AT60142H/HT. Rad-Hard 512Kx8 Very Low Power CMOS SRAM ERRATA-SHEET. Active Errata List. Errata History. Abbreviations. 1.

Size: px
Start display at page:

Download "AT60142H/HT. Rad-Hard 512Kx8 Very Low Power CMOS SRAM ERRATA-SHEET. Active Errata List. Errata History. Abbreviations. 1."

Transcription

1 AT60142H/HT Rad-Hard 512Kx8 Very Low Power CMOS SRAM ERRATA-SHEET Active Errata List 1. Reading Error Errata History Lot Number Errata List All AT60142H lots 1 All AT60142HT lots 1 Abbreviations ATE : Automated Test Equipment

2 1 Errata Description 1.1 Reading error Issue: An extension of the issue reported on the AT60142F/FT errata-sheet (7776E-AERO-06/08) has been observed on the H/HT versions at application level. However, Atmel has been unable to reproduce it on ATE despite intensive tests and design simulations. This document aims to provide guidelines to work around the issue. Failure conditions The list of symptoms reported below shall not be considered as exhaustive: The memory content is not corrupted as the issue concerns read operations only, The issue was a 0 read fail (expected 0 wrongly read as 1 ) most of time but a 1 read fail (expected 1 wrongly read as 0 ) may also occur, The issue occurs on bits 5 and/or 6 most of the time but other bits may be impacted, The issue depends on the timing of the chip select versus the address bus, The issue is mainly observed in typical conditions (room temperature, nominal voltage) but the entire temperature and voltage ranges must be considered. Issue description: Considering the address bus at T0 time, there is a risk of read errors when the chip select () is driven low within the timing window [T0-TAVAV, T0]. T0-TAVAV T0 Time Read cycle triggered by address Read cycle triggered by chip select Un Case 1 : no read errors Un Case 2 : risk of read errors Un Case 3 : no read errors 2

3 Workaround: To work around the issue, the system shall be designed to have read operations in accordance either with case 1 or case 3 only. To meet this condition, it may be necessary to delay the signals to get out of case 2. There are two solutions: a) delay the entire address bus (A[]) for case 1, b) or delay the chip select () for case 3. However it is obvious that solution b) is the easiest to implement. The aging analysis conducted by Atmel show that the parameters defining the separation window does not change throughout the lifetime of the product. 3

4 2 Revision History Doc Rev. Date Comments B 09/2017 Document updated to provide a more accurate information A 06/2016 Initial document release. 4

5 Atmel Corporation 1600 Technology Drive, San Jose, CA USA T: (+1)(408) F: (+1)(408) Atmel Corporation. / Rev.:. Atmel, Atmel logo and combinations thereof, Enabling Unlimited Possibilities, and others are registered trademarks or trademarks of Atmel Corporation in U.S. and other countries. ARM, ARM Connected logo, and others are the registered trademarks or trademarks of ARM Ltd. Other terms and product names may be trademarks of others. DISCLAIMER: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN THE ATMEL TERMS AND CONDITIONS OF SALES LOCATED ON THE ATMEL WEBSITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS AND PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications and products descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life. SAFETY-CRITICAL, MILITARY, AND AUTOMOTIVE APPLICATIONS DISCLAIMER: Atmel products are not designed for and will not be used in connection with any applications where the failure of such products would reasonably be expected to result in significant personal injury or death ( Safety-Critical Applications ) without an Atmel officer's specific written consent. Safety-Critical Applications include, without limitation, life support devices and systems, equipment or systems for the operation of nuclear facilities and weapons systems. Atmel products are not designed nor intended for use in military or aerospace applications or environments unless specifically AT60142H/HT designated by Atmel as [ERRATA-SHEET] military-grade. Atmel products are not designed nor intended for use in automotive applications unless specifically designated by as automotive-grade. 5

AVR42789: Writing to Flash on the New tinyavr Platform Using Assembly

AVR42789: Writing to Flash on the New tinyavr Platform Using Assembly AVR 8-bit Microcontrollers AVR42789: Writing to Flash on the New tinyavr Platform Using Assembly APPLICATION NOTE Table of Contents 1. What has Changed...3 1.1. What This Means and How to Adapt...4 2.

More information

AT03975: Getting Started with SAM L21. Descripton. Features. SMART ARM-Based Microcontroller APPLICATION NOTE

AT03975: Getting Started with SAM L21. Descripton. Features. SMART ARM-Based Microcontroller APPLICATION NOTE SMART ARM-Based Microcontroller AT03975: Getting Started with SAM L21 APPLICATION NOTE Descripton This application note aims at getting started with the Atmel SAM L21 ARM Cortex -M0+ based microconroller.

More information

AT11512: SAM L Brown Out Detector (BOD) Driver. Introduction. SMART ARM-based Microcontrollers APPLICATION NOTE

AT11512: SAM L Brown Out Detector (BOD) Driver. Introduction. SMART ARM-based Microcontrollers APPLICATION NOTE SMART ARM-based Microcontrollers AT11512: SAM L Brown Out Detector (BOD) Driver APPLICATION NOTE Introduction This driver for Atmel SMART ARM -based microcontrollers provides an interface for the configuration

More information

APPLICATION NOTE. 3-lead CONTACT Package Usage. ATSHA204A, ATECC108A, and ATECC508A. Introduction. 3-lead CONTACT Package

APPLICATION NOTE. 3-lead CONTACT Package Usage. ATSHA204A, ATECC108A, and ATECC508A. Introduction. 3-lead CONTACT Package APPLICATION NOTE 3-lead CONTACT Package Usage ATSHA204A, ATECC108A, and ATECC508A Introduction The Atmel CryptoAuthentication devices are often used in product accessory or product ecosystem management.

More information

APPLICATION NOTE. AT6486: Using DIVAS on SAMC Microcontroller. SMART ARM-Based Microcontroller. Introduction. Features

APPLICATION NOTE. AT6486: Using DIVAS on SAMC Microcontroller. SMART ARM-Based Microcontroller. Introduction. Features APPLICATION NOTE AT6486: Using DIVAS on SAMC Microcontroller SMART ARM-Based Microcontroller Introduction DIVAS stands for Division and Square Root Accelerator. DIVAS is a brand new peripheral introduced

More information

AT03262: SAM D/R/L/C System Pin Multiplexer (SYSTEM PINMUX) Driver. Introduction. SMART ARM-based Microcontrollers APPLICATION NOTE

AT03262: SAM D/R/L/C System Pin Multiplexer (SYSTEM PINMUX) Driver. Introduction. SMART ARM-based Microcontrollers APPLICATION NOTE SMART ARM-based Microcontrollers AT03262: SAM D/R/L/C System Pin Multiplexer (SYSTEM PINMUX) Driver APPLICATION NOTE Introduction This driver for Atmel SMART ARM -based microcontrollers provides an interface

More information

AT09381: SAM D - Debugging Watchdog Timer Reset. Introduction. SMART ARM-based Microcontrollers APPLICATION NOTE

AT09381: SAM D - Debugging Watchdog Timer Reset. Introduction. SMART ARM-based Microcontrollers APPLICATION NOTE SMART ARM-based Microcontrollers AT09381: SAM D - Debugging Watchdog Timer Reset APPLICATION NOTE Introduction This application note shows how the early warning interrupt can be used to debug a WDT reset

More information

APPLICATION NOTE. Generating Random Secrets. ATSHA204A, ATECC108A, and ATECC508A. Description. Topics

APPLICATION NOTE. Generating Random Secrets. ATSHA204A, ATECC108A, and ATECC508A. Description. Topics APPLICATION NOTE Generating Random Secrets ATSHA204A, ATECC108A, and ATECC508A Description When defining a secret that will be used for cryptographic authentication, it is important that the secret is

More information

AT21CS Series Reset and Discovery. Introduction. Serial EEPROM APPLICATION NOTE

AT21CS Series Reset and Discovery. Introduction. Serial EEPROM APPLICATION NOTE Serial EEPROM AT21CS Series Reset and Discovery APPLICATION NOTE Introduction This application note discusses the Atmel AT21CS Series Reset function and the AT21CS Series Discovery function. Additionally,

More information

AVR134: Real Time Clock (RTC) Using the Asynchronous Timer. Features. Introduction. AVR 8-bit Microcontrollers APPLICATION NOTE

AVR134: Real Time Clock (RTC) Using the Asynchronous Timer. Features. Introduction. AVR 8-bit Microcontrollers APPLICATION NOTE AVR 8-bit Microcontrollers AVR134: Real Time Clock (RTC) Using the Asynchronous Timer APPLICATION NOTE Features Real Time Clock with Very Low Power Consumption (10µA @ 3.3V) Very Low Cost Solution Adjustable

More information

AT10942: SAM Configurable Custom Logic (CCL) Driver. Introduction. SMART ARM-based Microcontrollers APPLICATION NOTE

AT10942: SAM Configurable Custom Logic (CCL) Driver. Introduction. SMART ARM-based Microcontrollers APPLICATION NOTE SMART ARM-based Microcontrollers AT10942: SAM Configurable Custom Logic (CCL) Driver APPLICATION NOTE Introduction This driver for Atmel SMART SAM devices provides an interface for the configuration and

More information

ATECC508A Public Key Validation. Introduction. Atmel CryptoAuthentication APPLICATION NOTE

ATECC508A Public Key Validation. Introduction. Atmel CryptoAuthentication APPLICATION NOTE Atmel CryptoAuthentication ATECC508A Public Key Validation APPLICATION NOTE Introduction The Atmel CryptoAuthentication ATECC508A device supports validated public keys if keyconfig.pubinfo is set to one

More information

This user guide describes how to run the Atmel ATWINC3400 Bluetooth Low Energy (BLE) Provisioning demo from out-of-box conditions.

This user guide describes how to run the Atmel ATWINC3400 Bluetooth Low Energy (BLE) Provisioning demo from out-of-box conditions. ATWINC3400 BLE ATWINC3400 BLE Provisioning - Setup and Usage USER GUIDE Introduction This user guide describes how to run the Atmel ATWINC3400 Bluetooth Low Energy (BLE) Provisioning demo from out-of-box

More information

EDBG. Description. Programmers and Debuggers USER GUIDE

EDBG. Description. Programmers and Debuggers USER GUIDE Programmers and Debuggers EDBG USER GUIDE Description The Atmel Embedded Debugger (EDBG) is an onboard debugger for integration into development kits with Atmel MCUs. In addition to programming and debugging

More information

QT3 Xplained Pro. Preface. Atmel QTouch USER GUIDE

QT3 Xplained Pro. Preface. Atmel QTouch USER GUIDE Atmel QTouch QT3 Xplained Pro USER GUIDE Preface The Atmel QT3 Xplained Pro is an extension board, which enables the evaluation of a capacitive touch 12 key numpad in mutual capacitance configuration.

More information

APPLICATION NOTE. AT11008: Migration from ATxmega16D4/32D4 Revision E to Revision I. Atmel AVR XMEGA. Introduction. Features

APPLICATION NOTE. AT11008: Migration from ATxmega16D4/32D4 Revision E to Revision I. Atmel AVR XMEGA. Introduction. Features APPLICATION NOTE AT11008: Migration from ATxmega16D4/32D4 Revision E to Revision I Atmel AVR XMEGA Introduction This application note lists out the differences and changes between Revision E and Revision

More information

AT06467: Getting started with SAM D09/D10/D11. Features. Description. SMART ARM-based Microcontrollers APPLICATION NOTE

AT06467: Getting started with SAM D09/D10/D11. Features. Description. SMART ARM-based Microcontrollers APPLICATION NOTE SMART ARM-based Microcontrollers AT06467: Getting started with SAM D09/D10/D11 APPLICATION NOTE Features Getting started with Atmel SMART SAM D09/D10/D11 microcontrollers and tools Getting started with

More information

Native route discovery algorithm

Native route discovery algorithm Native route discovery algorithm Starting conditions Node 1 needs to send data to node Routing tables are empty There is no direct path between node 1 and node Destination Next hop Destination Next hop

More information

Smart RF Device Family - Getting Started Guide. Features. Description. References ATAN0115 APPLICATION NOTE

Smart RF Device Family - Getting Started Guide. Features. Description. References ATAN0115 APPLICATION NOTE ATAN0115 Smart RF Device Family - Getting Started Guide APPLICATION NOTE Features Introduction to the Smart RF device family, including ATA82xx receivers, the ATA8520 transmitter and ATA85xx transceivers

More information

AT88CK101 HARDWARE USER GUIDE. Atmel CryptoAuthentication Development Kit. Atmel CryptoAuthentication AT88CK101 Daughterboard

AT88CK101 HARDWARE USER GUIDE. Atmel CryptoAuthentication Development Kit. Atmel CryptoAuthentication AT88CK101 Daughterboard AT88CK101 Atmel CryptoAuthentication Development Kit HARDWARE USER GUIDE Atmel CryptoAuthentication AT88CK101 Daughterboard Introduction The Atmel CryptoAuthentication AT88CK101 is a daughterboard that

More information

ATtiny817 QTouch Moisture Demo User Guide. Description. Features. AVR 8-bit Microcontrollers USER GUIDE

ATtiny817 QTouch Moisture Demo User Guide. Description. Features. AVR 8-bit Microcontrollers USER GUIDE AVR 8-bit Microcontrollers ATtiny817 QTouch Moisture Demo User Guide USER GUIDE Description The Atmel ATtiny817 QTouch Moisture Demo Kit demonstrates the high performance capacitive touch support of the

More information

DGILib USER GUIDE Atmel-42771A-DGILib_User Guide-09/2016

DGILib USER GUIDE Atmel-42771A-DGILib_User Guide-09/2016 DGILib USER GUIDE Table of Contents 1. Description...3 2. API...4 2.1. Discovery...4 2.1.1. initialize_status_change_notification... 4 2.1.2. uninitialize_status_change_notification... 4 2.1.3. register_for_device_status_change_notifications...4

More information

USER GUIDE. Atmel QT6 Xplained Pro. Preface

USER GUIDE. Atmel QT6 Xplained Pro. Preface USER GUIDE Atmel QT6 Xplained Pro Preface Atmel QT6 Xplained Pro kit is a Xplained Pro extension board that enables the evaluation of a mutual capacitance touch suface using the Peripheral Touch Controller

More information

ATAES132A Firmware Development Library. Introduction. Features. Atmel CryptoAuthentication USER GUIDE

ATAES132A Firmware Development Library. Introduction. Features. Atmel CryptoAuthentication USER GUIDE Atmel CryptoAuthentication ATAES132A Firmware Development Library USER GUIDE Introduction This user guide describes how to use the Atmel CryptoAuthentication ATAES132A Firmware Development Library with

More information

SAMA5D2 Quad SPI (QSPI) Performance. Introduction. SMART ARM-based Microprocessor APPLICATION NOTE

SAMA5D2 Quad SPI (QSPI) Performance. Introduction. SMART ARM-based Microprocessor APPLICATION NOTE SMART ARM-based Microprocessor SAMA5D2 Quad SPI (QSPI) Performance APPLICATION NOTE Introduction The Atmel SMART SAMA5D2 Series is a high-performance, powerefficient embedded MPU based on the ARM Cortex

More information

Ethernet1 Xplained Pro

Ethernet1 Xplained Pro Ethernet1 Xplained Pro Part Number: ATETHERNET1-XPRO The Atmel Ethernet1 Xplained Pro is an extension board to the Atmel Xplained Pro evaluation platform. The board enables the user to experiment with

More information

APPLICATION NOTE. CryptoAuthentication Personalization Guide. ATSHA204A and ATECC508A. Introduction. Features

APPLICATION NOTE. CryptoAuthentication Personalization Guide. ATSHA204A and ATECC508A. Introduction. Features APPLICATION NOTE CryptoAuthentication Personalization Guide ATSHA204A and ATECC508A Introduction Before using the Atmel CryptoAuthentication ATSHA204A and ATECC508A devices (crypto devices), there are

More information

APPLICATION NOTE. AT04470: Differences between SAM D21 Variants A, B, and L. 32-bit Microcontroller. Introduction

APPLICATION NOTE. AT04470: Differences between SAM D21 Variants A, B, and L. 32-bit Microcontroller. Introduction APPLICATION NOTE AT04470: Differences between SAM D21 Variants A, B, and L 32-bit Microcontroller Introduction This application note describes the differences between A, B, and L variants of SAM D21 devices.

More information

APPLICATION NOTE. How to Securely Switch Atmel s LIN Transceiver ATA6662/ATA6662C to Sleep Mode ATA6662/ATA6662C. Concerning Atmel ATA6662

APPLICATION NOTE. How to Securely Switch Atmel s LIN Transceiver ATA6662/ATA6662C to Sleep Mode ATA6662/ATA6662C. Concerning Atmel ATA6662 APPLICATION NOTE How to Securely Switch Atmel s LIN Transceiver ATA6662/ATA6662C to Sleep Mode ATA6662/ATA6662C Concerning Atmel ATA6662 The goal of this document is to describe how to switch the Atmel

More information

APPLICATION NOTE. Atmel QT4 Xplained Pro User Guide ATAN0114. Preface

APPLICATION NOTE. Atmel QT4 Xplained Pro User Guide ATAN0114. Preface APPLICATION NOTE Atmel QT4 Xplained Pro User Guide ATAN0114 Preface Atmel QT4 Xplained Pro kit is an extension board that enables evaluation of self-capacitance mode proximity and touch using the peripheral

More information

QT2 Xplained Pro. Preface. Atmel QTouch USER GUIDE

QT2 Xplained Pro. Preface. Atmel QTouch USER GUIDE Atmel QTouch QT2 Xplained Pro USER GUIDE Preface Atmel QT2 Xplained Pro kit is an extension board that enables the evaluation of a mutual capacitance touch surface using the Peripheral Touch Controller

More information

APPLICATION NOTE. AT05567: TC Capture on External Interrupt with the Event System on SAM D20. Preface ASF PROJECT DOCUMENTATION

APPLICATION NOTE. AT05567: TC Capture on External Interrupt with the Event System on SAM D20. Preface ASF PROJECT DOCUMENTATION APPLICATION NOTE AT05567: TC Capture on External Interrupt with the Event System on SAM D20 ASF PROJECT DOCUMENTATION Preface This application note shows how to use the event system to capture an external

More information

SAM4 Reset Controller (RSTC)

SAM4 Reset Controller (RSTC) APPLICATION NOTE AT06864: SAM4 Reset Controller (RSTC) ASF PROGRAMMERS MANUAL SAM4 Reset Controller (RSTC) This driver for SAM devices provides an interface for the configuration and management of the

More information

AVR42772: Data Logger Demo Application on XMEGA A1U Xplained Pro. Introduction. Features. AVR XMEGA Microcontrollers APPLICATION NOTE

AVR42772: Data Logger Demo Application on XMEGA A1U Xplained Pro. Introduction. Features. AVR XMEGA Microcontrollers APPLICATION NOTE AVR XMEGA Microcontrollers AVR42772: Data Logger Demo Application on XMEGA A1U Xplained Pro APPLICATION NOTE Introduction This application note covers some of the power saving features of the Atmel XMEGA

More information

APPLICATION NOTE. Atmel AT03261: SAM D20 System Interrupt Driver (SYSTEM INTERRUPT) SAM D20 System Interrupt Driver (SYSTEM INTERRUPT)

APPLICATION NOTE. Atmel AT03261: SAM D20 System Interrupt Driver (SYSTEM INTERRUPT) SAM D20 System Interrupt Driver (SYSTEM INTERRUPT) APPLICATION NOTE Atmel AT03261: SAM D20 System Interrupt Driver (SYSTEM INTERRUPT) ASF PROGRAMMERS MANUAL SAM D20 System Interrupt Driver (SYSTEM INTERRUPT) This driver for SAM D20 devices provides an

More information

Hardware Prerequisites Atmel Xplained Pro Evaluation Kit Atmel WINC1500 extension USB Micro Cable (TypeA / MicroB)

Hardware Prerequisites Atmel Xplained Pro Evaluation Kit Atmel WINC1500 extension USB Micro Cable (TypeA / MicroB) BENCHMARK WINC1500 Wi-Fi Module Benchmark using iperf 2.0.5 Prerequisites Hardware Prerequisites Atmel Xplained Pro Evaluation Kit Atmel WINC1500 extension USB Micro Cable (TypeA / MicroB) Software Prerequisites

More information

ATECC108/ATSHA204 USER GUIDE. Atmel Firmware Library. Features. Introduction

ATECC108/ATSHA204 USER GUIDE. Atmel Firmware Library. Features. Introduction ATECC108/ATSHA204 Atmel Firmware Library USER GUIDE Features Layered and Modular Design Compact and Optimized for 8-bit Microcontrollers Easy to Port Supports I 2 C and Single-Wire Communication Distributed

More information

USER GUIDE. ATWINC1500 Xplained Pro. Preface

USER GUIDE. ATWINC1500 Xplained Pro. Preface USER GUIDE ATWINC1500 Xplained Pro Preface Atmel ATWINC1500 Xplained Pro is an extension board to the Atmel Xplained Pro evaluation platform. The extension board allows to evaluate the Atmel ATWINC1510/1500

More information

64K (8K x 8) Battery-Voltage Parallel EEPROM with Page Write and Software Data Protection AT28BV64B

64K (8K x 8) Battery-Voltage Parallel EEPROM with Page Write and Software Data Protection AT28BV64B Features Single 2.7V to 3.6V Supply Hardware and Software Data Protection Low Power Dissipation 15mA Active Current 20µA CMOS Standby Current Fast Read Access Time 200ns Automatic Page Write Operation

More information

USER GUIDE. Atmel Segment LCD1 Xplained Pro. Preface

USER GUIDE. Atmel Segment LCD1 Xplained Pro. Preface USER GUIDE Atmel Segment LCD1 Xplained Pro Preface Atmel Segment LCD1 Xplained Pro is an extension board to the Atmel Xplained Pro evaluation platform. Segment LCD1 Xplained Pro is designed to kick-start

More information

APPLICATION NOTE. Scope. Reference Documents. Software Ethernet Bridge on SAMA5D3/D4. Atmel SMART SAMA5D3/D4 Series

APPLICATION NOTE. Scope. Reference Documents. Software Ethernet Bridge on SAMA5D3/D4. Atmel SMART SAMA5D3/D4 Series SMART APPLICATION NOTE Software Ethernet Bridge on SAMA5D3/D4 Atmel SMART SAMA5D3/D4 Series Scope The Atmel SMART SAMA5D3/D4 series are high-performance, power-efficient embedded MPUs based on the ARM

More information

APPLICATION NOTE. AT03324: Atmel REB212BSMA-EK Quick Start Guide. Atmel MCU Wireless. Introduction

APPLICATION NOTE. AT03324: Atmel REB212BSMA-EK Quick Start Guide. Atmel MCU Wireless. Introduction APPLICATION NOTE AT03324: Atmel REB212BSMA-EK Quick Start Guide Atmel MCU Wireless This application note briefly describes how to set up and run the pre-flashed applications supplied with the Atmel REB212BSMA

More information

Atmel AVR1619: XMEGA-B1 Xplained Demonstration. 8-bit Atmel Microcontrollers. Application Note. Features. 1 Introduction

Atmel AVR1619: XMEGA-B1 Xplained Demonstration. 8-bit Atmel Microcontrollers. Application Note. Features. 1 Introduction Atmel AVR1619: XMEGA-B1 Xplained Demonstration Features Atmel ATxmega128B1 Atmel XMEGA -B1 Xplained kit compatible On-board LCD display USB 2.0 Full speed composite device - Mass Storage interface with

More information

APPLICATION NOTE. Atmel AVR1638: XMEGA RTC Calibration. 8-bit Atmel Microcontrollers. Features. Introduction

APPLICATION NOTE. Atmel AVR1638: XMEGA RTC Calibration. 8-bit Atmel Microcontrollers. Features. Introduction APPLICATION NOTE Atmel AVR1638: XMEGA RTC Calibration 8-bit Atmel Microcontrollers Features Example software project which performs RTC calibration with help of an external precise clock source Software

More information

APPLICATION NOTE. Atmel AT03160: Migrating Bootloader from ATxmega128A1 to other Atmel XMEGA Devices. Atmel AVR XMEGA. Features.

APPLICATION NOTE. Atmel AT03160: Migrating Bootloader from ATxmega128A1 to other Atmel XMEGA Devices. Atmel AVR XMEGA. Features. APPLICATION NOTE Atmel AT03160: Migrating Bootloader from ATxmega128A1 to other Atmel XMEGA Devices Features Atmel AVR XMEGA bootloader Procedure application C-code sample application for Self Programming

More information

ATtiny104 Xplained Nano. Preface. AVR 8-bit Microcontrollers USER GUIDE

ATtiny104 Xplained Nano. Preface. AVR 8-bit Microcontrollers USER GUIDE AVR 8-bit Microcontrollers ATtiny104 Xplained Nano USER GUIDE Preface The Atmel ATtiny104 Xplained Nano evaluation kit is a hardware platform to evaluate the ATtiny104 microcontroller. Supported by the

More information

AVR32752: Using the AVR32 UC3 Static Memory Controller. 32-bit Microcontrollers. Application Note. Features. 1 Introduction

AVR32752: Using the AVR32 UC3 Static Memory Controller. 32-bit Microcontrollers. Application Note. Features. 1 Introduction AVR32752: Using the AVR32 UC3 Static Memory Controller Features Several Types of Access Supported - 8-bit Access Mode - 16-bit Access Mode Software Configurable - Timing Parameters - Initializations 32-bit

More information

AVR1303: Use and configuration of IR communication module. 8-bit Microcontrollers. Application Note. Features. 1 Introduction

AVR1303: Use and configuration of IR communication module. 8-bit Microcontrollers. Application Note. Features. 1 Introduction AVR1303: Use and configuration of IR communication module Features IrDA 1.4 compatible for baud rates up to 115.2 Kbit/s Selectable transmitter pulse modulation schemes: - 3/16 of baud rate period - Fixed

More information

AT697E. Application Note. Checking AT697E Code for Occurrence of LDF/FPOPd Instructions Sequence with a dependency on an Odd-Numbered Register

AT697E. Application Note. Checking AT697E Code for Occurrence of LDF/FPOPd Instructions Sequence with a dependency on an Odd-Numbered Register Checking AT697E Code for Occurrence of LDF/FPOPd Instructions Sequence with a dependency on an Odd-Numbered Register AT697E This application note provides AT697E users with a description of the procedure

More information

Atmel AT697F. Rad-Hard 32-bit SPARC v8 Processor ERRATA SHEET. Active Errata List

Atmel AT697F. Rad-Hard 32-bit SPARC v8 Processor ERRATA SHEET. Active Errata List Atmel AT697F Rad-Hard 32-bit SPARC v8 Processor ERRATA SHEET Active Errata List 1. Odd-numbered FPU register dependency not properly checked in some doubleprecision FPU operations 2. Anomaly in instruction

More information

USER GUIDE EDBG. Description

USER GUIDE EDBG. Description USER GUIDE EDBG Description The Atmel Embedded Debugger (EDBG) is an onboard debugger for integration into development kits with Atmel MCUs. In addition to programming and debugging support through Atmel

More information

USER GUIDE. Atmel QT1 Xplained Pro. Preface

USER GUIDE. Atmel QT1 Xplained Pro. Preface USER GUIDE Atmel QT1 Xplained Pro Preface Atmel QT1 Xplained Pro kit is an extension board that enables evaluation of self- and mutual capacitance mode using the Peripheral Touch Controller (PTC) module.

More information

AT88RF04C. CryptoRF EEPROM Memory 13.56MHz, 4 Kilobits SUMMARY DATASHEET. Features

AT88RF04C. CryptoRF EEPROM Memory 13.56MHz, 4 Kilobits SUMMARY DATASHEET. Features AT88RF04C CryptoRF EEPROM Memory 13.56MHz, 4 Kilobits SUMMARY DATASHEET Features One of a family of devices with user memory of 4 kilobits to 64 kilobits Contactless 13.56MHz RF communications interface

More information

a clock signal and a bi-directional data signal (SCL, SDA)

a clock signal and a bi-directional data signal (SCL, SDA) Selecting the Best Serial EEPROM Interface Protocol for your Application 1. Introduction Atmel offers Serial Electrically Erasable Programmable Read Only Memories (SEEPROM) to designers wanting to save

More information

USER GUIDE. ZigBit USB Stick User Guide. Introduction

USER GUIDE. ZigBit USB Stick User Guide. Introduction USER GUIDE ZigBit USB Stick User Guide Introduction This user guide describes how to get started with the Atmel ZigBit USB sticks. The ZigBit USB sticks is targeted for evaluating the USB features of the

More information

I/O1 Xplained Pro. Preface. Atmel MCUs USER GUIDE

I/O1 Xplained Pro. Preface. Atmel MCUs USER GUIDE Atmel MCUs I/O1 Xplained Pro USER GUIDE Preface Atmel I/O1 Xplained Pro is an extension board to the Atmel Xplained Pro evaluation platform. I/O1 Xplained Pro is designed to give a wide variety of functionality

More information

AT07942: SAM4L Asynchronous Timer (AST) Driver. Introduction. SMART ARM-based Microcontrollers APPLICATION NOTE

AT07942: SAM4L Asynchronous Timer (AST) Driver. Introduction. SMART ARM-based Microcontrollers APPLICATION NOTE SMART ARM-based Microcontrollers AT07942: SAM4L Asynchronous Timer (AST) Driver APPLICATION NOTE Introduction This driver for Atmel SMART ARM -based microcontrollers provides an interface for the configuration

More information

RELEASE NOTES. GNU Toolchain for Atmel ARM Embedded Processors. Introduction

RELEASE NOTES. GNU Toolchain for Atmel ARM Embedded Processors. Introduction RELEASE NOTES GNU Toolchain for Atmel ARM Embedded Processors Introduction The Atmel ARM GNU Toolchain (6.3.1.508) supports Atmel ARM devices. The ARM toolchain is based on the free and open-source GCC.

More information

APPLICATION NOTE. Atmel AT03304: SAM D20 I 2 C Slave Bootloader SAM D20. Description. Features

APPLICATION NOTE. Atmel AT03304: SAM D20 I 2 C Slave Bootloader SAM D20. Description. Features APPLICATION NOTE Atmel AT03304: SAM D20 I 2 C Slave Bootloader SAM D20 Description As many electronic designs evolve rapidly there is a growing need for being able to update products, which have already

More information

USER GUIDE. Atmel OLED1 Xplained Pro. Preface

USER GUIDE. Atmel OLED1 Xplained Pro. Preface USER GUIDE Atmel OLED1 Xplained Pro Preface Atmel OLED1 Xplained Pro is an extension board to the Atmel Xplained Pro evaluation platform. The board enables the user to experiment with user interface applications

More information

AT88SC3216CRF. CryptoRF EEPROM Memory 13.56MHz, 32 Kilobits SUMMARY DATASHEET. Features

AT88SC3216CRF. CryptoRF EEPROM Memory 13.56MHz, 32 Kilobits SUMMARY DATASHEET. Features AT88SC3216CRF CryptoRF EEPROM Memory 13.56MHz, 32 Kilobits SUMMARY DATASHEET Features One of a family of devices with user memory of 1 kilobit to 64 kilobits Contactless 13.56MHz RF communications interface

More information

MySonicWall Secure Upgrade Plus

MySonicWall Secure Upgrade Plus June 2017 This guide describes how to upgrade a SonicWall or competitor appliance in MySonicWall using the Secure Upgrade Plus feature. Topics: About Secure Upgrade Plus Using Secure Upgrade Plus About

More information

AVR1315: Accessing the XMEGA EEPROM. 8-bit Microcontrollers. Application Note. Features. 1 Introduction

AVR1315: Accessing the XMEGA EEPROM. 8-bit Microcontrollers. Application Note. Features. 1 Introduction AVR1315: Accessing the XMEGA EEPROM Features I/O-mapped access Memory-mapped access Split erase and write operations supported Efficient page-oriented access Driver source code included 1 Introduction

More information

USER GUIDE. Atmel maxtouch Xplained Pro. Preface

USER GUIDE. Atmel maxtouch Xplained Pro. Preface USER GUIDE Atmel maxtouch Xplained Pro Preface Atmel maxtouch Xplained Pro is an extension board to the Atmel Xplained Pro evaluation platform. The board enables the user to experiment with user interface

More information

APPLICATION NOTE. AT07216: SAM G55 Schematic Checklist. Atmel SMART SAM G55. Introduction

APPLICATION NOTE. AT07216: SAM G55 Schematic Checklist. Atmel SMART SAM G55. Introduction APPLICATION NOTE AT07216: SAM G55 Schematic Checklist Atmel SMART SAM G55 Introduction A good hardware design comes from a proper schematic. Since SAM G55 devices have a fair number of pins and functions,

More information

AT91 ARM Thumb Microcontrollers. Application Note. Using the ECC Controller on AT91SAM9260/9263 and AT91SAM7SE Microcontrollers. 1.

AT91 ARM Thumb Microcontrollers. Application Note. Using the ECC Controller on AT91SAM9260/9263 and AT91SAM7SE Microcontrollers. 1. Using the ECC Controller on AT91SAM9260/9263 and AT91SAM7SE Microcontrollers 1. Scope The purpose of this document is to explain how to use the Error Corrected Code (ECC) Controller embedded in the AT91SAM9260/9263

More information

AVR4018: Inertial Two (ATAVRSBIN2) Hardware User's Guide. 8-bit Microcontrollers. Application Note. Features. 1 Introduction

AVR4018: Inertial Two (ATAVRSBIN2) Hardware User's Guide. 8-bit Microcontrollers. Application Note. Features. 1 Introduction AVR4018: Inertial Two (ATAVRSBIN2) Hardware User's Guide Features Compatible with all Atmel AVR Xplain MCU boards Full nine-degree-of-freedom inertial sensing InvenSense three-axis MEMS gyroscope (IMU-3000

More information

APPLICATION NOTE. Atmel AVR536: Migration from ATmega644 to ATmega644A. 8-bit Atmel Microcontrollers. Introduction

APPLICATION NOTE. Atmel AVR536: Migration from ATmega644 to ATmega644A. 8-bit Atmel Microcontrollers. Introduction APPLICATION NOTE Atmel AVR536: Migration from ATmega644 to ATmega644A 8-bit Atmel Microcontrollers Introduction The Atmel ATmega644A is a functionally identical, drop-in replacement for the Atmel ATmega644.

More information

OLED display with pixels resolution Ambient light sensor CPU load Analog filter Quadrature Encoder with push button Digital I/O

OLED display with pixels resolution Ambient light sensor CPU load Analog filter Quadrature Encoder with push button Digital I/O APPLICATION NOTE Atmel AT02657: XMEGA-E5 Xplained Software User Guide Features OLED display with 128 32 pixels resolution Ambient light sensor CPU load Analog filter Quadrature Encoder with push button

More information

Atmel LF-RFID Kit Comparison Chart. Application Note. Atmel LF-RFID Kit Comparison Chart. 1. Description

Atmel LF-RFID Kit Comparison Chart. Application Note. Atmel LF-RFID Kit Comparison Chart. 1. Description Atmel LF-RFID Kit Comparison Chart 1. Description Atmel offers several types of development and evaluation kits. The Atmel ATA2270-EK1 is an evaluation kit that supports a limited number of modes in stand-alone

More information

SMART ARM-based Microcontrollers ATSAMD21E16LMOTOR USER GUIDE

SMART ARM-based Microcontrollers ATSAMD21E16LMOTOR USER GUIDE SMART ARM-based Microcontrollers ATSAMD21E16LMOTOR USER GUIDE Table of Contents 1. ATSAMD21E16L Microcontroller Card for Atmel Motor Control Starter Kit... 3 2. ATSAMD21E16LMOTOR Features... 4 3. ATSAMD21E16LMOTOR

More information

Atmel AVR32847: Migration from/to the UC3L0 64/32/16 from/to the UC3L0 256/ bit Atmel Microcontrollers. Application Note.

Atmel AVR32847: Migration from/to the UC3L0 64/32/16 from/to the UC3L0 256/ bit Atmel Microcontrollers. Application Note. Atmel AVR32847: Migration from/to the UC3L0 64/32/16 from/to the UC3L0 256/128 Features Features comparison Porting considerations and tools Pinout comparison 1 Introduction This application note is a

More information

Atmel QT600 Quick Start Guide Touch Solutions

Atmel QT600 Quick Start Guide Touch Solutions Atmel QT600 Quick Start Guide Touch Solutions Introduction Looking to take your design to the next level? You have made the right choice in purchasing the Atmel QT600 Development Kit. It allows you to

More information

APPLICATION NOTE. Atmel AT01080: XMEGA E Schematic Checklist. Atmel AVR XMEGA E. Features. Introduction

APPLICATION NOTE. Atmel AT01080: XMEGA E Schematic Checklist. Atmel AVR XMEGA E. Features. Introduction APPLICATION NOTE Atmel AT01080: XMEGA E Schematic Checklist Atmel AVR XMEGA E Features Power supplies Reset circuit Clocks and crystal oscillators PDI TWI Introduction This application note describes a

More information

ATECC108. Atmel CryptoAuthentication SUMMARY DATASHEET. Features. Applications NOT RECOMMENDED FOR NEW DESIGNS. Replaced by ATECC108A

ATECC108. Atmel CryptoAuthentication SUMMARY DATASHEET. Features. Applications NOT RECOMMENDED FOR NEW DESIGNS. Replaced by ATECC108A ATECC08 Atmel CryptoAuthentication NOT RECOMMENDED FOR NEW DESIGNS Replaced by ATECC08A Features Secure authentication and product validation device High-Speed Public Key Algorithm (PKI) Crypto Engine

More information

USER GUIDE. Wireless Production Test Reference Protocol Specification Document. Atmel MCU Wireless. Description

USER GUIDE. Wireless Production Test Reference Protocol Specification Document. Atmel MCU Wireless. Description USER GUIDE Wireless Production Test Reference Protocol Specification Document Atmel MCU Wireless Description This document explains the serial protocol used for communication between various blocks of

More information

AVR1503: Xplain training - XMEGA Programmable Multi Interrupt Controller 8-bit Microcontrollers Application Note Prerequisites

AVR1503: Xplain training - XMEGA Programmable Multi Interrupt Controller 8-bit Microcontrollers Application Note Prerequisites AVR1503: Xplain training - XMEGA Programmable Multi Interrupt Controller Prerequisites Required knowledge Completed AVR1500 XMEGA Basics training Software prerequisites Atmel AVR Studio 4.18 SP2 or later

More information

AVR532: Migration from ATmega48/88/168 to ATmega48A/88A/168A. 8-bit Microcontrollers. Application Note. 1 Introduction

AVR532: Migration from ATmega48/88/168 to ATmega48A/88A/168A. 8-bit Microcontrollers. Application Note. 1 Introduction AVR532: Migration from ATmega48/88/168 to ATmega48A/88A/168A 1 Introduction The ATmega48A/88A/168A is a functionally identical, drop-in replacement for the ATmega48/88/168. All devices are subject to the

More information

Atmel AT697F. Rad-Hard 32-bit SPARC v8 Processor ERRATA SHEET. Active Errata List

Atmel AT697F. Rad-Hard 32-bit SPARC v8 Processor ERRATA SHEET. Active Errata List Atmel AT697F Rad-Hard 32-bit SPARC v8 Processor ERRATA SHEET Active Errata List 1. Odd-numbered FPU register dependency not properly checked in some doubleprecision FPU operations 2. Anomaly in instruction

More information

DATASHEET 4D SYSTEMS. 4D Raspberry Pi Serial Adaptor TURNING TECHNOLOGY INTO ART. 4D-Serial-Pi-Adaptor

DATASHEET 4D SYSTEMS. 4D Raspberry Pi Serial Adaptor TURNING TECHNOLOGY INTO ART. 4D-Serial-Pi-Adaptor TURNING TECHNOLOGY INTO ART DATASHEET 4D-Serial-Pi-Adaptor Document Date: 20 th November 2012 Document Revision: 1.0 Uncontrolled Copy when printed or downloaded. Please refer to the 4D Systems website

More information

Application Note Using the ATV750, ATV750B, and ATF750C Erasable Programmable Logic Device Introduction 1.1 Device Names and Pin/Node Assignments

Application Note Using the ATV750, ATV750B, and ATF750C Erasable Programmable Logic Device Introduction 1.1 Device Names and Pin/Node Assignments Application Note Using the ATV750, ATV750B, and ATF750C Erasable Programmable Logic Device 1. Introduction This application note describes how to use the features of the ATV750, ATV750B, and ATF750C in

More information

How to Show Grouping in Scatterplots using Statistica

How to Show Grouping in Scatterplots using Statistica How to Show Grouping in Scatterplots using Statistica Written by Dell Software Introduction A scatterplot shows the relationship between continuous variables. Showing a grouping factor in the plot adds

More information

DATASHEET 4D SYSTEMS. 4D Arduino Adaptor Shield TURNING TECHNOLOGY INTO ART. 4Display-Adaptor-Shield

DATASHEET 4D SYSTEMS. 4D Arduino Adaptor Shield TURNING TECHNOLOGY INTO ART. 4Display-Adaptor-Shield TURNING TECHNOLOGY INTO ART DATASHEET 4Display-Adaptor-Shield Document Date: 20 th November 2012 Document Revision: 1.0 Uncontrolled Copy when printed or downloaded. Please refer to the 4D Systems website

More information

One Identity Quick Connect Express

One Identity Quick Connect Express One Identity Quick Connect Express for Active Directory 5.6.0 October 2017 These release notes provide information about the One Identity Quick Connect Express for Active Directory release. About New features

More information

AVR1518: XMEGA-A1 Xplained Training - XMEGA Clock System. 8-bit Atmel Microcontrollers. Application Note. Prerequisites.

AVR1518: XMEGA-A1 Xplained Training - XMEGA Clock System. 8-bit Atmel Microcontrollers. Application Note. Prerequisites. AVR1518: XMEGA-A1 Xplained Training - XMEGA Clock System Prerequisites Required knowledge - Basic knowledge of microcontrollers and the C programming language - Completed AVR1512 XMEGA-A1 Xplained Training

More information

DATASHEET 4D SYSTEMS. 4D Raspberry Pi Serial Adaptor TURNING TECHNOLOGY INTO ART. 4D-Serial-Pi-Adaptor

DATASHEET 4D SYSTEMS. 4D Raspberry Pi Serial Adaptor TURNING TECHNOLOGY INTO ART. 4D-Serial-Pi-Adaptor DATASHEET TURNING TECHNOLOGY INTO ART 4D Raspberry Pi Serial Adaptor 4D-Serial-Pi-Adaptor Document Date: 4 th September 2013 Document Revision: 1.1 Uncontrolled Copy when printed or downloaded. Please

More information

AVR32401: AVR32 AP7 Linux Interfacing DataFlash. 8-bit Microcontrollers. Application Note. Features. 1 Introduction

AVR32401: AVR32 AP7 Linux Interfacing DataFlash. 8-bit Microcontrollers. Application Note. Features. 1 Introduction AVR32401: AVR32 AP7 Linux Interfacing DataFlash Features JFFS2 file system Communication through SPI interface 1 Introduction This application note serves as an example of how to connect, set up and use

More information

APPLICATION NOTE. Atmel AT02260: Driving AT42QT1085. Atmel QTouch. Features. Description

APPLICATION NOTE. Atmel AT02260: Driving AT42QT1085. Atmel QTouch. Features. Description APPLICATION NOTE Atmel AT02260: Driving AT42QT1085 Atmel QTouch Features Overview of Atmel AT42QT1085 Circuit configuration with Host MCU SPI communication Demonstration program Description This application

More information

APPLICATION NOTE. AT06863: SAM4L Peripheral Event Controller (PEVC) SAM4L Peripheral Event Controller (PEVC) ASF PROGRAMMERS MANUAL

APPLICATION NOTE. AT06863: SAM4L Peripheral Event Controller (PEVC) SAM4L Peripheral Event Controller (PEVC) ASF PROGRAMMERS MANUAL APPLICATION NOTE AT06863: SAM4L Peripheral Event Controller (PEVC) ASF PROGRAMMERS MANUAL SAM4L Peripheral Event Controller (PEVC) This driver provides a unified interface for the configuration and management

More information

DATASHEET 4D SYSTEMS. 4D Raspberry Pi Serial Adaptor TURNING TECHNOLOGY INTO ART. 4D-Serial-Pi-Adaptor

DATASHEET 4D SYSTEMS. 4D Raspberry Pi Serial Adaptor TURNING TECHNOLOGY INTO ART. 4D-Serial-Pi-Adaptor DATASHEET TURNING TECHNOLOGY INTO ART 4D Raspberry Pi Serial Adaptor 4D-Serial-Pi-Adaptor Document Date: 21 st August 2014 Document Revision: 1.2 Uncontrolled Copy when printed or downloaded. Please refer

More information

APPLICATION NOTE. Atmel AT03782: Using Low Power Modes in SAM4N Microcontroller. Atmel 32-bit Microcontroller. Features.

APPLICATION NOTE. Atmel AT03782: Using Low Power Modes in SAM4N Microcontroller. Atmel 32-bit Microcontroller. Features. APPLICATION NOTE Atmel AT03782: Using Low Power Modes in SAM4N Microcontroller Atmel 32-bit Microcontroller Features Low power modes in SAM4N Power supply in SAM4N Introduction The purpose of this application

More information

APPLICATION NOTE. Atmel AVR3009: Driving QTouch Device with I 2 C Interface. Atmel QTouch. Introduction

APPLICATION NOTE. Atmel AVR3009: Driving QTouch Device with I 2 C Interface. Atmel QTouch. Introduction APPLICATION NOTE Atmel AVR3009: Driving QTouch Device with I 2 C Interface Introduction Atmel QTouch This application note explains the communication of I 2 C-Compatible Master microcontroller with Atmel

More information

SonicWall Mobile Connect for Chrome OS

SonicWall Mobile Connect for Chrome OS SonicWall Mobile Connect 5.0.1 for Chrome OS November 2017 These release notes provide information about the SonicWall release. Topics: About Supported Platforms New Features Resolved Issues Known Issues

More information

STK521. User Guide B AVR 01/12

STK521. User Guide B AVR 01/12 STK521... User Guide Table of Contents Section 1 1 Introduction 1 Features 2 Section 2 3 Using the STK521 Top Module 3 Connecting the Atmel STK521 to the Atmel STK500 Starter Kit 3 Powering the STK521

More information

Atmel and the use of Verilator to create uc Device Models

Atmel and the use of Verilator to create uc Device Models Atmel and the use of Verilator to create uc Device Models Dag Braend Sr Director Atmel MCU Tools Roland Kruse Jie Xu Jan Egil Ruud Atmel Co-simulation Team 1 2012 Copyright Atmel Corporation 14/Jan/2013

More information

32Kbytes on-chip SRAM. Viterbi decoding and CRC PRIME compliant 128-bit AES encryption Channel sensing and collision pre-detection

32Kbytes on-chip SRAM. Viterbi decoding and CRC PRIME compliant 128-bit AES encryption Channel sensing and collision pre-detection Atmel ATPL220A PRIME compliant Power Line Communications Modem Features SUMMARY DATASHEET Modem Power Line Carrier Modem for 50 and 60 Hz mains 97-carrier OFDM PRIME compliant Baud rate Selectable: 21400

More information

Atmel ATtiny1634 MCU Atmel ATA SBC LIN transceiver with integrated voltage regulator Touch. Three Atmel QTouch buttons One Atmel QTouch slider

Atmel ATtiny1634 MCU Atmel ATA SBC LIN transceiver with integrated voltage regulator Touch. Three Atmel QTouch buttons One Atmel QTouch slider APPLICATION NOTE ATtiny1634-EK1 User Guide ATAN0080 Features Atmel ATtiny1634 MCU Atmel ATA663254 SBC LIN transceiver with integrated voltage regulator Touch Three Atmel QTouch buttons One Atmel QTouch

More information

APPLICATION NOTE. Atmel AVR057: Internal RC Oscillator Calibration for ATtiny4/5/9/10/20/40. 8-bit Atmel Microcontrollers. Features.

APPLICATION NOTE. Atmel AVR057: Internal RC Oscillator Calibration for ATtiny4/5/9/10/20/40. 8-bit Atmel Microcontrollers. Features. APPLICATION NOTE Features Atmel AVR057: Internal RC Oscillator Calibration for ATtiny4/5/9/10/20/40 8-bit Atmel Microcontrollers Calibration of the internal 8MHz RC Oscillator for Atmel ATtiny4/5/9/10/20/40

More information

8-megabyte, 4-megabyte, and 2-megabyte 2.7-volt Only DataFlash Cards AT45DCB008D AT45DCB004D AT45DCB002D. Not Recommended for New Design

8-megabyte, 4-megabyte, and 2-megabyte 2.7-volt Only DataFlash Cards AT45DCB008D AT45DCB004D AT45DCB002D. Not Recommended for New Design Features MultiMediaCard (MMC) Form Factor Single 2.7V to 3.6V Supply 66 MHz Max Clock Frequency Serial Peripheral Interface (SPI) Compatible Low Power Dissipation 10 ma Active Read Current Typical 25 µa

More information

ATZB-SAMR21-XPRO. Preface. SmartConnect USER GUIDE

ATZB-SAMR21-XPRO. Preface. SmartConnect USER GUIDE SmartConnect ATZB-SAMR21-XPRO USER GUIDE Preface This user guide facilitates how to get started with the Atmel ATZB-SAMR21- XPRO extension board. ATZB-SAMR21-XPRO is targeted for evaluating the features

More information