Written By: Cassandra Beck

Size: px

Start display at page:

Download "Written By: Cassandra Beck"

Elwin Long
5 years ago
Views:

1 Kindle Fire HD 6 Screen Replacement This guide details how to remove the screen from the Kindle Fire HD 6. Written By: Cassandra Beck ifixit CC BY-NC-SA Page 1 of 13

2 INTRODUCTION This guide explains how to remove the screen from the Kindle Fire HD 6. This guide has many steps, so make sure to give yourself enough time to complete all of these. Note that some of the connectors in this guide are delicate and require special removal, so make sure to read the steps completely before attempting them. TOOLS: ifixit Opening Tools (1) Spudger (1) T5 Torx Screwdriver (1) Suction Handle (1) PARTS: Kindle Fire HD 6 LCD (1) Kindle Fire 6 Digitizer (1) ifixit CC BY-NC-SA Page 2 of 13

Step 1 Back Panel Place the device face down on a clean cloth or another smooth surface.

If your device is on a rough surface, you may scratch the screen.

You might need to wiggle the tool up and down to wedge it in the gap.

3 Step 1 Back Panel Place the device face down on a clean cloth or another smooth surface. In the following steps, you will need to apply some force to your device. If your device is on a rough surface, you may scratch the screen. Insert the plastic opening tool between the device s front and back panels. You might need to wiggle the tool up and down to wedge it in the gap. Maneuver the tool around the device until the back unclips from the front panel. Step 2 Carefully separate the back panel from the rest of the device internals. ifixit CC BY-NC-SA Page 3 of 13

motherboard next to the battery connector.

4 Step 3 Speaker Unscrew the two 3.5mm T5 Torx screws at the base of the speaker. Step 4 Unclip the speaker wire that runs up the side of the battery and clips into the motherboard next to the battery connector. Gently pull it straight up. ifixit CC BY-NC-SA Page 4 of 13

5 Step 5 Lift the speaker out of the device. Step 6 Rear Facing Camera Unscrew the two 3.5mm T5 Torx Screws from the top of the camera. ifixit CC BY-NC-SA Page 5 of 13

Step 7 Be careful not to damage the camera lens as you remove the camera.

As you pull, unclip the black and white connector with orange tape by popping it off at its

Take care not to pierce or rupture the battery, which can release dangerous chemicals.

to soften the adhesive, and then slide a credit card behind the battery to break up the

6 Step 7 Be careful not to damage the camera lens as you remove the camera. Gently pull the camera up and out of the device. As you pull, unclip the black and white connector with orange tape by popping it off at its base. Step 8 Battery Gently pry the battery free from the adhesive holding it in place. Take care not to pierce or rupture the battery, which can release dangerous chemicals. If you're having trouble working the battery free, warm it up with an iopener or hair dryer to soften the adhesive, and then slide a credit card behind the battery to break up the adhesive. Be careful not to yank the battery out you'll need to disconnect a connector before removing the battery completely. ifixit CC BY-NC-SA Page 6 of 13

7 Step 9 Remove the multi-colored connector that joins the battery and the motherboard by pulling it straight up. Remove the battery. ifixit CC BY-NC-SA Page 7 of 13

Use the tip of the spudger to disconnect the two zero insertion force connectors on the bottom and top of the motherboard.

8 Step 10 Motherboard Zero insertion force connectors can break easily. Before performing this step, read the ifixit Guide to Recognizing and Disconnecting Cable Connectors to find out how to safely remove them. Use the tip of the spudger to disconnect the two zero insertion force connectors on the bottom and top of the motherboard. The first connector is attached to an orange tape, and is located in the bottom-right corner of the motherboard. Remove this connector. The second connector is long and thin, and is located at the top of the motherboard, a bit to the right of center. Remove this connector. ifixit CC BY-NC-SA Page 8 of 13

of the spudger. Step 12 Unscrew the ten 3.

9 Step 11 Disconnect the black and white connector at the very top-center of the motherboard by unclipping it using the flat side of the spudger. Step 12 Unscrew the ten 3.5mm T5 Torx screws around the edge of the motherboard. ifixit CC BY-NC-SA Page 9 of 13

Step 13 Starting from the bottom, lift the

10 Step 13 Starting from the bottom, lift the motherboard out of the device. You will have to push the motherboard about two millimeters toward the top of the device to unhook the top edge. Step 14 Screen Remove the five gold-colored 2mm T5 Torx screws from the metal plate. ifixit CC BY-NC-SA Page 10 of 13

Step 15 An orange tape that connects to the

11 Step 15 An orange tape that connects to the motherboard runs through the metal plate. When removing the plate, be careful to maneuver the plate around the tape, and make sure not to stretch or rip the tape. Lift the metal plate up using the flat side of the spudger. Step 16 Remove the metal plate from the device. ifixit CC BY-NC-SA Page 11 of 13

Step 17 Unscrew the four silver-colored 2mm T5 Torx screws that

Step 18 Be careful not to scratch the screen while you're

After you've removed the screen, place it on a cloth or another

out of the device. Push the suction cup against the screen.

12 Step 17 Unscrew the four silver-colored 2mm T5 Torx screws that connect the screen to the bezel. Step 18 Be careful not to scratch the screen while you're removing it. After you've removed the screen, place it on a cloth or another smooth surface to make sure that you don t scratch it once it is out of the device. Push the suction cup against the screen. Press down firmly on the center of the suction cup to create a good seal. Gently pull the screen out of the device. ifixit CC BY-NC-SA Page 12 of 13

13 Step 19 Place your screen on a cloth or another smooth surface to prevent it from getting scratched. To reassemble your device, follow these instructions in reverse order. This document was last generated on :17:41 PM. ifixit CC BY-NC-SA Page 13 of 13

Motorola Moto Z2 Play Audio Jack Replacement

Motorola Moto Z2 Play Audio Jack Replacement How to replace your Moto Z2 Play's audio jack with this guide if you can't hear with headphone or if there are scratching noises. Written By: mitch miller ifixit