How to Install a new ICP Board for NEC The ICP Board and You.

Size: px

Start display at page:

Download "How to Install a new ICP Board for NEC The ICP Board and You."

Everett Austin
6 years ago
Views:

1 How to Install a new ICP Board for NEC The ICP Board and You. To begin you will need to connect to your projector with your NEC Communicator in order to back up your current configuration files if you are able to. If you already have the files backed up then you can skip down to the installation of the board its self. 1. Connect to the projector via the Communicator. Once you have entered your projectors IP address click OK. (NOTE: That the IP address of your projector may differ from the one used below.) 2. Once logged on select Mode. C:/Users/Apollyon/ /icp_board.html 1/48

2 3. Click on the SERVICE button, and blow enter the code 3151 and click OK C:/Users/Apollyon/ /icp_board.html 2/48

3 . 4. Click the Next Arrow C:/Users/Apollyon/ /icp_board.html 3/48

4 5. Click UPDATE button. C:/Users/Apollyon/ /icp_board.html 4/48

5 6. Click the TITLES Button C:/Users/Apollyon/ /icp_board.html 5/48

6 7. When the new window opens click YES. C:/Users/Apollyon/ /icp_board.html 6/48

7 8. When the Save As window opens click New Folder button. C:/Users/Apollyon/ /icp_board.html 7/48

8 9. When the new folder shows up name the folder after the theatre that is being worked on. Then double click on the folder you just created. (I.E. You are working on theatre number #1 then name your folder "Theatre01". The name is optional and has no bearing on the rest of the actions.) C:/Users/Apollyon/ /icp_board.html 8/48

9 10. Once in your new folder click the SAVE button in the lower right hand corner. C:/Users/Apollyon/ /icp_board.html 9/48

10 11. Once the TITLES are saved you need to save ALL CINEMA FILES. C:/Users/Apollyon/ /icp_board.html 10/48

11 12. When the new window opens click YES. C:/Users/Apollyon/ /icp_board.html 11/48

12 13. Once in your new folder click the SAVE button in the lower right hand corner. C:/Users/Apollyon/ /icp_board.html 12/48

13 14. Click on SET SETTINGS. C:/Users/Apollyon/ /icp_board.html 13/48

14 15. When the new window opens click YES. C:/Users/Apollyon/ /icp_board.html 14/48

15 16. Once in your new folder click the SAVE button in the lower right hand corner. C:/Users/Apollyon/ /icp_board.html 15/48

16 You are now done backing up your ICP boards configuration files. NEC ICP Board Install. 1. Be sure to shut down the projector properly, by pressing the power button, until the display panel reads Standby. 2. Turn off the power to the projector by tripping the breaker as well as white power switch. C:/Users/Apollyon/ /icp_board.html 16/48

17 3. All cables must be removed from there respective connectors on the side panel. 4. Using a phillips head screw driver, unscrew the phillips screws from the side panel. (NOTE: The screws will not come completely out of the side panel, they will remain lose but still attached.) C:/Users/Apollyon/ /icp_board.html 17/48

18 5. Using the security key unlock the side panel and pull forward, then lift up to remove. C:/Users/Apollyon/ /icp_board.html 18/48

19 6. Using your phillips screw driver, loosen the screws starting with the bottom panel. (NOTE: You will have to start at the bottom and move up the boards as they are interlocked, meaning that to take out the tip board you have to remove all boards below it.) C:/Users/Apollyon/ /icp_board.html 19/48

20 C:/Users/Apollyon/ /icp_board.html 20/48

21 Order boards must be removed in. C:/Users/Apollyon/ /icp_board.html 21/48

22 Removal of the SDI Board C:/Users/Apollyon/ /icp_board.html 22/48

23 Removal of ICP Board C:/Users/Apollyon/ /icp_board.html 23/48

24 7. Place the old ICP board face down on a clean table. (NOTE: Do not do this on the floor or carpet.) C:/Users/Apollyon/ /icp_board.html 24/48

25 8. Carefully unscrew the 3 phillips screws holding the face plate to the board. C:/Users/Apollyon/ /icp_board.html 25/48

26 C:/Users/Apollyon/ /icp_board.html 26/48

27 C:/Users/Apollyon/ /icp_board.html 27/48

28 9. Remove protective covering from board. C:/Users/Apollyon/ /icp_board.html 28/48

29 10. Set old board in a safe then, unwrap the new board and place it face down with the screw holes to the face plate. C:/Users/Apollyon/ /icp_board.html 29/48

30 11. Start by screwing in the middle screw first. Make note that the face plate screw harness should be on the underside of the board at the moment. C:/Users/Apollyon/ /icp_board.html 30/48

31 12. Place the protective covering on the board, making sure to line up the screw holes on both sides. C:/Users/Apollyon/ /icp_board.html 31/48

32 C:/Users/Apollyon/ /icp_board.html 32/48

33 13. Once the face plate has been secured to the board insert the board back into the proper slot of the projector. After the board is secured follow this process for all broads that were removed. C:/Users/Apollyon/ /icp_board.html 33/48

34 14. Now tighten all the lock screws on all the boards. C:/Users/Apollyon/ /icp_board.html 34/48

35 15. Replace the side panel locking it in place with the security key. C:/Users/Apollyon/ /icp_board.html 35/48

36 16. Tighten all the lock screws into the side panel. C:/Users/Apollyon/ /icp_board.html 36/48

To correct this log on to your NEC Communicator. Board Re-Marriage 1. Connect to the projector via the Communicator.

37 17. Once the side panel is locked, removed remove the security key and power on the projector. 18. Once powered on you will receive a message on the LED panel reading Physical Marriage. To correct this log on to your NEC Communicator. Board Re-Marriage 1. Connect to the projector via the Communicator. Once you have entered your projectors IP address click OK. (NOTE: That the IP address of your projector may differ from the one used below.) C:/Users/Apollyon/ /icp_board.html 37/48

38 2. Once logged on select Mode. C:/Users/Apollyon/ /icp_board.html 38/48

39 3. Click on the SERVICE button, and blow enter the code 3151 and click OK C:/Users/Apollyon/ /icp_board.html 39/48

40 . 4. Click the SETUP button. Then click the INSTALLATION button. Then click on the Re-Marriage button C:/Users/Apollyon/ /icp_board.html 40/48

41 5. In new window enter USA as the Login ID. Enter the word Nakasendou. (NOTE: Both words must be entered just as they are. They are case sensitive.) C:/Users/Apollyon/ /icp_board.html 41/48

42 C:/Users/Apollyon/ /icp_board.html 42/48

43 You are now done with the Re-Marriage. 6. Next you will need to put your configuration files bacon on your projector. Click the UPDATE button. C:/Users/Apollyon/ /icp_board.html 43/48

44 7. Uncheck the box next to SKIP MCGD FILES. C:/Users/Apollyon/ /icp_board.html 44/48

45 8. Select the file with the ' C ' at the end of the name. Then click OPEN. C:/Users/Apollyon/ /icp_board.html 45/48

46 9. Select the file with the ' T ' at the end of the name. Then click OPEN. C:/Users/Apollyon/ /icp_board.html 46/48

47 10. Select the file with the ' S ' at the end of the name. Then click OPEN. C:/Users/Apollyon/ /icp_board.html 47/48

48 You have now completed the setup of your new ICP Board. Restart the projector and have a good day. C:/Users/Apollyon/ /icp_board.html 48/48

Adding or Replacing a PCI Card

Adding or Replacing a PCI Card Caution There are static-sensitive electronics inside the unit. Before you handle any parts, make sure you are working at a static-controlled workstation and that you are properly grounded. Three PCI cards