FlashAir W-02. Firmware Update Tool Ver User s Manual

Transcription

1 FlashAir W-02 Firmware Update Tool Ver User s Manual 1

2 FlashAir firmware update tool Version TOSHIBA CORPORATION Copyright 2017 TOSHIBA CORPORATION, All Rights Reserved. Supported OS: Refer to the Web site. Overview This tool provides a function to update the firmware of the Product to the latest version. This tool may cause all the data and initial settings stored in the Product to be lost. Back up your data on multiple types of storage media before using this tool. After using the tool to update the firmware of the Product, the firmware is the following version. FlashAir firmware version: F19BAW3AW What you need to start A FlashAir W-02 memory card (the Product) Computer on which a supported OS is running SD memory card reader/writer supporting SDHC memory cards (If your computer has an SD memory card slot, confirm that it supports SDHC memory cards) FlashAir firmware update tool 2

3 Operating precautions This tool formats the Product after it updates the firmware, so a smartphone or some other device must be used to do the Product s initial settings to enable wireless communication. Data cannot be written to the Product while you are doing the initial settings. After you do the initial settings, turn off the digital camera, take out the Product, and insert the Product again. Initial settings are required every time the Product is formatted by a digital camera or some other device. Data cannot be written to the Product while you are doing the initial settings. After you do the initial settings, turn off the digital camera, take out the Product, and insert the Product again. Installation of FlashAir firmware update tool to a computer Download the FlashAir firmware update tool (FAFWUpdateToolV2_v20004_a.zip) from the download site, and save it in any folder you like on your computer. Right-click the downloaded "FAFWUpdateToolV2_v20004_a.zip" and select "Extract All...". Select a destination to save the extracted folder and click "Extract". Double-clicking FAFWUpdateToolV2_v20004_a.exe starts the installation on your computer. 3

4 Choose the appropriate language and Click Next >. 4

5 After preparation of installation is finished, the following screen is displayed, click Next >. Choose a location for installing the software and click Next >. In this manual, the location is not changed. 5

6 After preparation of installation is finished, the below screen be displayed. Then, click Install>. After installation is complete, the following screen is displayed. Click Finish to exit the wizard. 6

7 After the installation is complete, a FAFWUpdateToolV2 icon appears on your computer s desktop. The FlashAir firmware tool is now installed on your computer. 7

8 How to update the firmware Insert the Product into a SD card slot of your computer that supports SDHC, or insert the Product into an SDHC memory card reader/writer that is connected to your computer on which a supported OS is running. When the following screen is displayed, use Explorer to open the folder and browse is contents. Access the product from your computer to confirm that the connection was done correctly. 8

9 To start the tool, double click FAFWUpdateToolV2.exe. The drive in which the Product is mounted is displayed in the Drive box. In the following example, the Product is mounted in drive F. Select the drive on which the Product is mounted. Click the Update button. 9

10 The FlashAir firmware update tool will check the version of FlashAir W-02 before the update. If the version of the Product cannot be confirmed, the following dialog is displayed. Remove the Product by using the Safe to remove hardware feature. Remove the Product from the SD card slot. Then insert the Product in the SD card slot again after five (5) seconds, and click OK. After a while, the following dialog is displayed. When the following dialog is displayed, click the OK button. Writing of the software to update the Product starts. While the following dialog is displayed, do not remove the Product and do not turn off the computer, doing so causes the update to fail and prevents the Product from starting. 10

11 When the following dialog is displayed, remove the Product by using the Safe to remove hardware feature. Insert the Product again, and click the OK button. When the following window is displayed, remove the Product from the SD card slot. Then insert the Product in the SD card slot again after five (5) seconds, and click OK. When the update starts, a progress bar is displayed and the following dialog box is displayed when the update is finished. 11

12 After the following dialog box is displayed, remove the Product from the SD card slot. Then insert the Product into the SD card slot again after five (5) seconds, and click OK. The progress bar is displayed again and when the update is finished, the following window is displayed. After the following dialog box is displayed, remove the Product from the SD card slot. Then, insert the Product into the SD card slot again after five (5) seconds, and click OK. The progress bar is displayed again and the following window is displayed for the version check whether the update has finished normally. After the version check is completed, the following window is displayed. After the update is finished, do the initial settings according to the supplementary manual attached to the Product. This completes the product s firmware update. 12