Serial Connection of HC900 Hybrid Controller to 900CS Control Station

Size: px
Start display at page:

Download "Serial Connection of HC900 Hybrid Controller to 900CS Control Station"

Transcription

1 Note: Ethernet connections will provide faster performance than RS-485 HC Remove HC900 CPU and set S2 Dip Switches for RS-485 unterminated Replace CPU & follow instructions per Installation and User Guide# , table-10 HC900 S2 Port Dip Switches 1b Page 1 of 9

2 Open your HC900.cde control file in Hybrid Control Designer Note: You must be connected to the HC900 controller to perform this step 2.a Click to select the Utilities tab 2.b Click to select the Set Controller Serial Ports Icon 2b 2a Page 2 of 9

3 2.c Click on tab: Serial-S2 2.d Click on radio button: Modbus RTU Slave Change Slave Type to: Point to Point Slave Address: 1 Modbus Slave Double Register Format: FP B Big Endian [4,3,2,1] Port Enabled: Enabled Slect Speed: (9600, 19200, 38400, 57600, ) Typical is: Modbus Parity: none Modbus Stop Bits: 1 2c 2d 2.e Save the file Page 3 of 9

4 900CS Station Designer Software 3. Open Station Designer software 3a 3.a Click on Communications in the Navigation Pane 3.b Select RS485 Comm Port 3.c Driver should have No Driver Selected 3.d If Clear Port Settings is not grayed out, click this 3c 3b 3d Page 4 of 9

5 4.a Click on: Pick 4a 4.b Select Manufacturer: Honeywell 4.c Select Driver: HC-900 Serial 4.d Click OK 4b 4c 4d Page 5 of 9

6 4.e Select the same Baud Rate as in step 1.d (default for all other Port Settings) 4e 4.f Save file Station Designer file Page 6 of 9

7 Communication Cable 5. Fabricate a Serial cable 5.a Take a Cat-5 (or better) Shielded Patch cable and cut off one end 5.b Remove Shield contact from 900CS/ RJ-45 side of cable 5.c Refer to table below and cut unused wires in the cable and insulate with heat shrink tubing or other appropriate insulating material. (Typical conductor insulation colors are shown) 5.d Twist common leads together and then trim to required insertion ~ ¼ inch (verify insulation is not in contact with lock-down bar of connector) 5.e Terminate leads to HC900 S2 Serial Connector 5.f Connect RJ-45 to RS485 Port A of 900CS (illustration on next page) 5.g Connect 3-plug connector to Port S2 on the HC900 CPU (illustration on next page) Shield Orange/ White Orange Brown/ White Brown Page 7 of 9

8 900CS Ports Note: Install dedicated ground wire from 900CS Ground Terminal to Control Panel Earth Ground HC900 S2 Serial Port Page 8 of 9

9 Page 9 of 9

10 Main Menu Communications Menu Overview Communications Menu Overview Menu Submenu Serial Port S1 (p. 28) Serial Port S2 (p. 28) Ethernet Port E1 (p. 33) Ethernet Port E2 (p. 33) Expansion Port Communications (p. 35) Modbus Slave Devices (p. 37) Modbus Slave Device n Modbus/TCP Slave Device n Modbus Slave n Status Modbus/TCP Slave n Status Host Connections (p. 38) Host Connection n Host Connection n Status Peer Connections (p. 39) Peer Connections n Peer Connection n Status Serial Port S1/S2 The Serial Port S1 and Serial Port S2 screens both show Statistics (Table 6) and Settings (Table 8) for those controller serial ports. Table 9 shows the relationship between the setup parameters and each protocol. The controller s Serial Port S1 can be set-up as an ELN Configuration port, a Modbus Master port, or a Modbus Slave port. The ELN protocol allows the controller to communicate with the Hybrid Control Designer package on the PC using the proprietary ELN protocol. The Modbus Master protocols allow the controller to act as a Modbus Master, retrieving data from other instruments that have been configured as Modbus slave devices. The three Modbus Slave protocols allow the controller to act as a slave to various host devices, including a PC running HC Designer. The information presented in Table 6 and Table 9 also applies to Serial Port S1 when a Redundant Controller is used. Table 6 Serial Port S1/S2 Statistics (left side of display) Item Port Diagnostic Description Shows the overall condition of the Serial Port S1. See the list of Serial Port S1 diagnostic conditions in Table 7 on page Control Station User Guide Revision 1 4/09

11 Serial Port S1/S2 Main Menu Communications Item Port Status Messages Received Data Link Errors Application Errors Clear Statistics Description This is the current status of the port. The possible status conditions are: GOOD: the protocol is set to ELN. REQUIRES SETUP: the protocol is set to one of the Modbus Slave protocols, and the Slave Address is set to 255. Messages on the communication link are ignored in this state. OFFLINE: the protocol is set to one of the Modbus Slave protocols, and the Slave Port Enable is set to DISABLE. Messages on the communication link are ignored in this state. ONLINE: the protocol is set to one of the Modbus Slave protocols, and the Slave Port Enable is set to ENABLE. Messages on the communication link are being processed in this state. NO MODBUS SLAVE BLOCKS: the protocol is set to one of the Modbus Slave protocols, but there are no Modbus slave function blocks present in the controller s configuration. PROGRAM MODE: the protocol is set to one of the Modbus Slave protocols, but the controller is in Program Mode. The controller does not scan the slave devices in this state. ELN SLAVE: the protocol is set to one of the Modbus Slave protocols, but the controller is in Program Locked Mode. The port automatically reverts to ELN protocol and the controller becomes a slave device whenever the mode selection switch is placed in the Program Locked position. SCANNING SLAVES: the protocol is set to one of the Modbus Slave protocols, and the controller is actively scanning the slave devices attached to the port. The number of messages that were received and processed correctly. The number of basic link-level errors detected by the controller. If the protocol is Modbus Master, the errors may be due to a slave device that does not reply when it is scanned. Refer to the section Troubleshooting Data Link Errors (page 41) for more information. The number of messages that were responded to with an exception code. For example, application errors can be caused by (a) writing to a read-only register, (b) accessing a register that is not supported by the slave device, or (c) using a Modbus function code that is not supported by the slave device. This item resets the message counters for this port back to zero (Messages Received, Data Link Errors, and Application Errors). Note: the counters will only be reset if the controller is in Run Mode. Revision Control Station User Guide 29 4/09

12 Main Menu Communications Serial Port S1/S2 Table 7 Serial Port S1/S2: Port Diagnostic status Status Possible Cause Controller Action What to do GOOD N/A N/A N/A APPLICATION ERROR DATA LINK ERROR HARDWARE FAILURE Applies to Port S2 only. At least one response to a host resulted in an exception code or NAK. A large number of messages are resulting in data link errors. The DUART is failing to operate properly. 1. Rack 1 monitor block s COMPORT DIAG is set to WARNING. 2. Rack 1 monitor block s RACK OK pin is turned off. 3. SYSTEM MONITOR block s HW OK pin is turned off. 1. Rack 1 monitor block s COMPORT DIAG is set to FAILED. 2. Rack 1 monitor block s RACK OK pin is turned off. 3. SYSTEM MONITOR block s HW OK pin is turned off. 4. If configured as Modbus Master port, associated slave blocks have their read pin values frozen to the last value read. At host, determine which message is causing the exception code and fix it. 1. Check baud rate. 2. Check connectors. 3. Check cable polarity. 4. Isolate cable from electrical interference. 5. If RS232-to-RS485 converter used, check its power, switch/jumper settings, and polarity. Replace the controller CPU module Control Station User Guide Revision 1 4/09

13 Serial Port S1/S2 Main Menu Communications Table 8 Serial Port S1/S2 Settings (right side of display) Setting Description Protocol ELN: The default protocol, used to communicate with the HC Designer configuration software. MODBUS MASTER: The controller acts as a Modbus Master device on the communication link. MB MASTER ADVANCED: The controller acts as a Modbus Master device on the communication link. This protocol provides enhanced data throughput for applications where the HC900 is being used with a Modbus-to-fieldbus gateway device. MODBUS SLAVE MULTI: The controller acts as a Modbus Slave device. This protocol allows more than one slave device to be present on the communications link (multi-drop). MODBUS SLAVE PTP: The controller acts as a Modbus Slave device. This protocol can be used if the controller is the only slave device on the link (Point-topoint). MODBUS SLAVE MODEM: The controller acts as a Modbus Slave device. This protocol provides the extended delays that are needed to access the controller via a modem. Baud Rate (Bps) Modbus Parity Modbus Stop Bits Slave Address (1-247 or 255) Slave Port Enable Select 9600, 19200, 38400, or bits per second. Select None, Odd, or Even parity. Select 1 or 2 Stop Bits. This is the address of the controller on the Modbus link when one of the three Modbus Slave protocols is selected. All devices on the link must have a unique Modbus address. The address may be set to a value of 1 to 247, or it may be set to 255. A value of 255 disables the port for this controller. This item allows you to enable or disable the port: ENABLE: The port will respond to communication requests. DISABLE: The port will ignore communication requests. Double Register Format Under the Modbus protocol, each IEEE 32-bit floating-point number requires two consecutive Modbus registers, for a total of four bytes. The stuffing order of the bytes within these registers differs among Modbus devices. To provide compatibility with the various hosts, the double-register format is configurable. The selections are: FP B Big Endian format Byte order: 4, 3, 2, 1 FP L Little Endian format Byte order: 1, 2, 3, 4 FP BB Big Endian with byte-swap Byte order: 3, 4, 1, 2 FP LB Little Endian with byte-swap Byte order: 2, 1, 4, 3 Revision Control Station User Guide 31 4/09

14 Main Menu Communications Serial Port S1/S2 Table 9 Protocol selection versus setup parameters for the Serial Port S1/S2 Protocol selection Setup parameter ELN Modbus Master or Modbus Master Advanced Modbus Slave Multidrop Modbus Slave Point to Point (PTP) Modbus Slave Modem Baud Rate (BPS) X X X X X Modbus Parity X X X NONE Modbus Stop Bits X X X 1 BIT Slave Address X X X Slave Port Enable X X X Double Register Format X X X Note: When Modbus Slave Modem protocol is selected, the Modbus Parity and Modbus Stop Bits are fixed at None and 1 Bit respectively and cannot be changed Control Station User Guide Revision 1 4/09

HC900 Controller. Controller CPU and Scanner Module Installation and Replacement

HC900 Controller. Controller CPU and Scanner Module Installation and Replacement HC900 Controller and Scanner Module Installation and Replacement Scanner 1 Scanner 2 (for redundant controller) 900C51 - (current revision number) 900C52 - (current revision number) 900C31 - (current revision

More information

Intech Micro 2300-A8VI analogue input station MODBUS RTU slave application supplementary manual.

Intech Micro 2300-A8VI analogue input station MODBUS RTU slave application supplementary manual. Intech Micro 2300-A8VI analogue input station MODBUS RTU slave application supplementary manual. MODBUS supplementary manual to the 2300-A8VI Installation Guide. The 2300 series stations are designed to

More information

QUCM Limitorque Controller

QUCM Limitorque Controller QUCM Limitorque Valve Controller Application Manual QUCM Limitorque Controller Installation and Programming Manual This Manual describes the QUCM application for interfacing Limitorque Valve Actuators

More information

Intech Micro 2300-RO4 analogue input station MODBUS RTU slave application supplementary manual.

Intech Micro 2300-RO4 analogue input station MODBUS RTU slave application supplementary manual. Intech Micro 2300-RO4 analogue input station MODBUS RTU slave application supplementary manual. MODBUS supplementary manual to the 2300-RO4 Installation Guide. The 2300 series stations are designed to

More information

Intech Micro 2300-RTD6 analogue input station MODBUS RTU slave application supplementary manual.

Intech Micro 2300-RTD6 analogue input station MODBUS RTU slave application supplementary manual. Intech Micro 2300-RTD6 analogue input station MODBUS RTU slave application supplementary manual. MODBUS supplementary manual to the 2300-RTD6 Installation Guide. The 2300 series stations are designed to

More information

4511 MODBUS RTU. Configuration Manual. HART transparent driver. No. 9107MCM102(1739) For 4511 devices from ser. no:

4511 MODBUS RTU. Configuration Manual. HART transparent driver. No. 9107MCM102(1739) For 4511 devices from ser. no: 4511 MODBUS RTU Configuration Manual HART transparent driver No. 9107MCM102(1739) For 4511 devices from ser. no: 141590001 9107 CONTENTS Introduction... 3 Modbus basics... 3 Modbus RTU... 3 4511 Supported

More information

VISY-Command. Technical Documentation. with Modbus Protocol. Edition: Version: 1 Art. no.:

VISY-Command. Technical Documentation. with Modbus Protocol. Edition: Version: 1 Art. no.: Technical Documentation with Modbus Procol Edition: 2017-04 Version: 1 Art. no.: 350253 FAFNIR GmbH Schnackenburgallee 149 c 22525 Hamburg Germany Tel.: +49 / 40 / 39 82 07-0 Fax: +49 / 40 / 390 63 39

More information

4511 MODBUS RTU. Configuration Manual. Solenoid / alarm driver. No. 9203MCM100(1328)

4511 MODBUS RTU. Configuration Manual. Solenoid / alarm driver. No. 9203MCM100(1328) 4511 MODBUS RTU Configuration Manual Solenoid / alarm driver 9203MCM100(1328) 9203 CONTENTS Introduction... 3 Modbus basics... 3 Modbus RTU... 3 Supported Function Codes... 3 Modbus Parameters and factory

More information

4511 MODBUS RTU. Configuration Manual. Pulse isolator. No. 9202MCM101(1707) For 4511 devices from ser. no:

4511 MODBUS RTU. Configuration Manual. Pulse isolator. No. 9202MCM101(1707) For 4511 devices from ser. no: 4511 MODBUS RTU Configuration Manual Pulse isolator No. 9202MCM101(1707) For 4511 devices from ser. no: 141590001 9202 CONTENTS Introduction...3 Modbus basics...3 Modbus RTU...3 4511 Supported Modbus Function

More information

HC900 Controller Redundancy Overview & System Operation

HC900 Controller Redundancy Overview & System Operation HC900 Controller Redundancy Overview & System Operation Doc. No.: 51-52-25-133 Revision: 4 Date: Honeywell Process Solutions Notices and Trademarks Copyright 2006 by Honeywell Revision 4 Warranty/Remedy

More information

Setting the DCM Switches

Setting the DCM Switches 20 The device(s) connected to the DCM will help you determine the appropriate switch settings. Host Computer or Operator Interface Connection If you re using a host computer or operator interface as the

More information

P3-SCM. General Specifications

P3-SCM. General Specifications General Specifications Module Type Modules per Base Modules per Group I/O Points Used Field Wiring Connector Operating Temperature Storage Temperature Humidity Environmental Air Vibration Shock Field to

More information

DUCM Hardware. Niobrara Research & Development Corporation P.O. Box 3418 Joplin, MO USA

DUCM Hardware. Niobrara Research & Development Corporation P.O. Box 3418 Joplin, MO USA DUCM Hardware Manual DUCM Hardware Installation Manual This manual covers the DUCM hardware features and installation procedures. Effective: May 29, 2015 Niobrara Research & Development Corporation P.O.

More information

R1M-GH THERMOCOUPLE & DC INPUT MODULE MODEL. Remote I/O R1M Series. (16 points)

R1M-GH THERMOCOUPLE & DC INPUT MODULE MODEL. Remote I/O R1M Series. (16 points) Remote I/O R1M Series THERMOCOUPLE & DC INPUT MODULE (16 points) MODEL MODEL & SUFFIX CODE SELECTION R1MGH2T MODEL Modbus protocol I/O TYPE GH2 : Thermocouple or DC input, 16 points FIELD TERMINAL TYPE

More information

Installation and Programming Manual. Niobrara Research & Development Corporation P.O. Box 3418 Joplin, MO USA

Installation and Programming Manual. Niobrara Research & Development Corporation P.O. Box 3418 Joplin, MO USA DUCM DF1 Manual DUCM DF1 Installation and Programming Manual This manual describes the DUCM application for interfacing DF1 slaves to a Modbus or RNIM serial network. Effective: February 16, 2017 Niobrara

More information

HRM-0800 Instruction Manual

HRM-0800 Instruction Manual HRM-0800 Instruction Manual Table of Contents 1 Highway Addressable Remote Transducer (HART ) 4 2 General Specifications 5 3 Dimensions: 6 4 General Description 7 4.1 Introduction 7 4.2 Purpose 8 4.3 Functions

More information

Control Techniques Variable-Speed Drive (VSD) Interface to E2 v and Above

Control Techniques Variable-Speed Drive (VSD) Interface to E2 v and Above TECHNICAL BULLETIN Part #: 026-4122 Revision 0 Date: 2/5/2007 Control Techniques Variable-Speed Drive (VSD) Interface to E2 v. 2.40 and Overview Beginning with version 2.40, the E2 RX, BX, and CX series

More information

1. FEATURES AND BENEFITS

1. FEATURES AND BENEFITS Series S i x Programmable Controller GFK-0238A Communications Control Module Type 2 and Type 3 November 1988 IC600CB536 IC600CB537 General Description The Communications Control Module Type 2 (CCM2) and

More information

GW-7238D J1939 to Modbus TCP Server / RTU Slave Gateway

GW-7238D J1939 to Modbus TCP Server / RTU Slave Gateway GW-7238D J1939 to Modbus TCP Server / RTU Slave Gateway User s Manual www.icpdas.com 1 Warranty All products manufactured by ICP DAS are under warranty regarding defective materials for a period of one

More information

How to configure DeviceNet with Anybus NetTool for DeviceNet.

How to configure DeviceNet with Anybus NetTool for DeviceNet. How to configure DeviceNet with Anybus NetTool for DeviceNet. HMS Industrial Networks AB Page 1 (12) History Revision Date Description Responsible 1.00 2006-09-15 Released Thorbjörn Palm 1.01 2006-11-17

More information

How-To. Modbus-TCP communication between CelciuX and NJ. History

How-To. Modbus-TCP communication between CelciuX and NJ. History History Date Version Author Description 03.10.12 1.0 pk 1 st release 04.10.12 1.1 pk Added very important notes (tips and tricks) 22.11.12 1.2 pk Minor corrections according Thomas Grootenboers HowTo_ModbusTCP_CelciuX_NJ.docx

More information

HC900 Controller Redundancy Overview & System Operation

HC900 Controller Redundancy Overview & System Operation HC900 Controller Redundancy Overview & System Operation Doc. No.: 51-52-25-133 Revision: 6 Date: Honeywell Process Solutions Notices and Trademarks Copyright 2015 by Honeywell Revision 6, Warranty/Remedy

More information

MODEL: GR8-EM. Communication Adaptor GR8 Series

MODEL: GR8-EM. Communication Adaptor GR8 Series Communication Adaptor GR8 Series Ethernet/RS-485 Adaptor (Modbus use) Functions & Features Bidirectional protocol converter for Modbus/TCP (Ethernet) and Modbus RTU (RS-485) Fast response time thanks to

More information

IntesisBox Modbus Server KNX

IntesisBox Modbus Server KNX IntesisBox Modbus Server KNX User Manual r1.0 eng Issue date: 09/2017 Intesis Software S.L.U. 2017 All Rights Reserved. Information in this document is subject to change without notice. The software described

More information

T1K MODBUS Base Controller Specifications

T1K MODBUS Base Controller Specifications Base Controller 1 2 In This Chapter.... Base Controller Setting the DIP Switches Setting the Rotary Address Switches Port Pin out and Wiring RJ12 Serial Port Pin out and Wiring 2 2 Base Controller General

More information

IntesisBox Modbus Server M-Bus

IntesisBox Modbus Server M-Bus IntesisBox Modbus Server M-Bus User Manual r1.1 eng Issue date: 10/2017 Intesis Software S.L.U. 2017 All Rights Reserved. Information in this document is subject to change without notice. The software

More information

MODBUS RTU MODULE INSTRUCTIONS. for use with WSIQ2/WSE

MODBUS RTU MODULE INSTRUCTIONS. for use with WSIQ2/WSE INSTRUCTIONS MODBUS RTU MODULE for use with WSIQ2/WSE WorldWide Electric Corporation Phone: 1-8-88-2131 Fax: 1-8-711-1616 www.worldwideelectric.net Product Compatibility This communications module is suitable

More information

XL200 Series PLC Interface

XL200 Series PLC Interface Copyright 2010 AMS Controls, Inc. All rights reserved. The information contained in this document is proprietary to AMS Controls, Inc., and is not to be reproduced in any form without the specific written

More information

MODBUS-IN. Modbus Card. User & Installation Manual Xtreme Power Conversion Corporation. All rights reserved.

MODBUS-IN. Modbus Card. User & Installation Manual Xtreme Power Conversion Corporation. All rights reserved. MODBUS-IN User & Installation Manual www.xpcc.com 2014. All rights reserved. (Rev 12/17/14) Thank you for purchasing. This manual contains instructions and warnings that should be followed during the installation,

More information

TRAINING GUIDE LEVEL 3 MODBUS WRITE IMPORT COMMAND

TRAINING GUIDE LEVEL 3 MODBUS WRITE IMPORT COMMAND OleumTechTM TRAINING GUIDE LEVEL 3 MODBUS WRITE IMPORT COMMAND MUST BE FAMILIAR WITH LEVEL 1 TRAINING MATERIALS BEFORE MOVING FORWARD Doc ID# 80-6010-001b TABLE OF CONTENTS 1. WHAT IS NEW WRITE IMPORT

More information

VPGate Manual PROFIBUS to serial

VPGate Manual PROFIBUS to serial VPGate Manual PROFIBUS to serial Important information Purpose of the Manual This user manual provides information how to work with the VPGate PROFIBUS to serial. Document Updates You can obtain constantly

More information

A36D/TPSD DNP 3.0 & Modbus SCADA INTERFACE

A36D/TPSD DNP 3.0 & Modbus SCADA INTERFACE SCADA INTERFACE INSTRUCTIONS - OPTION 21P / 21Q - FOR A36D/TPSD SYSTEMS A36D/TPSD DNP 3.0 & Modbus SCADA INTERFACE OPTION 21P / 21Q INSTRUCTIONS This manual is only valid for A36D/TPSD Chargers equipped

More information

Chapter 1. Introduction. Additional Documentation

Chapter 1. Introduction. Additional Documentation Chapter 1 Introduction This chapter is an introduction to the PACSystems RX3i Serial Communications modules: Introduction to PACSystems RX3i Serial Communications Modules Introduction to Installing Serial

More information

DTBR-E Ethernet Communication. Distributor. User s Manual

DTBR-E Ethernet Communication. Distributor. User s Manual DTBR-E Ethernet Communication Distributor User s Manual FATEK AUTOMATION CORP. 3/13/2002 Ver. 1.2 1. Preface...2 2. Specification...3 2.1 Communication Distributor...3 2.2 Ethernet Serial Interface...3

More information

SmartLink Configuration Manual

SmartLink Configuration Manual SmartLink Configuration Manual October 2012 Part No. 4417554 Revision 2 Enraf B.V. P.O. Box 812 2600 AV Delft Netherlands Tel. : +31 15 2701 100 Fax : +31 15 2701 111 E-mail : enraf-nl@honeywell.com Website

More information

TABLE OF CONTENTS. Communication Functions

TABLE OF CONTENTS. Communication Functions TABLE OF CONTENTS Chapter 1: Chapter 2: Chapter 3: Chapter 4: General Features....................................................... 1-1 Functions......................................................

More information

Z-2400-RB/TCP TURBO Wireless Data Links Using ZIGBEE For MicroScan Protocols.

Z-2400-RB/TCP TURBO Wireless Data Links Using ZIGBEE For MicroScan Protocols. Z-2400-RB/TCP TURBO Wireless Data Links Using ZIGBEE For MicroScan Protocols. Installation Guide. Z-2400-Base/Remote Turbo Installation Guide Index: Description. Page 3 Ordering Information. Page 3 Specifications.

More information

ICP PANEL-TEC PEX3000 II

ICP PANEL-TEC PEX3000 II ICP PANEL-TEC PEX3000 II MODBUS PORT EXPANDER INSTALLATION AND OPERATION GUIDE REVISION HISTORY Revision Date Author Comments 000 29 Aug 2008 Keira Majors Initial release. 001 16 Sep 2008 David Walker

More information

D0 DCM Module Setup Direct

D0 DCM Module Setup Direct D0 DCM Module Setup 3 In This Chapter.... Important Module Information Using DirectSOFT5 to Configure s 1 and Port 2 Registers Using Ladder Logic to Configure s (DL05) Using Ladder Logic to Configure s

More information

Honeywell HC-900 with Acromag 967EN Modbus/TCP Module as Remote I/O

Honeywell HC-900 with Acromag 967EN Modbus/TCP Module as Remote I/O Acromag, Incorporated 30765 S Wixom Rd, PO Box 437, Wixom, MI 48393-7037 USA Tel: 248-295-0880 Fax: 248-624-9234 www.acromag.com Honeywell HC-900 with Acromag 967EN Modbus/TCP Module as Remote I/O Contents:

More information

TORRIX RS485. Technical Documentation. with MODBUS Protocol. Edition: Version: 2 Art. no.:

TORRIX RS485. Technical Documentation. with MODBUS Protocol. Edition: Version: 2 Art. no.: Technical Documentation TORRIX RS485 with MODBUS Protocol Edition: 2016-05 Version: 2 Art. no.: 350187 FAFNIR GmbH Schnackenburgallee 149 c 22525 Hamburg Tel.: +49 / 40 / 39 82 07 0 Fax: +49 / 40 / 390

More information

General Specifications. P2-SCM Serial Communications

General Specifications. P2-SCM Serial Communications General Specifications Module Type Intelligent Modules per Base I/O Points Used Field Wiring Connector Operating Temperature Storage Temperature Humidity Environmental Air Vibration Shock Field to Logic

More information

ZBRN2 Modbus Serial Line Communication

ZBRN2 Modbus Serial Line Communication Harmony XB5R Modbus Serial Line Communication EIO0000001177 03/2013 ZBRN2 Modbus Serial Line Communication 3 Purpose This chapter provides an overview of the Modbus layout description, communication and

More information

Industrial-Automation System HIMatrix. MODBUS Master/Slave. Manual

Industrial-Automation System HIMatrix. MODBUS Master/Slave. Manual Industrial-Automation System HIMatrix MODBUS Master/Slave Manual HIMA Paul Hildebrandt GmbH + Co KG Rev. 0.02 Industrial Automation HI 800 003 HEA Important Notes All HIMA products mentioned in this manual

More information

isma-b-mg-ip User Manual Global Control 5 Sp. z o.o. Poland, Warsaw

isma-b-mg-ip User Manual Global Control 5 Sp. z o.o. Poland, Warsaw isma-b-mg-ip User Manual Global Control 5 Sp. z o.o. Poland, Warsaw www.gc5.pl Table of content 1 Introduction... 4 1.1 Revision history... 5 1.2 Safety rules... 5 1.3 Technical specifications... 6 1.4

More information

CAS Barrington LanSTAR to BACnet-IP

CAS Barrington LanSTAR to BACnet-IP CAS-2700-54 Barrington LanSTAR to BACnet-IP Description The CAS-2700-54 Gateway translates data between a Barrington LanSTAR and BACnet-IP. The gateway connects to a Barrington LanSTAR through RS232. It

More information

Mitsubishi FX3 Driver Configuration Manual

Mitsubishi FX3 Driver Configuration Manual Driver Configuration Manual Version 7.0 rev 0a Advantech Corp., Ltd. page 1 Table of Contents Driver Configuration Manual 1 1. Configuration 2 1.1... 2 1.2 Module Settings... 2 2. WebAccess Configuration

More information

VersaMax* Serial Communications Module

VersaMax* Serial Communications Module Product The VersaMax Serial Communications Module, IC200CMM020, operates as a Modbus RTU Master in a VersaMax I/O Station controlled by a Genius Network Interface Unit or a PROFINET Scanner. Revision Firmware

More information

PMEUCM Hardware. Niobrara Research & Development Corporation P.O. Box 3418 Joplin, MO USA

PMEUCM Hardware. Niobrara Research & Development Corporation P.O. Box 3418 Joplin, MO USA PMEUCM Hardware Manual PMEUCM Hardware Installation Manual This manual covers the PMEUCM hardware features and installation procedures. Effective: August 10, 2017 Niobrara Research & Development Corporation

More information

D-100 FLOW DISPLAY MODBUS Network Interface Installation Guide

D-100 FLOW DISPLAY MODBUS Network Interface Installation Guide MODBUS D-100 FLOW DISPLAY MODBUS Network Interface Installation Guide 11451 Belcher Road South, Largo, FL 33773 USA Tel +1 (727) 447-6140 Fax +1 (727) 442-5699 www.onicon.com sales@onicon.com 03-18 0657-9

More information

The RS-485 user manual for B800 series communication

The RS-485 user manual for B800 series communication The user manual of B800 Series Rs-485 The RS-485 user manual for B800 series RS-232 inbuilt inside the main board of B800 series frequency inverter, we can effect RS-485 through fitting board externally.

More information

USER MANUAL. VA-1USB-T USB Transmitter. VA-1USB-R USB Receiver MODELS: P/N: Rev 3

USER MANUAL. VA-1USB-T USB Transmitter. VA-1USB-R USB Receiver MODELS: P/N: Rev 3 KRAMER ELECTRONICS LTD. USER MANUAL MODELS: VA-1USB-T USB Transmitter VA-1USB-R USB Receiver P/N: 2900-300209 Rev 3 Contents 1 Introduction 1 2 Getting Started 2 2.1 Achieving the Best Performance 2 2.2

More information

ModbusLink M ModbusLink S. Operations & Maintenance Manual

ModbusLink M ModbusLink S. Operations & Maintenance Manual ModbusLink M ModbusLink S Operations & Maintenance Manual Part No. 8800-1197 Revision 1.1 May 6, 2015 Sutron Corporation ModbusLink M & ModbusLink S Rev. 1.1 Operations & Maintenance Manual 5/11/2015 pg.

More information

Using Yaskawa CM049 BACnet Option with Delta Controls DSM-RTR

Using Yaskawa CM049 BACnet Option with Delta Controls DSM-RTR Using Yaskawa CM049 BACnet Option with Delta Controls DSM-RTR 1. INTRODUCTION: The following information describes utilizing the Yaskawa E7U and P7U Variable Frequency Drives with Yaskawa s CM049 BACnet

More information

1. Introduction. 2. Installation MODBUS INTERFACE

1. Introduction. 2. Installation MODBUS INTERFACE 5551.C 8473.C MODBUS INTERFACE PIM-MB-1 Modbus Interface 1. Introduction AuCom soft starters can be controlled and monitored across an RS485 serial communication network using the Modbus RTU and AP ASCII

More information

INTRINSICALLY SAFE DUPLEXER PROTECTION. ELECTRONICS, INC Vulcan Road Apopka, Florida MOTOR INSTRUCTION MANUAL

INTRINSICALLY SAFE DUPLEXER PROTECTION. ELECTRONICS, INC Vulcan Road Apopka, Florida MOTOR INSTRUCTION MANUAL INTRINSICALLY SAFE DUPLEXER INSTRUCTION MANUAL MOTOR PROTECTION ELECTRONICS, INC. 2464 Vulcan Road Apopka, Florida 32703 Phone: Website: (407) 299-3825 www.mpelectronics.com Operating Program Revision:

More information

Modbus Installation and Troubleshooting for AP9635/AP9635CH Network Management Card By Gary Ware. Introduction

Modbus Installation and Troubleshooting for AP9635/AP9635CH Network Management Card By Gary Ware. Introduction [ APPLICATION NOTE #168 ] APPLICATION NOTE #xx Modbus Installation and Troubleshooting for AP9635/AP9635CH By Gary Ware PROJECT AT A GLANCE Project Type Modbus installation Applications Data centers with

More information

Installation and Programming Manual

Installation and Programming Manual PMN Manual PMN Installation and Programming Manual This Manual describes the PMN PowerLogic Modbus Plus Network module, its uses and set up. Effective: 12 August, 1999 Niobrara Research & Development Corporation

More information

Wireless Transducer MOTOR PROTECTION ELECTRONICS, INC. INSTRUCTION MANUAL. (407) Phone: Website:

Wireless Transducer MOTOR PROTECTION ELECTRONICS, INC. INSTRUCTION MANUAL. (407) Phone: Website: Wireless Transducer INSTRUCTION MANUAL MOTOR PROTECTION ELECTRONICS, INC. 2464 Vulcan Road Apopka, Florida 32703 Phone: Website: (407) 299-3825 www.mpelectronics.com Operating Program Revision: 2 Revision

More information

RS232/RS485/RS422 to TCP/IP Converter ITEM NO.: RS007

RS232/RS485/RS422 to TCP/IP Converter ITEM NO.: RS007 RS232/RS485/RS422 to TCP/IP Converter ITEM NO.: RS007 RS007 is a universal data converter which support serial RS232, RS422 and RS485 to the TCP / IP intelligent communication converter, it offers RS485/RS422

More information

USER MANUAL FOR FIOA-0402-U-16

USER MANUAL FOR FIOA-0402-U-16 USER MANUAL FOR FIOA-0402-U-16 COPYRIGHT NOTICE This manual is a publication of Renu Electronics Pvt. Ltd. and is provided for use by its customers only. The contents of the manual are copyrighted by Renu

More information

INSTALLATION GUIDE Maxiflex P3e CPU M1262F

INSTALLATION GUIDE Maxiflex P3e CPU M1262F INSTALLATION GUIDE Maxiflex P3e CPU M1262F Introduction This Installation Guide is intended to aid the fitment of the M1262B CPU in the field. For operating details of this product, refer to the Users

More information

Bristol Babcock BSAP Serial & UDP Communications Drivers

Bristol Babcock BSAP Serial & UDP Communications Drivers Bristol Babcock BSAP Serial & UDP Communications Drivers Information Sheet for Crimson v3.0+ Compatible Devices Bristol Babcock Control Wave Micro controllers using BSAP communications. Verified Device

More information

PowerXL PC Tools Eaton Corporation. All rights reserved.

PowerXL PC Tools Eaton Corporation. All rights reserved. PowerXL PC Tools 101 2012 Eaton Corporation. All rights reserved. Agenda Power Xpert InControl Overview Connecting Parameter Editing Power Xpert InControl Firmware Upgrade Tool Overview Configuring Loading

More information

MGate MB3000 Modbus Gateway User Manual

MGate MB3000 Modbus Gateway User Manual MGate MB3000 Modbus Gateway User Manual Sixth Edition, July 2012 www.moxa.com/product 2012 Moxa Inc. All rights reserved. MGate MB3000 Modbus Gateway User s Manual The software described in this manual

More information

APPLICATION NOTE #xx. Modbus Installation and Troubleshooting for AP9635/AP9635CH Network Management Card By Gary Ware.

APPLICATION NOTE #xx. Modbus Installation and Troubleshooting for AP9635/AP9635CH Network Management Card By Gary Ware. [ APPLICATION NOTE #168 ] APPLICATION NOTE #xx Modbus Installation and Troubleshooting for AP9635/AP9635CH By Gary Ware PROJECT AT A GLANCE Project Type Modbus installation Applications Data centers with

More information

MGate MB3000 Modbus Gateway User s Manual

MGate MB3000 Modbus Gateway User s Manual User s Manual Seventh Edition, May 2013 www.moxa.com/product 2013 Moxa Inc. All rights reserved. User s Manual The software described in this manual is furnished under a license agreement and may be used

More information

Additional instructions Memograph M, RSG45 Advanced Data Manager

Additional instructions Memograph M, RSG45 Advanced Data Manager BA01390R/09/EN/02.15 71310077 Firmware ENU000A, V2.00.06 Products Solutions Services Additional instructions Memograph M, RSG45 Advanced Data Manager Modbus RTU/TCP Master Contents: 1 General information...

More information

Copyright: December 2017 Nidec Issue: E

Copyright: December 2017 Nidec Issue: E General Information The manufacturer accepts no liability for any consequences resulting from inappropriate, negligent or incorrect installation or adjustment of the optional parameters of the equipment

More information

MXM-50. Modbus Interface for Mitsubishi Air-Conditioning. Installation and User Guide.

MXM-50. Modbus Interface for Mitsubishi Air-Conditioning. Installation and User Guide. MXM-50 Modbus Interface for Mitsubishi Air-Conditioning Installation and User Guide www.innon.co.uk 1. Product Overview The Black Pear MXM-50 unit allows a Modbus building management system (BMS) to monitor

More information

Installation and Setup

Installation and Setup Installation and Setup 1 In This Chapter Installing the H PBC The Profibus Network Configuring the Controller Installing the H PBC Setting the Node Address Setting the Node Address Profibus DP is usually

More information

HART/ Modbus TCP Gateway GT200-HT-MT User Manual V 1.2 REV A SST Automation

HART/ Modbus TCP Gateway GT200-HT-MT User Manual V 1.2 REV A SST Automation HART/ Modbus TCP Gateway GT200-HT-MT User Manual V 1.2 REV A SST Automation E-mail: SUPPORT@SSTCOMM.COM WWW.SSTCOMM.COM Catalog 1 Product Overview... 4 1.1 Product Function...4 1.2 Product Features...

More information

InLinK HM Setup Software Installation & Operation Manual

InLinK HM Setup Software Installation & Operation Manual InLinK HM HART Protocol Modem Module with HART Device to Modbus Accumulator for OEM Applications 101-0014 Setup Software Installation & Operation Manual InLink-HM 101-0014 is a complete OEM HART protocol

More information

ICS Regent. Communications Package for W INTERPRET. Guarded Peer-Link Communications (T3831) PD-6041

ICS Regent. Communications Package for W INTERPRET. Guarded Peer-Link Communications (T3831) PD-6041 ICS Regent PD-6041 Communications Package for W INTERPRET Guarded Peer-Link Communications (T3831) Issue 1, March, 06 The WINTERPRET Communications Package is an add-in software package that allows you

More information

ETOR-4 Ethernet/Serial Gateway ETOR-4. Ethernet/Serial Gateway USER MANUAL

ETOR-4 Ethernet/Serial Gateway ETOR-4. Ethernet/Serial Gateway USER MANUAL ETOR-4 Ethernet/Serial Gateway USER MANUAL 1 TABLE OF CONTENTS SECTION 1 GENERAL INFORMATION...6 SECTION 2 INSTALLATION...9 2.1 Definitions on ETOR... 9 2.2 Configuring ETOR...10 2.3 Required Installations

More information

ISDA/ISDA4 Protocol Driver Manual. Table of Contents

ISDA/ISDA4 Protocol Driver Manual. Table of Contents ISDA/ISDA4 Protocol Driver Manual Table of Contents ISDA 1 Functional Overview... 3 1.1 Master Serial Port(s)... 3 1.2 Module Internal Database... 4 1.2.1 ISDA Serial Port Driver Access to Database...

More information

Operating Guide MODBUS (RTU) Communications Option IM/L150 MOD_2. Level Indicator L150 and L160

Operating Guide MODBUS (RTU) Communications Option IM/L150 MOD_2. Level Indicator L150 and L160 Operating Guide MODBUS (RTU) Communications Option IM/L150 MOD_2 Level Indicator L150 and L160 Electrical Safety This equipment complies with the requirements of CEI/IEC 61010-1:2001-2 "Safety requirements

More information

installation Operation ADDRESS product diagram H8030/8031 INSTALLATION GUIDE

installation Operation ADDRESS product diagram H8030/8031 INSTALLATION GUIDE POWER MONITORING INSTALLATION GUIDE H8030/8031 H8030/8031 Modbus Energy Meter Networked kw/kwh Transducer Product Identification Model Max Amps CT Size Enhanced Data Stream Meters H8030-0100- 100 H8030-0300-

More information

INSTRUCTION MANUAL STATION CONTROLLER SC1000 MOTOR PROTECTION ELECTRONICS, INC.

INSTRUCTION MANUAL STATION CONTROLLER SC1000 MOTOR PROTECTION ELECTRONICS, INC. INSTRUCTION MANUAL STATION CONTROLLER SC1000 MOTOR PROTECTION ELECTRONICS, INC. 2464 Vulcan Road, Apopka, Florida 32703 Phone: (407) 299-3825 Fax: (407) 294-9435 Revision Date: 9-11-08 Applications: Simplex,

More information

---- IntesisBox KNX Modbus RTU Master and Modbus TCP Client

---- IntesisBox KNX Modbus RTU Master and Modbus TCP Client ---- IntesisBox KNX Modbus RTU Master and Modbus TCP Client User Manual r1.1 eng Issue date: 05/2018 Intesis Software S.L.U. 2018 All Rights Reserved. Information in this document is subject to change

More information

System-10 BTU Meter BACnet Network Interface Installation Guide

System-10 BTU Meter BACnet Network Interface Installation Guide BACnet System-10 BTU Meter BACnet Network Interface Installation Guide 0652-3 1500 North Belcher Road, Clearwater, FL 33765 Tel (727) 447-6140 Fax (727) 442-5699 www.onicon.com sales@onicon.com 04-12 System-10-BAC

More information

RS485 IO Slim Module MOD-ETH

RS485 IO Slim Module MOD-ETH Expansion Module gateway Modbus TCP Version 1.0 01.12.2015 Manufactured for Thank you for choosing our product. This manual will help you with proper support and proper operation of the device. The information

More information

HART / EtherNet/IP Gateway GT200-HT-EI User Manual V 1.0 REV A SST Automation

HART / EtherNet/IP Gateway GT200-HT-EI User Manual V 1.0 REV A SST Automation HART / EtherNet/IP Gateway GT200-HT-EI V 1.0 REV A SST Automation E-mail: SUPPORT@SSTCOMM.COM WWW.SSTCOMM.COM Catalog 1 Product Overview... 4 1.1 Product Function...4 1.2 Product Features... 4 1.3 Technical

More information

GW-7228 J1939/Modbus RTU Slave Gateway

GW-7228 J1939/Modbus RTU Slave Gateway GW-7228 J1939/Modbus RTU Slave Gateway User s Manual www.icpdas.com GW-7228 J1939/Modbus RTU Slave Gateway User s Manual (Ver 1.2, May/2011) ------------- 1 Warranty All products manufactured by ICP DAS

More information

PROLOGIC Modular PLC CPU & I/O Modules Catalog and Design Guide

PROLOGIC Modular PLC CPU & I/O Modules Catalog and Design Guide PROLOGIC Modular PLC CPU & I/O Modules Catalog and Design Guide 23/03/2007 V0.1 Preliminary P.O.Box 24 Stanfield 3613 SOUTH AFRICA Tel: +27 (031) 7028033 Fax: +27 (031) 7028041 Email: proconel@proconel.com

More information

It is the installer's responsibility to follow all instructions in this manual and to follow correct electrical practice.

It is the installer's responsibility to follow all instructions in this manual and to follow correct electrical practice. MCD Modbus Module Instructions Important User Information INSTALLATION INSTRUCTIONS: MCD MODBUS MODULE Order Code: 175G9000 1. Important User Information Observe all necessary safety precautions when controlling

More information

Addendum to Verbatim Gateway Owner's Manual How to configure a Verbatim EtherNet/IP with RSLogix 5000

Addendum to Verbatim Gateway Owner's Manual How to configure a Verbatim EtherNet/IP with RSLogix 5000 Addendum to Verbatim Gateway Owner's Manual How to configure a Verbatim EtherNet/IP with RSLogix 5000 Addendum 1.1 Page 1 (25) Document history Revision Date Description Author 1.00 2003-04-16 Document

More information

Safety Instruction. This symbol indicates the possibility of injury or damage to property.

Safety Instruction. This symbol indicates the possibility of injury or damage to property. ig5a Ethernet Option Manual Safety Instruction To prevent injury and danger in advance for safe and correct use of the product, be sure to follow the Safety Instructions. The instructions are divided as

More information

CAS Veeder TCP - TLS 300, 350, 450. Gateway

CAS Veeder TCP - TLS 300, 350, 450. Gateway CAS-2700-03 Veeder TCP - TLS 300, 350, 450 Modbus (RTU and TCP) and BACnet and HTML Gateway Description The Veeder TCP Driver allows the Gateway to poll Veeder TLS Panel s for status, real time and configuration

More information

Wiring & Configuration for AE Solaron Inverters

Wiring & Configuration for AE Solaron Inverters DECK Monitoring LLC l 830 SW 10 th Ave, Ste #200 Portland, OR 97205 l www.deckmonitoring.com l 503.224.5546 Wiring & Configuration for AE Solaron Inverters Introduction It is the goal of this document

More information

iopro Distributed MODBUS-RTU IO Modules Product Manual

iopro Distributed MODBUS-RTU IO Modules Product Manual iopro Distributed MODBUS-RTU IO Modules Product Manual ioselect 3/15/2010 IOS-ioPro-Product-Manual-V07b.doc Disclaimer IoSelect Inc. makes no representations or warranties with respect to the contents

More information

Appendix G. CJ1W-CIF11 RS-422A Converter

Appendix G. CJ1W-CIF11 RS-422A Converter CJ1W-CIF11 RS-422A Converter The CJ1W-CIF11 RS-422A Converter connects directly to a CS/CJ-series RS-232C port and converts RS- 232C to RS-422A/485. Specifications General Specifications Item Specification

More information

H704-42(H)(E), H704-42/1(H)(E)

H704-42(H)(E), H704-42/1(H)(E) POWER MONITORING INSTALLATION GUIDE H704-42(H)(E), H704-42/1(H)(E) Branch Current Monitor DANGER NOTICE Installer's Specifications General: Operating Temp. Range 0 to 60 C (32 to 140 F) (

More information

PROGRAMMING INSTRUCTIONS

PROGRAMMING INSTRUCTIONS HOERBIGER Engine Solutions PROGRAMMING INSTRUCTIONS CPU-XL VARISPARK TERMINAL PROGRAM WARNING: WARNING: DEVIATION DEVIATION FROM THESE FROM INSTRUCTIONS THESE INSTRUCTIONS MAY LEAD MAY LEAD TO IMPROPER

More information

DNP 3.0 Serial (RS232/RS485) and Ethernet (TCP/IP) SCADA Interface for A31 Inverters with S2A-383S Option 21P. Setup Instructions

DNP 3.0 Serial (RS232/RS485) and Ethernet (TCP/IP) SCADA Interface for A31 Inverters with S2A-383S Option 21P. Setup Instructions La Marche Manufacturing Company www.lamarchemfg.com DNP 3.0 Serial (RS232/RS485) and Ethernet (TCP/IP) SCADA Interface for A31 Inverters with S2A-383S Option 21P Setup Instructions This manual is valid

More information

Motortronics VirtualSCADA VS2-MT Communication Gateway VS2-MT User Manual Revision

Motortronics VirtualSCADA VS2-MT Communication Gateway VS2-MT User Manual Revision Motortronics VirtualSCADA VS2-MT Communication Gateway VS2-MT User Manual Revision 1.03.00 Motortronics / Phasetronics 1600 Sunshine Drive Clearwater, Florida 33765 Tel: 727-573-1819 Fax: 727-573-1803

More information

Instructions. Modbus RTU Card (WSIQ-COM-MB)

Instructions. Modbus RTU Card (WSIQ-COM-MB) Instructions (WSIQ-COM-MB) Contents 1 Warnings... 2 2 Important User Information... 2 3 Installation... 2 4 Operation... 3 5... 4 6 Specifications... 15 Product Compatibility The is suitable for use with

More information

MODEL CIO-EN MODBUS/TCP, MODBUS/RTU I/O MODULE

MODEL CIO-EN MODBUS/TCP, MODBUS/RTU I/O MODULE INSTALLATION INSTRUCTIONS Revision B1 Rapid City, SD, USA, 05/2009 MODEL CIO-EN MODBUS/TCP, MODBUS/RTU I/O MODULE BE SURE POWER IS DISCONNECTED PRIOR TO INSTALLATION! FOLLOW NATIONAL, STATE AND LOCAL CODES.

More information

HC900 Control Station Model Numbers 900CS10-00 and 900CS15-00 Installation

HC900 Control Station Model Numbers 900CS10-00 and 900CS15-00 Installation HC900 Control Station Model Numbers 900CS10-00 and 900CS15-00 Installation Document Number: 51-52-33-157 Revision 8 Effective: 03/3/13 Supersedes: Revision 7, 09/8/11 Summary These instructions explain

More information

GE Fanuc Automation Programmable Control Products. PACSystems RX3i. Serial Communications Modules. User s Manual, GFK-2460A.

GE Fanuc Automation Programmable Control Products. PACSystems RX3i. Serial Communications Modules. User s Manual, GFK-2460A. GE Fanuc Automation Programmable Control Products PACSystems RX3i Serial Communications Modules User s Manual, GFK-2460A March 2007 Warnings, Cautions, and Notes as Used in this Publication GFL-002 Warning

More information