4(b): Assign the IP address on the Serial interface of Router. Console Cable

Size: px
Start display at page:

Download "4(b): Assign the IP address on the Serial interface of Router. Console Cable"

Transcription

1 Lab#4 Router Basic IOS 4(a). Router Basic Commands & Configuration 4(b) Assign the IP address on the Serial interface of Router Console Cable R1 PC1 Objectives Be familiar with use of different Configuration Modes in Router Configure router's identification (name). Configure a message of the day (motd) banner. Use the Interface Config Mode to enter a description for an interface. Use the Interface Configuration Mode to configure interfaces. Configure IP address assignments for router interfaces. Configure subnet mask assignments for router interfaces. Copy the running configuration to the backup configuration. Background In this lab you will use the router's Global configuration mode and enter oneline commands that will be used for Router Level Configuration. The router's prompt in global configuration mode is "Router-name(config)#". Other configuration modes will be used for multiple command lines and detailed configurations as in configuration of interfaces. When working with the interfaces, the router prompt looks like "Router-name(config-if)#". You will also configure a message-of-the-day banner using the banner motd command in global configuration mode and enter descriptions for the interfaces on the router in interface configuration mode.

2 Lab#4(a) Router Basic Commands & Configuration Objectives Be familiar with use of different Configuration Modes in Router Configure router's identification (name). Configure a message of the day (motd) banner. Use the Interface Config Mode to enter a description for an interface. Use the Interface Configuration Mode to configure interfaces. Configure IP address assignments for router interfaces. Configure subnet mask assignments for router interfaces. Copy the running configuration to the backup configuration. CCNA LAB MANUAL

3 Configuration Step 1 Connect and Login to the router Connect to the router using console cable. Open Hyper Terminal, select the COM port in the CONNECT TO window, Click OK, Click on Restore Defaults on the COMx Properties (where x is your COM port number), Click on OK and hit enter twice. You shall get the router prompt or prompt for the password. Enter the password cisco if prompted. CCNA LAB MANUAL

4 Step 2-Enter privileged mode from user mode You shall have this prompt when you login to the router Router> Enter enable (abbreviated "en") at the command prompt. Enter the password of current mode. You will get the prompt with # sign and it is privileged exec mode Router Con0 is now available Press RETURN to get started! User Access Verification Password Router> Router>en Password Router# Explanation You use the enable command to enter privileged EXEC mode. Step 3 - Show the active configuration file Enter show running-config (abbreviated "sh runn") at the router prompt. Router#sh runn Building configuration... Current configuration 974 bytes end Router# Explanation The router will display information on how it is currently configured from the file which is loaded in RAM (Random Access Memory).

5 Step 4 - Show the backup configuration file Enter show startup-config (abbreviated "sh start") at the router prompt. Router#sh startup Using 974 out of bytes Router# Explanation The router will display information on the backup configuration file stored in NVRAM (Non-Volatile RAM). Step 5 - Enter global configuration mode Enter configure terminal (abbreviated "config t") at the router prompt. Router#conf t Enter configuration commands, one per line. End with CNTL/Z. Router(config)# Explanation To configure the router you must enter the global configuration mode. Notice how the router prompt has change after this command. Step 6 - Enter the help command Enter the help command by typing (?) at the router prompt. Explanation The router will respond with all commands available in global configuration mode. Router1(config)#? Configure commands aaa Authentication, Authorization and Accounting. xot Global XOT commands Router(config)#

6 Step 7 - Enter the help command for hostname Enter help command for hostname by entering hostname? at the router prompt. Router(config)#hostname? WORD This system's network name Router(config)#hostname Explanation You can get help with any command by entering the command followed by a space and a (?). Step 8 - Change the hostname of the router Enter hostname and your routers name at the router prompt. Router1(config)#hostname R1 R1(config)# Explanation This command will change the router hostname to your provided name. Step 9 - Enter a message of the day Enter banner motd then write your message starting and ending with hash sign(#). It will be your Message Of The Day at the router prompt. R1(config)#banner motd # This is test MOTD # R1(config)# Explanation This command will create a Message of the day banner that will display when someone logs into the router. Note that the message is bracketed by # which tells the router the start and stop of the message. Step 10 - Show information about the active configuration file Enter exit at the router prompt to go one level back, but to go back to privileged exec mode from any level press CTRL+Z Enter show running-config at the router prompt. R1(config)#exit R1#

7 %SYS-5-CONFIG_I Configured from console by console R1#sh runn Building configuration... R1# Explanation To check the running configuration you first have to exit out of global configuration mode using exit, then you will be at a privilege mode prompt and can issue the show running-config command. Note The configuration change you just made is in effect until the router is rebooted or reloaded. If you want router to save these changes to Startup-Config file, that router use to load configuration each time it starts, use this command Copy running Startup-config Step 11 - Enter global configuration mode Enter configure terminal at the router prompt. R1#conf t Enter configuration commands, one per line. End with CNTL/Z. R1(config)# Explanation To configure the router you must enter the global configuration mode. Notice how the router prompt has change after this command. Step 12- Configure SSH Create a local user name R1(config)# username Ali password cisco Assign a domain name R1(config)# ip domain-name cisco.com This Command takes few a min to generate key R1(config)# crypto key generate rsa R1(config)# line vty 0 15 R1(config-line)# password cisco R1(config-line)# login local Configure vty ports for using SSH R1(config-line)# transport input telnet ssh

Lab 7 Configuring Basic Router Settings with IOS CLI

Lab 7 Configuring Basic Router Settings with IOS CLI Lab 7 Configuring Basic Router Settings with IOS CLI Objectives Part 1: Set Up the Topology and Initialize Devices Cable equipment to match the network topology. Initialize and restart the router and switch.

More information

Lab Using the CLI to Gather Network Device Information Topology

Lab Using the CLI to Gather Network Device Information Topology Topology Addressing Table Objectives Device Interface IP Address Subnet Mask Default Gateway R1 G0/1 192.168.1.1 255.255.255.0 N/A Lo0 209.165.200.225 255.255.255.224 N/A S1 VLAN 1 192.168.1.11 255.255.255.0

More information

PT Activity: Configure AAA Authentication on Cisco Routers

PT Activity: Configure AAA Authentication on Cisco Routers PT Activity: Configure AAA Authentication on Cisco Routers Instructor Version Topology Diagram Addressing Table Device Interface IP Address Subnet Mask R1 Fa0/0 192.168.1.1 255.255.255.0 S0/0/0 10.1.1.2

More information

Packet Tracer - Configuring Initial Switch Settings

Packet Tracer - Configuring Initial Switch Settings Topology Objectives Part 1: Verify the Default Switch Configuration Part 2: Configure a Basic Switch Configuration Part 3: Configure a MOTD Banner Part 4: Save Configuration Files to NVRAM Part 5: Configure

More information

Lab Securing Network Devices

Lab Securing Network Devices Topology Addressing Table Objectives Device Interface IP Address Subnet Mask Default Gateway R1 G0/1 192.168.1.1 255.255.255.0 N/A S1 VLAN 1 192.168.1.11 255.255.255.0 192.168.1.1 PC-A NIC 192.168.1.3

More information

Lab - Examining Telnet and SSH in Wireshark

Lab - Examining Telnet and SSH in Wireshark Topology Addressing Table Objectives Device Interface IP Address Subnet Mask Default Gateway R1 G0/1 192.168.1.1 255.255.255.0 N/A PC-A NIC 192.168.1.3 255.255.255.0 192.168.1.1 Part 1: Configure the Devices

More information

Cisco Network Academy CCNA 1 Introduction to Networks

Cisco Network Academy CCNA 1 Introduction to Networks Cisco Network Academy CCNA 1 Introduction to Networks Packet Tracer Practice with Dans Sample http://www.danscourses.com/ In this lab, you will learn how to configure the following tasks: IPv4 Addressing

More information

Lab Command Modes and Router Identification. Objective. Background/Preparation. Step 1 Login to the router in user EXEC mode

Lab Command Modes and Router Identification. Objective. Background/Preparation. Step 1 Login to the router in user EXEC mode Lab 3.1.2 Command Modes and Router Identification Objective Identify basic router modes of user EXEC and privileged EXEC. Use commands to enter specific modes. Become familiar with the router prompt for

More information

Lab Using the Boot System Command. Objective. Background/Preparation

Lab Using the Boot System Command. Objective. Background/Preparation Lab 5.1.3 Using the Boot System Command Objective Display information about the Cisco IOS Image (software) that is currently running. Determine where the IOS is booting from. Check the amount of RAM, Flash

More information

Lab Router Configuration Using Setup Instructor Version 2500

Lab Router Configuration Using Setup Instructor Version 2500 Lab 2.2.1 Router Configuration Using Setup Instructor Version 2500 Objective Use the System Configuration dialog (setup). Establish some basic router configurations. Background/Preparation A new router

More information

Command-Line Interface (CLI) Basics

Command-Line Interface (CLI) Basics 4 CHAPTER This chapter is intended as a quick reference, not as a step-by-step explanation of the Cisco IOS. The chapter describes basic Cisco IOS software command-line interfaces that you may need to

More information

Lab Configuring and Verifying Extended ACLs Topology

Lab Configuring and Verifying Extended ACLs Topology Topology 2015 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 1 of 8 Addressing Table Objectives Device Interface IP Address Subnet Mask Default Gateway R1 G0/1 192.168.10.1

More information

Lab Managing Router Configuration Files with Terminal Emulation Software

Lab Managing Router Configuration Files with Terminal Emulation Software Lab Managing Router Configuration Files with Terminal Emulation Software Topology Addressing Table Objectives Device Interface IP Address Subnet Mask Default Gateway R1 G0/1 192.168.1.1 255.255.255.0 N/A

More information

Lab Configuring Switch Security Features Topology

Lab Configuring Switch Security Features Topology Topology Addressing Table Objectives Device Interface IP Address Subnet Mask Default Gateway R1 G0/1 172.16.99.1 255.255.255.0 N/A S1 VLAN 99 172.16.99.11 255.255.255.0 172.16.99.1 PC-A NIC 172.16.99.3

More information

TELECOMMUNICATION MANAGEMENT AND NETWORKS

TELECOMMUNICATION MANAGEMENT AND NETWORKS QUAID-E-AWAM UNIVERSITY OF ENGINEERING SCIENCE AND TECHNOLOGY, NAWABSHAH TELECOMMUNICATION MANAGEMENT AND NETWORKS LAB # 3 CONFIGURING INTERFACES OF ROUTER AND SWITCH Topology Diagram Addressing Table

More information

KIM DONNERBORG / RTS. Cisco Lab Øvelse Af Kim Donnerborg / RTS. Side 0 af 8

KIM DONNERBORG / RTS. Cisco Lab Øvelse Af Kim Donnerborg / RTS. Side 0 af 8 KIM DONNERBORG / RTS Side 0 af 8 INDHOLDSFORTEGNELSE Lab: Basic Router Configuration... 2 Topology Diagram... 2 Addressing Table... 2 Learning Objectives... 2 Scenario... 2 Task 1: Cable the Network....

More information

Skills Assessment Student Training Exam

Skills Assessment Student Training Exam Skills Assessment Student Training Exam Time: 20 minutes Given an IP address and mask of (address / mask), design an IP addressing scheme that satisfies the following requirements. Network address/mask

More information

Lab Well-Known Port Numbers and Multiple Sessions

Lab Well-Known Port Numbers and Multiple Sessions Lab 10.2.5 Well-Known Port Numbers and Multiple Sessions Objective Enable HTTP services on a router. Show multiple HTTP and Telnet sessions on a single host. Observe well-known TCP port numbers on the

More information

Lab 3: Basic Device Configuration

Lab 3: Basic Device Configuration Lab 3: Basic Device Configuration University of Jordan Faculty of Engineering & Technology Computer Engineering Department Computer Networks Laboratory 907528 2 Lab 3: Basic Device Configuration **Given

More information

This document is exclusive property of Cisco Systems, Inc. Permission is granted to print and copy this document for non-commercial distribution and

This document is exclusive property of Cisco Systems, Inc. Permission is granted to print and copy this document for non-commercial distribution and This document is exclusive property of Cisco Systems, Inc. Permission is granted to print and copy this document for non-commercial distribution and exclusive use by instructors in the CCNA Exploration:

More information

Lab Establishing and Verifying a Telnet Connection Instructor Version 2500

Lab Establishing and Verifying a Telnet Connection Instructor Version 2500 Lab 4.2.2 Establishing and Verifying a Telnet Connection Instructor Version 2500 Objective Establish a Telnet connection to a remote router. Verify that the application layer between source and destination

More information

Chapter 5 Router and IOS Basics

Chapter 5 Router and IOS Basics Chapter 5 Router and IOS Basics Benefits of Routing Routers provide Packet filtering Connections between local networks Traffic control Wide area network (WAN) connections Routers operate at the Network

More information

First-Time Configuration

First-Time Configuration This chapter describes the actions to take before turning on your router for the first time Setup Mode, on page 1 Verifying the Cisco IOS Software Version, on page 4 Configuring the Hostname and Password,

More information

Using Cisco IOS XE Software

Using Cisco IOS XE Software This chapter describes the basics of using the Cisco IOS XE software and includes the following section: Accessing the CLI Using a Router Console, on page 1 Accessing the CLI Using a Router Console Before

More information

Lab 1. CLI Navigation. Scenario. Initial Configuration for R1

Lab 1. CLI Navigation. Scenario. Initial Configuration for R1 Lab 1 CLI Navigation This lab covers the most basic skills for accessing and using the command-line interface (CLI) on a Cisco router or switch. Many of the small, picky details of how the CLI works cannot

More information

Module 9, Assignment 7

Module 9, Assignment 7 Module 9, Assignment 7 7.2.3 Control Router via Console (in Packet Tracer) 1. Prepare a Cisco 1841 Router (see figure 6-9). 2. Prepare a PC for administration. 3. Prepare a console cable and plug the serial

More information

CISCO SWITCH BEST PRACTICES GUIDE

CISCO SWITCH BEST PRACTICES GUIDE CISCO SWITCH BEST PRACTICES GUIDE Table of Contents (After Clicking Link Hit HOME to Return to TOC) 1) Add Hostname... 2 2) Add Username and Password... 2 3) Create Secret Password... 2 4) Encrypt Password...

More information

Lab Configuring and Verifying Standard IPv4 ACLs Topology

Lab Configuring and Verifying Standard IPv4 ACLs Topology Topology 2016 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 1 of 10 Addressing Table Objectives Device Interface IP Address Subnet Mask Default Gateway R1 G0/1 192.168.10.1

More information

Lab Troubleshooting RIP

Lab Troubleshooting RIP Lab 7.2.6 Troubleshooting RIP Objective Set up an IP addressing scheme using class B networks. Configure RIP on routers. Observe routing activity using the debug ip rip command. Examine routes using the

More information

Chapter 10 Configure Clientless Remote Access SSL VPNs Using ASDM

Chapter 10 Configure Clientless Remote Access SSL VPNs Using ASDM Chapter 10 Configure Clientless Remote Access SSL VPNs Using ASDM This lab has been updated for use on NETLAB+ Topology Note: ISR G1 devices use FastEthernet interfaces instead of GigabitEthernet Interfaces.

More information

Skills Assessment Student Practice

Skills Assessment Student Practice Skills Assessment Student Practice Topology Assessment Objectives Part 1: Develop the IPv4 Address Scheme (15 points, 20 minutes) Part 2: Initialize and Reload Devices (10 points, 5 minutes) Part 3: Configure

More information

Chapter 10 Configure Clientless Remote Access SSL VPNs Using ASDM

Chapter 10 Configure Clientless Remote Access SSL VPNs Using ASDM Chapter 10 Configure Clientless Remote Access SSL VPNs Using ASDM Topology Note: ISR G1 devices use FastEthernet interfaces instead of GigabitEthernet Interfaces. 2016 Cisco and/or its affiliates. All

More information

ICND1. Switch Configuration Lab. All configurations have been set to factory defaults for these labs

ICND1. Switch Configuration Lab. All configurations have been set to factory defaults for these labs ICND1 Switch Configuration Lab TOPOLOGY 3xPC (hosts) 2x2950 (Layer 2 Switches) 1x3560 (Layer 3 Switch) 5x2811 (Routers, unused in this set of labs) All configurations have been set to factory defaults

More information

Lab Exploring Cisco IOS and Configuring Basic Switch Settings

Lab Exploring Cisco IOS and Configuring Basic Switch Settings Topology Addressing Table Objectives Device Interface IP Address Subnet Mask Default Gateway S1 VLAN 99 192.168.1.2 255.255.255.0 192.168.1.1 PC-A NIC 192.168.1.10 255.255.255.0 192.168.1.1 Part 1: Cable

More information

CCNA 1 Chapter 2 v5.0 Exam Answers %

CCNA 1 Chapter 2 v5.0 Exam Answers % CCNA 1 Chapter 2 v5.0 Exam Answers 2015 100% 1. Which two features are characteristics of flash memory? (Choose two.) Flash provides nonvolatile storage. Flash receives a copy of the IOS from RAM when

More information

Lab Configuring Router Passwords. Objective. Background/Preparation. Step 1 Login to the router in user EXEC mode

Lab Configuring Router Passwords. Objective. Background/Preparation. Step 1 Login to the router in user EXEC mode Lab 3.1.3 Configuring Router Passwords Objective Configure a password for console login to user EXEC mode. Configure a password for virtual terminal (Telnet) sessions. Configure a secret password for privileged

More information

Telnet, Console and AUX Port Passwords on Cisco Routers Configuration Example

Telnet, Console and AUX Port Passwords on Cisco Routers Configuration Example Telnet, Console and AUX Port Passwords on Cisco Routers Configuration Example Document ID: 45843 Contents Introduction Prerequisites Requirements Components Used Conventions Background Information Configure

More information

Chapter 10 Configure AnyConnect Remote Access SSL VPN Using ASDM

Chapter 10 Configure AnyConnect Remote Access SSL VPN Using ASDM Chapter 10 Configure AnyConnect Remote Access SSL VPN Using ASDM Topology Note: ISR G1 devices use FastEthernet interfaces instead of GigabitEthernet interfaces. 2015 Cisco and/or its affiliates. All rights

More information

Lab Configuring Basic RIPv2 (Solution)

Lab Configuring Basic RIPv2 (Solution) (Solution) Topology 2017 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 1 of 15 Addressing Table Objectives Device Interface IP Address Subnet Mask Default Gateway

More information

Lab Command Line Fundamentals Instructor Version 2500

Lab Command Line Fundamentals Instructor Version 2500 Lab 2.2.9 Command Line Fundamentals Instructor Version 2500 Objective Log into a router and go to the user and privileged modes. Use several basic router commands to determine how the router is configured.

More information

Before you start the lab exercises see the lab administrator or EEE3080F tutor to get assigned to your routers.

Before you start the lab exercises see the lab administrator or EEE3080F tutor to get assigned to your routers. EEE00F Lab Basics of the Network Lab Student Lab Manual Before you start the lab exercises see the lab administrator or EEE00F tutor to get assigned to your routers. Contents. Resources used in the labs...

More information

CCENT Study Guide. Chapter 6 Cisco s Internetworking Operating System (IOS)

CCENT Study Guide. Chapter 6 Cisco s Internetworking Operating System (IOS) CCENT Study Guide Chapter 6 Cisco s Internetworking Operating System (IOS) Chapter 6 Objectives The CCENT Topics Covered in this chapter include: 2.0 LAN Switching Technologies 2.3 Troubleshoot interface

More information

SEMESTER 2 Chapter 1 Planning and Cabling a Network V 4.0

SEMESTER 2 Chapter 1 Planning and Cabling a Network V 4.0 SEMESTER 2 Chapter 1 Planning and Cabling a Network V 4.0 135 points 1.1.1 What are the common components between a router and other computers? CPU RAM ROM Operating System 1.1.1.2 What does a router connect?

More information

Configuring Secure Shell (SSH)

Configuring Secure Shell (SSH) Prerequisites for Configuring Secure Shell, page 1 Restrictions for Configuring Secure Shell, page 2 Information About Configuring Secure Shell, page 2 How to Configure Secure Shell, page 4 Monitoring

More information

Lab - Configuring a Switch Management Address

Lab - Configuring a Switch Management Address Topology Addressing Table Objectives Device Interface IP Address Subnet Mask Default Gateway S1 VLAN 1 192.168.1.2 255.255.255.0 N/A PC-A NIC 192.168.1.10 255.255.255.0 N/A Part 1: Configure a Basic Network

More information

Retake - Skills Assessment Student Training (Answer Key)

Retake - Skills Assessment Student Training (Answer Key) Retake - Skills Assessment Student Training (Answer Key) Name:. Topology Assessment Objectives Part 1: Develop the IPv4 Address Scheme (15 points, 0 minutes) Part 2: Configure Device IPv4 and Security

More information

Lab Configuring and Verifying Standard IPv4 ACLs (Instructor Version Optional Lab)

Lab Configuring and Verifying Standard IPv4 ACLs (Instructor Version Optional Lab) (Instructor Version Optional Lab) Instructor Note: Red font color or gray highlights indicate text that appears in the instructor copy only. Optional activities are designed to enhance understanding and/or

More information

Lab Configuring Basic Router Settings with IOS CLI (Instructor Version Optional Lab)

Lab Configuring Basic Router Settings with IOS CLI (Instructor Version Optional Lab) (Instructor Version Optional Lab) Instructor Note: Red font color or gray highlights indicate text that appears in the instructor copy only. Optional activities are designed to enhance understanding and/or

More information

Troubleshooting Network analysis Software communication tests and development Education. Protocols used for communication (10 seconds capture)

Troubleshooting Network analysis Software communication tests and development Education. Protocols used for communication (10 seconds capture) Lab 1 Wireshark Wireshark is an open source and free packet analyser used for many purposes, such as: Troubleshooting Network analysis Software communication tests and development Education This reports

More information

CCNA Semester 2 labs. Labs for chapters 2 10

CCNA Semester 2 labs. Labs for chapters 2 10 CCNA Semester 2 labs Labs for chapters 2 10 2.2.2.5 Lab - Configuring IPv4 Static and Default Routes 2.3.2.4 Lab - Troubleshooting Static Routes 3.2.1.9 Lab - Configuring Basic RIPv2 5.2.2.9 Lab - Configuring

More information

King Fahd University of Petroleum & Minerals. Configuration of Routers and Establishing Routed Networks

King Fahd University of Petroleum & Minerals. Configuration of Routers and Establishing Routed Networks King Fahd University of Petroleum & Minerals Electrical Engineering Department EE 400, Experiment # 7 Objectives: Configuration of Routers and Establishing Routed Networks The objective of this experiment

More information

Lab 4.2.5a Connectivity Tests Ping

Lab 4.2.5a Connectivity Tests Ping Lab 4.2.5a Connectivity Tests Ping Objective Use the ping command to send ICMP datagrams to target host. Verify that the network layer between source and destination is working properly. Retrieve information

More information

CCNA 1 Chapter 2 v5.0 Exam Answers 2013

CCNA 1 Chapter 2 v5.0 Exam Answers 2013 CCNA 1 Chapter 2 v5.0 Exam Answers 2013 1. Refer to the exhibit. A switch was configured as shown. A ping to the default gateway was issued, but the ping was not successful. Other switches in the same

More information

config mode: Router> enable Router# configure terminal Enter configuration commands, one per line. End with CNTL/Z.

config mode: Router> enable Router# configure terminal Enter configuration commands, one per line. End with CNTL/Z. CCNA1-CH2 2.1.1.1 OS / IOS 2.1.2.1 console (serial) / ssh / telnet 2.1.2.2 putty (teraterm / mobxterm / ) 2.1.3.1 IOS operation: console (cable + config) in packettracer 2.1.3.2 user EXEC vs Privileged

More information

Lab Student Lab Orientation

Lab Student Lab Orientation Lab 1.1.1 Student Lab Orientation Objective In this lab, the students will complete the following tasks: Review the lab bundle equipment Understand the security pod topology Understand the pod naming and

More information

Lab Configure Basic AP Security through IOS CLI

Lab Configure Basic AP Security through IOS CLI Lab 8.3.1.2 Configure Basic AP Security through IOS CLI Estimated Time: 30 minutes Number of Team Members: Students will work in teams of two. Objective In this lab, the student will learn the following

More information

Lab Configuring Static Routes Instructor Version 2500

Lab Configuring Static Routes Instructor Version 2500 Lab 6.1.6 Configuring Static Routes Instructor Version 2500 Objective Configure static routes between routers to allow data transfer between routers without the use of dynamic routing protocols. Background/Preparation

More information

Lab Troubleshooting IP Address Issues Instructor Version 2500

Lab Troubleshooting IP Address Issues Instructor Version 2500 Lab 4.2.6 Troubleshooting IP Address Issues Instructor Version 2500 Objective Configure two routers and two workstations in a small WAN. Troubleshoot problems introduced by incorrect configurations. Background/Preparation

More information

Lab Troubleshooting Basic PPP with Authentication Topology

Lab Troubleshooting Basic PPP with Authentication Topology Topology 2013 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 1 of 8 Addressing Table Objectives Device Interface IP Address Subnet Mask Default Gateway R1 G0/1 192.168.1.1

More information

Console Port, Telnet, and SSH Handling

Console Port, Telnet, and SSH Handling Console Port Overview, on page 1 Connecting Console Cables, on page 1 Installing USB Device Drivers, on page 1 Console Port Handling Overview, on page 2 Telnet and SSH Overview, on page 2 Persistent Telnet,

More information

Lab - Configuring IPv6 Addresses on Network Devices

Lab - Configuring IPv6 Addresses on Network Devices Topology Addressing Table Device Interface IPv6 Address Prefix Length Default Gateway Objectives R1 G0/0 2001:DB8:ACAD:A::1 64 N/A G0/1 2001:DB8:ACAD:1::1 64 N/A S1 VLAN 1 2001:DB8:ACAD:1::B 64 N/A PC-A

More information

Configuring TACACS+ Finding Feature Information. Prerequisites for TACACS+

Configuring TACACS+ Finding Feature Information. Prerequisites for TACACS+ Finding Feature Information, page 1 Prerequisites for TACACS+, page 1 Information About TACACS+, page 3 How to Configure TACACS+, page 7 Monitoring TACACS+, page 16 Finding Feature Information Your software

More information

Chapter 11. Configuring and Testing Your Network

Chapter 11. Configuring and Testing Your Network Chapter 11 Configuring and Testing Your Network CCNA1-1 Chapter 11 Note for Instructors These presentations are the result of a collaboration among the instructors at St. Clair College in Windsor, Ontario.

More information

Hochschule Bremen Networking Lab

Hochschule Bremen Networking Lab Hochschule Bremen Networking Lab User Manual Welcome to the Hochschule Bremen networking lab. This manual will give you a brief introduction on how to use the PCs and networking hardware in the lab. The

More information

Send document comments to

Send document comments to CHAPTER 8 This chapter describes how to configure Telnet and includes the following topics: Information About the Telnet Server, page 8-1 Prerequisites for Telnet, page 8-1 Guidelines and Limitations,

More information

Using the Command-Line Interface

Using the Command-Line Interface CHAPTER 1 The Cisco Metro Ethernet (ME) 3400E Series Ethernet Access switch is supported by Cisco IOS software. This chapter describes how to use the switch command-line interface (CLI) to configure software

More information

Backup a copy of a router IOS from flash to a TFTP server. Reload the backup IOS software image from a TFTP server into flash on a router.

Backup a copy of a router IOS from flash to a TFTP server. Reload the backup IOS software image from a TFTP server into flash on a router. Lab 5.2.5 Managing IOS Images with TFTP Objective Backup a copy of a router IOS from flash to a TFTP server. Reload the backup IOS software image from a TFTP server into flash on a router. Background/Preparation

More information

This document is exclusive property of Cisco Systems, Inc. Permission is granted to print and copy this document for non-commercial distribution and

This document is exclusive property of Cisco Systems, Inc. Permission is granted to print and copy this document for non-commercial distribution and This document is exclusive property of Cisco Systems, Inc. Permission is granted to print and copy this document for non-commercial distribution and exclusive use by instructors in the CCNA 2: Routers

More information

Lab - Configuring Basic DHCPv4 on a Router (Solution)

Lab - Configuring Basic DHCPv4 on a Router (Solution) (Solution) Topology Addressing Table Objectives Device Interface IP Address Subnet Mask Default Gateway R1 G0/0 192.168.0.1 255.255.255.0 N/A G0/1 192.168.1.1 255.255.255.0 N/A S0/0/0 (DCE) 192.168.2.253

More information

Lab Configuring Dynamic and Static NAT (Solution)

Lab Configuring Dynamic and Static NAT (Solution) (Solution) Topology Addressing Table Objectives Device Interface IP Address Subnet Mask Default Gateway Gateway G0/1 192.168.1.1 255.255.255.0 N/A S0/0/1 209.165.201.18 255.255.255.252 N/A ISP S0/0/0 (DCE)

More information

CHAPTER 2 ACTIVITY

CHAPTER 2 ACTIVITY CHAPTER 2 ACTIVITY 2.1.1.1 1. CLI stands for 2. GUI stands for 3. Write the step you used to go to CLI interface on Windows 4. The OS, normally loads from a disk drive, into RAM. 5. The portion of the

More information

Lab - Building a Switch and Router Network

Lab - Building a Switch and Router Network Topology Addressing Table Device Interface IP Address Subnet Mask Default Gateway G0/0 192.168.0.1 N/A G0/1 192.168.1.1 N/A PC-A NIC 192.168.1.3 192.168.1.1 PC-B NIC 192.168.0.3 192.168.0.1 R1 Objectives

More information

Configuring Secure Shell

Configuring Secure Shell Configuring Secure Shell Last Updated: October 24, 2011 The Secure Shell (SSH) feature is an application and a protocol that provides a secure replacement to the Berkeley r-tools. The protocol secures

More information

Checklists for Configuring the Gateway

Checklists for Configuring the Gateway CHAPTER 7 The Cisco Unified Communications Manager Business Edition 3000 uses either Cisco 2901 Integrated Services Router (ISR2901) or Cisco Media Convergence Server 7890C1 (MCS7890-C1) to serve as your

More information

Lab Configuring Dynamic and Static NAT (Instructor Version Optional Lab)

Lab Configuring Dynamic and Static NAT (Instructor Version Optional Lab) (Instructor Version Optional Lab) Instructor Note: Red font color or gray highlights indicate text that appears in the instructor copy only. Optional activities are designed to enhance understanding and/or

More information

Lab VTY Restriction Instructor Version 2500

Lab VTY Restriction Instructor Version 2500 Lab 11.2.6 VTY Restriction Instructor Version 2500 NOTE: The loopback entry in this graphic is not required in the lab. Objective Scenario Use the access-class and line commands to control Telnet access

More information

~ 1 ~ Ankara University Department of Computer Engineering COM LAB 1 Part 1

~ 1 ~ Ankara University Department of Computer Engineering COM LAB 1 Part 1 ~ 1 ~ Ankara University Department of Computer Engineering COM332 2017 LAB 1 Part 1 SECTION 1 PC Network TCP/IP Configuration Objective Identify tools used to discover a computer network configuration

More information

Lab Capturing and Analyzing Network Traffic

Lab Capturing and Analyzing Network Traffic Lab 1.2.2 Capturing and Analyzing Network Traffic Host Name IP Address Fa0/0 Subnet Mask IP Address S0/0/0 Subnet Mask Default Gateway RouterA 172.17.0.1 255.255.0.0 192.168.1.1 (DCE) 255.255.255.0 N/A

More information

Lab Designing and Implementing a VLSM Addressing Scheme. Topology. Objectives. Background / Scenario

Lab Designing and Implementing a VLSM Addressing Scheme. Topology. Objectives. Background / Scenario CSNB214 Packet Tracer Lab Designing and Implementing a VLSM Addressing Scheme Topology Objectives Part 1: Examine Network Requirements Part 2: Design the VLSM Address Scheme Part 3: Cable and Configure

More information

Lab Verifying RIP v2 Configuration

Lab Verifying RIP v2 Configuration Lab 1.2.5 Verifying RIP v2 Configuration Objective Configure RIP v1 and v2 on routers. Use show commands to verify RIP v2 operation. Background/Preparation Cable a network similar to the one shown in the

More information

1. Which OSI layers offers reliable, connection-oriented data communication services?

1. Which OSI layers offers reliable, connection-oriented data communication services? CCNA 1 Practice Final Exam Answers v4.0 100% 1. Which OSI layers offers reliable, connection-oriented data communication services? application presentation session transport network 2. Refer to the exhibit.

More information

Packet Tracer - Configure Cisco Routers for Syslog, NTP, and SSH Operations (Instructor Version)

Packet Tracer - Configure Cisco Routers for Syslog, NTP, and SSH Operations (Instructor Version) Packet Tracer - Configure Cisco Routers for Syslog, NTP, and SSH Operations (Instructor Version) Instructor Note: Red font color or Gray highlights indicate text that appears in the instructor copy only.

More information

Chapter 8: Lab B: Configuring a Remote Access VPN Server and Client

Chapter 8: Lab B: Configuring a Remote Access VPN Server and Client Chapter 8: Lab B: Configuring a Remote Access VPN Server and Client Topology IP Addressing Table Device Interface IP Address Subnet Mask Default Gateway Switch Port R1 FA0/1 192.168.1.1 255.255.255.0 N/A

More information

Lab Managing IOS Images with TFTP Instructor Version 2500

Lab Managing IOS Images with TFTP Instructor Version 2500 Lab 5.2.5 Managing IOS Images with TFTP Instructor Version 2500 Objective Backup a copy of a router IOS from flash to a TFTP server. Reload the backup IOS software image from a TFTP server into flash on

More information

IOS and Configuration Basics

IOS and Configuration Basics APPENDIX C This appendix contains basic information about the Cisco Internet Operating System (IOS) software and includes the following sections: Cisco IOS Modes of Operation Getting Context-Sensitive

More information

Skills Assessment Student Training

Skills Assessment Student Training Skills Assessment Student Training Topology Assessment Objectives Part 1: Initialize Devices (6 points, 5 minutes) Part 2: Configure Device Basic Settings (33 points, 20 minutes) Part 3: Configure Switch

More information

Lab Configuring 802.1Q Trunk-Based Inter-VLAN Routing Topology

Lab Configuring 802.1Q Trunk-Based Inter-VLAN Routing Topology Topology 2016 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 1 of 7 Addressing Table Device Interface IP Address Subnet Mask Default Gateway R1 G0/1.1 192.168.1.1

More information

Secure Shell Version 2 Support

Secure Shell Version 2 Support Secure Shell Version 2 Support Last Updated: January 16, 2012 The Secure Shell Version 2 Support feature allows you to configure Secure Shell (SSH) Version 2. SSH runs on top of a reliable transport layer

More information

Lab Configuring IPv4 Static and Default Routes (Solution)

Lab Configuring IPv4 Static and Default Routes (Solution) (Solution) Topology Addressing Table Device Interface IP Address Subnet Mask Default Gateway R1 G0/1 192.168.0.1 255.255.255.0 N/A S0/0/1 10.1.1.1 255.255.255.252 N/A R3 G0/1 192.168.1.1 255.255.255.0

More information

Lab Configuring 802.1Q Trunk-Based Inter-VLAN Routing (Instructor Version Optional Lab)

Lab Configuring 802.1Q Trunk-Based Inter-VLAN Routing (Instructor Version Optional Lab) (Instructor Version Optional Lab) Instructor Note: Red font color or gray highlights indicate text that appears in the instructor copy only. Optional activities are designed to enhance understanding and/or

More information

Lab Configuring Per-Interface Inter-VLAN Routing (Solution)

Lab Configuring Per-Interface Inter-VLAN Routing (Solution) (Solution) Topology Addressing Table Objectives Device Interface IP Address Subnet Mask Default Gateway R1 G0/0 192.168.20.1 255.255.255.0 N/A G0/1 192.168.10.1 255.255.255.0 N/A S1 VLAN 10 192.168.10.11

More information

Chapter 6: Network Layer

Chapter 6: Network Layer Chapter 6: Network Layer Introduction to Networks Intro to Networks v5 Network Layer Intro to Networks v5 2 The Network Layer End to End Transport processes Addressing end devices Encapsulation of Packets

More information

Configuring Local Authentication

Configuring Local Authentication This chapter describes local authentication. This chapter also describes procedures to configure local authentication and privilege levels. This chapter includes the following topics: Understanding Authentication,

More information

Education by Simulation Stand Alone Labs For CCNA

Education by Simulation Stand Alone Labs For CCNA Education by Simulation Stand Alone Labs For CCNA Copyright 1998-2004 Boson Software, Inc. All Rights Reserved. No part of this copyrighted document or related copyrighted software may be reproduced, transmitted,

More information

Lab Configuring Per-Interface Inter-VLAN Routing (Instructor Version)

Lab Configuring Per-Interface Inter-VLAN Routing (Instructor Version) (Instructor Version) Instructor Note: Red font color or Gray highlights indicate text that appears in the instructor copy only. Topology Addressing Table Objectives Device Interface IP Address Subnet Mask

More information

Lab Backing up Configuration Files Instructor Version 2500

Lab Backing up Configuration Files Instructor Version 2500 Lab 3.2.9 Backing up Configuration Files Instructor Version 2500 Objective Demonstrate the capture of the running configuration of a router to an ASCII text file with HyperTerminal. Edit or modify the

More information

Lab AAA Authorization and Accounting

Lab AAA Authorization and Accounting Lab 11.3.2 AAA Authorization and Accounting Objective Scenario Step 1 In this lab, the student will use the exec-timeout command to control the amount of time before an idle telnet or console session is

More information

Cisco IOS Configuration Basics

Cisco IOS Configuration Basics Cisco IOS Configuration Basics Switching Router Overview Router configuration controls the operation of the router s: Interface IP address and netmask Routing information (static, dynamic or default) Boot

More information

CCNA 1 Chapter 11 V4.0 Answers

CCNA 1 Chapter 11 V4.0 Answers CCNA 1 Chapter 11 V4.0 Answers 1. Refer to the exhibit. What command will place the router into the correct mode to configure an appropriate interface to connect to a LAN? UBAMA# configure terminal UBAMA(config)#

More information

Lab : Challenge OSPF Configuration Lab. Topology Diagram. Addressing Table. Default Gateway. Device Interface IP Address Subnet Mask

Lab : Challenge OSPF Configuration Lab. Topology Diagram. Addressing Table. Default Gateway. Device Interface IP Address Subnet Mask Topology Diagram Addressing Table Device Interface IP Address Subnet Mask Default Gateway Fa0/0 HQ S0/0/0 S0/0/1 Lo1 10.10.10.1 255.255.255.252 Fa0/0 Branch1 S0/0/0 S0/0/1 Fa0/0 Branch2 S0/0/0 S0/0/1 PC1

More information