led22115 RAWMNLeng V Änderungen sind ohne Ankündigung möglich. Changes are possible without prior notice.

Transcription

1 Tour-BAR 64 led22115 PRE-MANUAL RAWMNLeng V Änderungen sind ohne Ankündigung möglich. Changes are possible without prior notice.

2 Safety instruction? Make sure the power supply voltage are consistent with this lights,ensure the use of voltage is in the range of the request technical parameter.?before the installation, please check the light s fasteners and mechanical structure have been received in good condition and appear no damage.?this light is designed for indoor use; working temperature is lower than 40 degree.?the fixtures maybe mounted in any position provided there is adequate room for ventilation. Make sure there are no inflammable and explosive items (ornaments) in 0.5 meters away.?yellow / green cabling earthling safety; no flicker when the fixture is working on. 1. Outside Size Picture

3 2 Main Function Input voltage: AC 100V-264V/47-63HZ Consume:200W Lamp Type:15W LED 4-in-1 R G B W(16PCS) Control Signal:DMX512 Control mode:stand alone/ Master/Slaver Channel:72CH,64CH,48CH,40CH,24CH,16CH,10CH,5CH,4CH,3CH Function Effect: dimmer, strobe, gradual change, rainbow, auto run, self-program running Built-in temperature control measurement function, when LED work overheated, intelligent reduce LED output power, current power output and can be viewed. Cooling mode: Natural Convection Beam Angle: 10 x 40 Protection: IP65

4 DMX Channels 3 DMX Control Function Illustrations: The same numbers represent the same group. 72CH CHANNEL NAME CHANNEL NAME 1 DIM ALL 37 W9 2 R1 38 R10 3 G1 39 G10 4 B1 40 B10 5 W1 41 W10 6 R2 42 R11 7 G2 43 G11 8 B2 44 B11 9 W2 45 W11 10 R3 46 R12 11 G3 47 G12 12 B3 48 B12

5 14 R4 50 R13 15 G4 51 G13 16 B4 52 B13 17 W4 53 W13 18 R5 54 R14 19 G5 55 G14 20 B5 56 B14 21 W5 57 W14 22 R6 58 R15 23 G6 59 G15 24 B6 60 B15 25 W6 61 W15 26 R7 62 R16 27 G7 63 G16 28 B7 64 B16 29 W7 65 W16 30 R8 66 STROBE 31 G8 67 EFFECT 32 B8 68 AUTO SPEED 33 W8 69 VIRTUAL COLOR WHEEL 34 R9 70 DIMMER MODE 35 G9 71 ID FUNCTION 36 B9 72 ID ADDRESS 64CH CHANNEL NAME CHANNEL NAME 1 R1 33 R9 2 G1 34 G9 3 B1 35 B9 4 W1 36 W9 5 R2 37 R10 6 G2 38 G10 7 B2 39 B10 8 W2 40 W10 9 R3 41 R11 10 G3 42 G11 11 B3 43 B11 12 W3 44 W11 13 R4 45 R12 14 G4 46 G12

6 15 B4 47 B12 16 W4 48 W12 17 R5 49 R13 18 G5 50 G13 19 B5 51 B13 20 W5 52 W13 21 R6 53 R14 22 G6 54 G14 23 B6 55 B14 24 W6 56 W14 25 R7 57 R15 26 G7 58 G15 27 B7 59 B15 28 W7 60 W15 29 R8 61 R16 30 G8 62 G16 31 B8 63 B16 32 W8 64 W16 48CH NAM CHANNEL NAME CHANNEL E 1 R1 25 R9 2 G1 26 G9 3 B1 27 B9 4 R2 28 R10 5 G2 29 G10 6 B2 30 B10 7 R3 31 R11 8 G3 32 G11 9 B3 33 B11 10 R4 34 R12 11 G4 35 G12 12 B4 36 B12 13 R5 37 R13 14 G5 38 G13 15 B5 39 B13 16 R6 40 R14 17 G6 41 G14

7 18 B6 42 B14 19 R7 43 R15 20 G7 44 G15 21 B7 45 B15 22 R8 46 R16 23 G8 47 G16 24 B8 48 B16 40CH CHANNEL NAME CHANNEL NAME 1 DIM ALL 21 W5 2 R1 22 R6 3 G1 23 G6 4 B1 24 B6 5 W1 25 W6 6 R2 26 R7 7 G2 27 G7 8 B2 28 B7 9 W2 29 W7 10 R3 30 R8 11 G3 31 G8 12 B3 32 B8 13 W3 33 W8 14 R4 34 STROBE 15 G4 35 EFFECT 16 B4 36 AUTO SPEED 17 W4 37 VIRTUAL COLOR WHEEL 18 R5 38 DIMMER MODE 19 G5 39 ID FUNCTION 20 B5 40 ID ADDRESS 24CH 16CH CHANNEL NAME CHANNEL NAME 1 DIM ALL 1 DIM ALL 2 R1 2 R1

8 3 G1 3 G1 4 B1 4 B1 5 W1 5 W1 6 R2 6 R2 7 G2 7 G2 8 B2 8 B2 9 W2 9 W2 10 R3 10 STROBE 11 G3 11 EFFECT 12 B3 12 AUTO SPEED 13 W3 13 VIRTUAL COLOR WHEEL 14 R4 14 DIMMER MODE 15 G4 15 ID FUNCTION 16 B4 16 ID ADDRESS 17 W4 18 STROBE 19 EFFECT 20 AUTO SPEED VIRTUAL COLOR 21 WHEEL 22 DIMMER MODE 23 ID FUNCTION 24 ID ADDRESS 10CH 5CH 4CH CHANNEL NAME CHANNEL NAME CHANNEL NAME 1 DIM ALL 1 DIM ALL 1 R 2 R1 2 R1 2 G 3 G1 3 G1 3 B 4 B1 4 B1 4 W 5 W1 5 W1 6 STROBE 7 EFFECT 8 AUTO SPEED VIRTUAL 9 COLOR WHEEL 10 DIMMER MODE 3CH CHANNE L NAM E

9 1 R 2 G 3 B NAME VALUE FUNCTION DIM ALL DARK->LIGHT RED DARK->LIGHT GREEN DARK->LIGHT BLUE DARK->LIGHT AMBER DARK->LIGHT WHITE 0-5 DARK->LIGHT STROBE 0-5 No strobe 6-20 Not synchronous strobe(slow to fast) Synchronous strobe(slow to fast) Electronic Sine wave(slow to fast) Random Strobe(slow to fast) Opening pulse(slow to fast) Closing pulse(slow to fast) Electronic Square wave(slow to fast) EFFECT 0-5 NO EFFECT 6-10 CT01(Call custom color CT01) CT CT CT CT CT CT CT CT CT AUTO AUTO AUTO AUTO AUTO AUTO AUTO AUTO AUTO 9

10 AUTO AUTO AUTO AUTO AUTO AUTO AUTO AUTO AUTO AUTO AUTO AUTO AUTO AUTO AUTO AUTO AUTO AUTO AUTO AUTO AUTO AUTO AUTO AUTO CHASE CHASE CHASE RESERVED AUTO SPEED AUTO SPEED,FAST->SLOW VIRTUAL COLOR 0-10 No effect WHEEL (RGB color mixing instead of RGB channels but W channels not affected) 11 Blue (Blue=full, Red+Green+White=0)(step) Red=0, Green->up,Blue =full, White=0(proportional) Light Blue (Red=0, Green=full, Blue =full, White=0)(step) Red=0, Green=full, Blue->down, White=0(proportional)

11 Green (Red=0, Green=full, Blue =0, White=0)(step) Red->up, Green=full, Blue=0, White=0(proportional) Yellow (Red=full, Green=full, Blue=0, White=0)(step) Red=full, Green->down, Blue=0, White=0(proportional) Red(Red=full, Green=0, Blue=0, White=0)(step) Red=full, Green=0, Blue->up, White=0(proportional) Magenta (Red=full, Green=0, Blue=full, White=0)(step) Red -> down, Green=0, Blue=full, White=0(proportional) Blue (Red=0, Green=0, Blue=full, White=0)(step) DIMMER MODE 0-10 Use the dimmer mode which menu had set up Linear curve and not smooth Square law curve and not smooth Inverse square law curve and not smooth S-curve and not smooth Linear curve and smooth Square law curve and smooth Inverse square law curve and smooth S-curve and smooth Use the dimmer mode which menu had set up ID FUNCTION 0-10 ID DISABLE ID ENABLE RESERVED ID ADDRESS ID ADDRESS ID ADDRESS CHANNEL DIVIDED BY 10 AND ENABLE

12 AUTO Details 1 R,G,B,W,RG,RB,GB,RGBW 2 R?,R?,G?,G?,B?,B?,W?,W? 3 R?G?,R?G?,R?B?,R?B?,B?G?,B?G? 4 R?G?B?W?,R?G?B?W? 5 B,BG?,BG,B?G,G,GR?,GR,G?R,R,RB?,RB,R?B(Rainbow effect) 6 One piece running from 1 to 16 then change color continue 7 RGBY step running 8 4Y running with fade 9 4P step running 10 4R running on G 11 4G running on B 12 4Y running on P 13 4R step running 14 4C step running 15 6Y running with fade 16 6P running with fade 17 Y open from 1 to 16 then dark 18 B open from 1 to 16 then dark 19 Each piece change with RGBYPC 20 Inverse direction AUTO 6 21 Inverse direction AUTO P running with fade 23 Inverse direction AUTO 9 24 Inverse direction AUTO Inverse direction AUTO Inverse direction AUTO Inverse direction AUTO Inverse direction AUTO R running with fade 30 4B running with fade 31 Inverse direction AUTO Inverse direction AUTO 18

13 33 Each piece rainbow effect 4 Display Operation instruction MENU : access the menu or return to a previous menu option ENTER: select the current menu option UP: menu selection or parameter increments DOWN: menu selection or parameters decrease Menu Tree: TAB LEVEL1 LEVEL2 LEVEL3 LEVEL4 ADDR(Address) STAT(Static control) R * G * B * W * R * G * B * W * SHUT * SET(Set) CAL(Calibration) R 0-255

14 CHMD(Channel mode) G B W USE YES/NO 72CH 64CH 48CH 40CH 24CH 16CH 10CH 5CH 4CH 3CH CTST(Custom color set) DIM(Dimming mode) DISY(Display set) LOCK(Key 2 minutes lock) LIN(linear)/SQR(square law)/isqr(inverse square law)/scur(s-curve)/lin.(linear smooth)/sqr.(square law smooth)/isqr.(inverse square law smooth)/scur.(s-curve smooth) ON(Permanent on) 2MIN (2 minutes off) YES/NO CT01 R G B W CT10 AUTO(Auto) AT01 RUN.. *. RUN.. *. RUN.. *. RUN.. * AT33 RUN.. * ATSP(Auto speed) CHS1(Chase 1) RUN.. * CHS1(Chase 2) RUN.. * CHS1(Chase 3) RUN.. * PROG(Program) CHS1(Chase 1) SC01(Scene 1) R G B

15 .. W R G B W SHUT AUTO NONE,AT0 1-AT33.. ATSP 0-255(S).. TIME 0-255(S).. WAIT (S).. USE YES/NO. SC20(Scene 20) CHS3(Chase 3) INFO(Information) SOFT(Software version) Vx.x TEM(Temperature) xxxc POW(Power reduction) xxx% LOAD(Load) ST L(Setting load) YES/NO PR L(Program load) YES/NO SEND(Send) YES/NO ID(ID Address) Illustrations: When enter to the * position displayed on the LED, the projector will automatically set as master and send datas to external. Other projectors will synchronously running without manually set as slaver. When power cycle it will jump to the * position and running again. And in these position it will not return back to the default display after two minutes. 5 DMX ADDRESS SETTING 1) Press the ENTER button in ADDR menu, then enter to the DMX address setting. 2) Press the UP/DOWN button to select numerical value. 3) Press the ENTER button to escape and save. 6 STATIC SETTING 1) Press the ENTER button in STAT menu, then enter to the static setting. 2) Press the UP/DOWN button to select RED1, GREEN1, BLUE1, WHITE1 SHUT.

16 3) Press the UP/DOWN button to set up the numerical value. 4) Press the ENTER button to escape and save. 7 COLOR CAST CALIBRATION SETTING 1) Press the ENTER button in CAL menu, then enter to the color cast calibration setting. 2) Press the UP/DOWN button to select RED, GREEN, BLUE, WHITE 3) Press the UP/DOWN button to set up the numerical value. 4) On the USE interface, pressing YES button means valid, NO means invalid. 5) Press the ENTER button to escape and save. Illustrations: When pressing the YES button which means valid on the USE interface, the actual output value of RED,GREEN,BLUE,WHITE is output in accordance with the percentage which the color cast calibration value divides CHANNEL MODE SETTING 1) Press the ENTER button in CHMD menu, then enter to the channel mode setting. 2) Press the UP/DOWN button to select 72CH, 64CH, 48CH, 40CH, 24CH., 16CH, 10CH., 5CH, 4CH, 3CH 3) Press the ENTER button to escape and save. 9 DIMMING MODE SETTING 1) Press the ENTER button in DIM menu, then enter to the dimming mode setting. 2) Press the UP/DOWN button to select LIN, SQR, ISQR, SCUR, LIN., SQR., ISQR. and SCUR.. 3) Press the ENTER button to escape and save. Illustrations:When setting LIN., SQR., ISQR. and SCUR. in DIM menu, there will be added a little delay dimming effect for smooth.. Dimming curve: Linear curve: square law curve: Inverse Square law curve: S-curve:

17 10 DISPLAY SETTING 1) Press the ENTER button in DISY menu, then enter to the display setting. 2) Press the UP/DOWN button to select ON, 2 MINITES OFF 3) Press the ENTER button to escape and save. 11 AUTO LOCK KEY SETTING 1) Press the ENTER button in LOCK menu, then enter auto lock key setting. 2) Press the UP/DOWN button to select YES, NO 3) Press the ENTER button to escape and save. Instructions: When set to [YES], it will lock automatically after two minutes to prevent accidental triggering flood flushing. And then press any key for 10 seconds to unlock. 12 CUSTOM COLOR SETTING 1) Press the ENTER button in CTST menu, then enter to the custom color setting. 2) Press the UP/DOWN select CT01 CT10 2) Press the UP/DOWN button to select numerical value. 3) Press the ENTER button to escape and save. 13 AUTO RUN, SELF-PROGRAM RUN 1)Press the ENTER button in AUTO menu, then enter to the auto run,self-program run. 2)Press the UP/DOWN button to select AT01 AT33, SPEED, CHASE01 CHASE03 3)Press the ENTER button to start running. 14 EDIT SELF-PROGRAM 1) Press the ENTER button in PROG menu, then enter to the edit self-program.

18 2) Press the UP/DOWN button to select CHASE01 CHASE03 3) Press the ENTER button for confirmation and enter to the next menu. 4) Press the UP/DOWN button to select SCENE01 SCENE20 5) Press the ENTER button for confirmation and enter to the next menu. 6) Then press the UP/DOWN button to select RED1 SHUT, TIME, WAIT, USE 7) Press the UP/DOWN button to set up the parameter which are needed. 8) Press the ENTER button t o escape and save. Illustrations:When USE is set to be NO,or the parameter of TIME is 0, it will not run this scene.when WAIT is set to be FADE time, the running process isas the following chart showing. 15 CHECK THE LIGHTING INFORMATION 1) Press the ENTER button in INFO menu, then enter to the checking the lighting information. 2) SOFT button is for software version information. 3) TEMP Current temperature of lamp board. 4) POW button is for the current information of power reduction. 16 LIGHTING SETTING PARAMETER RESET 1) Press the ENTER button in ST L menu, then enter to the lighting setting parameter reset. 2) Press the UP/DOWN button to select YES. 3) Press the ENTER button to escape and save. Illustrations: ADDR CTST and PROG are not reset, the others reset to the underlined value of the word. 17 PROG SELF-PROGRAMMING PARAMETER RESET 1) Press the ENTER button in PR L menu, then enter to the PROG self-programming parameter reset. 2) Press the UP/DOWN button to select YES. 3) Press the ENTER button to escape and save. 18 LIGHTING PARAMETER DOWNLOADING EACH OTHER VIA DMX

19 CABLE 1) Press the ENTER button in SEND menu, then enter to sending parameter to other lightings. 2) Press the UP/DOWN button to select YES. 3) Press the ENTER button to confirm sending. Illustrations: 1)Please disconnect the connection of projector and DMX console before sending the parameter. 2)The information of ADDR CAL ID can t be sent, can t be downloaded each other. 3)There will be an automatic reset of the other projectors after receiving parameter correctly. 19 ID ADDRESS SETTING 1) Press the ENTER button in ID menu, then enter to the ID address setting. 2) Press the UP/DOWN button to select numerical value. 3) Press the ENTER button to escape and save. Illustrations: 1)When ID FUNCTION in channel profile is 10-20,the ID ADDRESS in fixture setting must equal to the ID ADDRESS in channel profile setting then the fixture will be actived. 2)When ID FUNCTION in channel profile is 21-30,the ID ADDRESS in channel profile setting will be divided by 10 then ignore the fractional part, if the result is equal to the ID ADDRESS which setted in ID menu,the fixture will be actived.for example, if the fixture ID ADDRESS is 3 now,the valid value in the channel profile setting is Similarly when 15 the valid value is