Digitakt OS 1.06 Release Information
|
|
- Nathan Davis
- 6 years ago
- Views:
Transcription
1 Digitakt OS 1.06 Release Information Elektron Music Machines February 12, 2018 How to upgrade: Upgrading from within the OS Select SYSTEM in the SETTINGS menu, and then select OS UPGRADE. Send the SysEx firmware file to the Digitakt either using the MIDI In Port or the USB Port. When the update is done the unit will restart by itself. After some OS upgrades the bootstrap is also upgraded. This operation must not be aborted, so never turn the power off until the Digitakt tells you to reboot. Upgrading from the Early Startup Menu Hold down the [FUNC] button while powering on. This takes you to the Digitakt boot menu. Enter the OS UPGRADE mode by pressing the [TRIG 4] key. Send the SysEx firmware file to the Digitakt using the MIDI In Port. During the transfer a bar in the display shows the progress. When the update is done the unit will restart by itself, booting the new OS. After some upgrades the bootstrap is also upgraded, this upgrade is performed right after the first restart of the Digitakt, do not turn the power off during the upgrade. To transfer the SysEx file, Elektron recommend using either Elektron Transfer application or The Elektron C6 Tool. Downgrading the Digitakt OS is not supported, and is performed at own risk. User content may be lost. Should you experience any problems or find any bugs, please report to Elektron support: Enjoy! The Elektron development team 1 (7)
2 List of changes from OS 1.05 to 1.06 Changing the velocity parameter in the Retrig menu had no effect. (OS 1.05 Regression) Signal level with no overdrive was 6dB too low. (OS 1.05 Regression) In the sound manager, there would be a graphics error on the display when copying more sounds than the destination had room for. List of changes from OS 1.04 to 1.05 Improvements Sound pool is added to the project. It is now possible to use sound locks on sequencer steps. Previewing Sounds in the Sound browser temporarily disables the [FUNC] + [UP/DOWN] page scrolling. Encoder click sensitivity is adjusted for better usability. The Track level graphics is now differentiated from other volume parameters graphics. There is now an indication that tells if the user tries to load a sample which exceeds available RAM in size. The active track indicator now has inverted graphics. The active page name is shown in the title bar when changing pages. Added a new Storage view to see the used/total amount of memory and the number of projects, Sounds, and samples. The Storage view is available in the SYSTEM menu. LFO speed parameter snaps to powers of two. Added sysex dump functionality. Added warning when trying to load more samples than there are slots available. Allowed more headroom in the bit-crusher to improve audio quality. Main output had inverted polarity. The main output polarity has been reversed. The Sound browser would change the preview sound immediately when highlighting it in the list. The Sound browser now changes the preview sound only when you press [FUNC]+[YES]. LFO Depth parameter locks were sometimes lost when saving. Outgoing MIDI CC data from the FX parameter pages were under some circumstances sent to the wrong MIDI channel. 2 (7)
3 BPM fraction would sometimes be incorrectly displayed. The filter trig parameter had no effect. The filter envelope was always triggered by a note trig but never triggered by a lock trig. All patterns will be automatically upgraded to compensate for the changes introduced by this fix. Lock trigs affected the release timing of the amplitude envelope. Page LEDs would not be fully lit when expanding pattern length in the SCALE menu. MIDI sequencer would crash under certain circumstances. Selecting OS Upgrade while unit was playing audio would output a static high pitched tone. After nudging the tempo, the tempo would change to the value set in Global tempo mode, even if Pattern tempo was enabled. Consecutive clear/paste of parameter pages would not work as intended. Sample selector and modulation destination selector would flicker if they were changed at the same time as another parameter. Unit would sometimes freeze during the startup sequence. MIDI CC was not transmitted from the Master page. Tune and Note params would skip two octaves instead of one, when dialed with [FUNC] pressed. In some cases MIDI tracks would stop sending CC values. Holding down [FUNC]+[CLEAR] while in grid recording mode would rapidly toggle between undo and redo. NRPN was not received. When pressing [FUNC]+[TEMPO] Mute mode would get activated until [FUNC] was pressed again. Track sound name would not be updated after sound export. Sound list would not be closed after saving a sound. Note length when recording multiple Audio tracks (i.e when not in chromatic mode) would not work properly. The unit would freeze when having external clock and selecting OS Upgrade. Lock trigs would always affect the note value. List of changes from OS 1.03 to 1.04 The grid record mode can now be toggled also while in Chromatic mode. The chromatic keyboard now has an extended octave range when a MIDI track is active. General performance optimizations. Time-consuming operations such as loading / saving samples and projects are now faster. 3 (7)
4 The unit would sometimes crash when attempting to save the project via the Func + Save Proj key combination. In some rare situations, the unit could crash while loading/deleting/moving samples. Pattern / Bank selection could not be accessed when in Chromatic mode. Playing the higest possible chromatic note (+24 semitones) on an audio track via MIDI would cause a hanging note. If the MIDI Output CH setting was set to Trk Ch, the trig keys would incorrectly send notes to MIDI channel 1, regardless of the configured track channels. If a sample was loaded to more than one slot, only the first slot would have the correct sample length. List of changes from OS 1.02 to 1.03 Updated factory presets. In total there are now 32 patterns and 64 sounds. To install the factory presets you must perform a Factory Reset. WARNING: Factory reset overwrites Sound Bank A and Project 001. Metronome can be disabled/enabled using Func+PTN long press. Help text is shown when attempting to change a disabled MIDI parameter. Help text is shown when switching mute modes. The shortcut operations for saving/reloading patterns have been changed so they don t apply to the saved plus drive project. In order to save patterns to (or reload ditto from) the plus drive project you must now use the pattern menu. This means you can use the quick save/reload operations to work with the pattern in a way that s not destructive for the saved project. The operations will now also work for unsaved and write-protected projects. New default MIDI settings for new projects: USB output is enabled and parameter output is set to CC. Active mute mode (global vs pattern) is now remembered, so that both the mute mode and the quick mute mode shows last visible mode instead of always defaulting to global mutes. Write-protected samples are now marked with a padlock in the sample manager. On/off switch-type trig parameters retain their names on screen when parameter locking. Were previously replaced by the text on or off. Improved bank selection mode. 4 (7)
5 Exception error when loading/deleting/moving samples. FX Settings not remembered after reboot. FX settings not applied correctly after pattern reload Track levels not applied after pattern reload. Having any MIDI track active causes internal tracks to ignore external MIDI notes. Changing to a Pattern in a different Bank while playing displays incorrectly. Pattern selection would go away before PTN button was released. Project sub-menus not restored properly when toggling settings menu. Not possible to edit or record trigs via USB MIDI auto channel. Pattern paste and pattern reload wouldn t update tempo. Clearing the trig page would incorrectly reset the note length. Zooming on the recorder screen could cause big delays when saving the sample. MIDI transport input ignored its designated setting, and would be received or not depending on whether clock input was enabled. Applying minimum trim in the recorder screen would make the unit freeze. Power cycling the unit would preserve the currently active global mutes, with one exception: if track 16 was muted, all tracks were unmuted after a power cycle. Some messages in the sample manager would not be displayed. It was not possible to clear MIDI note locks using trig key + play/clear. Pressing TRK would not close pattern change mode. Pattern selection mode would exit once a pattern had been selected, even though the PTN key was still being pressed. Mute mode could not be opened when in step recording mode. Pattern mute on MIDI Track would not engage until next pattern loop, or until the second run of a pattern when changing pattern while the sequencer is stopped. The unit would hang very easily if there were any trigs on the MIDI tracks and if transport mode was changed quickly a few times in a row. List of changes from OS 1.01 to 1.02 Improved metronome menu. Improved quantization menu. 5 (7)
6 Recorded sample trim is automatically reset after saving. Added possibility to reset recorded sample trim using the NO key. Reversed recorder zoom knob direction. Added graphical representation of reverb shelving filter. Added graphical representation of reverb and delay HP- and LP-filters. Improved simulation of encoder detention. Last note in the external MIDI chromatic keyboard range was not playable. The mapped drum octave on external MIDI was too wide, triggering not 8 audio tracks, but also incorrectly triggering the first 4 MIDI tracks. External MIDI could not be used to enter notes into the sequencer. Having any MIDI track active caused internal tracks to ignore external MIDI notes. Unit would sometimes crash when synced to external MIDI clock. MIDI Notes were not cleared from trig when removing trig. MIDI Note2..4 were not included in copy/paste trigs, nor when rotating a track, nor with scale page copy/paste/clear. It was not possible to record chords into the MIDI sequencer via Chromatic Mode or external MIDI when live recording. List of changes from OS 1.00 to 1.01 Empty kit is initialized with eight default drum samples. Graphical amplitude envelope added to amp page. Graphical filter envelope and filter response plot added to filter page. Graphical MIDI note keyboard added to the MIDI trig page. The export sound operation no longer prompts for which track sound to use. It just uses the currently active track. Func+yes can be used to preview sounds (using the active track) in the sound browser. Sample file association was not saved with sound, unless the slot parameter was updated after the sample was loaded. 6 (7)
7 Sample loop position parameter had the wrong upper limit. Corrected to 120. Sound tag editor responded very slowly to input and did not use full screen. LFO trig flag was not enabled by default in new project. The clear kit option in the pattern menu would actually clear the sequence. No note-off was sent for infinite length MIDI notes when pressing stop. Entering MIDI notes outside of the valid range ( ) using offsets would result in undefined behavior. Showing all the parameter values of pages delay, reverb, and master by pressing and holding func+page key did not work. 7 (7)
Digitakt OS 1.07 Release Information
Digitakt OS 1.07 Release Information Elektron Music Machines March 9, 2018 How to upgrade: Upgrading from within the OS Select SYSTEM in the SETTINGS menu, and then select OS UPGRADE. Send the SysEx firmware
More informationDigitakt OS 1.10 Release Information
Digitakt OS 1.10 Release Information Elektron Music Machines June 29, 2018 How to upgrade: Upgrading from within the OS Select SYSTEM in the SETTINGS menu, and then select OS UPGRADE. Send the SysEx firmware
More informationAnalog Four/Keys OS 1.24C Release information
Analog Four/Keys OS 1.24C Release information Elektron Music Machines February 13, 2017 How to upgrade: Upgrading from within the OS Select OS UPGRADE in the GLOBAL MENU Send the SysEx firmware file to
More informationSH-2. PLUG-OUT Software Synthesizer Owner s Manual
SH-2 PLUG-OUT Software Synthesizer Owner s Manual Copyright 2014 ROLAND CORPORATION All rights reserved. No part of this publication may be reproduced in any form without the written permission of ROLAND
More informationUser Guide. English. Manual Version 1.0
User Guide English Manual Version 1.0 Table of Contents (Click a chapter/section to skip to it.) Introduction... 5 Box Contents... 5 Support... 5 About This User Guide... 5 Initial Setup... 6 1. Software/Driver
More informationMOOG SUB 37 - FIRMWARE UPDATE UPDATE INSTRUCTIONS FOR WINDOWS (Skip to the next section for Mac OSX instructions)
MOOG SUB 37 - FIRMWARE UPDATE 1.2.0 WHAT YOU WILL NEED A computer A program for sending MIDI SysEx data to your Sub 37. We recommend Bome SendSX for Windows, or SysEx Librarian for Macintosh. DOWNLOAD
More informationAnalog Four/Keys OS 1.35B Release information
Analog Four/Keys OS 1.35B Release information Elektron Music Machines September 14, 2018 How to upgrade: Upgrading from within the OS Select OS UPGRADE in the GLOBAL SETTINGS menu. Send the SysEx firmware
More informationDigitakt. Beat making powerhouse. User Manual
Digitakt Beat making powerhouse User Manual FCC compliance statement This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause
More informationStepPolyArp Unit. Step Polyphonic Arpeggiator / Sequencer App & Audio Unit MIDI effect for ios
StepPolyArp Unit Step Polyphonic Arpeggiator / Sequencer App & Audio Unit MIDI effect for ios Presentation... 1 Application setup... 2 MIDI connections between ios applications... 2 MIDI over WiFi on macos...
More informationAmpliFIRE 6.0 Release Notes for AmpliFIRE, AF6 & AF12
AmpliFIRE 6.0 Release Notes for AmpliFIRE, AF6 & AF12 This firmware and editor have been tested rigorously both internally and by our beta team. As always, however, it is HIGHLY recommended that you back
More informationDigitakt. Beat making powerhouse. User Manual
Digitakt Beat making powerhouse User Manual FCC compliance statement This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause
More informationHALion 4. Version history Known issues & solutions. Januar 2013 Steinberg Media Technologies GmbH
HALion 4 Version history Known issues & solutions Januar 2013 Steinberg Media Technologies GmbH Table of contents About... 3 HALion 4.5.4... 4 Issues resolved... 4 HALion 4.5.3... 5 Improvements... 5 Issues
More informationx0xb0x Bassline Synthesizer ( Sokkos OS ) User Manual
x0xb0x Bassline Synthesizer ( Sokkos OS 1.9.1 ) User Manual Contents Synthesizer Section 1. Knobs, buttons & LED s 1.1 Function knob 1.2 Bank knob 1.3 Tempo knob & LED 1.4 Bank LED s 1.5 Buttons & LED
More informationQUICK-START GUIDE ROLAND DJ-808
QUICK-START GUIDE ROLAND DJ-808 Installation and Setup The Roland DJ-808 requires drivers for both Windows and MacOS operating systems. IMPORTANT NOTE: Please ensure you have the latest available drivers
More informationAxiom. User Guide. English
Axiom User Guide Table of Contents.......................................................................... 3 Introduction...................................................................... 3 What
More informationUser Manual. Drum Machine
User Manual Drum Machine Overview Interface Overview Interface 1 Nithonat s interface is split into three parts: Internal sequencer Responsible for editing patterns in Int.Seq. mode. Internal sequencer
More informationOctatrack DPS-1 OS 1.30C Release information
Octatrack DPS-1 OS 1.30C Release information Elektron Music Machines November 20, 2017 IMPORTANT: SECURE YOUR PROJECT TO COMPACT FLASH CARD USING PROJECT CARD SYNC BEFORE UPGRADING AND RESTORE IT USING
More informationTB-303. Software Bass Line Owner s Manual Roland Corporation 01
TB-303 Software Bass Line Owner s Manual 2019 Roland Corporation 01 Introduction For details on the settings for the DAW software that you re using, refer to the DAW s help or manuals. About Trademarks
More informationProcussion operation manual Basic Operation 15 BASIC OPERATION
Basic Operation 15 BASIC OPERATION 16 Main Controls 17 BASIC OPERATION MAIN CONTROLS MIDI ACTIVITY EDIT MENU SELECT CURSOR CONTROL VOLUME CONTROL I/O MASTER EDIT ENTER C01 Vol127 Pan=K CURSOR DATA VOLUME
More informationDrum Machine Manual V1.2.0
Drum Machine Manual V1.2.0 Rugged Circuits and Wusik Dot Com 2011 Welcome to Beat707 Arduino Shield This board requires an Arduino Board plugged on the bottom of the Beat707, you can also use a NetDuino
More informationnativekontrol PXT-Live Plus User Manual Version 1.0.8
nativekontrol PXT-Live Plus User Manual Version 1.0.8 1 CHANGES IN THIS VERSION 2 GENERAL OVERVIEW 3 SETUP 3.1 Live Settings 3.2 UserPlusPreferences 4 GLOBAL CONTROLS 4.1 Touch Strip 5 PLUS MATRIX MODES
More informationAxiom DirectLink for Reason and Record User Guide
User Guide Legal Notices This guide is copyrighted 2010 by Avid Technology, Inc., with all rights reserved. Under copyright laws, this guide may not be duplicated in whole or in part without the written
More informationUser Guide English. Manual Version 1.0
User Guide English Manual Version 1.0 Table of Contents Welcome to the MPC... 5 System Requirements and Product Support... 5 About This Manual... 6 Important Notes... 7 Installation... 7 MPC Hardware Overview...
More informationDigitone. Master of the digital method. User Manual
Digitone Master of the digital method User Manual FCC compliance statement This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may
More informationSystem Version February 14, 2017
KRONOS 61/73/88 KRONOS X 61/73/88 KRONOS 2 61/73/88/PLATINUM/LS/GOLD System Version 3.1.2 February 14, 2017 Changes Since KRONOS System Version 3.1.1 Disk mode In system version 3.1.1 only, when installing
More informationEasyStart. EMX1 Main Features. EasyStart CONTENTS
EasyStart EMX1 Main Features ValveForce Technology adds tube warmth using two 12AX7 tubes with a separate gain knob. MMT Technology with 16 different types of synthesis for totally new and dynamic sounds.
More informationWelcome to NEO Software Release Version
Welcome to NEO Software Release Version 3.8.2.97 Philips Strand Lighting has released a new version of software for the NEO lighting control family of products. This software, version 3.8.2.97 is available
More informationAnalog Rytm OS 1.45B Release Information
Analog Rytm OS 1.45B Release Information Elektron Music Machines September 14, 2018 How to upgrade: Upgrading from within the OS Select SYSTEM in the GLOBAL MENU, and then select OS UPGRADE. Send the SysEx
More informationAeolian Meditation. User Manual. All that we see or seem is but a dream within a dream. - Edgar Allan Poe
Aeolian Meditation User Manual All that we see or seem is but a dream within a dream. - Edgar Allan Poe The ultimate soundscape generator. Pure and meditative or an alien landscape. Ocean waves or an industrial
More informationHardware Control Reference
Hardware Control Reference Disclaimer The information in this document is subject to change without notice and does not represent a commitment on the part of Native Instruments GmbH. The software described
More informationFRONT PANEL OVERVIEW...1 REAR PANEL OVERVIEW...3 HOOKUP DIAGRAM...4 DISPLAYING INFORMATION...6
TABLE OF CONTENTS FRONT PANEL OVERVIEW...1 REAR PANEL OVERVIEW...3 HOOKUP DIAGRAM...4 DISPLAYING INFORMATION...6 OCTAVE AND TRANSPOSITION...6 NOTE...6 NOTE AFTERTOUCH (Channel Pressure)...6 CONTROL CHANGE...6
More informationBeatMaker 3 User Manual. Revision:
BeatMaker 3 User Manual Revision: 3.0.10 What s new in version 3.0.10 of this manual - Updated section Quick Start Guide: 1.3 Transport toolbar - Added section Performance View: 2.7 Select mode - Updated
More informationMixman StudioXPro QUICK REFERENCE GUIDE
Mixman StudioXPro QUICK REFERENCE GUIDE THE CONTROL ROOM 1 Control Room Audio Meter Lights Mix name / Megs Display Go to Remixing Studio Go to Editing Studio Loaded Single Single Auto-Loader Go to Recording
More informationMPC1000 & MPC2500 JJ OS128XL OPERATIONS MANUAL
MPC1000 & MPC2500 JJ OS128XL OPERATIONS MANUAL This manual is written only about the function added by JJ OS. Please refer to the manual of AKAI for the basic function of MPC. When you change OS, please
More informationMIDISynth-Control 1.0.6
MIDISynth-Control 1.0.6 https://itunes.apple.com/us/app/midisynth-control/id1366849280 http://www.sigabort.co/msc_android_demo.html Table of Contents 1 Overview... 4 1.1 Requirements... 4 1.1.1 ios...
More informationCrazy8 User Manual Mar 2017
Crazy8 User Manual Mar 2017 Welcome! Welcome to Crazy8, your crazy companion to handle all your sequencing needs! Be sure to check out the walkthrough videos on the Crazy8 page Twisted-electrons.com/crazy8
More informationTracktion Shortcut Keys
Tracktion Shortcut Keys General Flip between edit/project screens Go to project screen Go to edit screen Go to settings screen escape, ctrl + tab F1 F3 F2 Show colour-scheme editor window Save the current
More informationMV-8000 Production Studio. When asked So what s up with the new MV-8000? Here are the opening points to hit The MV-8000 has:
The Main Points When asked So what s up with the new MV-8000? Here are the opening points to hit The MV-8000 has: Integrated Sampling, MIDI Sequencing, and Audio Recording 2 Samplers In One High Quality
More informationScythe Synthesizer for iphone
Scythe Synthesizer for iphone http://www.bitmaskstudio.com/ https://twitter.com/bitmaskstudio Scythe is a polyphonic wavetable synthesizer which can load custom sounds and has a Wavetable Creator tool.
More informationDER OTO. With this firmware revision, you can use your Biscuit as a standard one (Revision 1.2) or as Der OTO.
User Manual Rev 2.3 February 2012 1 DER OTO PRESENTATION Der OTO is the new Biscuit firmware (revision 2) and turns your Biscuit into a monophonic synth. You can play Der OTO with a standard MIDI keyboard,
More informationCV.OCD USER MANUAL. CV.OCD has four assignable continuous analog CV outputs and twelve assignable gate/trigger outputs. MIDI-TO-CV
six4pix.com/cvocd CV.OCD USER MANUAL Introduction CV.OCD is a device which converts MIDI signals to the Control Voltage (CV) and Trigger/Gate signals which are used to control traditional analog synthesizers.
More informationUser Manual V
By User Manual V1.0 http://polyversemusic.com/support support@polyversemusic.com Gatekeeper User Manual Table of Contents Getting Started 4 Installation 4 Presets 5 With or Without MIDI? 5 Ableton Live
More informationNeutron Firmware Update Version (10 December 2018)
Neutron Firmware Update Version 2.0.0 - (10 December 2018) New Features Added full support for the Neutron Application. For more details please see the updated User Manual. Added Restore Default Parameters
More informationDMPro Midi Sysex Specification v /25/99
DMPro Midi Sysex Specification v. 1.00 01/25/99 This document contains the system exclusive documentation for the DMPro SYSTEM EXCLUSIVE FORMAT...2 OPCODE SUMMARY:...2 OPCODES:...3 00h - MIDI User Drum
More informationOperating System Version 2.0
Operating System Version 2.0 MAN0010079 E 4 2 KORG Pa300 Operating System release 2.0 New functions of OS Version 2.0 KORG Pa300 Operating System release 2.0 New functions of OS Version 2.0 Functions added
More informationDX PATCH LIBRARY MANUAL
DX PATCH LIBRARY MANUAL Firmware Version 2.03 CONNECTIONS Connect the DXPL as follows: USB POWER If using the USB cord for power, connect to an appropriate USB compliant (5V) power source. This could be
More informationLiveProfessor 2. User Manual. Rev audiostrom.com
LiveProfessor 2 User Manual Rev 1.0 - audiostrom.com Contents Introduction 4 System Requirements 4 License files 4 First Run 5 Installing Plugins Plugin Manager Audio Settings MIDI Inputs 7 Replacing A
More informationMPC Essentials Release Notes
MPC Essentials Release Notes About Akai Professional is continually updating and enhancing MPC Essentials. This document lists the new features, fixes and improvements made to your MPC Essentials software.
More informationAnalog Rytm OS 1.40C Release Information
Analog Rytm OS 1.40C Release Information Elektron Music Machines March 7, 2018 How to upgrade: Upgrading from within the OS Select SYSTEM in the GLOBAL MENU, and then select OS UPGRADE. Send the SysEx
More informationGroove Agent 4. Version history Known issues & solutions. Januar 2015 Steinberg Media Technologies GmbH
Groove Agent 4 Version history Known issues & solutions Januar 2015 Steinberg Media Technologies GmbH Table of contents Table of contents... 2 About... 3 Groove Agent 4.2.0... 4 New features... 4 Last
More informationUser Guide. English ( 3 16 ) Appendix English ( )
User Guide English ( 3 16 ) Appendix English ( 17 19 ) USB SUSTAIN C17 POWER ON OFF User Guide (English) Box Contents Oxygen 25 USB Cable Ableton Live Lite Software Download Card Quickstart Guide Safety
More informationPortable Music Studio
Everything you need, all in one. いつでも どこでも 作曲 Instruction Manual (08-2018) Portable Music Studio 1 Contents Features... 3 Basic Controls...4 - Menus and saving.. 5 Pattern Mode... 6 Global Pattern Settings...7
More informationMinimum Requirements. Installation & Release Notes. 1 Axe-Edit 3.0 Getting Started Axe-Edit 3.0 Getting Started. Mac Minimum Requirements
Welcome to Axe-Edit 3.0, the official software editor for the Fractal Audio Systems Axe-Fx II. Re-written from the ground up, version 3.0 is stable, reliable, and easily able to keep pace with future updates.
More informationCZPL PATCH LIBRARY OWNER S MANUAL
CZPL PATCH LIBRARY OWNER S MANUAL Firmware Version 4.05 This manual is a complete guide to using your CZPL for the Casio CZ series. Your CZPL is also a fully functional PL88 Universal Patch Library. For
More informationWaves GTR3 ToolRack Manual
Waves GTR3 ToolRack Manual Waves GTR ToolRack Manual 1 TABLE OF CONTENTS CHAPTER 1 INTRODUCTION...3 1.1 WELCOME...3 1.2 PRODUCT OVERVIEW...3 1.3 COMPONENTS...4 1.4 AUTOMATION...4 MIDI Automation...4 CHAPTER
More informationOwner s Manual. Copyright 2017 ROLAND CORPORATION
Owner s Manual Before using this unit, carefully read USING THE UNIT SAFELY and IMPORTANT NOTES (Startup Guide). After reading, keep the document(s) where it will be available for immediate reference.
More informationZETAOHM FLXS1. USER MANUAL v16d 10/13/17
ZETAOHM FLXS1 USER MANUAL v16d 10/13/17 Photo by Kurt Kurasaki 2017 TABLE OF CONTENTS TABLE OF CONTENTS 2 I. Front Panel Layout 3 II. Features 4 III. Menus 5 1. Accessing Menus 5 IV. Tempo Menu 8 V. Saving
More informationMIDISynth-Circuit User Guide
MIDISynth-Circuit 1.2.3 User Guide http://isotonikstudios.com/novation-x-isotonik/circuit-editor-vst-au/ http://sigabort.co/midisynth.html Table of Contents 1 Overview... 5 1.1 Requirements... 5 1.2 Limitations...
More informationOperation Manual. 1 Introduction to Geist2. Browser. Slicing. Sampler. 5 Pads and Layers. 6 Engines and Global Mixer. Geist2
2 Operation Manual 1 Introduction to 4 1.1... Architecture and Interface 5 1.2 Loading... sounds for the first time 10 1.3 Playing... pads and recording a pattern 13 1.4 Slicing... loops 17 1.5 More...
More informationUser Guide English. Manual Version 1.8
User Guide English Manual Version 1.8 Table of Contents Welcome to the MPC... 12 System Requirements and Product Support... 12 About This User Guide... 13 Important Notes... 14 Installation... 14 Windows...
More informationWorkshop. Automation ÂØÒňΠMV-8000
ÂØÒňΠMV-8000 Workshop Automation 2006 Roland Corporation U.S. All rights reserved. No part of this publication may be reproduced in any form without the written permission of Roland Corporation U.S.
More informationBitbox User s Manual
Bitbox User s Manual Welcome to bitbox. Bitbox is a very useful tool for capturing and playing back samples. This manual will walk you through all of the features of bitbox. If you want to start playing
More informationMIDISynth-Circuit Tablet/Phone User Guide
MIDISynth-Circuit Tablet/Phone 1.2.9 User Guide http://sigabort.co/midisynth_circuit_ios.html http://sigabort.co/midisynth_circuit_android.html Table of Contents 1 Overview... 4 1.1 Requirements... 4 1.1.1
More informationProphet Rev2 OS Addendum
Prophet Rev2 OS 1.1.4 Addendum Rev2 OS version 1.1.4 adds a number of new features not covered in the main Operation Manual. These features are described in this addendum in the order shown below. New
More informationDocumentation Addendum (Covers changes up to OS v1.20)
Fusion Documentation Addendum (Covers changes up to OS v1.20) This page is intentionally left blank. About this Addendum: The Fusion s operating system is upgradeable and allows us to add features and
More informationHALion 5. Version history Known issues & solutions. February 2015 Steinberg Media Technologies GmbH
HALion 5 Version history Known issues & solutions February 2015 Steinberg Media Technologies GmbH Table of contents Table of contents... 2 About... 3 HALion 5.1.10... 4 Improvements & issues resolved...
More informationSMARTClock Gen3. User Manual
SMARTClock Gen3 User Manual 2 of 9 Revision History: vbeta4 reworked MIDI thru settings added INT interface mode vbeta3 vbeta2 Initial Release SMARTClock Gen3 Quick Start 3 of 9 Thanks for purchasing a
More informationFaderPort 8 8-channel Production Controller
FaderPort 8 8-channel Production Controller www.presonus.com English Table of Contents 1 Overview 1 1.1 Introduction 1 1.2 About this manual 1 1.3 FaderPort 8 Features 2 1.4 Studio One Artist Features
More informationStereo Triggered Sampler 4ms Company
Stereo Triggered r 4ms Company New features in Firmware v1.4 October 26, 2017 (Addendum to User Manual 1.0: http://4mscompany.com/sts/sts-manual-1.0.pdf) Table of Contents: Introducing firmware 1.4 1 What
More informationCubase 9.5. Version History. October 2018 Steinberg Media Technologies GmbH
Cubase 9.5 Version History October 2018 Steinberg Media Technologies GmbH Cubase 9.5.40 Issues & improvements The following list details resolved issues and improvements in this version. Additional improvements
More informationMCS3 USB Software for OSX
MCS3 USB Software for OSX JLCooper makes no warranties, express or implied, regarding this software s fitness for a particular purpose, and in no event shall JLCooper Electronics be liable for incidental
More informationUser Manual. Manual Sections. Download a PDF version of the manual here: carbon-manual.pdf
CARBON User Manual Download a PDF version of the manual here: carbon-manual.pdf Manual Sections Introduction Precautions Getting Started User Interface Sequencer Song Mode Arpeggiator Loading and Saving
More informationHALion 6 HALion Sonic (SE) 3
HALion 6 HALion Sonic (SE) 3 Version history June 2017 Steinberg Media Technologies GmbH HALion 6.0.10 / HALion Sonic (SE) 3.0.10 Improvements & issues resolved The following lists all resolved issues
More informationOPERATION MANUAL VST / AU
OPERATION MANUAL VST / AU This manual is under construction. If you want to help to improve it contact: info@audiorealism.se Introduction AudioRealism Bass Line 3 (ABL3) is an emulation of a classic pattern
More informationGroove Agent 4. Version history Known issues & solutions. April 2016 Steinberg Media Technologies GmbH
Groove Agent 4 Version history Known issues & solutions April 2016 Steinberg Media Technologies GmbH Table of contents About... 3 Groove Agent 4.2.30... 4 Improvements & issues resolved... 4 Groove Agent
More informationChapter 3 User Interface Basics
Chapter 3 User Interface Basics Mode Buttons Navigation The Display Chapter 3 will show you how to get around the front panel of your K2500. Your interactions can be divided into three primary operations:
More informationPT210M: Contents. Preface... xi Lesson 1. Preparing The Session... 1
PT210M: Contents Preface... xi Lesson 1. Preparing The Session... 1 Customizing Sessions with MIDI Setup... 2 MIDI Connections to Pro Tools... 2 MIDI Studio Setup (Windows Only)... 3 Audio MIDI Setup (Mac
More informationLIQUID FOOT+ SERIES MIDI FOOT CONTROLLERS. FIRMWARE PLATFORM V6.00beta. This documentation will be updated
LIQUID FOOT+ SERIES MIDI FOOT CONTROLLERS FIRMWARE PLATFORM V6.00beta This documentation will be updated REV 1.0 - NOV 3, 2018 Table of Contents V6.00 BETA FIRMWARE INSTALLATION NOTES... 3 V6.00 System
More informationUser Guide. FingerBeat 2.0. manual version 1.1
User Guide FingerBeat 2.0 manual version 1.1 1 Dear Friend, Thank you for downloading & supporting our work. FingerBeat is an easy to use pocket sampler, drum machine designed for intuition and creative
More informationUsing BOSS TONE STUDIO for SY-300
This document explains operation of BOSS TONE STUDIO for SY-300 (subsequently referred to as TONE STUDIO ). Getting Ready to Use TONE STUDIO Important terms in TONE STUDIO Library This is a storage area
More information000 How to Use this Book... 11
Table of Contents 000 How to Use this Book... 11 Which MPCs are compatible with this book?... 11 Hardware UI Vs Computer UI... 11 Recreating the Tutorial Examples... 11 Reading This Book On Mobile Devices...
More informationINSTALLATION. UNDERSCORE is a sample library for Native Instruments Kontakt 5.3 and later. It will NOT work with the free Kontakt Player.
INSTALLATION UNDERSCORE is a sample library for Native Instruments Kontakt 5.3 and later. It will NOT work with the free Kontakt Player. Before loading any of the instruments in the Instruments folder,
More informationMIDIPLUS Co, Ltd.
MIDIPLUS Co, Ltd. http://www.midiplus.com.tw CONTENTS Preface... 1 What s in the Box?... 1 O62 Keyboard Overview... 1 Chapter 1:Quick Start... 2 1.1 O62 Overview... 2 1.1.1 Front panel Overview... 2 1.1.2
More informationBass Station II v4.14 New Features User Guide
Bass Station II v4.14 New Features User Guide New Features: AFX Mode Fixed-Duration Sustain Envelopes Envelope Retrigger Count Glide Divergence Extended Sub-Oscillator Tuning 1 CONTENTS AFX Mode... 3 Overlays...
More informationnativekontrol MXT-Live User Manual Version 1.0.5
1 CHANGES IN THIS VERSION 2 GENERAL OVERVIEW 3 SETUP 3.1 Live Settings 3.2 UserPreferences 4 LAYOUT OVERVIEW 5 GLOBAL CONTROLS 5.1 Upper Left Buttons 5.2 Master Section 5.3 Groups Section 5.4 Transport
More informationRHIZOME HOST USER GUIDE V 2.1
o RHIZOME HOST USER GUIDE V 2.1 1. INTRODUCTION... 5 2. UNIT WORKFLOW... 6 2.1. Displays... 6 2.2. Matrix Edit... 6 2.3. Transport bar... 7 2.4. Common function buttons... 8 2.5. Left zone white printed
More informationGotharman s FuZioN. Music WorkStation. User Manual V 10.60
Gotharman s FuZioN Music WorkStation User Manual V 10.60 Contents Of This Manual Introduction 5 Very special thanks to 7 Getting Started 8 Structure 14 User Interface 16 Preset Select Screen 19 Synth Triggers
More informationReason Remote support for Mackie control surfaces
Reason Remote support for Mackie control surfaces This document describes the Remote implementation for Mackie Control, Extender and C4. For general information about how to use Remote in Reason, please
More informationIntroduction. SYNFERNO is a powerful instrument and cinematic sound module for the NATIVE INSTRUMENTS KONTAKT 5 sampler.
Table of contents Introduction...3 Sytem Requirements...4 Installation.....5 Launching SYNFERNO...6 Playing Loops...8 GUI Overview...10 The EDIT Page...12 The FX Page...14 The SEQ Page...17 MIDI Mapping
More informationUsing BOSS TONE STUDIO for ME-80
This document explains operation of BOSS TONE STUDIO for ME-80 (subsequently referred to as TONE STUDIO ). Getting Ready to Use TONE STUDIO Important terms in TONE STUDIO Library This is a storage area
More informationAppendix 1: Upgrading the system software
THE APPENDICES A.1 THE APPENDICES Appendix 1: Upgrading the system software Infection Music strongly recommends that you read through this section before you attempt to perform any kind of software upgrade.
More informationEM-1 Main Features. EasyStart CONTENTS
EasyStart EM-1 Main Features Pattern performance with emphasis on realtime operation All functions are right on the surface, with no menus or pages to slow you down! Familiar 16-step key interface to build
More informationSD7 - Update Half Bar Tempo accelerando/ritardando Step Lower Limit Upper Limit
SD7 - Update 1.3.0 Half Bar Added this function: if pressed during the first half of the measure, the 1/2 bar fill is heard during the current measure. However if pressed during the 2 nd half of the measure,
More informationUser Manual. for ArcTrax UWP version
User Manual for ArcTrax UWP version 1.0.3.0 Table of Contents 1 Overview... 2 1.1 Introduction... 2 1.2 Structure... 2 2 Panel Reference... 3 2.1 Overview... 3 2.2 Controls... 4 2.3 Oscillator... 5 2.4
More informationMainStage 2. Exploring MainStage
MainStage 2 Exploring MainStage KKApple Inc. Copyright 2011 Apple Inc. All rights reserved. Your rights to the software are governed by the accompanying software license agreement. The owner or authorized
More informationVirtualDJ 8 Pioneer DDJ-SR 1
VirtualDJ 8 Pioneer DDJ-SR 1 Table of Contents A. INSTALLATION... 3 Firmware & Drivers... 3 VirtualDJ 8 Setup... 3 Advanced Setup... 4 PAD PLUS mode... 4 B. MIXER... 5 C. DECKS... 7 D. EFFECTS... 9 E.
More informationChronotron - Change log
Chronotron - Change log Release 102 (2018-04-12): New: Voice commands. The list of supported commands can be found here Improved: Reduced latency in Hold mode Improved: Minor UI enhancements and bug fixes
More informationPSQ-1684 Operation Manual
PSQ-1684 Operation Manual Version 3.0.0 1 Table of Contents Table of Contents Introduction Quick Start Main Clock Section Run Sync & Rate Shuffle Reset CV Reset CV Run Chaining PSQs Pulse Section Generator
More informationUser Guide. English. Manual Version 1.1
User Guide English Manual Version 1.1 Table of Contents Introduction... 4 Editing the Controls... 10 Information & Support... 4 Installation... 4 Overview... 10 Graphical User Interface... 10 Control Panel...
More informationLITTLE MIDI MACHINE v3.0
LITTLE MIDI MACHINE v3.0 Welcome to Little MIDI Machine! This little app will let you turn your ipad into a vintage analog-style step sequencer so that you can use your ipad to control your hardware synthesizers
More information