MONOPRICE. MP USB Powered 15.6" IPS FHD Graphic Pen Display Tablet. User's Manual P/N 21826

Transcription

1 MONOPRICE MP USB Powered 15.6" IPS FHD Graphic Pen Display Tablet P/N User's Manual

2 CONTENTS SAFETY WARNINGS AND GUIDELINES... 4 INTRODUCTION... 5 FEATURES... 6 CUSTOMER SERVICE... 6 PACKAGE CONTENTS... 6 SYSTEM REQUIREMENTS... 7 PRODUCT OVERVIEW... 7 Front Panel... 7 Rear and Side Panels... 8 Pen... 8 Integrated Cable... 9 Controls... 9 ASSEMBLING THE AC POWER ADAPTER ATTACHING THE STAND CHARGING THE PEN REPLACING THE PEN NIB SOFTWARE INSTALLATION HARDWARE CONNECTION SOFTWARE OPERATION Press Keys Tab Stylus Pen Tab Work Area Tab About Tab OSD MENU SYSTEM

3 OSD Menu Operation Picture Menu Display Menu Color Menu Advance Menu Input Menu Audio Menu Other Menu TECHNICAL SUPPORT SPECIFICATIONS REGULATORY COMPLIANCE Notice for FCC Notice for Industry Canada

4 SAFETY WARNINGS AND GUIDELINES Please read this entire manual before using this device, paying extra attention to these safety warnings and guidelines. Please keep this manual in a safe place for future reference. This device is intended for indoor use only. Do not expose this device to water or moisture of any kind. Do not place drinks or other containers with moisture on or near the device. If moisture does get in or on the device, immediately unplug it from the power outlet and allow it to fully dry before reapplying power. Do not touch the device, the power cord, or any other connected cables with wet hands. Do not place the monitor on an unstable surface where it could fall and cause either personal injury or damage to the monitor and/or other equipment. Do not expose this device to excessively high temperatures. Do not place it in, on, or near heat sources, such as a fireplace, stove, radiator, etc. Do not leave it in direct sunlight. This device ventilates excessive heat through the slots and openings in the case. Do not block or cover these openings. Ensure that the device is in an open area where it can get sufficient airflow to keep from overheating. Do not place or install this device in an area where it can be exposed to excessive amounts of dust, humidity, oil, smoke, or combustible vapors. Prior to operation, check the unit and power cord for physical damage. Do not use if physical damage has occurred. Before plugging the unit into a power outlet, ensure that the outlet provides the same type and level of power required by the device. Take care to prevent damage to the power cord. Do not allow it to become crimped, pinched, walked on, or become tangled with other cords. Ensure that the power cord does not present a tripping hazard. Never unplug the unit by pulling on the power cord. Always grasp the connector head or adapter body. 4

5 Ensure that power is turned off and disconnected before making any electrical connections. Keep the display and pen away from magnetic fields. Clean using a soft, dry cloth only. Do not use chemical cleaners, solvents, or detergents. For stubborn deposits, moisten the cloth with warm water. This device has no user serviceable parts. Do not attempt to open, service, or modify this device. This device contains small parts that could pose a choking hazard to small children. Keep this device and its spare parts out of reach of small children. The pen for this device contains a Lithium-polymer battery. Dispose of the pen only in accordance with local, state, or federal regulations for electronic waste. Charge the battery in the pen before first use and at least once every three months. When storing the pen, ensure that there is no pressure on the tip. Pressure on the tip will cause the pen to stay powered on, which will drain the battery. INTRODUCTION Thank you for purchasing this Graphic Pen Display Tablet! This display features a touch screen with 5080 lines-per-inch resolution and 2048 pressure levels. It allows you to draw directly on your graphic when using graphic design programs, thereby ensuring greater drawing accuracy than using a mouse or conventional graphic tablet. It features an HDMI video interface, with a maximum 1920x1080p resolution, and connects to a computer using the USB interface. The pen uses a rechargeable battery, which will give up to 350 hours of operation on a full charge, and weighs only 0.58 ounces (16.5g). 5

6 FEATURES HDMI video input with 1920x1080p maximum resolution 5080 lines per inch (LPI) drawing resolution and 2048 pressure levels 178 horizontal and vertical viewing angles with contrast ratio greater than 10:1 Rechargeable pen with up to 350 hours operating time Compatible with Windows 7 or later and Mac OS X or later CUSTOMER SERVICE The Monoprice Customer Service department is dedicated to ensuring that your ordering, purchasing, and delivery experience is second to none. If you have any problem with your order, please give us an opportunity to make it right. You can contact a Monoprice Customer Service representative through the Live Chat link on our website during normal business hours (Mon-Fri: 5am-7pm PT, Sat-Sun: 9am- 6pm PT) or via at support@monoprice.com PACKAGE CONTENTS Please take an inventory of the package contents to ensure you have all the items listed below. If anything is missing or damaged, please contact Monoprice Customer Service for a replacement. 1x 15" graphic pen display tablet with installed tilt stand 1x Rechargeable pen 1x Integrated HDMI, USB, and power cable 1x AC power adapter 1x NEMA 1-10 plug for power adapter 1x Pen holder with 8 spare pen nibs 1x Pen charging cable 1x Drivers CD 1x User's manual 6

7 SYSTEM REQUIREMENTS Computer running Windows 7 or later or Mac OS X or later Available USB port HDMI video output Optical disc drive or internet connection for driver installation PRODUCT OVERVIEW Front Panel 7

8 Rear and Side Panels Pen 8

9 Integrated Cable Controls AUTO: When the OSD menu is not displayed, press the AUTO button to automatically adjust the image. When the OSD menu is displayed, press the AUTO button to back out one menu level or to close the OSD menu if at the top level. If editing an entry, press the AUTO button to cancel any changes made. -: When the OSD menu is displayed, press the - button to move the highlight to the left or down. When an option is being edited in the OSD menu system, press the - button to decrease the value. 9

10 +: When the OSD menu is displayed, press the + button to move the highlight to the right or up. When an option is being edited in the OSD menu system, press the + button to increase the value. MENU: When the OSD menu is not displayed, press the MENU button to display the OSD menu. When the OSD menu is displayed, press the MENU button to select the highlighted submenu or to select an entry for editing. While editing an OSD menu entry, press the MENU button to save any changes made. POWER: Press the POWER button to the display on or off. ASSEMBLING THE AC POWER ADAPTER The AC power adapter for this Pen Display uses a detachable plug, allowing it to be customized for non-us markets. Before using the adapter, you must assemble it by sliding the NEMA 1-15 plug onto the top of the adapter, as shown in the diagram below. If you ever need to remove the plug, push the locking switch back, then slide the plug off the adapter. 10

11 USING THE STAND The included tilting stand comes installed out of the box. To use the stand, pull up on the indicated switch to unlock the tilt, allowing it to be adjusted to the desired angle between If you want to use a desk or wall mount, remove the installed stand by removing the four screws that fix it in place, then use the screws to attach the monitor to the mount. CHARGING THE PEN The included pen stylus features a built-in rechargeable battery that gives up to 350 hours of continuous operation. The pen should be fully charged before first use and should be charged at least once every three months to keep the battery fresh and capable of holding a full charge. To charge the pen, plug the DC barrel connector on the included charging cable into the top of the pen, then plug the USB connector into a USB power source, such as a USB port on your computer or a USB wall charger. The LED indicator on the pen will glow red while charging is in progress and will extinguish when charging is complete. When the LED indicator glows orange dusring use, the battery is low and should be recharged immediately. 11

12 REPLACING THE PEN NIB With repeated use the pen nib (tip) will wear out. When it does, you can easily replace it with one of the included replacement nibs. To do so, grab the nib with the nib removal clip and pull it out of the pen. Next, open the pen holder and remove one of the replacement nibs. Insert the new nib into the end of the pen and press the pen down on a flat surface to fully seat the new nib in the pen. SOFTWARE INSTALLATION Before connecting the display to your computer, you should install the software driver package. You can install the driver from the included CD or go to and download the latest version of the driver for installation. After launching the installer, follow the on screen instructions to complete the installation. HARDWARE CONNECTION Perform the following steps to connect the pen display to your computer. 1. Plug the USB-C and Mini HDMI connectors on the included integrated cable into the USB-C and Mini HDMI connectors on the right side of the display. 2. Plug the USB-A and HDMI connectors on the included integrated cable into an available USB-A port and HDMI video port on your computer. 3. Plug the included AC power adapter into the power connector on the included integrated cable, then plug it into a nearby AC power outlet. 12

13 SOFTWARE OPERATION Press Keys Tab The pen display features 10 hotkeys, which can be assigned to perform any single keystroke, mouse action, or combination of keystrokes. To set these keys, open the installed software and click on the Press Keys tab. Next, hover the mouse over the key you want to configure, then click on the key label to open the key edit screen. Click the OK button to save your changes or click the Cancel button to abort any changes. 13

14 Stylus Pen Tab The Stylus Pen tab allows you to assign any single keystroke, mouse action, or combination of keystrokes to each of the two buttons. To do so, click the button associated with the button you want to change to open the key assignment dialog. Additionally, you can set and test the pressure sensitivity of the pen tip. Note that the pen tip will always perform a mouse left-click. Finally, you can enable support for Windows Ink by checking the box in the lower left corner. 14

15 Work Area Tab When using the pen display as the only monitor on your computer system, the working area (the part of the display that is pen responsive) is the entire display by default. However, when using the pen display in conjunction with other monitors on your system, you need to determine the location of the pen display in relation to your main display and determine whether it will be a mirror of the main display or whether it will extend the desktop. Refer to your operating system manual for instructions on how to do this. 15

16 Once the monitor is part of your multi-monitor system, you need to set the active pen responsive area to all or a portion of the pen display. You can set it to the full area by clicking the Full Area button. Alternatively, you can set it to the screen ratio by clicking the Screen Ratio button. Finally, you can set the active area by dragging the sides of the green box. You can also rotate the display for left handed operation or portrait orientation by clicking one of the radio buttons in the Rotate section. 16

17 To ensure accurate drawing, you should periodically calibrate the monitor and pen responsive area. To do so, click the Monitor Calibration button. You will be presented with a series of crosshairs around a red dot. Click the red dots in order to calibrate the monitor and pen responsive area. While calibration is in progress, you can reset the calibration to the factory defaults by clicking the Restore default button. Alternatively, you can cancel calibration by clicking the Cancel Calibration button. 17

18 About Tab The About tab allows you to save or load settings or to reset all settings to their factory default values. Click the Import Config button to load a previously saved setting. Click the Export Config button save the current settings to a file on your computer. Click the Default Config button to reset all values to their factory default values. OSD MENU SYSTEM This monitor features a built-in On-Screen Display (OSD) menu system, which allows you to change the monitor's settings. OSD Menu Operation If the OSD menu is not displayed, press the MENU button to display the OSD menu. If the OSD menu is displayed, press the MENU button to select and display the highlighted submenu or to select the highlighted entry for editing. If editing an entry in the OSD menu, press the MENU button to save the displayed value and exit editing that entry. If the OSD menu is displayed, press the AUTO button to back out of a submenu. 18

19 If at the top level of the OSD menu, press the AUTO button to exit the OSD menu. If editing an entry in the OSD menu, press the AUTO button to cancel any changes made and exit editing that entry. If the OSD menu is displayed, press the - button to move the highlight up or to the left. If the OSD menu is displayed, press the + button to move the highlight down or to the right. If editing an entry in the OSD menu, press the - button to decrease the displayed value. If editing an entry in the OSD menu, press the + button to increase the displayed value. Picture Menu Backlight: Adjusts the amount of backlighting used on the display. The adjustment range is Brightness: Adjusts the image brightness of the display. The adjustment range is Contrast: Adjusts the image contrast of the display. The adjustment range is Sharpness: Adjusts the sharpness of the image on the display. The adjustment range is Display Menu Disp Rotate: Optionally rotates the display for left-handed use. The available options are 0 (not rotated) and 180 (rotated). Note that this does not rotate the OSD menu. The OSD menu can be rotated using the Rotate option in the Other menu. 19

20 Color Menu Panel Uniformity: When enabled, changes to the backlighting are kept local to the individual panel region(s) rather than apply to the entire panel. The available options are On and Off. Gamma: Determines the shape of the brightness curve. The available options are Off, 1.8, 2.0, 2.2, and 2.4. Temperature: Allows you to set the color temperature of the display to one of the standard presets or to manually configure the individual color mix. The available options are 9300, 7500, 6500, 5800, srgb, and User. When User is selected, you will be presented with a submenu, with R, G, and B options, with each having a range of Color Effect: Allows you to adjust the image appearance to one of the available presets or to customize the appearance manually. The available options are Standard, Game, Movie, Photo, Vivid, and User. When User is selected, you will be presented with a submenu with R, Y, G, C, B, and M entries. Each entry presents another submenu that allows you to set the individual Hue and Saturation for each color, with the range for each. Demo: Allows you to enable one of the available demonstration modes. The available options are Off, Type1, Type2, Type3, Type4, and Type5. Color Format: The display should automatically detect whether your video card is using an RGB or YUV color space. However, if the colors look wrong, then manually change the color space using this menu option. The available options are RGB and YUV. PCM: PCM mode is an exclusive calibration setting for use with third party calibration hardware and software. The available options are srgb, Adobe RGB, User, and Native. Hue: Allows you to set the overall Hue of the image on screen. The adjustment range is Saturation: Allows you to set the overall Saturation of the image on screen. The adjustment range is

21 Advance Menu Aspect Ratio: Allows you to set the aspect ratio of the image on screen. The available options are Full, 16:9, 4:3, 5:4, and 1:1. Over Scan: Improves the response time. The available options are On and Off. Over Drive: Improves the response time. The available options are On and Off. When enabled, the OD Gain is adjustable from DCR: Not used. DDCCI: This function determines whether the DDC/CI commands are supported or not. Unless using a legacy operating system or one that does not support DDC/CI, this should remain On. The available options are On and Off. Ultra Vivid: This is another form of edge enhancement to eliminate ghosting around text on the screen. The available options are Off, L (Low), M (Medium), and H (High). Input Menu Because this monitor features only a single HDMI input, this menu is not used. Audio Menu This monitor does not support audio, therefore this menu is not used. Other Menu Reset: Resets the OSD menu to the factory default values. Menu Time: Sets the amount of time that the OSD menu will remain on screen without any buttons being pressed. The adjustment range is 0 and 5-60 seconds. OSD H Position: Sets the horizontal position of the OSD menu on screen. The adjustment range is OSD V Position: Sets the vertical position of the OSD menu on screen. The adjustment range is

22 Language: Allows you to set the language used in the OSD menu. The available options are E (English) and C (Chinese). Transparency: Sets the transparency or opacity of the OSD menu. The adjustment range is 0-256, with 0 having no transparency and 256 having maximum transparency. Rotate: Allows you to rotate the orientation of the OSD menu. The available options are 0 (normal), 90, 270, and 180 (inverted). Information Menu The information menu consists of a single screen, which shows the video type, the screen resolution and refresh rate, the horizontal and pixel clock frequencies, and the HDCP status. Factory Menu This menu is not used. TECHNICAL SUPPORT Monoprice is pleased to provide free, live, online technical support to assist you with any questions you may have about installation, setup, troubleshooting, or product recommendations. If you ever need assistance with your new product, please come online to talk to one of our friendly and knowledgeable Tech Support Associates. Technical support is available through the online chat button on our website during regular business hours, 7 days a week. You can also get assistance through by sending a message to tech@monoprice.com 22

23 SPECIFICATIONS Model Panel Size 15.6" Maximum Resolution Video Inputs LCD Type Active Area 1920 x 1080p 1x HDMI TFT LCD IPS x mm Contrast Ratio 1000:1 Brightness 250 cd/m 2 Response Time 25ms Viewing Angles 178 horizontal and vertical (CR > 10:1) Touch Type Touch Resolution Pressure Levels Sensing Height Report Rate Pen Type Electromagnetic resonance 5080 lines-per-inch (LPI) 2048 levels 10mm 233rps Cordless Active Maximum Pen Tilt Angle ±45 Pen Battery Capacity Pen Charge Time Pen Operating Time Pen Auto Sleep Time Pen Dimensions Pen Weight 80mAh about 1.3 hours up to 350 hours 15 minutes 0.5" x 7.0" (ø14 x 178 mm) 0.58 oz. (16.5g) 23

24 Input Power AC Adapter Input Power Maximum Power Consumption 12 VDC, 1A 100~240 VAC, 50/60 Hz 12 watts Adjustable Stand Angle 20 ~ 80 Dimensions Weight Supported Operating Systems 17.8" x 9.9" x 0.8" (452 x 252 x 20 mm) 3.5 lbs. (1.58 kg) Microsoft Windows 7 or later Apple Mac OS X or later REGULATORY COMPLIANCE Notice for FCC Modifying the equipment without Monoprice s authorization may result in the equipment no longer complying with FCC requirements for Class B digital devices. In that event, your right to use the equipment may be limited by FCC regulations, and you may be required to correct any interference to radio or television communications at your own expense. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: 24

25 Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/tv technician for help. Notice for Industry Canada This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. HDMI, the HDMI Logo, and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries. Microsoft and Windows are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. Apple, Mac, and OS X are trademarks of Apple Inc., registered in the U.S. and other countries. 25