Home Audio System CMT-SX7/SX7B. Operating Instructions. Getting started. About SongPal. Listening to a CD. Listening to the radio

Transcription

1 Home Audio System Operating Instructions Getting started About SongPal Listening to a CD Listening to the radio Refer to the Wi-Fi Startup Guide (separate document) for how to listen to music stored in your PC or other device over your Wi-Fi network. Listening to a file on a USB device Listening to music of an iphone/ipad/ipod Listening to music with connected components Listening to music through a BLUETOOTH connection Listening to music via a Wi- Fi network Additional information Troubleshooting Precautions/Specifications CMT-SX7/SX7B

2 2 GB WARNING To reduce the risk of fire, do not cover the ventilation opening of the appliance with newspapers, tablecloths, curtains, etc. Do not expose the appliance to naked flame sources (for example, lighted candles). To reduce the risk of fire or electric shock, do not expose this appliance to dripping or splashing, and do not place objects filled with liquids, such as vases, on the appliance. As the main plug is used to disconnect the unit from the mains, connect the unit to an easily accessible AC outlet. Should you notice an abnormality in the unit, disconnect the main plug from the AC outlet immediately. Do not install the appliance in a confined space, such as a bookcase or built-in cabinet. Do not expose batteries or appliances with battery-installed to excessive heat, such as sunshine and fire. The unit is not disconnected from the mains as long as it is connected to the AC outlet, even if the unit itself has been turned off. Excessive sound pressure from earphones and headphones can cause hearing loss. Indoor use only. Recommended cables Properly shielded and grounded cables and connectors must be used for connection to host computers and/or peripherals. CAUTION The use of optical instruments with this product will increase eye hazard. This appliance is classified as a CLASS 1 LASER product. This marking is located on the rear exterior. For customers in Australia and New Zealand It should be installed and operated with at least 20 cm and more between the radiator and person's body (excluding extremities: hands, wrists, feet and ankles). For customers in Europe Notice for customers: the following information is only applicable to equipment sold in countries applying EU directives. This product has been manufactured by or on behalf of Sony Corporation, Konan Minato-ku Tokyo, Japan. Inquiries related to product compliance based on European Union legislation shall be addressed to the authorized representative, Sony Belgium, bijkantoor van Sony Europe Limited, Da Vincilaan 7-D1, 1935 Zaventem, Belgium. For any service or guarantee matters, please refer to the addresses provided in the separate service or guarantee documents. This product is intended to be used in the following countries: AT, BE, BG, HR, CY, CZ, DK, EE, FI, FR, DE, GR, HU, IS, IE, IT, LV, LI, LT, LU, MT, NL, NO, PL, PT, RO, SK, SI, ES, SE, CH, GB, AL, BA, MK, MD, RS, ME, Kosovo Hereby, Sony Corp., declares that this equipment is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. For details, please access the following URL: MHz band is restricted to indoor operations only. This equipment has been tested and found to comply with the limits set out in the EMC regulation using a connection cable shorter than 3 meters. Disposal of waste batteries and electrical and electronic equipment (applicable in the European Union and other European countries with separate collection systems) This symbol on the product, the battery or on the packaging indicates that the product and the battery shall not be treated as household waste. On certain batteries this symbol might be used in combination with a chemical symbol. The chemical symbols for mercury (Hg) or lead (Pb) are added if the battery contains more than % mercury or 0.004% lead. By ensuring these products and batteries are disposed of correctly, you will help prevent potentially negative consequences for the environment and human health which could otherwise be caused by inappropriate waste handling. The recycling of the materials will help to conserve natural resources. In case of products that for safety, performance or data integrity reasons require a permanent connection with an incorporated battery, this

3 battery should be replaced by qualified service staff only. To ensure that the battery and the electrical and electronic equipment will be treated properly, hand over these products at end-of-life to the applicable collection point for the recycling of electrical and electronic equipment. For all other batteries, please view the section on how to remove the battery from the product safely. Hand the battery over to the applicable collection point for the recycling of waste batteries. For more detailed information about recycling of this product or battery, please contact your local Civic Office, your household waste disposal service or the shop where you purchased the product or battery. The adaptor is not for the use in Chile. Please use this adaptor in the countries where it is necessary. Before operating this system Malfunctions that occur during the normal use of the system will be repaired by Sony in accordance with the conditions defined in the limited warranty for this system. However, Sony will not be liable for any consequences arising from a failure to play caused by a damaged or malfunctioning system. Music discs encoded with copyright protection technologies This product is designed to playback discs that conform to the Compact Disc (CD) standard. Recently, various music discs encoded with copyright protection technologies are marketed by some record companies. Please be aware that among those discs, there are some that do not conform to the CD standard and may not be playable by this product. on DualDiscs A DualDisc is a two sided disc product which mates DVD recorded material on one side with digital audio material on the other side. However, since the audio material side does not conform to the Compact Disc (CD) standard, playback on this product is not guaranteed. 3 GB

4 Documents provided Operating Instructions (this document) Explains important safety information, BLUETOOTH connection method, troubleshooting, etc. Wi-Fi Startup Guide (separate document) Explains how to listen to music stored in your computer or other device over your Wi-Fi network. Help Guide (web document for a PC/ smartphone) Explains details about the system; network connection and playback method with each OS/ device, wireless LAN connection, etc. 4 GB

5 Table of Contents Before operating this system...3 Documents provided... 4 Getting started Location and function of controls... 8 Inserting the batteries...11 About SongPal What you can do with SongPal Listening to a CD Playing a CD-DA/MP3 disc To change the play mode Creating your own program (Program Play) Listening to the radio Tuning in a radio station...16 Presetting radio stations Running the DAB Automatic Scan manually (CMT-SX7B only) Listening to a file on a USB device Playing a file on a USB device...18 Connecting a USB device to the USB port on the front of the unit...18 Connecting a USB device to the USB port on the rear of the unit...19 Playable audio formats...19 Listening to music of an iphone/ipad/ipod Playing via USB connection Playing via wireless connection (AirPlay) GB

6 Listening to music with connected components Playing back the music of connected components...21 Playing a component connected to the OPTICAL IN jack...21 Playing a component connected to the LINE IN jack...21 Listening to music through a BLUETOOTH connection Pairing the system with a BLUETOOTH device and listening to music Listening to music through a registered device Listening to music by one-touch action (NFC) Playing with high quality sound codec (AAC/LDAC) Listening to music via a Wi-Fi network Selecting the method of network connection Connecting with a computer Listening to the same music from the multiple speakers (SongPal Link function) Listening to an Internet music service (Google Cast) Listening to an Internet music service (Spotify) Additional information Setting the Automatic Standby function Setting the BLUETOOTH/Network Standby mode Setting the wireless signal ON/OFF...31 Adjusting the sound...31 Setting the clock Using the timers Setting the Sleep Timer Setting the Play Timer Updating the software Method 1: Automatic update via the Internet Method 2: Manual update via the Internet Method 3: Manual update via a USB flash drive When the update via a network has failed GB

7 Troubleshooting Troubleshooting...37 Messages Precautions/Specifications Precautions Compatible devices and versions iphone/ipad/ipod or itunes DLNA device USB device BLUETOOTH device BLUETOOTH wireless technology...47 Specifications GB

8 Getting started Location and function of controls This manual mainly explains operations using the remote, but the same operations can also be performed using the buttons on the unit having the same or similar names. Unit (front) 8 GB / (power) button Use to turn the power on or off. Standby indicator Lights in yellow-green when the power is turned on. Turns off when the power is turned off. The indicator flashes in red if the system detects an abnormality (page 37). When the system in BLUETOOTH/ Network Standby mode, the indicator lights up in orange. (play/pause) button Use to start or pause playback. Display window N-Mark Place a smartphone/tablet equipped with the NFC function close to this mark to perform BLUETOOTH registration, connection or disconnection by a onetouch action (page 24). MENU button Use to display the menu. Press / to select the items in the menu. BACK button Use to go back to the previous display. / (previous/next) /TUNING /+ dial Use to cue to the beginning of a track or file. Use to tune in a desired radio station. PUSH ENTER button Use to operate as the ENTER button. Remote sensor VOLUME dial Use to adjust the volume. (open/close) button Use to open or close the disc tray. Disc tray Set a CD with the label side facing upward.

9 (USB FRONT) port Connect a USB device (page 18). (headphones) jack Use to connect headphones. Remote / (previous/next, PRESET /+) buttons Use to cue to the beginning of a track or file. Use to select a preset number of the radio station tuned in. / (fast-rewind/fast-forward, TUNING /+) buttons Use to fast-rewind or fast-forward a track or file. Use to tune-in a desired radio station. (play/pause) button Use to start or pause playback. CLEARAUDIO+ button Set the sound to Sony s recommended settings. Getting started / (power) button Use to turn the power on or off. / /ENTER button Press / to select an item, then press ENTER to enter. Use / to select a folder (album) on an MP3 disc or USB device. (volume) +/ button Use to adjust the volume. (muting) button Use to turn off the sound temporarily. Press the button again to restore the sound. (stop) button Use to stop playback. BACK button Use to return to the previous status. MENU button Use to display the menu. Press / to select the items in the menu. FUNCTION button Press to change the functions. Each press changes to the next function in the following sequence: CD USB FRONT USB REAR BLUETOOTH DAB* TUNER FM TUNER AM* OPTICAL IN LINE IN NETWORK * DAB is available for CMT-SX7B only, and TUNER AM is for CMT-SX7 only. DISPLAY button Use to change the information displayed in the display window when the power is on. An underscore _ is displayed in the place of an unrecognizable character. If you press this button when the power is turned off, the clock is displayed. However, if you press this button when the BLUETOOTH/Network Standby mode is on, the clock is not displayed. 9 GB

10 Unit (back) CMT-SX7 CMT-SX7B SPEAKERS L/R (left/right) connectors Connect each speaker as illustrated below. connector (black) + connector (red) Connect the speaker cords while the system is turned off. Wireless LAN antenna If you use the wireless network function, set the antenna as shown in the illustration. Right speaker Left speaker 10 GB Speaker cords (supplied) LINE IN (external input) jack Connect to an output jack of the optional external components with an audio connecting cable (not supplied). AM ANTENNA (CMT-SX7 only) Connect the AM loop antenna. FM ANTENNA (CMT-SX7 only) Connect the FM antenna. DAB/FM ANTENNA (CMT-SX7B only) Connect the FM antenna. We recommend to use the optional RF cable for the DAB connection.

11 Find a location and an orientation that provide good reception, and then fix the antennas to a stable surface (window, wall, etc.). Keep the antennas away from the unit, power cord and other AV components to avoid picking noise. Secure the end of the FM lead antenna with adhesive tape. To prepare the AM loop antenna (CMT-SX7 only) 1 Fold the antenna stand as illustration. Side view LAN connector Connect network equipment with a LAN cable (not supplied) (page 26). AC power cord Inserting the batteries Insert two supplied R03 (size AAA) batteries, side first, matching the polarities shown below. Getting started Fold both parts of the stand. 2 Attach the projecting part of the frame to the antenna stand. Press until it clicks. OPTICAL IN (optical input) jack Connect to an output jack of the optional external components with an optical cable (not supplied). The system is not compatible with a format other than PCM. Set the output format of the external component to PCM. (USB REAR) port Connect a computer or Mac using a USB cable (not supplied). If you connect a WALKMAN or Xperia which is compatible with High-Resolution Audio, use a USB cable and an optional cable for WALKMAN or Xperia* (not supplied) (page 19). You can also use this as a USB-DAC. * Optional High-Resolution Audio USB Adaptor WM-PORT Cable can be ordered from your nearest Sony dealer. To connect Xperia, use a commercially available cable. With normal use, the batteries should last for about 6 months. Do not mix an old battery with a new one or mix different types of batteries. If you do not use the remote for a long period of time, remove the batteries to avoid damage from battery leakage and corrosion. 11 GB

12 About SongPal What you can do with SongPal SongPal is an application for controlling Sony audio devices which are compatible with SongPal using your smartphone/ iphone. Search for SongPal on Google Play or the App Store, and download it. The overview of the devices on the home network is displayed. You can select the audio device to play or group the audio devices using SongPal Link (multiroom function). Downloading this application on your smartphone/iphone provides the following. Music service* You can configure the initial settings to use music services. To enjoy music services, a third party application is required. Controlling devices on your home network You can play music stored in your PC or DLNA server over your network. The following functions can be operated on the system, but also by using SongPal. Operating a CD: You can play a CD. Controlling a device connected via USB: You can play music in a device connected to the (USB FRONT) port. Operating the radio: You can receive the radio station. You can select sound sources for playback from the list of the selectable sound sources. Also, you can make various sound/network settings of audio device. Refer to SongPal Help for more details GB * Depending on the country and region, music services and their period of availability may differ. A separate registration is required for certain services. An update of the device may be required. The services provided by third parties may change, stop or be terminated without notice. Sony does not assume any responsibility for such situations. What you can control with SongPal varies depending on the connected device. The specification and design of the application may change without notice.

13 Playing a CD-DA/MP3 disc Listening to a CD Press FUNCTION to select CD. Press (open/close) to open the disc tray. Set a disc on the disc tray with the label side (printed side) facing up. To eject the CD Press (open/close) on the unit. Tip The system is turned on and the disc tray is opened automatically by pressing (open/ close) while the system is turned off. Do not load a CD with non-standard shapes (e.g., heart, square, star). Doing this may cause irreparable damage to the system. Do not use a CD with tape, stickers or paste on it as this may cause malfunction. When you remove a disc, do not touch the surface of the disc. To change the play mode Play mode enables you to playback the same music repeatedly or shuffle-play. Play mode Listening to a CD Label side (printed side) 1 Press to stop playback. If you select Repeat in step 4, you do not have to stop playback. (open/close) 2 Press MENU. 4 Press (open/close) to close the disc tray. 3 Press / to select CD Menu, then press ENTER. 5 Press (play/pause). Playback starts. The button of the remote or the unit enables you to fast-rewind/fastforward, select a track, file or folder (for MP3 disc), etc. 4 5 Press / to select Playmode or Repeat, then press ENTER. Press / to select the play mode, then press ENTER. Press after Reading has disappeared from the display window. 13 GB

14 You can select the following play modes. Playmode Play mode Normal Folder* Shuffle Folder Shuffle* Program Effect Plays a track or file. Plays all tracks in the selected folder. FLDR lights up in the display window. Plays all tracks or files in random order. SHUF lights up in the display window. Plays all tracks or files in the selected folder in random order. FLDR. SHUF lights up in the display window. Plays the programmed tracks or files. PGM lights up in the display window. For details, see Creating your own program (Program Play) (page 15). 999* folders (including the root folder) 999 files 250 files in a single folder 8 folder levels (in the tree structure of files) * This includes folders that have no MP3 or other files. The number of folders that the system can recognize may be less than actual number of folders, depending on the folder structure. Compatibility with all MP3 encoding/ writing software, CD-R/RW drive and recording media cannot be guaranteed. Incompatible MP3 discs may produce noise or interrupted audio or may not play at all. * Only during MP3 disc playback. When playing back a CD (CD-DA), this mode will operate in the same way as normal playback or shuffle playback. Repeat Play mode All (Repeat plays all tracks) One (Repeat plays one track) Off Effect The system plays all tracks in a disc or folder repeatedly. lights up in the display window. The system plays the selected track repeatedly. 1 lights up in the display window. Cancels repeat playback. 14 GB on playing MP3 discs Do not save unnecessary folders or files on a disc that has MP3 files. The system can only play MP3 files that have a file extension of.mp3. Even when file name has the.mp3 file extension, if it is not an audio MP3 file, playing this file may generate a loud noise, which could cause damage of the system. The maximum number of MP3 folders and files compatible with this system is:

15 Creating your own program (Program Play) To delete a programmed track, file or folder Press while the play is stopped. Each time you press the button, the last programmed track, file or folder will be deleted. When all the programmed tracks, files or folders are deleted, No Step appears. Plays the programmed track or file in a CD. 1 2 Select Program in step 5 of To change the play mode (page 13), then press ENTER. When using an MP3 disc, press / to select the folder containing the tracks or files that you want to program. If you want to play all tracks or files in the folder, press ENTER. Tip Up to 25 tracks, files or folders can be programmed. If you attempt to program more than 25 tracks, files or folders, Step Full! will be displayed. In this case, delete unnecessary tracks. To play the same program again, press. When the disc is ejected or the power cord is disconnected after programming, all the programmed tracks, files and folders are deleted. Listening to a CD 3 Press / to select a desired track or file, then select ENTER. Selected track or file number Total playing time of the selected track or file Repeat the steps above to program additional tracks or files. 4 Press. Your program of tracks or files starts playback. To cancel program play In step 1, select Normal for Program, then press ENTER. 15 GB

16 Listening to the radio Tuning in a radio station 2 Press / to select Tuner Menu, then press ENTER. 3 Press / to select FM Mode, then press ENTER. 4 Press / to select Mono, then press ENTER. To receive stereo broadcast, select Stereo following step Press FUNCTION to select TUNER FM or TUNER AM (CMT-SX7), or DAB or TUNER FM (CMT- SX7B). Press and hold / until the frequency indication in the display window starts changing, then release the button. Tuning stops automatically when a radio station is tuned in (Automatic Scanning), and STEREO (when a FM stereo broadcast is received) appears in the display. To change the AM tuning interval (CMT-SX7 only) The default setting for AM tuning interval is 9 khz (or 10 khz for some areas). Use the buttons on the unit to perform this operation. 1 Press FUNCTION on the unit repeatedly to select TUNER AM. 2 Press / to turn off the system. 3 Press and hold MENU and press / on the unit. Step 9k or Step 10k appears in the display. When you change the interval, all the AM preset stations are erased. Manual tuning Press / repeatedly to tune-in the desired station. on DAB/DAB+ stations (CMT-SX7B only) When you tune in a station that provides RDS services, information such as the service name or station name is provided by broadcasts. When tuning in a DAB/DAB+ station, it may take a few seconds before you hear any sound. Primary service is automatically received when secondary service ends. This tuner does not support data services. If reception of an FM stereo broadcast is noisy Select monaural reception by following steps. This reduces noise. 1 Tune in the desired station, then press MENU. 16 GB

17 Presetting radio stations You can preset your desired radio stations. 1 Tune in the desired station, then press MENU. Tip You can preset up to 20 FM and 10 AM stations (CMT-SX7), or 20 DAB/DAB+ and 20 FM stations (CMT-SX7B). If you select an already-registered preset number in step 5, the preset radio station is replaced by the currently tuned-in radio station. To tune in to a preset radio station Press / to select the preset number to which the desired station is registered. 2 3 Press / to select Tuner Menu, then press ENTER. To preset an AM station, select AM Preset Memory and follow step 4 (CMT-SX7 only). Press / to select FM Preset Memory (for FM stations) or DAB Preset Memory (for DAB stations (CMT-SX7B only)), then press ENTER. Before you can tune in DAB/DAB+ stations, you must perform a DAB Initial Scan. When you have moved to another area, also perform the DAB Initial Scan manually to update the DAB/DAB+ service information. 1 Running the DAB Automatic Scan manually (CMT-SX7B only) Press MENU. Listening to the radio 4 Press / to select Ok, then press ENTER. 2 Press / to select Tuner Menu, then press ENTER. 5 Press / to select preset number, then press ENTER. 3 Press / to select Initial Scan, then press ENTER. 6 Preset number Complete! appears in the display window and the radio station is registered with the preset number. Repeat the steps above to register further radio stations. Press / to turn off the power, then press / again to turn on the power. 4 Press / to select Ok, then press ENTER. Scanning begins. The scanning progress is indicated by asterisks (*******). Depending on the DAB/DAB+ services available in your area, scanning may take a few minutes. If your country or region does not support DAB/ DAB+ broadcast, No Service appears. This procedure clears all previously stored presets. Before unplugging the DAB/FM lead antenna, make sure the system is turned off to preserve your own DAB/DAB+ settings. 17 GB

18 Playing a file on a USB device You can play audio files stored on a USB device such as WALKMAN or digital media player, on this system by connecting a USB device to the system. The (USB REAR) port on the rear of the unit can be connected with a computer, WALKMAN or Xperia which is compatible with High-Resolution Audio. For details on compatible USB devices, see Compatible devices and versions (page 45). If you play back High-Resolution Audio, use the device which is compatible with USB2.0 High Speed cable. 1 2 Listening to a file on a USB device Connecting a USB device to the USB port on the front of the unit Press FUNCTION to select USB FRONT. Connect a USB device to the (USB FRONT) port on the front of the unit. When connecting the USB device, connect it directly, or via the USB cable supplied with the USB device. Wait until Reading disappears and ROOT appears. 3 Press. Starts playback. Operate with the button of the remote or unit. You can select a track, file or folder by pressing ENTER, while ROOT is appearing. Tip When playing the USB device, the play mode can be selected. Press MENU, then select USB Menu. Select Playmode or Repeat. For details, see To change the play mode (page 13). When a file on a USB device is playing, a track or file in the folder, shuffle-playback or programmed playback cannot be played. Charging begins automatically when you connect the USB device to the (USB FRONT) port of the unit. If the USB device cannot be charged, disconnect and reconnect it. For details on the charging status of the USB device, see the operating manual of the USB device. The playback order for the system may differ from the playback order of the connected digital music player. Be sure to turn off the system before removing the USB device. Removing the USB device while the system is turned on may corrupt the data on the USB device. When USB cable connection is necessary, connect the USB cable supplied with the USB device to be connected. For details on connection, refer to the operation manual supplied with the USB device to be connected. It may take time before Reading appears after connecting, depending on the type of USB device connected. Do not connect the USB device through a USB hub. When the USB device is connected, the system reads all the files on the USB device. If there are many folders or files on the USB device, it may take a long time to finish reading the USB device. With some connected USB devices, it may take a long time to transmit signals from the system or to finish reading the USB device. Compatibility with all encoding/writing software cannot be guaranteed. If audio files on the USB device were originally encoded with incompatible software, those files may produce noise or may malfunction. The system does not necessarily support all the functions provided in a connected USB device. Charging to a USB device stops under a high temperature environment. 18 GB

19 To listen to High-Resolution Audio from your computer, install the dedicated driver* 2 to your computer. * 2 For Mac OS, a driver is not required. 1 Connecting a USB device to the USB port on the rear of the unit Download the driver from the website below; For customers in Europe: For customers in other countries/ regions: If you connect a WALKMAN or Xperia to this port, use a USB cable (not supplied) and an optional cable for WALKMAN or Xperia* 3 (not supplied). If you play back High-Resolution Audio by connecting your computer, Hi-Res Audio Player (for Windows/Mac OS) is recommended. The player can be downloaded for free; For customers in Europe: For customers in other countries/regions: The USB device cannot be charged from the (USB REAR) port. * 3 Optional High-Resolution Audio USB Adaptor WM-PORT Cable can be ordered from your nearest Sony dealer. To connect Xperia, use a commercially available cable Install the driver. Follow the procedure on the website. Press FUNCTION to select USB REAR. Connect a computer, WALKMAN or Xperia which is compatible with High-Resolution Audio, etc., to the (USB REAR) port on the rear of the unit. Operate playback by the computer, WALKMAN or Xperia which is compatible with High-Resolution Audio. For details, see the operating instructions of your computer, WALKMAN or Xperia. Playable audio formats For details about playable audio formats, see Section for USB port (page 48). Listening to a file on a USB device 19 GB

20 Listening to music of an iphone/ipad/ ipod Playing via USB connection You can play an iphone/ipad/ipod by connecting it to the (USB FRONT) port in the front of the unit. For details on compatible iphone/ipad/ipod, see Compatible devices and versions (page 45). To use an iphone/ipad/ipod, refer to the user s guide of your iphone/ipad/ipod. Sony cannot accept responsibility in the event that data recorded to iphone/ipad/ipod is lost or damaged when using an iphone/ipad/ipod with this system. Playing via wireless connection (AirPlay) You can play back via a wireless connection. For details, see the Wi-Fi Startup Guide (separate document) Press FUNCTION to select USB FRONT. Connect an iphone/ipad/ipod to (USB FRONT) port on the front of the unit using the cable supplied with the iphone/ipad/ ipod. The display changes to ipod. Press. Starts playback. You can fast-rewind/fast-forward the track or select the track using buttons on the remote or the unit. Tip Charging begins automatically when you connect an iphone/ipad/ipod to the system. If an iphone/ipad/ipod cannot be charged, disconnect and reconnect it. For details on the charging status of an iphone/ipad/ipod, see the operating manual of an iphone/ipad/ipod. Before disconnecting the iphone/ipad/ipod, turn off the system. If you disconnect it when the system is on, the data stored on the iphone/ ipad/ipod may be corrupted. Do not carry the system with an iphone/ipad/ ipod connected to the system. Doing so may cause a malfunction. 20 GB

21 Listening to music with connected components Playing back the music of connected components You can listen to a track of connected components through external output connected to the unit. Beforehand, press to turn down the volume. The system may enter Standby mode automatically if the volume level of the connected component is too low. For details, see Setting the Automatic Standby function (page 30). 1 2 Playing a component connected to the OPTICAL IN jack Press FUNCTION to select OPTICAL IN. Connect an optical cable to the OPTICAL IN (external input) jack on the rear of the unit and the output terminal of the optional external equipment. 4 Press +/ to adjust the volume. The OPTICAL IN jack is not compatible with a format other than PCM. Set the output format of the connected component to PCM Playing a component connected to the LINE IN jack Press FUNCTION to select LINE IN. Connect its audio connecting cord to the LINE IN (external input) jack on the rear of the unit and the output terminal of the optional external equipment. Start playback of the connected component. Adjust the volume on the connected component during playback. Press +/ to adjust the volume. Listening to music with connected components 3 Start playback of the connected component. Adjust the volume on the connected component during playback. 21 GB

22 Listening to music through a BLUETOOTH connection Pairing the system with a BLUETOOTH device and listening to music You can listen to music from BLUETOOTH device over a wireless connection. Before using the BLUETOOTH function, perform pairing to register your BLUETOOTH device. Place the BLUETOOTH device to be connected within one meter of the system. If your BLUETOOTH device is compliant with touch (NFC), skip the next procedure. See Listening to music by one-touch action (NFC) (page 24) Press FUNCTION to select BLUETOOTH. Press MENU. Press / to select Bluetooth Menu, then press ENTER. Press / to select Pairing, then press ENTER. Press / to select Ok, then press ENTER. When Pairing starts flashing in the display window, the system changes to pairing mode Search for this system with the BLUETOOTH device. A list of the devices found may appear on the BLUETOOTH device display. Select [CMT-SX7/CMT-SX7B] (this system). If prompted to enter a passkey on the BLUETOOTH device, enter If this system is not shown in the display window of the device, proceed from step 1 again. When pairing is completed, the display changes to the connected BLUETOOTH from Pairing and the device name is displayed. Start playback and adjust the volume on the BLUETOOTH device. Starts playback. Depending on the BLUETOOTH device, press again. Also, you may have to start up a music player on the BLUETOOTH device. Tip You can perform a pairing operation or attempt to make a BLUETOOTH connection with another BLUETOOTH device while the BLUETOOTH connection is established with one BLUETOOTH device. The currently established BLUETOOTH connection is canceled when BLUETOOTH connection with another device is successfully established. Operation such as fast-rewind/fast-forward, selecting music and selecting a folder can be operated with the remote or buttons of the unit. Stop the playback of the BLUETOOTH device while performing pairing. If you perform pairing while playing, sound may be output with very loud volume from the system after connecting. SongPal does not have a music playback function via the BLUETOOTH connection. Play music using the music playback software of BLUETOOTH devices (such as smartphone, PC, etc.). The operations described above may not be available for certain BLUETOOTH devices. In addition, the actual operations may differ 22 GB

23 depending on the connected BLUETOOTH device. Once a pairing operation is performed, it does not have to be performed again. In the following cases, however, a pairing operation must be performed again: Pairing information was erased when the BLUETOOTH device was repaired. You attempt to pair the system with more than 9 BLUETOOTH devices. This system can pair with up to 9 BLUETOOTH devices. If you pair another BLUETOOTH device after pairing with 9 devices was performed, pairing information of the device that was connected with the system first is overwritten with that of the new device. Pairing registration information of this system is erased from the connected device. If you initialize the system or erase the pairing history with the system, all the pairing information will be erased. The sound of this system cannot be sent to a BLUETOOTH speaker. Passkey may be called Passcode, PIN code, PIN number or Password, etc. If you have erased the pairing information, you cannot make a BLUETOOTH connection unless pairing is performed again. Listening to music through a registered device After step 1 on Pairing the system with a BLUETOOTH device and listening to music, operate the BLUETOOTH device to connect with the system, then start playback and adjust the volume on the BLUETOOTH device. Tip Stop playback on the BLUETOOTH device before connecting the system to the BLUETOOTH device. To check the address of a connected BLUETOOTH device Press DISPLAY while the name set on the connected BLUETOOTH device is shown in the display window. The BLUETOOTH device address appears in the display window for about 8 seconds. To cancel the connection with the BLUETOOTH device Disconnect the BLUETOOTH connection on the BLUETOOTH device. BLUETOOTH appears in the display window. Depending on the device, the connection may be canceled automatically when you stop playback. To erase the pairing registration information 1 Select Delete Link after step 3 on Pairing the system with a BLUETOOTH device and listening to music (page 22), then press ENTER. 2 Press / to select Ok, then press ENTER. Complete! appears in the display window and all the pairing information is erased. Listening to music through a BLUETOOTH connection 23 GB

24 Listening to music by one-touch action (NFC) NFC is a technology for short-range wireless communication between various devices such as a mobile phone and IC tag. Just touch your smartphone/tablet on the system. The system is turned on automatically, and pairing and BLUETOOTH connection are established. Beforehand, turn the NFC settings to on. 1 Touch your smartphone/tablet on the N-Mark on the unit. Touch the smartphone/tablet on the unit and maintain contact until the smartphone/tablet responds. Refer to the user s guide of your smartphone/tablet for the part of your smartphone/tablet used as touch contact. Stop the playback of the BLUETOOTH device when touching a smartphone/tablet. If you touch while playing, sound may be output with very loud volume from the system after connecting. When you touch an NFC-compliant smartphone/ tablet on the unit while another BLUETOOTH device is connected with this system, the BLUETOOTH device is disconnected and the system is connected with the smartphone/ tablet. In some countries and regions, NFC-compliant application may not be downloaded. 2 After completing the connection, start playback on the smartphone/tablet. To disconnect the established connection, touch your smartphone/ tablet on the N-Mark on the unit. 24 GB Tip Compatible smartphones are those equipped with the NFC function (compatible operating system: Android version or later with the exception of Android 3.x). Check the website below for information on compatible devices. For customers in Europe: For customers in other countries/regions: If the smartphone/tablet does not respond even though it is touched to the unit, download NFC Easy Connect to your smartphone/tablet and run it. Then touch to the unit again. NFC Easy Connect is a free application for exclusive use with Android. Scan the following 2D Code.

25 Playing with high quality sound codec (AAC/LDAC) You can receive the data in AAC or LDAC codec format from a BLUETOOTH device. It provides the playback with a higher quality sound. The factory settings of Bluetooth Codec is Auto. 1 Press MENU. LDAC is an audio coding technology developed by Sony that enables the transmission of High- Resolution (Hi-Res) Audio content, even over a BLUETOOTH connection. Unlike other BLUETOOTH compatible coding technologies such as SBC, it operates without any downconversion of the Hi-Res Audio content* 1, and allows approximately three times more data* 2 than those other technologies to be transmitted over a BLUETOOTH wireless network with unprecedented sound quality, by means of efficient coding and optimized packetization. * 1 excluding DSD format contents * 2 in comparison with SBC (Subband Coding) when the bitrate of 990kbps (96/48kHz) or 909kbps (88.2/44.1kHz) is selected 2 3 Press / to select Bluetooth Menu, then press ENTER. Press / to select Bluetooth Codec, then press ENTER. 4 Press / to select Auto or SBC, then press ENTER. Auto: Select when receiving with the LDAC, AAC, or SBC codec. SBC: Select when receiving with the SBC codec. If you initiate setup during BLUETOOTH connection, the connection is cut. If sound is interrupted during reception, set to SBC in step 4. Listening to music through a BLUETOOTH connection 25 GB

26 Listening to music via a Wi-Fi network Selecting the method of network connection If you connect this system to a network, you can enjoy this system in various ways. Depending on your network environment, setting up methods are different. Select the appropriate connecting method for your network environment from below. Tip For setting the fixed IP address, use the screen in step 6 of Connecting with a computer (page 26). Connecting to a Wi-Fi network and a wired network simultaneously is not possible. When you connect to a Wi-Fi network, be sure to disconnect the LAN cable from the unit. Depending on the function, the system may need to be updated. Method for using a smartphone/ iphone Install the SongPal application for your smartphone/iphone. For details, refer to the Wi-Fi Startup Guide (separate document). Connecting with a computer If your wireless router does not have a WPS (AOSS) button, configure Wi-Fi settings by connecting the unit to your computer with a LAN cable. Prepare a commercially-available LAN cable beforehand. Tip When setting up a Wi-Fi network, the SSID (Wi-Fi Network Name) and security key (WEP or WPA key) may be required. The security key (or network key) uses encryption to limit the devices with which communication can occur. It is used to provide higher security for devices communicating via a wireless router/access point. 1 Record the SSID and password of your router. For details, refer to the operating instructions of your router. SSID (Wi-Fi Network Name) Password (Security Key) Method for using a wireless router with a WPS (AOSS) button Use the WPS button to connect. For details, refer to the Wi-Fi Startup Guide (separate document). Method for using computer See Connecting with a computer (page 26). Method for using wired network Refer to Help Guide for details. 2 Connect the unit to the computer with a LAN cable directly. LAN cable (not supplied) 26 GB

27 3 Press / to turn on the system. Wait until starts flashing in the display window. It takes about 2 minutes (in some cases, 4 or 5 minutes). 6 Select the SSID of your wireless router and enter the password. 4 Access the [Sony Network Device Settings] screen. For PC Start the browser and input either of the following URLs into the browser s address bar. 7 See the recorded password in step 1 (page 26). Select [Apply]. SSID 5 The above URL is only for when the PC and unit are connected with a LAN cable. For Mac Start Safari and select [Bonjour] under ([Bookmarks]), then select [CMT- SX7/CMT-SX7B]. Select [Network Settings] from the menu. 8 When prompted, unplug the LAN cable from the unit. When the LAN cable is unplugged from the unit, in the display window turns off. When the Wi-Fi connection is established, lights up in the display window. It may take more than 2 minutes to light up. For information on how to listen to music with this system, refer to the Wi-Fi Startup Guide (separate document). This procedure needs to be completed within 10 minutes. If you cannot complete, reset the system (page 42). Listening to music via a Wi-Fi network Network Settings 27 GB

28 Listening to the same music from the multiple speakers (SongPal Link function) Listening to an Internet music service (Google Cast) The following instructions explain how to use a Google Cast-enabled music app. Enjoy music in any room via Wi-Fi. You can listen to your favorite music stored in your PCs or mobile phones and furthermore, music from streaming services, in different rooms with ultimate sound quality. 1 2 Install the free application SongPal on your smartphone/ iphone. Connect the system and smartphone/iphone to your Wi- Fi network. Connect the system and smartphone/ iphone to the same SSID (network) of your router Install the free application SongPal on your smartphone/iphone. Connect the system and smartphone/ iphone to your Wi-Fi network. Connect the system and smartphone/iphone to the same SSID (network) of your router. Launch SongPal, and download a Google Cast-enabled music app. Launch SongPal, then tap [CMT-SX7/ CMT-SX7B] [Settings] [Google Cast] [Learn how to cast]. See the instructions, then find and install a Google Cast-enabled app on your smartphone/iphone. Launch the Google Cast-enabled app, then tap the Cast button to select [CMT-SX7/CMT-SX7B]. 3 When connecting multiple devices, connect the multi-room compatible devices to your Wi-Fi network. Refer to Help Guide for detailed operation. 5 Select music to listen to on your Google Cast-enabled app. The music is played on the system. Refer to Help Guide for detailed operation GB

29 Listening to an Internet music service (Spotify) Depending on the country and region, music services and their periods of availability may differ. Spotify gives you instant access to millions of songs. The Spotify Connect feature lets you select music on the Spotify App and stream it on the system. To use Spotify Connect feature, you need a Premium account. For details, visit Connect the system and smartphone/iphone to your Wi- Fi network. Connect the system and smartphone/ iphone to the same SSID (network) of your router. Download the Spotify App to your smartphone/iphone from Google Play or the App Store Launch the Spotify App and log in to a Spotify Premium account. Select and start playing the music. Tap the Connect icon ( ) and select the system as the audio output device. Listening to music via a Wi-Fi network Select the system Tip When Spotify Connect is activated, the Connect icon ( ) lights up. 29 GB

30 30 GB Additional information Setting the Automatic Standby function The system enters Standby mode automatically in about 15 minutes when there is no operation or audio signal output (Automatic Standby function). By default, the Automatic Standby function is turned on Press MENU. Press / to select Standby Mode Menu, then press ENTER. Press / to select Auto Standby, then press ENTER. Press / to select On or Off, then press ENTER. Tip 2 minutes before entering Standby mode, Auto Standby displays in the display window. The Automatic Standby function is invalid for the tuner function, even when you have enabled it. The system may not enter Standby mode automatically in the following cases: while using the tuner function while the Play Timer or Sleep Timer is being used The system counts down the time (about 15 minutes) again until it enters Standby mode, even when Automatic Standby function is enabled in the following cases: when a USB device is connected in USB function when a button on the remote or unit is pressed when NFC-touch is performed Setting the BLUETOOTH/Network Standby mode When BLUETOOTH/Network Standby mode is enabled, the system enters Wait mode for BLUETOOTH or network connection even when the system is turned off. This mode is disabled by default Press MENU. Press / to select Standby Mode Menu, then press ENTER. Press / to select BT/NW Standby, then press ENTER. Press / to select On or Off, then press ENTER. Press / to turn off the system. Tip When this function is set to On and you connect to the system from a BLUETOOTH, AirPlay, or DLNA device, or make the Music Services connection, the system turns on automatically and you can listen to music by using the BLUETOOTH, AirPlay, DLNA, or Music Service connection. When the system is connected to a network, this function may be set to On automatically. To comply with the power saving regulation in Europe, products with the serial number or later cannot use this function when the product is connected to the wired network or not connected to the wireless network. This function will not be available when the network connection is disconnected as well. If so, set this function again. When the multi-room function turns on, it supports TDLS (Tunneled Direct Link Setup) and works as a wireless router that improves the data communication quality (Version 1.60 or later).

31 Setting the wireless signal ON/OFF When the unit is turned on, you can control a wireless network or BLUETOOTH signal. The default setting is on Turn on the unit. If flashes in the display window, press and hold BACK and of the unit. After RF Off (wireless signal is off) or RF On (wireless signal is on) appears, release the button. Tip When this setting is set to off, the wireless network function and BLUETOOTH function are not available. When this setting is off, the unit is turned on by the smartphone/tablet by one-touch action (NFC) on the unit. When this setting is off, the BLUETOOTH/ Network Standby mode cannot be set. When this setting is set to off while the BLUETOOTH/Network Standby mode is on, the BLUETOOTH/Network Standby mode turns off. When this setting is off, the unit and BLUETOOTH device cannot be paired. Even when this setting is off, a wired connection can still be used. Adjusting the sound Adjusts the sound to your preference. Selecting DSEE HX produces better quality sound of a compressed file, such as MP Press MENU. Press / to select Sound Menu, then press ENTER. Press / to select BASS, TREBLE, or DSEE HX, then press ENTER. BASS: Adjusts the bass sound. TREBLE: Adjusts the treble sound. DSEE HX: Upgrades the sound quality better than CD or MP3. Complements the treble of a compressed file, such as MP3, and upgrades to a higher level of sampling frequency and number of bits from its original numeric. Select to Auto. (The default setting is Auto. ) To use the Clear Audio+ function The Clear Audio+ function activates and sound is set to Sony s recommended settings by pressing CLEARAUDIO+. Additional information 31 GB

32 Setting the clock Using the timers Press / to turn on the system. Press MENU. Press / to select Timer Menu, then press ENTER. If Play Setting is displayed, press / to select Clock Setting, then press ENTER. Press / to set the hour, then press ENTER. The system offers Sleep Timer and Play Timer. The Sleep Timer has priority over the Play Timer. At the specified time, the system is turned off automatically. 1 2 Setting the Sleep Timer Press MENU. Press / to select Sleep Menu, then press ENTER. 5 Press / to set the minutes, then press ENTER. Complete the clock setting. The clock settings are reset when you disconnect the power cord or if a power failure occurs. To display the clock when the system is off Press DISPLAY to display the clock. The clock is displayed for about 8 seconds. If the BLUETOOTH/Network Standby mode is on, the clock does not appear by pressing DISPLAY. 3 Press / to select the specified time, then press ENTER. You can select from 10minutes (10 minutes) to 90minutes (90 minutes) in 10-minute increments. Tip To check the remaining time of Sleep Timer, perform steps 1 and 2 above. The Sleep Timer works even if the clock is not set. To cancel the Sleep Timer Select Off in step 3 above. Setting the Play Timer Make sure you have set the clock before setting the timer (page 32). 32 GB Play Timer You can listen to a CD, USB device or radio every day at a preset time. The Play Timer setting remains as long as the setting is not canceled.

33 Prepare the sound source. Press MENU. Press / to select Timer Menu, then press ENTER. Press / to select Play Setting, then press ENTER. The start time flashes in the display window. Press / to select time, then press ENTER. Follow the same procedure to set Minute of the time to start operation, then Hour and Minute of the time to stop the operation. Press / to select the desired sound source, then press ENTER. The confirmation display for the Play Timer appears. and you change the radio frequency or band after setting the timer, the radio station setting for the timer will also be changed. When the sound source for a Play Timer is set to a radio station tuned from a preset radio station, and you change the frequency of the radio station or band after setting the timer, the radio station setting for the timer will not change. The radio station tuning for the timer is fixed at the frequency you set. To check the setting 1 Press MENU. 2 Press / to select Timer Menu, then press ENTER. 3 Press / to select Timer Select, and then press ENTER. 4 Press / to select Play Setting, and then press ENTER. The timer setting appears in the display window. To cancel the timer After step 3 on To check the setting (page 33), select Timer Off, then press ENTER. 7 Press / to turn off the system. Tip When the sound source is a CD, you can preprogram the Play Timer. See Creating your own program (Program Play) (page 15). When the sound source is radio, make sure to tune-in the radio station in advance (page 16). To change the timer setting, perform the procedures from the beginning again. The Play Timer does not work if the system is already on at the preset time. Turn off the unit about 5 minutes before the preset time. Be careful not to operate the system until it is turned on and starts play with the timer. When the sound source for a Play Timer is set to a radio station that you set using Automatic Scanning (AUTO) or Manual Tuning (MANUAL), Additional information 33 GB

34 Updating the software You can update your system s pre-installed software by using one of the following 3 methods. Method 1: Automatic update via the Internet (page 34) When the system is connected to the Internet, it can detect a new software version and automatically update. This feature requires system settings to be made by using a smartphone/iphone installed with SongPal (page 12). Method 2: Manual update via the Internet (page 35) When the system is connected to the Internet, it can detect a new software version and if found, UPDATE appears in the display window to inform you. This is the default setting. Method 3: Manual update via a USB flash drive (page 35) When the system is not connected to the Internet, use a computer or another device to download the update file, then install it to the system. Usually it may take about 3 to 10 minutes for the system to finish the update. More time may be needed, depending on the network environment. Do not operate the unit or the remote during updating. Moreover, do not disconnect the power cord and network during updating. The update procedure via Internet can be terminated by performing MENU button > Download Cancel > Ok while Download is displayed (depending on the update progress status, canceling cannot be executed). If the update procedure has been terminated, Cancel! and Push POWER will appear alternately. When you turn on the system next time after termination, UPDATE will appear in the display window if the system detects a new software version again. 1 Method 1: Automatic update via the Internet Launch SongPal on your smartphone/iphone, and set [Time Zone] in the [Settings] menu. The automatic software update feature ([Auto Update]) of the system is activated. The update is performed when you are not using the system, such as during midnight or when the system is in standby mode. The standby indicator lights up during the update, and Complete appears in the display window when the update is complete. Tip To deactivate the software automatic update, disable [Auto Update] in the [Settings] menu by using SongPal. However, the software may still be updated automatically for critical changes, even if you disable this function. When the system is connected to the Internet via a wired or Wi-Fi network, UPDATE appears in the display window when the system detects a new software version. Regardless of the [Auto Update] setting, UPDATE will appear when the system detects a new software version. You can update the software manually even when the [Auto Update] setting is activated. See Method 2: Manual update via the Internet (page 35). If Cannot Download and Push POWER appear alternately The automatic software update has failed. See When the update via a network has failed (page 36). 34 GB

35 Method 2: Manual update via the Internet Method 3: Manual update via a USB flash drive When UPDATE appears, follow the steps below. 1 2 Press MENU. Press / to select Update Menu, then press ENTER. 1 2 Download the update file from the website below, then store it in a USB flash drive. For customers in Europe: For customers in other countries/ regions: Turn on the system if needed. 3 Press / to select via Network, then press ENTER. 3 Press FUNCTION to select USB FRONT. 4 5 Press / to select Ok, then press ENTER. Download and Update appear continuously, then the standby indicator will light up in orange when updating starts. Do not operate the system or the remote during updating. When Complete appears, press / to turn off the power, then press / again to turn on. If Cannot Download and Push POWER appear alternately The software update has failed. See When the update via a network has failed (page 36) Connect the USB flash drive prepared in Step 1 to the (USB FRONT) port on the front of the unit. When ROOT appears in the display window, press MENU. Press / to select Update Menu, then press ENTER. Press / to select via USB, then press ENTER. Additional information 8 Press / to select Ok, then press ENTER. Download and Update appear continuously, then the standby indicator will light up in orange when updating starts. Do not operate the system or the remote during updating. 35 GB

36 9 When Complete appears, press / to turn off the power, then press / again to turn on. When the update via a network has failed If the network connection is not reliable, the update may fail before it completes. When Cannot Download and Push POWER appear alternately, the software update has failed. In this condition, the system will not respond to any operation and no functions can be used, except the / button operation. Follow the steps below to examine the system s condition, then complete the update with an appropriate method. flash drive. For customers in Europe: For customers in other countries/ regions: While Update Retry is displayed, connect the USB flash drive to the (USB FRONT) port on the front of the unit. Download and Update appear continuously, then the standby indicator will light up in orange when updating starts. Do not operate the system or the remote during updating. When Complete appears, press / to turn off the power, then press / again to turn on. 1 2 Press / to turn off the power, then press / again to turn on. Wait about 3 minutes (or until a network connection is established), then check the display window. When UPDATE is displayed The update is not complete, though the system can be used normally. Follow the steps below. Turn off the system. Perform the procedures in Method 3: Manual update via a USB flash drive (page 35). When Update Retry is displayed 36 GB The update has failed and the system cannot be used. Proceed to the next step to update using a USB flash drive. Download the update file from the website below, then store it in a USB

37 Troubleshooting Troubleshooting If a problem occurs while operating the system, follow the steps described below before consulting your nearest Sony dealer. If an error message appears, be sure to make a note of the contents for reference. 1 Check to see if the problem is listed in this Troubleshooting section. 2 Check the following customer support websites. For customers in Europe: For customers in other countries/ regions: You will find the latest support information and a FAQ at these websites. 3 If, after steps 1 and 2, you still cannot solve the problem, consult your nearest Sony dealer. If the problem persists after doing all of the above, consult your nearest Sony dealer. When bringing the product in for repairs, be sure to bring in the entire system (main unit and remote). This product is a system product, and the entire system is needed to determine the section requiring repair. If the standby indicator flashes in red Immediately unplug the power cord and make sure the speaker cord is not hot. Is the speaker cord shorted out? After the standby indicator stops flashing, plug the power cord again, and turn on the system. If the issue persists, contact your nearest Sony dealer. Depending on the function, the system may need to be updated. General The system does not turn on. Make sure you have connected the power cord to a wall outlet correctly. The system has entered Standby mode unexpectedly. This is not a malfunction. The system enters Standby mode automatically in about 15 minutes when there is no operation or audio signal output. See Setting the Automatic Standby function (page 30). The clock setting or the Play Timer operation has been canceled unexpectedly. If about a minute elapses with no operation, the clock setting or Play Timer setting is canceled automatically. Perform the operation again from the beginning. There is no sound. Make sure the speaker cords are connected correctly. Turn up the volume on the unit. Make sure the headphones are disconnected from the jack. Make sure the component is connected correctly to the LINE IN (external input) jack and set the function to LINE IN. The specified station may have temporarily stopped broadcast. Left and right sound balance is unclear or reversed. Put the speakers symmetrically. Make sure that speaker cords L/R and +/ are connected correctly. Severe hum or noise occurs. Move the system away from sources of noise. Connect the system to a different wall outlet. Use of an AC power tap with a noise filter (not supplied) is recommended. The remote does not function. Remove any obstacles between the remote and the remote sensor on the unit, and position the unit away from fluorescent lights. Point the remote at the remote sensor on the unit. 37 GB Troubleshooting

38 38 GB Move the remote closer to the system. Replace the new batteries. CD-DA/MP3 disc Locked appears in the display window and the disc cannot be removed from the disc tray. Consult your nearest Sony dealer or local authorized Sony service facility. The disc or file will not play. The disc has not been finalized (a CD-R or CD- RW disc to which data can be added). The sound skips, or the disc will not play. The disc may be dirty or scratched. When the disc is dirty, wipe it clean. Move the system to a location away from vibration (for example, on top of a stable stand). Oscillation of the speakers may be the cause of sound skips, depending on the volume level. Move the speakers away from the unit or change the location of the speakers. A DTS disc is played. Do not play the DTS disc. Play does not start from the first track or file. Make sure the current play mode is correct. If the play mode is Shuffle or Program, change the setting (page 13). Starting playback takes more time than usual. The following discs can increase the time it takes to start playback: a disc recorded with a complicated tree structure a disc recorded in multi-session format a disc that has many folders BLUETOOTH Unable to pair the unit with a BLUETOOTH device/bluetooth connection between the system and smartphone/iphone is not possible using SongPal. Bring the unit and the BLUETOOTH device to within 1 m (3 ft) of each other. If you initialize the system, the system may not be able to connect your iphone/ipad/ipod or computer. In this case, erase the pairing information on the iphone/ipad/ipod or computer, and then perform the pairing procedure again. Unable to connect the system to a BLUETOOTH device with one-touch connection (NFC). Keep the smartphone/tablet close to the unit until the smartphone/tablet responds. If the system fails to connect, move the smartphone/tablet slowly on the N-Mark of the unit. When the smartphone/tablet responds, follow the on-screen instructions to establish the connection. Check that the NFC function of the smartphone/tablet is set to on. If the smartphone/tablet is in a case, remove it. NFC reception sensitivity varies, depending on the device. If you repeatedly fail to connect the unit with a smartphone/tablet by one touch, make the connection by on-screen operation. Check that your smartphone/tablet is compatible with NFC. Check the websites below for details on the latest supported versions of the compatible devices: For customers in Europe: For customers in other countries/regions: There is no sound. Check that the system has established BLUETOOTH connection with the BLUETOOTH device. Pair the system and the BLUETOOTH device again. Distorted sound/humming or noise in the speaker output. Bring the unit and the BLUETOOTH device closer together. Remove any obstacles between the unit and the BLUETOOTH device. Set Bluetooth Codec to SBC (page 25). iphone/ipad/ipod (when connected to USB port) For details on compatible iphone/ipad/ipod, see Compatible devices and versions (page 45).

39 There is no sound. Make sure the iphone/ipad/ipod is connected securely to the (USB FRONT) port. Stop playback and connect the iphone/ipad/ ipod to the system. Make sure the iphone/ipad/ipod is updated with the latest software. If not, update the iphone/ipad/ipod before using with the system. Turn up the volume. The iphone/ipad/ipod may not be supported by this system. The sound is distorted. Make sure the iphone/ipad/ipod is connected securely to the (USB FRONT) port. Turn up the volume. Set the equalizer setting of the iphone/ipad/ ipod to Off or Flat. The iphone/ipad/ipod may not be supported by this system. The iphone/ipad/ipod does not function. Shut down any other ios applications running on the iphone/ipad/ipod. For details, refer to the operation manual supplied with the iphone/ipad/ipod. Make sure the iphone/ipad/ipod is connected securely to the (USB FRONT) port. Make sure the iphone/ipad/ipod is updated with the latest software. If not, update the iphone/ipad/ipod before using with the system. Because the operation of the system and the iphone/ipad/ipod are different, you may not be able to operate the iphone/ipad/ipod using buttons on the remote or unit. In this case, use the control buttons on the iphone/ ipad/ipod. The iphone/ipad/ipod cannot be charged. Make sure the iphone/ipad/ipod is connected securely to the (USB FRONT) port via the cable supplied with the iphone/ipad/ipod. Disconnect the iphone/ipad/ipod and then reconnect it. For details on the charging status of the iphone/ipad/ipod, see the operating manual of the iphone/ipad/ipod. USB device For details on compatible USB devices, see Compatible devices and versions (page 45). An unsupported USB device is connected. The following problems may occur. The USB device is not recognized. File or folder names are not displayed on this system. Playback is not possible. The sound skips. There is noise. A distorted sound is output. There is no sound. The USB device is not connected correctly. Turn off the system, and then reconnect the USB device. There is noise, skipping, or distorted sound. An unsupported USB device is connected. Connect a supported USB device. Turn off the system, then reconnect the USB device and turn on the system. The music data itself contains noise, or the sound is distorted. Noise may have been entered when creating music data due to the conditions of the computer. In this case, delete the file and send the music data again. The bit rate used when encoding the files was low. Send files encoded with higher bit rates to the USB device. If you play back High-Resolution Audio, use the device which is compatible with USB2.0 High Speed cable. Reading is displayed for an extended time, or it takes a long time before playback starts. The reading process may take a long time in the following cases. There are many folders or files on the USB device. The file structure is extremely complex. Not enough free space in the memory. The internal memory is fragmented. The file or folder name (album name) is not displayed correctly. Send the music data to the USB device again, as the data stored in the USB device may have been corrupted. The character code that can be displayed by this system are as follows: Upper cases (A to Z). Numbers (0 to 9). Symbols (< > * +, [ \ _). Troubleshooting 39 GB

40 Other characters appear as _. The USB device is not recognized. Turn off the system and reconnect the USB device, then turn on the system. An incompatible USB device may be connected. The USB device does not work properly. Refer to the operating manual supplied with the USB device for how to deal with this problem. Play does not start. Turn off the system and reconnect the USB device, then turn on the system. An incompatible USB device may be connected. Play does not start from the first track. Set the play mode to Normal play mode. The USB device cannot be charged. Make sure the USB device is connected securely to the (USB REAR) port. Charging cannot be made when the power of the system is off. The USB device may not be supported by this system. Disconnect the USB device and then reconnect it. For details on the charging status of the USB device, see the operating manual of the USB device. Tuner Severe hum or noise occurs ( STEREO flashes in the display window), or broadcasts cannot be received. Connect the antenna properly. Find a location and an orientation that provide good reception, and then set up the antenna again. Keep the antennas away from the unit, speaker cord or other AV components to avoid picking up noise. Turn off nearby electrical equipment. Several radio stations can be heard at the same time. Find a location and orientation that provide good reception, and adjust the speaker cord, then set up the antenna again. Bundle the antenna cables using commercially available cord clips and adjust the cable lengths. DAB/DAB+ radio station is not received properly (CMT-SX7B only). Check all antenna connections, then perform the DAB Automatic Scan procedure. See Running the DAB Automatic Scan manually (page 17). The current DAB/DAB+ service may not be available. Press / to select a different service. If you have moved to another area, some services/frequencies may have changed and you may not be able to tune into your usual broadcast. Perform the DAB Automatic Scan procedure to re-register the contents of broadcasts. (Performing this procedure clears all previously stored presets.) The DAB/DAB+ broadcast has been interrupted (CMT-SX7B only). Check the location of the system or adjust the orientation of the antenna to increase the indicated value of the signal quality. Network connection The system cannot connect to the network. (Other equipment on the network cannot find or recognize the system.) Check that is lit in the display window. It takes about 2 minutes for the system to acquire an IP address when the system is turned on in a communication environment without a router. When you use a fixed IP address, the same IP address may be used by other equipment. Use a different IP address. The system cannot connect to the network via a wireless LAN connection. If a network (LAN) cable is connected to the system, the system automatically operates to establish a wired LAN connection. If you wish to use a wireless LAN connection, do not connect a network (LAN) cable to the system. Check the settings of the wireless LAN router/ access point. If the SSID stealth mode is set to On on the access point, set it to Off. For details on the settings of the access point of the wireless router, refer to the operating manual for the access point. 40 GB

41 The system cannot connect to the network using WPS. Set up your network after searching the access point using the access point scan. You cannot connect to a network using WPS when your access point is set to WEP. Update the firmware of the wireless LAN router/access point to the latest version. Music Services Wireless signal condition is poor. Stop using your microwave oven. The communications speed of the wireless LAN may become slower for IEEE802.11ncompliant wireless LAN routers/access points if the security method is set to WEP or WPA/ WPA2-PSK (TKIP). If the speed becomes lower, change the security method to WPA/WPA2- PSK (AES). The encryption (security) scheme varies depending on the device. For details, refer to the operating manual for your router/access point. The system cannot connect to Music Services. Make sure the wireless LAN router/access point is turned on. Check that appears in the display window. If not, set up a wireless network again. For details, see Wi-Fi Startup Guide. When the system is connected to a wireless network, place the wireless LAN/access point and the system closer together and perform the setup again. Depending on the providers, only one connection to Internet is allowed. In that case, the system cannot be connected if connection is occupied. Please consult your carrier or service provider. When you turn on your mobile phone (Android device, Xperia device, or iphone/ipod touch) after a moment of power off, try to restart the SongPal application. Home Network The controller (the operating device) cannot find this system. (The controller cannot browse the contents of this system.) Make sure that the controller is connected to the home network. The multicast control on the access point is enabled. Music started automatically. This system may be controlled by another component. To reject the control, set the BLUETOOTH/Network Standby mode to off (page 30). The sound is interrupted. The DLNA server is overloaded. Quit all running applications. Tuning or playback cannot be performed. Confirm that the audio file is improper or has been deleted from the server. Refer to the operating manual of the server. The server tries to play the audio file in an audio format that the system does not support. Check the audio format information on the server. Disable the multicast control on the wireless LAN router/access point. If it is enabled, it may take several minutes to output the audio. For details, refer to the operating manual of the wireless LAN router/access point. The access from this system is not permitted by the server. Change the settings on the server to allow access from this system. For details, refer to the operating manual of the server. AirPlay For details on compatible iphone/ipad/ipod touch, see Compatible devices and versions (page 45). The system cannot be found from an iphone/ipad/ipod touch. See Network connection The system cannot connect to the network (page 40). Make sure the iphone/ipad/ipod touch or the computer with itunes is connected to your home network. Before using with the system, update ios or itunes to the latest version. Music started automatically. This system may be controlled by another component. To reject the control, set the BLUETOOTH/Network Standby mode to off (page 30). Troubleshooting 41 GB

42 The sound is interrupted during playback. The server is overloaded. Quit all running applications. This unit cannot be operated. Update the software version of the iphone/ ipad/ipod touch or itunes to the latest version. To reset the system to factory settings If the system still does not operate properly, reset the system to factory settings. Use buttons on the unit to reset the system to its factory default settings. 1 Disconnect the power cord and confirm that the standby indicator is not lit. Then reconnect the power cord and turn on the system. 2 Press and hold PUSH ENTER and / on the unit until All Reset appears in the display window. All user-configured settings, such as the preset radio stations, clock, timer, and network, are deleted. Also, your login ID and password of the Internet music streaming (Music Services) will be deleted. If the problem persists after doing all of the above, consult your nearest Sony dealer. If you dispose of the unit or give it to another person, reset the unit for security. Messages The following messages may appear or flash during operation. Cannot Download The system failed downloading the update data while performing the software update. See When the update via a network has failed (page 36) to complete the update with an appropriate method. Cannot Play You have set a disc that cannot be played back on this system, such as CD- ROM and DVD disc. Complete! The station preset operation ended normally. Data Error You tried to play an unplayable file. Error You operated the system during initialization. Wait for a while until the initialization is completed. Initial The system is initializing the network settings. Some buttons of the system cannot be operated during this process. Locked The disc tray is locked and you cannot remove the disc. Contact your nearest Sony dealer. No Connect The system cannot be connected to the network. No Device No USB device is connected or the connected USB device has been removed. No Disc There is no disc in the player, or you have loaded a disc that cannot be played. 42 GB

43 No Memory The memory media is not inserted in the USB device, or the system does not identify the memory media. No Step All of the programmed tracks have been erased. Not Supported The system does not support the connected USB device. No Track There are not playable files on the USB device or disc. Not In Use You pressed an unplayable button. Over Current Remove the USB device from the port and turn off the system, then turn on the system. Push STOP You attempted to change the play mode during playback in the CD or USB function. Reading The system is reading the information on the CD or USB device. Some buttons do not work during reading. Step Full! You tried to program more than 25 tracks or files. Time NG! The Play Timer start and end times are set to the same time. Update Error The system cannot update the software. See When the update via a network has failed (page 36) to complete the update by using a USB flash drive. If the update via USB flash drive fails, or same message appears again, contact your nearest Sony dealer. Troubleshooting 43 GB

44 Precautions/Specifications Precautions Discs that this system CAN play Audio CD-DA discs CD-R/CD-RW (audio data of CD-DA tracks and MP3 files) Do not use a CD-R/CD-RW disc with no data stored. Doing so may damage the disc. Discs that this system CANNOT play CD-ROM CD-R/CD-RW other than those recorded in music CD format or format conforming to ISO9660 Level 1/Level 2, Joliet CD-R/CD-RW recorded in multi-session format and not closed the session CD-R/CD-RW of poor recording quality, CD-R/CD-RW that have scratches or are dirty, or CD-R/CD-RW recorded with an incompatible recording device CD-R/CD-RW which is finalized incorrectly CD-R/CD-RW containing files other than MPEG 1 Audio Layer-3 (MP3) files Discs of non-standard shape (for example, heart, square, star) Discs that have adhesive tape, paper, or sticker attached to them Rental or used discs with attached seals where the glue extends beyond the seal Discs that have labels printed using ink that feels tacky when touched on CD-DA discs Before playing, wipe the disc with a cleaning cloth from the center out to the edge. Do not clean discs with solvents, such as benzine, thinner, or commercially available cleaners or antistatic spray intended for vinyl LPs. Do not expose discs to direct sunlight or heat sources such as hot air ducts, nor leave it in a car parked in direct sunlight. it is not going to be used for an extended period of time. When unplugging the system, always grip the plug. Never pull the cord itself. Should any solid object or liquid get into the system, unplug the system, and have it checked by qualified personnel before operating it again. The AC power cord can be changed only by a qualified service facility. On placement Do not place the system in an inclined position or in locations that are extremely hot, cold, dusty, dirty, or humid or lacking adequate ventilation, or subject to vibration, direct sunlight or a bright light. Be careful when placing the system on surfaces that have been specially treated (for example, with wax, oil, polish) as staining or discoloration of the surface may result. If the system is brought directly from a cold to a warm location or is placed in a very damp room, moisture may condense on the lens inside the CD player, and cause the system to malfunction. In this situation, remove the disc, and leave the system turned on for about an hour until the moisture evaporates. If the system still does not operate, even after an extended period, consult your nearest Sony dealer. On heat buildup Heat buildup on the unit during charging or operation over a long period of time is normal and not cause for alarm. Do not touch the cabinet if it has been used continuously at a high volume because the cabinet may have become hot. Do not obstruct the ventilation holes. Cleaning the cabinet Clean this system with a soft cloth slightly moistened with a mild detergent solution. Do not use any type of abrasive pads, scouring powder, or solvents, such as thinner, benzine, or alcohol. 44 GB On safety Completely disconnect the power cord (mains lead) from the wall outlet (mains) if

45 Disclaimer regarding services offered by third parties Services offered by third parties may be changed, suspended, or terminated without prior notice. Sony does not bear any responsibility in these sorts of situations. Compatible devices and versions iphone/ipad/ipod or itunes Check the websites below for details on the latest supported versions of the compatible devices: For customers in Europe: For customers in other countries/regions: Compatible Models iphone 6 Plus AirPlay BLUETOOTH USB iphone 6 iphone 5s iphone 5c iphone 5 iphone 4s iphone 4 iphone 3GS ipad Air 2* ipad mini 3* ipad Air* ipad mini 2* ipad (4th generation)* ipad mini* ipad (3rd generation)* ipad 2* ipad* ipod touch (5th generation) Precautions/Specifications 45 GB

46 Compatible Models ipod touch (4th generation) ipod touch (3rd generation)* ipod classic* ipod nano (7th generation)* ipod nano (6th generation)* ipod nano (5th generation)* ipod nano (4th generation)* AirPlay BLUETOOTH USB USB device Check the websites below for details on the latest supported versions of the compatible devices: For customers in Europe: For customers in other countries/regions: BLUETOOTH device Check the websites below for details on the latest supported versions of the compatible devices: For customers in Europe: For customers in other countries/regions: * SongPal does not support ipod touch (3rd generation), ipod classic, and ipod nano. SongPal does not support the display optimized for ipad as of January AirPlay works with iphone, ipad, and ipod touch with ios or later, Mac with OS X Mountain Lion, and Mac and PC with itunes or later. Bluetooth technology works with iphone 5s, iphone 5c, iphone 5, iphone 4s, iphone 4, iphone 3GS, ipod touch (5th generation), ipod touch (4th generation). USB function works with iphone, ipad, and ipod touch with ios or later, Mac with OS X Mountain Lion, and Mac and PC with itunes or later. 46 GB DLNA device Check the websites below for details on the latest supported versions of the compatible devices: For customers in Europe: For customers in other countries/regions:

47 BLUETOOTH wireless technology BLUETOOTH wireless technology is a shortrange wireless technology linking digital devices, such as personal computers and digital still cameras. Using the BLUETOOTH wireless technology, you can operate the units involved within a range of about 10 meters. The BLUETOOTH wireless technology is commonly used between two devices, but a single device can be connected to multiple devices. You do not need wires to get connected as you do with a USB connection, and you do not need to place the devices face to face as you do with wireless infrared technology. You can use the technology with one BLUETOOTH device in your bag or pocket. BLUETOOTH wireless technology is a global standard supported by thousands of companies. These companies produce products that meet the global standard. Supported BLUETOOTH version and profiles Profile refers to a standard set of capabilities for various BLUETOOTH product capabilities. See Specifications (page 48) for details on the supported BLUETOOTH version and profiles. To use a BLUETOOTH device connected to this system, the device must support the same profile as this system. that the functions of the BLUETOOTH device may be different depending on the specifications of the device, even if it has the same profile as this system. Because of the properties of BLUETOOTH wireless technology, playback on this system is slightly delayed compared with audio playback on the transmitting device. Effective communication range BLUETOOTH devices should be used within approximately 10 meters (unobstructed distance) of each other. The effective communication range may become shorter under the following conditions. When a person, metal object, wall or other obstruction is between the devices with a BLUETOOTH connection Locations where a wireless LAN is installed Around microwave ovens that are in use Locations where other electromagnetic waves occur Effects of other devices BLUETOOTH devices and wireless LAN (IEEE802.11b/g/n) use the same frequency band (2.4 GHz). When using your BLUETOOTH device near a device with wireless LAN capability, electromagnetic interference may occur. This could result in lower data transfer rates, noise, or inability to connect. If this happens, try the following remedies: Try connecting this system and BLUETOOTH mobile phone or BLUETOOTH device when you are at least 10 meters away from the wireless LAN equipment. Turn off the power to the wireless LAN equipment when using your BLUETOOTH device within 10 meters. Effects on other devices The radio waves broadcast by this system may interfere with the operation of some medical devices. Since this interference may result in malfunction, always turn off the power on this system, BLUETOOTH mobile phone and BLUETOOTH device in the following locations: In hospitals, on trains, and in airplanes Near automatic doors or fire alarms This system supports security functions that comply with the BLUETOOTH specification as a means of ensuring security during communication using BLUETOOTH technology. However, this security may be insufficient depending on the setting contents and other factors, so always be careful when performing communication using BLUETOOTH technology. Sony cannot be held liable in any way for damages or other loss resulting from information leaks during communication using BLUETOOTH technology. BLUETOOTH communication is not necessarily guaranteed with all BLUETOOTH devices that have the same profile as this system. Precautions/Specifications 47 GB

48 BLUETOOTH devices connected with this system must comply with the BLUETOOTH specification prescribed by the BLUETOOTH SIG, Inc., and must be certified to comply. However, even when a device complies with the BLUETOOTH specification, there may be cases where the characteristics or specifications of the BLUETOOTH device make it impossible to connect, or may result in different control methods, display or operation. Noise may occur or the audio may cut off depending on the BLUETOOTH device connected with this system, the communications environment, or surrounding conditions. Specifications Amplifier section Power output (rated): 30 watts + 30 watts (at 6 ohms, 1 khz, 1% THD) RMS power output (reference): 50 watts + 50 watts (per channel at 6 ohms, 1kHz) Inputs/Outputs LINE IN (external input) jack: Sensitivity: 2 V Impedance: 47 kilo ohms OPTICAL IN (optical digital input) jack (headphone) jack: Stereo mini jack, 8 ohms or more Section for USB port (USB FRONT) port You can connect a USB flash drive, Walkman, or iphone/ipad/ipod that is compatible with this system. Supported format* 1 MP3: 32/44.1/48 khz, kbps (CBR/ VBR) AAC* 2 : 32/44.1/48/88.2/96 khz, kbps (CBR/VBR) WMA* 2 : 32/44.1/48 khz, kbps (CBR/ VBR) WAV: 32/44.1/48/88.2/96/176.4/192 khz (16/24 bit) AIFF: 32/44.1/48/88.2/96/176.4/192 khz (16/ 24 bit) FLAC: 32/44.1/48/88.2/96/176.4/192 khz (16/24 bit) ALAC: 32/44.1/48/88.2/96/176.4/192 khz (16/24 bit) DSD* 3 (DSF/DSDIFF): 2.8 MHz (1bit) Transfer speed High-speed Supported USB device Mass Storage Class (MSC) Maximum output current 2.1 A MAX 48 GB

49 (USB REAR) port You can connect a compatible device such as a PC, etc., to this unit using a USB cable (not supplied). Supported format* 1 PCM: 44.1/48/88.2/96/176.4/192 khz (16/ 24/32 bit) DSD (DSF/DSDIFF): 2.8 MHz (1 bit) * 1 Compatibility with all encoding/writing software, recording devices and recording media cannot be guaranteed. * 2 Files with DRM (Digital Rights Management) copyright protection or files downloaded from an online music store cannot be played on this system. If you try to play one of these files, the system plays the next unprotected audio file. * 3 Output by converting to PCM. CD-DA/MP3 player section System: Compact disc and digital audio system Laser Diode Properties: Emission Duration: Continuous Laser Output* 1 : Less than 44.6 μw * 1 This output is the value measurement at a distance of 200mm from the objective lens surface on the Optical Pick-up Block with 7mm aperture. Other models: 530 khz 1,710 khz (with 10 khz tuning interval) 531 khz 1,710 khz (with 9 khz tuning interval) Intermediate frequency: 400 khz FM tuner section: FM stereo, FM superheterodyne tuner Tuning range: 87.5 MHz MHz (50 khz step) DAB/DAB+ tuner section (CMT-SX7B only): FM stereo, DAB/FM superheterodyne tuner Frequency range: Band-III: (5A) MHz (13F) MHz* 1 DAB/DAB+ frequency table (Band-III): Frequency MHz 5A MHz 5B MHz 5C MHz 5D MHz 6A Label Frequency response: 20 Hz 20 khz Signal-to-noise ratio: More than 90 db Dynamic range: More than 90 db Tuner section AM tuner section (CMT-SX7 only): Tuning range: European models: 531 khz 1,602 khz (with 9 khz tuning interval) Asian models: 530 khz 1,610 khz (with 10 khz tuning interval) 531 khz 1,602 khz (with 9 khz tuning interval) MHz 6B MHz 6C MHz 6D MHz 7A MHz 7B MHz 7C MHz 7D MHz 8A MHz 8B MHz 8C MHz 8D MHz 9A Precautions/Specifications MHz 9B 49 GB

50 50 GB Frequency MHz 9C MHz 9D * 1 Frequencies are displayed to two decimal places on this system. Speaker section Speaker system: 2-way speaker system, Bass Reflex Woofer: 100 mm, cone type Tweeter: 27 mm, Balanced soft dome type Rated impedance: 6 ohms Label MHz 10A MHz 10B MHz 10C MHz 10D MHz 11A MHz 11B MHz 11C MHz 11D MHz 12A MHz 12B MHz 12C MHz 12D MHz 13A MHz 13B MHz 13C MHz 13D MHz 13E MHz 13F Dimensions (W/H/D): Approx. 145 mm x 245 mm x 225 mm Mass: Approx. 3.5 kg (per unit) BLUETOOTH section Communication system: BLUETOOTH Standard version 3.0 Output: BLUETOOTH Standard Power Class 2 Maximum communication range: Line of sight approx. 10 m *1 Frequency band: 2.4 GHz band ( GHz GHz) Modulation method: FHSS Compatible BLUETOOTH profiles *2 : A2DP (Advanced Audio Distribution Profile) AVRCP (Audio Video Remote Control Profile) Supported content protection method SCMS-T method Supported codec SBC (Sub Band Codec), AAC, LDAC Transmission bandwidth 20 Hz 20,000 Hz (with 44.1 khz sampling) * 1 The actual range will vary depending on factors such as obstacles between devices, magnetic fields around a microwave oven, static electricity, reception sensitivity, antenna s performance, operating system, software application, etc. * 2 BLUETOOTH standard profiles indicate the purpose of BLUETOOTH communication between devices. Network section LAN port: RJ-45 10BASE-T/100BASE-TX (The communication speed may vary depending on the communication environment. This system does not guarantee the communication speed and quality of 10BASE-T/100BASE-TX.) Wireless LAN: Compatible standards: IEEE a/b/g/n (WEP 64 bit, WEP 128 bit) Frequency band 2.4/5 GHz band

51 WEP 64 bit, WEP 128 bit WPA/WPA2-PSK (AES) WPA/WPA2-PSK (TKIP) Compatible formats: PCM 192 khz/24 bit, DSD 2.8 MHz/1 bit DSD (DSF, DSDIFF), LPCM (WAV, AIFF), FLAC, ALAC, MP3, AAC, WMA General Power requirements: Latin America models (except for Argentina models): AC 120 V V, 50 Hz/60 Hz Other models: AC 220 V V, 50 Hz/60 Hz Power consumption: 46 watts Dimensions (W/H/D) (incl. projecting parts, without speakers): Approx. 225 mm x 115 mm x 263 mm Mass (without speakers): Approx. 2.7 kg Supplied accessories: Remote (RMT-AM100U) (1), R03 (Size AAA) batteries (2), FM lead antenna (1), AM loop antenna (1) (CMT-SX7 only), Speaker cords (2), Adaptor (1) (Latin America models only), Wi-Fi Startup Guide (1), Operating Instructions (this manual) (1) Design and specifications are subject to change without notice. Standby power consumption: 0.5 W (all wireless network ports off) Networked Standby mode: 6 W (all wireless network ports on) * When the multi-room function turns on, it supports TDLS (Tunneled Direct Link Setup) and works as a wireless router that improves the data communication quality (Version 1.60 or later). Precautions/Specifications 51 GB

52 Trademarks, etc. Windows, the Windows logo, and Windows Media are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. This product is protected by certain intellectual property rights of Microsoft Corporation. Use or distribution of such technology outside of this product is prohibited without a license from Microsoft or an authorized Microsoft subsidiary. Apple, the Apple logo, AirPlay, ipad, iphone, ipod, ipod classic, ipod nano, ipod touch, itunes, Mac and OS X are trademarks of Apple Inc., registered in the U.S. and other countries. ipad Air and ipad mini are trademarks of Apple Inc. App Store is a service mark of Apple Inc. Made for ipod, Made for iphone, and Made for ipad mean that an electronic accessory has been designed to connect specifically to ipod, iphone or ipad, respectively, and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards. Please note that the use of this accessory with ipod, iphone or ipad may affect wireless performance. Wi-Fi, Wi-Fi Protected Access and Wi-Fi Alliance are registered marks of the Wi-Fi Alliance. Wi-Fi CERTIFIED, WPA, WPA2 and Wi-Fi Protected Setup are marks of the Wi-Fi Alliance. is a mark of the Wi-Fi Alliance. DLNA, the DLNA Logo and DLNA CERTIFIED are trademarks, service marks, or certification marks of the Digital Living Network Alliance. WALKMAN and WALKMAN logo are registered trademarks of Sony Corporation. MPEG Layer-3 audio coding technology and patents licensed from Fraunhofer IIS and Thomson. The BLUETOOTH word mark and logos are registered trademarks owned by BLUETOOTH SIG, Inc. and any use of such marks by Sony Corporation is under license. The N-Mark is a trademark or registered trademark of NFC Forum, Inc. in the United States and in other countries. Android and Google Play are trademarks of Google Inc. Google Cast and the Google Cast Badge are trademarks of Google Inc. Xperia and Xperia Tablet are trademarks of Sony Mobile Communications AB. LDAC and LDAC logo are trademarks of Sony Corporation. DSEE and are trademarks of Sony Corporation. S-Master is a trademark of Sony Corporation. ClearAudio+ and are trademarks of Sony Corporation. AOSS is a trademark of BUFFALO INC. 52 GB This product incorporates Spotify software which is subject to 3rd party licenses found here: Spotify and Spotify logos are trademarks of the Spotify Group. The system names and product names indicated in this manual are generally the trademarks or registered trademarks of the manufacturer. and marks are omitted in this manual.

53

54

55

56 2015 Sony Corporation Printed in China (1)