Calls Tel to IP Average Call Duration [sec] Counter Indicates the number of calls that failed due to mismatched media server capabilities for Tel to IP direction, during last interval. Mib name: acpmsipnomatchcallsvaltel2ip Counter Indicates the number of calls that failed due to unavailable resources or a media server lock for Tel to IP direction, during last interval. Mib name: acpmsipnoresourcescallsvaltel2ip Counter This counter is incremented as a result of calls that fail due to reasons not covered by the other counters for Tel to IP direction, during last interval. Mib name: acpmsipfailcallsvaltel2ip Counter Indicates the number of attempted fax calls for Tel to IP direction, during last interval. Mib name: acpmsipfaxattemptedcallsvaltel2ip Counter Indicates the number of successful fax calls for Tel to IP direction, during last interval. Mib name: acpmsipfaxsuccesscallsvaltel2ip Gauge Indicates the average call duration of established calls for Tel to IP direction, during last interval. Mib name: acpmsipcalldurationaveragetel2ip 2.3 Frame: Gateway System Monitoring (Real-Time) Tab: System IP Frame: Gateway System Monitoring (Real-Time), Tab: System IP EMS Parameter Name RT / Hist Gauge / Counter Parameter Number of Outgoing KBytes RT Gauge This attribute counts the Current total number of outgoing Kbytes (1000 bytes) from the interface, so far from the beginning of the current collection interval as indicated by time Interval. Mib name: acpmnetutilkbytestotaltx Performance Monitoring and Alarm Guide 26 Document #: LTRT-94954

27 Performance Monitoring and Alarm Guide 2. Performance Monitoring Parameters EMS Parameter Name RT / Hist Gauge / Counter Parameter Number of Incoming KBytes RT Gauge This attribute counts the total number of Kbytes (1000 bytes) received on the interface, including those received in error, so far from the beginning of the current collection interval as indicated by time Interval. Mib name: acpmnetutilkbytestotalrx Number of Outgoing Pkts RT Gauge This attribute counts the Current total number of outgoing Packets from the interface, so far from the beginning of the current collection interval as indicated by time Interval. Mib name: acpmnetutilpacketstotaltx Number of Incoming Pkts RT Gauge This attribute counts the Current total number of Packets received on the interface, including those received in error, so far from the beginning of the current collection interval as indicated by time Interval. Mib name: acpmnetutilpacketstotalrx Number of Incoming Discarded Pkts RT Gauge This attribute counts the Current total number of malformed IP Packets received on the interface from the beginning of the current collection interval. These are packets which are corrupted or discarded due to errors in their IP headers, including bad checksums, version number mismatch, other format errors, time-tolive exceeded, errors discovered in processing their IP options, etc. Mib name: acpmnetutildiscardedpacketstotal Tab: VoP Call Statistics Frame: Gateway System Monitoring (Real-Time), Tab: VoP Call Statistics EMS Parameter Name RT / Hist Gauge / Counter Parameter Num of Active Contexts RT Gauge Indicates the current number of voice calls connected on the box since last clear. Mib name: acpmactivecontextcountval G711 Active Calls RT Gauge This attribute indicates the current number of G711 calls present on the TPM. Mib name: acpmchannelspercodervalg711 G723 Active Calls RT Gauge This attribute indicates the current number of G723 calls present on the TPM.This attribute is only displayed if the G723 Codec is provisioned on the DSP template. Mib name: acpmchannelspercodervalg723 G728 Active Calls RT Gauge This attribute indicates the current number of G728 calls present on the TPM.This attribute is only displayed if the G728 Codec is provisioned on the DSP template. Mib name: acpmchannelspercodervalg728 Version Performance Monitoring and Alarms

28 Mediant 1000B Gateway and E-SBC EMS Parameter Name RT / Hist Gauge / Counter Parameter G729a Active Calls RT Gauge This attribute indicates the current number of G729a calls present on the TPM.This attribute is only displayed if the G729a Codec is provisioned on the DSP. Mib name: acpmchannelspercodervalg729a G729e Active Calls RT Gauge This attribute indicates the current number of G729e calls present on the TPM.This attribute is only displayed if the G729e Codec is provisioned on the DSP template. Mib name: acpmchannelspercodervalg729e AMR Active Calls RT Gauge This attribute indicates the current number of AMR calls present on the TPM.This attribute is only displayed if the AMR Codec is provisioned on the DSP template. Mib name: acpmchannelspercodervalamr EVRC Active Calls RT Gauge This attribute indicates the current number of EVRC calls present on the TPM.This attribute is only displayed if the EVRC Codec is provisioned on the DSP template. Mib name: acpmchannelspercodervalevrc Rx Packet Loss current RT Gauge The total number of RTP packet loss reported by RTCP since last reset. Mib name: acpmmodulertppacketlossrxtotal Tx Packets Loss current RT Gauge The total number of RTP packet loss reported by RTCP since last reset. Mib name: acpmmodulertppacketlosstxtotal Rx Packets Current RT Gauge The total number of packets recieved since last reset. Mib name: acpmmodulertppacketsrxtotal Rx Packets Current RT Gauge The total number of RTP packets transmited since last reset. Mib name: acpmmodulertppacketstxtotal Tab: SIP IP to Tel Frame: Gateway System Monitoring (Real-Time), Tab: SIP IP to Tel EMS Parameter Name RT / Hist Gauge / Counter Parameter IP to Tel Number of Call Attempts IP to Tel Number of Established Calls IP to Tel Number of Calls Terminated due to a Busy Line RT RT RT Counter Indicates the number of attempted calls for IP to Tel direction, during last interval. Mib name: acpmsipattemptedcallsvalip2tel Counter Indicates the number of established calls for IP to Tel direction, during last interval. Mib name: acpmsipestablishedcallsvalip2tel Counter Indicates the number of calls that failed as a result of a busy line for IP to Tel direction, during last interval. Mib name: acpmsipbusycallsvalip2tel Performance Monitoring and Alarm Guide 28 Document #: LTRT-94954

29 Performance Monitoring and Alarm Guide 2. Performance Monitoring Parameters EMS Parameter Name RT / Hist Gauge / Counter Parameter IP to Tel Number of Calls Terminated due to No Answer IP to Tel Number of Calls Terminated due to Forward IP to Tel Number of Failed Calls due to No Route RT RT RT Counter Indicates the number of calls that weren't answered for IP to Tel direction, during last interval. Mib name: acpmsipnoanswercallsvalip2tel Counter Indicates the number of calls that were terminated due to a call forward for IP to Tel direction, during last interval. Mib name: acpmsipforwardedcallsvalip2tel Counter Indicates the number of calls whose destinations weren't found for IP to Tel direction, during last interval. Mib name: acpmsipnoroutecallsvalip2tel IP to Tel Number of Failed Calls due to No Matched Capabilities IP to Tel Number of Failed Calls due to No Resources IP to Tel Number of Failed Calls due to Other reasons IP to Tel Fax Call Attempts IP to Tel Successful Fax Calls IP to Tel Average Call Duration [sec] RT RT RT RT RT Counter Indicates the number of calls that failed due to mismatched media server capabilities for IP to Tel direction, during last interval. Mib name: acpmsipnomatchcallsvalip2tel Counter Indicates the number of calls that failed due to unavailable resources or a media server lock for IP to Tel direction, during last interval. Mib name: acpmsipnoresourcescallsvalip2tel Counter This counter is incremented as a result of calls that fail due to reasons not covered by the other counters for IP to Tel direction, during last interval. Mib name: acpmsipfailcallsvalip2tel Counter Indicates the number of attempted fax calls for IP to Tel direction, during last interval. Mib name: acpmsipfaxattemptedcallsvalip2tel Counter Indicates the number of successful fax calls for IP to Tel direction, during last interval. Mib name: acpmsipfaxsuccesscallsvalip2tel RT Gauge Indicates the average call duration of established calls for IP to Tel direction, during last interval. Mib name: acpmsipcalldurationaverageip2tel Version Performance Monitoring and Alarms

30 Mediant 1000B Gateway and E-SBC Tab: SIP Tel to IP Frame: Gateway System Monitoring (Real-Time), Tab: SIP Tel to IP EMS Parameter Name RT / Hist Gauge / Counter Parameter Tel to IP Number of Call Attempts Tel to IP Number of Established Calls Tel to IP Number of Calls Terminated due to a Busy Line Tel to IP Number of Calls Terminated due to No Answer Tel to IP Number of Calls Terminated due to Forward Tel to IP Number of Failed Calls due to No Route RT RT RT RT RT RT Counter Indicates the number of attempted calls for Tel to IP direction, during last interval. Mib name: acpmsipattemptedcallsvaltel2ip Counter Indicates the number of established calls for Tel to IP direction, during last interval. Mib name: acpmsipestablishedcallsvaltel2ip Counter Indicates the number of calls that failed as a result of a busy line for Tel to IP direction, during last interval. Mib name: acpmsipbusycallsvaltel2ip Counter Indicates the number of calls that weren't answered for Tel to IP direction, during last interval. Mib name: acpmsipnoanswercallsvaltel2ip Counter Indicates the number of calls that were terminated due to a call forward for Tel to IP direction, during last interval. Mib name: acpmsipforwardedcallsvaltel2ip Counter Indicates the number of calls whose destinations weren't found for Tel to IP direction, during last interval. Mib name: acpmsipnoroutecallsvaltel2ip Tel to IP Number of Failed Calls due to No Matched Capabilities Tel to IP Number of Failed Calls due to No Resources Tel to IP Number of Failed Calls due to Other reasons Tel to IP Fax Call Attempts Tel to IP Successful Fax Calls Tel to IP Average Call Duration [sec] RT RT RT RT RT Counter Indicates the number of calls that failed due to mismatched media server capabilities for Tel to IP direction, during last interval. Mib name: acpmsipnomatchcallsvaltel2ip Counter Indicates the number of calls that failed due to unavailable resources or a media server lock for Tel to IP direction, during last interval. Mib name: acpmsipnoresourcescallsvaltel2ip Counter This counter is incremented as a result of calls that fail due to reasons not covered by the other counters for Tel to IP direction, during last interval. Mib name: acpmsipfailcallsvaltel2ip Counter Indicates the number of attempted fax calls for Tel to IP direction, during last interval. Mib name: acpmsipfaxattemptedcallsvaltel2ip Counter Indicates the number of successful fax calls for Tel to IP direction, during last interval. Mib name: acpmsipfaxsuccesscallsvaltel2ip RT Gauge Indicates the average call duration of established calls for Tel to IP direction, during last interval. Mib name: acpmsipcalldurationaveragetel2ip Performance Monitoring and Alarm Guide 30 Document #: LTRT-94954

31 Performance Monitoring and Alarm Guide 2. Performance Monitoring Parameters 2.4 Frame: IP Group Monitoring (History) Tab: IP Group Statistics Frame: IP Group Monitoring (History), Tab: IP Group Statistics EMS Parameter Name RT / Hist Gauge / Counter Parameter SIP IP Group Dialogs Val Counter Value of gauge or counter. Mib name: acpmsipipgroupdialogsval SIP IP Group Invite Dialogs Val SIP IP Group Subscribe Dialogs Val SIP IP Group Other Dialogs Val SIP IP Group In Invite Dialogs SIP IP Group I nsubscribe Dialogs SIP IP Group Out Invite Dialogs SIP IP Group Out Subscribe Dialogs Counter Value of gauge or counter. Mib name: acpmsipipgroupinvitedialogsval Counter Value of gauge or counter. Mib name: acpmsipipgroupsubscribedialogsval Counter Value of gauge or counter. Mib name: acpmsipipgroupotherdialogsval Counter Value of gauge or counter. Mib name: acpmsipipgroupininvitedialogsval Counter Value of gauge or counter. Mib name: acpmsipipgroupinsubscribedialogsval Counter Value of gauge or counter. Mib name: acpmsipipgroupoutinvitedialogsval Counter Value of gauge or counter. Mib name: acpmsipipgroupoutsubscribedialogsval SIP IP Group Invite Dialogs IP Average SIP IP Group Invite Dialogs IP Max SIP IP Group Invite Dialogs IP Min Gauge Value of gauge or counter. Mib name: acpmsipipgroupinvitedialogsaverage Gauge Value of gauge or counter. Mib name: acpmsipipgroupinvitedialogsmax Gauge Value of gauge or counter. Mib name: acpmsipipgroupinvitedialogsmin Version Performance Monitoring and Alarms

32 Mediant 1000B Gateway and E-SBC 2.5 Frame: IP Group Monitoring (Real-Time) Tab: IP Group Statistics Frame: IP Group Monitoring (Real-Time), Tab: IP Group Statistics EMS Parameter Name RT / Hist Gauge / Counter Parameter SIP IP Group Dialogs Val RT Counter Value of gauge or counter. Mib name: acpmsipipgroupdialogsval SIP IP Group Invite Dialogs Val SIP IP Group Subscribe Dialogs Val SIP IP Group Other Dialogs Val SIP IP Group In Invite Dialogs SIP IP Group I nsubscribe Dialogs SIP IP Group Out Invite Dialogs SIP IP Group Out Subscribe Dialogs RT RT RT RT RT RT RT Counter Value of gauge or counter. Mib name: acpmsipipgroupinvitedialogsval Counter Value of gauge or counter. Mib name: acpmsipipgroupsubscribedialogsval Counter Value of gauge or counter. Mib name: acpmsipipgroupotherdialogsval Counter Value of gauge or counter. Mib name: acpmsipipgroupininvitedialogsval Counter Value of gauge or counter. Mib name: acpmsipipgroupinsubscribedialogsval Counter Value of gauge or counter. Mib name: acpmsipipgroupoutinvitedialogsval Counter Value of gauge or counter. Mib name: acpmsipipgroupoutsubscribedialogsval 2.6 Frame: SRD Monitoring (History) Tab: SRD Statistics Frame: SRD Monitoring (History), Tab: SRD Statistics EMS Parameter Name RT / Hist Gauge / Counter Parameter SIP SRD Dialogs Val Counter Value of gauge or counter. Mib name: acpmsipsrddialogsval SIP SRD Invite Dialogs Val Counter Value of gauge or counter. Mib name: acpmsipsrdinvitedialogsval SIP SRD Subscribe Dialogs Val SIP SRD Other Dialogs Val Counter Value of gauge or counter. Mib name: acpmsipsrdsubscribedialogsval Counter Value of gauge or counter. Mib name: acpmsipsrdotherdialogsval Performance Monitoring and Alarm Guide 32 Document #: LTRT-94954

33 Performance Monitoring and Alarm Guide 2. Performance Monitoring Parameters 2.7 Frame: SRD Monitoring (Real-Time) Tab: SRD Statistics Frame: SRD Monitoring (Real-Time), Tab: SRD Statistics EMS Parameter Name RT / Hist Gauge / Counter Parameter SIP SRD Dialogs Val RT Counter Value of gauge or counter. Mib name: acpmsipsrddialogsval SIP SRD Invite Dialogs Val SIP SRD Subscribe Dialogs Val SIP SRD Other Dialogs Val RT RT RT Counter Value of gauge or counter. Mib name: acpmsipsrdinvitedialogsval Counter Value of gauge or counter. Mib name: acpmsipsrdsubscribedialogsval Counter Value of gauge or counter. Mib name: acpmsipsrdotherdialogsval 2.8 Frame: System Monitoring SIP (Configuration) Tab: System IP Frame: System Monitoring SIP (Configuration), Tab: System IP EMS Parameter Name RT / Hist Gauge / Counter Parameter Number of Outgoing KBytes Number of Incoming KBytes Counter Counts the total number of outgoing Kbytes (1000 bytes) from the interface during the last interval. Mib name: acpmnetutilkbytesvolumetx Counter Counts the total number of Kbytes (1000 bytes) received on the interface, including those received in error, during the last interval. Mib name: acpmnetutilkbytesvolumerx Number of Outgoing Pkts Counter Counts the total number of outgoing Packets from the interface during the last interval. Mib name: acpmnetutilpacketsvolumetx Number of Incoming Pkts Counter Counts the total number of Packets received on the interface, including those received in error, during the last interval. Mib name: acpmnetutilpacketsvolumerx Version Performance Monitoring and Alarms

34 Mediant 1000B Gateway and E-SBC EMS Parameter Name RT / Hist Gauge / Counter Parameter Number of Incoming Discarded Pkts Counter Counts the total number of malformed IP Packets received on the interface during the last interval. These are packets which are corrupted or discarded due to errors in their IP headers, including bad checksums, version number mismatch, other format errors, time-tolive exceeded, errors discovered in processing their IP options, etc. Mib name: acpmnetutildiscardedpacketsval Tab: VoP Call Statistics Frame: System Monitoring SIP (Configuration), Tab: VoP Call Statistics EMS Parameter Name RT / Hist Gauge / Counter Parameter Num of Active Contexts Avg Num of Active Contexts Min Num of Active Contexts Max Gauge Indicates the average number of voice calls connected on the gateway since the last clear. Mib name: acpmactivecontextcountaverage Gauge Indicates the minimum number of voice calls connected on the gateway since the last clear. Mib name: acpmactivecontextcountmin Gauge Indicates the maximum number of voice calls connected on the gateway since the last clear. Mib name: acpmactivecontextcountmax G711 Active Calls Avg Gauge Indicates the average number of G.711 calls present on the TPM. Mib name: acpmchannelspercoderaverageg711 G723 Active Calls Avg Gauge Indicates the average number of G.723 calls present on the TPM. This attribute is only displayed if the G.723 Codec is provisioned on the DSP template. Mib name: acpmchannelspercoderaverageg723 G728 Active Calls Avg Gauge Indicates the average number of G.728 calls present on the TPM. This attribute is only displayed if the G.728 Codec is provisioned on the DSP template. Mib name: acpmchannelspercoderaverageg728 G729a Active Calls Avg Gauge Indicates the average number of G.729a calls present on the TPM. This attribute is only displayed if the G.729a Codec is provisioned on the DSP. Mib name: acpmchannelspercoderaverageg729a G729e Active Calls Avg Gauge Indicates the average number of G.729e calls present on the TPM. This attribute is only displayed if the G.729e Codec is provisioned on the DSP template. Mib name: acpmchannelspercoderaverageg729e AMR Active Calls Avg Gauge Indicates the average number of AMR calls present on the TPM. This attribute is only displayed if the AMR Codec is provisioned on the DSP template. Mib name: acpmchannelspercoderaverageamr Performance Monitoring and Alarm Guide 34 Document #: LTRT-94954

35 Performance Monitoring and Alarm Guide 2. Performance Monitoring Parameters EMS Parameter Name RT / Hist Gauge / Counter Parameter EVRC Active Calls Avg Gauge Indicates the average number of EVRC calls present on the TPM. This attribute is only displayed if the EVRC Codec is provisioned on the DSP template. Mib name: acpmchannelspercoderaverageevrc Rx RTP Packet Loss Max Tx RTP Packet Loss Max Gauge Indicates the Max Rx RTP Packet loss (reported by RTCP) per TPM, up to this point in time during the collection interval, as indicated by the time Interval. Mib name: acpmmodulertppacketlossrxmax Gauge Indicates the Max Tx RTP Packet loss (reported by RTCP) per TPM, up to this point in time during the collection interval, as indicated by the time Interval. Mib name: acpmmodulertppacketlosstxmax RTP delay Average Gauge Indicates the average RTP packets delay per TPM, up to this point in time during the collection interval, as indicated by the time Interval. Mib name: acpmmodulepacketdelayaverage RTP delay Max Gauge Indicates the maximum RTP packets delay per TPM, up to this point in time during the collection interval, as indicated by the time Interval. Mib name: acpmmodulepacketdelaymax RTP delay Min Gauge Indicates the minimum RTP packets delay per TPM, up to this point in time during the collection interval, as indicated by the time Interval. Mib name: acpmmodulepacketdelaymin RTP jitter Average Gauge Indicates the average RTP packets jitter per TPM, up to this point in time during the collection interval, as indicated by the time Interval. Mib name: acpmmodulepacketjitteraverage RTP jitter Min Gauge Indicates the minimum RTP packets jitter per TPM, up to this point in time during the collection interval, as indicated by the time Interval. Mib name: acpmmodulepacketjittermin RTP jitter Max Gauge Indicates the maximum RTP packets jitter per TPM, up to this point in time during the collection interval, as indicated by the time Interval. Mib name: acpmmodulepacketjittermax Rx RTP Bytes Max Gauge Indicates the Max Tx RTP Bytes per TPM, up to this point in time during the collection interval, as indicated by the time Interval. Mib name: acpmmodulertpbytesrxmax Tx RTP Bytes Max Gauge Indicates the Max Rx RTP Bytes per TPM, up to this point in time during the collection interval, as indicated by the time Interval. Mib name: acpmmodulertpbytestxmax Rx RTP Packets Max Gauge Indicates the Max Rx RTP Packets per TPM, up to this point in time during the collection interval, as indicated by the time Interval. Mib name: acpmmodulertppacketsrxmax Version Performance Monitoring and Alarms

36 Mediant 1000B Gateway and E-SBC EMS Parameter Name RT / Hist Gauge / Counter Parameter Tx RTP Packets Max Gauge Indicates the Max Tx RTP Packets per TPM, up to this point in time during the collection interval, as indicated by the time Interval. Mib name: acpmmodulertppacketstxmax RTCP XR Average Conversational R Factor RTCP XR Maximum Conversational R Factor RTCP XR Minimum Conversational R Factor Gauge Average conversational R factor. Mib name: rtcpxrhistoryavgrcq Gauge Maximum conversational R factor. Mib name: rtcpxrhistorymaxrcq Gauge Minimum conversational R factor. Mib name: rtcpxrhistoryminrcq Tab: SIP IP to Tel Frame: System Monitoring SIP (Configuration), Tab: SIP IP to Tel EMS Parameter Name RT / Hist Gauge / Counter Parameter IP to Tel Number of Call Attempts IP to Tel Number of Established Calls IP to Tel Number of Calls Terminated due to a Busy Line IP to Tel Number of Calls Terminated due to No Answer IP to Tel Number of Calls Terminated due to Forward IP to Tel Number of Failed Calls due to No Route IP to Tel Number of Failed Calls due to No Matched Capabilities Counter Indicates the number of attempted calls for IP to Tel direction, during last interval. Mib name: acpmsipattemptedcallsvalip2tel Counter Indicates the number of established calls for IP to Tel direction, during last interval. Mib name: acpmsipestablishedcallsvalip2tel Counter Indicates the number of calls that failed as a result of a busy line for IP to Tel direction, during last interval. Mib name: acpmsipbusycallsvalip2tel Counter Indicates the number of calls that weren't answered for IP to Tel direction, during last interval. Mib name: acpmsipnoanswercallsvalip2tel Counter Indicates the number of calls that were terminated due to a call forward for IP to Tel direction, during last interval. Mib name: acpmsipforwardedcallsvalip2tel Counter Indicates the number of calls whose destinations weren't found for IP to Tel direction, during last interval. Mib name: acpmsipnoroutecallsvalip2tel Counter Indicates the number of calls that failed due to mismatched media server capabilities for IP to Tel direction, during last interval. Mib name: acpmsipnomatchcallsvalip2tel Performance Monitoring and Alarm Guide 36 Document #: LTRT-94954

37 Performance Monitoring and Alarm Guide 2. Performance Monitoring Parameters EMS Parameter Name RT / Hist Gauge / Counter Parameter IP to Tel Number of Failed Calls due to No Resources IP to Tel Number of Failed Calls due to Other reasons IP to Tel Fax Call Attempts IP to Tel Successful Fax Calls IP to Tel Average Call Duration [sec] Counter Indicates the number of calls that failed due to unavailable resources or a media server lock for IP to Tel direction, during last interval. Mib name: acpmsipnoresourcescallsvalip2tel Counter This counter is incremented as a result of calls that fail due to reasons not covered by the other counters for IP to Tel direction, during last interval. Mib name: acpmsipfailcallsvalip2tel Counter Indicates the number of attempted fax calls for IP to Tel direction, during last interval. Mib name: acpmsipfaxattemptedcallsvalip2tel Counter Indicates the number of successful fax calls for IP to Tel direction, during last interval. Mib name: acpmsipfaxsuccesscallsvalip2tel Gauge Indicates the average call duration of established calls for IP to Tel direction, during last interval. Mib name: acpmsipcalldurationaverageip2tel Tab: SIP Tel to IP Frame: System Monitoring SIP (Configuration), Tab: SIP Tel to IP EMS Parameter Name RT / Hist Gauge / Counter Parameter Tel to IP Number of Call Attempts Tel to IP Number of Established Calls Tel to IP Number of Calls Terminated due to a Busy Line Tel to IP Number of Calls Terminated due to No Answer Tel to IP Number of Calls Terminated due to Forward Tel to IP Number of Failed Calls due to No Route Counter Indicates the number of attempted calls for Tel to IP direction, during last interval. Mib name: acpmsipattemptedcallsvaltel2ip Counter Indicates the number of established calls for Tel to IP direction, during last interval. Mib name: acpmsipestablishedcallsvaltel2ip Counter Indicates the number of calls that failed as a result of a busy line for Tel to IP direction, during last interval. Mib name: acpmsipbusycallsvaltel2ip Counter Indicates the number of calls that weren't answered for Tel to IP direction, during last interval. Mib name: acpmsipnoanswercallsvaltel2ip Counter Indicates the number of calls that were terminated due to a call forward for Tel to IP direction, during last interval. Mib name: acpmsipforwardedcallsvaltel2ip Counter Indicates the number of calls whose destinations weren't found for Tel to IP direction, during last interval. Mib name: acpmsipnoroutecallsvaltel2ip Version Performance Monitoring and Alarms

38 Mediant 1000B Gateway and E-SBC EMS Parameter Name RT / Hist Gauge / Counter Parameter Tel to IP Number of Failed Calls due to No Matched Capabilities Tel to IP Number of Failed Calls due to No Resources Tel to IP Number of Failed Calls due to Other reasons Tel to IP Fax Call Attempts Tel to IP Successful Fax Calls Tel to IP Average Call Duration [sec] Counter Indicates the number of calls that failed due to mismatched media server capabilities for Tel to IP direction, during last interval. Mib name: acpmsipnomatchcallsvaltel2ip Counter Indicates the number of calls that failed due to unavailable resources or a media server lock for Tel to IP direction, during last interval. Mib name: acpmsipnoresourcescallsvaltel2ip Counter This counter is incremented as a result of calls that fail due to reasons not covered by the other counters for Tel to IP direction, during last interval. Mib name: acpmsipfailcallsvaltel2ip Counter Indicates the number of attempted fax calls for Tel to IP direction, during last interval. Mib name: acpmsipfaxattemptedcallsvaltel2ip Counter Indicates the number of successful fax calls for Tel to IP direction, during last interval. Mib name: acpmsipfaxsuccesscallsvaltel2ip Gauge Indicates the average call duration of established calls for Tel to IP direction, during last interval. Mib name: acpmsipcalldurationaveragetel2ip Tab: SRD Statistics Frame: System Monitoring SIP (Configuration), Tab: SRD Statistics EMS Parameter Name RT / Hist Gauge / Counter Parameter SIP SRD Dialogs Val Counter Value of gauge or counter. Mib name: acpmsipsrddialogsval SIP SRD Invite Dialogs Val Counter Value of gauge or counter. Mib name: acpmsipsrdinvitedialogsval SIP SRD Subscribe Dialogs Val SIP SRD Other Dialogs Val Counter Value of gauge or counter. Mib name: acpmsipsrdsubscribedialogsval Counter Value of gauge or counter. Mib name: acpmsipsrdotherdialogsval Performance Monitoring and Alarm Guide 38 Document #: LTRT-94954

39 Performance Monitoring and Alarm Guide 2. Performance Monitoring Parameters Tab: IP Group Statistics Frame: System Monitoring SIP (Configuration), Tab: IP Group Statistics EMS Parameter Name RT / Hist Gauge / Counter Parameter SIP IP Group Dialogs Val Counter Value of gauge or counter. Mib name: acpmsipipgroupdialogsval SIP IP Group Invite Dialogs Val Counter Value of gauge or counter. Mib name: acpmsipipgroupinvitedialogsval SIP IP Group Subscribe Dialogs Val SIP IP Group Other Dialogs Val SIP IP Group In Invite Dialogs SIP IP Group I nsubscribe Dialogs SIP IP Group Out Invite Dialogs SIP IP Group Out Subscribe Dialogs Counter Value of gauge or counter. Mib name: acpmsipipgroupsubscribedialogsval Counter Value of gauge or counter. Mib name: acpmsipipgroupotherdialogsval Counter Value of gauge or counter. Mib name: acpmsipipgroupininvitedialogsval Counter Value of gauge or counter. Mib name: acpmsipipgroupinsubscribedialogsval Counter Value of gauge or counter. Mib name: acpmsipipgroupoutinvitedialogsval Counter Value of gauge or counter. Mib name: acpmsipipgroupoutsubscribedialogsval SIP IP Group Invite Dialogs IP Average SIP IP Group Invite Dialogs IP Max SIP IP Group Invite Dialogs IP Min Gauge Value of gauge or counter. Mib name: acpmsipipgroupinvitedialogsaverage Gauge Value of gauge or counter. Mib name: acpmsipipgroupinvitedialogsmax Gauge Value of gauge or counter. Mib name: acpmsipipgroupinvitedialogsmin Tab: Trunk Group Statistics Frame: System Monitoring SIP (Configuration), Tab: Trunk Group Statistics EMS Parameter Name RT / Hist Gauge / Counter Parameter Trunk Group Utilization (%) Trunk Group Utilization (channels) Gauge Value of gauge or counter. Mib name: acpmsiptrunkgrouppercentageutilizationval Gauge Value of gauge or counter. Mib name: acpmsiptrunkgrouputilizationval Tel to IP Trunk Group Established Calls Val Counter Value of gauge or counter. Mib name: acpmsiptel2iptrunkgroupestablishedcallsval Version Performance Monitoring and Alarms

40 Mediant 1000B Gateway and E-SBC EMS Parameter Name RT / Hist Gauge / Counter Parameter IP to Tel Trunk Group Established Calls Val Counter Value of gauge or counter. Mib name: acpmsipip2teltrunkgroupestablishedcallsval No Resources Calls Gauge Value of gauge or counter. Mib name: acpmsiptrunkgroupnoresourcescallsval Average Call Duration (sec) Gauge Value of gauge or counter. Mib name: acpmsiptrunkgroupcalldurationaverage Total Call Duration (sec) Gauge Value of gauge or counter. Mib name: acpmsiptrunkgroupcalldurationtotal Trunk Group All Trunks Busy (sec) Counter Value of gauge or counter. Mib name: acpmsiptrunkgroupalltrunksbusyval All Trunks Busy (%) Gauge Value of gauge or counter. Mib name: acpmsiptrunkgroupalltrunksbusypercentageval 2.9 Frame: Trunk Group Monitoring (History) Tab: Trunk Group Statistics Frame: Trunk Group Monitoring (History), Tab: Trunk Group Statistics EMS Parameter Name RT / Hist Gauge / Counter Parameter Trunk Group Utilization (%) Trunk Group Utilization (channels) Gauge Value of gauge or counter. Mib name: acpmsiptrunkgrouppercentageutilizationval Gauge Value of gauge or counter. Mib name: acpmsiptrunkgrouputilizationval Tel to IP Trunk Group Established Calls Val IP to Tel Trunk Group Established Calls Val Counter Value of gauge or counter. Mib name: acpmsiptel2iptrunkgroupestablishedcallsval Counter Value of gauge or counter. Mib name: acpmsipip2teltrunkgroupestablishedcallsval No Resources Calls Gauge Value of gauge or counter. Mib name: acpmsiptrunkgroupnoresourcescallsval Average Call Duration (sec) Gauge Value of gauge or counter. Mib name: acpmsiptrunkgroupcalldurationaverage Total Call Duration (sec) Gauge Value of gauge or counter. Mib name: acpmsiptrunkgroupcalldurationtotal Trunk Group All Trunks Busy (sec) Counter Value of gauge or counter. Mib name: acpmsiptrunkgroupalltrunksbusyval Performance Monitoring and Alarm Guide 40 Document #: LTRT-94954

41 Performance Monitoring and Alarm Guide 2. Performance Monitoring Parameters EMS Parameter Name RT / Hist Gauge / Counter Parameter All Trunks Busy (%) Gauge Value of gauge or counter. Mib name: acpmsiptrunkgroupalltrunksbusypercentageval 2.10 Frame: Trunk Group Monitoring (Real-Time) Tab: Trunk Group Statistics Frame: Trunk Group Monitoring (Real-Time), Tab: Trunk Group Statistics EMS Parameter Name RT / Hist Gauge / Counter Parameter Trunk Group Utilization (%) Trunk Group Utilization (channels) RT Gauge Value of gauge or counter. Mib name: acpmsiptrunkgrouppercentageutilizationval RT Gauge Value of gauge or counter. Mib name: acpmsiptrunkgrouputilizationval Tel to IP Trunk Group Established Calls Val IP to Tel Trunk Group Established Calls Val RT RT Counter Value of gauge or counter. Mib name: acpmsiptel2iptrunkgroupestablishedcallsval Counter Value of gauge or counter. Mib name: acpmsipip2teltrunkgroupestablishedcallsval No Resources Calls RT Gauge Value of gauge or counter. Mib name: acpmsiptrunkgroupnoresourcescallsval Average Call Duration (sec) RT Gauge Value of gauge or counter. Mib name: acpmsiptrunkgroupcalldurationaverage Total Call Duration (sec) RT Gauge Value of gauge or counter. Mib name: acpmsiptrunkgroupcalldurationtotal Trunk Group All Trunks Busy (sec) RT Counter Value of gauge or counter. Mib name: acpmsiptrunkgroupalltrunksbusyval All Trunks Busy (%) RT Gauge Value of gauge or counter. Mib name: acpmsiptrunkgroupalltrunksbusypercentageval Version Performance Monitoring and Alarms

42 Mediant 1000B Gateway and E-SBC 2.11 Frame: Trunk Monitoring (History) Tab: Trunk Performance Frame: Trunk Monitoring (History), Tab: Trunk Performance EMS Parameter Name RT / Hist Gauge / Counter Parameter Trunk utilization Avg Gauge Indicates the Average of simultaneously busy DS0 channels on this Trunk up to this point in time during the collection interval, as indicated by the Time Interval. A busy channel is when the Physical DS0 Termination isn't in Null context or OOS. A Trunk is either E1 or T1. Mib name: acpmtrunkutilizationaverage Trunk utilization Min Gauge Indicates the Minimum of simultaneously busy DS0 channels on this Trunk up to this point in time during the collection interval, as indicated by the Time Interval. A busy channel is when the Physical DS0 Termination isn't in Null context or OOS. A Trunk is either E1 or T1. Mib name: acpmtrunkutilizationmin Trunk utilization Max Gauge Indicates the Maximum of simultaneously busy DS0 channels on this Trunk up to this point in time during the collection interval, as indicated by the Time Interval. A busy channel is when the Physical DS0 Termination isn't in Null context or OOS. A Trunk is either E1 or T1. Mib name: acpmtrunkutilizationmax Trunk Errored Seconds Gauge Indicates the number of Errored Seconds. Mib name: dsx1intervaless Trunk Controlled Slip Seconds Gauge Indicates the number of Controlled Slip Seconds. Mib name: dsx1intervalcsss Trunk Path Coding Violations Trunk Bursty Errored Seconds Gauge Indicates the number of Path Coding Violations. Mib name: dsx1intervalpcvs Gauge Indicates the number of Bursty Errored Seconds. Mib name: dsx1intervalbess Performance Monitoring and Alarm Guide 42 Document #: LTRT-94954

43 Performance Monitoring and Alarm Guide 2. Performance Monitoring Parameters 2.12 Frame: Trunk Monitoring (Real-Time) Tab: Trunk Performance Frame: Trunk Monitoring (Real-Time), Tab: Trunk Performance EMS Parameter Name RT / Hist Gauge / Counter Parameter Trunk utilization RT Gauge This attribute indicates the Current simultaneous busy DS0 channels on this Trunk. A busy channel is when the Physical DS0 Termination isn't in Null context or OOS. A Trunk is either E1 or T1. Mib name: acpmtrunkutilizationval Trunk Calls Duration RT Gauge Value of gauge or counter. Mib name: acpmpstntrunkactivitysecondsval Trunk Errored Seconds RT Gauge This attribute indicates amount of Errored Seconds encountered by a DS1 interface in the previous 24 hour interval. Invalid 15 minute intervals count as 0. Mib name: dsx1totaless Trunk Controlled Slip Seconds Trunk Path Coding Violations Trunk Bursty Errored Seconds RT Gauge This attribute indicates amount of Controlled Slip Seconds encountered by a DS1 interface in the previous 24 hour interval. Invalid 15 minute intervals count as 0. Mib name: dsx1totalcsss RT Gauge This attribute indicates amount of Path Coding Violations encountered by a DS1 interface in the previous 24 hour interval. Invalid 15 minute intervals count as 0. Mib name: dsx1totalpcvs RT Gauge This attribute indicates amount of Bursty Errored Seconds encountered by a DS1 interface in the previous 24 hour interval. Invalid 15 minute intervals count as 0. Mib name: dsx1totalbess Version Performance Monitoring and Alarms

44 Mediant 1000B Gateway and E-SBC This page is intentionally left blank. Performance Monitoring and Alarm Guide 44 Document #: LTRT-94954

45 Performance Monitoring and Alarm Guide 3. Alarms 3 Alarms Supported alarms / events can fall into one of the following categories: Standard traps: traps originated by the media gateway / server - all the standard traps are treated are events. Proprietary alarms / events: traps originated by the media gateway / server and defined in the gateway proprietary MIB. EMS alarms / events: traps originated by the EMS application and defined in the EMS proprietary MIB. To find out which traps are defined as Events refer to 'Alarm Name' or '' fields in the table. All the events are marked with [Event] prefix. This is how events are marked in the EMS Alarms Browser and Alarms History windows. Each alarm / event described in this section includes the following information: Information Included in Each Alarm Alarm Name Severity Alarm Additional Info SNMP Trap Name SNMP Trap OID Corrective Action The alarm name, as it appears in the EMS Alarm Browser. Possible values of sources if applicable to a specific alarm. This value is displayed from the variable-binding tgtrapglobalssource. For the complete list of Managed Objects, refer to the Mediant 5000 / 8000 Programmers' User Manual. Possible values of severities. This value is displayed from the variablebinding tgtrapglobalsseverity. Alarm type according to ITU X.733 definition. This value is displayed from the variable-binding tgtrapglobalstype. Alarm probable cause according to ITU X.733 definition. This value is displayed from the variable-binding tgtrapglobalsprobablecause. Textual description of specific problem. This value is displayed from the variable-binding tgtrapglobalstextual. The document includes a few examples of the possible values of this field. Additional information fields provided by MG application, depending on the specific scenario. These values are displayed from tgtrapglobalsadditionalinfo1, tgtrapglobalsadditionalinfo2 and tgtrapglobalsadditionalinfo3. The document includes a few examples of the possible values of this field. NOTIFICATION-TYPE Name as it appears in the MIB. NOTIFICATION-TYPE OID as it appears in the MIB. Possible corrective action when applicable. Version Performance Monitoring and Alarms

46 Mediant 1000B Gateway and E-SBC 3.1 Standard Traps Cold Start Cold Start SNMPv2-MIB: A coldstart trap signifies that the SNMP entity, supporting a notification originator application, is reinitializing itself and that its configuration may have been altered. coldstart SNMP OID Severity Additional Info1,2,3 - Corrective Action - [Event] Cold Start Communication Alarm Other Clear Link Down This alarm is supported for Ethernet and DS1 links. Link Down SNMPv2-MIB: A linkdown trap signifies that the SNMP entity, acting in an agent role, has detected that the ifoperstatus object for one of its communication links is about to enter the down state from some other state (but not from the notpresent state). This other state is indicated by the included value of ifoperstatus. linkdown SNMP OID Severity Additional Info1,2,3 - Corrective Action - [Event] Link Down Communication Alarm Other Major Performance Monitoring and Alarm Guide 46 Document #: LTRT-94954

47 Performance Monitoring and Alarm Guide 3. Alarms Link Up This alarm is supported for Ethernet and DS1 links. Link Up SNMPv2-MIB: A linkup trap signifies that the SNMP entity, acting in an agent role, has detected that the ifoperstatus object for one of its communication links left the down state and transitioned into some other state (but not into the notpresent state). This other state is indicated by the included value of ifoperstatus. linkup SNMP OID Severity Additional Info1,2,3 Corrective Action [Event] Link Up Communication Alarm Other Clear Version Performance Monitoring and Alarms

48 Mediant 1000B Gateway and E-SBC Authentication Failure Authentication Failure SNMPv2-MIB: An authenticationfailure trap signifies that the SNMP entity has received a protocol message that is no properly authenticated. While all implementations of SNMP entities MAY be capable of generating this trap, the snmpenableauthentraps object indicates whether this trap will be generated. authenticationfailure SNMP OID Severity Additional Info1,2,3 Corrective Action [Event] Authentication Failure Communication Alarm Other Major Performance Monitoring and Alarm Guide 48 Document #: LTRT-94954

49 Performance Monitoring and Alarm Guide 3. Alarms DS1 Line Status DS1 Line Status From RFC 3895 (Definitions of Managed Objects for the DS1, E1, DS2, and E2 Interface Types. O. Nicklass, Ed.. September 2004): A dsx1linestatuschange trap is sent when the value of an instance dsx1linestatus changes. It can be utilized by an NMS to trigger polls. When the line status change results from a higher level line status change (i.e., ds3), then no traps for the ds1 are sent. dsx1linestatuschange SNMP OID Severity Additional Info1,2,3 [Event] DS1 Line Status Communication Alarm Trunk# (number of trunk) Other Major on raise, Clear on clear Updated DS1 Line Status. This variable indicates the Line Status of the interface. It contains loopback, failure, received 'alarm' and transmitted 'alarms' information. The dsx1linestatus is a bit map represented as a sum, therefore, it can represent multiple failures (alarms) and a LoopbackState simultaneously. dsx1noalarm must be set if and only if no other flag is set. If the dsx1loopbackstate bit is set, the loopback in effect can be determined from the dsx1loopbackconfig object. The various bit positions are: 1 dsx1noalarm No alarm present 2 dsx1rcvfarendlof Far end LOF (a.k.a., Yellow Alarm) 4 dsx1xmtfarendlof Near end sending LOF Indication 8 dsx1rcvais Far end sending AIS 16 dsx1xmtais Near end sending AIS 32 dsx1lossofframe Near end LOF (a.k.a., Red Alarm) 64 dsx1lossofsignal Near end Loss Of Signal 128 dsx1loopbackstate Near end is looped 256 dsx1t16ais E1 TS16 AIS 512 dsx1rcvfarendlomf Far End Sending TS16 LOMF 1024 dsx1xmtfarendlomf Near End Sending TS16 LOMF 2048 dsx1rcvtestcode Near End detects a test code 4096 dsx1otherfailure Any line status not defined here 8192 dsx1unavailsigstate Near End in Unavailable Signal State dsx1netequipoos Carrier Equipment Out of Service dsx1rcvpayloadais DS2 Payload AIS dsx1ds2perfthreshold DS2 Performance Threshold Exceeded Corrective Action - Version Performance Monitoring and Alarms

50 Mediant 1000B Gateway and E-SBC 3.2 EMS Alarms EMS Trap Receiver Binding Error EMS Trap Receiver Binding Error Textual This alarm is generated during server startup if an error occurs indicating that the SNMP trap receiver port is already taken. SNMP OID acemssnmpcannotbinderror AlarmTitle ItuAlarmType AlarmSource Severity [Event] EMS Trap Receiver Binding Error Environmental Alarm EMS Server Application Subsystem Failure Critical Additional Info - Corrective Action Media Gateways Run netstats command to verify which application uses the alarms reception port (by default UDP post 162). EMS application: If it's busy, check which application uses this port. If it's not freed by the EMS application, restart the EMS Server application according to the equipment installation manual. Other network management application: change the EMS application and all managed gateways' default alarm reception ports. All the gateways managed by the EMS Performance Monitoring and Alarm Guide 50 Document #: LTRT-94954

51 Performance Monitoring and Alarm Guide 3. Alarms GW Connection Alarm GW Connection Alarm Textual Originated by the EMS when an SNMP Timeout occurs for the first time in the Media Gateway. SNMP OID acemsnodeconnectionlostalarm AlarmTitle ItuAlarmType AlarmSource Severity GW Connection Alarm Communications Alarm Media Gateway Communications Subsystem Failure Critical Additional Info - Corrective Action Media Gateways Communication problem: Try to ping the gateway to check if there is network communication. Default gateway alive: Open the network screen. Check the default gateway IP address and ping it. SNMP Community Strings: Verify that the community string defined in the EMS for the gateway matchs the actual gateway community strings. To check the community string, right-click on the gateway, select the 'Details' menu. Default community strings: read = public, write = private. Hardware Problem: Check that the gateway is alive according to the LEDs. Verify that network and power cables are in place and plugged in. All the gateways managed by the EMS GW Mismatch Alarm GW Mismatch Alarm Textual Activated when the EMS detects a hardware, software, predefine or configuration mismatch. Software Mismatch: Activated when the EMS detects a software version mismatch between the actual and the previous definition of the Media Gateway (for example, Version instead of the previously defined ). This is also the case when the new version is not defined in the Software Manager. Hardware Mismatch: Activated when the EMS detects a hardware mismatch between the actual and the previous definition of a Media Gateway. Configuration Mismatch: Activated when the EMS detects a configuration mismatch between the actual parameter values provisioned and previous parameter values provisioned. SNMP OID acemsnomismatchnodealarm Version Performance Monitoring and Alarms

52 Mediant 1000B Gateway and E-SBC AlarmTitle ItuAlarmType AlarmSource GW Mismatch Alarm Equipment Alarm Media Gateway/Software Media Gateway/Hardware Media Gateway/Configuration Severity Other Clear Additional Info - Corrective Action Media Gateways Software Mismatch: Define the detected version in the EMS Software Manager Perform a Software Upgrade on the gateway with one of the supported versions. Hardware Mismatch: Perform remove / add a gateway from the EMS tree in order to resync EMS and the gateway status Verify in the Software Manager that an appropriate version exists for the hardware type displayed in the error message Configuration Mismatch: Run Configuration Verification command in order to compare EMS configuration and actual MG configuration: -MG configuration is incorrect: use configuration download to update MG with correct configuration saved in the EMS database. -MG is correct, EMS is not updated: use configuration upload to save a correct MG configuration in the EMS database. Check the Actions Journal for recent updates of the gateway. All the gateways managed by the EMS. Performance Monitoring and Alarm Guide 52 Document #: LTRT-94954

53 Performance Monitoring and Alarm Guide 3. Alarms EMS Server Started Textual EMS Server Started Originated each time the server is started or restarted (warm boot/reboot) by the EMS Watchdog Process SNMP OID acemsserverstartup AlarmTitle ItuAlarmType AlarmSource Severity Additional Info - Corrective Action - Media Gateways [Event] EMS Server Started Communications Alarm EMS Server Other Major All the gateways managed by the EMS Disk Space Alarm Textual Disk Space Alarm Originated when the EMS Server hard disk capacity is almost full. SNMP OID acemsnotenoughdiskspacealarm AlarmTitle ItuAlarmType AlarmSource - Disk Space Alarm Environment Alarm EMS Server Severity Critical - disk usage > 80 % Major - disk usage > 70 % Additional Info - Corrective Action Clean all unnecessary files Expand the hard disk Media Gateways All the gateways managed by the EMS. Version Performance Monitoring and Alarms

54 Mediant 1000B Gateway and E-SBC Software Replaced Software Replaced Textual Originates when the EMS discovers a software version replace between board versions, for example, from V to V (when both versions are managed by the EMS). Software Replace old version : <old version> new version <new version> SNMP OID acemssoftwarereplacealarm AlarmTitle ItuAlarmType AlarmSource Severity Additional Info Corrective Action Media Gateways [Event] Software Replaced Communications Alarm EMS Server Other Info If you initiated a performance measurements polling process before you initiated the software replacement process, the polling process is stopped. No action should be taken; this is an information alarm. All the gateways managed by the EMS Hardware Replaced Hardware Replaced Textual Originated when the EMS discovers a different gateway (according to the MAC address) to what was initially defined, while the Hardware Type remains the same. Hardware Replace is discovered by the MAC address and performed during Board Started trap. SNMP OID acemshardwarereplacealarm AlarmTitle ItuAlarmType AlarmSource Severity [Event] Hardware Replaced Equipment Alarm Media Gateway Other Major Additional Info - Corrective Action - Media Gateways MediaPacks, Mediant 1000, Mediant 2000, Mediant 3000 Performance Monitoring and Alarm Guide 54 Document #: LTRT-94954

55 Performance Monitoring and Alarm Guide 3. Alarms HTTP/HTTPS Access Disabled HTTP/HTTPS Access Disabled Textual Originated when HTTP access is disabled by EMS hardening but the EMS manages media gateways that require HTTP access for software upgrade. Originated on server startup. SNMP OID acemshttpdisabled AlarmTitle ItuAlarmType AlarmSource Severity [Event] HTTP/HTTPS Access Disabled Environmental Alarm EMS Server Application Subsystem Failure Major Additional Info - Corrective Action Media Gateways Separate the gateways between two EMS Servers (secured & unsecured) Gateways using the HTTP server for the software upgrade procedure: MediaPacks, Mediant 1000, Mediant 2000, Mediant PM File Generated PM File Generated Textual Originated when a PM file is generated in the EMS server, and it can be retrieved by a higher level management system. SNMP OID acemspmfilegenerate AlarmTitle ItuAlarmType AlarmSource Severity Additional Info [Event] PM File Generated Other EMS Server Other Info The performance summary data from<start polling interval time> to<timestempfileto> of media gateway<nodeipadd> was saved in PM file <filename>. Corrective Action - Media Gateways All Gateways Version Performance Monitoring and Alarms

56 Mediant 1000B Gateway and E-SBC PM Polling Error PM Polling Error Textual Originated when a PM History stops collecting performance summary data from MG. Possible reasons are: NTP synchronization lost, Connection Loss, SW Mismatch, etc.. SNMP OID acemspmhistoryalarm AlarmTitle ItuAlarmType AlarmSource Severity [Event] PM Polling Error Other EMS Server Other Minor Additional Info Corrective Action Media Gateways Verify in the 'Textual ' (see above) the reason why the PM history stopped. When the reason is 'NTP synchronization lost', verify that the gateway and the EMS Server machine are synchronized to the same NTP server and have accurate time definitions. When the reason is 'Software Mismatch', you can stop the PM history collection until the new version is added to the Software Manager. When the reason is 'Connection Loss' between the EMS Server and the gateway, polling continues automatically when the connection is re-established; the purpose of the alarm in this case is to inform users of missing samples. Note: The alarm continues to activate every 15 minutes unless you fix the problem or manually stop PM polling of the Gateway. All Gateways Performance Monitoring and Alarm Guide 56 Document #: LTRT-94954

57 Performance Monitoring and Alarm Guide 3. Alarms Cold Start Missed Textual Cold Start Missed Originated when Carrier Grade Alarm System recognizes coldstart trap has been missed. SNMP OID acemsnodecoldstartmissedevent AlarmTitle ItuAlarmType AlarmSource Severity Additional Info Corrective Action Media Gateways [Event] Cold Start Missed Other Receive failure Clear All the managed Gateways Security Alarm Textual Security Alarm Activated when one of more Radius servers are not reachable. When none of the radius servers can be reached, a Critical Severity alarm is generated. SNMP OID acemssecurityalarm AlarmTitle ItuAlarmType Security Alarm Processing Error Alarm AlarmSource EMS Server / Radius <#> Severity Additional Info Corrective Action Media Gateways Other Minor, Major, Critical Version Performance Monitoring and Alarms

58 Mediant 1000B Gateway and E-SBC Security Event Security Event Textual This event is generated when a specific user is blocked after reaching the maximum number of login attempts, or when the EMS failed to sync EMS and Mediant 5000 / 8000 users. SNMP OID acemssecurityevent AlarmTitle ItuAlarmType AlarmSource Severity [Event] Security Event Other EMS Server / User Name, EMS Sever / User Sync Other Indeterminate Additional Info Corrective Action Media Gateways Topology Update Event Topology Update Event Textual This event is issued by the EMS when a Gateway or Region is added/removed/updated in the EMS application and includes the following information: Action: Add / Remove / Update GW or Region Region Name GW Name GW IP Note: For opening an EMS client in the MG context, the gateway IP address should be provided. SNMP OID acemstopologyupdateevent Severity [Event] Topology Update EMS Server Indeterminate Other Other Performance Monitoring and Alarm Guide 58 Document #: LTRT-94954

59 Performance Monitoring and Alarm Guide 3. Alarms Additional Info Additional Info 1 field will include following details: Region: X1 'X2' [GW: Y1 'Y2' 'Y3' 'Y4'] X1 = Region ID (unique identifier in the EMS data base used for region identification) X2 = Region name as it defined by EMS operator Y1 = GW ID (unique identifier in the EMS data base used for GW identification) Y2 = GW Name as it defined by EMS operator Y3 = GW IP as it defined by EMS operator Y4 = GW Type as it identified by EMS during the first connection to the GW. If first connection was not successful during the add operation, it will trigger an 'Add GW' event with Unknown GW type, and 'Update GW' event once the initial connection to the GW has been successfull. The following GWs will be supported: MP,M1K, M2K, M3K, M5K, M8K Region details will always be part of the alarm, while GW info will be displayed when event is GW related. All the fields related to the GW will always be displayed to allow easy parsing. Examples: (=Add Region) Region: 7 'Test Lab' (=Update Region) Region: 7 'My Updated Region' (=Add GW) Region: 7 'My Updated Region', GW: 22 'MG14' ' ' 'Unknown', PM Polling: disabled (=Update GW) Region: 7 'My Updated Region', GW: 22 'My MG 15' ' ' 'M3K' (=Update GW) Region: 7 'My Updated Region', GW: 22 'My MG 15' ' ', PM Polling: enabled (=Remove GW) Region: 7 'My Updated Region', GW: 22 'My MG 15' ' ' 'M3K', Polling: enabled (=Remove Region) Region: 7 'My Updated Region' Corrective Action Media Gateways Version Performance Monitoring and Alarms

60 Mediant 1000B Gateway and E-SBC Topology File Event Textual Topology File Event This event is issued by the EMS when the Topology File is updated on the EMS Server machine.the Topology file is automatically updated upon the addition /removal of a Media Gateway or upon updates to the Media Gateway properties. For more information, refer to the OAMP Integration Guide. SNMP OID acemstopologyfileevent [Event] Topology File Severity Additional Info Corrective Action Media Gateways Indeterminate Other Other File Name: MGsTopologyList.csv Synchronizing Alarms Event Textual Synchronizing Alarms Event This event is issued when the EMS is not able to retrieve the entire missing alarms list from the History table. Information regarding the number of retrieved alarms, and number of alarms EMS failed to retrieve is provided in the Additional Info field. SNMP OID acemssyncalarmevent Severity Additional Info Corrective Action Media Gateways [Event] Synchronizing Alarms EMS Server Indeterminate Other Other Retrieved x missed alarms, failed to retrieve y alarms. Performance Monitoring and Alarm Guide 60 Document #: LTRT-94954

61 Performance Monitoring and Alarm Guide 3. Alarms Synchronizing Active Alarms Event Synchronizing Active Alarms Event Textual This event is issued when the EMS is not able to perform synchronization with the History alarms table, and instead performs synchronization with the Active Alarms Table. SNMP OID acemssyncactivealarmevent [Event] Synchronizing Active Alarms Severity Indeterminate Other Other Additional Info Corrective Action Media Gateways License Key Alarm License Key Alarm Textual This alarm is raised when one of the following occurs: EMS Application License is expired. EMS Application License will be expired within one month. Gateway management is not covered by the current EMS Application License (the maximum number of EMS licenses for managing this gateway has been exceeded). SNMP OID acemslicensekeyalarm EMS License Key Alarm Severity Major/Critical Other keyexpired Additional Info Corrective Action Media Gateways Version Performance Monitoring and Alarms

62 Mediant 1000B Gateway and E-SBC Alarm Supression Alarm Alarm Suppression Alarm This alarm is sent when the EMS suppresses alarms (of the same alarm type and alarm source), once the number of such alarms reaches a configured threshold level in a configured interval (configured in the EMS in the Alarms Settings screen). When this alarm is sent, such alarms are not added to the EMS database and are not forwarded to configured destinations. AlarmSuppressionAlarm SNMP OID Default Severity Alarm Text Status Changes Additional Info Corrective Action Indeterminate Other Threshold crossed. Alarm Suppression activated The alarm is cleared when in the subsequent interval, the number of such alarms falls below the configured threshold. Once the alarm is cleared, then these alarms are once more added to the EMS database and forwarded to configured destinations. Investigate the recurrence of such alarms EMS Keep Alive Alarm EMS Keep-Alive Alarm This alarm indicates that an SNMP Keep-alive trap has been sent from EMS to a third-party destination such as a Syslog server to indicate EMS liveness (configured in the EMS Alarms Settings window). EMSKeepAliveAlarm SNMP OID Default Severity Indeterminate Other Other Alarm Text EMS Server Keep-Alive Status Changes Additional Info Corrective Action Performance Monitoring and Alarm Guide 62 Document #: LTRT-94954

63 Performance Monitoring and Alarm Guide 3. Alarms Pre-provisioning Alarm Pre-provisioning Alarm SNMP OID This alarm is generated when the operation for pre-provisioning the device upon initial connection to the EMS fails. AlarmTitle AlarmType AlarmSource Severity Pre-Provisioning operational/violation EMS server The template file could not be applied to the device because there was a mismatch between the template file and the device s existing ini file or there was a mismatch between the device type and the firmware file applied to the device. Critical Additional Info - Corrective Action When this alarm is raised, you cannot reload configuration or firmware files to the device as it has already been connected to the EMS. Instead download these files to the device using the Software Manager and then use the 'Software Upgrade' action. OR Remove the device from the EMS and then reconnect it i.e. repeat the pre-provisioning process. Media Gateways All gateways managed by EMS. Version Performance Monitoring and Alarms

64 Mediant 1000B Gateway and E-SBC 3.3 SEM Alarms SEM Failed Calls Alarm SEM Failed Calls Alarm This alarm is raised when the failed calls threshold is crossed and is cleared when the failed calls ratio returns below the threshold value. The description field includes the info: Failed X1% of calls, X2 of X3 calls. acsemrulefailedcallsalarm SNMP OID alarm type Severity Additional Info Corrective Action SEM - Failed Calls Alarm SEM/<Device Name> or SEM/<Link Name> (According to provisioned scope) Quality of service alarm. The minimum or maximum threshold is crossed. According to provisioned thresholds: critical, major or clear Critical or Major severity threshold is Y%: Critical Threshold: 5% of calls (default) Major Threshold: 3% of calls (default Investigate the source (device or link) of the failed calls SEM Voice Quality Alarm SEM Voice Quality Alarm This alarm is raised when the poor quality calls threshold is crossed and is cleared when the poor quality calls ratio returns below the threshold value. The description field includes the info: Poor Quality X1% of calls, X2 of X3 calls. acsemrulepoorqualitycallsalarm SNMP OID Severity Additional Info Corrective Action SEM Voice Quality Alarm SEM/<Device Name> or SEM/<Link Name> (According to provisioned scope) Quality of service alarm. The minimum or maximum threshold is crossed. According to provisioned thresholds: critical, major or clear Critical or Major severity threshold is Y%: Critical Threshold: 10% of calls (default). Major Threshold: 8% of calls (default); Investigate the source (device or link) of the poor quality calls. Performance Monitoring and Alarm Guide 64 Document #: LTRT-94954

65 Performance Monitoring and Alarm Guide 3. Alarms SEM Average Call Duration Alarm SEM Average Call Duration Alarm This alarm is raised when the average call duration time threshold is crossed and is cleared when the average call duration time ratio returns below the threshold value. The description field includes the info: Average Call Duration is X sec. acsemruleavrgcalldurationalarm SNMP OID Severity Additional Info Corrective Action SEM Average Call Duration Alarm SEM/<Device Name> or SEM/<Link Name> (According to provisioned scope) Quality of service alarm. The minimum or maximum threshold is crossed. According to provisioned thresholds: critical, major or clear Critical or Major severity threshold is Y sec. Investigate the source (device or link) reporting the excessive average call duration SEM License Key Alarm SEM License Key Alarm This alarm is sent when the SEM application License Key file is invalid. Gateway management is not covered by the current SEM Application License. acsemlicensekeyalarm SNMP OID Severity Corrective Action SEM License key alarm. SEM server Other Key Expired Critical Contact your AudioCodes representitve to obtain a correct license key. Version Performance Monitoring and Alarms

66 Mediant 1000B Gateway and E-SBC SEM System Load Alarm SEM System Load Alarm This alarm is sent when the SEM system capacity is high and the system consequently becomes loaded. Three levels are supported: Minor - > Events are not stored for green calls. Trend Info will not be displayed. Major -> Events are not stored. Trend Info will not be displayed. Critical -> Green calls are not stored. acsemcalldroppedalarm SNMP OID SEM System Load Alarm SEM Server Quality of service alarm. AlarmProbableCauseType.THRESHOLDCROSSED Severity MINOR/ MAJOR/ CRITICAL Additional Info Medium load level is reached - {0}%, {1} calls of {2}. / High load level is reached - {0}%, {1} calls of {2}. / Approaching maximal system capacity - {0}%, {1} calls of {2}. Corrective Action Reduce the system load SEM Call Details Storage Level has Changed SEM Call Details Storage Level has Changed This alarm is sent when the operator changes the Call Details Storage Level from one level to another. acsemclientloadflagalarm SNMP OID Severity SEM Call Details Storage Level has been changed. SEM Server Quality of service alarm Threshold crossed. Indeterminate Additional Info Corrective Action Performance Monitoring and Alarm Guide 66 Document #: LTRT-94954

67 Performance Monitoring and Alarm Guide 3. Alarms SEM Time Synchronization Alarm SEM Time Synchronization Alarm This alarm is sent when Device and Server are not synchronized: Server Time: {0}, Device Time: {1}. acsemtimesynchronizationalarm SNMP OID Severity SEM Time Synchronization Alarm SEM/<Device Name> or SEM/<Link Name> (According to provisioned scope) Timedomainviolational Timing Problem Critical One of the following reasons will appear: Additional Info Corrective Action Check your NTP configuration on the device. NTP servers are not configured on the device. Ensure that the SEM server and device time is properly synchronized. Verify that the NTP configuration is correct; verify your network conditions (Firewalls, Ports, etc..) and make sure that the NTP sync of the SEM server and/or the devices is performed correctly. Refer to the EMS client / Help menu / EMS Server Configuration frame to verify the network configuration. See above SEM AD Lync Connection Alarm This alarm is sent when there is no connectivity with the Lync SQL Server database. acmslyncconnectionalarm SNMP OID Severity Additional Info Corrective Action SEM AD Lync Connection Alarm Lync SQL Server Communications alarm Communications sub-system failure Critical Check the Lync SQL server for problems. Version Performance Monitoring and Alarms

68 Mediant 1000B Gateway and E-SBC SEM MS Lync AD Server Alarm This alarm is sent when there is no connectivity with the Active Directory LDAP server. acsemmslyncadserveralarm SNMP OID Severity Additional Info Corrective Action SEM MS Lync AD Server Alarm Active Directory LDAP server Communications alarm Communications sub-system failure Critical SEM - AD Lync connection alarm Check the MS Lync AD server for problems SEM Rule Bandwidth Alarm This alarm is sent when the media bandwidth for the node or link falls below or exceeds the threshold values configured in the SEM Quality Alerts window. acsemrulebandwidthalarm SNMP OID Default Severity Alarm Text Status Changes Additional Info Corrective Action SEM Rule Bandwidth Alarm According to provisioned thresholds: critical, major or clear. Quality of service alarm Threshold crossed Maximum Bandwidth of X Kb/sec Check the node's or link's maximum bandwidth capacity matches the required capacity. Performance Monitoring and Alarm Guide 68 Document #: LTRT-94954

69 Performance Monitoring and Alarm Guide 3. Alarms SEM Rule Max Concurrent Calls Alarm This alarm is sent when the maximum concurrent calls for the node or link falls below or exceeds the threshold values configured in SEM Quality Alerts window. acsemrulemaxconcurrentcallsalarm SNMP OID Default Severity Alarm Text Status Changes Additional Info Corrective Action According to provisioned thresholds: critical, major or clear Quality of service alarm Threshold crossed. Max Concurrent Calls of X Check that the node's or link's maximum number of concurrent calls matches the required capacity. Version Performance Monitoring and Alarms

70 Mediant 1000B Gateway and E-SBC 3.4 IP Phone Alarms Registration Failure Alarm IP Phone Registration Failure Alarm This alarm is raised when a SIP registration (with a PBX) for the IP Phone fails. IPPhoneRegisterFailure OID Severity Corrective Action Registration Failure IP Phone communicationsalarm(1) communicationsprotocolerror(5) Critical The problem is typically not related to the phone, but to the server. The user/phone may not be defined, or may be incorrectly defined, or may previously have been defined but the username (for example) may have been changed, causing the registration to fail. Make sure the username and password credentials are identical in the server and phone, and weren't changed; server-phone credentials must be synchronized. Make sure the server is responsive Lync Survivable Mode Start Alarm IP Phone Survivable Mode Start Alarm This alarm is raised when the IP Phone enters Survivable mode state with limited services in the Microsoft Lync environment. IPPhoneSurvivableModeStart OID Survivable Mode Start IP Phone Other(0) other (0) Severity Corrective Action Major The problem is typically not related to the phone, but to the server or network. Make sure all servers in the enterprise's network are up. If one is down, limited service will result. Performance Monitoring and Alarm Guide 70 Document #: LTRT-94954

71 Performance Monitoring and Alarm Guide 3. Alarms Lync Login Failure Alarm IP Phone Lync Login Failure Alarm This alarm is raised when the IP Phone fails to connect to Microsoft Lync Server during sign in. IPPhoneLyncLoginFailure OID Severity Additional Info Corrective Action Lync Login Failure IP Phone communicationsalarm(1) communicationsprotocolerror(5) Critical TlsConnectionFailure NtpServerError This alarm may typically occur if the user is not registered - or is registered incorrectly - in the Lync Server. Make sure that username, password and PIN code are correctly configured and valid in the Lync Server. Try resetting them. Try redefining the user. Version Performance Monitoring and Alarms

72 Mediant 1000B Gateway and E-SBC 3.5 Device Alarms Board Fatal Error Board Fatal Error Sent whenever a fatal device error occurs. acboardfatalerror SNMP OID Board Fatal Error equipmentalarm underlyingresourceunavailable (56) Alarm Severity Condition <text> Corrective Action Critical (default) Stays 'Critical' until reboot. A 'Clear' trap is not sent. Any fatal error Board Fatal Error: A run-time specific string describing the fatal error After fatal error - 1. Capture the alarm information and the Syslog clause, if active. 2. Contact AudioCodes' Support Center at support@audiocodes.com which will want to collect additional data from the device and perform a reset. Performance Monitoring and Alarm Guide 72 Document #: LTRT-94954

73 Performance Monitoring and Alarm Guide 3. Alarms Configuration Error Configuration Error Sent when the device's settings are invalid. The trap contains a message stating/detailing/explaining the invalid setting. acboardconfigurationerror SNMP OID AlarmType Probable Cause [Event] Configuration Error equipmentalarm underlyingresourceunavailable (56) Alarm Severity Condition <text> Corrective Action Critical (default) Stays 'Critical' until reboot. A 'Clear' trap is not sent. A configuration error was detected After configuration error Board Config Error: A run-time specific string describing the configuration error - 1. Check the run-time specific string to determine the nature of the configuration error. 2. Fix the configuration error using the appropriate tool: Web interface, EMS, or ini file. 3. Save the configuration and if necessary reset the device. Version Performance Monitoring and Alarms

74 Mediant 1000B Gateway and E-SBC Temperature Alarm Temperature Alarm Sent when the device exceeds its temperature limits. acboardtemperaturealarm SNMP OID Temperature Alarm equipmentalarm System#0 The air filter is saturated. One of the fans work slower than expected. temperatureunacceptable (50) Alarm Severity Condition <text> Corrective Action Critical Cleared Internal temperature is too high for normal operation Temperature returns to normal operating values Board temperature too high - - Check that the ambient environment around the chassis was not changed (room temperature, air-conditioner, and location of the chassis on the site). If the ambient environment is the same, make sure that all unoccupied module slots are covered with blank panels. Check the chassis ventilation outlet and make sure that they are not obstructed for air flow. Check if you also received a Fan Tray alarm, which indicates that one or more fans in the Fan Tray are faulty (major). If this is the case, send the faulty Fan Tray to AudioCodes as RMA. Send an RMA request to AudioCodes for the Fan Tray. Performance Monitoring and Alarm Guide 74 Document #: LTRT-94954

75 Performance Monitoring and Alarm Guide 3. Alarms Initialization Ended Initialization Ended This alarm is sent when the device is initialized and ready to run. acboardevboardstarted SNMP OID [Event] Initialization Ended Equipment Alarm Other Severity Major Additional Info1,2,3 NULL Board Resetting Following Software Reset Board Resetting Following Software Reset This alarm indicates that the device has started the reset process - following a software reset. acboardevresettingboard SNMP OID Severity Additional Info1,2,3 Corrective Action Board Resetting Following Software Reset Other Other Critical 'AdditionalInfo1', 'AdditionalInfo2', 'AdditionalInfo3', A network administrator has taken action to reset the device. No corrective action is needed. Version Performance Monitoring and Alarms

76 Mediant 1000B Gateway and E-SBC Feature Key Related Error Feature Key Related Error Sent to relay Feature Key errors etc. acfeaturekeyerror SNMP OID Severity Feature Key Related Error Critical processingerroralarm configurationorcustomizationerror (7) Alarm Text Note Feature key error Support for this alarm is pending. Performance Monitoring and Alarm Guide 76 Document #: LTRT-94954

77 Performance Monitoring and Alarm Guide 3. Alarms Gateway Administrative State Changed Gateway Administrative State Changed This alarm indicates that the administrative state of the gateway has been changed to a new state. Note that all state changes are instigated by the parameter acgwadminstate. Time limit set in the parameter acgwadminstatelockcontrol - 'GateWay shutting down. Max time to LOCK %d sec' No time limit in the parameter acgwadminstatelockcontrol - 'GateWay is shutting down. No time limit.' When reaching lock state - 'GateWay is locked' When the gateway is SET to unlocked - 'GateWay is unlocked (fully active again)' acgwadminstatechange SNMP OID Administrative State Change Equipment Alarm Other Severity Major Major Major Cleared Additional Info1,2,3 Corrective Action NULL A network administrator has taken an action to lock the device. No corrective action is required. Version Performance Monitoring and Alarms

78 Mediant 1000B Gateway and E-SBC No Free Channels Available No Free Channels Available This alarm indicates that almost no free resources for the call are available. Activated only if the parameter EnableRai is set. The threshold is determined according to parameters RAIHIGHTHRESHOLD and RAILOWTHRESHOLD. acboardcallresourcesalarm SNMP OID AlarmType No Free Channels Available processingerroralarm 'GWAPP' softwareerror (46) Alarm Severity Condition <text> Corrective Action Major (default) Percentage of busy channels exceeds the predefined RAI high threshold Call resources alarm Expand system capacity by adding more channels (trunks) -OR- Reduce traffic Cleared Percentage of busy channels falls below the predefined RAI low threshold - Note that to enable this alarm, the Remote Alarm Indication (RAI) mechanism must be activated (EnableRAI = 1). Performance Monitoring and Alarm Guide 78 Document #: LTRT-94954

79 Performance Monitoring and Alarm Guide 3. Alarms Gatekeeper/Proxy not Found or Registration Failed Proxy not Found or Registration Failed The alarm is sent in the following scenarios: Physical FXO port is up or down (Out-of-Service or OOS). The FXO line can be down due to, for example, port disconnected or insufficient current and voltage. (Syslog message event is ANALOG_IF_LINE_DISCONNECTED.) Physical BRI or PRI (E1/T1) port is up or down (OOS). Proxy is not found or registration fails. In such a case, the device's routing table may be used for routing instead of the Proxy. Connection to the Proxy is up or down. Failure in TDM-over-IP call - transparent E1/T1 without signalling. Connection to the Proxy Set associated with the trunk/line is up/down. Failure in server registration for the trunk/line. Failure in a Serving IP Group for the trunk. Failure in a Proxy Set. acboardcontrollerfailurealarm SNMP OID 'GWAPP' Proxy not Found or Registration Failed processingerroralarm softwareerror (46) Alarm Severity Condition Text Additional Information Major (default) FXO physical port is down "BusyOut Line n Link failure" Where n represents the FXO port number (0 for the first port). Verify that the FXO line is securely cabled to the device's FXO port. BRI or PRI physical port is down "BusyOut Trunk n Link failure" Where n represents the BRI or PRI port number (0 for the first port). Verify that the digital trunk is securely cabled to the device's digital port. Proxy has not been found or registration failure "Proxy not found. Use internal routing" -OR- "Proxy lost. Looking for another Proxy" Check the network layer Make sure that the proxy IP and port are configured correctly. Connection to Proxy is down "BusyOut Trunk/Line n Connectivity Proxy failure" - Version Performance Monitoring and Alarms

80 Mediant 1000B Gateway and E-SBC Connection to the Proxy Set associated with the trunk or line is down "BusyOut Trunk/Line n Proxy Set Failure" Where n represents the BRI/ PRI trunk or FXO line. - Failure in a Proxy Set Failure in TDMover-IP call Failure in server registration for the trunk/line Failure in a Serving IP Group for the trunk "Proxy Set ID n" Where n represents the Proxy Set ID. "BusyOut Trunk n TDM over IP failure (Active calls x Min y)" Where n represents the BRI/ PRI trunk. "BusyOut Trunk/Line n Registration Failure" Where n represents the BRI/ PRI trunk or FXO line. "BusyOut Trunk n Serving IP Group Failure" Where n represents the BRI or PRI trunk ID Cleared Proxy is found. The 'Cleared' message includes the IP address of this Proxy. - - Performance Monitoring and Alarm Guide 80 Document #: LTRT-94954

81 Performance Monitoring and Alarm Guide 3. Alarms Ethernet Link Down Alarm Ethernet Link Down Alarm This alarm indicates that the Ethernet link is down or remote Ethernet link is down and the board has no communication to any other host. No link at all. Link is up again. Primary link is down only - 'Primary Link is lost. Switching to Secondary Link' acboardethernetlinkalarm SNMP OID Ethernet Link Down Alarm All except Mediant 3000: Board#<n>/EthernetLink#0 (where n is the slot number) Mediant 3000: Chassis#0/Module#<n>/EthernetLink#0 (where n is the blade's slot number) This trap relates to the Ethernet Link Module (the #0 numbering doesn't apply to the physical Ethernet link). equipmentalarm underlyingresourceunavailable (56) Alarm Severity Condition <text> Corrective Action Major Critical (default) Fault on single interface Fault on both interfaces Ethernet link alarm: Redundant link is down No Ethernet link 1. Ensure that both Ethernet cables are plugged into the back of the system. 2. Observe the system s Ethernet link lights to determine which interface is failing. 3. Reconnect the cable or fix the network problem Cleared Both interfaces are operational -. Version Performance Monitoring and Alarms

82 Mediant 1000B Gateway and E-SBC System Component Overloaded System Component Overloaded This alarm is raised when there is an overload in one or more of the system's components. acboardoverloadalarm SNMP OID Severity Major processingerroralarm 'GWAPP' softwareerror (46) Alarm Severity Condition <text> Corrective Action Major (default) An overload condition exists in one or more of the system components "System CPU overload condition - IdleUtilization percentage=%d Where %d is the percentage of available CPU resources remaining 1. Make sure that the syslog level is 0 (or not high). 2. Make sure that DebugRecording is not running. 3. If the system is configured correctly, reduce traffic. Cleared The overload condition passed System CPU overload condition - IdleUtilization percentage=% - Performance Monitoring and Alarm Guide 82 Document #: LTRT-94954

83 Performance Monitoring and Alarm Guide 3. Alarms Active Alarms Table Overflow Active Alarms Table Overflow This alarm is raised when there are too many alarms to fit into the active alarm table. The status stays major until reboot as it denotes a possible loss of information until the next reboot. If an alarm was raised when the table was full, it is possible that the alarm is active, but does not appear in the active alarm table. acactivealarmtableoverflow SNMP OID [Event] Active Alarm Table Overflow Processing Error Alarm MG resourceatornearingcapacity (43) Severity Additional Info1,2,3 - Corrective Action Major Some alarm information may have been lost, but the ability of the device to perform its basic operations has not been impacted. A reboot is the only way to completely clear a problem with the active alarm table. Contact your first-level group. Version Performance Monitoring and Alarms

84 Mediant 1000B Gateway and E-SBC Operational State Change Operational State Change This alarm is raised if the operational state of the node is disabled. The alarm is cleared when the operational state of the node is enabled. acoperationalstatechange SNMP OID Operational State Change processingerroralarm outofservice (71) Alarm Severity Condition <text> Corrective Action Major (default) Cleared Operational state changed to disabled Operational state changed to enabled Network element operational state change alarm. Operational state is disabled. - - The alarm is cleared when the operational state of the node goes to enabled. In IP systems, check for initialization errors - in IP systems the operational state of the node is disabled if the device fails to properly initialize. Look for other alarms and Syslogs that might provide additional information about the error. Performance Monitoring and Alarm Guide 84 Document #: LTRT-94954

85 Performance Monitoring and Alarm Guide 3. Alarms Keep Alive Trap Keep Alive Trap Part of the NAT traversal mechanism. If the STUN application in the device detects a NAT, this trap is sent on a regular time laps - 9/10 of the acsysstunbindinglifetime object. The AdditionalInfo1 varbind has the MAC address of the device. ackeepalive SNMP OID [Event] Keep Alive Trap other (0) other (0) Severity Event Text Indeterminate Keep alive trap Status Changes Condition Trap Status Note The STUN client is enabled and identified as a NAT device or doesn t locate the STUN server. The ini file contains the following line SendKeepAliveTrap=1 Trap is sent Keep-alive is sent every 9/10 of the time defined in the parameter NatBindingDefaultTimeout. Version Performance Monitoring and Alarms

86 Mediant 1000B Gateway and E-SBC NAT Traversal Alarm NAT Traversal Alarm This alarm is sent when the NAT is placed in front of a device and is identified as a symmetric NAT. It is cleared when a non-symmetric NAT or no NAT replace the symmetric one. acnattraversalalarm SNMP OID other (0) NAT Traversal Alarm MG other (0) Severity Additional Info1,2,3 - Status Changes Indeterminate The STUN client in the device is enabled and has either identified a NAT or is not finding the STUN server. Keep-alive is sent out every 9/10 of the time defined in the 'NatBindingDefaultTimeout' parameter. Corrective Action See Performance Monitoring and Alarm Guide 86 Document #: LTRT-94954

87 Performance Monitoring and Alarm Guide 3. Alarms Threshold of Performance Monitored Object Exceeded Threshold of Performance Monitored Object Exceeded Sent every time the threshold of a Performance Monitored object (counter or gauge) ('Minimum', 'Average', 'Maximum', 'Distribution below/above/between thresholds', and 'Low and high thresholds') is crossed. The severity field is 'Indeterminate' when the crossing is above the threshold and 'Cleared' when it goes back under the threshold. The 'Source' varbind in the trap indicates the object for which the threshold is being crossed. acperformancemonitoringthresholdcrossing SNMP OID Severity Additional Info1,2,3 - Corrective Action - Threshold of Performance Monitored Object Exceeded Other MO Path Other Indeterminate (this is a notification; it's not automatically cleared) Version Performance Monitoring and Alarms

88 Mediant 1000B Gateway and E-SBC HTTP Download Result HTTP Download Result This is a log message (not alarm) indicating both sucessful and failed HTTP Download result. achttpdownloadresult SNMP OID Severity Additional Info Corrective Action - [Event] HTTP Download Result processingerroralarm (3) for failures and other (0) for success Other Indeterminate There are other possible textual messages describing NFS failures or success, FTP failure or success. Performance Monitoring and Alarm Guide 88 Document #: LTRT-94954

89 Performance Monitoring and Alarm Guide 3. Alarms Fan Tray Alarm Fan Tray Alarm This alarm is activated in one of the following cases: Fan-Tray is missing One or more fans in the fan-tray is faulty. Fan tray is in place and fans are functioning. acfantrayalarm SNMP OID Alarm Text Fan Tray Alarm Chassis#0/FanTray#0 Fan-Tray Alarm <text> equipmentalarm One or more fans on the Fan Tray module stopped working. One or more fans on the Fan Tray module works slower than expected (heatingventcoolingsystemproblem) Alarm Severity Condition <text> Corrective Action Critical Fan-Tray is missing. Fan-Tray is missing 1. Check if the Fan Tray module is inserted in the chassis. 2. If the Fan Tray module was removed from the chassis, reinsert it. 3. If the Fan Tray module has already been inserted in the chassis and the alarm is active, send a Return Merchandise Authorization (RMA) request to AudioCodes. Warning: When removing the Fan Tray module while the power is on (or after it has recently been switched off), the blades may still be rotating at high speeds. Therefore, to avoid bodily harm, make sure that you don't touch the fan blades. Major When one or more fans in the Fan Tray are faulty. Fan-Tray is faulty Fan Tray module is faulty. Send a Return Merchandise Authorization (RMA) request to AudioCodes. Cleared Fan Tray module is in place and fans are working. - - Version Performance Monitoring and Alarms

90 Mediant 1000B Gateway and E-SBC Power Supply Alarm Power Supply Alarm This alarm is activated in one of the following cases: The HA (High Availability) feature is active and one of the power supply units is faulty or missing. PS unit is inserted in its location and functioning. acpowersupplyalarm SNMP OID Chassis#0/PowerSupply#<m>, where m is the power supply s slot number equipmentalarm powerproblem Alarm Severity Condition <text> Corrective Action Major (default) The HA (High Availability) feature is active (applicable only to Mediant 3000) and one of the power supply units is faulty or missing. Power-Supply Alarm. Power-Supply is missing. 1. Check if the unit is inserted in the chassis. 2. If it was removed from the chassis, re-insert it. 3. If it's inserted in the chassis and the alarm is active, send a Return Merchandise Authorization (RMA) request to AudioCodes. Cleared PS unit is placed and working. - - Note To enable the sending of this SNMP trap, set the ini file parameter, Mediant1000DualPowerSupplySupported to 2. Performance Monitoring and Alarm Guide 90 Document #: LTRT-94954

91 Performance Monitoring and Alarm Guide 3. Alarms D-Channel Status This alarm applies to digital media gateways. D-Channel Status Non-alarm trap sent at the establishment, re-establishment or release of LAPD link with its peer connection occurs. The trap is sent with one of the following textual descriptions: D-channel synchronized D-channel not-synchronized acdchannelstatus SNMP OID Severity Additional Info - Corrective Action - D-Channel Status Trunk no.<m> where m is the trunk number (from 0 up). Communications Alarm Communications Protocol Error Minor on raise, Clear on clear Version Performance Monitoring and Alarms

92 Mediant 1000B Gateway and E-SBC Dial Plan File Replaced Trap This alarm applies to the Analog Series and Mediant Digital Series. Dial Plan File Replaced This event informs that the dial plan file has been successfully replaced. acdialplanfilereplaced SNMP OID Dial Plan File Replaced Default Severity Indeterminate Event Type Other (0) Other (0) Status Change Condition Successful dial plan file replacement Trap Text Dial plan file replacement complete. Performance Monitoring and Alarm Guide 92 Document #: LTRT-94954

93 Performance Monitoring and Alarm Guide 3. Alarms Analog Port SPI Out of Service This alarm applies to analog ports running SIP control protocol. Analog Port SPI Out of Service This alarm indicates that the analog port is out of service. acanalogportspioutofservice SNMP OID Analog Port SPI Out of Service System#0/analogports#<n>, where n is the port number physicalviolation equipmentmalfunction Alarm Severity Condition <text> Corrective Action Major (default) Cleared Analog port has gone out of service Analog port is back in service Analog Port SPI out of service - - No corrective action is required. The device shuts down the port and activates it again when the Serial Peripheral Interface (SPI) connection returns. Version Performance Monitoring and Alarms

94 Mediant 1000B Gateway and E-SBC Analog Port High Temperature This alarm applies to analog ports (only FXS ports) running the SIP control protocol. Analog Port High Temperature This alarm indicates that the analog FXS port has a high temperature. acanalogporthightemperature SNMP OID Analog Port High Temperature System#0/analogports#<n>, where n is the port number physicalviolation equipmentmalfunction Alarm Severity Condition <text> Corrective Action Major (default) Cleared Analog device has reached critical temperature. Device is automatically disconnected. Temperature is back to normal - analog port is back in service. Analog Port High Temperature - - No corrective action is required. The device shuts down the analog port and tries to activate it again later when the device's temperature drops. Performance Monitoring and Alarm Guide 94 Document #: LTRT-94954

95 Performance Monitoring and Alarm Guide 3. Alarms Trunk LOS Alarm This alarm applies to E1/T1Trunks. Trunk LOS Alarm This alarm indicates a loss of signal at the trunk's near end. actrunksalarmnearendlos SNMP OID Trunk LOS Alarm Interfaces#0/Trunk#<m>, where m is the trunk interface number, 1 being the first trunk communicationsalarm lossofsignal Alarm Severity Condition <text> Corrective Action Critical (default) Near-end LOS Trunk LOS Alarm Los of Signal (LOS) indicates a physical problem. 4. Check that the cable is connected on the board. 5. Check that the correct cable type is being used (crossed/straight). 6. Contact AudioCodes' Support Center at support@audiocodes.com. Cleared End of LOS - - Version Performance Monitoring and Alarms

96 Mediant 1000B Gateway and E-SBC Trunk LOF Alarm This alarm applies to E1/T1Trunks. Trunk LOF Alarm This alarm indicates a loss of frame at the trunk's near end. actrunksalarmnearendlof SNMP OID Trunk LOF Alarm Interfaces#0/Trunk#<m>, where m is the trunk interface number, 1 being the first trunk communicationsalarm lossofframe Alarm Severity Condition <text> Corrective Action Critical (default) Near end LOF Trunk LOF Alarm Make sure that the trunk is connected to a proper follow-up device. 7. Make sure that both sides are configured with the same (E1 / T1) link type. 8. Make sure that both sides are configured with the same framing method. 9. Make sure that both sides are configured with the same line code. 10. Make sure that the clocking setup is correct. 11. Contact AudioCodes' Support Center at support@audiocodes.com. Cleared End of LOF - - Performance Monitoring and Alarm Guide 96 Document #: LTRT-94954

97 Performance Monitoring and Alarm Guide 3. Alarms Trunk AIS Alarm This alarm applies to E1/T1Trunks. Trunk AIS Alarm This alarm indicates that an AIS is received from the trunk's far end. actrunksalarmrcvais SNMP OID Interfaces#0/Trunk#<m>, where m is the trunk interface number, 1 being the first trunk Trunk AIS Alarm communicationsalarm PSTN provider has stopped the trunk (receivefailure) Alarm Severity Condition <text> Corrective Action Critical Receive AIS Trunk AIS Alarm 1. Contact your PSTN provider to activate the trunk. 2. If the alarm persists, contact the AudioCodes Support Center at support@audiocodes.co m Cleared End of AIS - - Version Performance Monitoring and Alarms

98 Mediant 1000B Gateway and E-SBC Trunk RAI Alarm This alarm to E1/T1Trunks. Trunk RAI Alarm This alarm indicates a loss of frame at the trunk's far end. actrunksalarmfarendlof SNMP OID Severity Trunk RAI Alarm Port#<n> where n is the digital trunk number communicationsalarm transmitfailure Critical Additional Info Corrective Action Check trunk's connectivity Performance Monitoring and Alarm Guide 98 Document #: LTRT-94954

99 Performance Monitoring and Alarm Guide 3. Alarms IPv6 This alarm indicates when an IPv6 address already exists or an IPv6 configuration failure has occurred. The description generated is "IP interface alarm. IPv6 Configuration failed, IPv6 will be disabled". acipv6erroralarm SNMP OID Default Severity Critical System#0/Interfaces#<n>. operationalviolation communicationsprotocolerror Additional Info Status stays critical until reboot. A clear trap is not sent. Corrective Action Find a new IPV6 address and reboot. Alarm Severity Condition <text> Corrective Action Critical (default) Bad IPv6 address (already exists) IP interface alarm: IPv6 configuration failed, IPv6 will be disabled. Find a new IPV6 address. Reboot the device. Stays 'Critical' until reboot. A 'Clear' trap is not sent. After the alarm is raised. - - Version Performance Monitoring and Alarms

100 Mediant 1000B Gateway and E-SBC SAS Emergency Mode Alarm This alarm applies to SIP Gateways. GW SAS Emergency Mode Alarm This alarm is sent by the Stand-Alone Survivability (SAS) application when switching from Normal" mode to Emergency" mode. This alarm is cleared once the SAS returns to Normal" mode. acgwsasemergencymodealarm SNMP OID GW SAS Emergency Mode Alarm Other Other Severity Additional Info Corrective Action Check network communication with the Proxy Performance Monitoring and Alarm Guide 100 Document #: LTRT-94954

101 Performance Monitoring and Alarm Guide 3. Alarms NTP Server Status Alarm NTP Server Status Alarm This alarm is raised when the connection to the NTP server is lost. It is cleared when the connection is reestablished. Unset time (as a result of no connection to NTP server) may result in functionality degradation and failure in device. acntpserverstatusalarm SNMP OID NTP Server Status Alarm communicationsalarm communicationssubsystemfailure Alarm Severity Condition <text> Corrective Action Major (default) No initial communication to Network Time Protocol (NTP) server. NTP server alarm. No connection to NTP server. Repair NTP communication (the NTP server is down or its IP address is configured incorrectly in the device). Minor No communication to NTP server after the time was already set once. - - Version Performance Monitoring and Alarms

102 Mediant 1000B Gateway and E-SBC LDAP Lost Connection LDAP Lost Connection This alarm is raised when there is no connection to the LDAP server. acldaplostconnection SNMP OID LDAP Lost Connection Severity communicationsalarm communicationssubsystemfailure If a connection is idle for more than the maximum configured time in seconds that the client can be idle before the LDAP server closes the connection, the LDAP server returns an LDAP disconnect notification and this alarm is raised. Minor / Clear Additional Info Corrective Action Performance Monitoring and Alarm Guide 102 Document #: LTRT-94954

103 Performance Monitoring and Alarm Guide 3. Alarms Analog Port Ground Fault Out of Service This alarm is relevant for devices with FXS ports only. Analog Port Ground Fault Out of Service This alarm is raised when the FXS port is inactive due to a ground fault. acanalogportgroundfaultoutofservice SNMP OID Severity Additional Information Analog Port Ground Fault Out Of Service physicalviolation equipmentmalfunction (this alarm is raised when the FXS port is inactive due to a ground fault). Major / Clear Corrective Action No corrective action is required. The device shuts down the port and tries to activate it again when the relevant alarm is over. Version Performance Monitoring and Alarms

104 Mediant 1000B Gateway and E-SBC SSH Connection Status [Event] SSH Connection Status [Event] This trap indicates the result of a recent SSH connection attempt. acsshconnectionstatus SNMP OID SSH Connection Status "SSH logout from IP address <IP>, user <user>" "SSH successful login from IP address <IP>, user <user> at: <IP>:<port>" "SSH unsuccessful login attempt from IP address <IP>, user <user> at: <IP>:<port>. <reason>" "WEB: Unsuccessful login attempt from <IP> at <IP>:<port>. <reason>" environmentalalarm unauthorizedaccessattempt/other Alarm Text Severity indeterminate Additional Info Corrective Action OCSP Server Status Alarm OCSP Server Status Alarm This alarm is raised when the OCSP connection is not available. acocspserverstatusalarm SNMP OID OCSP server alarm. Severity communicationsalarm communicationssubsystemfailure Major / Clear Additional Information Corrective Action Repair the Online Certificate Status Protocol (OCSP) server -OR- Correct the network configuration Performance Monitoring and Alarm Guide 104 Document #: LTRT-94954

105 Performance Monitoring and Alarm Guide 3. Alarms Power over Ethernet Status [Event] Power over Ethernet Status [Event] This event is sent when Power over Ethernet (PoE) for a specific port is disabled. acpoweroverethernetstatus SNMP OID Event Text [Event] Power over Ethernet Status underlyingresourceunavailable POE Port %d Was Not Powered Due To Power Management where %d is the Ethernet port number Default Severity Condition Indeterminate This trap is sent when insufficient power is available for a plugged-in PoE client in a PoE-enabled LAN port. Additional Info Corrective Action Media Process Overload Alarm Media Process Overload Alarm This alarm is raised when the media process overloads and is cleared when the load returns to normal. acmediaprocessoverloadalarm SNMP OID Media Process Overload Alarm Board#x or System#x environmentalalarm resourceatornearingcapacity Alarm Severity Condition <text> Corrective Action Major (default) - Media Process Overload Alarm. %s Cleared - - None Avoid making new calls. Although not corrective, this action eventually causes the alarm to drop. Version Performance Monitoring and Alarms

106 Mediant 1000B Gateway and E-SBC Wireless Cellular Modem Alarm Wireless Cellular Modem Alarm This alarm is raised when either the wireless modem is down or in backup mode and is cleared when the wireless modem is up. acwirelesscellularmodemalarm SNMP OID Default Severity Source Varbind Text Wireless Cellular Modem Alarm Major / Clear Board#x/WanLink#y equipmentalarm underlyingresourceunavailable Alarm Severity Condition <text> Corrective Action Major Raised when either the wireless modem is down or in backup mode, and cleared when modem is up. WAN wireless cellular modem alarm Get the link up. Investigate the possibility of an electronics failure or a problem with the radio frequency (RF) path. Clear WAN link up - - Performance Monitoring and Alarm Guide 106 Document #: LTRT-94954

107 Performance Monitoring and Alarm Guide 3. Alarms NFAS Group Alarm NFAS Group Alarm This alarm is raised when an NFAS group goes Out-Of-Service and is cleared when an NFAS Group is back In-Service. acnfasgroupalarm SNMP OID Interfaces#0/Trunk#<m>, where m is the trunk interface number, 1 being the first trunk communicationsalarm degradedsignal Alarm Severity Condition <text> Corrective Action Major (default) Raised when an NFAS group goes out-ofservice NFAS Group Alarm. %s The alarm is sent only when the backup Non- Facility Associated Signaling (NFAS) D- channel also falls, i.e., when both D-channels are down. When at least one of the D-channels (primary or backup) returns to service, the alarm is cleared. Corrective action is not necessary. Clear NFAS group state goes to in- service %s Additional information - Version Performance Monitoring and Alarms

108 Mediant 1000B Gateway and E-SBC B Channel Alarm B Channel Alarm This alarm is raised when the B-Channel service state changes and is cleared when the B-Channel is back in service. acbchannelalarm SNMP OID Default Severity Source Varbind Text AlarmType B-Channel Alarm. Interface#%d/trunk#%d/BChannel#%d Minor Interfaces#0/Trunk#<m>, where m is the trunk interface number, 1 being the first trunk communicationsalarm degradedsignal Alarm Severity Condition <text> Corrective Action Major Raised when B- channel service state changes to 'Out of Service' or 'Maintenance' B-Channel Alarm. %s Corrective action is not necessary Clear B-channel status changes to 'In Service' %s additional information - Performance Monitoring and Alarm Guide 108 Document #: LTRT-94954

109 Performance Monitoring and Alarm Guide 3. Alarms Ethernet Group Alarm Ethernet Group Alarm This alarm is raised when the in an Ethernet port-pair group (1+1) has no Ethernet port with its link up and is cleared when at least one port has established a link. acethernetgroupalarm SNMP OID Severity Additional Info Corrective Action Ethernet Group alarm. Board#%d/EthernetGroup#%d equipmentalarm underlyingresourceunavailable major Media Realm BW Threshold Alarm Media Realm BW Threshold Alarm This alarm is raised when a BW threshold is crossed and is cleared when the BW threshold returns to normal range. acmediarealmbwthresholdalarm SNMP OID Severity Additional Info Corrective Action Media Realm BW Threshold Alarm. Board#%d/MediaRealm#%d processingerroralarm resourceatornearingcapacity major Version Performance Monitoring and Alarms

110 Mediant 1000B Gateway and E-SBC Certificate Expiry Notification Certificate Expiry Notification This alarm is sent before the expiration of the installed credentials, which cannot be renewed automatically (the credentials should be updated manually). accertificateexpirynotification SNMP OID Certificate Expiry Notification tls#<num> Alarm Text Device s TLS certificate of security context #%d will expire in %d days environmentalalarm The certificate key expired (keyexpired) Alarm Severity Condition <text> Corrective Action Intermediate The certificate key is about to expire. Either: The device certificate has expired %d days ago The device certificate will expire in %d days The device certificate will expire in less than 1 day %d number of days %d TLS Context to which certificate belongs Load a new certificate to the device before the expiration of the installed certificate (which cannot be renewed automatically). To replace certificates, refer to the User's Manual. Performance Monitoring and Alarm Guide 110 Document #: LTRT-94954

111 Performance Monitoring and Alarm Guide 3. Alarms Web User Access Disabled WEB User Access Disabled This alarm is sent when the Web user has been disabled due to inactivity. acwebuseraccessdisabled SNMP OID Severity other The Web user was disabled due to inactivity (denialofservice). indeterminate Additional Info Corrective Action Contact your Web security administrator. Only the Web security administrator can unblock a user whose access to the Web interface was denied (for example, because the user made 3 unsuccessful attempts at access). The Web security administrator must: In the Web interface, access the Accounts page (Configuration > System > Management > Web User Accounts). Identify in the list of users table that user whose access has been denied. Change the status of that user from Blocked to Valid or New. Version Performance Monitoring and Alarms

112 Mediant 1000B Gateway and E-SBC Proxy Connection Lost Proxy Connection Lost This alarm is sent when all connections in a specific Proxy Set are down. The trap is cleared when one of the Proxy Set connections is up. acproxyconnectionlost SNMP OID Proxy Connection Lost Alarm Text System#0 Proxy Set Alarm <text> communicationsalarm Network issue (connection fail due to network/routing failure). Proxy issue (proxy is down). AudioCodes device issue. Alarm Severity Condition <text> Corrective Action Major When connection to the Proxy Set is lost and this Proxy Set is configured with fallback to routing table. Proxy Set %d: Proxy not found. Use internal routing 1. Ping the proxy server. If there is no ping, contact your proxy provider. The probable reason is the proxy is down. 2. Ping between the proxy and AudioCodes device. If there is no ping, the problem could be a network/router issue. 3. If you have more than one device connected to this same proxy, check if there are more AudioCodes devices with the same Alarm. If this is the case, this could confirm that this is not AudioCodes device issue. 4. Check that routing using the device's (internal) routing table is functioning correctly. 5. Contact AudioCodes support center (support@audiocodes.com) and send a syslog and network capture for this issue. Performance Monitoring and Alarm Guide 112 Document #: LTRT-94954

113 Performance Monitoring and Alarm Guide 3. Alarms Major Cleared When Proxy Set includes more than one proxy IP with redundancy and connection to one of them is lost. When connection to proxy is available again Proxy Set %d: Proxy lost. looking for another proxy Proxy found. ip:<ip address>:<port #> Proxy Set ID %d 1. Ping the proxy server. If there is no ping, contact your proxy provider. The probable reason is the proxy is down. 2. Ping between the proxy and AudioCodes device. If there is no ping, the problem could be a network/router issue. 3. If you have more than one device connected to this same proxy, check if there are more AudioCodes devices with the same Alarm. If this is the case, this could confirm that this is not AudioCodes device issue. 4. Check if routing via the redundant proxy is operating correctly. If it is, then this could mean that it's not a network issue. 5. Contact AudioCodes support center (support@audiocodes.com) and send a syslog and network capture for this issue Redundant Board Alarm Redundant Board Alarm The active board sends a notification when an alarm or notification is raised on the redundant board. acredundantboardalarm SNMP OID Redundant Board Alarm Notification Severity Additional Info Corrective Action Version Performance Monitoring and Alarms

114 Mediant 1000B Gateway and E-SBC IDS Policy Alarm IDS Policy Alarm The alarm is raised whenever a threshold is crossed in the IDS system. The alarm is associated with the MO pair IDSMatch & IDSRule. acidspolicyalarm SNMP OID Default Severity Other Alarm Text Policy NUM (NAME) minor/major/critical threshold (NUM) of REASON cross in global/ip/ip+port scope (triggered by IP) Status Changes Corrective Action 1. Identify additional traps (acidsthresholdcrossnotification) that were sent alongside this Intrusion Detection System (IDS) alarm. 2. Locate the remote hosts (IP addresses) that are specified in the traps. 3. Examine the behavior of those hosts (with regard to the reason specified in the alarm), and attempt to fix incorrect operation. 4. If necessary, change the configured thresholds in the IDS Rule table under the IDS Policy table. Performance Monitoring and Alarm Guide 114 Document #: LTRT-94954

115 Performance Monitoring and Alarm Guide 3. Alarms IDS Threshold Cross Notification IDS Threshold Cross Notification This notiofication is sent for each scope (IP or IP+Port) crossing a threshold of an active alarm. acidsthresholdcrossnotification SNMP OID Default Severity AlarmType Other Alarm Text Threshold cross for scope value IP. Severity=minor/major/critical. Current value=num Status Changes 1. Identify the remote host (IP address / port) on the network which the Intrusion Detection System (IDS) has indicated is malicious. Corrective Action Note that the IDS determines a host to be malicious if it has reached or exceeded a user-defined threshold of malicious attacks (counter). 2. Block the malicious activity. Version Performance Monitoring and Alarms

116 Mediant 1000B Gateway and E-SBC IDS Blacklist Notification IDS Blacklist Notification This alarm notifies when an IP address has been added or removed from a blacklist. acidsblacklistnotification SNMP OID Default Severity Alarm Text securityserviceormechanismviolation thresholdcrossed Added IP * to blacklist Removed IP * from blacklist Status Changes Identify the malicious remote host (IP address / port) that the Intrusion Detection System (IDS) has automatically blacklisted or removed from the blacklist. Corrective Action Note that a host is determined to be malicious if it has reached or exceeded a user-defined threshold of malicious attacks (counter). The malicious source is automatically blacklisted for a user-defined period, after which it is removed from the blacklist. Performance Monitoring and Alarm Guide 116 Document #: LTRT-94954

117 Performance Monitoring and Alarm Guide 3. Alarms Proxy Connectivity Proxy Connectivity Sent when a connection to a specific proxy in a specific Proxy Set is down. The trap is cleared when the proxy connections is up. acproxyconnectivity SNMP OID Alarm Text System#0 Proxy Set Alarm <text> communicationsalarm Network issue (connection fail due to network/routing failure). Proxy issue (proxy is down). AudioCodes device issue. Alarm Severity Condition <text> Corrective Action Indeterminate When connection to the proxy server is lost. Proxy Server <IP address>:<port> is now OUT OF SERVICE 1. Ping the proxy server. If there is no ping, contact your proxy provider. The probable reason is the proxy is down. 2. Ping between the proxy and AudioCodes device. If there is no ping, the problem could be a network/router issue. 3. If you have more than one device connected to this same proxy, check if there are more AudioCodes devices with the same trap event. If this is the case, this could confirm that this is not AudioCodes device issue. 4. Contact AudioCodes support center (support@audiocodes.com) and send a syslog and network capture for this issue. Cleared When connection to the proxy is available again Proxy Server - <IP address>:<port> is now IN SERVICE Version Performance Monitoring and Alarms

118 Mediant 1000B Gateway and E-SBC Web User Activity Log Trap acactivitylog Sent upon log (Syslog) generated by device indicating a Web user action (configured by ActivityListToLog). The SNMP trap notification functionality is enabled by the EnableActivityTrap parameter (refer to the User's Manual). acactivitylog SNMP OID Default Severity Indeterminate Event Type other (0) other (0) Trap Text Note [description of activity].user:<username>. Session: <session type>[ip address of client (user)]. For example: Auxiliary file loading was changed from 0 to 1, User:Admin. Session: WEB [ ] Activity log event is applicable to the following OAMP interfaces: SNMP, Web, CLI and REST. For SNMP activity, the username refers to the SNMP community string. Performance Monitoring and Alarm Guide 118 Document #: LTRT-94954

119 Performance Monitoring and Alarm Guide 3. Alarms This page is intentionally left blank. Version Performance Monitoring and Alarms

120 AudioCodes One Voice Operations Center EMS, SEM and IP Phones Management Performance Monitoring and Alarm Guide