CHANNEL BLOCK SOLID. Step 7. For the Placement Point, click the bottom left gray rectangle and click OK. to fit drawing on the screen.
|
|
|
- Charla Hubbard
- 6 years ago
- Views:
Transcription
1 Chapter 9 CHANNEL BLOCK SOLID A. Create Rectangle. Step 1. Change to the Front View. Use green Front View or ALT-6 F. Hold down ALT and press 6. Key-in F. Step 3. Create. Step 4. Rectangle. Step 5. 1 Point. Step 6. Set: Width 3 and Height 2. Step 7. For the Placement Point, click the bottom left gray rectangle and click OK. Step 8. Origin. Step 9. Use ALT-F1 or Step 10. MAIN MENU. to fit drawing on the screen. Delete Line B. Delete Top Line. Step 1. The top line is no longer needed. Use F5 to delete. Press F5 and click the top line of the rectangle, Fig. 1. Press ESC to exit delete. Step 2. Use F3 or to repaint the screen. Fig. 1 C. Draw Lines. Step 1. MAIN MENU. Step 2. Create. Step 3. Line. Step 4. Endpoints. Step 5. Draw the lines in Fig. 2. Use the grid to determine the location of the lines. Fig. 2 Mastercam CHANNEL BLOCK SOLID Page 9-1 Brookside Middle School Tech Ed cudacountry@comcast.net
2 D. Save Your File. Step 1. MAIN MENU. Step 2. File. Step 3. Save. Step 4. Key-in chanblk file name and press ENTER. E. Extrude Block Solid. Step 1. Change to the Isometric View. Use the green or ALT-6 I and to fit drawing. Step 3. Solids. Step 4. Extrude. Step 5. Chain. Step 6. Click a line of the geometry, Fig. 3. Step 7. Done. Fig. 3 Step 8. The direction arrow on the chain should point to the back, Fig. 3. If the arrow points in the wrong direction, click Reverse It. Step 9. Done. Step 10. Set: Distance = 2 and click OK, Fig. 4 and Fig. 5. Step 11. Turn on the shading, use ALT-S. F. Create Center Lines For Holes. Fig. 4 Fig. 5 Step 1. Change to the Front View. Use the green Front View or ALT-6 F. Hold down ALT and press 6. Key-in F. Step 2. Draw the next lines, the center lines in a different color. Change the color to green. Click the color swatch in the Secondary Menu (bottom of the menu). Click green, number 10 and click OK. Mastercam CHANNEL BLOCK SOLID Page 9-2
3 Step 3. Change the line style to Center Lines. Click Attributes in the Secondary Menu. Set Line Style to Center and click OK. Step 4. Turn off the shading, use ALT-S. Step 5. MAIN MENU. Step 6. Create. Step 7. Line. Fig. 6 Step 8. Parallel. Step 9. Side/Distance. Step 10. Draw parallel vertical lines in from both sides, Fig. 6. Click the side of the rectangle to select line. Click inside of the rectangle to indicate offset direction. Key-in.5 for distance and press ENTER. Repeat on the other side of rectangle. That is, click the side of the rectangle and indicate offset direction by clicking slightly inside the rectangle then press ENTER to use.5. Fig. 7 Step 11. Continue to draw parallel lines up from the bottom and down from both top lines. Always select a new line. To indicate side, click inside the rectangle and press ENTER to use.5, Fig. 7. G. Create Circles. Step 1. Draw the next circle in a different color. Change the color to yellow. Click the color swatch in the Secondary Menu (bottom of the menu). Click yellow, number 14 and click OK. Step 2. Change the line style back to solid. Click Attributes in the Secondary Menu. Set Line Style to Solid and click OK. Step 3. MAIN MENU. Step 4. Create. Step 5. Arc. Step 6. Circle Point and Diameter. Step 7. Key-in.4 for diameter and press ENTER. Mastercam CHANNEL BLOCK SOLID Page 9-3
4 Step 8. Intersection. Step 9. Click Line 1 and Line 2 at a circle. Press I key and click another circles center lines, Line 1 and 2. Remember to use the I key before you click the center lines, Fig. 8. Step 10. Save your drawing. Use Alt-A and press ENTER. H. Cut Out Holes. Step 1. Change to the Isometric View. Use the green or ALT-6 I. Fig. 8 Step 3. Solids. Step 4. Extrude. Step 5. Single. Step 6. Click all four circles. Step 7. Done. Fig. 9 Step 8. The direction arrow on the chain should point to the back, Fig. 9. If the arrow points in the wrong direction, click Reverse It. Step 9. Done. Step 10. Set: Cut Body. Distance = 2 and click OK, Fig. 10 and Fig. 11. Step 11. Turn on the shading, use ALT-S. Fig. 10 Fig. 11 Mastercam CHANNEL BLOCK SOLID Page 9-4
5 I. Set Construction Plane To Graphic View. Step 1. Change to the Isometric View. Use the green Key-in I. Step 2. Click Cplane in the Secondary Menu. Step 3. Next Menu. Step 4. =Gview. or ALT-6 I. Hold down ALT and press 6. J. Add Your Name And Period To Drawing. Step 1. Use Page Down to reduce the drawing. Use: Create, Drafting, Note commands to add your names and period to the drawing. Step 2. Save your drawing. Use Alt-A and press ENTER. Mastercam CHANNEL BLOCK SOLID Page 9-5
Step 3. Rectangle. Fig. 1. Step 6. For the Placement Point, click the bottom left gray rectangle and click OK, Fig. 2. to fit the drawing on screen.
Chapter 24 BOAT SOLID A. Name Level. Hold down ALT and press Z. Step 2. Key-in block for Name and click OK, Fig. 1. B. Create Rectangle. Step 3. Rectangle. Fig. 1 Step 4. 1 Point. Step 5. Key-in 9 for
Chapter 3. CO2 Car SolidWorks to Mastercam. A. Enable MasterCam Direct. Step 1. If necessary, open your body file in SolidWorks.
Chapter 3 CO2 Car SolidWorks to Mastercam X 2007 A. Enable MasterCam Direct. Step 1. If necessary, open your body file in SolidWorks. Step 2. Click Tools Menu > Add-Ins. Step 3. In the dialog box scroll
CO2 Rail Car. Wheel Rear Px. on the Command Manager toolbar.
Chapter 6 CO2 Rail Car Wheel Rear Px A. Sketch Construction Lines. Step 1. Click File Menu > New, click Part Metric and OK. Step 2. Click Front (plane) in the Feature Manager (left panel), Fig. 1. Step
Boat Hull Solid. (Alt-2). in ribbon bar to fix and close ribbon Fig. 3 Mastercam X7 BOAT HULL SOLID Page 29-1
Mastercam X7 Chapter 29 A. Open Boat Block File. Step 1. Open your BOAT BLOCK file. Boat Hull Solid B. Save As BOAT HULL SOLID Step 1. Click File Menu > Save As. Step 2. Key-in BOAT HULL SOLID for the
Cudacountry Radial. Fig. 2. Point. Fig. 4. Mastercam 2017 Cudacountry Radial Page 19-1
Mastercam 2017 Chapter 19 Cudacountry Radial A. Create Rectangle. Step 1. If necessary start a new Mastercam file, click New QAT. (Ctrl-N) on the Quick Access Toolbar Step 2. On the Wireframe tab click
Belt Buckle A. Create Rectangle. Step 1. If necessary start a new Mastercam file, click New
Mastercam 2017 Chapter 35 Belt Buckle A. Create Rectangle. Step 1. If necessary start a new Mastercam file, click New (Ctrl-N) on the Quick Access Toolbar QAT. Step 2. On the Wireframe tab click Rectangle.
Chapter 36. Mastercam Jewelry Box Fixture. A. Sketch Fixture Rectangle. Step 1. If necessary start a new Mastercam file, click New
Mastercam 2017 Chapter 36 Jewelry Box Fixture A. Sketch Fixture Rectangle. Step 1. If necessary start a new Mastercam file, click New (Ctrl-N) on the Quick Access Toolbar QAT. Step 2. On the Wireframe
Catamaran A. Create Rectangle. Step 1. If necessary start a new Mastercam file, click File Menu > New.
Mastercam X7 Chapter 26 Catamaran A. Create Rectangle. Step. If necessary start a new Mastercam file, click File Menu > New. Step 2. Click Create Menu > Rectangle or click Rectangle Tool Step 3. In the
Jewelry Box Lid. A. Sketch Lid Circle. Step 1. If necessary start a new Mastercam file, click FILE Menu > New. Fig. 3
Mastercam X9 Chapter 39 Jewelry Box Lid A. Sketch Lid Circle. Step 1. If necessary start a new Mastercam file, click FILE Menu > New. Step 2. Click CREATE Menu > Arc > Circle Center Point. Step 3. Key-in
Skateboard. Hanger. in the Feature Manager and click Sketch on the Context toolbar, Fig. 1. Fig. 2
Chapter 3 Skateboard Hanger A. Sketch1 Lines. Step 1. Click File Menu > New, click Part Metric and OK. Step 2. Click Right Plane in the Feature Manager and click Sketch on the Context toolbar, Fig. 1.
Delta Dart. Socket. (L) on the Sketch toolbar. Fig. 1. (S) on the Sketch toolbar. on the Sketch toolbar. on the Standard Views toolbar.
Chapter 6 Delta Dart Socket A. Sketch. Step 1. Click File Menu > New, click Part Metric and OK. Step 2. Click Front Plane in the Feature Manager and click Sketch from the Content toolbar, Fig. 1. Step
Chapter 39. Mastercam Jewelry Box Tray. A. Sketch Tray Circle. B. Twin Edge Point Circles. Mastercam 2017 Tray Jewelry Box Page 39-1
Mastercam 2017 Chapter 39 A. Sketch Tray Circle. Jewelry Box Tray Step 1. If necessary start a new Mastercam file, click New (Ctrl-N) on the Quick Access Toolbar QAT. Step 2. On the Wireframe tab click
Fig. 2 Mastercam 2020 Spinning Top SW 19 to MCam20 TOOLPATHS Page 13-1
Mastercam 2020 Chapter 13 Spinning Top SOLIDWORKS 19 to Mastercam 2020 A. Open File in Mastercam 2020. Step 1. If necessary, save your Handle and Flywheel parts file in SOLIDWORKS. Step 2. In Mastercam
Chair. Top Rail. on the Standard Views toolbar. (Ctrl-7) on the Weldments toolbar. at bottom left corner of display to deter- mine sketch plane.
Chapter 7 A. 3D Sketch. Step 1. If necessary, open your CHAIR file. Chair Top Rail Step 2. Click Isometric on the Standard Views toolbar. (Ctrl-7) Step 3. Zoom in around top of back leg, Fig. 1. To zoom,
Speedway. Body. (S) on the Sketch toolbar. Fig. 1
Chapter 1 A. New Part. Step 1. Click File Menu > New. Speedway Body Step 2. Click Part from the list and click OK, Fig. 1. B. Sketch Construction Rectangle. Step 1. Click Right Plane in the Feature Manager
Toolpaths for Fuselage
Mastercam 2017 Chapter 18 Chapter 22 23 Airplane Toolpaths for Fuselage Finish Blend A. Hide Top Surface. Step 1. If necessary, open your FUSELAGE file from Chapter 17. Step 2. On the Home tab click Hide/Unhide
Body. Chapter 1. Simple Machines. A. New Part. Step 1. Click File Menu > New.
Chapter 1 A. New Part. Step 1. Click File Menu > New. Simple Machines Body Step 2. Click Part from the list and click OK, Fig. 1. B. Sketch Construction Rectangle. Step 1. Click Right Plane in the Feature
Battery Holder. Chapter 9. Boat. A. Front Extrude. Step 1. Click File Menu > New, click Part and OK. SolidWorks 10 BATTERY HOLDER AA BOAT Page 9-1
Chapter 9 Boat Battery Holder A. Front Extrude. Step 1. Click File Menu > New, click Part and OK. AA Step 2. Click Front (plane) in the Feature Manager and click Sketch from the Content toolbar, Fig. 1.
Toolpaths for Fuselage
Mastercam Chapter 18 Chapter 22 23 Airplane Toolpaths for Fuselage Finish Blend A. Machine Type and Stock Setup. Step 1. If necessary, open your FUSELAGE file from Chapter 17. Step 2. If necessary, display
Airplane. Chapter 21. Mastercam A. Create Rectangle. B. Save As AIRPLANE. C. Set Grid and Snap.2. Mastercam 2017 Airplane Page 21-1
Mastercam 2017 Chapter 21 A. Create Rectangle. Airplane Step 1. If necessary start a new Mastercam file, click New on the Quick Access Toolbar QAT (Ctrl-N). Step 2. On the Wireframe tab click Rectangle.
Mastercam X9 for SOLIDWORKS
Chapter 21 CO2 Shell Car Mastercam X9 for SOLIDWORKS A. Enable Mastercam for SOLIDWORKS. Step 1. If necessary, turn on Mastercam for SOLIDWORKS, click the flyout of Options on the Standard toolbar and
Inventor 201. Work Planes, Features & Constraints: Advanced part features and constraints
Work Planes, Features & Constraints: 1. Select the Work Plane feature tool, move the cursor to the rim of the base so that inside and outside edges are highlighted and click once on the bottom rim of the
Nose Cone. Chapter 4. Rocket 3D Print. A. Revolve. Step 1. Click File Menu > New, click Part and OK. SOLIDWORKS 16 Nose Cone ROCKET 3D PRINT Page 4-1
Chapter 4 Rocket 3D Print Nose Cone A. Revolve. Step 1. Click File Menu > New, click Part and OK. Step 2. Click Front Plane in the Feature Manager and click Sketch on the content toolbar, Fig. 1. Step
3ds Max Cottage Step 1. Always start out by setting up units: We re going with this setup as we will round everything off to one inch.
3ds Max Cottage Step 1 Always start out by setting up units: We re going with this setup as we will round everything off to one inch. File/Import the CAD drawing Be sure Files of Type is set to all formats
CO2 Car Assembly. in the Property Manager to place the part at the origin, Fig. 1. on the Assemblies toolbar. SolidWorks Assembly CO2 CAR Page 8-1
Chapter 8 CO2 Car Assembly A. Insert Axles and Wheels. Step 1. Click File Menu > New, click Assembly Metric and OK. Step 2. Click Keep Visible in the Property Manager, Fig. 1. Step 3. Click Browse in the
Penny Hockey SOLIDWORKS 17 to Mastercam 2017 A. Open File in Mastercam Step 1. If necessary, save your BASE file in SOLIDWORKS.
Mastercam 2017 Chapter 22 Chapter 7 Penny Hockey SOLIDWORKS 17 to Mastercam 2017 A. Open File in Mastercam 2017. Step 1. If necessary, save your BASE file in SOLIDWORKS. Step 2. In Mastercam 2017, click
Solar Car. Chassis. in the Feature Manager and click Sketch from the Content toolbar, Fig. 2. Origin. on the Command Manager toolbar. Fig.
Chapter 1 A. New Part. Step 1. Click File Menu > New. Solar Car Chassis Step 2. Click Part from the list and click OK, Fig. 1. B. Sketch Chassis. Step 1. Click Right Plane in the Feature Manager and click
Skateboard. Hanger. in the Feature Manager and click Sketch. (S) on the Sketch. Line
Chapter 3 Skateboard Hanger A. Sketch 1. Step 1. Click File Menu > New, click Part Metric and OK. Step 2. Click Right Plane from the Content toolbar, Fig. 1. in the Feature Manager and click Sketch Step
TRAINING GUIDE WCS - VIEW MANAGER - PART-2
TRAINING GUIDE WCS - VIEW MANAGER - PART-2 Mastercam Training Guide Objectives The learner will create the geometry and toolpaths for WCS-Part-2. This Lesson will cover the following topics: Create a 3-dimensional
Body. Chapter 2. CO2 Rail Car E. A. Save as "BODY RAIL E". Step 1. Open your BLANK file.
Chapter 2 A. Save as "BODY RAIL E". Step 1. Open your BLANK file. Step 2. Click File Menu > Save As. Step 3. Key-in BODY RAIL E for the filename and press ENTER. CO2 Rail Car E Body B. Appearance. Step
CO 2 Shell Car. Body. in the Feature Manager and click Sketch from the context toolbar, Fig. 1. on the Standard Views toolbar.
CO 2 Shell Car Chapter 2 Body A. Save as "BODY". Step 1. If necessary, open your BLANK file. Step 2. Click File Menu > Save As. Step 3. Key-in BODY for the filename and press ENTER. B. FRONT Wheel Shell.
CO2 Shell Car. Axle Retainer. in the Feature Manager and click Sketch from the Content toolbar, Fig. 1. (L) on the Sketch toolbar. Fig.
Chapter 17 CO2 Shell Car Axle Retainer A. Sketch. Step 1. Click File Menu > New, click Part Metric and OK. Step 2. Click Top Plane in the Feature Manager and click Sketch from the Content toolbar, Fig.
H Stab and V Stab. Chapter 6. Glider. A. Open and Save as "H STAB". Step 1. Open your STABILIZER BLANK file.
Chapter 6 Glider H Stab and V Stab A. Open and Save as "H STAB". Step 1. Open your STABILIZER BLANK file. Step 2. Click File Menu > Save As. Step 3. Key-in H STAB for the filename and press ENTER. B. Sketch
TRAINING GUIDE WCS-PART-1
TRAINING GUIDE WCS-PART-1 Mastercam Training Guide Objectives The learner will create the geometry for WCS-Part-1. This Lesson will cover the following topics: Create a 3-dimensional drawing by: Creating
Simple Machines. Body. Step 4. Start at Origin and sketch the 8 lines, Fig. 2. Fig. 1. Origin
Chapter 1 Simple Machines Body A. Sketch. Step 1. Click File Menu > New, click Part and OK. Step 2. Click Right Plane in the Feature Manager and click Sketch on the context toolbar, Fig. 1. Step 3. Click
Delta Dart. Propeller. in the Feature Manager and click Sketch from the Content toolbar, Fig. 1. on the Sketch toolbar.
Chapter 8 Delta Dart Propeller A. Base for Blade. Step 1. Click File Menu > New, click Part Metric and OK. Step 2. Click Top Plane in the Feature Manager and click Sketch from the Content toolbar, Fig.
Blank. Chapter 1. CO2 Rail Car. A. New Metric Part. Step 1. Click File Menu > New. B. Body. Step 1. Click Right Plane
Chapter 1 A. New Metric Part. Step 1. Click File Menu > New. CO2 Rail Car Blank Step 2. Click Part Metric from the list and click OK, Fig. 1. If you are not using SolidWorks templates (you should be),
TRAINING GUIDE. Sample. Distribution. not for LATHE-LESSON-1 FACE, ROUGH, FINISH AND CUTOFF
TRAINING GUIDE LATHE-LESSON-1 FACE, ROUGH, FINISH AND CUTOFF Mastercam Training Guide Objectives You will create the geometry for Lathe-Lesson-1, and then generate a toolpath to machine the part on a CNC
F-1 Car. Blank. in the Feature Manager and click Sketch from the Content toolbar, Fig. 3. Origin. on the Features toolbar.
Chapter 1 A. New Metric Part. Step 1. Click File Menu > New. F-1 Car Blank Step 2. Click Part Metric from the list of templates and click OK, Fig. 1. If you are not using SOLIDWORKS templates (you should
TRAINING GUIDE SOLIDS-LESSON-3
TRAINING GUIDE SOLIDS-LESSON-3 Mastercam Training Guide Objectives You will generate the solid model from the existing 2-dimensional geometry. This Lesson covers the following topics: Open an existing
F1 Car. Wheel. in the Feature Manager and click Sketch on the Context toolbar, Fig. 1. (S) on the
Chapter 3 F1 Car Wheel A. Sketch Lines. Step 1. Click File Menu > New, click Part Metric and OK. Step 2. Click Front Plane in the Feature Manager and click Sketch on the Context toolbar, Fig. 1. Step 3.
Terminal. Chapter 16. E-Car. A. Component from Design Library. SOLIDWORKS 17 Terminal E-CAR Page 16-1
Chapter 16 E-Car Terminal A. Component from Design Library. Step 1. Click the Design Library tab in the Task Pane (right side of graphics area), Fig. 1. Step 2. Expand routing and click electrical folder
Simple Machines. Wheel. in the Feature Manager and click Sketch. on the Command Manager toolbar.
Chapter 3 Simple Machines Wheel A. Wheel. Step 1. Click File Menu > New, click Part and OK. Step 2. Click Right Plane from the Content toolbar, Fig. 1. in the Feature Manager and click Sketch Step 3. Click
Brief Introduction to MasterCAM X4
Brief Introduction to MasterCAM X4 Fall 2013 Meung J Kim, Ph.D., Professor Department of Mechanical Engineering College of Engineering and Engineering Technology Northern Illinois University DeKalb, IL
Battery Holder 2 x AA
Chapter 22 JSS Battery Holder 2 x AA A. Front Extrude. Step 1. Click File Menu > New, click Part Metric and OK. Step 2. Click Front Plane in the Feature Manager and click Sketch from the Context toolbar,
Tail Hook. Chapter 14. Airplane. A. Construction Rectangle. Step 1. Click File Menu > New, click Part and OK.
Chapter 14 Airplane Tail Hook A. Construction Rectangle. Step 1. Click File Menu > New, click Part and OK. Step 2. Click Right (plane) in the Feature Manager and click Sketch from the Content toolbar,
QuickTutor. An Introductory SilverScreen Modeling Tutorial. Solid Modeler
QuickTutor An Introductory SilverScreen Modeling Tutorial Solid Modeler TM Copyright Copyright 2005 by Schroff Development Corporation, Shawnee-Mission, Kansas, United States of America. All rights reserved.
Wheel GT-F. Chapter 5. CO2 Shell Car. A. Sketch. Step 1. Click File Menu > New, click Part Metric and OK.
Chapter 5 CO2 Shell Car Wheel GT-F A. Sketch. Step 1. Click File Menu > New, click Part Metric and OK. Step 2. Click Front Plane in the Feature Manager and click Sketch on the context toolbar, Fig. 1.
SOLIDWORKS: Lesson III Patterns & Mirrors. UCF Engineering
SOLIDWORKS: Lesson III Patterns & Mirrors UCF Engineering Solidworks Review Last lesson we discussed several more features that can be added to models in order to increase their complexity. We are now
Mastercam X6 for SolidWorks Toolpaths
Chapter 21 CO2 Shell Car Mastercam X6 for SolidWorks Toolpaths A. Enable Mastercam for SolidWorks. Step 1. If necessary, turn on Mastercam for SolidWorks, click Tools Menu > Add-Ins. Step 2. In the dialog
Fuselage and Sharks Tooth
Chapter 4 Glider Fuselage and Sharks Tooth A. Save as "FUSELAGE". Step 1. Open your FUSELAGE BLANK file. Step 2. Click File Menu > Save As. Step 3. Key-in FUSELAGE for the filename and press ENTER. B.
TRAINING GUIDE LATHE-LESSON-1 FACE, ROUGH, FINISH AND CUTOFF
TRAINING GUIDE LATHE-LESSON-1 FACE, ROUGH, FINISH AND CUTOFF Mastercam Training Guide Objectives You will create the geometry for Lathe-Lesson-1, and then generate a toolpath to machine the part on a CNC
Propeller. Chapter 13. Airplane. A. Base for Blade. Step 1. Click File Menu > New, click Part and OK.
Chapter 13 Airplane Propeller A. Base for Blade. Step 1. Click File Menu > New, click Part and OK. Step 2. Click Top Plane in the Feature Manager and click Sketch toolbar, Fig. 1. from the Content Step
TRAINING GUIDE. Sample not. for Distribution LATHE-LESSON-1 FACE, ROUGH, FINISH AND CUTOFF
TRAINING GUIDE LATHE-LESSON-1 FACE, ROUGH, FINISH AND CUTOFF Mastercam Training Guide Objectives You will create the geometry for Lathe-Lesson-1, and then generate a toolpath to machine the part on a CNC
Autodesk Inventor Design Exercise 2: F1 Team Challenge Car Developed by Tim Varner Synergis Technologies
Autodesk Inventor Design Exercise 2: F1 Team Challenge Car Developed by Tim Varner Synergis Technologies Tim Varner - 2004 The Inventor User Interface Command Panel Lists the commands that are currently
Create a Rubber Duck. This tutorial shows you how to. Create simple surfaces. Rebuild a surface. Edit surface control points. Draw and project curves
Page 1 of 24 Create a Rubber Duck This exercise focuses on the free form, squishy aspect. Unlike the flashlight model, the exact size and placement of the objects is not critical. The overall form is the
Panel. Chapter 16. Solar Car. A. Sketch. Step 1. Click File Menu > New, click Part and OK. B. Save as "PANEL". Step 1. Click File Menu > Save As.
Chapter 16 Solar Car Panel A. Sketch. Step 1. Click File Menu > New, click Part and OK. Step 2. Click Top Plane in the Feature Manager and click Sketch from the Content toolbar, Fig. 1. Step 3. Click Center
3 AXIS STANDARD CAD. BobCAD-CAM Version 28 Training Workbook 3 Axis Standard CAD
3 AXIS STANDARD CAD This tutorial explains how to create the CAD model for the Mill 3 Axis Standard demonstration file. The design process includes using the Shape Library and other wireframe functions
TRAINING GUIDE MILL-LESSON-FBM-1 FBM MILL AND FBM DRILL
TRAINING GUIDE MILL-LESSON-FBM-1 FBM MILL AND FBM DRILL Mastercam Training Guide Objectives Previously in Mill-Lesson-6 and Mill-Lesson-7 geometry was created and machined using standard Mastercam methods.
JSS. Ping Pong Ball. in the Feature Manager and click Sketch on the Context toolbar, Fig. 1. on the Sketch toolbar.
Chapter 18 JSS Ping Pong Ball A. Half Circle Sketch. Step 1. Click File Menu > New, click Part Metric and OK. Step 2. Click Front Plane in the Feature Manager and click Sketch on the Context toolbar, Fig.
Boat. Battery Holder AA
Chapter 9 Boat Battery Holder AA A. Front Extrude. Step 1. Click File Menu > New, click Part and OK. Step 2. Click Front Plane in the Feature Manager and click Sketch context toolbar, Fig. 1. Step 3. Click
Mastercam X6 for SolidWorks Toolpaths
Chapter 14 Spinning Top Mastercam X6 for SolidWorks Toolpaths A. Insert Handle in New Assembly. Step 1. Click File Menu > New, click Assembly and OK. Step 2. Click Browse in the Property Manager, Fig.
Autodesk Inventor - Basics Tutorial Exercise 1
Autodesk Inventor - Basics Tutorial Exercise 1 Launch Inventor Professional 2015 1. Start a New part. Depending on how Inventor was installed, using this icon may get you an Inch or Metric file. To be
Module 1: Basics of Solids Modeling with SolidWorks
Module 1: Basics of Solids Modeling with SolidWorks Introduction SolidWorks is the state of the art in computer-aided design (CAD). SolidWorks represents an object in a virtual environment just as it exists
Introduction to MasterCAM X4,7
Introduction to MasterCAM X4,7 Spring 2014 By Meung J. Kim, Ph.D., Professor Department of Mechanical Engineering Northern Illinois University 1 Preliminaries C-Plane: flat Construction plane that can
SOLIDWORKS 2016 and Engineering Graphics
SOLIDWORKS 2016 and Engineering Graphics An Integrated Approach Randy H. Shih SDC PUBLICATIONS Better Textbooks. Lower Prices. www.sdcpublications.com Powered by TCPDF (www.tcpdf.org) Visit the following
Section A Solids Grade E
Name: Teacher Assessment Section A Solids Grade E 1. Write down the name of each of these 3-D shapes, (i) (ii) (iii) Answer (i)... (ii)... (iii)... (Total 3 marks) 2. (a) On the isometric grid complete
Toolpaths for Boat. OptiRough and Finish Waterline. Step 8. Click OK in the Machine Group Properties, Fig. 2. Stock display Click corner to move arrow
Mastercam 2017 Chapter 33 Toolpaths for Boat A. Machine Type and Stock Setup. Step 1. If necessary, open your BOAT ROUND BOTTOM. Step 2. If necessary, display Toolpaths Manager. On the View tab click (Alt-O).
SolidWorks 2013 and Engineering Graphics
SolidWorks 2013 and Engineering Graphics An Integrated Approach Randy H. Shih SDC PUBLICATIONS Schroff Development Corporation Better Textbooks. Lower Prices. www.sdcpublications.com Visit the following
Glider. Wing. Top face click Sketch. on the Standard Views. (S) on the Sketch toolbar.
Chapter 5 Glider Wing 4 Panel Tip A. Open and Save As "WING 4 PANEL". Step 1. Open your WING BLANK file. Step 2. Click File Menu > Save As. Step 3. Key-in WING 4 PANEL for the filename and press ENTER.
Autodesk Fusion 360 Training: The Future of Making Things Attendee Guide
Autodesk Fusion 360 Training: The Future of Making Things Attendee Guide Abstract After completing this workshop, you will have a basic understanding of editing 3D models using Autodesk Fusion 360 TM to
Airplane Assembly. SolidWorks 10 ASSEMBLY AIRPLANE Page 9-1
Chapter 9 A. Insert Parts. Airplane Assembly Step 1. Click File Menu > New, click Assembly and OK. Step 2. Click Keep Visible in the Property Manager, Fig. 1. Step 3. Click Browse in the Property Manager,
Fig. 1. Fig. 1. on the Standard Views toolbar. SolidWorks ASSEMBLY AIRPLANE Page 8-1
Chapter 8 Airplane Assembly A. Insert Set of Parts. Step 1. Click File Menu > New, click Assembly and OK. Step 2. Click View Menu > Origins to display the origin. Step 3. Click Keep Visible in the Property
MASTERCAM WIRE TUTORIAL. June 2018
MASTERCAM WIRE TUTORIAL June 2018 MASTERCAM WIRE TUTORIAL June 2018 2018 CNC Software, Inc. All rights reserved. Software: Mastercam 2019 Terms of Use Use of this document is subject to the Mastercam End
TRAINING GUIDE MILL-LESSON-FBM-2 FBM MILL AND FBM DRILL
TRAINING GUIDE MILL-LESSON-FBM-2 FBM MILL AND FBM DRILL Mastercam Training Guide Objectives This lesson will use the same Feature Based Machining (FBM) methods used in Mill-Lesson- FBM-1, how ever this
The Villa Savoye ( ), Poisy, Paris.
Learning SketchUp Villa Savoye This tutorial will involve modeling the Villa Savoye by Le Corbusier Files needed to complete this tutorial are available in Mr. Cochran s Web Site The Villa Savoye (1929-1931),
CATIA V5 Parametric Surface Modeling
CATIA V5 Parametric Surface Modeling Version 5 Release 16 A- 1 Toolbars in A B A. Wireframe: Create 3D curves / lines/ points/ plane B. Surfaces: Create surfaces C. Operations: Join surfaces, Split & Trim
Module 4A: Creating the 3D Model of Right and Oblique Pyramids
Inventor (5) Module 4A: 4A- 1 Module 4A: Creating the 3D Model of Right and Oblique Pyramids In Module 4A, we will learn how to create 3D solid models of right-axis and oblique-axis pyramid (regular or
TOOLPATHS TRAINING GUIDE. Sample. Distribution. not for MILL-LESSON-4-TOOLPATHS DRILL AND CONTOUR
TOOLPATHS TRAINING GUIDE MILL-LESSON-4-TOOLPATHS DRILL AND CONTOUR Mill-Lesson-4 Objectives You will generate a toolpath to machine the part on a CNC vertical milling machine. This lesson covers the following
GETTING STARTED WITH MASTERCAM SOLIDS
GETTING STARTED WITH MASTERCAM SOLIDS June 2017 GETTING STARTED WITH MASTERCAM SOLIDS June 2017 2017 CNC Software, Inc. All rights reserved. Software: Mastercam 2018 Terms of Use Use of this document is
Trace Bitmap. Chapter 7. A. Page Size. Step 1. Click File Menu > New (Ctrl-N).
Chapter 7 Trace Bitmap Riverview Rams Sarasota High Booker High A. Page Size. Step 1. Click File Menu > New (Ctrl-N). Step 2. Set page size in the Property bar: Width to 3.2 Fig. 1 Height to 2 Step 3.
Getting Started with Mastercam Solids. March 2016
Getting Started with Mastercam Solids March 2016 Mastercam 2017 Solids Getting Started TERMS OF USE Date: March 2016 Copyright 2016 CNC Software, Inc. All rights reserved. Software: Mastercam 2017 Use
Catamaran A. Create Rectangle. Step 1. If necessary start a new Mastercam file, click New on the Quick Access Toolbar QAT (Ctrl-N).
Mastercam 07 Chapter 6 Catamaran A. Create Rectangle. Step. If necessary start a new Mastercam file, click New on the Quick Access Toolbar QAT (Ctrl-N). Step. On the Wireframe tab click Rectangle. Step
MASTERCAM DYNAMIC MILLING TUTORIAL. June 2018
MASTERCAM DYNAMIC MILLING TUTORIAL June 2018 MASTERCAM DYNAMIC MILLING TUTORIAL June 2018 2018 CNC Software, Inc. All rights reserved. Software: Mastercam 2019 Terms of Use Use of this document is subject
Verisurf X Verisurf Tools
Verisurf X Verisurf Tools Verisurf Software, Inc. Verisurf X Tools User Manual Preface This Reference Manual contains information protected by copyright and subject to change without notice. No part of
Autodesk Fusion 360: Model. Overview. Modeling techniques in Fusion 360
Overview Modeling techniques in Fusion 360 Modeling in Fusion 360 is quite a different experience from how you would model in conventional history-based CAD software. Some users have expressed that it
Exercise Guide. Published: August MecSoft Corpotation
VisualCAD Exercise Guide Published: August 2018 MecSoft Corpotation Copyright 1998-2018 VisualCAD 2018 Exercise Guide by Mecsoft Corporation User Notes: Contents 2 Table of Contents About this Guide 4
QUICK-START TUTORIALS
PUERMC02_0132276593.QXD 08/09/2006 06:05 PM Page 83 QUICK-START TUTORIALS Chapter Objectives Create two real 3D modeling projects, starting them from scratch. Know the difference between representing 3D
TUTORIAL 2. OBJECTIVE: Use SolidWorks/COSMOS to model and analyze a cattle gate bracket that is subjected to a force of 100,000 lbs.
TUTORIAL 2 OBJECTIVE: Use SolidWorks/COSMOS to model and analyze a cattle gate bracket that is subjected to a force of 100,000 lbs. GETTING STARTED: 1. Open the SolidWorks program. 2. Open a new part file.
Tutorial Second Level
AutoCAD 2018 Tutorial Second Level 3D Modeling Randy H. Shih SDC PUBLICATIONS Better Textbooks. Lower Prices. www.sdcpublications.com Powered by TCPDF (www.tcpdf.org) Visit the following websites to learn
METBD 110 Hands-On 13 Exploded Assembly
METBD 110 Hands-On 13 Exploded Assembly 1. Open the assembly file created in Hands-On 12. IMPORTANT: For consistent success, use ONLY the method shown in this handout!! 2. Select the View Manager Icon
Memo Block. This lesson includes the commands Sketch, Extruded Boss/Base, Extruded Cut, Shell, Polygon and Fillet.
Commands Used New Part This lesson includes the commands Sketch, Extruded Boss/Base, Extruded Cut, Shell, Polygon and Fillet. Click File, New on the standard toolbar. Select Part from the New SolidWorks
Parametric Modeling Design and Modeling 2011 Project Lead The Way, Inc.
Parametric Modeling Design and Modeling 2011 Project Lead The Way, Inc. 3D Modeling Steps - Sketch Step 1 Sketch Geometry Sketch Geometry Line Sketch Tool 3D Modeling Steps - Constrain Step 1 Sketch Geometry
Chapter 11 Solar Car Drawing
Chapter 11 Solar Car Drawing A. Insert Top and Side Views. Step 1. Click File Menu > New, click Drawing and OK. Step 2. Click Browse Step 3. Select your solar car assembly file and click Open. Step 4.
4 & 5 Axis Mill Training Tutorials. To order more books: Call or Visit or Contact your Mastercam Dealer
4 & 5 Axis Mill Training Tutorials To order more books: Call 1-800-529-5517 or Visit www.inhousesolutions.com or Contact your Mastercam Dealer Mastercam X Training Tutorials 4 & 5 Axis Mill Applications
Chapter 2 Parametric Modeling Fundamentals
2-1 Chapter 2 Parametric Modeling Fundamentals Create Simple Extruded Solid Models Understand the Basic Parametric Modeling Procedure Create 2-D Sketches Understand the Shape before Size Approach Use the
Tower Drawing. Learning how to combine shapes and lines
Tower Drawing Learning how to combine shapes and lines 1) Go to Layout > Page Background. In the Options menu choose Solid and Ghost Green for a background color. This changes your workspace background
Parametric Modeling. With. Autodesk Inventor. Randy H. Shih. Oregon Institute of Technology SDC PUBLICATIONS
Parametric Modeling With Autodesk Inventor R10 Randy H. Shih Oregon Institute of Technology SDC PUBLICATIONS Schroff Development Corporation www.schroff.com www.schroff-europe.com 2-1 Chapter 2 Parametric
Chapter 4 Feature Design Tree
4-1 Chapter 4 Feature Design Tree Understand Feature Interactions Use the FeatureManager Design Tree Modify and Update Feature Dimensions Perform History-Based Part Modifications Change the Names of Created
ME009 Engineering Graphics and Design CAD 1. 1 Create a new part. Click. New Bar. 2 Click the Tutorial tab. 3 Select the Part icon. 4 Click OK.
PART A Reference: SolidWorks CAD Student Guide 2014 2 Lesson 2: Basic Functionality Active Learning Exercises Creating a Basic Part Use SolidWorks to create the box shown at the right. The step-by-step