SmartWorx Viva How to Record Static Observation Data On-Board GS Receivers Operating in Base Mode
|
|
- Buck Chambers
- 6 years ago
- Views:
Transcription
1 SmartWorx Viva How to Record Static Observation Data On-Board GS Receivers Operating in Base Mode Firmware Version 4.03 AUG12 The Viva system provides many options that improve on needed hardware in the field. One of these options is the ability to store static GNSS observations directly to a SD memory card in the GS receiver. There are options for storing either the Leica MDB format or RINEX formatted data files. Each of these options for recording static data requires a license key to activate these capabilities. This guide will provide the steps needed to start a static observation session with a single CS controller and a GS receiver operating as an RTK base. In this example the GS receiver that will be used as a RTK base has already been configured for transmitting the needed RTK corrections. The options shown here are required to configure the GS receiver to collect static data while operating in base mode. Inserting the SD Card into the GS Receiver The SD card that will store the GNSS observation should be placed in the GS receiver. The following Figures A and B show an example of the LED configuration for the GS receivers when a formatted SD card is inserted and ready to record data. When the SD card is inserted into the receiver the LED next to the SD card icon will turn solid green. This means the card is recognized and available for data recording. Figure A - Leica GS15 with SD Card Inserted 2012 G360, LLC All rights reserved
2 Figure B - Leica GS10 with SD Card Inserted Static Observation Recording Settings for a GS Receiver These are the needed settings for the GS RTK base to record static data: From the main menu select the Instrument icon Page 2
3 Next, choose the Base settings icon Next, select the Raw data settings icon Page 3
4 In the Logging GPS Base Data screen select the box next to Log data for post-processing and the options will be viewable. In the Rate: field choose the epoch interval you wish to record observations. In the Data type: field you can choose either Leica format (MDB) or RINEX if you have the needed options activated on the GS receiver. In this example we will be logging data in Leica format (MDB) to import the static data into Leica Geo Office (LGO) for processing. Leica Static Data (MDB) If you were logging RINEX format directly on the GS receiver, the options would appear as follows: RINEX ver 2.11 Page 4
5 Completing RTK Base Setup To start the RTK base with raw data logging, simply choose the Go to Work! icon from the main menu. Next choose the icon for the method of choosing the base coordinate. In this example we are setting up the receiver over a known point. For this options choose Over known point Page 5
6 You can now enter the Antenna Height, and RTK base antenna definition and then select F1 (Next) function key. No you are prompted to select the coordinates of the control point you have placed the RTK base receiver. Select the correct Point ID: and check your coordinates. Select F1 (Next) and the receiver will accept the coordinates and start to transmit RTK corrections and log static raw data. Page 6
7 Viva SmartWorx will know display the following message: This message gives the user the option to stay connected to the base receiver or to switch over to the rover receiver. If you are using a Bluetooth connection you can switch over to the Rover mode by selecting F1 (Rover). If you have your CS controller connected to the base receiver by the use of a GEV237 or a GEV234 cable, remove the cable connection first and then select F1 (Rover). Return to Rover Mode When you choose to switch to the rover mode the CS controller will disconnect from the GS base receiver. You will receive the message Connection to GS sensor lost when the system disconnects from the GS base receiver and the system will change to the Rover mode menu, Page 7
8 Check the GS Base Receiver for Static Data Logging Before you leave the GS Base receiver, observe that the SD card is recording the raw data. The LED for the SD card will blink green as shown in Figures C and D when the SD card is recording data. Figure C - Leica GS15 with SD Card Logging Data Figure D - Leica GS10 with SD Card Logging Data Please do not forget about the imaging capabilities of SmartWorx. Stop and take a picture(s) and assign it to you control point in the database Img_CONTROL PT 1_180112_ jpg Page 8
9 Saving the Static Survey Data File and Ending the Static Session When you have collected static data for the set time needed and you are ready to shut down the GS Base receiver simply turn off the GS receiver. There is no need to reconnect to the GS receiver with the CS controller. The file is closed and saved when the receiver is in the process of powering down from operation. Importing the GNSS Data in Leica Geo Office So, now you have completed your field work and are ready to process the static data in Leica Geo Office (LGO). The static data for the GS Base Receiver is on the SD card used in the GS Base Receiver. The GNSS raw data is located under the \DBX directory of the SD card used in the GS base receiver. Please note that there are no individual job folders kept on the SD card for the job you were working in while in the field. Each GNSS raw data file (.m00) will be named with the last four digits of the serial number of the GS unit, the data, and time of file creation. In the example shown the last four digits of the serial number for the GS receiver is 9685, the job was created on August 7, and was created at 5:21:43 pm. So the file name is 9685_0807_ m00 To complete the data download, please copy the (.m00) file from the SD card and place it on your local hard drive or network server Page 9
10 Next, create a project as you would normally in LGO. When you import the GNSS raw data into the LGO project for the static session observations you will need to highlight the name that for the (.m00) file from the base receiver. Once the raw data has been imported you can see that the point name, antennae setup, height, and code are all imported into the LGO project for the observed point. You can also right mouse-click on the Point ID and choose Properties to observe the information from the static session. Page 10
11 Point Properties in GPS Processing page If you have Technical Support questions, please contact us at G360.. Technical Support: Page 11
Product Leica Geo Office 8.2 Date October 26th, 2011
Product Leica Geo Office 8.2 Date October 26th, 2011 Leica Geosystems AG Heinrich-Wild-Strasse CH-9435 Heerbrugg Switzerland 1 About this Release LEICA GEO OFFICE VERSION 8.2 LEICA Geo Office (LGO) is
More informationUse of SmartRinex for Post Processed Kinematic Surveys
Use of SmartRinex for Post Processed Kinematic Surveys This guide is intended to provide the user with a method of working with a Leica SmartNet licence where real time corrections whether with GPRS, GSM
More informationLeica Viva TPS October 2010
Leica Viva TPS TS11/15 CS10/15 Summary Firmware is software that is embedded in a piece of hardware. More or less it is software for hardware. Leica regularly releases updated firmware to improve performance
More informationTcpGPS. User Manual. Installation. The steps below must be followed:
TcpGPS User Manual Installation The steps below must be followed: 1. Decompress the file TcpGPSSetup.zip. 2. Execute the file vcredist_x86_vs2008.exe. This application will install the libraries required
More informationLeica Captivate. Software Release Notes. Field Controllers: CS20, CS35 Total Stations: TS16, TS60, MS60, TS13 GNSS Sensors: GS18 T
Leica Captivate v4.10 Software Release Notes Product Leica Captivate Field Controllers: CS20, CS35 Total Stations: TS16, TS60, MS60, TS13 GNSS Sensors: GS18 T Release date 10 th December 2018 Maintenance
More informationLeica Captivate. Software Release Notes. Field Controllers: CS20, CS35 Total Stations: TS16, TS60, MS60. Release date 5 th March 2018
Leica Captivate v3.20 Software Release Notes Product Leica Captivate Field Controllers: CS20, CS35 Total Stations: TS16, TS60, MS60 Release date 5 th March 2018 Maintenance date 5 th March 2018 Available
More informationLeica Viva. Software Release Notes. Release Details: Version 2.10 Release date 25 May Available for: Products CS10, CS15, GS10, GS15, Viva Uno
Software Release Notes Release Details: Version 2.10 Release date 25 May 2010 Available for: Products CS10, CS15, GS10, GS15, Viva Uno Available via: DVD SmartWorx Viva (article number 767908) myworld
More informationLeica Viva GS14 Designed for Performance
Leica Viva GS14 Designed for Performance Your Vision: Flexibility and Performance Introducing Leica Viva GS14 Your Tool for All GNSS Applications The Leica GS14 is the most compact and powerful GNSS receiver.
More informationGS09 Firmware improvement details
Product Leica GS09 GNSS Version GS09 firmware v8.50 From GPS Instruments Product Management Date 09 December 2011 DVD No DVD available download from Leica myworld only Download These Release Notes contain
More informationLeica Viva GS14 Designed for Performance
Leica Viva GS14 Designed for Performance Your Vision: Flexibility and Performance Introducing Leica Viva GS14 Your Tool for All GNSS Applications The Leica Viva GS14 is the most compact and powerful GNSS
More informationProduct Leica Infinity. Date Nov 30 th, From Kevin Hanson
Product Leica Infinity Date Nov 30 th, 2017 From Kevin Hanson Leica Geosystems AG Heinrich-Wild-Strasse CH-9435 Heerbrugg Switzerland www.leica-geosystems.com Table of Contents 1 About this Release...
More informationLeica Captivate. Software Release Notes. Field Controllers: CS20, CS35 Total Stations: TS16, TS60, MS60. Release date 1 st December 2017
Leica Captivate v3.00 Software Release Notes Product Leica Captivate Field Controllers: CS20, CS35 Total Stations: TS16, TS60, MS60 Release date 1 st December 2017 Maintenance date 1 st December 2017 Available
More informationThis firmware is protected and can only be loaded onto instruments with valid firmware (software) Maintenance date.
Products TPS1200, GPS1200, RX1250 From System 1200 Product Management Date 17 th July, 2008 DVD ROM Leica SmartWorx DVD (Art. No. 755806) Version SmartWorx v6.00 Download http://downloads.leica-geosystems.com/downloads/index.htm
More informationRelease 4.1. Description
Leica MobileMatriX Release 4.1 Products - Options Packages - Hardware Description Leica MobileMatriX 4.1 Leica Geosystems, 2004-2010 1 PRODUCTS Three different Editions are available: Standard Edition
More informationLeica Viva GS14 Designed for Performance
Leica Viva GS14 Designed for Performance Your Vision: Flexibility and Performance Introducing Leica Viva GS14 Your Tool for All GNSS Applications The Leica Viva GS14 is the most compact and powerful GNSS
More informationViva TPS. TS11/15 Total Stations Connect the CS Controller and TS15 with Bluetooth. October Summary
Viva TPS October 2010 TS11/15 Total Stations Connect the CS Controller and TS15 with Bluetooth Summary This guide will show how to connect the TS instrument and CS controller for wireless operation by
More informationLeica Captivate. Software Release Notes. Field Controllers: CS20, CS35 Total Stations: TS16, TS60, MS60. Release date 7 th June 2016
Leica Captivate v2.00 Software Release Notes Product Leica Captivate Field Controllers: CS20, CS35 Total Stations: TS16, TS60, MS60 Release date 7 th June 2016 Maintenance date 1 st June 2016 Available
More informationAttaching Codesoft 6 to an ODBC Database
Attaching Codesoft 6 to an ODBC Database 1. From your Main Menu Options, go into Merge then Create ODBC query. The following Dialog Box will appear. 2. Select the button with 3 dots ( ) on it. 3. The Data
More informationAPS-3 Revision Important Quick Start Guide. Typical Box Contents
APS-3 Revision 3.0.0 Important Quick Start Guide Congratulations on purchasing your new APS-3 System. This Important Quick Start Guide contains information you need to set up and begin using your APS-3.
More informationAPS-3 with FieldGenius Configuration Manual
APS-3 with FieldGenius Configuration Manual Version 1.3 Table of contents 1 Getting Started... 2 1.1 Hardware requirements... 2 1.2 Installing FIELDGenius... 2 2 Septentrio FIELDGenius Startup... 3 2.1
More informationMSO Manual. 4th July 2015
vcomp Pty Ltd (ABN 39 103 040 311) PO Box 7356 Cloisters Square Perth WA 6850 Australia MSO Manual 4th July 2015 Overview The Mine Survey Office (MSO) application is used to process and create raw files
More informationGetting Started for GIS data
EZSurv Getting Started for GIS data Version 2.94 2012-2014 Effigis, All rights reserved. 1 Summary Information Why post-processing? Compatible data collection software Basic post-processing concepts 2
More informationAltus APS3G Quick Start guide
Altus APS3G Quick Start guide Revision 1.0.1 Congratulations on purchasing your new Altus APS3G System. This Important Quick Start Guide contains information you need to set up and begin using your Altus
More informationInstrument Interface to. LEICA TPS mid-range series (300, 400, 700, 800 and FlexLine)
Instrument Interface to LEICA TPS mid-range series (300, 400, 700, 800 and FlexLine) CONTENTS 1. Preamble 2. Install and Configure LSS 3. Configure TPS mid-range series 4. The LSS data path 5. Creating
More informationUser s guide December 2011
User s guide User s guide December 2011 WARNINGS In writing this manual every care has been taken to offer the most updated, correct and clear information possible; however unwanted errors are always
More informationTopcon GRS-1 1 Receiver Field Preparation
Topcon GRS-1 1 Receiver Field Preparation What do you need to know to get started with your Topcon GRS-1? Topcon GRS-1 Receiver - Field Preparation Some Common Questions Which TopSURV modules do I buy?
More informationFieldGenius 2010 Release Notes
FieldGenius 2010 Release Notes This document contains the release notes for all FieldGenius 2010 releases. The latest release notes can be found at the end of the document. FieldGenius 2010 4.2.0 (Released
More informationTOPCON Directions. GPS Unit
TOPCON Directions MUST HAVE: Verizon Hotspot [MiFi], antenna with pole, handheld data collector TOPCON, Bluetooth GPS Unit 1 Power On Hold button 1+ seconds Power button will flash green, turning off when
More informationPost-Processing with MobileMapper Office and NGS CORS data
Post-Processing with MobileMapper Office and NGS CORS data 23 January 2007 1. Just below the MobileMapper Office (MMO) Map Display Area, you will see the Differential Correction window. Click the Show
More informationGetting Started for GIS data
EZSurv Getting Started for GIS data Version 2.96 2012-2016 Effigis, All rights reserved. 1 Summary Information Why post-processing? Compatible data collection software Basic post-processing concepts 2
More informationLeica RX1250 & TPS 1200 Robot
Leica RX1250 & TPS 1200 Robot Total Station Extended GeoCOM & Firmware Check For FieldGenius to work correctly with your Total Station, Smart Rover and RX1250, Extended GeoCOM must be enabled. This mode
More informationSeagull #GPK. User Manual. Product: Seagull #GPK Released: FW: 1.0
Seagull #GPK User Manual Product: Seagull #GPK Released: 2018-12-06 FW: 1.0 CONTENTS GENERAL INFORMATION... 3 CONFIG FILE... 4 GENERAL... 4 EDITING... 4 SETTINGS AND VALUES TABLE... 5 FLIGHT CONTROLLER
More informationMaCORS Quick Guide. Rover Configuration for Topcon GR 3 using Carlson SurvCE 2.x & Internal CDMA Modem
MaCORS Quick Guide Rover Configuration for Topcon GR 3 using Carlson SurvCE 2.x & Internal CDMA Modem This Quick Guide outlines configuring the Topcon GR 3 with Carlson SurvCE & Internal CDMA modem to
More informationNotes on installing and using the OM-USB-5201 and OM-USB-5203 data logging devices
Notes on installing and using the OM-USB-5201 and OM-USB-5203 data logging devices Thank you for purchasing the OM-USB-5201 or OM-USB-5203 device from Omega Engineering! Please read this sheet to help
More informationAPS-3 with Seismic Surveyor
APS-3 with Seismic Surveyor Configuration Manual Revision 1.01 Page 1 APS-3 with Seismic Surveyor, Configuration Manual 2011 ALTUS Positioning Systems Inc. All rights reserved. ALTUS, the ALTUS logo, and
More informationLeica Viva Quick Guide Leica Viva: Quick Grid Guide
Leica Viva Quick Guide Leica Viva: Quick Grid Guide Leica SmartWorx Viva has a simplified means of quickly creating a site co-ordinate system called Quick Grid. This has several methods depending on site
More informationProduct Leica Infinity. Date July 13 t, From Kevin Hanson
Product Leica Infinity Date July 13 t, 2018 From Kevin Hanson Leica Geosystems AG Heinrich-Wild-Strasse CH-9435 Heerbrugg Switzerland www.leica-geosystems.com Table of Contents 1 About Infinity v3.0.1...
More informationBase Configurations Carlson SurvCE
There are six methods to set the stationary base position, organized into 2 categories: From New Position includes Read from GPS, Enter Lat/Long and Enter Grid System Coordinates. The From Known Position
More informationTechnical Note. 12 August 2009 PocketDTM Utility Surveys Brief Outline. Atlas Computers Ltd
Technical Note 12 August 2009 PocketDTM Utility Surveys Brief Outline Atlas Computers Ltd 15 Moyville Lawns Taylors Lane Rathfarnham Dublin 16 Republic of Ireland Ph: +353(0) 1 4958714/5/6 Fax: +353(0)
More informationSIDEPLATE FOR SDS/2 USER GUIDE
Please make sure to read the SIDEPLATE FOR SDS/2 INSTALLATION INSTRUCTIONS first. After following the instructions for installing SDS/2 v2016.25/v2017.16 or newer and the SidePlate for SDS/2 plugins, you
More informationLeica SmartWorx Viva Software Release Notes
Leica SmartWorx Viva Software Release Notes Release Details: Version 5.02 Release date 03 October 2013 Available for: Products Field Controllers: CS10, CS15 Total Stations: no new firmware GNSS Sensors:
More informationEvidence Recorder Release Notes
Evidence Recorder 7.1.0 Release Notes Released on: August 20, 2010 Important Notes We will be dropping support for several older builds of Evidence Recorder including: Allegro CE, Toughbook, Recon.Net,
More informationicon office release of version
Product: icon office Date: 17.12.2019 From: Torgny Israelsson icon office release of version 2019.1.11.20 We are pleased to announce the release of icon office 2019. icon office is now available as 64-bit
More informationUsing the Leica Rover. A guide to locating And capturing locations Using the Leica GPS1200 Rover. Cleveland Utilities
Using the Leica Rover A guide to locating And capturing locations Using the Leica GPS1200 Rover Cleveland Utilities Last Updated: Nov 23, 2004 Table of Contents Title Page Microstation to Field...1 4 Field
More informationSokkia GSR 2700 ISX GPRS Configuration
Sokkia GSR 2700 ISX GPRS Configuration You must be using FieldGenius 2008 v4.0.1 or newer. Start Settings Coordinate System Coordinate System Settings Access this screen by going to Start Settings Coordinate
More informationTable of Contents 1 PURPOSE SCOPE DEFINITIONS PROCEDURE... 5
Table of Contents 1 PURPOSE... 3 2 SCOPE... 3 3 DEFINITIONS... 4 4 PROCEDURE... 5 4.1 Overview - Performing a Site Calibration... 5 4.1.1 Upload Mine Grid Control... 6 4.1.2 Obtain SSM Data... 7 4.1.3
More informationFrequently Asked Questions
Frequently Asked Questions Date: 5/03/04 Product: Thales Navigation Z-Max Version: 1.5 1 General... 3 2 Memory Cards... 3 3 GPS Raw Data... 5 4 RTK... 5 5 Batteries and Chargers... 6 6 Receiver Hardware
More informationLecture ID: WT
GNSS Online Lecture # 1 Lecture ID: WT-103-401 Lecture Topic: GNSS Data Processing in RTKLIB Dinesh Manandhar Center for Spatial Information Science The University of Tokyo Contact Information: dinesh@iis.u-tokyo.ac.jp
More informationSetup a VSN Survey Style Using Trimble Access (MiFi Card)
Setup a VSN Survey Style Using Trimble Access (MiFi Card) California Surveying & Drafting Supply Technical Support Services Notes: This tutorial is designed for users with a MiFi Card/VSN Setup. In order
More informationMidland BT Updater 1.0. Option 1: Wizard procedure
Midland BT Updater 1.0 After you downloaded the BT Updater setup application from the web site, double click on it and follow the installation procedure. The BTUpdater application is automatically installed
More informationGSR Reference Station Software
GNSS Reference Station GSR Reference Station Software Reference Manual GNSS Reference Station Tplljb GSR Reference Station Software Version 7.2.1 Preliminary For Internal Use Only Reference Manual Preliminary
More informationSetup a VSN Survey Style Using Trimble Access (Bluetooth Phone)
Setup a VSN Survey Style Using Trimble Access (Bluetooth Phone) California Surveying & Drafting Supply Technical Support Services Notes: This tutorial is designed as a tutorial for users with a cell phone/vsn
More informationLeica Geosystems CS20 Data Controller CS - PXS8 CDMA Cellular Modem Setup for Verizon Wireless, Internet Connection for Network RTK Rover Surveying.
Leica Geosystems CS20 Data Controller CS - PXS8 CDMA Cellular Modem Setup for Verizon Wireless, Internet Connection for Network RTK Rover Surveying. Turn on the CS20 Data Controller, start the Leica Captivate
More informationIncrease Field Survey Efficiency by Merging Technologies in NOVA MultiStation. Vincent Lui Leica Geosystems Ltd
Increase Field Survey Efficiency by Merging Technologies in NOVA MultiStation Vincent Lui Leica Geosystems Ltd Advantages of Laser Scanning Advantages of TPS Measurements Advantages of Imaging Advantages
More informationLeica Viva SmartWorx Viva on TS
Leica Viva SmartWorx Viva on TS Contents 2. Volumes 3. Check & Adjust 4. CS Connection Wizard 5. Robotic Screen 6. Summary 2 Contents 2. Volumes 3. Check & Adjust 4. CS Connection Wizard 5. Robotic Screen
More informationGIS DataPRO TM. Getting Started with the GIS DataPRO Software. Version 3.0 English
GIS DataPRO TM Getting Started with the GIS DataPRO Software Version 3.0 English Symbols Used in this Manual Symbols used in this manual have the following meanings: Important paragraphs which must be
More informationAltus APS3 Configure Rover for Radio, NTRIP or GPRS RTK Link
Altus APS3 Configure Rover for Radio, NTRIP or GPRS RTK Link You must be using FieldGenius 2010 v4.3.0 or newer. This document was written using FieldGenius 2010 v4.3.0.11 Coordinate System Settings Coordinate
More informationPRO 1080P COVERT SPY PEN QUICK START GUIDE
Before Operating make sure to charge the pen through the USB charger/pc for 8Hrs How to Charge the Battery: Connect the Hidden Camera to a PC or USB power supply Initially charge device for 8 hours to
More informationLPR for Windows 95/98/Me/2000 TCP/IP Printing User s Guide
LPR for Windows 95/98/Me/2000 TCP/IP Printing User s Guide Rev. 02 (August, 2001) Copyright Statement Trademarks Copyright 1997 No part of this publication may be reproduced in any form or by any means
More informationNikon Capture NX "How To..." Series
1 of 8 5/15/2007 2:24 PM Nikon Capture NX "How To..." Series Article 22 - How to convert multiple RAW NEF images to JPEG Purpose: Using the "Batch" process, you can convert all RAW NEF images in a single
More informationAppserv Internal Desktop Access Mac OS Device with Safari Browser. Enter your Appserv username and password to sign in to the Website
Appserv Desktop Access Logging on from a Mac OS device Step 1. To sign in to the Appserv Desktop Access website, enter the following address into the Safari browser address bar. Please Note: This documentation
More informationSXBlue RTN. User s Guide. (for Windows Desktop and Windows Mobile 6.x) Revision Date: April 2012 (rev 1.0)
SXBlue RTN User s Guide (for Windows Desktop and Windows Mobile 6.x) Revision Date: April 2012 (rev 1.0) Table of Contents 1. Introduction...1 2. Installing SXBlue RTN...2 2.1 On a Desktop PC...2 2.2 On
More informationQUICK START GUIDE. SOLO Forest
QUICK START GUIDE SOLO Forest Software Installation 1. For PC installation, run the.msi file. 2. For Mobile device installation, copy the.cab file onto the device 3. Run the.cab file Starting the Program
More informationtrimble r10 GNSS System
TRIMBLE R10 SERIES RECEIVER QUICK START GUIDE trimble r10 GNSS System C Warning: For safety information, refer to the Safety Information section of the Trimble R10 GNSS Receiver User Guide. Five simple
More informationBackup everything to cloud / local storage. CloudBacko Home. Essential steps to get started
CloudBacko Home Essential steps to get started Last update: December 2, 2016 Index Step 1). Installation Step 2). Configure a new backup set, trigger a backup manually Step 3). Configure other backup set
More informationDJI MATRICE 600 Release Notes
Date : 2018.04.17 Aircraft Firmware : V 1.0.1.66 DJI GO App : ios V 3.1.31, Android V 3.1.30 DJI Assistant 2 : V 1.1.7 Aircraft Firmware: Improved altitude measuring precision by lowering barometer drift
More informationLeica Viva Imaging Enrich your Surveying Workflow
Leica Viva Imaging Enrich your Surveying Workflow Your Vision: Images that Welcome to Leica Viva Imaging Enrich your Surveving Workflow Leica Viva Imaging enriches your surveying workflow with visual documentation
More informationLeica Viva CS & GS Driver Installation
Leica Viva CS & GS Driver Installation Contents Introduction...2 Driver Installation...2 Testing the Connection...4 FAQs...5 1. The drivers seem to be installed correctly, but I can not view the GS webserver
More informationVirtual Computer Lab (VCL)
Purpose: Audience: Describes steps to setup and use the Virtual Computer Lab (VCL) Authenticated IUP users What is VCL? The IUP Virtual Computer Lab (VCL) is a virtual lab desktop. The virtual desktop
More informationQuick Start Guide for Using TDS NOMAD GPS Equipment (For Team Leaders) Initial Unit Check
Quick Start Guide for Using TDS NOMAD GPS Equipment (For Team Leaders) Initial Unit Check For each GPS unit, ensure you have: TDS NOMAD GPS Unit Garmin backpack receiver (antenna) Portable battery pack
More informationQpad X5 User Guide Hi-Target Surveying Instrument Co., Ltd. All Rights Reserved
Qpad X5 User Guide Hi-Target Surveying Instrument Co., Ltd. All Rights Reserved Manual Revision Preface File number: Revision Date Revision Level Description 2016-06-03 1 Qpad X5 User Guide II Qpad X5
More informationFIG XXV Congress 2014 Engaging commercial RTK Network Services: Experiences from SmartNet Australia
Please insert a picture (Insert, Picture, from file). Size according to grey field (10 cm x 25.4 cm). Scale picture: highlight, pull corner point Cut picture: highlight, choose the cutting icon from the
More informationLeica Manual TS Equipment List
Leica Manual TS Equipment List Table of Contents FlexLine plus Totalstation series 5 1 FlexLine plus 5 1.1 Overview 5 1.2 Models 5 FlexLine plus Options, Software & Specific Accessories 7 2 Additional
More informationVersion 1.0 English. Leica GS10/GS15 Quick Guide
Version 1.0 English Leica GS10/GS15 Quick Guide GS10/GS15, Important Information about your Instrument 1 Important Information about your Instrument 2 Read and follow the User Manual on the accompanying
More informationLeica Geosystems TPS
Leica Geosystems TPS Leica Geosystems Total Stations Semiprofessional Basic TS15 TS50 MS50 TM50 TS11 Monitoring ScanStation TS09 plus TS06 plus Professional TS02 plus Flexline Leica FlexLine plus Product
More informationWindows. Updating Digital SLR Camera Firmware. Get ready
Updating Digital SLR Camera Firmware Windows Thank you for choosing a Nikon product. This guide describes how to perform this firmware update. If you are not confident that you can perform the update successfully,
More informationContents Introduction Installation/Deinstallation of SurveyOffice Getting Started... 3
Getting Started Manual MADE TO MEASURE Contents Contents... 1 1 Introduction... 2 2 Installation/Deinstallation of SurveyOffice... 2 3 Getting Started... 3 3.1 Register:... 4 3.1.1 Register Instruments:...
More informationUpgrading Print Director to PCS Director
Upgrading Print Director to PCS Director Overview: Because of the new features and functionality of PCS Director (PCS), upgrading from Print Director (PD) requires preparation, planning, and resource allocation
More informationLeica Campus Knowledge at your Fingertips
Leica Campus Knowledge at your Fingertips Training Schedule 2010 1 Leica Campus Training Schedule 2010 Leica Campus Training Packages offers flexible courses designed to suit your company s needs and the
More informationNavigating Viewpoint V6 Exploring the Viewpoint Main Menu
Navigating Viewpoint V6 Exploring the Viewpoint Main Menu Table of Contents About this Course 3 Viewpoint Folder Structure 4 File Menu 5 View Menu 6 Options Menu 7 User Options 7 Help Menu 9 Support 9
More informationEvidence Recorder Release Notes
Evidence Recorder 6.0.0 Release Notes Released on: October 5, 2009 Licensing Changes This release has had one big change and that is a new licensing system that gives us more flexibility to add different
More informationTHALES NAVIGATION. FAST Survey. Field Guide.
THALES NAVIGATION FAST Survey Field Guide www.thalesnavigation.com Printed in France. Part Number: 630887-01, Revision A. No part of this publication or the computer programs described in it may be reproduced,
More informationMobileMapper 300 Frequently Asked Questions
April 13th, 2015 MobileMapper 300 Frequently Asked Questions What is the main application of MobileMapper 300? MobileMapper 300 provides professional grade accuracy to consumer handheld devices. A customer
More informationHow to Update Zebra GX420d Printer Firmware
1 How to Update Zebra GX420d Printer Firmware DO NOT POWER ON THE ZEBRA PRINTER OR CONNECT THE USB CABLE UNTIL INSTRUCTED TO DO SO! 1. Download Zebra Setup Utilities from the following URL: http://print.managementsolutionsofva.com/downloads/zsu-1191204.exe.
More informationLow cost GNSS receivers: navigation and monitoring activities
PHD in Environmental and Infrastructure Engineering XXIX cycle Low cost GNSS receivers: navigation and monitoring activities Ph.D.'s activity final report Marco Negretti marco.negretti@polimi.it Supervisor:
More informationGPS Vector File Convertor
RW52GPS GPS Vector File Convertor Date: 20 August 2016 Build: 111 By: Mark Silver, ms@igage.com, +1-801-412-0011 x16 General Description RW52GPS is a 32-bit Windows convertor. It is distributed as a single
More informationOur Challenge : To manage an increasingly complex world!
SmartPhones Our Challenge : To manage an increasingly complex world! The Leica Response: To enable the capture, and virtualisation of this complex world quickly, easily and accurately New hardware and
More informationHD32MTLogger Software Manual for the instrument HD32MT.1 Introduction
HD32MTLogger Software Manual for the instrument HD32MT.1 Introduction WARNING: The software must always be run as administrator! The HD32MTLogger program allows management of the HD32MT.1 datalogger from
More informationBLUETOOTH. AMPRO 2000 / OPTIMA 7 Using Bluetooth with the MRU4u app
BLUETOOTH 1 P a g e This app is available for both Android and ios. Download the MRU4u app from the Play-store or APP-store. 2 P a g e INDEX: Analyzer Bluetooth settings 4 Android phone Bluetooth connection
More informationTopSURV: Collecting field data using the Auto Topo function. Oscar R. Cantu
TopSURV: Collecting field data using the Auto Topo function Oscar R. Cantu Have a Question? At anytime during today s webinar, if you have any questions, please type them within the Questions section of
More informationUser Manual For TX204B/TX204G/TX306 Receivers
User Manual Version V1.0-20171124 User Manual For TX204B/TX204G/TX306 Receivers 2017 Tersus GNSS Inc. All rights reserved. Sales & Technical Support: sales@tersus-gnss.com & support@tersus-gnss.com More
More informationTrimble Survey GNSS Firmware Version 5.01 (April 2015) The following table identifies the Survey GNSS receivers supported by this revision.
RELEASE NOTES 15 APRIL 2015 TRIMBLE SURVEY GNSS FIRMWARE Trimble Survey GNSS Firmware Version 5.01 (April 2015) Requirements This firmware version includes improvements to the Survey Receiver firmware.
More informationPACIFIC CREST RADIO CONFIGURATION
PACIFIC CREST RADIO CONFIGURATION using PDLCONF version 4.0 software To configure the Pacific Crest Radios (PDL Base and/or the Internal PDL Rover Radio) you will need to have the following software installed
More informationMSO V2.02 Release Notes
vcomp Pty Ltd (ABN 39 103 040 311) PO Box 7356 Cloisters Square Perth WA 6850 Telephone +618 9312 6158 Fax +618 9312 6158 Release Notes 31 st July 2013 MSO V2 Upgrade Q & A Q. Can I install and use both
More informationConfiguring Esri s Collector 10.4 on Android with your Arrow receiver
Configuring Esri s Collector 10.4 on Android with your Arrow receiver Before the first step, make sure that you have initially paired your Arrow with your Android device. If not, we suggest you to download
More informationSoftware Release Notice
Introduction NavCom Technology, Inc. A John Deere Company 20780 Madrona Ave, Torrance, CA. 90503 Tel: 310-381-2000 Fax: 310-381-2001 E-mail: customerservice@navcomtech.com Software Release Notice V3.6.9.0
More informationLeica Viva TS11 & TS15 Hardware
Leica Viva TS11 & TS15 Hardware Contents 1. Introduction 2. Product Variants 3. Side Cover 4. Display and Keyboard 5. Environmental Rating 6. Telescope 8. Operating System & Software 9. Summary 1. Introduction
More informationIntroduction to Solo Forest
Introduction to Solo Forest Project Settings Collecting Data Office Procedures - Exporting Shapefiles - Syncing with the PC - Transferring files Opening Solo Forest To open Solo Forest, select Start >
More informationX90 GPS X90GPS RTK. 1 -
X90GPS RTK : : 1 - www.nprco.com 3 3 3 4 4 4 4 4 5 5 5 10 11 12 12 14 14 15 16 16 18 19 19 19 20 20 21 22 22 25 28 31 31 32 36 36 36 36 37 39 41 44.1 1 1.2.2 2.1 2.1.1 2.1.2 2.1.3 2.2.3 3.1 3.2 3.2.1 3.2.2
More informationHow To Combined TPS and GPS adjustment
How To Combined TPS and GPS adjustment Version 4.4 Sweco Nederland B.V. All rights reserved Contents 1. Introduction 3 2. New MOVE3 Project 3 3. Options 4 4. Default standard deviations 6 5. Import GNSS/GPS
More information