Dr. Beards Snake Oil Advertising Sign
|
|
|
- George Patterson
- 6 years ago
- Views:
Transcription
1 Dr. Beards Snake Oil Advertising Sign DOWNLOAD THE PATTERNS FOR THIS TOTORIAL HERE
2 Open Designer PRO Create a new project and set the dimensions to length = 24 width = 14
3 The workpiece will appear horizontally on the screen. Turn off the texture for best viewing. Then rotate the board 90 CW to orient the project as it will be viewed in real life.
4 Using the Rectangle Tool, place a 22 by 12 rectangle on the workpiece and Center it in both axes. Use the Carve Region tool and set the depth to be.125 deep.
5 Use the Feather tool to create a ½ bevel around the rectangle. Do not flip the feather when asked. Select the Text Tool and enter Dr. Beards in the text window. Select the Gloucester MT font (or similar), and make sure the carving mode is Raster. Select OK.
6 Right click on the highlighted text and Flip & Rotate it 90 CCW Scale the text to fit the width of the carved region and select the Edit Envelope tool.
7 In the bottom edit envelope window start by grabbing the two right corner red dots and move them up creating a parallelogram shape. Keep the end length roughly the same and near vertical. Next right click on the line bounding the top of the text and change its form to Spline.
8 Manipulate the spline control points (blue dots) to create a curve to the top line of the text box Do the same to line across the bottom of the text box
9 This an extremely powerful way to manipulate (or) morph existing elements into new and interesting shapes. This tool also works on patterns. Once happy with the new shape; click OK to proceed. The element can be returned to its original shape by clicking Reset at any point during the envelope modification. Back on the board view, use the yellow dot at the bottom of the text to stretch it vertically.
10 Now center the Text. Remember, we have everything rotated, so we will need to center it vertically instead of horizontally as it would seen looking at the screen. Next, select the Text tool again and type in Authentic using the same font as before. This time select Centerline carving mode and click OK.
11 Rotate the text 90 degrees CCW, scale it, and position it under the Dr. Beards text. Select the Edit Envelope tool and move the top right red dot up and move the top left dot slightly down. This gives the text a wedge shape. Click to proceed.
12 Scale the text to fit the space and click the Conform check box on the toolbar so that the text will be applied to the regions depth (and not at the board surface). Select Dr. Beards text again and apply a medium draft to it.
13 Open the pattern library and select the Poster Straight Banner. Place it on the workpiece with a click. Scale the banner pattern, reduce its depth to.125, center it on the board, give it a medium draft, and position it under the existing text.
14 Select the Text tool and type in SNAKE ELIXER using the Eccentric Std.(or similar) font. This time select Centerline carving mode and click OK. Rotate the text 90 degrees CCW, center it on the board, scale it to fit the banner, position it vertically on the banner, and fill the Conform check box on the toolbar.
15 Select the banner and the three instances of text using the Pointer tool or by selecting them individually in the Carving list. Right click on the selections and select Group. In the carving list you can now see the four elements grouped together. Click on the name Group and rename this group Masthead. Now that these elements are grouped, they can easily be moved together.
16 Open the pattern library and select the Poster Bottle. Place it on the workpiece with a click. Scale the bottle, reduce its depth to.125, center it on the board, give it a medium draft, and position it under the existing composition. Copy the Dr. Beards text by clicking on it and pressing the Ctrl and c keys simultaneously. Move the pointer and then press the Ctrl and v keys simultaneously. This can also be done in the Edit menu.
17 Scale the text to fit on the bottle label and position it near the top of the label. With the text still highlighted, select the Text icon and change the carving type to Centerline.
18 Fill the Conform check box on the toolbar so that it is placed on the background region. Create the second part of the bottle label by placing Original in Eccentric Std. (or similar) font. Rotate, center, position, centerline, bold and conform the text. You could also copy and paste the SNAKE ELIXER text and modify it accordingly.
19 Open the pattern library and select the Trunk Filigree 1. Place it on the workpiece with a click. Rotate the filigree, scale it to fit the label, reduce its depth to.100, center it on the board, give it a medium draft, and position it on the bottle label. Copy the filigree from the label and paste it above left of the bottle (you will have to remove the centering constraint if you use a copy). Increase its height to.125.
20 Scale and position the filigree relative to the bottle. Flip the filigree across the horizontal axis (remember we have rotated the board view). Mirror the filigree across the center of the board.
21 Copy the left filigree, paste it, move it to the upper left corner of the sign and Flip it across the vertical axis.
22 Select all of the elements of the bottle and Group them. Change the name of the group to Bottle.
23 Add centerline text at top and bottom of sign. Open the pattern library and select the Poster Vertical Banner Place it on the workpiece with a click. Scale the banner, reduce its depth to.125, reduce its height to 10, give it a medium draft, and position it left of the bottle.
24 Open the pattern library and select the Poster Curve Banner and Trunk Flower Rosette. Place them on the workpiece with a click. Scale, reduce depth to.125, assign medium draft, and position them left of the bottle. Mirror the three patterns just placed across the Horizontal axis.
25 Place centerline text in left banner. Place the Center Element pattern onto the right banner. Scale, reduce depth to.100, increase height to 999, assign medium draft, and position.
26 Place raster CURE ALL text. Rotate, scale, reduce depth to.125, increase height to 999, assign medium draft, and position. Select the Edit Envelope tool and change the bottom edge of the text box to an arc. The arc is in the wrong direction so right click and select Reverse Arc.
27 Tweak the arc radius and height of text to get the right look. Click OK. Stretch the box. Repeat for the BLEND text on the bottom side of the center element.
28 Move to the left banner to place centerline text. Select the Spline tool. Draw a three node spline along the bottom edge of the curved banner
29 Select the Decorate Text icon. Type in the text Tastes Good. Make sure the centerline mode is selected. Set the text size to 50 and the character spacing to 7. Modify the text and spline as needed and make sure that the Conform check box is filled.
30 Repeat the same steps for engraving the banner on the right side of the bottle to complete the composition.
This project covers the following design concepts:
Design Project 3 12 Winter Snowflake This project covers the following design concepts: STARTING SOFTWARE MENUS, TOOLBARS, SHORTCUT KEYS OR MOUSE BUTTONS MANIPULATING THE WORKPIECE SNAP TO GRID DRAWING
This project covers the following design concepts:
Design Project 4 This project covers the following design concepts: DRAWING TOOLS SNAP TO GRID SETTING CONSTRAINTS CUT PATH TOOL CENTERLINE TEXT COPY & PASTE CONFORMING VECTOR CREATING A CLOSED REGION
Generating Vectors Overview
Generating Vectors Overview Vectors are mathematically defined shapes consisting of a series of points (nodes), which are connected by lines, arcs or curves (spans) to form the overall shape. Vectors can
SketchUp Starting Up The first thing you must do is select a template.
SketchUp Starting Up The first thing you must do is select a template. While there are many different ones to choose from the only real difference in them is that some have a coloured floor and a horizon
StickFont Editor v1.01 User Manual. Copyright 2012 NCPlot Software LLC
StickFont Editor v1.01 User Manual Copyright 2012 NCPlot Software LLC StickFont Editor Manual Table of Contents Welcome... 1 Registering StickFont Editor... 3 Getting Started... 5 Getting Started...
Quick Crash Scene Tutorial
Quick Crash Scene Tutorial With Crash Zone or Crime Zone, even new users can create a quick crash scene diagram in less than 10 minutes! In this tutorial we ll show how to use Crash Zone s unique features
ADOBE TRAINING CS6 PHOTOSHOP BASICS: EDITING PHOTOS & WORKING WITH TEXT - 1
ADOBE TRAINING CS6 PHOTOSHOP BASICS: EDITING PHOTOS & WORKING WITH TEXT Photoshop is the leading professional software for editing and adjusting photos, images and other graphic projects. It is a very
Lesson 1: Creating T- Spline Forms. In Samples section of your Data Panel, browse to: Fusion 101 Training > 03 Sculpt > 03_Sculpting_Introduction.
3.1: Sculpting Sculpting in Fusion 360 allows for the intuitive freeform creation of organic solid bodies and surfaces by leveraging the T- Splines technology. In the Sculpt Workspace, you can rapidly
CO2 Rail Car. Wheel Rear Px. on the Command Manager toolbar.
Chapter 6 CO2 Rail Car Wheel Rear Px A. Sketch Construction Lines. Step 1. Click File Menu > New, click Part Metric and OK. Step 2. Click Front (plane) in the Feature Manager (left panel), Fig. 1. Step
Design Development Documentation
Design Development Documentation Preliminary Logo One For the first logo design in which I created I started off with a clipart image of a clenched fist in which I traced within Photoshop. I chose this
ILLUSTRATOR TUTORIAL-1 workshop handout
Why is Illustrator a powerful tool? ILLUSTRATOR TUTORIAL-1 workshop handout Computer graphics fall into two main categories, bitmap graphics and vector graphics. Adobe Illustrator is a vector based software
Working with PhotoVCarve files
Getting Started with Tutorial 4 Intermediate Level Working with PhotoVCarve files VCarve Pro Disclaimer All CNC machines (routing, engraving, and milling) are potentially dangerous and because Vectric
L E S S O N 2 Background
Flight, Naperville Central High School, Naperville, Ill. No hard hat needed in the InDesign work area Once you learn the concepts of good page design, and you learn how to use InDesign, you are limited
Photocopiable/digital resources may only be copied by the purchasing institution on a single site and for their own use ZigZag Education, 2013
SketchUp Level of Difficulty Time Approximately 15 20 minutes Photocopiable/digital resources may only be copied by the purchasing institution on a single site and for their own use ZigZag Education, 2013
Adobe Illustrator CS5 Part 2: Vector Graphic Effects
CALIFORNIA STATE UNIVERSITY, LOS ANGELES INFORMATION TECHNOLOGY SERVICES Adobe Illustrator CS5 Part 2: Vector Graphic Effects Summer 2011, Version 1.0 Table of Contents Introduction...2 Downloading the
Technique or Feature Where Introduced
Part 6: Keypad 4 Mirrored features Patterned features First extrusion Rounded corners In the earpiece part, you defined a radial pattern, one that created new instances of a feature at intervals around
Tutorial 1 Engraved Brass Plate R
Getting Started With Tutorial 1 Engraved Brass Plate R4-090123 Table of Contents What is V-Carving?... 2 What the software allows you to do... 3 What file formats can be used?... 3 Getting Help... 3 Overview
Real Estate Flyer. Projects 1
Projects 1 PagePlus provides a wide selection of design templates, which you can use as starting points for your own publications. In this project, we ll start with a real estate flyer template and customize
3ds Max Cottage Step 1. Always start out by setting up units: We re going with this setup as we will round everything off to one inch.
3ds Max Cottage Step 1 Always start out by setting up units: We re going with this setup as we will round everything off to one inch. File/Import the CAD drawing Be sure Files of Type is set to all formats
Photocopiable/digital resources may only be copied by the purchasing institution on a single site and for their own use ZigZag Education, 2013
SketchUp Level of Difficulty Time Approximately 15 20 minutes Photocopiable/digital resources may only be copied by the purchasing institution on a single site and for their own use ZigZag Education, 2013
H Stab and V Stab. Chapter 6. Glider. A. Open and Save as "H STAB". Step 1. Open your STABILIZER BLANK file.
Chapter 6 Glider H Stab and V Stab A. Open and Save as "H STAB". Step 1. Open your STABILIZER BLANK file. Step 2. Click File Menu > Save As. Step 3. Key-in H STAB for the filename and press ENTER. B. Sketch
Cudacountry Radial. Fig. 2. Point. Fig. 4. Mastercam 2017 Cudacountry Radial Page 19-1
Mastercam 2017 Chapter 19 Cudacountry Radial A. Create Rectangle. Step 1. If necessary start a new Mastercam file, click New QAT. (Ctrl-N) on the Quick Access Toolbar Step 2. On the Wireframe tab click
Corel Draw 11. What is Vector Graphics?
Corel Draw 11 Corel Draw is a vector based drawing that program that makes it easy to create professional artwork from logos to intricate technical illustrations. Corel Draw 11's enhanced text handling
How to draw and create shapes
Adobe Flash Professional Guide How to draw and create shapes You can add artwork to your Adobe Flash Professional documents in two ways: You can import images or draw original artwork in Flash by using
Paint Tutorial (Project #14a)
Paint Tutorial (Project #14a) In order to learn all there is to know about this drawing program, go through the Microsoft Tutorial (below). (Do not save this to your folder.) Practice using the different
SolidWorks Intro Part 1b
SolidWorks Intro Part 1b Dave Touretzky and Susan Finger 1. Create a new part We ll create a CAD model of the 2 ½ D key fob below to make on the laser cutter. Select File New Templates IPSpart If the SolidWorks
PART I GravoStyle5-Laser Introduction
PART I GravoStyle5-Laser Introduction I. INTRO GravoStyle 5 Laser is designed is a component of GravoStyle5 for use with the Gravograph/New Hermes and other manufacturer Laser Engravers. Combined with
Adobe Illustrator CC 2018 Tutorial
Adobe Illustrator CC 2018 Tutorial GETTING STARTED Adobe Illustrator CC is an illustration program that can be used for print, multimedia and online graphics. Whether you plan to design or illustrate multimedia
Tutorial 4: Texture Mapping Techniques
Tutorial 4: Texture Mapping Techniques Completion time 40 minutes In the previous tutorial we learned how to create materials, and how to assign texture maps to those materials. In this tutorial we will
Creating a T-Spline using a Reference Image
1 / 17 Goals Learn how to create a T-Spline using a Reference Image. 1. Insert an image into the workspace using Attach Canvas. 2. Use Calibrate to set the proper scale for the reference image. 3. Invoke
12 APPLYING EFFECTS. Lesson overview
12 APPLYING EFFECTS Lesson overview In this lesson, you ll learn how to do the following: Use various effects like Pathfinder, Distort & Transform, Offset Path, and Drop Shadow effects. Use Warp effects
Tutorial VCarving Christmas Decorations
Getting Started With Tutorial VCarving Christmas Decorations VCarve Pro Disclaimer All CNC machines (routing, engraving, and milling) are potentially dangerous and because Vectric Ltd has no control over
Tutorial 3: Constructive Editing (2D-CAD)
(2D-CAD) The editing done up to now is not much different from the normal drawing board techniques. This section deals with commands to copy items we have already drawn, to move them and to make multiple
2 Solutions Chapter 3. Chapter 3: Practice Example 1
1 Solutions This section includes the step by step solutions for the practice exercise for the following chapters and sections: Chapter 3 Chapter 4 Chapter 5 Chapter 11: Rainbow Springs sample test Final
Lesson 14 Blends. For Resources go to > click on the Creo Parametric Book cover
Lesson 14 Blends Figure 14.1 Cap OBJECTIVES Create a Parallel Blend feature Use the Shell Tool Create a Swept Blend REFERENCES AND RESOURCES For Resources go to www.cad-resources.com > click on the Creo
SolidWorks 2½D Parts
SolidWorks 2½D Parts IDeATe Laser Micro Part 1b Dave Touretzky and Susan Finger 1. Create a new part In this lab, you ll create a CAD model of the 2 ½ D key fob below to make on the laser cutter. Select
Creating a Title Block & Border Using Chief Architect. Architectural Design & Residential Construction Penncrest High School
Creating a Title Block & Border Using Chief Architect Architectural Design & Residential Construction Penncrest High School 2017-2018 Select New Layout to begin designing your Title Block. Note: Once the
SketchUp. SketchUp. Google SketchUp. Using SketchUp. The Tool Set
Google Google is a 3D Modelling program which specialises in making computer generated representations of real-world objects, especially architectural, mechanical and building components, such as windows,
Glider. Wing. Top face click Sketch. on the Standard Views. (S) on the Sketch toolbar.
Chapter 5 Glider Wing 4 Panel Tip A. Open and Save As "WING 4 PANEL". Step 1. Open your WING BLANK file. Step 2. Click File Menu > Save As. Step 3. Key-in WING 4 PANEL for the filename and press ENTER.
Module 1: Basics of Solids Modeling with SolidWorks
Module 1: Basics of Solids Modeling with SolidWorks Introduction SolidWorks is the state of the art in computer-aided design (CAD). SolidWorks represents an object in a virtual environment just as it exists
Ladybird Project - Vacuum Mould
- Vacuum Mould Prerequisite Mould drawn and saved as STL file from Solidworks Focus of the Lesson On completion of this exercise you will have completed: Opening STL file Setting Machining Constraints
Using the IDEF0 Diagram in Innoslate
Using the IDEF0 Diagram in Innoslate This document discusses how to use the IDEF0 Diagram in Innoslate. Contents IDEF0 Entities...2 IDEF0 Relationships...2 IDEF0 Interactions...3 Adding an Action...3 Adding
CS Multimedia and Communications REMEMBER TO BRING YOUR MEMORY STICK TO EVERY LAB! Lab 02: Introduction to Photoshop Part 1
CS 1033 Multimedia and Communications REMEMBER TO BRING YOUR MEMORY STICK TO EVERY LAB! Lab 02: Introduction to Photoshop Part 1 Upon completion of this lab, you should be able to: Open, create new, save
User Guide. for. JewelCAD Professional Version 2.0
User Guide Page 1 of 121 User Guide for JewelCAD Professional Version 2.0-1 - User Guide Page 2 of 121 Table of Content 1. Introduction... 7 1.1. Purpose of this document... 7 2. Launch JewelCAD Professional
CREATING THE FUNKY BUSINESS CARD
CREATING THE FUNKY BUSINESS CARD This is what the final product should look like. 1. Open Illustrator 2. Create a new document (file new) Name your document. Change the units to inches. Change the document
A Study of Angles & Curves
A Study of Angles & Curves Method 1: Cutting Quilt Shapes/Using the Shapes Tools Open BERNINA CutWork Software. Make sure that Create New is selected. Click Next. Place a dot in front of New Graphic. Select
Create a Swirly Lollipop Using the Spiral Tool Philip Christie on Jun 13th 2012 with 12 Comments
Advertise Here Create a Swirly Lollipop Using the Spiral Tool Philip Christie on Jun 13th 2012 with 12 Comments Tutorial Details Program: Adobe Illustrator CS5 Difficulty: Beginner Es timated Completion
SOLIDWORKS: Lesson III Patterns & Mirrors. UCF Engineering
SOLIDWORKS: Lesson III Patterns & Mirrors UCF Engineering Solidworks Review Last lesson we discussed several more features that can be added to models in order to increase their complexity. We are now
Decorating the Christmas Tree with Generations Version 1.4 By Bernadette Griffith, Educational Director, Generations Software
Decorating the Christmas Tree with Generations Version 1.4 By Bernadette Griffith, Educational Director, Generations Software The holiday season always brings out the home decorator in us all. Creating
XPEL DAP SUPPORT. DAP Tool List & Overview DESCRIPTION ICON/TOOL (SHORTCUT)
Pointer (S) Left-click on individual entities to add them to the current selection (selected entities will turn red). If the entity selected is a member of a group, the entire group will be added to the
GIMP WEB 2.0 ICONS. GIMP is all about IT (Images and Text) OPEN GIMP
GIMP WEB 2.0 ICONS Web 2.0 Banners: Download E-Book WEB 2.0 ICONS: DOWNLOAD E-BOOK OPEN GIMP GIMP is all about IT (Images and Text) Step 1: To begin a new GIMP project, from the Menu Bar, select File New.
Creating Labels using Label Designer
Creating and setting up a Single Spine Label Template. Creating Labels using Label Designer 1. Click on the Label Designer wizard found under Common Tasks in the Tech Toolbar. A listing of saved templates
Inventor 201. Work Planes, Features & Constraints: Advanced part features and constraints
Work Planes, Features & Constraints: 1. Select the Work Plane feature tool, move the cursor to the rim of the base so that inside and outside edges are highlighted and click once on the bottom rim of the
DTP with MS Publisher
DTP with MS Publisher ICT Curriculum Team 2004 Getting Going Basics desktop publishing a system for producing printed materials that consists of a PERSONAL COMPUTER or COMPUTER workstation, a high-resolution
Chapter 5. Inserting Objects. Highlights
Chapter 5 Inserting Objects Highlights 5. Inserting AutoShapes, WordArts and ClipArts 5. Changing Object Position, Size and Colour 5. Drawing Lines 5.4 Inserting Pictures and Text Boxes 5.5 Inserting Movies
Education and Training CUFMEM14A. Exercise 2. Create, Manipulate and Incorporate 2D Graphics
Education and Training CUFMEM14A Exercise 2 Create, Manipulate and Incorporate 2D Graphics Menu Exercise 2 Exercise 2a: Scarecrow Exercise - Painting and Drawing Tools... 3 Exercise 2b: Scarecrow Exercise
A QUICK TOUR OF ADOBE ILLUSTRATOR CC (2018 RELEASE)
A QUICK TOUR OF ADOBE ILLUSTRATOR CC (2018 RELEASE) Lesson overview In this interactive demonstration of Adobe Illustrator CC (2018 release), you ll get an overview of the main features of the application.
Creative Sewing Machines Workbook based on BERNINA Embroidery Software V8
V8 Lesson 49 Using an Object for a Carving Stamp Edited for V8.1 update. We will start by using Corel to find and save an image. On your desktop there should be 4 Corel icons. I have grouped mine together
V-BOX Cloud Configuration
V-BOX Cloud Configuration Website: http://www.we-con.com.cn/en Technical Support: support@we-con.com.cn Skype: fcwkkj Phone: 86-591-87868869 QQ: 1043098682 Technical forum: http://wecon.freeforums.net/
Delta Dart. Socket. (L) on the Sketch toolbar. Fig. 1. (S) on the Sketch toolbar. on the Sketch toolbar. on the Standard Views toolbar.
Chapter 6 Delta Dart Socket A. Sketch. Step 1. Click File Menu > New, click Part Metric and OK. Step 2. Click Front Plane in the Feature Manager and click Sketch from the Content toolbar, Fig. 1. Step
Creating T-Spline Forms
1 / 28 Goals 1. Create a T-Spline Primitive Form 2. Create a T-Spline Revolve Form 3. Create a T-Spline Sweep Form 4. Create a T-Spline Loft Form 2 / 28 Instructions Step 1: Go to the Sculpt workspace
Working with Graphics and Text
Chapter 2 Working with Graphics and Text Learning Objectives After completing this chapter, you will be able to: Create vector graphics using drawing tools Modify the shape and size of the selected objects
PHOTOSHOP TUTORIAL GUARDIANS OF THE GALAXY POSTER
PHOTOSHOP TUTORIAL GUARDIANS OF THE GALAXY POSTER LEVEL - INTERMEDIATE By Mister LAI PRODUCTION PHASE 1 CREATING THE BACKGROUND ELEMENTS Setup of Photoshop Document 1. To setup new file click on File >
Battery Holder. Chapter 9. Boat. A. Front Extrude. Step 1. Click File Menu > New, click Part and OK. SolidWorks 10 BATTERY HOLDER AA BOAT Page 9-1
Chapter 9 Boat Battery Holder A. Front Extrude. Step 1. Click File Menu > New, click Part and OK. AA Step 2. Click Front (plane) in the Feature Manager and click Sketch from the Content toolbar, Fig. 1.
Transformations in the Plane - Activity 1 Reflections in axes and an oblique line.
Name: Class: p 5 Maths Helper Plus Resource Set. Copyright 00 Bruce A. Vaughan, Teachers Choice Software Transformations in the Plane - Activity Reflections in axes and an oblique line. ) On the diagram
Electrical Cableway Routing
Electrical Cableway Routing Preface Using This Guide What's New? Getting Started Entering the Workbench Placing a Hanger Routing a Loft Through Hangers Placing a Conduit on a Run Saving Documents Updating
LinkMotion and CorelDraw 9, 10, 11, 12, X3, X4, X5, X6, X7 and X8:
LinkMotion and CorelDraw 9, 10, 11, 12, X3, X4, X5, X6, X7 and X8: After you install LinkMotion software and set up all settings launch CorelDraw software. Important notes: Solustan s LinkMotion driver
Virtual MODELA USER'S MANUAL
Virtual MODELA USER'S MANUAL Virtual MODELA is a program that simulates the movement of the tool on the screen. Contents Contents Part 1 Introduction 1-1 System Requirements... 4 1-2 Overview of Virtual
Picket Patterns. Overview
Ornamental Pro 2010 Rail Section and Picket Pattern Drawing Manual Table of Contents Picket Patterns... 1 Overview... 1 Creating a Picket Pattern... 2 Example 1... 2 Vertical Bar Behavior... 2 Example
1st Point. 2nd Point. hold shift & drag along Y. Splines
Splines STEP 1: open 3DS Max _ from the Command Panel under the Create tab click on Shapes (note: shapes are really Splines) _ under Object Type click on Ellipse STEP 2: Expand the Keyboard Entry tab type
wiemarc 5.2 Manual Labeling Software wiemarc 5.2
wiemarc 5.2 Manual Labeling Software wiemarc 5.2 Page 1 of 67 Release: February 16, 2016 Manual labeling software 5.2 Table of contents 1. System requirements 2. Software installation 3. Output devices
Tools of Design Select Mode vs. Text Mode Select Mode allows you to alter the position and size of both text and clipart Text Mode allows you change text size, font and characters but you CANNOT
Using Blending Modes for Simple Color Correction
Using Blending Modes for Simple Color Correction In a previous lesson, you were introduced to blending modes using the Brush Tool. Blending modes are also a powerful feature of the Layers Panel and can
Lesson 1 Parametric Modeling Fundamentals
1-1 Lesson 1 Parametric Modeling Fundamentals Create Simple Parametric Models. Understand the Basic Parametric Modeling Process. Create and Profile Rough Sketches. Understand the "Shape before size" approach.
CO 2 Shell Car. Body. in the Feature Manager and click Sketch from the context toolbar, Fig. 1. on the Standard Views toolbar.
CO 2 Shell Car Chapter 2 Body A. Save as "BODY". Step 1. If necessary, open your BLANK file. Step 2. Click File Menu > Save As. Step 3. Key-in BODY for the filename and press ENTER. B. FRONT Wheel Shell.
2D Design. Window. 3D Window. Toolpat h Operati ons. Navigation Homepage. Layer Managemen t. Component Manager. Modeling Tools
Navigation Homepage Click on the region of the interface you are interested in to navigate to the relevant section of this manual. At the foot of each page is a Navigation Homepage link, click on this
Exercise Guide. Published: August MecSoft Corpotation
VisualCAD Exercise Guide Published: August 2018 MecSoft Corpotation Copyright 1998-2018 VisualCAD 2018 Exercise Guide by Mecsoft Corporation User Notes: Contents 2 Table of Contents About this Guide 4
Getting Started. The main tasks described in this section are the following:
Getting Started Getting Started Before getting into the detailed instructions for using Interactive Drafting workbench, the following tutorial aims at giving you a feel of what you can do with the product.
Welcome to MicroStation
Welcome to MicroStation Module Overview This module will help a new user become familiar with the tools and features found in the MicroStation design environment. Module Prerequisites Fundamental knowledge
Motic Images Plus 3.0 ML Software. Windows OS User Manual
Motic Images Plus 3.0 ML Software Windows OS User Manual Motic Images Plus 3.0 ML Software Windows OS User Manual CONTENTS (Linked) Introduction 05 Menus and tools 05 File 06 New 06 Open 07 Save 07 Save
12 APPLYING EFFECTS. Lesson overview
12 APPLYING EFFECTS Lesson overview In this lesson, you ll learn how to do the following: Use various effects, such as Pathfinder, Scribble, and Drop Shadow. Use Warp effects to distort type. Create three-dimensional
How to Create Greeting Cards using LibreOffice Draw
by Len Nasman, Bristol Village Ohio Computer Club If you want to create your own greeting cards, but you do not want to spend a lot of money on special software, you are in luck. It turns out that with
Introduction To Inkscape Creating Custom Graphics For Websites, Displays & Lessons
Introduction To Inkscape Creating Custom Graphics For Websites, Displays & Lessons The Inkscape Program Inkscape is a free, but very powerful vector graphics program. Available for all computer formats
WIRE BASICS ESTIMATED TIME REQUIRED. This tutorial will teach you the basics of sketching wires and using them as contours for solid objects.
WIRE BASICS This tutorial will teach you the basics of sketching wires and using them as contours for solid objects. ESTIMATED TIME REQUIRED 30 Minutes LEARNING GOALS In this tutorial you will learn how
Lesson 03: We will add water and will set the placing conditions for the material. WorldBuilder 3.5. for. About Digital Element Tutorials:
Lesson 03: We will add water and will set the placing conditions for the material for WorldBuilder 3.5 About Digital Element Tutorials: This tutorial is available both in.pdf format and in Qarbon format,
Chapter 5 Managing Graphic Objects
Impress Guide Chapter 5 Managing Graphic Objects Moving, rotating, distorting, and positioning objects; animations; Fontwork This PDF is designed to be read onscreen, two pages at a time. If you want to
Summer STEM Academy. VCarve Name Sign Instructions
Summer STEM Academy VCarve Name Sign Instructions Follow these instructions to draw your personalized sign on the CNC router in the Woodshop / Manufacturing shop. 1. Log on to your computer and double
Autodesk Inventor Tips & Tricks Placing Features On
1 Autodesk Inventor Tips & Tricks Placing Features On Cylindrical Shapes The adoption of parametric, feature based solid modeling will present many challenges to the new user as they are confronted for
Skateboard. Hanger. in the Feature Manager and click Sketch. (S) on the Sketch. Line
Chapter 3 Skateboard Hanger A. Sketch 1. Step 1. Click File Menu > New, click Part Metric and OK. Step 2. Click Right Plane from the Content toolbar, Fig. 1. in the Feature Manager and click Sketch Step
A Comprehensive Introduction to SolidWorks 2011
A Comprehensive Introduction to SolidWorks 2011 Godfrey Onwubolu, Ph.D. SDC PUBLICATIONS www.sdcpublications.com Schroff Development Corporation Chapter 2 Geometric Construction Tools Objectives: When
Skateboard. Hanger. in the Feature Manager and click Sketch on the Context toolbar, Fig. 1. Fig. 2
Chapter 3 Skateboard Hanger A. Sketch1 Lines. Step 1. Click File Menu > New, click Part Metric and OK. Step 2. Click Right Plane in the Feature Manager and click Sketch on the Context toolbar, Fig. 1.
Lesson 14 Blends. For Resources go to > click on the Creo Parametric 2.0 Book cover
Lesson 14 Blends Figure 14.1 Cap OBJECTIVES Create a Parallel Blend feature Use the Shell Tool Create a Hole Pattern REFERENCES AND RESOURCES For Resources go to www.cad-resources.com > click on the Creo
Microsoft Visio Working with Shapes
Working with Visio Shapes Shape is the general term for the objects you will find on a stencil and objects created using the drawing tools. These include geometric shapes such as rectangles, triangles
Introduction to SolidWorks Basics Materials Tech. Wood
Introduction to SolidWorks Basics Materials Tech. Wood Table of Contents Table of Contents... 1 Book End... 2 Introduction... 2 Learning Intentions... 2 Modelling the Base... 3 Modelling the Front... 10
SPRINGBOARD UNIT 5 GEOMETRY
SPRINGBOARD UNIT 5 GEOMETRY 5.1 Area and Perimeter Perimeter the distance around an object. To find perimeter, add all sides. Area the amount of space inside a 2 dimensional object. Measurements for area
KEYCREATOR 3D Direct Modeling Software
KeyCreator Lesson KC5107 Graft The Graft Function is a powerful partner to the Prune Function that we used earlier. You will typically use the Graft Function immediately after performing a pruning operation
Delta Dart. Propeller. in the Feature Manager and click Sketch from the Content toolbar, Fig. 1. on the Sketch toolbar.
Chapter 8 Delta Dart Propeller A. Base for Blade. Step 1. Click File Menu > New, click Part Metric and OK. Step 2. Click Top Plane in the Feature Manager and click Sketch from the Content toolbar, Fig.
Fig. A. Fig. B. Fig. 1. Fig. 2. Fig. 3 Fig. 4
Create A Spinning Logo Tutorial. Bob Taylor 2009 To do this you will need two programs from Xara: Xara Xtreme (or Xtreme Pro) and Xara 3D They are available from: http://www.xara.com. Xtreme is available
Tutorial 3: Using the Waveform Viewer Introduces the basics of using the waveform viewer. Read Tutorial SIMPLIS Tutorials SIMPLIS provide a range of t
Tutorials Introductory Tutorials These tutorials are designed to give new users a basic understanding of how to use SIMetrix and SIMetrix/SIMPLIS. Tutorial 1: Getting Started Guides you through getting
SIMPLE TEXT LAYOUT FOR COREL DRAW. When you start Corel Draw, you will see the following welcome screen.
SIMPLE TEXT LAYOUT FOR COREL DRAW When you start Corel Draw, you will see the following welcome screen. A. Start a new job by left clicking New Graphic. B. Place your mouse cursor over the page width box.