High-Flying HF-LPT120. Low Power WiFi Module User Manual. Overview of Characteristic V 1.4. HF-LPT120 Low Power WiFi Module User Manual

Size: px

Start display at page:

Download "High-Flying HF-LPT120. Low Power WiFi Module User Manual. Overview of Characteristic V 1.4. HF-LPT120 Low Power WiFi Module User Manual"

Lucinda Pope
5 years ago
Views:

1 HF-LPT120 Low Power WiFi Module User Manual Overview of Characteristic V 1.4 Support IEEE802.11b/g/n Wireless Standards Based on Self-developed High Cost Effective SOC Support UART/GPIO Data Communication Interface Support Work As STA/AP Mode Support Smart Link Function (APP program provide) Support Wireless and Remote Firmware Upgrade Function support WPS Function Support External I-PEX or Internal PCB Antenna Option Single +3.3V Power Supply Smallest Size: 22mm x 13.5mm x 6mm, 1x10 2mm Connector FCC/CE Certificated Shanghai Electronics Technology Co., Ltd(

2 TABLE OF CONTENTS LIST OF FIGURES... 4 LIST OF TABLES... 5 HISTORY PRODUCT OVERVIEW General Description Device Features Device Paremeters Key Application Hardware Introduction Pins Definition Electrical Characteristics Mechanical Size On-board PCB Antenna External Antenna Evaluation Kit Order Information Typical Application Hardware Typical Application Internal PCB Antenna Typical Application PACKAGE INFORMATION Recommended Reflow Profile Device Handling Instruction (Module IC SMT Preparation) Shipping Information...21 APPENDIX A: HW REFERENCE DESIGN...22 APPENDIX B: HTTP PROTOCOL TRANSFER...23 B.1. HTTP AT command(reserved)...23 B.1.1 AT+HTTPURL...23 B.1.2 AT+HTTPTP...23 B.1.3 AT+HTTPPH...23 B.1.4 AT+HTTPCN...24 B.1.5 AT+HTTPUA...24 B.1.6 AT+HTTPDT...24 B.2. HTTP Example...24 B.3. Sending HTTP Raw Data in Throughput Mode(Recommend)...25 B.4. Sending HTTP Request By AT Command...26 APPENDIX C:REFERENCES...28 C.1. Mass Production Tool...28 Shanghai Electronics Technology Co., Ltd(

3 C.2.SmartLink APP V7 Config Tool...28 C.3.EVK Quick Start Guide...28 C.4.Module Upgrade...28 APPENDIX D: CONTACT INFORMATION...29 Shanghai Electronics Technology Co., Ltd(

4 LIST OF FIGURES Figure 1. HF-LPT120 Pins Map... 9 Figure 2. HF-LPT120 Mechanical Dimension...11 Figure 3. HF-LPT120A Mechanical Dimension...11 Figure 4. Suggested Module Placement Region...12 Figure 5. HF-LPT120 External Antenna picture...12 Figure 6. HF-LPT120 Evaluation Kit...13 Figure 7. LPT120/LPT220 EVK Type Figure 8. HF-LPT120 Order Information...15 Figure 9. HF-LPT120A Order Information...15 Figure 10. HF-LPT120 Hardware Typical Application...16 Figure 11. HF-LPT120 Antenna...17 Figure 12. HF-LPT120 Antenna radiation pattern...17 Figure 13. HF-LPT120 XY plane radiation pattern...18 Figure 14. HF-LPT120XZ plane radiation pattern...18 Figure 15. HF-LPT120YZ plane radiation pattern...18 Figure 16. Reflow Soldering Profile...20 Figure 17. Shipping Information...21 Shanghai Electronics Technology Co., Ltd(

5 LIST OF TABLES Table 1 HF-LPT120 Module Technical Specifications... 8 Table 2 HF-LPT120 Pins Definition... 9 Table 3 Absolute Maximum Ratings:...10 Table 4 Power Supply & Power Consumption:...10 Table 5 HF-LPT120 External Antenna Parameters...12 Table 6 HF-LPT120 Evaluation Kit Interface Description...14 Table 11 Reflow Soldering Parameter...20 Shanghai Electronics Technology Co., Ltd(

6 HISTORY Ed. V1.02 Ed. V First Version Modify IO PIN Description. Ed. V Change Module PCB. Ed. V1.1 Ed. V1.1.1 Ed. V Update AT command supported by version firmware Add HF-LPT100-A Type Modify HF-LPT100-A to HF-LPT100A Type, Update AT command supported by version firmware. Add support for AT+E AT+SOCKB AT+TCPDISB AT+TCPTOB AT+TCPLKB AT+WALK AT+WALKIND command. Correct the AT+NETP command description. Ed. V Update AT command supported by version firmware. Add support for AT+MAXSK AT+WAPMXSTA command. Update AT+NETP AT+UART command. All the reserved function is not supported yet. See appendix C to get new firmware. Ed. V Update AT command supported by version firmware. Add support for AT+UPURL. Modify AT+UART flow control, modify AT+DISPS function. Update the new EVK data. See appendix C for new firmware. See LPB120 manual for the module usage and AT command list. Shanghai Electronics Technology Co., Ltd(

7 1. PRODUCT OVERVIEW 1.1. General Description The HF-LPT120 is a fully self-contained small form-factor, single stream, b/g/n Wi-Fi module, which provide a wireless interface to any equipment with a Serial/PWM interface for data transfer.hf- LPT120 integrate MAC, baseband processor, RF transceiver with power amplifier in hardware and all Wi-Fi protocol and configuration functionality and networking stack, in embedded firmware to make a fully self-contained b/g/n Wi-Fi solution for a variety of applications. The HF-LPT120 employs the world's lowest power consumption embedded architecture. It has been optimized for all kinds of client applications in the home automation, smart grid, handheld device, personal medical application and industrial control that have lower data rates, and transmit or receive data on an infrequent basis. The HF-LPT120 integrates all Wi-Fi functionality into a low-profile, 22mm x 13.5mm x 6mm module package that can be easily mounted on main PCB with application specific circuits. Also, module provides built-in antenna, external antenna option Device Features Single stream 2.4 GHz with support for WEP security mode as well as WPA/WPA2 Based on Self-developed High Cost Performance SOC Includes all the protocol and configuration functions for Wi-Fi connectivity. Support STA/AP Mode Support Smart Link Function Support Wireless and Remote Firmware Upgrade Function Support External I-PEX or Internal PCB antenna connector options. Compact surface mount module 22mm x 13.5mm x 6mm Single supply 3.3V operation. FCC/CE Certified. RoHS Compliant. Shanghai Electronics Technology Co., Ltd(

8 1.1.2 Device Paremeters Table 1 HF-LPT120 Module Technical Specifications Class Item Parameters Certification FCC/CE Wireless Parameters Hardware Parameters Software Parameters Key Application Wireless standard b/g/n Frequency range 2.412GHz-2.484GHz b: +16 +/-2dBm (@11Mbps) Transmit Power g: +14 +/-2dBm (@54Mbps) n: +13 +/-2dBm (@HT20, MCS7) b: -93 dbm (@11Mbps,CCK) Receiver Sensitivity g: -85 dbm (@54Mbps, OFDM) n: -82 dbm (@HT20, MCS7) Antenna Option External:I-PEX Connector Internal:PCB Printed Antenna Data Interface UART GPIO Operating Voltage 2.95~3.6V Operating Current Peak [Continuous TX]: ~280mA Average. ~20mA Operating Temp Storage Temp Dimensions and Size 22mm x 13.5mm x 6mm External Interface Network Type Security Mechanisms Encryption Update Firmware Customization Network Protocol User Configuration 1x10, 2mm DIP STA /AP WEP/WPA-PSK/WPA2-PSK WEP64/WEP128/TKIP/AES Local Wireless, Remote Support customization IPv4, TCP/UDP/HTTP AT+instruction set. Android/ ios Smart Link APP tools Remote equipment monitoring Asset tracking and telemetry Security Industrial sensors and controls Home automation Medical devices Shanghai Electronics Technology Co., Ltd(

1.2. Hardware Introduction 1.2.1. Pins Definition Table 2 Figure 1. HF-LPT120 Pins Map HF-LPT120 Pins Definition Pin Description Net Name Signal Type 1 Ground GND Power Comments 2 +3.

9 1.2. Hardware Introduction Pins Definition Table 2 Figure 1. HF-LPT120 Pins Map HF-LPT120 Pins Definition Pin Description Net Name Signal Type 1 Ground GND Power Comments V Power DVDD Power 3.3V@300mA 3 Restore Configuration nreload I/O,PU Can be configured as GPIO_2 Detailed functions see <Notes> 4 Module Reset EXT_RESETn I,PU Low effective reset input. 5 UART0 UART0_RX I GPIO_19 6 UART0 UART0_TX O,PU GPIO_20 7 UART1_TXD GPIO_5 I/O GPIO_5,UART1_TXD UART1 Debug Output 8 UART1_RXD GPIO_6 I/O GPIO_6, UART1_RXD UART1 Debug Input 9 GPIO_3 nready I/O Can be configured as nready,gpio 10 GPIO_15 nlink I/O Can be configured as nlink,gpio Detailed functions see <Notes> I Input, O Output,PU Internal Pullup Resistor; I/O: Digital I/O;Power Power <Notes> nreload Pin (Button) function: 1. When this pin is set to low during module boot up, the module will enter wireless firmware and config upgrade mode. This mode is used for customer manufacture. Shanghai Electronics Technology Co., Ltd(

10 (See Appendix D to download software tools for customer batch configuration and upgrade firmware during mass production) 2. After module is powered up, short press this button ( Low < 2s ) to make the module go into Smart Link config mode, waiting for APP to set password and other information. (See Appendix D to download SmartLink APP) 3. After module is powered up, long press this button ( Low > 4s ) to make the module recover to factory setting. strongly suggest customer fan out this pin to connector or button for Manufacture and Smart Link application. nlink Pin (LED) function: 1. At wireless firmware and config upgrade mode, this LED used to indicate configure and upgrade status. 2. At Smart Link config mode, this LED used to indicate APP to finish setting. 3. At normal mode, it s Wi-Fi link status indicator strongly suggest customer fan out this pin to LED Electrical Characteristics Table 3 Absolute Maximum Ratings: Parameter Condition Min. Typ. Max. Unit Storage temperature range C Maximum soldering temperature IPC/JEDEC J-STD C Supply voltage V Voltage on any I/O pin V ESD (Human Body Model HBM) TAMB=25 C 2.5 KV ESD (MM) TAMB=25 C 0.25 KV Table 4 Power Supply & Power Consumption: Parameter Condition Min. Typ. Max. Unit Operating Supply voltage V Supply current, peak Continuous Tx 280 ma Supply current, IEEE PS DTIM=100ms 20 ma Shanghai Electronics Technology Co., Ltd(

11 Mechanical Size HF-LPT120 modules physical size (Unit: mm) as follows: Figure 2. HF-LPT120 Mechanical Dimension Figure 3. HF-LPT120A Mechanical Dimension Shanghai Electronics Technology Co., Ltd(

1.2.4. On-board PCB Antenna HF-LPT120 module support internal on-board PCB antenna option.

GND net; Antenna must away from metal or high components at least 10mm; Antenna can t be shielded by any metal enclosure; Figure 4.

12 On-board PCB Antenna HF-LPT120 module support internal on-board PCB antenna option. When customer select internal antenna, you shall comply with following antenna design rules and module location suggestions: For customer PCB, RED color region (8x10mm) can t put componet or paste GND net; Antenna must away from metal or high components at least 10mm; Antenna can t be shielded by any metal enclosure; Figure 4. Suggested Module Placement Region suggest HF-LPB100 module better locate in following region at customer board, which to reduce the effect to antenna and wireless signal, and better consult technical people when you structure your module placement and PCB layout External Antenna HF-LPT120 supports two way of external antenna as the following picture show, The I-PEX interface or the PAD interface(remove the I-PEX connector). The user may choose one of them. If user select external antenna, HF-LPT120 modules must be connected to the 2.4G antenna according to IEEE b/g/n standards. The antenna parameters required as follows: Item Figure 5. Table 5 Frequency range Impedance VSWR Return Loss Connector Type HF-LPT120 External Antenna picture HF-LPT120 External Antenna Parameters Parameters 2.4~2.5GHz 50 Ohm 2 (Max) -10dB (Max) I-PEX or populate directly Shanghai Electronics Technology Co., Ltd(

1.2.6. Evaluation Kit provides the evaluation kit to promote user to familiar the product and develop the detailed application.

some functional tests. The EVK support.5v DC power supply. Figure 6. HF-LPT120 Evaluation Kit Figure 7.

13 Evaluation Kit provides the evaluation kit to promote user to familiar the product and develop the detailed application. The evaluation kit shown as below, user can connect to HF-LPT120 module with the RS- 232 UART, or Wireless interface to configure the parameters, manage the module or do the some functional tests. The EVK support.5v DC power supply. Figure 6. HF-LPT120 Evaluation Kit Figure 7. LPT120/LPT220 EVK Type 2 Notes: User need download USB to UART port driver from web or contact with technical support people for more detail.(there are two kinds of EVK provided as the above picture, mostly we will provide the EVK Type 2) Shanghai Electronics Technology Co., Ltd(

14 The external interface description for evaluation kit as follows: Table 6 HF-LPT120 Evaluation Kit Interface Description Function Name Description External Interface Button RS232 DC5V nreload Main data/command RS-232 interface DC jack for power in, 5V input. Restore factory default configuration after push this pin more than 4s. See Shanghai Electronics Technology Co., Ltd(

15 Order Information Base on customer detailed requirement, HF-LPT120 series modules provide different variants and physical type for detailed application. Figure 8. HF-LPT120 Order Information Figure 9. HF-LPT120A Order Information Shanghai Electronics Technology Co., Ltd(

16 1.3. Typical Application Hardware Typical Application Notes: Figure 10. HF-LPT120 Hardware Typical Application nreset- Module hardware reset signal. Input. Logics 0 effective. There is pull-up resister internal and no external pull-up required. When module power up or some issue happened, MCU need assert nrst signal 0 at least 10ms, then set 1 to keep module fully reset. nready- Module boot up ready signal. Output. Logics 0 effective. The module will output 0 after normal boot up. This signal used to judge if module finish boot up and ready for application or working at normal mode. If nready function not required, can leave this pin open. nreload- Module restore to factory default configuration.input. Logics 0 effective. (This pin is recommend to connect to button, is used to enter wireless upgrade mode) User can de-assert nreload signal 0 more than 4s through button or MCU pin, then release, module will restore to factory default configuration and re-start boot up process.. If nreload function not required, can leave this pin open. UART0_TXD/RXD- UART port data transmit and receive signal. nlink- Module WIFI connection status indication. Output. Shanghai Electronics Technology Co., Ltd(

(This pin is recommend to connect to LED, indicate status when the module in wireless upgrade mode) When module connects to AP (AP associated), this pin

If nlink function not required, can leave this pin open. 1.4. Internal PCB Antenna Antenna radiation efficiency 49.2% Figure 11.

17 (This pin is recommend to connect to LED, indicate status when the module in wireless upgrade mode) When module connects to AP (AP associated), this pin will output 0. This signal used to judge if module already at WiFi connection status. Thers is pull-up resister internal and no external pull-up required. If nlink function not required, can leave this pin open Internal PCB Antenna Antenna radiation efficiency 49.2% Figure 11. HF-LPT120 Antenna Figure 12. HF-LPT120 Antenna radiation pattern XY plane maximum gain:-1.21db, minimum gain: dB Shanghai Electronics Technology Co., Ltd(

18 Figure 13. HF-LPT120 XY plane radiation pattern XZ plane maximum gain:-0.99db, minimum gain:-1.6db Figure 14. HF-LPT120XZ plane radiation pattern YZ plane maximum gain:-0.99db, minimum gain:-11.52db Figure 15. HF-LPT120YZ plane radiation pattern Shanghai Electronics Technology Co., Ltd(

19 1.5. Typical Application Refer to HF-LPB120 user manual for detailed application and module usage. Shanghai Electronics Technology Co., Ltd(

20 2. PACKAGE INFORMATION 2.1. Recommended Reflow Profile Figure 16. Reflow Soldering Profile Table 11 Reflow Soldering Parameter NO. Item Temperature (Degree) Time(Sec) 1 Reflow Time Time of above ~55 sec 2 Peak-Temp 260 max Note: 1. Recommend to supply N2 for reflow oven. 2. N2 atmosphere during reflow (O2<300ppm) 2.2. Device Handling Instruction (Module IC SMT Preparation) 1. Shelf life in sealed bag: 12 months, at <30 and <60% relative humidity (RH) 2. After bag is opened, devices that will be re-baked required after last baked with window time 168 hours. 3. Recommend to oven bake with N2 supplied 4. Recommend end to reflow oven with N2 supplied 5. Baked required with 24 hours at before rework process 6. Recommend to store at 10% RH with vacuum packing 7. If SMT process needs twice reflow: (1) Top side SMT and reflow (2) Bottom side SMT and reflow Case 1: Wifi module mounted on top side. Need to bake when bottom side process over 168 hours window time, no need to bake within 168 hours Case 2: Wifi module mounted on bottom side, follow normal bake rule before process Note: Window time means from last bake end to next reflow start that has 168 hours space. Shanghai Electronics Technology Co., Ltd(

21 2.3. Shipping Information TRAY Size: 350*260*20 mm BOX Size: 350*260*160 mm (inside) Note: 1 tray = 20*6pcs = 120 pcs 1 box = 8 trays = 8 * 120 pcs = 960pcs Figure 17. Shipping Information Shanghai Electronics Technology Co., Ltd(

22 APPENDIX A: HW REFERENCE DESIGN Detailed HF-LPT120 Evluation Board design source files, pls access web download page or contact with technical support people to acquire. Shanghai Electronics Technology Co., Ltd(

23 APPENDIX B: HTTP PROTOCOL TRANSFER HF-LPB120 module support http data transfer in command mode. If any detailed HTTP protocol, contact us and we may support customization. B.1. HTTP AT command(reserved) B.1.1 B.1.2 B.1.3 AT+HTTPURL Function:Set /Query HTTP server IP address and Port Number. Format: Query Operation AT+HTTPURL<CR> +ok=<ip,port><cr><lf><cr><lf> Set Operation AT+HTTPURL=<IP,Port><CR> +ok<cr><lf><cr><lf> Parameters: AT+HTTPTP IP:IP address. Port:Port number. Function:Set /Query HTTP request type Format: Query Operation AT+HTTPTP<CR> +ok=<type><cr><lf><cr><lf> Set Operation AT+HTTPTP=<Type><CR> +ok<cr><lf><cr><lf> Parameters: Type:GET(default) or POST AT+HTTPPH Function:Set/Query HTTP protocol header path. Format: Query Operation AT+HTTPPH<CR> +ok=<path><cr><lf><cr><lf> Set Operation AT+HTTPPH=<Path><CR> +ok<cr><lf><cr><lf> Parameters: Shanghai Electronics Technology Co., Ltd(

24 Path:Max length is 50 bytes. B.1.4 B.1.5 B.1.6 AT+HTTPCN Function:Set/Query Connection of HTTP protocol header Format: Query Operation AT+HTTPCN<CR> +ok=<connection><cr><lf><cr><lf> Set Operation AT+HTTPCN=<Connection><CR> +ok<cr><lf><cr><lf> Parameters: AT+HTTPUA Connection:Max length is 20 bytes. Function:Set/Query User-Agent of HTTP protocol header. Format: Query Operation AT+HTTPUA<CR> +ok=<parameter><cr><lf><cr><lf> Set Operation AT+HTTPUA=<Parameter><CR> +ok<cr><lf><cr><lf> Parameters: AT+HTTPDT Parameter:Max length is 20 bytes. Function: Send HTTP request or data. Format: Set Operation AT+HTTPDT=<Data><CR> +ok<cr><lf><cr><lf> Parameters: Data:HTTP request data, send AT+HTTPDT directly if no data to be sent. B.2. HTTP Example HTTP parameter settings are as follows: AT+HTTPURL= ,80 AT+HTTPTP=POST AT+HTTPPH=/abcd AT+HTTPCN= keep-alive AT+HTTPUA= lwip1.3.2 Set HTTP server address and port Set HTTP request type Set HTTP protocol header path Set HTTP Connection area Set HTTP User-Agent area Shanghai Electronics Technology Co., Ltd(

25 If send AT+HTTPDT, the data packet will be sent as the following instance including the two new line: POST /abcd HTTP/1.1 Connection:keep-alive User-Agent:lwip1.3.2 Content-Length:0 Host: :8999 If send AT+HTTPDT=abcd, the data packet will be sent as the following instance: POST /abcd HTTP/1.1 Connection:keep-alive User-Agent:lwip1.3.2 Content-Length:4 Host: :8999 abcd The data received from HTTP server will be output to serial port and end with +ok. If the module hasn t received data from HTTP server for 5 second, it will cut the TCP link with HTTP server. B.3. Sending HTTP Raw Data in Throughput Mode(Recommend) Step 1 Configure HTTP server information Step 2 Configure module connecting to router AP and reboot. Step 3 Sending HTTP raw data via UART, end the data with<cr><lf><cr><lf> Shanghai Electronics Technology Co., Ltd(

26 B.4. Sending HTTP Request By AT Command Step 1 Configure HTTP AT command. SOCKB must set as None. Shanghai Electronics Technology Co., Ltd(

27 Step 2 Configure module connecting to router AP and reboot. Step 3 Send HTTP request Shanghai Electronics Technology Co., Ltd(

28 APPENDIX C:REFERENCES C.1. Mass Production Tool Download Address: 4fb4-a5e5-c3403f09ab08&comp_stats=comp-FrontDownloads_list01-dc.html C.2.SmartLink APP V7 Config Tool IOS Platform : 2ad2954b3b50&comp_stats=comp-FrontDownloads_list01-dc.html Android Platform: C.3.EVK Quick Start Guide Download Address: C.4.Module Upgrade Download Address: Shanghai Electronics Technology Co., Ltd(

29 APPENDIX D: CONTACT INFORMATION Address: Room 1002,Building 1,No.3000,Longdong Avenue,Pudong New Area,Shanghai,China, Web: Service Online: / Sales Contact: For more information about modules, applications, and solutions, please visit our web site <END OF DOCUMENT> Copyright, May, 2011 The information disclosed herein is proprietary to and is not to be used by or disclosed to unauthorized persons without the written consent of. The recipient of this document shall respect the security status of the information. The master of this document is stored on an electronic database and is write-protected and may be altered only by authorized persons at. Viewing of the master document electronically on electronic database ensures access to the current issue. Any other copies must be regarded as uncontrolled copies. Shanghai Electronics Technology Co., Ltd(

HF-LPB300 Low Power WiFi Module User Maunal V 1.0

HF-LPB300 Low Power WiFi Module User Maunal V 1.0-1 - TABLE OF CONTENTS LIST OF FIGURES... 3 LIST OF TABLES... 3 HISTORY... 3 PRODUCT OVERVIEW... 4 General Description... 4 Device Features... 4 Device