X64. Operator's Guide TECHNICAL. Example of PC signal

Transcription

1 X64 Operator's Guide TECHNICAL Example of PC signal Resolution (H x V) H. frequency (khz) V. frequency (Hz) Rating Signal mode 720 x VESA TEXT 640 x VESA VGA (60Hz) 640 x VESA VGA (72Hz) 640 x VESA VGA (75Hz) 640 x VESA VGA (85Hz) 800 x VESA SVGA (56Hz) 800 x VESA SVGA (60Hz) 800 x VESA SVGA (72Hz) 800 x VESA SVGA (75Hz) 800 x VESA SVGA (85Hz) 832 x Mac 16 mode 1024 x VESA XGA (60Hz) 1024 x VESA XGA (70Hz) 1024 x VESA XGA (75Hz) 1024 x VESA XGA (85Hz) 1152 x VESA 1152 x 864 (75Hz) 1280 x VESA 1280 x 960 (60Hz) 1280 x VESA SXGA (60Hz) 1280 x VESA SXGA (75Hz) 1280 x VESA SXGA (85Hz) 1600 x VESA UXGA (60Hz) 1280 x VESA W-XGA (60Hz) 1400 x VESA SXGA+ (60Hz) NOTE Be sure to check jack type, signal level, timing and resolution before connecting this projector to a PC. Some PCs may have multiple display screen modes. Use of some of these modes will not be possible with this projector. Depending on the input signal, full-size display may not be possible in some cases. Refer to the number of display pixels above. Although the projector can display signals with resolution up to UXGA (1600x1200), the signal will be converted to the projector s panel resolution before being displayed. The best display performance will be achieved if the resolutions of the input signal and projector panel are identical. Automatically adjustment may not function correctly with some input signals. The image may not be displayed correctly when the input sync signal is a composite sync or a sync on G. 1

2 Initial set signals Initial set signals The following signals are used for the initial settings. The signal timing of some PC models may be different. In such case, adjust the items V POSITION and H POSITION in IMAGE menu. Back porch (B) Front porch (D) Back porch (b) Front porch (d) Data Active video (C) Data H. Sync. V. Sync. Sync (A) Sync (a) Active video (c) computer computer Vertical signal timing (lines) Signal (A) (B) (C) (D) Signal (a) (b) (c) (d) TEXT TEXT VGA (60Hz) VGA (60Hz) VGA (72Hz) VGA (72Hz) VGA (75Hz) VGA (75Hz) VGA (85Hz) VGA (85Hz) SVGA (56Hz) SVGA (56Hz) SVGA (60Hz) SVGA (60Hz) SVGA (72Hz) SVGA (72Hz) SVGA (75Hz) SVGA (75Hz) SVGA (85Hz) SVGA (85Hz) Mac 16" mode Mac 16" mode XGA (60Hz) XGA (60Hz) XGA (70Hz) XGA (70Hz) XGA (75Hz) XGA (75Hz) XGA (85Hz) XGA (85Hz) x x (75Hz) (75Hz) x x (60Hz) (60Hz) SXGA (60Hz) SXGA(60Hz) SXGA (75Hz) SXGA (75Hz) SXGA (85Hz) SXGA (85Hz) UXGA (60Hz) UXGA (60Hz) W-XGA (60Hz) W-XGA (60Hz) SXGA+ (60Hz) SXGA+ (60Hz)

3 Connection to the ports Connection to the ports B C A A COMPUTER IN1, B COMPUTER IN2, C MONITOR OUT D-sub 15pin mini shrink jack terminated (positive) H/V. sync. Signal: TTL level (positive/negative) Composite sync. Signal: TTL level Pin Signal Pin Signal 1 Video Red 10 Ground 2 Video Green 11 (No connection) 3 Video Blue A : SDA (DDC data) 12 4 (No connection) B, C : (No connection) 5 Ground 13 H. sync / Composite sync. 6 Ground Red 14 V. sync. 7 Ground Green A : SCL (DDC clock) 15 8 Ground Blue B, C : (No connection) 9 (No connection) - - 3

4 Connection to the ports (continued) D E F G H COMPONENT VIDEO D Y, E Pb/Cb, F Pr/Cr RCA jack x3 System: 525i(480i), 525p(480p), 625i(576i), 750p(720p),1125i(1080i) Port Signal Y Pb/Cb Pr/Cr G S-VIDEO Mini DIN 4pin jack Pin Signal Ground 4 Ground H VIDEO RCA jack System: NTSC, PAL, SECAM, PAL-M, PAL-N, NTSC4.43 4

5 Connection to the ports (continued) I M J K L I AUDIO IN1, J AUDIO IN2 Ø3.5 stereo mini jack AUDIO IN3 K L, L R RCA jack x2 M AUDIO OUT Ø3.5 stereo mini jack To input SCART RGB signal; ex.: SCART connector (jack) SCART cable (plug) RCA plugs To input SCART RGB signal to the projector, use a SCART to RCA cable. Connect the plugs refer to above ex.. For more reference, please consult your dealer. 5

6 Connection to the ports (continued) O N N USB USB B type jack 4 3 Pin Signal V 2 - Data 3 + Data 4 Ground O CONTROL D-sub 9pin plug About the details of RS-232C communication, please refer to the following page Pin Signal Pin Signal Pin Signal 1 (No connection) 4 (No connection) 7 RTS 2 RD 5 Ground 8 CTS 3 TD 6 (No connection) 9 (No connection) 6

7 Command Control via the Network Command Control via the Network CONTROL port RS-232C cable (cross) RS-232C port of the projector of the computer - (1) (1) CD RD (2) (2) RD TD (3) (3) TD - (4) (4) DTR GND (5) (5) GND - (6) (6) DSR RTS (7) (7) RTS CTS (8) (8) DTS - (9) (9) RI Connecting the cable Turn off the projector and the computer. Connect the CONTROL port of the projector with a RS-232C port of the shown in the previous page. 3. Turn the computer on, and after the computer has started up turn the projector on. Communications setting 19200bps, 8N1 1. Protocol Consist of header (7 bytes) + command data (6 bytes) 2. Header BE + EF CRC_low + CRC_high 3. Command data Command data chart byte_0 byte_1 byte_2 byte_3 byte_4 byte_5 Action Type Setting code low high low high low high Action (byte_0-1) Action Content 1 Set Change setting to desired value. 2 Get Read projector internal setup value. 4 Increment Increment setup value by 1. 5 Decrement Decrement setup value by 1. 6 Execute Run a command. 7

8 Requesting projector status (Get command) (1) Send the following request code from the PC to the projector. Header + Command data ( 02H + 00H + type (2 bytes) + 00H + 00H ) (2) The projector returns the response code 1DH + data (2 bytes) to the PC. Changing the projector settings (Set command) (1) Send the following setting code from the PC to the projector. Header + Command data ( 01H + 00H + type (2 bytes) + setting code (2 bytes)) (2) The projector changes the setting based on the above setting code. (3) The projector returns the response code 06H to the PC. Using the projector default settings (Reset Command) (1) The PC sends the following default setting code to the projector. Header + Command data ( 06H + 00H + type (2 bytes) + 00H + 00H ) (3) The projector returns the response code 06H to the PC. Increasing the projector setting value (Increment command) (1) The PC sends the following increment code to the projector. Header + Command data ( 04H + 00H + type (2 bytes) + 00H + 00H ) (2) The projector increases the setting value on the above setting code. (3) The projector returns the response code 06H to the PC. Decreasing the projector setting value (Decrement command) (1) The PC sends the following decrement code to the projector. Header + Command data ( 05H + 00H + type (2 bytes) + 00H + 00H ) (2) The projector decreases the setting value on the above setting code. (3) The projector returns the response code 06H to the PC. When the projector cannot understand the received command When the projector cannot understand the received command, the error code 15H is sent back to the PC. Sometimes the projector cannot properly receive the command. In such a case, the command is not executed and the error code 15H is sent back to the PC. If this error code is returned, send the same command again. When the projector cannot execute the received command. When the projector cannot execute the received command, the error code 1CH + xxxxh is sent back to the PC. When the data length is greater than indicated by the data length code, the projector ignore the excess data code. Conversely when the data length is shorter than indicated by the data length code, an error code will be returned to the PC. NOTE command or data. Provide an interval of at least 40ms between the response code and any other code. The projector outputs test data when the power supply is switched ON, and when the lamp is lit. Ignore this data. Commands are not accepted during warm-up. 8

9 RS-232C communication command table Names Operation Type Header Command Data CRC Action Type Setting Code Power Set Turn off BE EF A D Turn on BE EF BA D Get BE EF D [Example return] [Off] [On] [Cool down] Input Source Set COMPUTER1 BE EF FE D COMPUTER2 BE EF E D COMPONENT BE EF AE D S-VIDEO BE EF E D VIDEO BE EF E D Get BE EF CD D Error Status Get BE EF D9 D [Example return] [Normal] [Cover error] [Fan error] [Lamp error] [Filter error] (Filter missing error) (Inner Sencer error) BRIGHTNESS Get BE EF D Increment BE EF EF D Decrement BE EF E D BRIGHTNESS Reset Execute BE EF D CONTRAST Get BE EF FD D Increment BE EF B D Decrement BE EF A D CONTRAST Reset Execute BE EF A4 D PICTURE MODE Set NORMAL BE EF F BA CINEMA BE EF B3 F BA DYNAMIC BE EF E3 F BA BOARD(BLACK) BE EF E3 EF BA BOARD(GREEN) BE EF EE BA WHITEBOARD BE EF EE BA DAYTIME BE EF E3 C BA Get BE EF F BA [Example return] [Normal] [Cinema] [Dynamic] [Custom] [BOARD(BLACK) ] [BOARD(GREEN)] [WHITEBOARD] [DAYTIME] GAMMA Set #1 DEFAULT BE EF E A #1 CUSTOM BE EF FD A #2DEFAULT BEEF E A #2 CUSTOM BE EF FC A #3 DEFAULT BE EF E A #3 CUSTOM BE EF FC A #4 DEFAULT BE EF F7 E A #4 CUSTOM BE EF F7 FD A #5DEFAULT BEEF C7EB 0100 A #5 CUSTOM BE EF C7 FF A #6DEFAULT BEEF EA 0100 A #6 CUSTOM BE EF FE A Get BE EF F4 F A (continued on next page) 9

10 RS-232C communication command table (continued) Names Operation Type Header Command Data CRC Action Type Setting Code User Gamma Pattern Set Off BE EF FB FA step gray scale BE EF B FB steps gray scale BE EF B FB Ramp BE EF B FA Get BE EF C8 FA User Gamma Point 1 Get BE EF FE Increment BE EF E FE Decrement BE EF BF FF User Gamma Point 2 Get BE EF F4 FF Increment BE EF FF Decrement BE EF FE User Gamma Point 3 Get BE EF B0 FF Increment BE EF D6 FF Decrement BE EF FE User Gamma Point 4 Get BE EF C FE Increment BE EF A FE Decrement BE EF FB FF User Gamma Point 5 Get BE EF FF Increment BE EF E FF Decrement BE EF F FE User Gamma Point 6 Get BE EF C4 FE Increment BE EF A2 FE Decrement BE EF FF User Gamma Point 7 Get BE EF FE Increment BE EF E6 FE Decrement BE EF FF User Gamma Point 8 Get BE EF C FF Increment BE EF A FF Decrement BE EF CB FE COLOR TEMP Set HIGH BE EF B F B CUSTOM-1 (HIGH) BE EF CB F B MID BE EF B F B CUSTOM-2 (MID) BE EF B F B LOW BE EF B F B CUSTOM-3 (LOW) BE EF AB F B Hi-BRIGHT-1 BE EF B F B CUSTOM-4 (Hi-BRIGHT-1) BE EF FB FF B Hi-BRIGHT-2 BE EF AB F B CUSTOM-5 (Hi-BRIGHT-2) BE EF B FE B Hi-BRIGHT-3 BE EF B F B0 30 0A 00 CUSTOM-6 (Hi-BRIGHT-3) BE EF B FE B0 30 1A 00 Get BE EF C8 F B COLOR TEMP GAIN R Get BE EF F B Increment BE EF F B Decrement BE EF F B COLOR TEMP GAIN G Get BE EF F B Increment BE EF F B Decrement BE EF C7 F B (continued on next page)

11 RS-232C communication command table (continued) Names Operation Type Header Command Data CRC Action Type Setting Code COLOR TEMP GAIN B Get BE EF C F B Increment BE EF EA F B Decrement BE EF B F B COLOR TEMP OFFSET R COLOR TEMP OFFSET G COLOR TEMP OFFSET B Get BE EF F B Increment BE EF F B Decrement BE EF B3 F B Get BE EF F B Increment BE EF F B Decrement BE EF F7 F B Get BE EF BC F B Increment BE EF DA F B Decrement BE EF B F B COLOR Get BE EF B Increment BE EF D Decrement BE EF COLOR Reset Execute BE EF D A TINT Get BE EF Increment BE EF F Decrement BE EF FE TINT Reset Execute BE EF C D B SHARPNESS Get BE EF F Increment BE EF Decrement BE EF SHARPNESS Reset Execute BE EF C4 D MY MEMORY Load Set 1 BE EF E D BEEF ED BEEF ED BEEF FED MY MEMORY Save Set 1 BE EF F2 D BEEF D BEEF D BEEF D PROGRESSIVE Set TURN OFF BE EF A TV BE EF DA FILM BE EF A Get BE EF VIDEO NR Set LOW BE EF MID BE EF D HIGH BE EF Get BE EF ASPECT Set 4:3 BE EF E D :9 BE EF E D :9 BE EF CE D SMALL BE EF FE D NORMAL BE EF E DD Get BE EF AD D (continued on next page) 11

12 RS-232C communication command table (continued) Names Operation Type Header Command Data CRC Action Type Setting Code OVER SCAN Get BE EF Increment BE EF F Decrement BE EF OVER SCAN Reset Execute BE EF EC D V POSITION Get BE EF D Increment BE EF B Decrement BE EF BA V POSITION Reset Execute BE EF E0 D H POSITION Get BE EF F Increment BE EF Decrement BE EF H POSITION Reset Execute BE EF C D H PHASE Get BE EF Increment BE EF F Decrement BE EF FE H SIZE Get BE EF B Increment BE EF D Decrement BE EF H SIZE Reset Execute BE EF D AUTO ADJUST Execute BE EF D A COLOR SPACE Set AUTO BEEF E RGB BE EF E SMPTE240 BE EF E REC709 BE EF FE REC601 BE EF CE Get BE EF D COMPONENT Set COMPONENT BE EF A D SCART RGB BE EF DA D Get BE EF D C-VIDEO FORMAT Set AUTO BE EF A A 00 NTSC BE EF C PAL BEEF SECAM BE EF NTSC4.43 BE EF M-PAL BE EF C N-PAL BE EF Get BE EF S-VIDEO FORMAT Set AUTO BE EF E A 00 NTSC BE EF PAL BEEF SECAM BE EF NTSC4.43 BE EF M-PAL BE EF N-PAL BE EF Get BE EF FRAME LOCK Set TURN OFF BE EF CB D TURN ON BE EF B D Get BE EF F8 D (continued on next page)

13 RS-232C communication command table (continued) Names Operation Type Header Command Data CRC Action Type Setting Code COMPUTER IN1 Set SYNC ON G ON BE EF CE D SYNC ON G OFF BE EF E D Get BE EF D D COMPUTER IN2 Set SYNC ON G ON BE EF D SYNC ON G OFF BE EF A2 D Get BE EF F1 D KEYSTONE V Get BE EF B9 D Increment BE EF DF D Decrement BE EF E D KEYSTONE V Reset Execute BE EF D C AUTO KEYSTONE Execute BE EF E5 D D EXECUTE WHISPER Set NORMAL BE EF B WHISPER BE EF AB Get BE EF MIRROR Set NORMAL BE EF C7 D H:INVERT BE EF D V:INVERT BE EF A7 D H&V:INVERT BE EF D Get BE EF F4 D VOLUME- COMPUTER1 VOLUME- COMPUTER2 VOLUME- COMPONENT Get BE EF CD CC Increment BE EF AB CC Decrement BE EF A CD Get BE EF FD CD Increment BE EF B CD Decrement BE EF A CC Get BE EF CC Increment BE EF CC Decrement BE EF B6 CD VOLUME-S-Video Get BE EF CD Increment BE EF CD Decrement BE EF C2 CC VOLUME-Video Get BE EF CD Increment BE EF CD Decrement BE EF CC MUTE Set TURN OFF BE EF D TURN ON BE EF D6 D Get BE EF D SPEAKER Set TURN ON BE EF FE D C TURN OFF BE EF E D C Get BE EF D D C (continued on next page) 13

14 RS-232C communication command table (continued) Names Operation Type Header Command Data CRC Action Type Setting Code AUDIO-COMPUTER1 Set AUDIO1 BE EF E DC AUDIO2 BE EF E DC AUDIO3 BE EF E DD Turnoff BEEF FEDD Get BE EF CD DD AUDIO-COMPUTER2 Set AUDIO1 BE EF E DD AUDIO2 BE EF AE DD AUDIO3 BE EF E DC Turn off BE EF CE DC Get BE EF FD DC AUDIO-COMPONENT Set AUDIO1 BE EF A2 DC AUDIO2 BE EF DC AUDIO3 BE EF C2 DD Turnoff BEEF DD Get BE EF DD AUDIO-S-VIDEO Set AUDIO1 BE EF D6 DD AUDIO2 BE EF DD AUDIO3 BE EF B6 DC Turnoff BEEF DC Get BE EF DC AUDIO-VIDEO Set AUDIO1 BE EF DD AUDIO2 BE EF DD AUDIO3 BE EF F2 DC Turnoff BEEF DC Get BE EF DC IR REMOTE FREQ. NORMAL IR REMOTE FREQ. HIGH (continued on next page) Set Off BEEF FF3D On BE EF F 3C Get BE EF CC 3D Set Off BEEF C On BE EF D Get BE EF C

15 RS-232C communication command table (continued) Names Operation Type Header Command Data CRC Action Type Setting Code LANGUAGE Set ENGLISH BE EF F7 D FRANÇAIS BE EF D DEUTSCH BE EF D ESPAÑOL BE EF D ITALIANO BE EF D NORSK BE EF A7 D NEDERLANDS BE EF D PORTUGUÊS BE EF C7 D BE EF D BE EF A7 D BE EF DE BE EF D A 00 SVENSKA BE EF C7 D B 00 BE EF F7 D C 00 SUOMI BE EF D D 00 POLSKI BE EF D E 00 TÜRKÇE BE EF D F 00 Get BE EF C4 D MENU POSITION H Get BE EF D Increment BE EF D Decrement BE EF B3 D MENU POSITION H Reset Execute BE EF DC C MENU POSITION V Get BE EF D Increment BE EF D Decrement BE EF F7 D MENU POSITION V Reset Execute BE EF A8 C BLANK Set MyScreen BE EF FB CA ORIGINAL BE EF FB E BLUE BE EF CB D WHITE BE EF B D BLACK BE EF B D Get BE EF D BLANK On/Off Set TURN OFF BE EF FB D TURN ON BE EF B D Get BE EF C8 D START UP Set MyScreen BE EF CB CB ORIGINAL BE EF B D TURN OFF BE EF B D Get BE EF D MyScreen LOCK Set TURN OFF BE EF B EF C TURN ON BE EF AB EE C Get BE EF EF C MESSAGE Set TURN OFF BE EF F D TURN ON BE EF F D Get BE EF BC D AUTO SEARCH Set TURN OFF BE EF B6 D TURN ON BE EF D Get BE EF D (continued on next page) 15

16 RS-232C communication command table (continued) Names Operation Type Header Command Data CRC Action Type Setting Code AUTO KEYSTONE Set TURN OFF BE EF EA D F TURN ON BE EF A D F Get BE EF D9 D F AUTO ON Set TURN OFF BE EF B TURN ON BE EF AB Get BE EF AUTO OFF Get BE EF Increment BE EF E Decrement BE EF BF LAMP TIME Get BE EF C2 FF LAMP TIME Reset Execute BE EF DC FILTER TIME Get BE EF C2 F A FILER TIME Reset Execute BE EF C MY BUTTON-1 COMPUTER1 BE EF A COMPUTER2 BE EF FA COMPONENT BE EF A S-VIDEO BE EF A VIDEO BE EF AA INFORMATION BE EF FA 3E AUTO KEYSTONE EXECUTE BE EF A 3F MY MEMORY BE EF A 3F PICTURE MODE BE EF A 3E FILTER RESET BE EF A 3C VOLUME + BE EF CA 3C VOLUME - BE EF A Get BE EF MY BUTTON-2 COMPUTER1 BE EF C COMPUTER2 BE EF COMPONENT BE EF S-VIDEO BE EF A VIDEO BE EF INFORMATION BE EF F AUTO KEYSTONE EXECUTE BE EF E MY MEMORY BE EF E PICTURE MODE BE EF F6 3F FILTER RESET BE EF C6 3D VOLUME + BE EF D VOLUME - BE EF C Get BE EF F MAGNIFY Get BE EF C D Increment BE EF A D Decrement BE EF CB D FREEZE Set NORMAL BE EF D FREEZE BE EF D Get BE EF B0 D