How to Install Patch 7

Size: px

Start display at page:

Download "How to Install Patch 7"

Lester Holland
6 years ago
Views:

1 How to Install Patch 7 ICP-MS MassHunter G7201B B How to Install Patch 7 for G7201B B Contents 1 Install Patch 7 for ICP-MS MassHunter G7201B B Confirm Build No Re-Configuring LC * Updating system parameter * *1 Required when instrument is integrated with LC and previous software is B Patch4 or older *2 Required when instrument type is 8800 and previous software is B Patch4 or older Page 1 of 11

1 Install Patch 7 for ICP-MS MassHunter G7201B B.01.03 1.1 Confirm UAC level setting of the Windows has been set to the lowest. 1.2 Launch MassHunter Instrument Control once and close it.

2 1 Install Patch 7 for ICP-MS MassHunter G7201B B Confirm UAC level setting of the Windows has been set to the lowest. 1.2 Launch MassHunter Instrument Control once and close it. 1.3 Extract Patch.msp from ZIP and double click it. 1.4 Click Next 1.5 Click Next Page 2 of 11

3 1.6 Click Update Page 3 of 11

4 1.7 Click Finish How to Install Patch 7 for G7201B B Page 4 of 11

2 Confirm Build No. 2.1.1 Launch Data Analysis Software. 2.1.2 Open help-about dialog box by [Help] [About] 2.1.3 If you can see the version, G7201B Version B.01.03 Build 393.

5 2 Confirm Build No Launch Data Analysis Software Open help-about dialog box by [Help] [About] If you can see the version, G7201B Version B Build Patch 7, then the patch is installed correctly. 3 Re-Configuring LC *1 *1 Required when instrument is integrated with LC and previous software is B Patch4 or older. If the Patch 7 has been overwritten on Patch 5 or newer, the operations below are not required. 3.1 Open instrument control window of MassHunter. 3.2 Set sample introduction type "Peripump" 3.3 Set sample introduction type "LC1200" and establish connection with LC. Page 5 of 11

4 Updating system parameter *2 *2 Required when instrument type is 8800 and previous software is B.01.03 Patch4 or older.

6 4 Updating system parameter *2 *2 Required when instrument type is 8800 and previous software is B Patch4 or older. If the Patch 7 has been overwritten on Patch 5 or newer, the operation s below are not required. 4.1 Save the script file "Update Inside-Inlet_Temp_Diff for Duct stop.icpms.script" to the following directory C:\Agilent\ICPMH\script\Acq (or D:\Agilent\ICPMH\script\Acq). The script file can be downloaded from the same location as the Patch Open the Instrument Control window of MassHunter. Confirm instrument is online. If not, make it online. Software will ask for uploading firmware. Then follow the instruction on the screen and let the MassHunter update the firmware. 4.3 If the status of the instrument is not shutdown mode, change the status to shutdown mode via >Hardware pane>main frame>right click >Vacuum Off. 4.4 Close and re-open ICP-MS Instrument Control. 4.5 On the Welcome Screen, click the Close button. NOTE: On the Welcome screen, do not click any button other than the Close button (you may disregard this if the Welcome Screen is not displayed). NOTE: From step 1.5 (restarting MassHunter) through step 1.11 (executing the script), users must not move to Hardware Task or Startup. Page 6 of 11

7 4.6 Click system menu (Top left icon) -> Show/Hide Script menu to show Script menu. Page 7 of 11

4.7 Confirm "Script menu" is displayed on main menu bar. Then Select "Script" -> "Run script" and run a script "Update Inside-Inlet Temp Diff for Duct stop.icpms.script". 4.

If the PCA P/N is G3280-65110 (manufacturing P/N G3280-61110 printed on PCA), it is old type, other than that, it is new type. The P/N is printed on the PCA, refer to section 4.

8 4.7 Confirm "Script menu" is displayed on main menu bar. Then Select "Script" -> "Run script" and run a script "Update Inside-Inlet Temp Diff for Duct stop.icpms.script". 4.8 Script will ask you the Introduction PCA type of the instrument. Then select "Old type" or "New Type". If the PCA P/N is G (manufacturing P/N G printed on PCA), it is old type, other than that, it is new type. The P/N is printed on the PCA, refer to section 4.9 following, for further information on the PCA part numbers and how to check. If the system parameter update procedure is done by an ICP-MS customer, the recommended procedure is to ask the Agilent FSE who is in charge of the customer's account for the P/N. Page 8 of 11

9 4.9 Loosen the 2 screws and remove the Left Side Access panel to view the introduction PCA. The part number is usually printed in the top right of the PCA. Page 9 of 11

Recent PCA (New Type) G3280-65110 G3280-65067 G8400-65801 Obsolete: when replacing, order G8400-65801 Obsolete: when replacing,

10 The below table indicates the part numbers manufacturing p/n will be printed on the PCA. Support P/N the orderable part number for the PCA (P/N on the sticker) NOTE Original PCA (Old Type) Recent PCA (New Type) Recent PCA (New Type) G G G Obsolete: when replacing, order G Obsolete: when replacing, order G Replaces G and G Confirmation message will appear, then click OK Close and re-open ICP-MS Instrument Control. Page 10 of 11

11 This information is subject to change without notice Agilent Technologies, Inc Published in Japan, 01-November-2016 Page 11 of 11

Agilent MassHunter Workstation Software Offline Qualitative and Quantitative Analysis

Agilent MassHunter Workstation Software Offline Qualitative and Quantitative Analysis Installation Guide Step 1. Remove Older Versions of MassHunter and Microsoft Excel Software 2 Step 2. Install Microsoft