ZyXEL ES-3124 V3.80(TP.3)C0 Release Note/Manual Supplement

Size: px

Start display at page:

Download "ZyXEL ES-3124 V3.80(TP.3)C0 Release Note/Manual Supplement"

Willis Walton
6 years ago
Views:

1 ZyXEL ES-3124 V3.80(TP.3)C0 Release Note/Manual Supplement Date: June 17, 2011 This document describes the features in the ES-3124 product for its 3.80(TP.3)C0 release. Support Platforms: ZyXEL ES-3124 V3.80(TP.3)C0 supports models: ZyXEL ES-3124 Version: ZyNOS Version: V3.80(TP.3) 6/17/ :18:33 BootBase Version: V1.0 07/06/ :24:45 Enhanced Features s MSTP 2. SNMPv3 3. enlarge syslog buffer ah OAM 5. Multilevel CLI 6. SNMP trap group 7. configurable multicast VLAN 8. independent IGMP snooping and MVR setting 9. enlarge concurrent telnet session 10. IP source guard(static binding, DHCP snooping, ARP inspection) 11. Two rate three color marking 12. IP subnet VLAN 13. RADIUS MAC login 14. RADIUS accounting 15. TACACS+ authentication 16. TACACS+ accounting 17. IGMPv3 snooping 18. Loop guard 19. Daylight saving 20. Bootbase changes to v1.0 for manufacturer only 21. There is no effect upon present products of changed Bootbase Default Bootbase Setting: ZyNOS Version V3.80(TP.3) 6/17/ :18:33 Bootbase Version V1.0 07/06/ :24:45 Vendor Name ZyXEL Communications Corp. Product Model ES-3124 ZyNOS Code Model ES-3000 HTP Code Model Unknown ZyNOS ROM address System Type 10 First MAC Address 0019CB Last MAC Address 0019CB000002

2 MAC Address Quantity 02 Default Country Code FF Boot Module Debug Flag 01 RomFile Version 8A RomFile Checksum a506 ZyNOS Checksum a3a7 SNMP MIB level & OID Main Feature Bits C0 Other Feature Bits C Features: 1. MAC address learning 2. Support IEEE 802.1D transparent bridge 3. Support IEEE 802.1Q tagged VLAN 4. Support Port-based VLAN 5. Support IEEE 802.1X 6. Support IEEE 802.1W 7. Support IEEE 802.3AD 8. Support GVRP 9. IGMP snooping 10. Support IEEE 802.1p 11. Automatic age out 12. Specific MAC addresses forwarding per port 13. MAC Filtering 14. Port Trunking 15. Port Mirroring 16. Bandwidth Control 17. Broadcast Storm Control 18. Support Strict Priority and WRR queuing method 19. Static IP management or dynamic IP(DHCP client) 20. Multiple IP address management 21. Firmware upgrade and configuration backup/restore. 22. Remote manageable. 23. Cluster Management 24. WEB manageable 25. Support RFC-1213 MIB II 26. Support RFC-1493 Bridge MIB 27. Support RFC-1643 Ethernet MIB 28. Support RFC-1757 Four group of RMON 29. Support RFC-2674 VLAN MIB 30. NEW CLI supported 31. System configuration backup / restore in text-mode 32. Multiple login supported 33. Radius management authentication 34. SSH/SSL support 35. Syslog 36. Protocol based VLAN support 37. DiffServ feature (DSCP 802.1p priority mapping) 38. Multiple RSTP 39. RADIUS enhancement(for 802.1X enhancenment and multiple radius servers) 40. Administration user management 41. IGMP enhancement 42. Web enhancement (Select all, Clone) 43. Reserve multicast group support

3 Bug Fix: 1. [MAC]After change the DUT s MAC address with specific number c86c and reboot with default ROM, some abnormal message will be shown in console. Known Issues: 1. Management port test fail in 100M long cable. 2. Management port has compatible issue with Cnet Pro 2000 network interface card. 3. The packets which destination address is marked in the filter setting will always send to port Symbol and dribble error packets will count into FCS error counter. 5. Filtering: In some special cases, setting one MAC with discard-source will cause device filter all packets with this MAC, ether source MAC or destination MAC. 6. Do not suggest cooperate LACP with RSTP more than ten ports. 7. Do not support tagged frame forwarding in the Port-Based VLAN. 8. If the contact between RJ45 and wire cable or the wire cable is unstable, the cable diagnostics maybe fail. 9. Modify the high threshold of system FAN RPM to FW upgrade page will be enhanced further. 11. The system-wide rule entries are shared with CIR rate control and policy rules. So you may fail to load max policy rules while enabling CIR rate control on all ports. 12. Ports configured to run RSTP will not synchronize with peers if the port is in BLOCK mode. 13. Packets MAC with tagged vlan id which is not configured in device will be learned. 14. Port configured in fixed-speed mode (AN is disable) for change may not link up. It could be linked up with operation SOP (link down then link up manually) Limitation of Settings: 1. VLAN 1Q static entry Static MAC forwarding entry MAC filtering entry Cluster member Management IP address Protocol based VLAN entries per port 7 7. The number of dhcp snooping can learn is The subnet based vlan can support up to 48 rules. Firmware Upgrade: The ES-3124 uses FTP to upgrade firmware in run-time through its built-in FTP server. You can use any FTP client (for example, ftp.exe in Windows) to upgrade ES The upgrade procedure is as follows: Upgrade ES-3124 FW: C:\> ftp <ES-3124 IP address> User : admin Password: Logged in ftp> put 380TP3C0.bin ras ftp> bye Where User name : the management user name, admin by default Password : the management password, 1234 by default

4 380TP3C0.bin : the name of firmware file you want to upgrade ras : the internal firmware name in ES-3124 Configuration Upgrade: The ES-3124 uses FTP to upgrade configuration in run-time through its built-in FTP server. You can use any FTP client (for example, ftp.exe in Windows) to upgrade ES The upgrade procedure is as follows: Upgrade ES-3124 configuration: C:\> ftp <ES-3124 IP address> User : admin Password: Logged in ftp> put 380TP3C0.rom rom-0 ftp> bye Where User name : the management user name, admin by default Password : the management password, 1234 by default 380TP3C0.rom : the name of configuration file you want to upgrade rom-0 : the internal configuration name in ES-3124

5 ZyXEL ES-3124 V3.80(TP.2)C0 Release Note/Manual Supplement Date: May 10, 2010 This document describes the features in the ES-3124 product for its 3.80(TP.2)C0 release. Support Platforms: ZyXEL ES-3124 V3.80(TP.2)C0 supports models: ZyXEL ES-3124 Version: ZyNOS Version: V3.80(TP.2) 6/22/ :52:30 BootBase Version: V1.0 07/06/ :24:45 Enhanced Features s MSTP 2. SNMPv3 3. enlarge syslog buffer ah OAM 5. Multilevel CLI 6. SNMP trap group 7. configurable multicast VLAN 8. independent IGMP snooping and MVR setting 9. enlarge concurrent telnet session 10. IP source guard(static binding, DHCP snooping, ARP inspection) 11. Two rate three color marking 12. IP subnet VLAN 13. RADIUS MAC login 14. RADIUS accounting 15. TACACS+ authentication 16. TACACS+ accounting 17. IGMPv3 snooping 18. Loop guard 19. Daylight saving 20. Bootbase changes to v1.0 for manufacturer only 21. There is no effect upon present products of changed Bootbase Default Bootbase Setting: ZyNOS Version V3.80(TP.2) 6/22/ :52:30 Bootbase Version V1.0 07/06/ :24:45 Vendor Name ZyXEL Communications Corp. Product Model ES-3124 ZyNOS Code Model ES-3000 HTP Code Model Unknown ZyNOS ROM address System Type 10 First MAC Address 0019CB Last MAC Address 0019CB MAC Address Quantity 02

6 Default Country Code FF Boot Module Debug Flag 01 RomFile Version 8A RomFile Checksum a506 ZyNOS Checksum fd97 SNMP MIB level & OID Main Feature Bits C0 Other Feature Bits C Features: 1. MAC address learning 2. Support IEEE 802.1D transparent bridge 3. Support IEEE 802.1Q tagged VLAN 4. Support Port-based VLAN 5. Support IEEE 802.1X 6. Support IEEE 802.1W 7. Support IEEE 802.3AD 8. Support GVRP 9. IGMP snooping 10. Support IEEE 802.1p 11. Automatic age out 12. Specific MAC addresses forwarding per port 13. MAC Filtering 14. Port Trunking 15. Port Mirroring 16. Bandwidth Control 17. Broadcast Storm Control 18. Support Strict Priority and WRR queuing method 19. Static IP management or dynamic IP(DHCP client) 20. Multiple IP address management 21. Firmware upgrade and configuration backup/restore. 22. Remote manageable. 23. Cluster Management 24. WEB manageable 25. Support RFC-1213 MIB II 26. Support RFC-1493 Bridge MIB 27. Support RFC-1643 Ethernet MIB 28. Support RFC-1757 Four group of RMON 29. Support RFC-2674 VLAN MIB 30. NEW CLI supported 31. System configuration backup / restore in text-mode 32. Multiple login supported 33. Radius management authentication 34. SSH/SSL support 35. Syslog 36. Protocol based VLAN support 37. DiffServ feature (DSCP 802.1p priority mapping) 38. Multiple RSTP 39. RADIUS enhancement(for 802.1X enhancenment and multiple radius servers) 40. Administration user management 41. IGMP enhancement 42. Web enhancement (Select all, Clone) 43. Reserve multicast group support

7 Bug Fix: 1. Fix memory leak issue that the console will show cli_proc: cli_init out of memory. 2. Fix MVR broken configuration that after running MVR for a period, the IGMP-Querier- Mode will turn to <NULL>. 3. Fix that static MAC forwarding may be cleared from mac-address table while ARP inspection enabled. 4. Fix that ARP inspection will block all traffic if too many ARP packets come into trust ports. 5. Fix that cable-diagnostics for FE port isn't stable. 6. Fix looping in fiber port when restore configuration. 7. Fix that port with bandwidth control enabled conflicts with trunking if bandwidth control is global active. 8. Fix arp inspection issue for Vista gratuitous ARP. 9. Fix that web access fail for IE7+Silverlight. 10. Fix that when we try to get MAC-table from specific VLAN via snmpwalk, the result is wrong. 11. Fix that while setting up port-security and bcp-transparency at the same time, BPDU would flood out from the port configured bpdu discard. 12. Fix that the related ARP entry will be cleared after mac-flush. 13. Fix a TACACS+ issue on DUT. Use DUT and ClearBox TACACS+ Server for using accounting type Commands, but the server don t display info about command completed. 14. Fix login will fail by adding cisco avpair that we don t support. 15. Fix when use ftp login, DUT may cause crash somewhere. 16. Fix DHCP renew packet cannot be forwarded to trunk port when enabling DHCP snooping. 17. Fix our switch will keep printing infinitely, when use TFTP server backup running configuration. 18. Fix all management will lose after unsuccessful login via SecureCRT SSH2 if the operator changes login account. 19. Fix connect with DUT in SSH protocol without correct name or password, and that will cause memory leak. 20. Fix VLAN-Static VLAN Web GUI bug (because of more than 256 VLAN setting). 21. Fix static MAC forwarding entries cannot be deleted as anticipation. 22. Fix when the DHCP snooping and DHCP relay are enabled in the same time, DHCP relay will relay dhcp request to server that coming from DHCP snooping vlan. 23. Fix vlan1q port-isolation can only be set while vlan-type is 802.1q. 24. Avoiding looping by ignore the dhcp snooping pkt when the port is STP block port. 25. Fix when arp inspection is turn on and there are ARPs with CPU mac, do not add it into black list. 26. Fix multicast group entry is getting less and less,when l2 table hash has collision or l2 table full. 27. Fix enable lacp and no trunk member, vlan will disappear (after reboot or restore configuration). 28. Fix that port security can not work correctly after mac-flush. 29. Fix that DUT will crash on web-interface while delete un-existed policy entry by CLI. 30. Fix system may crash when receiving a crafted IP packet with a null length of data portion. 31. Fix that DUT may hang while doing oam loopback test. 32. Keep hw monitor fan when low temperature (<10 o C). 33. Fix the MSTP can not work when our devices cooperate with HUAWEI device. 34. Fix the authentication will fail when first authentication by tacacs then radius. 35. Fix static route rule can be created with the destination IP address in web, but CLI can t. 36. Fix enabled port intrusion, and do port test can cause port link down. 37. Fix the Port link down but port state of spanning-tree still forwarding or the root bridge have blocking port ( port link up ) when topology change over night. 38. Fix when using SilverCreek to test the multicastportigmpfilteringprofile (OID: ) with incorrect indices, DUT will crash. 39. Fix when user key in, in CLI, the system will be hung. 40. Fix when enable remote management, but not enable any service (telnet, http...), after reboot DUT, DUT will pop error message.

8 41. Fix the DHCP option82 will be cascaded if enable DHCP snooping and option82 on the DUTs that cascaded. Option82 will only be added while DHCP packets come from untrust ports. Known Issues: 1. Management port test fail in 100M long cable. 2. Management port has compatible issue with Cnet Pro 2000 network interface card. 3. The packets which destination address is marked in the filter setting will always send to port Symbol and dribble error packets will count into FCS error counter. 5. Filtering: In some special cases, setting one MAC with discard-source will cause device filter all packets with this MAC, ether source MAC or destination MAC. 6. Do not suggest cooperate LACP with RSTP more than ten ports. 7. Do not support tagged frame forwarding in the Port-Based VLAN. 8. If the contact between RJ45 and wire cable or the wire cable is unstable, the cable diagnostics maybe fail. 9. Modify the high threshold of system FAN RPM to FW upgrade page will be enhanced further. 11. The system-wide rule entries are shared with CIR rate control and policy rules. So you may fail to load max policy rules while enabling CIR rate control on all ports. 12. Ports configured to run RSTP will not synchronize with peers if the port is in BLOCK mode. 13. Packets MAC with tagged vlan id which is not configured in device will be learned. 14. Port configured in fixed-speed mode (AN is disable) for change may not link up. It could be linked up with operation SOP (link down then link up manually) Limitation of Settings: 1. VLAN 1Q static entry Static MAC forwarding entry MAC filtering entry Cluster member Management IP address Protocol based VLAN entries per port 7 7. The number of dhcp snooping can learn is The subnet based vlan can support up to 48 rules. Firmware Upgrade: The ES-3124 uses FTP to upgrade firmware in run-time through its built-in FTP server. You can use any FTP client (for example, ftp.exe in Windows) to upgrade ES The upgrade procedure is as follows: Upgrade ES-3124 FW: C:\> ftp <ES-3124 IP address> User : admin Password: Logged in ftp> put 380TP2C0.bin ras ftp> bye Where User name : the management user name, admin by default Password : the management password, 1234 by default 380TP2C0.bin : the name of firmware file you want to upgrade

9 ras : the internal firmware name in ES-3124 Configuration Upgrade: The ES-3124 uses FTP to upgrade configuration in run-time through its built-in FTP server. You can use any FTP client (for example, ftp.exe in Windows) to upgrade ES The upgrade procedure is as follows: Upgrade ES-3124 configuration: C:\> ftp <ES-3124 IP address> User : admin Password: Logged in ftp> put 380TP2C0.rom rom-0 ftp> bye Where User name : the management user name, admin by default Password : the management password, 1234 by default 380TP2C0.rom : the name of configuration file you want to upgrade rom-0 : the internal configuration name in ES-3124

10 ZyXEL ES-3124 V3.80(TP.1)C0 Release Note/Manual Supplement Date: Mar 07, 2008 This document describes the features in the ES-3124 product for its 3.80(TP.1)C0 release. Support Platforms: ZyXEL ES-3124 V3.80(TP.1)C0 supports models: ZyXEL ES-3124 Version: ZyNOS Version: V3.80(TP.1) 3/7/ :47:12 BootBase Version: V1.0 07/06/ :24:45 Enhanced Features s MSTP 2. SNMPv3 3. enlarge syslog buffer ah OAM 5. Multilevel CLI 6. SNMP trap group 7. configurable multicast VLAN 8. independent IGMP snooping and MVR setting 9. enlarge concurrent telnet session 10. IP source guard(static binding, DHCP snooping, ARP inspection) 11. Two rate three color marking 12. IP subnet VLAN 13. RADIUS MAC login 14. RADIUS accounting 15. TACACS+ authentication 16. TACACS+ accounting 17. IGMPv3 snooping 18. Loop guard 19. Daylight saving 20. Bootbase changes to v1.0 for manufacturer only 21. There is no effect upon present products of changed Bootbase Default Bootbase Setting: ZyNOS Version V3.80(TP.1) 3/7/ :47:12 Bootbase Version V1.0 07/06/ :24:45 Vendor Name ZyXEL Communications Corp. Product Model ES-3124 ZyNOS Code Model ES-3000 HTP Code Model Unknown ZyNOS ROM address System Type 10 MAC Address 0019CB Default Country Code FF Boot Module Debug Flag 01

11 RomFile Version 8A RomFile Checksum a506 ZyNOS Checksum 5f66 SNMP MIB level & OID Main Feature Bits C0 Other Feature Bits C Features: 1. MAC address learning 2. Support IEEE 802.1D transparent bridge 3. Support IEEE 802.1Q tagged VLAN 4. Support Port-based VLAN 5. Support IEEE 802.1X 6. Support IEEE 802.1W 7. Support IEEE 802.3AD 8. Support GVRP 9. IGMP snooping 10. Support IEEE 802.1p 11. Automatic age out 12. Specific MAC addresses forwarding per port 13. MAC Filtering 14. Port Trunking 15. Port Mirroring 16. Bandwidth Control 17. Broadcast Storm Control 18. Support Strict Priority and WRR queuing method 19. Static IP management or dynamic IP(DHCP client) 20. Multiple IP address management 21. Firmware upgrade and configuration backup/restore. 22. Remote manageable. 23. Cluster Management 24. WEB manageable 25. Support RFC-1213 MIB II 26. Support RFC-1493 Bridge MIB 27. Support RFC-1643 Ethernet MIB 28. Support RFC-1757 Four group of RMON 29. Support RFC-2674 VLAN MIB 30. NEW CLI supported 31. System configuration backup / restore in text-mode 32. Multiple login supported 33. Radius management authentication 34. SSH/SSL support 35. Syslog 36. Protocol based VLAN support 37. DiffServ feature (DSCP 802.1p priority mapping) 38. Multiple RSTP 39. RADIUS enhancement(for 802.1X enhancenment and multiple radius servers) 40. Administration user management 41. IGMP enhancement 42. Web enhancement (Select all, Clone) 43. Reserve multicast group support

12 Bug Fix: 1. Fix the bug that too many topology changes in STP. 2. Fix the bug that the fiber port status display link down, even if it links on. 3. Fix the bug that received IGMP queries will exhaust our hardware table. 4. Fix the bug that memory leak problem under log-in attack. 5. Fix the bug that IGMP queries packets come from trunk ports will send back to trunk active port. 6. Fix the bug that device can't get correct "port status detail" of member when using cluster manager from WEB. 7. Classifier precedence will not follow longest prefix match. Known Issues: 1. Management port test fail in 100M long cable. 2. Management port has compatible issue with Cnet Pro 2000 network interface card. 3. The packets which destination address is marked in the filter setting will always send to port Symbol and dribble error packets will count into FCS error counter. 5. Filtering: In some special cases, setting one MAC with discard-source will cause device filter all packets with this MAC, ether source MAC or destination MAC. 6. Do not suggest cooperate LACP with RSTP more than ten ports. 7. Do not support tagged frame forwarding in the Port-Based VLAN. 8. If the contact between RJ45 and wire cable or the wire cable is unstable, the cable diagnostics maybe fail. 9. Modify the high threshold of system FAN RPM to FW upgrade page will be enhanced further. 11. The system-wide rule entries are shared with CIR rate control and policy rules. So you may fail to load max policy rules while enabling CIR rate control on all ports. 12. Ports configured to run RSTP will not synchronize with peers if the port is in BLOCK mode. 13. Packets MAC with tagged vlan id which is not configured in device will be learned. 14. Port configured in fixed-speed mode (AN is disable) for change may not link up. It could be linked up with operation SOP (link down then link up manually) Limitation of Settings: 1. VLAN 1Q static entry Static MAC forwarding entry MAC filtering entry Cluster member Management IP address Protocol based VLAN entries per port 7 7. The number of dhcp snooping can learn is The subnet based vlan can support up to 48 rules. Firmware Upgrade: The ES-3124 uses FTP to upgrade firmware in run-time through its built-in FTP server. You can use any FTP client (for example, ftp.exe in Windows) to upgrade ES The upgrade procedure is as follows: Upgrade ES-3124 FW: C:\> ftp <ES-3124 IP address> User : admin Password: Logged in ftp> put 380TP1C0.bin ras ftp> bye

13 Where User name : the management user name, admin by default Password : the management password, 1234 by default 380TP1C0.bin : the name of firmware file you want to upgrade ras : the internal firmware name in ES-3124 Configuration Upgrade: The ES-3124 uses FTP to upgrade configuration in run-time through its built-in FTP server. You can use any FTP client (for example, ftp.exe in Windows) to upgrade ES The upgrade procedure is as follows: Upgrade ES-3124 configuration: C:\> ftp <ES-3124 IP address> User : admin Password: Logged in ftp> put 380TP1C0.rom rom-0 ftp> bye Where User name : the management user name, admin by default Password : the management password, 1234 by default 380TP1C0.rom : the name of configuration file you want to upgrade rom-0 : the internal configuration name in ES-3124

ZyXEL ES-3124F V3.80(AIV.2)C0 Release Note/Manual Supplement

ZyXEL ES-3124F V3.80(AIV.2)C0 Release Note/Manual Supplement Date: May 10, 2010 This document describes the features in the ES-3124F product for its 3.80(AIV.2)C0 release. Support Platforms: ZyXEL ES-3124F