RRC-1258 MkII(s) and RRC-1258MkIIs Yaesu Twin

Size: px
Start display at page:

Download "RRC-1258 MkII(s) and RRC-1258MkIIs Yaesu Twin"

Transcription

1 RRC-5 MkII(s) nd RRC-5MkIIs Yesu Twin User Mnul B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 of 9

2 Tble of contents Sttement of Conditions... Generl Description... 7 Detchble control pnel... 7 PC-bsed control... Step by step system setup... 9 Hrdwre... Front... Bck... 5 Strpping nd jumpers... 9 Configurtion with Microbit Setup Mnger... 3 FW/HW version... 4 FW updte... 4 Setup... Net info... 7 Initil IP setup... Configurtion with WEB-interfce... 3 Info... 3 Sttus Profiles IP Settings Rdio Settings Seril Settings... 4 Advnced settings... 5 Dynmic DNS setting (only Rdio-RRC) Keyer Settings (Control-RRC) Keyer Settings (Rdio-RRC) IO Settings... 0 Ping settings (only Rdio-RRC)... 4 Export settings (HTML)... 5 Export settings (bin)... 5 Import settings (bin)... Appliction firmwre upgrde... 7 Bootloder firmwre upgrde... Restrt device... Configurtion with terminl-interfce... 9 CW-Keyer Generl Settings Connections... 7 RTTY Keying B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 of 9

3 Generl RTTY with MMTTY Settings Connections... 7 ICOM CI-V Generl Hrdwre configurtion Rdio settings (exmple)... 0 Connections... 0 ICOM IC-703, IC Generl... 4 Hrdwre configurtion... 4 Rdio settings (exmple)... 5 Connections... 5 Power supply... Prepre the seprtion cble to IC-703 nd IC ICOM IC-R Generl... 9 Hrdwre configurtion... 9 Rdio settings (exmple)... 9 Connections Power supply ICOM IC-E Generl... 9 Hrdwre configurtion... 9 Rdio settings (exmple)... 9 Connections Using HM-33 Microphone Power supply ICOM ID-E Generl Hrdwre configurtion Rdio settings (exmple) Connections HM-33/0 Microphone dpter bords Modifictions of the Control-RRC circuit bord... 0 Modifictions of the Rdio-RRC circuit bord Power supply... 0 ICOM IC Generl... Hrdwre configurtion... Rdio settings (exmple)... 4 Connections... 4 Power supply... 4 YAESU FT-x7, FT B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 3 of 9

4 Generl... 7 Hrdwre configurtion... 7 Rdio settings (exmple)... Connections... YAESU Generl (FT-000)... 3 Generl... 3 Hrdwre configurtion... 3 Rdio settings (exmple)... 4 Connections... 4 YAESU TWIN... Generl... Hrdwre configurtion... 9 Rdio settings (exmple)... 3 Connections... 3 Logging or computer control, RTTY etc KENWOOD Generl Generl Hrdwre configurtion Rdio settings (exmple)... 4 Connections... 4 KENWOOD TS Generl... 4 Hrdwre configurtion... 4 Rdio settings (exmple) Connections Power supply... 4 KENWOOD TM-D Generl... 5 Hrdwre configurtion... 5 Rdio settings (exmple)... 5 Power supply... 5 KENWOOD TS Generl Hrdwre configurtion Rdio settings (exmple)... 5 Connections... 5 ELECRAFT K3-Twin... 0 Hrdwre configurtion... 0 Rdio settings (exmple)... Connections... Connections... Logging or computer control, RTTY etc ELECRAFT Generl B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 4 of 9

5 Hrdwre configurtion Rdio settings (exmple) Connections... 7 ALINCO DX-SR nd DX-R Generl Hrdwre configurtion... 7 Rdio settings (exmple)... 7 Connections... 7 Power supply RRC-5MkII with -wire or 4-wire interfces... 7 Generl... 7 Hrdwre configurtion... 7 Rdio settings (exmple) Connections Power supply Schemtics I/O nd PAD interfce... MIC/AUX Interfce Control-RRC MkII... Speker output interfce Control-RRC MkIIs... 3 Speker input interfce Rdio-RRC MkIIs... 3 MIC/AUX Interfce Rdio-RRC... 4 Networks nd Firewlls... 5 DMZ... Portforwrding... 7 SIP ALG... Mobile Network Routers... 9 Appendix B - COM-port Keyer interfce... 9 Appendix D - Technicl Dt... 9 Appendix E - Sfety nd Regultory Informtion FCC Sttement Sfety Notice Disclimer FCC / CE - Declrtion of conformity B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 5 of 9

6 Sttement of Conditions In the interest of improving internl design, opertionl function, nd/or relibility, Microbit.0 AB reserves the right to mke chnges to the product described in this document without notice. Microbit does not ssume ny libility tht my occur due to the use or ppliction of the product(s) or circuit lyout(s) described herein. All prts of the softwre re property of Microbit.0 AB. The hrdwre design, schemtics PCB lyout, concept, grphics, user mnul, etc. re property of Microbit.0 AB. The device my not be disssembled, copied or reversed engineered. Copyright 00,0 Microbit.0 AB All rights reserved. B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 of 9

7 Generl Description The Remoterig RRC-5MkII (RRC) is developed especilly for remote control of Amteur rdio sttions vi the Internet in user-friendly nd cost-effective wy. The RRC units re used in pirs, one is connected to the rdio (Rdio-RRC) nd the other is connected to the control equipment (Control-RRC). The system is unique in the wy tht no PC is needed for the voice nd dt communiction it s hndled by the two RRC. There re two versions vilble RRC5MkII nd RRC5MkIIs, the difference is tht the (s) versions hndles two udio chnnels from the rdio which is useful together with dul receiver equipment. The Remoterig system cn be configured to work together with most Amteur rdio sttions vilble on the mrket from ICOM, Kenwood, Yesu, Elecrft, Alinco nd Tentec. The Remoterig system fits very well in the following situtions: You re not llowed to put up ntenns t your home. The noise level is too high to mke Amteur rdio ctivity possible. You wnt to build so big ntenns tht cn t be done in urbn res. You do not wnt to be dependent of PC:s for the remote control. Etc. The Remoterig system itself will not introduce ny ltency nd the ltencies introduced by Internet will rrely be ny noticeble problem. The Remoterig system lso includes unique solution for operting CW over Internet nd it lso includes CW-keyer. The Remoterig system is connected to the Internet primrily vi 0 or 00 Mbit Ethernet nd fixed connections like DSL, cble nd WLAN. 3G bsed mobile solutions will lso work but sometimes with reduced performnce. The system is portble nd you cn use it from lmost ny network connection in the world. Session control, udio (VoIP) nd dt is trnsferred using stndrdized protocols like SIP, RTP etc. where you cn select different udio qulities depending on vilble bndwidth. The RRC-5MkII is esily configured vi modern USB nd WEB bsed user interfces. Detchble control pnel You will get the ultimte function of the Remoterig system together with rdio sttions with detchble control pnels like Kenwood TS-40, Kenwood TM-D70, Kenwood TS-000, ICOM B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 7 of 9

8 IC-703, ICOM IC-70, IC-0 nd Alinco DX-SR. You simply replce the cble between the control pnel nd the rdio with the Remoterig system. You will get the sme feeling nd functionlity s with the originl setup. PC-bsed control The system lso works very well for more trditionl remote control from PC-bsed control softwre s like HmRdioDeLuxe. The Remoterig system solves the voice nd dt trnsmission but you need PC for the Control softwre itself in this setup. B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 of 9

9 Step by step system setup Below follows recommendtion bout how to proceed when setting up the system.. Spend some time to red thru this user mnul to get fmilir with the product.. Apply V DC (good stbilized power) to both units. 3. Connect both units with CAT5 ptch cbles to the sme Ethernet switch or router s your PC which you will use to setup the system is connected. 4. Downlod the Microbit Setup Mnger nd the ltest firmwre from to your PC. Follow the instructions bout how to instll the Microbit Setup Mnger (see chpter Configurtion with Microbit Setup Mnger). 5. Find out how your network is configured nd configure the RRC to fit into your network (see chpter Initil IP Setup) with the Microbit Setup Mnger. This hs to be done with both units.. Check the instlled firmwre version. If the one you downloded from Remoterig is newer, updte the units with the new firmwre. Alwys updte both units to the sme version (see chpter FW/HW bout how to updte). 7. When you hve configured the units to fit into your network, Strt your Web browser nd connect to the units one by one by entering their resp. IP-ddress. If you get in contct with their internl web server everything is OK.. Disconnect ll cbles from the units nd open the housings (see chpter Strppings nd jumpers) nd mke the hrdwre strpping ccording to the instruction which is provided in the chpter for your rdio in the end of this Users mnul. Check the red jumpers with ohm meter to verify tht they re not broken before ssembling the housings gin. 9. Mke the bsic softwre configurtion for your system which is described in the chpter for your rdio in the end of this Users mnul. 0. Prepre the cbles needed for your rdio sttion nd/or PC ccording to the cble drwings provided in the chpter for your rdio in the end of this Users mnul. Double check your home mde cbles with n ohm meter before connecting them to the RRC nd the rdio to prevent hrm of ny equipment. Microbit do not tke ny responsibility of dmged RRC-units or rdio equipment.. After prepring the cbles connect them to the RRC-units nd the rdio equipment. Connect the power to ll equipment. Check with your web browser gin tht you re in contct with both RRC-units.. Now try to estblish the connection between the Control-RRC nd the Rdio-RRC. If you use rdio with detched control pnel it s done when you press the ordinry power on button. If you re using PC-t the control end you need to browse to the sttus pge in the Control-RRC nd connect by clicking on the Connect button on. B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 9 of 9

10 3. When the connection is estblished, test the functionlity. Check tht you cn her the receiver udio, check tht PTT is working nd microphone level is OK to be sure tht the strppings re OK. 4. When this bsic functionlity re OK you cn go further connecting cbles for CW, rotor control, PA-control etc. Prepre ll functions tht you need nd test them before moving the RRC:s prt to different loctions, everything gets much more complicted to test when trvelling is needed. 5. When it s time to move the RRC:s prt you need to gther some informtion bout how the network t the remote site is configured. The first thing is to determine if your Internet Service Provider (ISP) re providing you with fixed or dynmic IP-ddress. Fixed IP:s re rre so you probbly hve dynmic IP-ddress if you re not pying extr for fixed one. A dynmic IP is no problem but you need to register DynDNS ccount (free) t They hve services which they re chrging money for but the free one hs everything you need. Follow the instructions on their website.. After moving the RRC-prt you need to connect PC to the locl network t the remote site where the Rdio-RRC should be connected nd find out how the network is configured (see chpter Initil IP Setup). You hve to set up the new IP, Netmsk nd Gtewy. When it s done use your web browser to connect to the Rdio-RRC:s internl web server nd configure the DNS IP. 7. Configure the Rdio-RRC:s DynDNS settings with the Hostnme you registered t DynDns (see chpter Dynmic DNS Setting).. Now it s time to configure your remote router. We recommend tht you first of enble the remote configuring of your router, you my need it lter. After tht s done configure DMZ or port forwrding (see chpter Network nd Firewlls). When this is done your remote Rdio-RRC should be rechble over the Internet. 9. When bck t the Control QTH try to browse to the DynDNS ddress you registered nd entered into the Rdio-RRC. You should get in contct with the Rdio-RRC internl web server exctly s it ws locl. 0. The only setting which need to be chnged in the Control-RRC is the SIP-contct t the Rdio settings pge. The SIP-contct should be chnged to the DynDNS Hostnme you registered or to the fixed IP of the Rdio QTH if you hve one. Then everything should work remotely. Enjoy the remote controlling. B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 0 of 9

11 Hrdwre Front PWR LED Green light is indicting norml sttus. When the green LED is flshing the unit is trying to connect to the Ethernet, normlly it only tkes few seconds. If the LED do not end flshing it's probbly something wrong with the network connection. USB The USB-interfce is used to initilly set up the IP prmeters. It cn lso be used for downloding new softwre (cn lso be done vi the WEB-interfce). At the Control-RRC it cn lso be used for CAT control, PTT or CW control vi the RTS nd DTR signls in the virtul COM-port delivered by the RRC USB device. COM COM cn in specil cses be used to set prmeters nd check sttuses if USB or WEB cnnot be used. The COM port cn lso be used for ex. rottor control s it cn be configured s trnsprent seril port between the RRC:s. RS-3 Pin no RS-3 Interfce (9-pol D-sub femle) TXD (Out) 3 RXD (in) 4 5 GND B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 of 9

12 7 CTS (In) RTS (Out) 9 AUX/MIC The AUC/MIC connector (RJ-45) is used for microphone connection or for connection of the rdio control pnel (IC-703/70, DX-SR). Inside the RRC behind the connector is set of strps with cn be used to decide how the connector should be configured depending on rdio or microphone. The red nd yellow LED:s re indicting SIP-sttus: LED LED Red LED Yellow Off Incoming udio strem OK SIP disconnected Flshing - SIP connection filed On Incoming udio strem fil SIP connection OK Pin no AUX (RJ45) depends on the inside strps depends on the inside strps 3 depends on the inside strps 4 depends on the inside strps 5 depends on the inside strps depends on the inside strps 7 depends on the inside strps depends on the inside strps TTL Control-RRC The TTL connector on Control-RRC (RJ-) is used primry for connection of the rdio control pnel (TS-40, RC-000 nd IC-E0) nd in other cses where you need to connect vi TTL level (5V) port. The connector is configured so stright cble cn be used to TS-40 nd RC-000 control pnel. B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 of 9

13 Pin no AUX (RJ45) AF output, Speker W/ ohm 5 TDO input, dt from pnel to rdio (TTL) 4 RDO output, dt from rdio to pnel (TTL) 3 GND V output, lwys ctive GND TTL Rdio-RRC The TTL connector on Rdio-RRC (RJ-) is used for connection of the cble which is normlly connected between the control pnel nd the rdio (TS-40, RC-000, nd IC-0). It's lso used for CAT control of rdios with 5V.s inputs e.g. ll ICOM with 3.5mm C-IV connector nd FT-x7 with the mini DIN-connector. The connector is configured so stright cble cn be used to TS-40 control pnel nd to RC-000. Pin no AUX (RJ45) AF Input (TS-40) 5 TDO input, dt to rdio (TTL) 4 RDO output, dt to rdio (TTL) 3 GND V output, lwys ctive GND SP Control-RRC At the Control-RRC the connector is used s speker output. It's connected in prllel with the udio output pins in the MIC/AUX nd TTL connectors. The connector is stndrd 3.5 mm jck for mini stereo plug nd there is no switch in the connector. The speker output power is W t ohm. In the dul RX (stereo) version there re signls from both the Min- RX nd Sub-RX vilble in the SP-connector. There is only Lf power mplifier on the Min RX signl so I recommend tht you set jumper JMP-4 in the Hedset position nd use hedset B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 3 of 9

14 or Stereo spekers with built in lf-power mplifier if you use Dul Receiver system. PC-type spekers re very well suited for this. Sub Receiver (*) Min receiver GND (*) Sub receiver, only vilble in RRC-5MkIIs version SP Rdio-RRC At the Rdio-RRC the speker connector is n input for the speker signls from the rdio. The Dul-Rx version hs inputs for both the Min-Rx nd Sub-RX. The Min-Rx input is connected in prllel with the input pins in the MIC/AUX nd TTL connector. The inputs hs resistive lods of 50 ohms. The connector is stndrd 3.5 mm jck for mini stereo plug nd there is no switch in the connector. Sub Receiver (*) Min receiver GND (*) Sub receiver, only vilble in RRC-5MkIIs version CW Control-RRC The CW knob is used for djusting the CW-speed of the built in CW-keyer. There is no knob on the Rdio-RRC. B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 4 of 9

15 Bck COM Control-RRC COM is used to connect to PC COM port (RS-3). It hs femle connector which mkes it possible to use stright cble between RRC nd PC. The communiction prmeter is set vi the web interfce. RS-3 Pin no RS-3 Interfce for PC connection (9-pol D-sub femle) RXD (out) to PC RXD 3 TXD (in) from PC TXD 4 5 GND 7 RTS - connected to JMP-3 CTS - connected to JMP-3 9 COM Rdio-RRC COM is used to connect to Rdio with RS-3 port. It hs mle connector, which mkes it possible to use stright cble between RRC nd the rdio. The communiction prmeter is set vi the web interfce. RS-3 B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 5 of 9

16 Pin no RS-3 Interfce for Rdio connection (9-pol D-sub mle) RXD (in) to pc RXD 3 TXD (out) from pc TXD 4 5 GND 7 RTS - connected to JMP-3 (*) CTS - connected to JMP-3 (*) 9 (*) Both Kenwood nd Yesu trnsceivers need the RTS nd CTS pins to be strpped together. JMP-3 inside the box cn be used to strp them if you wnt to use stndrd fully connected cble. PAD Control-RRC At the Control-RRC the input is used to connect CW-pddle. The input is for stndrd 3.5 mm stereo plug. Normlly the left pddle is connected to the tip nd the right pddle to the ring. Common is connected to the inner ring nd ground. Note tht the CW-Keyer function must be enbled to ctivte this function. PAD Rdio-RRC At the Rdio-RRC the output is used to connect the output signl from the CW-keyer to the rdio stright KEY input. The output is for stndrd 3.5 mm stereo plug. A stndrd cble with 3.5 mm connector in both ends cn often be used. Note tht the OUT mode or OUT mode must be set to Keyer to ctivte this function. PWR The RRC is powered vi the PWR connector (./5.5 mm) with 0- VDC. Rdio Control-RRC ( VDC) Rdio-RRC ( VDC) IC-70 up to 00mA, depending on mx 0 ma (0mA 0Mbit) bck lighter nd udio volume TS-40 up to 500mA, depending on mx 0 ma (0mA 0Mbit) udio volume RS-3 up to 400mA, depending on udio volume mx 0 ma (0mA 0Mbit) B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 of 9

17 V DC Pin no PWR VDC (centre) - GND RESET A short press on the reset switch will reboot the unit. By pressing nd keep the button pressed for 0 sec the unit reset to fctory defult settings with the following network settings: Control-RRC IP-ddress: Rdio-RRC IP-ddress: Netmsk: Gtewy: DNS: I/O In the I/O connector is 3() inputs nd 3 outputs, V nd GND vilble (see below). The connector is used for trnsferring signls from one RRC to the other. If the CW-keyer function is not used the connector cn be used for whtever controls signls needed in both directions. The output trnsistor cn sink mx 00mA so instll n externl rely if it's not strong enough. Pin no I/O (RJ45) IN, ctive low (CW-Keyer right-pddle) IN, ctive low (CW-Keyer left-pddle) 3 OUT, open collector (prllell with PAD Tip t Rdio-RRC) 4 IN0, ctive low (only vilble t Control-RRC) 5 OUT0 open collector OUT open collector (prllell with PAD Ring t Rdio-RRC) 7 V OUT (mx 00mA) GND B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 7 of 9

18 ETHERNET The unit cn be connected to both 0 nd 00 Mbit/s Ethernet bsed TCP/IP network. The RRC cn be configured for different connection types for Ethernet port, Auto, 0HDX, 0FDX, 00HDX, 00FDX nd Auto-with-preferred-0FDX. Defult is Auto-with-preferred-0FDX which works best in most cses. Pin no Ethernet (RJ45) Out [+] Out [-] 3 In [+] 4 5 In [-] 7 LINK Green LED indictes link OK flshing LED indictes trffic ACT Yellow LED indictes speed = 00Mbit/s (off = 0MBits/s) B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 of 9

19 Strpping nd jumpers Before connecting the RRC to your rdio you need to put some strps in plce depending on your rdio. Down below follows instructions of how to disssembly the RRC nd pictures showing where to find the different strps. : Strt with removing the screws holding the D-sub on the rer mrked COM. The tool should be 5 mm (3/"). : Open the box by pressing the D-sub until you cn get your fingers behind the edge of the lid nd cn slide the housing prt. B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 9 of 9

20 3: Behind the AUX/MIC connector there is strpping re which looks like n IC-socket. There re two rows with 9 holes. The row next to the AUX/MIC connector is connected to the connector. The strpping is done by connecting the red strp wires, supplied with the RRC, between the holes ccording to the description for the rdio (see rdio chpter). Normlly the sme strpping should be done in both Control-RRC nd Rdio-RRC. (The picture shows the strpping for IC-70). Socket Pin : Control-RRC only: JMP- is plced behind the TTL connector. With the strp in plce DC voltge is feed to the microphone element. All ICOM microphones should be DC-feed. Dynmic microphones like the ones used by Kenwood should not be DC-feed. HEIL microphones should not be DC-feed either. B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 0 of 9

21 5: Control-RRC only: JMP- is plced ner the bck of the RRC next to the RESET button. JMP- is used to select if the DC-power to the front pnels should be or 9 V. With the strp in plce it will be V, which fits ll ICOM rdios. Without the strp the voltge will be 9V, which fits Kenwood TS-40 nd RC-000 pnels tht need 9V for the bck-lighter. : JMP-3 is plced next to the rer D-sub COM. JMP 3 is used to connect RTS nd CTS together (pin 7 nd ) in COM. Most of the Yesu nd Kenwood rdios with RS-3 port need to hve them tied together. This is convenient if you wnt to use prefbricted fully connected cble. B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 of 9

22 7: JMP-4 is plced behind the CW-pot, nd is vilble only in the Control-RRC. JMP-4 is used to select between Speker level or Hedset level for the Min-Rx output. The Sub-Rx is lwys Hedset level. (JMP-4 is only present in the RRC-5MkIIs version) : When you re done you cn slide the lid on the bottom prt nd put bck the screws. Be creful the threds do not stnd to much force. B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 of 9

23 Configurtion with Microbit Setup Mnger The initil settings of the network prmeters re esiest done with the Microbit Setup Mnger. The Setup Mnger is softwre which runs under Windows on PC nd connects to the RRC vi USB (n USB cble is supplied with the RRC). The Setup Mnger cn be used for: IP Settings nd verifiction o IP-ddress o Netmsk o Gtewy o DNS o DHCP Firmwre upgrde o Appliction o Bootloder Chnging profile Strt with downloding the Microbit Setup Mnger from the homepge Instll the Microbit Setup Mnger by following the instructions which shows up. If you hve n old version of Windows P where Netfrmework.0 is not instlled, you hve to instll Netfrmework from Microsoft before instlling the Setup Mnger. When you hve finished the instlltion new shortcut to the Setup Mnger will show up on the desktop. Click on the icon to strt Setup Mnger Connect your RRC to V nd connect the USB-cble between your computer nd the USB jck on the front of the RRC. Windows will utomticlly instll the necessry drivers. When it's done the text in the bottom field will chnge from "RRC not connected" to "RRCconnected" which is n indiction tht you re in connection with the unit. B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 3 of 9

24 FW/HW version When you connect the RRC the version of the firmwre nd Bootloder will show up in the upper window. The hrdwre versions is lso shown. Go to the pge nd under downlods you cn find the ltest firmwre. If there is newer firmwre vilble downlod it to your desktop unzip it nd chnge to the "FW-updte" tb. FW updte Click on the "Select file" button nd browse to the file with the new firmwre, it should be something like RRC-5-CRC_v.4_0-0-7.bin depending on the version nd relese dte. When you hve selected the file click on the "Updte" button nd the updte process B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 4 of 9

25 will strt, the text in the bottom field will chnge to "Updting firmwre". Attention -- Do not interrupt the updte process in ny wy! After bout minute the updte is finished nd the RRC will restrt. When the text "RRCconnected" shows up gin in the lower field of the Microbit Setup Mnger, you cn chnge to the "FW/HW" tb nd check softwre version. B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 5 of 9

26 Setup The setup tb re used to setup the IP ddress nd/or select the profile (from v.44). More info bout the IP setup see Initil IP-setup. A new window wills pop-up with the bsic IP settings. Chnge the settings so they fit into your locl network nd press the "Sve" button to sve the new settings. The RRC will restrt gin nd when the text "RRC-connected" shows up gin in the lower field of the Setup Mnger, you cn click on the "Setup" button gin to verify the chnges. B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 of 9

27 Net info Click on the Get button to red the IP setting currently in use by the RRC. B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 7 of 9

28 Initil IP setup The defult Ip settings from the fctory is (Control-RRC) nd (Rdio-RRC). The net msk is nd the gtewy To be ble to contct the RRC-units vi the network you must configure the units to fit into your home network. You cn check your network configurtion from your PC. On the strt menu select Run. In the Run dilog box enter cmd. You will get DOS-window. At the DOS-promt enter ipconfig. Then you will get the needed informtion: Your PC IP ddress in this exmple is this mens tht the IP of the RRC:s must hve IP:s in the re to B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 of 9

29 The Netmsk is the Netmsk in the RRC:s should be the sme The Defult gtewy is the Gtewy in the RRC:s should be the sme In this cse ll the defult IP setting will be OK. In n other network, this is the result of the ipconfig commnd. Your PC IP ddress in this exmple is this mens tht the IP of the RRC:s must hve IP:s in the re 9... to The Netmsk is this the Netmsk in the RRC:S should be the sme The Defult gtewy is 9... the Gtewy nd in the RRC:S should be the sme The DNS should in lmost ll sitution be the sme s Defult gtewy. In this cse you must chnge the IP:s of the RRC. I recommend to use nd 9... Use the Microbit Setup Mnger to chnge the IP settings. Select the Setup tb click on the Get Setup button nd enter the IP ddresses in the Setup info dilog box. B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 9 of 9

30 B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 30 of 9

31 Configurtion with WEB-interfce Before you cn use your RRC-5MkII you must configure both the hrdwre (strpping) nd the softwre settings. The units will hve the defult IP ddresses (Control-RRC) nd (Rdio-RRC). The net msk is The configurtion is esiest done vi the web interfce. Be wre of tht your PC must be in the sme net e.g. hving n IP-number between nd nd not be the sme s the RRC. If the defult IP-ddresses of the RRC not fit your network plese use the PC-progrm Microbit Setup Mnger to chnge the IP-ddresses vi USB. It's convenient to use DHCP t the Control-RRC but wit to ctive DHCP until everything is setup nd working. Select setup pge from the links on the left side nd edit the prmeters. After ech setup pges is finished press Submit to temporry store the new settings. When you do tht new red Apply chnges button ppers on the pges. You cn now chnge prmeters on other pges but the new settings will not tke effect until you press Apply chnges. When you do tht the unit will reboot nd strt up with the new settings. If you chnge your mind fter clicking on submit you cn click on Restrt device on the left to restrt the device without chnging ny settings. B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 3 of 9

32 Info The info pge shows some sttic informtion bout the RRC s firmwre revision etc. nd lso the bsic IP-configurtion. B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 3 of 9

33 Sttus On the sttus pge you cn check some prmeters which cn be useful when debugging etc. But the most importnt is tht here is the "Connect" nd "Disconnect" button used to connect or disconnect the Internet connection between the two RRC in some modes. If the system is setup to be used with Control pnels or Twins then there is no Connect/disconnect buttons, the connection is controlled by the power on swutch on the control pnel. When connecting you will see how the SIP-sttus is chnged to "Connected/Trnsferring" if everything is OK. Here is lso shown how your NAT-router hs mpped the ports nd the momentry sttus of the inputs nd outputs nd some other things. B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 33 of 9

34 B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 34 of 9

35 Profiles The profile menu is used to store nd lod settings profiles. This could be convenient if you chnge settings often. But NO settings re needed here if you do not use it, so leve this pge to lter if it s your initil setup of the RRC:s. You cn use up to five profiles nd you cn give them describing nmes. The first time you ctivte nother profile thn the defult profile the defult profile will be copied to the other profiles. When you sve settings in the norml wy with the red pply settings button the dt will be sved in the profile which is ctive for the moment. B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 35 of 9

36 To chnge profile just select Active profile to the profile you wnt to chnge to, nd press submit. The new profile will then be loded but will not be used before restrt so you cn check ll settings nd the restrt to mke the new profile ctive. Profiles cn lso be chnged from the Setup Mnger which cn be useful if you connected it to different networks. B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 3 of 9

37 IP Settings The IP Settings menu is used to setup the initil IP prmeters needed for the unit to connect to the IP network. Down below the settings re described more in detils. B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 37 of 9

38 Prmeter Unit ID (Bnner) DHCP IP Netmsk Gtewy Dns server Extern IP/Host Eth-type Setting Text, whtever you wnt, tht will be shown t the top of the web-pge (within brckets). Used to identify different RRC. empty (defult) text Select between fixed IP ddress nd DHCP. DHCP cn be prcticl for the Control-RRC but fixed IP ddress is preferred in Rdio-RRC. No (defult) Yes IP-ddress (only when fixed IP-ddress is used) (defult Control-RRC) (defult Rdio-RRC) nnn.nnn.nnn.nnn Net msk (only when fixed IP-ddress is used) (defult) nnn.nnn.nnn.nnn Gtewy (only when fixed IP-ddress is used) (defult) nnn.nnn.nnn.nnn DNS-ddress (only when fixed IP-ddress is used) (defult) nnn.nnn.nnn.nnn Fixed externl IP-ddress of your NAT-router. Should NOT be used in norml instlltions. empty (defult) nnn.nnn.nnn.nnn Type of Ethernet connection: Auto Auto, prefer 0 Mbit (defult) 0HDX* 0FDX* 00HDX* 00FDX* Auto prefer 0 Mbit is defult s more speed is not needed nd the emissions from 0 Mbit LAN is much less thn from 00 Mbit LAN (*) If you use fixed settings you must hve mnged switch where you cn set the sme setting. B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 3 of 9

39 Web pge user Web pge pwd Enble pssword protection for the web pges nd lso the telnet connection by entering usernme (this field) nd pssword (next field). If this field is empty the RRC will not sk for pssword. Some of the pges re still ccessible but no editing is possible. empty (defult) usernme Pssword for the web pges nd telnet connection. empty (defult) pssword B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 39 of 9

40 Rdio Settings The Rdio settings re used to setup the RRC to ct together with different rdios. The settings must be done in both Control-RRC nd Rdio-RRC nd the prmeters re prtly different for the both RRC. B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 40 of 9

41 B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 4 of 9

42 Prmeter Progrm mode Sip pssword Sip contct Auto connect Setting Select the progrm mode depending on connected rdio: 0 = Trnsprent (for repeter links etc.) = ICOM CI-V (generic) = IC70 (with detched control pnel) 3 = FT-x7, FT = Kenwood, Yesu, Elecrft 5 = TS40/TM-D70 (with detched control pnel) = (*) 7 = IC-R500/IC-75(with detched control pnel) = TS-000/TM-D700 (TS-000 with RC-000) 9 = IC-0 0 = Yesu FT-950/FT-000/FT-5000/. Twin (*) = Trnsprent, 4-wire (for repeter links etc.) = DX-SR 3 = ID-E0 4 = K3 twin (*) These selections re only possible in specil editions of the RRC. (*) Only vilble in the Yesu Twin version. Protect your remote rig nd should be sme in both ends. (defult: no pssword) Control-RRC: Sets the fixed IP ddress or the DynDNS host nme to the Rdio-RRC Control-RRC: When enbled the Control-RRC will connect to Rdio-RRC immeditely fter power up in progrm mode 0,, 3 nd 4. No (defult) Yes B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 4 of 9

43 Audio qulity Sets the udio qulity depending on vilble bndwidth. Smple rte must be sme in both RRC but coding cn be different (more informtion cn be found in ppendix-a Audio coding): 0 = A-lw khz = Liner bits khz = Liner bits khz (defult) 3 = A-lw khz 4 = Liner bits khz 5 = Liner bits khz = A-lw khz 7 = Liner bits khz = Liner bits khz 9 = A-lw 4 khz 0 = Liner bits 4 khz = Liner bits 4 khz = IMA ADPCM 4 bits khz = IMA ADPCM 4 bits khz Audio Dul-RX Sets if LF from the Sub-RX should be sent s n seprte udio chnnel. Be wre of tht this doubles the need of Bndwidth. (Only vilble in the (s) version.) Codec out gin Sets the ttenution for the udio output, in 55 steps nd 0.5 db per step. Should lwys be set to = no ttenution (defult) 54 = -0.5 db 53 = -.0 db 0 = mx ttenution Codec inp gin Sets the gin for the udio input in 3 steps nd 0.75 db per step. Should be t Control-RRC for high level electret microphones nd should lwys be 0 t Rdio-RRC. 0 = defult Rdio-RRC = defult Control-RRC 3 = mx vlue B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 43 of 9

44 Codec inp HPF Hz Codec inp premp COM0 budrte COM0 dt bits COM0 stop bits COM0 prity COM0 Progrm mode 3 chr timeout Sets the low cut frequency for the udio pssbnd [Hz]: (defult) The upper cut frequency is set utomticlly depending on the smpling rte. Control-RRC: Enbles +0 db pre-mplifier for the udio input t the Control-RRC: No Yes (defult) Set COM0 budrte for the rdio communiction [bps]: (IC-R500,IC-75) 900 (IC703/70) 3400 (IC0,DX-SR,ID-E0) 5700 (TS40, TS000) Set COM0 dt bits: 5 7 (defult) Set COM0 stop bits: (defult) Set COM0 prity: 0 = Off (defult) = Odd = Even 3 = Forced- 4 = Forced-0 The chr timeout cn be progrmmed. The defult timeout should be nd works for ll rdios except FT-000 in 400 bud which need it to be set to 0. = defult 0 = FT-000 in 400 bud B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 44 of 9

45 Use USB Com Port s COM0 COM0 cn be connected to the USB interfce insted of the norml seril interfce. When instlling Microbit Setup mnger virtul Com port clled Microbit RRC Virtul Comport (COMX) is instlled. Tht s the one you should connect to when using HRD or other softwres. Yes or No (defult = No). B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 45 of 9

46 Seril Settings The seril ports COM nd COM cn be used s trnsprent seril chnnel between Control-RRC nd Rdio-RRC over Internet. The COM-ports cn be used for CAT control, rottor control etc. COM is lwys free to be used with the drwbck tht you cnnot use COM for configurtion. COM is used for the rdio control in some of the progrm modes nd cn then not be used s trnsprent seril chnnel. Rdio settings / Progrm mode COM free chnnel COM free chnnel 0 - Trnsprent yes yes - ICOM CI-V yes no IC70 yes yes 3 FT-x7, FT-000x yes no 4 Yesu, Kenwood, Elecrft yes no 5 TS40/TM-D70 yes yes (*) yes yes 7 IC-R500/IC-75(*) yes yes TS000/TM-D700 yes yes 9 IC-0 yes yes 0 Yesu FT-950/FT-000 yes no /FT-5000/FT-9000 Twin Trnsprent, /4-wire(*) yes yes DX-SR yes yes 3 ID-E0 (*) yes yes COM nd COM mode cn be configured differently depending on wht they will be used for. The sme settings must be done in both Control-RRC nd Rdio-RRC. (*) = Need specil hrdwre B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 4 of 9

47 B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 47 of 9

48 Prmeter COM mode Setting Select mode for COM-to-COM trnsprent trnsfer of seril dt between two opposite RRC. The setting defines the event tht triggers the dt trnsfer over Internet. Inctive (defult) Mode = Chr-by-chr. A dt pcket is send for ech chr, needs lot of bndwidth. Mode = ICOM CI-V. Used for CI-V control of IC-703/70 t the sme time s you use the control pnel. Mode 3 = Chr-timeout. A dt pcket is sent when there is pre-defined puse between two received chr. Mode 4 = Kenwood, Yesu, Elecrft. Used for CAT control of TS-40 or TS-000 t the sme time s you use the control pnel. Mode 5 = User-def-termintor. Used if you wnt to define the termintor chr by yourself (see below). Should be ctivted together with Mode-7 in Rdio-RRC to combine dt from COM with the other ports described bove. B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 4 of 9

49 COM budrte COM dtbits COM stop bits Mode = CAT to COM locl (Control-RRC) mkes it possible to connect for exmple logger PC which needs to spek to the Control rdio to COM t the Rdio-RRC. The IP-dt from rdio side COM nd this locl COM will be intelligent mixed (in sequence) before sent to locl COM. Dt from locl COM goes to both locl COM nd to the rdio side COM vi IP. This function is only for the Yesu Twin configurtion only. Mode = CAT to COM locl (Rdio-RRC) mkes it possible to connect other hrdwre which needs to spek to the rdio vi COM t the Rdio-RRC. The IP-dt from control side COM nd locl COM will be intelligent mixed (in sequence) before sent to locl COM. Dt from locl COM goes to both locl COM nd to the control side COM vi IP. Cn be used for MicroHm, the Web- Switch, Power Amplifier etc. This function is for Yesu, Kenwood nd Elecrft only. Mode 7 = CAT to COM locl & remote (Rdio-RRC) Sme function s bove but it lso combines dt sent from COM in Control-RRC with dt from the locl COM nd Control- RRC COM. (Remember tht this function doubles the dt mount sent over the Internet). Mode 7 = CAT to COM remote (Control-RRC) Is used in combintion with mode 7 t the Rdio-RRC. Set COM budrte [bps]: (defult) Set COM dt bits: 5 7 (defult) Set COM stop bits: (defult) B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 49 of 9

50 COM prity COM cts/rts COM termintor Use USB Com Port s COM COM mode COM dtbits COM stop bits COM prity COM termintor Set COM prity: 0 = Off (defult) = Odd = Even 3 = Forced- 4 = Forced-0 Enble the trnsfer of CTS input to RTS output of other RRC. 0 = No (defult) = Yes Defines the termintor chrcter used in COM- mode=5 (user-def-termintor). Chrcter should be in HEX-formt. 00 (defult) COM cn be connected to the USB interfce insted of the RS-3 interfce if your PC do not hve trditionl com ports. When instlling Microbit Setup mnger virtul Com port clled Microbit RRC Virtul Comport (COMX) is instlled. Tht s the one you should connect to when using HRD or other softwres. Yes or No (defult = No). Select mode for COM-to-COM trnsprent trnsfer of seril dt between two opposite RRC. The setting defines the event tht triggers the dt trnsfer over Internet. Inctive (defult) Logicl prllel with COM0. = Is used for level converting for CI-V nd FT-x7. The settings from Rdio settings re used. Mode = Chr-by-chr. A dt pcket is send for ech chr, needs lot of bndwidth. Mode = ICOM CI-V. Used for CI-V control of IC- 703/70 t the sme time s you use the control pnel. Mode 3 = Chr-timeout. A dt pcket is sent when there is pre-defined puse between two received chr. Mode 4 = Kenwood, Yesu, Elecrft. Used for CAT control of TS-40 or TS-000 t the sme time s you use the control pnel. Mode 5 = User-def-termintor. Used if you wnt to define the termintor chr by yourself (see below). See COM See COM See COM See COM B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 50 of 9

51 Use USB Com Port s COM COM cn be connected to the USB interfce insted of the RS-3 interfce if your PC do not hve trditionl com ports. When instlling Microbit Setup mnger virtul Com port clled Microbit RRC Virtul Comport (COMX) is instlled. Tht s the one you should connect to when using HRD or other softwres. Yes or No (defult = No). B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 5 of 9

52 Advnced settings Under dvnced settings it is possible to chnge the defult port numbers used by the RRC. It cn be necessry if there re more thn one RRC on your LAN or if you re using SIP bsed IP telephony (using port 500). You relly need to know wht you re doing when you chnge port numbers especilly on the Rdio-RRC so tht you don't disconnect yourself. Chnge web nd telnet port number ONLY if you hve to due to other services or more thn one RRC on your LAN. If you lose the connection cr ride might be the next thing you do. B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 5 of 9

53 Prmeter UDP cmd port UDP udio port SIP port Web server port Telnet server port Rx jitter buffer size Rx jitter dely Audio pcket size (ms) Continuous RTP Tx Debug level Setting Port number used for the Commnd chnnel. 000 (defult) Port number used for the udio chnnel 000 (defult) Port number used for the SIP session. 500 (defult) Port number used for the internl http web server. 0 (defult) Port number used for the internl telnet server. 3 (defult) Set the mximum number of udio pckets from the received udio strem tht is buffered. Dicttes mximum plybck dely. Higher vlues result in better tolernce ginst bd Internet connections. Note tht this vlue must be lrger thn the jitter dely. 4 (defult) Set the number of udio pckets received nd buffered from the udio strem before beginning plybck. Dicttes minimum plybck dely. Smll vlues gives short delys, higher vlues result in better tolernce ginst bd Internet connections but the dely will increse. Note tht this vlue must be less thn the jitter buffer size. 3 (defult) Sets the mx size (length) of the udio pckets in ms. If you hve good Internet connection with lots of bndwidth or running both RRC:s under the sme LAN/WLAN it's possible to reduce the pcket size down to ms. Smller pckets mens decresed dely but incresed bndwidth. 0 (defult) Control-RRC: If VOX will be used switch on this function. It mens tht the udio strem is sent continuously from the Control-RRC to the Rdio-RRC. This cn be security problem for some user becuse the udio from the mic is sent to the Internet ll the time. Rdio-RRC: Some mobile (3G) networks hve dely before they open up for the udio strem which ends up in problems when relesing the PTT. This function often solves this problem. No (defult) Yes Not used, nd should not be chnged. Off (defult) Low Medium High B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 53 of 9

54 Disble Audio tones Full Duplex IP Type-of-Service (dec) Mkes it possible to disble the Busy nd Error tones. No (defult) Yes Mkes it possible to use full duplex. Eg. the speker will not be muted when PTT is pressed. To use the function Continuous RTP Tx must be ctivted in the Rdio-RRC. No (defult) Yes The RTP pckets cn be tgged for ToS ccording to RFC 79 to mke it possible to use QoS in networks which support QoS. The prmeter is entered in deciml. 0 (defult) B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 54 of 9

55 Dynmic DNS setting (only Rdio-RRC) The Rdio-RRC hs DynDNS client to be used when the Internet Service Provider (ISP) uses dynmic IP ddresses insted of fixed IP ddress. If your router hs DynDNS client use tht one, nd do not ctivte more thn one DynDNS client t the sme LAN segment. DynDNS do not ccept multiple updtes from sme IP. The DynDNS client checks wht IP ddress your router hs got from the ISP nd sends the informtion to DynDNS:s DNS server. When using DynDNS you enter "Own host nme" insted of n IP ddress in the SIP contct setting in the Control-RRC nd you don't need to bother if the IP ddress t the Rdio-RRC chnges. You need to register n ccount (free of chrge) t nd get domin nme. There re other providers of the sme service but RRC-5MkII only supports DynDNS. Be wre of tht new free DynDNS ccounts hve lot of limittions compred to ccounts registered few yers go. B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 55 of 9

56 Prmeter DynDNS check intervl Own host nme Usernme Pssword Setting Sets how often the externl IP ddress of your router should be checked, vlue in minutes: Off (DynDNS client disbled) Domin nme registered t DynDNS.com. Exmple: my-rdio-site.hm-rdio-op.net DynDNS ccount usernme. DynDNS ccount pssword. B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 5 of 9

57 Keyer Settings (Control-RRC) A very powerful function for remote CW opertion is implemented in the RRC-5MkII. The system is ble to hndle delys nd jitter cused by Internet in unique wy. This function is lso dependnt on the I/O configurtion, see IO settings. Prmeter Setting Enble Enble the CW-keyer function. No = CW-keyer is off (defult) Yes = CW-keyer is on Imbic Set the CW-keyer imbic mode. Old type, squeeze keyer Mode-A Mode-B (defult) Mode-B + uto-chr-spce Pddle reverse Set the reverse mode for the CW-pddle. No, left pddle dot & right pddle dsh (defult) Yes, left pddle dsh & right pddle dot B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 57 of 9

58 Weight Side tone hz Side tone -db Lf dely ms Key dely ms Time rtio between dsh nd dot =.5-4.0/ 30 = 3.0/ (defult) Frequency for the side-tone in Hz. 0, = side-tone frequency in Hz 00 = 00 Hz (defult) 0 = No locl side tone is generted, cn be used to test how the CW sounds if you enble side tone in the rdio nd send with memory keyer or PC. Audio level for the side-tone in db = udio level in db 0 = -0 dbm (defult) Mute (dely) time for udio from the rdio t Control-RRC fter dot/dsh commnd. Recommendtion - strt with sme vlue s the ping time = dely in milliseconds 0 = no dely (defult) Dely time before the keying of the rdio is executed t RRCrdio = dely in milliseconds 0 = no dely (defult) B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 5 of 9

59 Keyer Settings (Rdio-RRC) In the Rdio-RCC only one prmeter is vilble. PTT-ctivted by keyer is function tht is useful if you wnt the PTT input of the rdio to be ctivted when using the Remoterig keying function. The PPT is ctivted before the Key dely mening tht PA for exmple cn be ctivted x ms before the keying signl is ctivted to prevent hot switching. Prmeter PTT ctivted by keyer Setting Enble the PTT function. No = (defult) Yes = PTT is ctivted by the keyer B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 59 of 9

60 IO Settings The inputs nd outputs in both the Control-RRC nd Rdio-RRC re configurble to meet different needs. Control-RRC: Prmeter IN0 mode Setting Select the function for Input-0 (IN0) signl in the I/O connector. 0 = I/O, input sttus is trnsferred to Rdio-RRC (defult) = Keyer, stright key or externl keyer = PTT, PTT-switch or foot-switch etc. B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 0 of 9

61 OUT0 mode OUT mode OUT mode USB RTS s PTT USB DTR s CW Output 0 cn only be configured for one of two functions. I/O = Indicting tht SIP connection is up. Keyer = The output follows the Keyer output. OUT mode Output cn be configured for one of two functions. I/O = The output follows Input from the Rdio-RRC. Keyer = The output follows the Keyer output. Output cn cn be configured for one oftwo functions. I/O = The output follows Input from the Rdio-RRC. Keyer = The output follows the Keyer output. Select which of the USB virtul COM ports RTS signl which should be used s externl PTT. Useful when using Logging softwre, RTTY progrms etc. Disbled = (defult) COM0 = COM0 rts is used s PTT control COM = COM rts is used s PTT control COM = COM rts is used s PTT control Select which of the USB virtul COM ports DTR signl which should be used s CW key input. Useful when using Logging softwre, RTTY progrms etc. Disbled = (defult) COM0 = COM0 dtr is used s CW key input COM = COM dtr is used s CW key input COM = COM dtr is used s CW key input B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 of 9

62 Rdio-RRC: B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 of 9

63 Prmeter OUT0 mode OUT mode OUT mode Setting Select the function for output-0 (OUT0) signl the I/O connector. 0 = I/O, ctive when IN0 on Control-RRC is ctive (Control-RRC IN0-mode setting must be in stte I/O). (defult) = Keyer, output to the rdio stright key input = PTT, used s externl PTT 3 = Connect, ctive when the SIP-connection is ctive 4 = On/Off, controlled by the ON/OFF button on this side (*) 5 = Keyer PTT, ctive when CW is send vi the keyer (cn be used to key PA). If you set key dely in the Control-RRC this output will be ctivte key dely ms before the ctul CW-keying is strted. = Budot/45 used s output for RTTY bud. RTTY input vi USB virtul com port t Control-RRC. Connect PC softwre to the virtul com nmed FSK COM. Select the function for output- (OUT) signl the I/O connector (or tip in the PAD-jck). 0 = I/O, ctive when IN0 on Control-RRC is ctive. (Control-RRC CW- Keyer function must be disbled). (defult) = Keyer, output to the rdio stright key input = PTT, used s externl PTT 3 = Connect, ctive when the SIP-connection is ctive 4 = On/Off, controlled by the ON/OFF button on this side (*) 5 = Keyer PTT, ctive when CW is send vi the keyer (cn be used to key PA). If you set key dely in the Control-RRC this output will be ctivte key dely ms before the ctul CW-keying is strted. = Budot/45 used s output for RTTY bud. RTTY input vi USB virtul com port t Control-RRC. Connect PC softwre to the virtul com port nmed FSK COM. Select the function for output- (OUT) signl the I/O connector (or ring in the PAD-jck). 0 = I/O, ctive when IN0 on Control-RRC is ctive. (Control-RRC CW- Keyer function must be disbled). (defult) = Keyer, output to the rdio stright key input = PTT, used s externl PTT 3 = Connect, ctive when the SIP-connection is ctive 4 = On/Off, controlled by the ON/OFF button on this side (*) 5 = Keyer PTT, ctive when CW is send vi the keyer (cn be used to key PA). If you set key dely in the Control-RRC this output will be ctivte key dely ms before the ctul CW-keying is strted. = Budot/45 used s output for RTTY bud. RTTY input vi USB virtul com port t Control-RRC. Connect PC softwre to the virtul com port nmed FSK COM. (*) When the ON/OFF buttons re pushed the output chnge will be immedite, but will resume to lst sved position fter power on. To mke the chnges permnent use the "pply chnges" button. B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 3 of 9

64 Ping settings (only Rdio-RRC) The Rdio-RRC hs Ping Wtchdog function which cn be used s n extr security. This function is quite common in network equipments. It cn be set to ping n IP ddress nd when it does not get ny nswer, it will mke hrd reboot of the RRC. The sttus of the ping wtchdog cn be checked t the sttus pge. This function is only vilble on the Rdio-RRC. Enble ping wtchdog IP ddress to ping Ping Intervl (seconds) Strtup dely (seconds) Filure count to reboot Enbles the function. No = Function is disbled Yes, test = Function enbled but it will not ctully reboot, cn be used for test Yes, reboot = Function is enbled. IP ddress to ping is entered here, In norml cses use the Gtewy IP. Intervl between the ping is sent. (-5535, defult 300 s) Dely before the first ping is sent. ( ), defult 300 s. If Test mode is ctivted it cn be set to Sets how mny times the ping is llowed to fil before reboot is done. (-55, defult 3 ) B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 4 of 9

65 Export settings (HTML) This function cretes text file with the ctul settings nd sttus of the unit. This file cn be sent vi emil for support purposes for exmple. Export settings (bin) This function is used to bckup your settings to file in your PC. When clicking on the link dilog box will show up where you cn decide where to store nd the nme of your bckup file. Note! The exported file will only include settings for the ctive profile. B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 5 of 9

66 Import settings (bin) This function is used import your bckup file from your PC. Click on select file nd browse to your file nd then click import. Note tht the imported settings will be stored in the currently selected profile. B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 of 9

67 Appliction firmwre upgrde The ppliction firmwre cn be updted over the Internet vi the web interfce when bugs re fixed nd/or new functionlity is implemented. You don't hve to be where the RRC- 5MkII is to do the updtes. Downlod the new firmwre from nd sve the file on your computer (it hs nme like RRC5-CRC_v.3_ bin). Connect to the RRC you wnt to updte nd select 'Appliction-upgrde'. Then click on the 'Browse' button nd select the file with the new firmwre. After tht you click on the 'Upgrde' button nd the new firmwre will be trnsferred nd sved into the RRC. When the firmwre is updted the RRC will restrt. Note -- Do not interrupt the upgrde process in ny wy. Wit minute or two then connect to the RRC gin nd select 'Info' nd verify tht the Softwre version is updted. If it looks like its not updted empty the web browser cche, to prevent it from showing n old cched pge. The updte NEVER fils but the browser is common problem. B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 7 of 9

68 Bootloder firmwre upgrde This follows the sme steps s the ppliction firmwre upgrde procedure bove. Restrt device Restrt device cn be used if you wnt to reset nd restrt the RRC without sving ny chnges (before pply chnges) or just for ordinry reset. B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 of 9

69 Configurtion with terminl-interfce All prmeters cn lso be progrmmed vi the seril interfce COM (RS-3) or Telnet port. COM hs the following settings: 3400 bud, bits, No prity, nd stop bit. Select the sys [s] nd setup-edit [] menus to configure the RRC. This method of configurtion is not user friendly nd should be voided. ========================= : udio c: codec d: debug e: extio f: flsh i: sip l: led q: udio qulity p: power r: rdio s: sys u: usb ========================= s sys ========================= : setup edit : setup view 3: setup cler 4: sntp 5: rtc : wdt reset 7: dns query : show network info 9: STUN test 0: memory : UDP send b: UDP receive c: Setup defult (Control) d: Setup defult (Rdio) r: COM-rts/cts on/off q: exit B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 9 of 9

70 CW-Keyer Generl The RRC-5 hs CW-keyer function tht mkes CW opertion possible over Internet even if there re long ltencies nd lots of jitter. Note tht the CW-keyer is by defult disbled. The CW-keyer side-tone is generted loclly t the control RRC. When the dot or dsh is executed the udio from the rdio cn be muted t the Control-RRC to disble the rdio sidetone or nnoying clicks nd sounds. The time the mute function is ctive is defined by the lfdely setting. The vlue of lf-dely depends on the ltency of Internet. A good strt vlue is the sme vlue s the ping time between control nd rdio QTH. Another unique feture is kind of djustble jitter buffer t the rdio end. If the Internet connection hs vrying ltencies, you cn set key-dely before the keying of the rdio is executed. This dely mkes it possible to reconstruct the trnsmission on-the-fly nd the system will be much more tolernt ginst vrying ltencies (jitter). Longer key-delys give higher tolernce ginst jitter but lso dd dely until the keying is executed t the rdio. Even if you hve good connection you could try with low vlue. Remember tht when you increse this vlue you must lso increse the lf-dely vlue. Settings Keyer settings: Control Rdio Enble Yes Imbic Mode-A Pddle reverse No Weight [5-40] 30 Side tone hz [ ] 00 Side tone db [50-0] 0 Lf dely [0-500] 0 Key dely [0-50] 0 IO settings: Control Rdio IN0 mode USB DTR s CW OUT0 mode OUT mode OUT mode I/O No I/O I/O Keyer B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 70 of 9

71 Connections PAD Control-RRC: At the Control-RRC the PAD-jck is used to connect CW-pddle. The input is for stndrd 3.5 mm stereo plug. The left pddle is connected to the tip nd the right pddle to the ring. Common is connected to the inner ring nd house. Note - these signls re lso vilble in the I/O-connector. Signl PAD jck IO setting left-pddle tip - right-pddle ring - gnd inner ring - PAD Rdio-RRC: At the Rdio-RRC the PAD-jck is used to connect the output signl from the CW-keyer to the rdio stright-key input. The output is for stndrd 3.5 mm stereo plug. A stndrd cble with 3.5 mm connector in both ends cn often be used. Note - these signls re lso vilble in the I/O-connector. Signl PAD jck IO setting keyer-output tip OUT mode = Keyer keyer-output ring OUT mode = Keyer gnd inner ring - USB Control-RRC: A PC with stright-key functionlity cn be used to perform the keying, lone or in combintion with CW-pddle. To ctivte keying the PC could use the DTR signl in the virtul USB COM-port delivered by the RRC USB device. The PC control works in prllel with the CW-pddle so it is possible to shift between PC-keying nd the CW-pddle without chnging the configurtion. I/O-connector Control-RRC: A PC with stright-key functionlity or other externl keyer cn be used to perform keying, lone or in combintion with CW-pddle. To ctivte keying connect pin-4 (IN0) to GND. The externl keyer works in prllel with the CW-pddle so it is possible to shift between externl keying nd the CW-pddle without chnging the configurtion. Note - The stright-key input (IN0) is generic input nd cnnot be connected direct to PC, you need n interfce, see ppendix. B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 7 of 9

72 Signl I/O connector IO setting right-pddle (IN) - left-pddle (IN) - stright-key/pc 4 (IN0) IN0 mode = Keyer gnd - I/O-connector Rdio-RRC: The output signl from the CW-keyer to the rdio stright-key input cn lso be found in the I/O connector. Signl I/O connector IO setting keyer-output 3 (OUT) OUT mode = Keyer keyer-output 5 (OUT0) OUT0 mode = Keyer keyer-output (OUT) OUT mode = Keyer gnd - DASH DOT FROM PC RRC-5 I/O Con -pol RJ 45 Con -pol RJ 45 Con KEY INP 3,5/,3 mm stereo plug GND IN0 IN IN OUT 0 GND PADDLE B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 7 of 9

73 RTTY Keying Generl Most HF-rdios hve specil FSK/RTTY keying input which is better to use thn AFSK (udio frequency shift keying) since you don t need to set mic gin nd other settings. The RRC-5 hs seprte seril chnnel for trnsfer of bud RTTY keying dt. The RTTY seril chnnel is only vilble vi the USB interfce. When instlling the Microbit Setup mnger USB-driver clled COMFSK is instlled In your RTTY PC-Softwre you should select the serilport number ssigned to the driver by Windows, in the exmple bove it s COM4. B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 73 of 9

74 At the Rdio-RRC IO-settings pge you need to select which output you wnt to use for the RTTY keying signl. RTS from the RRC-5 COMFSK USB port is used to key PTT. B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 74 of 9

75 RTTY with MMTTY The Remoterig specific settings to use MMTTY for RTTY is shown below. At the TX tb select the PTT & FSK comport to the sme comport s Device Mnger showed to be ssigned to RRC-5 COMFSK port, in this exmple it s COM4. B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 75 of 9

76 At the Misc tb e select COM-TxD(FSK) nd click on the USB Port button. B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 7 of 9

77 In the USB port option dilog select C-limiting speed. If not limiting speed is selected the PTT will be relesed before the whole RTTY string is sent, becuse the USB communiction is so much fster thn ordinry RS-3 seril port. Settings IO settings: Control Rdio OUT0 mode - OUT mode Budot/45 OUT mode Keyer B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 77 of 9

78 Connections PAD Control-RRC: Only the USB interfce cn be used for RTTY s described bove. PAD Rdio-RRC: At the Rdio-RRC the PAD-jck cn be used to connect the RTTY signl from the FSK seril port. The PAD will then be shred with CW key output. The pd jck is for stndrd 3.5 mm stereo plug. Note - these signls re lso vilble in the I/O-connector. Signl PAD jck IO setting keyer-output tip - keyer-output ring OUT mode = Budot/45 gnd inner ring - USB Control-RRC: A PC with suitble softwre like MMTTY cn be used to perform the RTTY keying. Together with the RTTY keying signl PTT need to be ctivted this is done by ctivting the RTS signl in the virtul comport (COMFSK). MMTTY does this by defult other softwre my need mnul configurtion. I/O-connector Rdio-RRC: The output signl for the RTTY keying cn lso be found in the I/O connector. Signl I/O connector IO setting RTTY-output 3 (OUT) OUT mode = Budot /45 RTTY -output 5 (OUT0) - RTTY -output (OUT) - gnd - The I/O connector cn lso be used for the PTT signl if the Mic PTT is not used. If you wnt this function chnge one of the free outputs to PTT. B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 7 of 9

79 ICOM CI-V Generl RRC-5MkII supports the CI-V protocol used by lmost every ICOM rdio. Then you hve to use PC-softwre e.g. HmRdioDeLuxe or similr rig control softwre t the control site. All udio nd dt communiction goes true the RRC:s nd you don't need PC t the remote site. The Connect/Disconnect button on the web sttus pge is used to connect/disconnect to/from the remote site. It cn lso be done by the UP-button on the microphone or be set to lwys be connected. Hrdwre configurtion Norml: B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 79 of 9

80 SIP-Connect/disconnect vi MIC UP button: Rdio settings (exmple) Prmeter Control Rdio Progrm mode ICOM CI-V ICOM CI-V SIP pssword hello hello SIP relm SIP contct Auto connect No Audio qulity Liner bits khz Liner bits khz Audio dul-rx (*) No Codec out gin Codec inp gin 0 Codec inp premp Yes Codec inp HPF Hz 3 3 COM0 budrte COM0 dt bits COM0 stop bits COM0 prity 0 - Off 0 - Off (*) Avilble only in RRC-5MkIIs, remember tht the bndwidth demnd is doubled. Connections Drwings of the connection cbles cn be found under ppendix B. Control-RRC: Connect Remoterig-I0c cble or stndrd RS-3 cble between the PC nd the RRC COM. B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 0 of 9

81 The microphone cn be connected direct to the RRC AUX/MIC connector if you hve microphone with RJ-45 connector, like the HM-03. If you hve microphone with circulr connector like HM-3 you hve to use the Remoterig I0 cble, the OPC-59, from ICOM or mke one by yourself (drwing for I0 is provided). The speker is connected direct to the RRC SP-jck with 3.5 mm stereo plug. Rdio-RRC: From the RRC TTL connector to the rdios CI-V jck you cn use the Remoterig Ic cble or mke it by your self. The cble should hve 4/ modulr connector in one end nd 3.5 mm stereo plug in the other end. The 3.5 mm plug is connected to the rdio CI-V jck. Between the RRC AUX/MIC connector nd the rdios microphone jck you cn connect stndrd ptch cble if the rdio hve RJ-45 jck. If the rdio hve circulr microphone jck you cn use the Remoterig I or mke the cble by yourself. (drwings for I is provided). Mke the cble s short s possible to prevent it from picking up HF. The speker signl from the rdios externl speker jck to the RRC SP jck is connected vi stndrd "off- the-shelf cble with 3.5 mm stereo plugs in both ends. I,I0 B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 of 9

82 Mic Inp -pol Circulr mle I0 screened 0 cm : Generic ICOM cbles RRC-5MkII -pol RJ 45 Con 5 Cble I0 () USER MANUAL UP AF V UP PC COM Front pnel view GND MIC MICE PTT DSUB- 9pol Femle RRC-5MkII GND MIC MICE PTT I0c DSUB- 9pol Mle V SPEAKER 3.5 mm stereo plug B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 of 9

83 SPEAKER 3.5 mm stereo plug TTL 4/ modulr RRC-5MkII GND RDO TDO Ib Ic : Generic ICOM cbles RRC-5MkII Cble I () Front pnel view SPEAKER 3.5 mm stereo plug CI-V 3.5 mm stereo plug USER MANUAL PTT PTT MIC MIC AUX/MIC -pol RJ 45 Con V AF MICE GND PWR ON indiction I screened m V -pol Circulr femle AF MICE GND B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 3 of 9

84 ICOM IC-703, IC-70 Generl The ide of remote controlling IC-703/70 is simple; it's just to extend the cord between the rdio nd the control pnel using Internet. When you press the power button on the pnel the rdio comes to life t the remote side nd sound nd pnel info flows cross the Internet between the pir of RRC-5MkII:s. The look nd feel of the pnel is the sme s if the pnel ws directly connected to the rdio. Hrdwre configurtion B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 4 of 9

85 Rdio settings (exmple) Prmeter Control Rdio Progrm mode IC70 IC70 SIP pssword hello hello SIP relm SIP contct Auto connect No Audio qulity Liner bits khz Liner bits khz Audio dul-rx (*) No Codec out gin Codec inp gin 0 Codec inp premp Yes Codec inp HPF Hz 3 3 COM0 budrte COM0 dt bits COM0 stop bits COM0 prity 0 - Off 0 - Off (*) Avilble only in RRC-5MkIIs. Connections All necessry signls between the pnel nd the rdio re connected with the wires in the cble OPC-5 or OPC-57 from ICOM. We just need to cut it prt nd connect RRC- 5MkII in ech end. The following signls re represented in the cble, (the numbering is for the RJ45 connector to the RRC fter converting the cble, not for the ICOM connector): V power to control pnel (only when rdio is ON) LRXD - seril dt 900 bps from pnel to rdio 3 AF - udio to speker. 4 PWK - power control, grounding it switch on the rdio 5 MICE - mic ground MIC- mic Signl 7 GND LTXD - seril dt 900 bps from rdio to pnel Cut the ICOM cble (OPC-5 or OPC-57) nd connect both ends to stndrd CAT-5 ptch cble for computer networks, use shrinking tubes to protect the soldering. One problem is tht the ICOM cble is very soft nd there is more sewing tred thn copper wire. The copper wire is lso vrnished to mke it even more difficult. Before you connect the cbles to the RRC:s, plese check the cbles by connecting them together with xrj45 connector. Also py ttention to tht speker or hedset must be connected to the speker jck on the IC- 70 front-pnel otherwise the no udio will be sent from the microphone to the rdio. B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 5 of 9

86 Power supply Control-RRC: The Control-RRC is supplied with common 3, V (0-V) power supply. The disply nd speker mplifier needs lot of power so you need A. Rdio-RRC: The Rdio-RRC should be supplied from the sme power supply s the rdio to void humming. Plese put smll fuse on the cble if you connect it to 30 Amp PS. B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 of 9

87 : Splitted Cble for IC70 RRC 5 / RRC-5MkII (CAT-5) 5 Cble () USER MANUAL Pnel Rdio -pol ICOM-con -pol RJ 45 Con -pol RJ 45 Con -pol ICOM-con 3 Blue V Ornge/White Ornge/White V Blue 3 Yellow LRXD Ornge Ornge LRXD Yellow 4 Red AF Green/White 3 3 Green/White AF Red 4 White PWK Blue 4 4 Blue PWK White 5 MICE Blue/White 5 5 Blue/White MICE 5 White MIC MIC White 7 GND 7 7 GND 7 Blck LTXD LTXD Blck Screen to White Screen to White Green Green Screen to Red Brown/White Brown/White Screen to Red Convert from ICOM-cble to -pol CAT-5 cble Brown Brown Convert from ICOM-cble to -pol CAT-5 cble B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 7 of 9

88 Prepre the seprtion cble to IC-703 nd IC-70 The cble between front nd rdio before it is cut prt. You hve to buy this cble from your locl ICOM-deler (rt no OPC-5 or OPC-57). Connector t rdio end. Connector t control pnel end. B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 of 9

89 - Identify the end with the connector to the rdio, se bove. - Cut the cble prt, don't mke it longer then needed t rdio end. The mic signl is sensitive of HF from ntenns etc. s usully. - Tke wy bout 40 mm of the outer covering. - Seprte the shields from the inner wire, the red wire hs copper coloured shield nd the white hs green shield. The shielded white wire is thinner thn the white one without shielding. Tht wy you cn identify them from ech other. The outer shielding is not connected to the RRC. - Cut ll wire to bout 0 mm. Tke wy bout 3 mm of the cover from ech wire nd tin-plte them. It's not esy but it's possible. - Also tin-plte the copper nd green shielding. - Use the supplied CAT-5 cble cut of 0-5 cm from ech connector nd tke wy 40 mm of the outer cover. - Seprte the pirs. - Tke wy 3 mm of the cover from ech wire nd tin-plte them. - Identify the following colours:. Ornge/White. Ornge 3. Green/White 4. Blue 5. Blue/White. Green 7. Brown/White. Brown B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 9 of 9

90 - Cut piece of shrinking tube to ech wire. Cut them short enough so they don't shrink from the het of the solder iron. - First tred 00 mm long,4 mm shrinking tube on the seprtion cble. - Then tred 0 mm long,4 mm shrinking tube on the seprtion cble. - Solder them together, follow the drwing bove. - Tred the shrinking tubes over the soldered joints nd shrink them with hot ir. B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 90 of 9

91 - Tred the.4 mm shrinking tube over the joint nd shrink it with hot ir. - Tred the second shrinking tube over the first nd shrink them with hot ir - The first cble is now finished, Do the sme with the other prt. The one with the connector to the control pnel. When you hve finished both cbles, connect them together with the supplied RJ45 extender. - Check the cble with n ohm-meter. You should hve connection from pin t rdio end to pin t rdio end etc. Also check for short circuits between the pins. - Connect the cble between pnel nd rdio nd check the functionlity. Don't forget the microphone. ( this should be done without involving the RRC.s t this moment. When everything is OK you cn connect the cbles to the RRC:s B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 9 of 9

92 ICOM IC-R500 Generl The technicl solution is the sme s for IC-70 nd TS-40; you cn remote control the receiver over Internet from the control pnel without ny PC. We simply replce the cble between the control pnel nd the receiver with two RRC-5 units, one t the control pnel nd one t the receiver. When you push the PWR-ON button n udio nd dt connection is estblished between the units nd you control the receiver s you do normlly with the control pnel ttched directly to the receiver. Hrdwre configurtion Rdio settings (exmple) Prmeter Control Rdio Progrm mode 7 ICR500 7 ICR500 SIP pssword hello hello SIP relm SIP contct Auto connect No Audio qulity Liner bits khz Liner bits khz Audio dul-rx (*) No/Yes Codec out gin Codec inp gin 0 Codec inp premp Yes Codec inp HPF Hz 3 3 COM0 budrte COM0 dt bits COM0 stop bits COM0 prity 0 - Off 0 - Off B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 9 of 9

93 (*) Avilble only in RRC-5MkIIs, remember tht the bndwidth demnd is doubled. Connections The cbling is quite simple nd cn be done with simple RJ connectors. Power supply Control-RRC: The Control-RRC is supplied with common 3, V (0-V) power supply. The disply nd speker mplifier needs lot of power so you need A. Rdio-RRC: The Rdio-RRC should be supplied from the sme power supply s the rdio to void humming. Plese put smll fuse on the cble if you connect it to 30 Amp PS. B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 93 of 9

94 Control Pnel IC-R500 -pol Modulr PWR SW PWR SW GND GND RDO RDO TDO TDO HV HV : ICOM cble RRC-5MkII to IC-R500 Pnel end RRC-5MkII MIC/AUX pol Modulr Con Cble I4 () SPEAKER 3.5 mm stereo plug USER MANUAL B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 94 of 9

95 SPEAKER 3.5 mm stereo plug RRC-5MkII MIC/AUX pol Modulr Con Control Inp IC-R500 pol Modulr Con : ICOM cble RRC-5MkII to IC-R500 Rdio end 5 Cble I5 () SPEAKER 3.5 mm stereo plug USER MANUAL PWR SW PWR SW GND GND RDO RDO TDO TDO HV HV B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 95 of 9

96 ICOM IC-E0 Generl It's not only shortwve trnsceivers which could be remote controlled, the remoterig system lso support ICOM:s D-str rdio IC-E0. The technicl solution is the sme s for IC-70 nd TS-40; you cn remote control the rdio over Internet from the control pnel without ny PC. We simply replce the cble between the control pnel nd the rdio with two RRC- 5 units, one t the control pnel nd one t the rdio. When you push the PWR-ON button n udio nd dt connection is estblished between the units nd you control the rdio s you do normlly with the control pnel directly ttched to the rdio. Hrdwre configurtion Rdio settings (exmple) Prmeter Control Rdio Progrm mode 9 IC-E0 9 IC-E0 SIP pssword hello hello SIP relm SIP contct Auto connect No Audio qulity Liner bits khz Liner bits khz Audio dul-rx (*) No Codec out gin Codec inp gin 0 Codec inp premp Yes B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 9 of 9

97 Codec inp HPF Hz 3 3 COM0 budrte COM0 dt bits COM0 stop bits COM0 prity 0 - Off 0 - Off (*) Avilble only in RRC-5MkIIs Connections The cbling is quite simple nd cn be done with simple RJ connectors. Be wre of tht the originl microphone cn not be used without the HM-33 dpter bords. If you do not hve them use simple ICOM microphone like HM-03 or HM-95. Microphones with circulr connectors cn lso be used with dpter cble OPC-59. Control-RRC: You hve to mke the control cble I3 to connect between the Control pnel nd the RRC TTL connector. Mrk up the cble so you connect the connectors to the right unit, it will not work if you try to use it connected bckwrds. The microphone cn be connected direct to the RRC AUX/MIC connector if you hve microphone with RJ-45 connector. The speker is connected direct to the RRC SP-jck with 3.5 mm stereo plug. Rdio-RRC: You hve to mke the control cble Ib to connect between the Rdio-RRC nd the Rdio. Mrk up the cble so you connect the connectors to the right unit, it will not work if you try to use it connected bckwrds. Between the RRC AUX/MIC connector nd the rdios microphone jck you cn connect stndrd ptch cble (CAT5 or CAT) I. The speker signl from the rdios externl speker jck to the RRC SP jck is connected vi stndrd "off- the-shelf cble with 3.5 mm stereo plugs in both ends. Using HM-33 Microphone If you hve RRC-5MkIIs you cn buy the HM-33 dpter pcbs which let you use the HM-33 microphone with ll it s buttons. B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 97 of 9

98 The smll pcbs re mounted in the strpping sockets which mens tht no red strps re needed. The pcb with the yellow cble re mounted in the Control-RRC nd the pcb with the blue cble re mounted in the Rdio-RRC. The yellow nd blue cbles need to be solder to one point on the RRC pcb. See pictures below. Be sure to remove power when solder. There No settings need to be chnged fter mounting the pcbs. There is one solder pd which is significntly bigger thn the other vi holes to the right of the CPU over the Crystl. Tht s the one which the cbles should be soldered to. Control-RRC B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 9 of 9

99 Rdio-RRC B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 99 of 9

100 Power supply Control-RRC: The Control-RRC is supplied with common 3, V (0-V) power supply. The disply nd speker mplifier needs lot of power so you need A. Rdio-RRC: The Rdio-RRC should be supplied from the sme power supply s the rdio to void humming. Plese put smll fuse on the cble if you connect it to 30 Amp PS. B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 00 of 9

101 4 Control Pnel IC-E0 4-pol Modulr 3 4 V GND TDO RDO I3 RRC-5MkII TTL 4/ pol Modulr Con V GND RDO TDO : ICOM cble RRC-5MkII to IC-0 Pnel end SPEAKER 3.5 mm stereo plug 5 Cble I3 () USER MANUAL B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 0 of 9

102 SPEAKER 3.5 mm stereo plug RRC-5MkII -pol RJ 45 Con RRC-5MkII 4/ pol Modulr Con Mic Inp IC-E0 -pol RJ 45 Con Control Inp IC-E0 4/ pol Modulr Con V V 3 GND GND 3 4 RDO TDO 4 5 TDO RDO 5 Ib : ICOM cble RRC-5 to ICOM IC-E0 Rdio end SPEAKER 3.5 mm stereo plug 5 Cble I () USER MANUAL MIC MIC 7 7 Try Stndrd shielded CAT 5 PTT PTT MICE MICE GND GND I Ic B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 0 of 9

103 ICOM ID-E0 Generl The Remoterig system lso support ICOM:s D-str rdio ID-E0. The technicl solution is the sme s for IC-70 nd TS-40 etc. You cn remote control the rdio over Internet from the control pnel without ny PC. We simply replce the cble between the control pnel nd the rdio with two RRC-5 units, one t the control pnel nd one t the rdio. When you push the PWR-ON button n udio nd dt connection is estblished between the units nd you control the rdio s you do normlly with the control pnel directly ttched to the rdio. Hrdwre configurtion The hrdwre preprrions is little bit more complicted for the IC-E0 s some modifictions must be done t the Remoterig circuit bords. The HM-33 dpters must be mounted nd wire must be connected, more info below. Rdio settings (exmple) Prmeter Control Rdio Progrm mode 3 IC-E0 3 IC-E0 SIP pssword hello hello SIP relm SIP contct Auto connect No Audio qulity Liner bits khz Liner bits khz Audio dul-rx (*) No Codec out gin Codec inp gin 0 Codec inp premp Yes Codec inp HPF Hz 3 3 COM0 budrte COM0 dt bits COM0 stop bits COM0 prity 0 - Off 0 - Off (*) Avilble only in RRC-5MkIIs Connections The cbling is quite simple nd cn be done with simple RJ connectors. Be wre of tht the HM-33/0 dpter bords must be used B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 03 of 9

104 Drwings of the connection cbles cn be found below. Control-RRC: You hve to mke the control cble I0 to connect between the Control pnel nd the RRC TTL connector. Mrk up the cble so you connect the connectors to the right unit, it will not work if you try to use it connected bckwrds. The microphone cn be connected direct to the RRC AUX/MIC connector if you hve microphone with RJ-45 connector. The speker is connected direct to the RRC SP-jck with 3.5 mm stereo plug. Rdio-RRC: You hve to mke the control cble I9 to connect between the Rdio-RRC nd the Rdio. Mrk up the cble so you connect the connectors to the right unit, it will not work if you try to use it connected bckwrds. Between the RRC AUX/MIC connector nd the rdios microphone jck you cn connect stndrd ptch cble (CAT5 or CAT). The speker signl from the rdios externl speker jck to the RRC SP jck is connected vi stndrd "off- the-shelf cble with 3.5 mm stereo plugs in both ends. HM-33/0 Microphone dpter bords If you hve RRC-5MkIIs you cn buy the HM-33/0 dpter pcbs which re needed for the function together with the IC-E0. The smll pcbs re mounted in the strpping sockets which mens tht no red strps re needed. The pcb with the yellow cble re mounted in the Control-RRC nd the pcb with the blue cble re mounted in the Rdio-RRC. The yellow nd blue cbles need to be solder to one point on the RRC pcb. See pictures below. Be sure to remove power when solder. There is no settings tht need to be chnged fter mounting the pcbs. B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 04 of 9

105 There is one solder pd which is significntly bigger thn the other vi holes to the right of the CPU over the Crystl. Tht s the one which the cbles should be soldered to. Control-RRC Rdio-RRC B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 05 of 9

106 Modifictions of the Control-RRC circuit bord One resistor must be removed nd wire must be solder between two pds. You need fine solder iron nd short piece of insulted thin wire nd mybe little piece of tin. Don t use ny soldering brid or pumps they my dmge the pcb. - Remove the resistor by heting the ends of the resistor, lternte from left to right end stying few seconds t ech end until the component come loose. B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 0 of 9

107 - Solder the thin insulted wire between the solder pds s shown on the picture below. Modifictions of the Rdio-RRC circuit bord One resistor must be removed nd wire must be solder between two pds. You need fine solder iron nd short piece of insulted thin wire nd mybe little piece of tin. Don t use ny soldering brid or pumps they my dmge the pcb. - Remove the resistor by heting the ends of the resistor, lternte from left to right end stying few seconds t ech end until the component come loose. B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 07 of 9

108 - Solder the thin insulted wire between the solder pds s shown on the picture below. Power supply Control-RRC: The Control-RRC is supplied with common 3, V (0-V) power supply. The disply nd speker mplifier needs lot of power so you need A. B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 0 of 9

109 Rdio-RRC: The Rdio-RRC should be supplied from the sme power supply s the rdio to void humming. Plese put smll fuse on the cble if you connect it to 30 Amp PS. B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 09 of 9

110 PWR ON GND GND RD TD V Control Pnel IC-E0 -pol Modulr RRC-5MkII TTL pol Modulr Con White Blck Blck Blue 3 Red Red 3 4 Green Yellow 4 5 Yellow Green 5 Blue White I0b : ICOM cble RRC-5MkII to ID-E0 Pnel end SPEAKER 3.5 mm stereo plug 5 Cble I0 () USER MANUAL B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 0 of 9

111 SPEAKER 3.5 mm stereo plug RRC-5MkII / pol Modulr Con 3 4 Blck Control Inp ID-E0 / pol Modulr Con White Blck Red 3 Green White Blue I9b I9c : ICOM cble RRC-5 to ICOM ID-E0 Rdio end PWR ON GND GND RD TD V 5 Cble I9 () SPEAKER 3.5 mm stereo plug USER MANUAL MIC MIC 7 7 Green Yellow RRC-5MkII -pol RJ 45 Con Blue Red Yellow Try Stndrd shielded CAT 5 PTT PTT I9 Mic Inp ID-E0 MICE MICE GND GND -pol RJ 45 Con B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 of 9

112 ICOM IC-75 Generl It's not only shortwve trnsceivers which could be remote controlled, the remoterig system lso support ICOM:s IC-75. The technicl solution is the sme s for IC-70 nd TS-40; you cn remote control the rdio over Internet from the control pnel without ny PC. We simply replce the cble between the control pnel nd the rdio with two RRC-5 units, one t the control pnel nd one t the rdio. When you push the PWR-ON button n udio nd dt connection is estblished between the units nd you control the rdio s you do normlly with the control pnel directly ttched to the rdio. There re no limittions in functionlity, everything works nd you cn use the originl microphone. Hrdwre configurtion Unfortuntely ICOM hve inverted the seril bus in the IC-75 so there need hrdwre dption to mke it work. This is quite simple so it cn be done by yourself. The dpters cn lso be bought from Remoterig webshop. The dpters re connected to the strpping socket where the red jumpers re normlly connected. The trnsistors used on the PCB hve built in resistors, so if you use stndrd trnsistor like BC-547 nd BC-557 you hve to put the resistors outside. Check the dt sheets for PDTC-43ET nd PDTA-44ET. Control side B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 of 9

113 Rdio side Microbit Adpters 5L When ssembling the dpter pcb:s tke notice tht they re not the sme in the different units, one is mrked Control nd the other Rdio. Be sure to put them in the right RRC nd tht they re turned ccording to the picture below. B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 3 of 9

114 Rdio settings (exmple) Prmeter Control Rdio Progrm mode 7 ICR500/IC-75 7 ICR500/IC-75 SIP pssword hello hello SIP relm SIP contct Auto connect No Audio qulity Liner bits khz Liner bits khz Audio dul-rx (*) No/Yes Codec out gin Codec inp gin 0 Codec inp premp Yes Codec inp HPF Hz 3 3 COM0 budrte COM0 dt bits COM0 stop bits COM0 prity 0 - Off 0 - Off (*) Avilble only in RRC-5MkIIs, remember tht the bndwidth demnd is doubled. Connections The cbling is quite simple nd cn be done with simple RJ connectors. Power supply Control-RRC: The Control-RRC is supplied with common 3, V (0-V) power supply. The disply nd speker mplifier needs lot of power so you need A. Rdio-RRC: The Rdio-RRC should be supplied from the sme power supply s the rdio to void humming. Plese put smll fuse on the cble if you connect it to 30 Amp PS. B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 4 of 9

115 Control Pnel IC-75 -pol Modulr : ICOM cble RRC-5MkII to IC-75 Pnel end RRC-5MkII MIC/AUX pol Modulr Con HV DATA DATA MICE MIC GND SPEAKER 3.5 mm stereo plug 5 Cble I () USER MANUAL B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 5 of 9

116 4 SPEAKER 3.5 mm stereo plug RRC-5MkII MIC/AUX pol Modulr Con HV DATA DATA MICE MIC GND Control Inp IC-75 pol Modulr Con : ICOM cble RRC-5MkII to IC-75 Rdio end Cble I7 () SPEAKER 3.5 mm stereo plug B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 of 9

117 YAESU FT-x7, FT-000 Generl RRC-5MkII supports the YAESU CAT protocol used by lmost every YAESU rdio. Then you hve to use PC-softwre e.g. HmRdioDeLuxe or similr rig control softwre t the control site. All udio nd dt communiction goes true the RRC:s nd you don't need PC t the remote site. Hrdwre configurtion B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 7 of 9

118 Rdio settings (exmple) Prmeter Control Rdio Progrm mode 3 FT-x7, FT-000x 3 FT-x7, FT-000x SIP pssword hello hello SIP relm SIP contct Auto connect No Audio qulity Liner bits khz Liner bits khz Audio dul-rx * No/Yes (ev. for FT-000xx) Codec out gin Codec inp gin 0 Codec inp premp Yes Codec inp HPF Hz 3 3 COM0 budrte COM0 dt bits COM0 stop bits ** ** COM0 prity 0 - Off 0 - Off (*) Avilble only in RRC-5MkIIs, remember tht the bndwidth demnd is doubled. (**) check with the rdio users mnul, some model need stopbits. Connections Drwings of the connection cbles cn be found under ppendix B. Control-RRC: Connect the Remoterig Y5c cble or stndrd RS-3 cble between the PC nd the RRC COM. The microphone cn be connected direct to the RRC AUX/MIC connector if you hve microphone with RJ-45 connector. If you hve microphone with circulr connector you cn use the Remoterig Y5 dpter cble or the ADMY-7, from Yesu or mke one by yourself. The speker is connected direct to the RRC SP-jck with 3.5 mm stereo plug. Rdio-RRC: From the RRC COM connector to the rdios CAT connector (D-sub RS-3) you cn use the Remoterig Yc cble or mke one by yourself (drwing for Yc is provided). The smller rdios in the FT-x7 series do not hve D-sub or RS-3 port; they only hve TTL-port ccessible vi mini-din jck. You cn either buy n dpter cble, D-sub to mini-din, with level converter clled CT- from Yesu or you cn mke cble by yourself nd connect it to the RRC TTL connector. Between the RRC AUX/MIC connector nd the rdios microphone jck you cn connect stndrd ptch cble if the rdio hve RJ-45 jck. If the rdio hve circulr microphone jck you cn use the Remoterig Y cble or mke it by yourself (drwings re provided). Mke the cble s short s possible to prevent it from picking up HF. B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 of 9

119 The speker signl from the rdios externl speker jck to the RRC SP jck is connected vi stndrd "off- the-shelf cble with 3.5 mm stereo plugs in both ends. Y5,Y Y5c,Yc B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 9 of 9

120 Front pnel view Mic Inp -pol Circulr 5 7 GND PTT MIC MICE Y5 screened 0 cm Y5b : Generic YAESU Cble RRC-5MkII to Yesu (FT-000) RRC-5MkII -pol RJ 45 Con GND PTT MIC MICE V UP RRC-5MkII 7 5 Cble Y5 () SPEAKER 3.5 mm stereo plug USER MANUAL PC DSUB- 9pol Femle Y5c COM DSUB- 9pol Mle B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 0 of 9

121 RRC-5MkII COM DSUB- 9pol Femle Yc PWR ON indiction : Generic YAESU cble RRC-5MkII -> Rdio GND GND Rdio CAT port DSUB- 9pol Femle GND 5 Cble Y () USER MANUAL -pol RJ 45 Con Mic Inp -pol Circulr MIC MIC PTT PTT SPEAKER 3.5 mm stereo plug RRC-5MkII V MICE Y screened m Yb V MICE 7 5 Front pnel view SPEAKER 3.5 mm stereo plug B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 of 9

122 SPEAKER 3.5 mm stereo plug RRC-5MkII AUX/MIC Try Stndrd shielded CAT 5 MIC MICE MICE MIC MIC PTT PTT GND GND Mini-DIN FT-7,57,97 : YAESU x7 cble RRC-5MkII -> Rdio FT-7,57,97 -pol RJ 45 Con 4 5 RX D TX D 5 Cble Y7 () SPEAKER 3.5 mm stereo plug USER MANUAL 7 7 GND GND 3 3 RRC-5MkII TTL -pol modulr GND V RXD TXD AF 3 B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 of 9

123 YAESU Generl (FT-000) Generl RRC-5MkII supports the YAESU CAT protocol used by lmost every YAESU rdio. Then you hve to use PC-softwre e.g. HmRdioDeLuxe or similr rig control softwre t the control site. All udio nd dt communiction goes true the RRC:s nd you don't need PC t the remote site. Hrdwre configurtion B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 3 of 9

124 Rdio settings (exmple) Prmeter Control Rdio Progrm mode 4 Yesu, Kenwood, Elecrft 4 Yesu, Kenwood, Elecrft SIP pssword hello hello SIP relm SIP contct Auto connect No Audio qulity Liner bits khz Liner bits khz Audio Dul-RX (*) - Yes Codec out gin Codec inp gin 0 Codec inp premp Yes Codec inp HPF Hz 3 3 COM0 budrte COM0 dt bits COM0 stop bits COM0 prity 0 Off 0 Off (*) Avilble only in RRC-5MkIIs, remember tht the bndwidth demnd is doubled. Connections Drwings of the connection cbles cn be found below. Control-RRC: Connect the Remoterig Y5c or stndrd RS-3 cble between the PC nd the RRC COM. The microphone cn be connected direct to the RRC AUX/MIC connector if you hve microphone with RJ-45 connector. If you hve microphone with circulr connector you cn use the Remotrig Y5 cble, the ADMY-7, from Yesu or mke one by yourself. The speker is connected direct to the RRC SP-jck with 3.5 mm stereo plug. Rdio-RRC: From the RRCCOM connector to the rdios CAT connector (D-sub RS-3) you cn use the Remoterig Yc cble or mke cble by yourself (drwings re provided). The smller rdios in the FT-x7 series do not hve D-sub or RS-3 port; they only hve TTL-port ccessible vi mini-din jck. You cn either buy n dpter cble, D-sub to mini-din, with level converter clled CT- from Yesu or you cn mke cble by yourself nd connect it to the RRC TTL connector. Between the RRC AUX/MIC connector nd the rdios microphone jck you cn connect stndrd ptch cble if the rdio hve RJ-45 jck. If the rdio hve circulr microphone jck you cn use the Remoterig Y cble or mke n dpter cble by yourself (drwings re provided). If you mke the cble by yourself, just cut stndrd B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 4 of 9

125 FTP (screened) ptch cble nd solder n -pin circulr connector on it. Mke the cble s short s possible to prevent it from picking up HF. The speker signl from the rdios externl speker jck to the RRC SP jck is connected vi stndrd off- the-shelf cble with 3.5 mm stereo plugs in both ends. Y5,Y Y5c,Yc B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 5 of 9

126 Front pnel view Mic Inp -pol Circulr 5 7 GND PTT MIC MICE Y5 screened 0 cm Y5b : Generic YAESU Cble RRC-5MkII to Yesu (FT-000) RRC-5MkII -pol RJ 45 Con GND PTT MIC MICE V UP RRC-5MkII 7 5 Cble Y5 () SPEAKER 3.5 mm stereo plug USER MANUAL PC DSUB- 9pol Femle Y5c COM DSUB- 9pol Mle B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 of 9

127 RRC-5MkII COM DSUB- 9pol Femle Yc PWR ON indiction : Generic YAESU cble RRC-5MkII -> Rdio GND GND Rdio CAT port DSUB- 9pol Femle GND 5 Cble Y () USER MANUAL -pol RJ 45 Con Mic Inp -pol Circulr MIC MIC PTT PTT SPEAKER 3.5 mm stereo plug RRC-5MkII V MICE Y screened m Yb V MICE 7 5 Front pnel view SPEAKER 3.5 mm stereo plug B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 7 of 9

128 YAESU TWIN Generl RRC-5MkIIs Yesu Twin supports the specil high end concept where one Yesu rdio cn be used to control nother Yesu rdio. No PC:s needed t either end. The RRC-5MkIIs Yesu Twin pckge includes power supplys nd ll necessry cbles. The boxes do not need to be opened ll strppings re done in production. All you need to do is to put the system together nd do the IP-settings. The twin concept is minly developed for using with two rdios of the sme model for exmple two FT-5000, but two different models cn lso be used. The following combintions of re tested: Control FT-950 FT-000 FT-5000 FT-950 FT-000 FT-9000 FT-9000 Rdio FT-950 FT-000 FT-5000 FT-5000 FT-5000 FT-5000 FT-9000 In the combintions tested bove ll functions works nd re tested by severl test pilots, nywy we cnnot give ny gurnties tht we hve not missed some minor function. The meter functions in the FT-950 hve some limittions, the PWR, SWR nd ALC re replicted to the controlling rdio but there is no scle mrks on the meters so you hve to lern how the B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 of 9

129 different vlues re represented. For the FT-9000 FT-9000 the sub RX must be ctive for the ALC meter to work, nd of course the spectrum scope does not work remotely. Attention! If you wnt to use the Auto tuner on the Remote rdio, it s very importnt tht you connect dummy lods to the corresponding ntenn ports on the control rdio. As the rdio do not use full power when tuning nd it s done reltively fst, smll nd chep 0-0W dummylods cn be used (not included). Hrdwre configurtion In the stndrd RRC:s the strppings re done mnully by the customer, but In the RRC- 5MkIIs Yesu Twin pckge the strppings re done by smll pcb mrked 5Y which is ssembled t the strpping re. The smll pcb is removble if you lter wnt to use the RRC:s for some other configurtion. When you replce it is importnt tht the notch which mrks pin one is plced ccording to the picture below. For your reference the picture below shows how the strppings re done on the smll pcb. B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 9 of 9

130 B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 30 of 9

131 Rdio settings (exmple) Prmeter Control Rdio Progrm mode 0 Yesu FT- 950/000/5000/9000 twin 0 Yesu FT- 950/000/5000/9000 twin SIP pssword hello hello SIP relm SIP contct Auto connect No Audio qulity Liner bits khz Liner bits khz Audio Dul-RX - Yes (*) Codec out gin Codec inp gin 0 Codec inp premp Yes Codec inp HPF Hz 3 3 COM0 budrte 3400(*) 3400(*) COM0 dt bits COM0 stop bits COM0 prity 0 Off 0 Off (*) Remember tht the bndwidth demnd is doubled if Dul-RX is ctivted. (*) Set the CAT speed in both Rdios lso to 3400 bud. B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 3 of 9

132 Connections Drwings of the connection cbles cn be found below. All necessry cbles re included in the pckge. Control site Connect V power supply to the PWR jck Connecter Ethernet to the Ethernet jck ( m CAT 5 cble included) 3 Connect the CAT cble Y5d from the COM connector to the rdio CAT connector 4 Connect the microphone vi the Microphone dpter cble Y5 5 Connect speker to the speker jck (spekers nd cble re not included) Connect pddle to the PAD jck ( dpter from ¼ connector to 3.55 mm included) 7 Connect dummy to the hedset jck on the trnsceiver to quiet the Internl speker. Connect Dummy lods to the Antenn jcks (not included) B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 3 of 9

133 Rdio site Connect V power supply to the PWR jck Connecter Ethernet to the Ethernet jck ( m CAT 5 cble included) 3 Connect the CAT cble Yd from the COM connector to the rdio CAT connector 4 Connect the mic cble Y from the AUX/MIC jck to the rdio mic connector. 5 Connect the udio cble from to the SP jck to the rdio hedphone output. (Adpter from ¼ connector to 3.5 mm included) Connect the keying cble from the PAD jck to the rdio key input (Adpter from ¼ connector to 3.55 mm included) B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 33 of 9

134 Logging or computer control, RTTY etc. Even if the CAT connector t the Remote Rdio is occupied with the communiction between the two Rdios it is possible to connect other equipment to the system due to n intelligent CAT server functionlity in the RRC.s. If you need to connect ntenn switch for exmple which need to tlk to the remote Rdio you cn connect it to the Rdio-RRC COM nd configure COM to Mode, CAT to COM (locl). If you wnt to connect logging or PC-control softwre to the system you cn connect it to the Control-RRC COM vi RS-3 or USB nd configure both RRC:s COM to Mode-, CAT to COM (locl). You cn still use the remote ntenn switch s described bove. Independent of the connections bove you cn use the Remote Rdios FSK trnsmission. Configure Rdio-RRC OUT mode = Budot/45 nd use the Virtul USB port COMFSK for the RTTY softwre. B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 34 of 9

135 Cble Y5d Control Rdio to Control-RRC COM Cble Yd Rdio-RRC to Remote Rdio COM Cble Y5 Mic to Control-RRC Mic jck Cble Y Rdio-RRC Mic jck to Rdio Mic input Cble 3.5 mm 3.5 mm Audio Output from Remote rdio to Rdio-RRC SP input jck Cble 3.5 mm ¼ Keyer from Rdio-RRC PAD jck to Remote rdio stright key input jck B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 35 of 9

136 Adpter ¼ to 3.5 mm Hedset dpter Adpter ¼ to 3.5 mm Pddle dpter Adpter 3.5 mm to ¼ Hedset output dpter from remote remote rdio Control-RRC: Connect the RS-3 cble Y5d between the Control-RRC COM nd the CAT connector on the Rdio. The microphone cn be connected direct to the RRC AUX/MIC connector if you hve microphone with RJ-45 connector. If you hve microphone with circulr connector use the dpter cble Y5. The speker is connected direct to the RRC SP-jck with 3.5 mm stereo plug. Pddles re connected to the PAD jck. If you the pddles hve ¼ plug on your pddle use the supplied ¼ to 3.5 mm dpter cble. Connect the CAT 5 cble from the Ethernet jck to your switch or router Connect the V power supply to the DC jck Rdio-RRC: Connect the RS-3 cble Yd from the Rdio-RRC COM connector to the rdios CAT connector. B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 3 of 9

137 Connect the mic cble Y from the Rdio-RRC AUX/MIC connector to the rdios microphone jck. Connect the speker signl from the rdios hedset output jck or similr to the Rdio- RRC SP jck with the stndrd 3.5 mm 3.5 mm cble with stereo plugs in both ends. If the rdio hve ¼ jck use the supplied dpter ¼ to 3.5mm. Connect keyer cble (stndrd 3.5 mm 3.5 mm cble with stereo plugs in both ends) from the Rdio-RRC PAD jck to the stright key input jck on the Rdio. If the rdio hve ¼ jck, use the supplied 3.5 mm to ¼ dpter. Connect the CAT 5 cble from the Ethernet jck to your switch or router Connect the V power supply to the DC jck B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 37 of 9

138 FT-950/000/5000/9000 CAT port : YAESU TWIN Cbles RRC-5MkII to Rdio (twin Control side) RRC-5MkII 5 Cble Y5 () USER MANUAL Front pnel view Mic Inp -pol Circulr GND PTT MIC MICE Y5d DSUB- 9pol Femle Sme s Yesu ADMY-7 Y5 RRC-5MkII -pol RJ 45 Con GND PTT MIC MICE DSUB- 9pol Mle COM 5 B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 3 of 9

139 7 Rdio CAT port 3 5 DSUB- 9pol Femle 7 : YAESU TWIN cbles RRC-5MkII -> Rdio (twin rdio side) GND 5 Cble Y () USER MANUAL PTT PTT SPEAKER 3.5 mm stereo plug RRC-5MkII 3 5 -pol RJ 45 Con MICE DSUB- 9pol Femle MIC MIC GND GND RRC-5MkII COM Y Yb Mic Inp -pol Circulr MICE 7 5 Front pnel view SPEAKER 3.5 mm stereo plug B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 39 of 9

140 KENWOOD Generl Generl RRC-5MkII supports the Kenwood protocol used by lmost every Kenwood rdio. Then you hve to use PC-softwre e.g. HmRdioDeLuxe or similr rig control softwre t the control site. All udio nd dt communiction goes true the RRC:s nd you don t need PC t the remote site. Hrdwre configurtion B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 40 of 9

141 SIP-Connect/disconnect vi MIC UP button: Rdio settings (exmple) Prmeter Control Rdio Progrm mode 4 Yesu, Kenwood, Elecrft 4 Yesu, Kenwood, Elecrft SIP pssword hello hello SIP relm SIP contct Auto connect No Audio qulity Liner bits khz Liner bits khz Audio dul-rx (*) No Codec out gin Codec inp gin 3 0 Codec inp premp Yes Codec inp HPF Hz 3 3 COM0 budrte COM0 dt bits COM0 stop bits 0 - Off 0 - Off COM0 prity *) Avilble only in RRC-5MkIIs. Connections Drwings of the connection cbles cn be found under ppendix B. Control-RRC: B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 4 of 9

142 Connect the Remoterig K4c Cble or stndrd RS-3 cble between the PC nd the RRC COM. The microphone cn be connected direct to the RRC AUX/MIC connector if you hve microphone with RJ-45 connector. If you hve microphone with circulr connector you cn use the Remoterig K3 cble, the MJ-, from Kenwood or mke one by yourself (drwings re provided). The speker is connected direct to the RRC SP-jck with 3.5 mm stereo plug. Rdio-RRC: From the RRC COM connector to the rdios CAT connector (D-sub RS-3) you use the Remoterig K5c cble or mke one by yourself (drwings re provided). Between the RRC AUX/MIC connector nd the rdios microphone jck you cn connect stndrd ptch cble if the rdio hve RJ-45 jck. If the rdio hve circulr microphone jck you cn use the Remoterig K cble or mke one by yourself (drwings re provided).mke the cble s short s possible to prevent it from picking up HF. The speker signl from the rdios externl speker jck to the RRC SP jck is connected vi stndrd "off- the-shelf cble with 3.5 mm stereo plugs in both ends. K4,K5 K4c,K5c B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 4 of 9

143 Front pnel view Mic Inp -pol Circulr GND K4 screened 0 cm K4b : Generic Kenwood cble Control -> RRC-5MkII RRC-5MkII -pol RJ 45 Con GND 5 Cble K4 () SPEAKER 3.5 mm stereo plug USER MANUAL UP UP V V PC 7 PTT MICE MIC PTT MICE MIC 7 RRC-5MkII COM DSUB- 9pol K4c Femle DSUB- 9pol Mle B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 43 of 9

144 SPEAKER 3.5 mm stereo plug RRC-5MkII -pol RJ 45 Con MIC MICE PTT GND V RRC-5MkII COM DSUB- 9pol Femle K5c K5b PWR ON indiction K5 screened m Rdio CAT port 3 5 DSUB- 9pol Femle 7 : Generic Kenwood cble RRC-5MkII -> Rdio GND Mic Inp -pol Circulr MIC MICE PTT GND V Cble K5 () Front pnel view SPEAKER 3.5 mm stereo plug USER MANUAL B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 44 of 9

145 B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 45 of 9

146 KENWOOD TS-40 Generl The ide of remote controlling TS-40 is simple; it's just to extend the cord between the rdio nd the control pnel using Internet. When you press the power button on the pnel the rdio comes to life t the remote side nd sound nd pnel info flows cross the Internet between the pir of RRC-5MkII:s. The look nd feel of the pnel is the sme s if the pnel ws directly connected to the rdio. Hrdwre configurtion To mke things little bit more complicted Kenwood hve chnged the lyout of the Mic connector during production nd there re two different configurtions. New rdios with seril number from re using Configurtion type nd older rdios with seril number below re using configurtion type. Configurtion type : Configurtion type : B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 4 of 9

147 Rdio settings (exmple) Prmeter Control Rdio Progrm mode 5 TS40/TM-D70 5 TS40/TM-D70 SIP pssword hello hello SIP relm SIP contct Auto connect No Audio qulity Liner bits khz Liner bits khz Audio dul-rx (*) No Codec out gin Codec inp gin 3 0 Codec inp premp Yes Codec HPF Hz 3 3 COM0 budrte COM0 dt bits COM0 stop bits COM0 prity 0 - Off 0 - Off *) Avilble only in RRC-5MkIIs. Connections All necessry signls between the pnel nd the rdio re connected with the wires in the connection cble. We just need to cut it prt nd connect RRC-5MkII in ech end. Convenient for trvelling is tht the speker is lredy present on the bck of the control pnel so there is no need for n extr speker, even if seprte speker gives much better udio. The following signls re represented in the connection cble (-pol modulr): SPK GND - speker ground V power to control pnel (lwys present) 3 GND 4 RDO - seril dt 5700 bps from rdio to pnel B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 47 of 9

148 5 TDO - seril dt 5700 bps from pnel to rdio AF - udio to speker. The esiest wy to mke these two cbles from Control pnel to Control-RRC TTL connector nd from Rdio-RRC TTL connector to rdio is to cut the cble supplied by Kenwood into two pieces. You only hve to crimp two new / modulr connectors on the cbles. Don't mke the one between Rdio-RRC nd rdio to long. The long Microphone extension cble supplied by Kenwood cn lso be used between Rdio- RRC AUX/MIC connector to the rdio Microphone jck. Probbly you need to cut it lter to prevent it from picking up HF from your ntenns. If the TS-40 is provided with microphone with RJ-45 connector you cn connect it directly to the AUX/MIC connector on the Control-RRC. If it's provided with circulr pin connector you cn used the dpter cble MJ- supplied by Kenwood with your TS-40 s dpter between the Microphone nd the AUX/MIC connector. Connection type Modulr -pol connector: 3 MIC- mic Signl 4 MICE - mic ground 5 PTT GND PTT Connection type Modulr -pol connector: 3 MIC- mic Signl 4 GND PTT 5 PTT MICE - mic ground If you use the wrong configurtion everything will work but the system will be very sensitive for HF (RFI). Power supply Control-RRC: The Control-RRC is supplied with common 3, V (0-V) power supply. The disply nd speker mplifier needs lot of power so you need t lest A. Rdio-RRC: The Rdio-RRC could be powered with seprte Power supply or the sme s the rdio. If you use the Rdio PS mke sure you hve A fuse on the output to the RRC. Do not connect it direct to 0-40A PS the cble will melt if something hppens. B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 4 of 9

149 GND DET NR. CNT NAME DIMENSION NOTE CONSTR. DRAWN COPIED CHECKED STAND. OK SCALE REPLACE REPLACED BY MS : Kenwood cbles TS-40 Pnel -> RRC-5MkII Seprted Pnel -pol modulr -pol modulr GND GND V V GND GND GND 093 DRAWING NR DATE Cble K () USER MANUAL AF AF Front pnel view Mic Inp -pol Circulr 7 TS-40 Control Pnel PTT MICE MIC Sme s Kenwood MJ- K RRC-5MkII -pol RJ 45 Con MICE RRC 5MkII TTL RDO RDO TDO TDO Kb PTT MIC B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 49 of 9

150 RRC-5MkII AUX/MIC RRC-5MkII TTL : Kenwood cbles RRC-5MkII -> TS-40 Rdio Seprted Pnel Mic Inp TS-40 Control Inp TS-40 5 Cble K0 () USER MANUAL 3 MIC MIC () () PTT PTT 5 5 GND GND 7 7 AF AF -pol RJ 45 Con -pol modulr MICE GND GND MICE () () () () MICE Try Stndrd shielded CAT 5 () () () () () () () () For Mic config type (s/n > ) For Mic config type (s/n < ) MICE GND GND V V GND GND RDO RDO TDO TDO -pol RJ 45 Con -pol modulr B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 50 of 9

151 KENWOOD TM-D70 Generl The Kenwood TM-D70 is modern dul bnd FM-trnsceiver with seprte control pnel which is perfect for remote control vi Internet. The ide of remote controlling TM-D70 is simple; it's just to extend the cord between the rdio nd the control pnel using Internet. When you press the power button on the pnel the rdio comes to life t the remote side nd sound nd pnel info flows cross the Internet between the pir of RRC-5MkII:s. The look nd feel of the pnel is the sme s if the pnel ws directly connected to the rdio. Hrdwre configurtion It's very simple to Interfce the TM-D70 for remote control vi the RRC:s. You only need to mke two simple cbles. One from the Control pnel to the Control-RRC nd one from the Rdio-RRC to the Rdio. The stndrd mic (MC-59) provided with the TM-D70 cn be used nd connected directly to the Control-RRC. From Rdio-RRC to Rdio stndrd CAT-5 cble cn be used for the Mic-signls. A stndrd udio cble with /" inch connectors re used for the udio. A speker re lso needed s there is no speker in the Control pnel. All softwre settings re the sme s for TS-40, but the strps re little bit different in the Control-RRC s the MC-59 mic needs V DC feeding. (see drwings below). Remember tht the buttons on the microphone will not work. If you need DTMF use n other Mic with built in DTMF encoder. The MC-59 do not hve it. It's lso possible to progrm DTMF functions to the rdio which will vilble from the Control pnel. All other functions works s in the norml setup. B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 5 of 9

152 Kenwood TM-D70 Rdio settings (exmple) Prmeter Control Rdio Progrm mode 5 TS40/TM-D70 5 TS40/TM-D70 SIP pssword hello hello SIP relm SIP contct Auto connect No Audio qulity Liner bits khz Liner bits khz Audio dul-rx (*) No Codec out gin Codec inp gin 3 0 Codec inp premp Yes Codec HPF Hz 3 3 COM0 budrte COM0 dt bits COM0 stop bits COM0 prity 0 - Off 0 - Off *) Avilble only in RRC-5MkIIs. Power supply Control-RRC: The Control-RRC is supplied with common 3, V (0-V) power supply. The disply nd speker mplifier needs lot of power so you need t lest A. Rdio-RRC: The Rdio-RRC could be powered with seprte Power supply or the sme s the rdio. If you use the Rdio PS mke sure you hve A fuse on the output to the RRC. Do not connect it direct to 0-40A PS the cble will melt if something hppens. B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 5 of 9

153 : Kenwood TM-D70 cbles Control => RRC-5MkII SPEAKER 3.5 mm stereo plug 5 Cble K7 () USER MANUAL Control Pnel TM-D70 RRC-5MkII TTL -pol RJ 45 Con V GND TXD RXD K7 4/-pol modulr B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 53 of 9

154 RRC-5MkII AUX/MIC RRC-5MkII TTL 4/-pol modulr Kc K : Kenwood TM-D70 cbles RRC-5MkII -> Rdio Mic Inp TM-D70 Control Inp TM-D70 Rdio 0V GND TXD RXD Cble K () USER MANUAL SPEAKER 3.5 mm stereo plug -pol RJ 45 Con Try Stndrd shielded CAT 5 MIC MIC MICE MICE PTT PTT GND GND Kb -pol RJ 45 Con -pol RJ 45 Con SPEAKER 3.5 mm stereo plug B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 54 of 9

155 KENWOOD TS-000 Generl The technicl solution for TS-000 is the sme s for TS-40 nd IC-70 with the different tht TS-000 hs specil control pnel witch works in prllel with the front pnel control on the rdio. If you hve the TS-000 t your summer QTH you do not need to tke the control pnel with you when you wnt to use the TS-000 loclly. We replce the cble between pnel nd rdio with to RRC-5, one connected to the control pnel nd one connected to the rdio. When you press the power button on the pnel the rdio comes to life t the remote side nd udio nd pnel info flows cross the internet between the RRC:s. The look nd feel of the control pnel is the sme s if the pnel ws directly connected to the rdio. Hrdwre configurtion B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 55 of 9

156 Rdio settings (exmple) Prmeter Control Rdio Progrm mode TS000 TS000 SIP pssword hello hello SIP relm SIP contct Auto connect No Audio qulity Liner bits khz Liner bits khz Audio dul-rx (*) - Yes Codec out gin Codec inp gin 3 0 Codec inp premp Yes Codec inp HPF Hz 3 3 COM0 budrte COM0 dt bits COM0 stop bits COM0 prity 0 - Off 0 - Off (*) Avilble only in RRC-5MkIIs, remember tht the bndwidth demnd is doubled. Connections The TS-000 is quite simple to connect becuse you do not need ny specil cble. All necessry signls between the pnel nd the rdio re connected with the 4 wires in the connection cble. We just need to cut it prt nd connect RRC-5MkII in ech end. The following signls re represented in the connection cble (modulr): RJ Modulr 4/ Rdio RJxx Modulr 4/4 Control pnel Description V power to control pnel (lwys present) 3 GND 4 3 RDO - seril dt 5700 bps from rdio to pnel 5 4 TDO - seril dt 5700 bps from pnel to rdio The esiest wy to mke these two cbles from control pnel to Control-RRC TTL connector nd from Rdio-RRC TTL connector to rdio is to cut the cble supplied by Kenwood into two pieces. You only hve to crimp two new 4/ modulr connectors on the cbles. Don't mke the one between Rdio-RRC nd rdio to long. The long microphone extension cble supplied by Kenwood cn lso be used between Rdio- RRC AUX/MIC connector to the rdio Microphone jck. Probbly you need to cut it lter to prevent it from picking up HF from your ntenns. B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 5 of 9

157 The microphone cn be connected to the Control-RRC AUX/MIC connector using the dpter cble MJ- supplied by Kenwood with your TS-000. The speker supplied with the TS-000 is connected to the 3.5 mm SP-jck on the front of the Control-RRC. The speker signl from the TS-000 ext. speker jck to the Rdio-RRC SP jck is connected vi stndrd "off-the-shelf cble with 3.5 mm stereo plugs in both ends. B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 57 of 9

158 4 RC-000 Control Pnel 4-pol Modulr 4/4 DET NR. CNT NAME DIMENSION NOTE CONSTR. DRAWN COPIED CHECKED STAND. OK SCALE REPLACE REPLACED BY MS : Kenwood cble RC-000 -> RRC-5MkII RC000 Pnel 093 DRAWING NR DATE Cble K3 () USER MANUAL GND GND 3 4 Front pnel view Mic Inp -pol Circulr 7 4 GND PTT MICE MIC Sme s Kenwood MJ- K3 K3b V K3c V RDO RDO TDO TDO RRC-5MkII -pol RJ 45 Con RRC-5MkII TTL 4/-pol modulr 3 5 GND PTT MICE MIC SPEAKER 3.5 mm stereo plug B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 5 of 9

159 SPEAKER 3.5 mm stereo plug RRC-5MkII -pol RJ 45 Con MIC MICE PTT RRC-5MkII TTL 4/-pol modulr GND GND K Kb V V 3 GND GND 3 4 RDO RDO 4 5 TDO TDO Kc 5 : Kenwood cble RRC-5MkII -> TS-000 RC-000 Pnel Control Inp TS-40 4/-pol modulr Mic Inp -pol Circulr MIC MICE PTT 7 Front pnel view Cble K () 7 5 SPEAKER 3.5 mm stereo plug USER MANUAL B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 59 of 9

160 ELECRAFT K3-Twin RRC-5MkIIs supports the specil high end concept where one Elecrft K3 rdio cn be used to control nother Elecrft K3 rdio. No PC:s needed t either end. The functionlity is perfect s Elecrft hs dded support in their softwre specilly for this purpose. The control rdio is not used other thn s terminl so it doesn t mtter how it s configured. It cn be the simplest K3/0 without ny options even if the remote K3 is loded with ll extrs. The RRC-5MkIIs Elecrft Twin pckge includes power supplies nd ll necessry cbles. The boxes do not need to be opened ll strppings re done in production. All you need to do is to put the system together nd do the IP-settings. The ordinry RRC-5MKIIs cn lso be configured to be used for Elecrft K3 twin. Hrdwre configurtion In the stndrd RRC:s the strppings re done mnully by the customer, but In the RRC- 5MkIIs Elecrft K3 Twin pckge the strppings re done by smll pcb mrked 5KE which is ssembled t the strpping re. The smll pcb is removble if you lter wnt to use the RRC:s for some other configurtion. When you replce it is importnt tht the notch which mrks pin one is plced ccording to the picture below. B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 0 of 9

161 For your reference the picture below shows how the strppings re done on the smll pcb. JMP should be in plce when using Elecrft MH Mic nd removed when using for exmple Heil hedset. Rdio settings (exmple) Prmeter Control Rdio Progrm mode 4 Elecrft K3 twin 4 Elecrft K3 twin SIP pssword hello hello SIP relm SIP contct Auto connect No Audio qulity Liner bits khz Liner bits khz Audio Dul-RX - Yes/No (*) Codec out gin Codec inp gin 4 0 Codec inp premp Yes B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 of 9

162 Codec inp HPF Hz 3 3 COM0 budrte 3400 (*) 3400 (*) COM0 dt bits COM0 stop bits COM0 prity 0 - Off 0 - Off COM mode Logicl prllel with COM0 Logicl prllel with COM0 (*) Avilble only in RRC-5MkIIs, remember tht the bndwidth demnd is doubled. (*) Set the CAT speed in both Rdios lso to 3400 bud. Connections Connections Drwings of the connection cbles cn be found below. All necessry cbles re included in the pckge. Control site B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 of 9

163 Connect V power supply to the PWR jck Connecter Ethernet to the Ethernet jck ( m CAT 5 cble included) 3 Connect the CAT cble Ed from the RRC COM connector to the K3 CAT connector 4 Connect the microphone vi the Microphone dpter cble E 5 Connect speker to the speker jck, If you wnt seprte udio from the sub-rx you need two spekers, the speker for the sub-rx must be ctive. (spekers nd cble re not included) Connect pddle to the PAD jck ( dpter from ¼ connector to 3.5 mm included) Rdio site B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 3 of 9

164 Connect V power supply to the PWR jck Connecter Ethernet to the Ethernet jck ( m CAT 5 cble included) 3 Connect the CAT cble Ec from the COM connector to the K3 CAT connector 4 Connect the mic cble E from the AUX/MIC jck to the K3 mic connector. 5 Connect the udio cble from to the SP jck to the K3 speker out on the bck output. Connect the keying cble from the PAD jck to the K3 key input (Adpter from ¼ connector to 3.55 mm included) 7 Connect the K3 remote power on cble E3c from I/O jck to the K3 ACC connector. B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 4 of 9

165 Logging or computer control, RTTY etc. Even if the CAT connector t the Remote K3 is occupied with the communiction between the two K3:s it is possible to connect other equipment to the system due to n intelligent CAT server functionlity in the RRC.s. If you need to connect ntenn switch for exmple which need to tlk to the remote K3 you cn connect it to the Rdio-RRC COM nd configure COM to Mode, CAT to COM (locl). If you wnt to connect logging or PC-control softwre to the system you cn connect it to the Control-RRC COM vi RS-3 or USB nd configure both RRC:s COM to Mode-7, CAT to COM (locl&remote). Then ll commnds go to nd from the Remote K3 over the network. You cn still use the remote ntenn switch s described bove. Independent of the connections bove you cn use the K3:s FSK trnsmission. Configure Rdio-RRC OUT mode = Budot/45 nd use the Virtul USB port COMFSK for the RTTY softwre. The supplied ACC cble re wired to key the K3 FSK input. B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 5 of 9

166 Cble Ed Control K3 to Control-RRC COM 9PF-9PF Cble Ec Rdio-RRC COM to Remote K3 9PM-9PF Cble E3c I/O to K3 ACC jck Adpter 3.5 mm to ¼ Pddle input dpter to remote rdio Cble E Mic to Control-RRC Mic jck Cble E Rdio-RRC Mic jck to K3 Mic input B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 of 9

167 Cble 3.5 mm 3.5 mm Audio Output from Remote rdio to Rdio-RRC SP input jck Cble 3.5 mm 3.5 mm Keyer from Rdio- RRC PAD jck to Remote rdio stright key input jck Adpter ¼ to 3.5 mm Hedset dpter Adpter ¼ to 3.5 mm Pddle dpter B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 7 of 9

168 Front pnel view Mic Inp -pol Circulr 7 K3 Rdio RS-3 portcom DSUB- 9pol Mle GND PTT MICE MIC E Eb Ed Elecrft Twin cbles Control K3 to Control-RRC RRC5MkII AUX/MIC Pol RJ45 Con GND PTT MICE MIC RRC5MkII COM DSUB- 9pol Mle Cble E () SPEAKER 3.5 mm stereo plug USER MANUAL B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 of 9

169 SPEAKER 3.5 mm stereo plug RRC-5MkII COM DSUB- 9pol Femle E3c RRC-5MkII AUX/MIC -pol RJ 45 Con E Eb Ec Elecrft Twin cbles Rdio-RRC to Remote K3 Rdio RS-3 DSUB- 9pol Mle GND Front pnel view Cble E3 () 7 5 SPEAKER 3.5 mm stereo plug USER MANUAL 5 GND RRC5MkII I/O RJ MIC MICE PTT Rdio ACC port HDDSUB- 5pol VGA type Mle GND GND MIC MICE PTT 7 B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 9 of 9

170 ELECRAFT Generl User ppliction Speker Remote PA CW AF MIC CAT RRC-5MkIIs CW-Pddle Mic The Remoterig system works with both Elecrft K nd K3. Hrdwre configurtion JMP should be in plce when using Elecrft MH Mic nd removed when using for exmple Heil hedset. Rdio settings (exmple) Prmeter Control Rdio B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 70 of 9

171 Progrm mode 4 Yesu, Kenwood, Elecrft 4 Yesu, Kenwood, Elecrft SIP pssword hello hello SIP relm SIP contct Auto connect No Audio qulity Liner bits khz Liner bits khz Audio Dul-RX - Yes/No Codec out gin Codec inp gin 0 Codec inp premp Yes Codec inp HPF Hz 3 3 COM0 budrte COM0 dt bits COM0 stop bits COM0 prity 0 - Off 0 - Off (*) Avilble only in RRC-5MkIIs, remember tht the bndwidth demnd is doubled. Connections Control-RRC: Connect stndrd RS-3 cble between the PC nd the RRC COM. The microphone cn be connected direct to the RRC AUX/MIC connector if you hve microphone with RJ-45 connector. If you hve microphone with circulr connector you cn use the Remoterig K4 cble, use the MJ-, from Kenwood or mke one by yourself (drwings re provided). The speker is connected direct to the RRC SP-jck with 3.5 mm stereo plug. Rdio-RRC: From the RRC COM connector to the rdios KIO3 module connector (D-sub RS-3) you use stndrd RS-3 cble. Between the RRC AUX/MIC connector nd the rdios circulr microphone jck you cn use the Remoterig K5 cble or mke n dpter cble by yourself (drwings re provided). Mke the cble s short s possible to prevent it from picking up HF. The speker signl from the rdios externl speker jck to the RRC SP jck is connected vi stndrd "off- the-shelf cble with 3.5 mm stereo plugs in both ends. B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 7 of 9

172 E,E Ec,Ec B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 7 of 9

173 PC Speker/Hedset Connector DET NR. CNT NAME DIMENSION NOTE CONSTR. DRAWN COPIED CHECKED STAND. OK SCALE REPLACE REPLACED BY MS : Generic Elecrft cble Control -> RRC-5MkII RRC-5MkII DRAWING NR DATE Cble E () USER MANUAL Front pnel view Mic Inp -pol Circulr 7 GND PTT MICE MIC DSUB- 9pol Femle Sme s Kenwood MJ- E Eb Ec RRC-5MkII -pol RJ 45 Con GND PTT MICE MIC 7 DSUB- 9pol Mle COM SPEAKER 3.5 mm stereo plug B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 73 of 9

174 SPEAKER 3.5 mm stereo plug RRC-5MkII -pol RJ 45 Con COM DSUB- 9pol Femle 3 5 MIC MICE PTT GND GND E RRC-5MkII Ec Eb : Generic Elecrft cble RRC-5MkII -> Rdio Rdio RS-3 port DSUB- 9pol Mle 3 5 GND Mic Inp -pol Circulr MIC MICE PTT 7 Front pnel view Cble E () 7 5 SPEAKER 3.5 mm stereo plug USER MANUAL B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 74 of 9

175 ALINCO DX-SR nd DX-R Generl The technicl solution for the trnsceiver Alinco DX-SR nd the receiver DX-R is the sme s for IC-703/70, TS40 nd TS-000. All those trnsceivers re built in the wy tht the control pnel is working seprted from the rdio unit itself. We replce the cble between pnel nd rdio with to RRC-5, one connected to the control pnel nd one connected to the rdio. When you press the power button on the pnel the rdio comes to life t the remote side nd udio nd pnel info flows cross the internet between the RRC:s. The look nd feel of the control pnel is the sme s if the pnel ws directly connected to the rdio. B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 75 of 9

176 Hrdwre configurtion Rdio settings (exmple) Prmeter Control Rdio Progrm mode DX-SR DX-SR SIP pssword hello hello SIP relm SIP contct Auto connect No Audio qulity Liner bits khz Liner bits khz Audio dul-rx (*) No Codec out gin Codec inp gin 0 Codec inp premp Yes Codec inp HPF Hz 3 3 COM0 budrte COM0 dt bits COM0 stop bits COM0 prity 0 - Off 0 - Off (*) Avilble only in RRC-5MkIIs. Connections All necessry signls between the pnel nd the rdio re connected with the wires in the connection cble, stndrd ptch cble. We just need to use two stndrd ptch cbles, one between the control pnel nd the Control-RRC nd the other one between the Rdio-RRC nd the rdio. Convenient for trvelling is tht the speker is lredy present on the bck of the control pnel so there is no need for n extr speker even if bigger seprte speker gives better udio. The following signls re represented in the connection cble: B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 7 of 9

177 TXD - dt from rdio to control pnel RXD - dt from Control pnel to rdio 3 V - power to control pnel (when rdio is switched on) 4 Not in use 5 Mic signl / PWR on/off button GND 7 AF - Audio to speker. SPK GND - Speker ground Power supply Control-RRC: The Control-RRC is supplied with common 3. V (0-V) power supply. The disply nd speker mplifier needs lot of power so you need t lest A. B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 77 of 9

178 RRC-5MkII with -wire or 4-wire interfces Generl Control Rdio RRC-5MkII RRC-5MkII The RRC versions with -wire nd 4-wire interfces re minly used for remote control of commercil rdio systems which ws designed for lesed or 4 wire lines. The interfces re blnced nd re using trnsformers for isoltion nominl impednce is 00 ohm resistive. The 4-wire version cn be order with opto couplers for trnsfer of E nd M signls. Nominl udio level is -0 dbm nd mx level is bout +4 dbm. The system lso supports trnsfer of two independent seril ports. Hrdwre configurtion The Interfce PCB for nd 4-wires must be instlled t fctory. No other strppings needed. B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 7 of 9

179 Rdio settings (exmple) Prmeter Control Rdio Progrm mode Trnsprent 4-wire Trnsprent 4-wire SIP pssword hello hello SIP relm SIP contct Auto connect Yes Audio qulity Liner bits khz Liner bits khz Audio dul-rx (*) No Codec out gin Codec inp gin 4 (4w)/ (w) 4 (4w) / (w) Codec inp premp Yes Codec inp HPF Hz 3 3 COM0 budrte COM0 dt bits COM0 stop bits COM0 prity 0 - Off 0 - Off (*) Not pplicble. Connections Pin no -wire Interfce 4-wire Interfce AUX (RJ45) AUX (RJ45) E-In [-]* M-Out* 3 4-wire in [b] 4 -wire [] 4-wire out [] 5 -wire [b] 4-wire out [b] 4-wire in [b] 7 M-Out* E-In [+]* (*) E/M support hve to be ordered seprte. Power supply Control-RRC: B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 79 of 9

180 The Control-RRC is supplied with common 3. V (0-V) A power supply. B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 0 of 9

181 Schemtics I/O nd PAD interfce B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 of 9

182 MIC/AUX Interfce Control-RRC MkII B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 of 9

183 Speker output interfce Control-RRC MkIIs Speker input interfce Rdio-RRC MkIIs B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 3 of 9

184 MIC/AUX Interfce Rdio-RRC B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 4 of 9

185 Networks nd Firewlls One of the mjor obstcles when trying to remotely control something is the fct tht the Internet Service Provider (ISP) forces us to use dynmic IP ddresses. We cn never know, from time to time, which IP ddress our modem / firewll / router hs on its outside interfce (the IP ddress you will try to connect to). Most people use NAT routers tht trnsltes IP ddresses on the inside (your little LAN) to one common IP ddress on the outside using port conversion. To be ble to strem udio nd t the sme time trnsfer CAT / CI-V commnds or pnel-tordio communictions' we need to know which IP port numbers re used for ech service. There re some different techniques to fix this. At the opertor end (Control-RRC) there is normlly OK just to use DHCP for the own IPsettings. For the Sip contct prmeter you enter the public fixed IP ddress or DynDNSnme to the router t the rdio site. At the rdio end (Rdio-RRC) the router must be configured so tht port 500, 000 nd 000 (defult settings) is directed to the Rdio-RRC which should hve sttic IP ddress. The esy wy to get connected is to set the RRC IP ddress s DMZ server in the router. This mkes it possible to connect to ll services (SIP, udio nd control) s well s the web nd telnet interfces without further configurtion. If you re using SIP bsed IP telephony you need to chnge the port SIP port from 500 to n other port not used by the IP-telephony service in both RRC:s. If you run web server t the rdio site you need to chnge the webserver port from 0 to something else, for exmple 000. If you re using port forwrding you hve to configure the router in wy tht every service forwrds pckets to the right host on the inside. When setting up the router check tht there is No SIP ALG ctivted. You will lso need to register the Rdio-RRC to DynDNS ( so you cn use host nme to connect to the Rdio-RRC regrdless of its dynmic IP ddress (which cn chnge without notice, but rrely does). The following defult IP ports re used (chngeble) port number function 500 SIP (chnge this port number in both ends if you re using SIP bsed IPtelephony) 000 RTP, udio 000 DATA chnnel, control commnds 0 WEB interfce 3 Telnet Interfce SIP, RTP nd DATA protocols re UDP-bsed, WEB nd Telnet re TCP-bsed. B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 5 of 9

186 DMZ A typicl setup screen for ctivting DMZ is shown below. Enter the IP-number of the Rdio-RRC in box nd enble DMZ. B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 of 9

187 Portforwrding A typicl setup screen for ctivting port forwrding is shown below. There is one row ssigned for ech port (service) ll refereeing to the IP of the Rdio-RRC B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 7 of 9

188 SIP ALG If the router hs prmeter clled SIP ALG it should lwys be Disbled in both the Control nd rdio end. B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 of 9

189 Mobile Network Routers The Remoterig system cn be used with mobile networks routers lso. They re often clled 3G or 4G routers. They re configured in the sme wy s norml router. Before you order your 3G subscription check with the opertor tht they llow inbound connections from outside Internet, some opertors do not, nd you need tht if you will hve mobile router t the rdio site. Be wre of tht 3G router often dd ltency up to ms even if the bndwidth is high enough. This cn mke CW difficult but is seldom problem for voice communiction. With 3G we don t recommend using mobile connection in both ends, with 4G it s possible. B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 9 of 9

190 Appendix A - Audio coding Qulity or is recommended for short wve listening, they re good compromises between qulity nd need for bndwidth. Prcticl test hve shown tht qulity 0 (G7) is not the optiml coding if the signl to noise rtio is low which is common on the shortwve bnds. Qulity gives very good udio qulity even if you listen to music on FM. khz smple rte nd bits deep gives very good dynmic rnge nd lrge SNR nd good udio bndwidth. Qulity nd cn be used when very limit bndwidth is vilble, the udio qulity is reduced. The other qulities re more of cdemic interest. A good speker is lwys good investment lso. Note Different codings cn be used in the uplink nd downlink, which cn be useful in symmetricl Internet links like ADSL nd most mobile systems. Smple rte must be sme in both ends but coding cn be different. Audio qulity Coding Smple rte [khz] Bndwidth dul-rx=0 [kbps] Pcket size dul-rx=0 [ms] Bndwidth dul-rx= [kbps] 0 A-lw (G7) Liner-bits Liner-bits A-lw (G7) Liner-bits , 5 Liner-bits ,3 A-lw (G7) Liner-bits ,3 Liner-bits A-lw (G7) ,3 0 Liner-bits , 70,9 Liner-bits ,3 90,7 IMA ADPCM 4bits IMA ADPCM 4bits Pcket size dul-rx= [ms] B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 90 of 9

191 Appendix B - COM-port Keyer interfce There re lots of different solutions on the Internet, but this is very simple nd cn be implemented in the D-sub housing. No vlues re criticl; just use wht you hve in the junk box. B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 9 of 9

192 Appendix D - Technicl Dt Product/Art no: Remoterig RRC-5MkII Dimensions (LxHxD): Weight: Ip clss: Power supply requirement: Current drin t 3,V: Network connection: Speker mplifier: Mic input: Rdio protocol (detchble front): Rdio protocol (trditionl control): Protocol Internet: Codec: Bndwidth demnds: USB: Seril ports (trnsprent): CW-keyer: 5 x 40 x 34 mm x 50 g (excl. power supply) IP0 0-V DC vi DC Plug. mm/5.5mm App. 0 ma up to pp. 00 ma depending on udio level nd ev. Bck-lighter RJ45 T-Bse0/00 W ( ohm) Dynmic or Electret with DC feed Kenwood TS-40, TM-D70, TS-000 ICOM IC-703, IC-70, IC-E0, IC-R500, IC- 75, Alinco SR-DX ICOM CI-V, Kenwood PC-control, Yesu CAT, Elecrft TCP/IP, UDP, DHCP, SIP, RTP, DNS, DynDNS etc. G7 A-lw (khz/bit), khz/bit, khz/bit mm. From pp. 90 Kbit/s up to pp Mbit/s depending on codecs nd settings. USB.0 (mini) Usble temp rnge: 0 to +40 C Humidity rnge: x RS-3 (5700 bud) x TTL (5700 bud) 0-40 WPM, Imbic A/B, Squeeze, side-tone 30% to 90% RH B5B_RemoteRig_MkIIs-A User mnul Rev. A5 0 Nov 0 9 of 9

RRC-1258 MkII(s) m crob t. Yaesu Twin, Elecraft K3-Twin etc. User Manual USER MANUAL RRC-1258 MKII. User manual Rev. A feb 27 1 of 247

RRC-1258 MkII(s) m crob t. Yaesu Twin, Elecraft K3-Twin etc. User Manual USER MANUAL RRC-1258 MKII. User manual Rev. A feb 27 1 of 247 RRC-25 MkII(s) Yesu Twin, Elecrft K3-Twin etc. User Mnul B25B_RemoteRig_MkIIs-A3.docx User mnul Rev. A3 207 feb 27 of 247 Tble of contents Sttement of Conditions... 7 Generl Description... Detchble control

More information

RRC-1258 MkII(s) m crob t. Yaesu Twin, Elecraft K3-Twin etc. User Manual USER MANUAL RRC-1258 MKII. User manual Rev. A Feb 17 1 of 229

RRC-1258 MkII(s) m crob t. Yaesu Twin, Elecraft K3-Twin etc. User Manual USER MANUAL RRC-1258 MKII. User manual Rev. A Feb 17 1 of 229 RRC-25 MkII(s) Yesu Twin, Elecrft K3-Twin etc. User Mnul User mnul Rev. A30 204 Feb 7 of 229 Tble of contents Sttement of Conditions... 7 Generl Description... Detchble control pnel... 9 PC-bsed control...

More information

RC-1216H. Web based remote control for. SteppIR, ACOM-2000A and Rotators

RC-1216H. Web based remote control for. SteppIR, ACOM-2000A and Rotators Web bsed remote control for SteppIR, ACOM-2000A nd Rottors User Mnul B-RC1216H-PA7 User mnul Rev. PA7 2013 April 23 1 of 57 Tble of contents Sttement of Conditions... 4 Generl Description... 5 Step by

More information

AS Remote controlled Antenna switch

AS Remote controlled Antenna switch Remote controlled Antenn switch B-AS1269-PA4.docx User mnul Rev. PA4 2017 Okt 17 1 of 51 Tble of contents Sttement of Conditions... 4 Generl Description... 5 Step by step setup... 6 Hrdwre... 8 Bottom...

More information

RRC-1258 MkII(s) m crob t. User Manual USER MANUAL RRC-1258 MKII. User manual Rev. PA6 2 Nov of 127. Microbit 2.0 AB All rights reserved

RRC-1258 MkII(s) m crob t. User Manual USER MANUAL RRC-1258 MKII. User manual Rev. PA6 2 Nov of 127. Microbit 2.0 AB All rights reserved RRC-258 MkII(s) User Manual User manual Rev. PA 2 Nov 200 of 27 Table of contents Statement of Conditions... 5 General Description... Detachable control panel... PC-based control... 7 Step by step system

More information

McAfee Network Security Platform

McAfee Network Security Platform Mnger Applince Quick Strt Guide Revision B McAfee Network Security Pltform This guide is high-level description of how to instll nd configure the Mnger Applince. For more detiled instlltion informtion,

More information

EasyMP Network Projection Operation Guide

EasyMP Network Projection Operation Guide EsyMP Network Projection Opertion Guide Contents 2 Introduction to EsyMP Network Projection EsyMP Network Projection Fetures... 5 Disply Options... 6 Multi-Screen Disply Function... 6 Movie Sending Mode...

More information

EasyMP Multi PC Projection Operation Guide

EasyMP Multi PC Projection Operation Guide EsyMP Multi PC Projection Opertion Guide Contents 2 Introduction to EsyMP Multi PC Projection 5 EsyMP Multi PC Projection Fetures... 6 Connection to Vrious Devices... 6 Four-Pnel Disply... 6 Chnge Presenters

More information

Epson iprojection Operation Guide (Windows/Mac)

Epson iprojection Operation Guide (Windows/Mac) Epson iprojection Opertion Guide (Windows/Mc) Contents 2 Introduction to Epson iprojection 5 Epson iprojection Fetures... 6 Connection to Vrious Devices... 6 Four-Pnel Disply... 6 Chnge Presenters nd Projection

More information

Information regarding

Information regarding Informtion regrding LANCOM Advnced VPN Client 3.13 Copyright (c) 2002-2017 LANCOM Systems GmbH, Wuerselen (Germny) LANCOM Systems GmbH does not tke ny gurntee nd libility for softwre not developed, mnufctured

More information

E201 USB Encoder Interface

E201 USB Encoder Interface Dt sheet Issue 4, 24 th ugust 2015 E201 USB Encoder Interfce E201-9Q incrementl E201-9S bsolute bsolute SSI BiSS-C mode (unidirectionl) B Z Clock Dt M SLO The E201 is single chnnel USB encoder interfce

More information

Epson Projector Content Manager Operation Guide

Epson Projector Content Manager Operation Guide Epson Projector Content Mnger Opertion Guide Contents 2 Introduction to the Epson Projector Content Mnger Softwre 3 Epson Projector Content Mnger Fetures... 4 Setting Up the Softwre for the First Time

More information

EasyMP Network Projection Operation Guide

EasyMP Network Projection Operation Guide EsyMP Network Projection Opertion Guide Contents 2 About EsyMP Network Projection Functions of EsyMP Network Projection... 5 Vrious Screen Trnsfer Functions... 5 Instlling the Softwre... 6 Softwre Requirements...6

More information

Simrad ES80. Software Release Note Introduction

Simrad ES80. Software Release Note Introduction Simrd ES80 Softwre Relese 1.3.0 Introduction This document descries the chnges introduced with the new softwre version. Product: ES80 Softwre version: 1.3.0 This softwre controls ll functionlity in the

More information

pdfapilot Server 2 Manual

pdfapilot Server 2 Manual pdfpilot Server 2 Mnul 2011 by clls softwre gmbh Schönhuser Allee 6/7 D 10119 Berlin Germny info@cllssoftwre.com www.cllssoftwre.com Mnul clls pdfpilot Server 2 Pge 2 clls pdfpilot Server 2 Mnul Lst modified:

More information

Welch Allyn CardioPerfect Workstation Installation Guide

Welch Allyn CardioPerfect Workstation Installation Guide Welch Allyn CrdioPerfect Worksttion Instlltion Guide INSTALLING CARDIOPERFECT WORKSTATION SOFTWARE & ACCESSORIES ON A SINGLE PC For softwre version 1.6.6 or lter For network instlltion, plese refer to

More information

EasyMP Multi PC Projection Operation Guide

EasyMP Multi PC Projection Operation Guide EsyMP Multi PC Projection Opertion Guide Contents 2 About EsyMP Multi PC Projection Meeting Styles Proposed by EsyMP Multi PC Projection... 5 Holding Meetings Using Multiple Imges... 5 Holding Remote Meetings

More information

IZT DAB ContentServer, IZT S1000 Testing DAB Receivers Using ETI

IZT DAB ContentServer, IZT S1000 Testing DAB Receivers Using ETI IZT DAB ContentServer, IZT S1000 Testing DAB Receivers Using ETI Appliction Note Rel-time nd offline modultion from ETI files Generting nd nlyzing ETI files Rel-time interfce using EDI/ETI IZT DAB CONTENTSERVER

More information

EasyMP Multi PC Projection Operation Guide

EasyMP Multi PC Projection Operation Guide EsyMP Multi PC Projection Opertion Guide Contents 2 About EsyMP Multi PC Projection Meeting Styles Proposed by EsyMP Multi PC Projection... 5 Holding Meetings Using Multiple Imges... 5 Holding Remote Meetings

More information

Release Notes for. LANCOM Advanced VPN Client 4.10 Rel

Release Notes for. LANCOM Advanced VPN Client 4.10 Rel Relese Notes for LANCOM Advnced VPN Client 4.10 Rel Copyright (c) 2002-2018 LANCOM Systems GmbH, Wuerselen (Germny) LANCOM Systems GmbH does not tke ny gurntee nd libility for softwre not developed, mnufctured

More information

LCI/USB LonWorks Commissioning Interface

LCI/USB LonWorks Commissioning Interface Works Commissioning Interfce Importnt: Retin these instructions CONTENTS 1 Unpcking... 1 2 Storing... 1 3 Instlltion... 1 4 Uninstlling the USB Drivers... 8 5 Disposl... 8 1 UNPACKING Instlltion Instructions

More information

Passwords Passwords Changing Passwords... <New Passwords> 130 Setting UIM PIN... <UIM PIN/UIM PIN2> 130 Unlocking a Locked UIM...

Passwords Passwords Changing Passwords... <New Passwords> 130 Setting UIM PIN... <UIM PIN/UIM PIN2> 130 Unlocking a Locked UIM... Psswords Psswords... 128 Chnging Psswords... 130 Setting UIM PIN... 130 Unlocking Locked UIM... 131 Restricting the Hndset Opertions Locking Function... 131 Locking the

More information

License Manager Installation and Setup

License Manager Installation and Setup The Network License (concurrent-user) version of e-dpp hs hrdwre key plugged to the computer running the License Mnger softwre. In the e-dpp terminology, this computer is clled the License Mnger Server.

More information

McAfee Network Security Platform

McAfee Network Security Platform NTBA Applince T-200 nd T-500 Quick Strt Guide Revision B McAfee Network Security Pltform 1 Instll the mounting rils Position the mounting rils correctly nd instll them t sme levels. At the front of the

More information

McAfee Network Security Platform

McAfee Network Security Platform 10/100/1000 Copper Active Fil-Open Bypss Kit Guide Revision E McAfee Network Security Pltform This document descries the contents nd how to instll the McAfee 10/100/1000 Copper Active Fil-Open Bypss Kit

More information

LINX MATRIX SWITCHERS FIRMWARE UPDATE INSTRUCTIONS FIRMWARE VERSION

LINX MATRIX SWITCHERS FIRMWARE UPDATE INSTRUCTIONS FIRMWARE VERSION Overview LINX MATRIX SWITCHERS FIRMWARE UPDATE INSTRUCTIONS FIRMWARE VERSION 4.3.1.0 Due to the complex nture of this updte, plese fmilirize yourself with these instructions nd then contct RGB Spectrum

More information

Installation Guide AT-VTP-800

Installation Guide AT-VTP-800 Velocity 8 Touch Pnel The Atlon -BL nd -WH re 8 touch pnels in blck nd white, respectively, for the Atlon Velocity Control System. They feture contemporry, refined styling for modern presenttion environments

More information

E201 USB Encoder Interface

E201 USB Encoder Interface Dt sheet Issue 3, 14 th July 2014 E201 USB Encoder Interfce E201-9Q - incrementl E201-9S - bsolute bsolute SSI BiSS-C mode (unidirectionl) B Z Clock Dt M SLO The E201 is single chnnel USB encoder interfce

More information

Release Notes for. LANtools Software Release RU6

Release Notes for. LANtools Software Release RU6 Relese Notes for LANtools Softwre Relese 10.12 RU6 Copyright (c) 2002-2018 LANCOM Systems GmbH, Wuerselen (Germny) LANCOM Systems GmbH does not tke ny gurntee nd libility for softwre not developed, mnufctured

More information

File Manager Quick Reference Guide. June Prepared for the Mayo Clinic Enterprise Kahua Deployment

File Manager Quick Reference Guide. June Prepared for the Mayo Clinic Enterprise Kahua Deployment File Mnger Quick Reference Guide June 2018 Prepred for the Myo Clinic Enterprise Khu Deployment NVIGTION IN FILE MNGER To nvigte in File Mnger, users will mke use of the left pne to nvigte nd further pnes

More information

MIPS I/O and Interrupt

MIPS I/O and Interrupt MIPS I/O nd Interrupt Review Floting point instructions re crried out on seprte chip clled coprocessor 1 You hve to move dt to/from coprocessor 1 to do most common opertions such s printing, clling functions,

More information

Easy Interactive Tools Ver.3.0 Operation Guide

Easy Interactive Tools Ver.3.0 Operation Guide Esy Interctive Tools Ver.3.0 Opertion Guide Esy Interctive Tools Summry 2 Fetures Esy Interctive Tools is n ppliction tht llows you to drw on projected imges. By using the interctive pen supplied with

More information

Deposit a Technical Report in PubRep

Deposit a Technical Report in PubRep Technicl in Lst Updte:19.12.016 Te c h n i c l Technicl s re mjor source of scientific informtion, prepred for institutionl nd wider distribution. They re considered grey literture since they re scientific

More information

NOTES. Figure 1 illustrates typical hardware component connections required when using the JCM ICB Asset Ticket Generator software application.

NOTES. Figure 1 illustrates typical hardware component connections required when using the JCM ICB Asset Ticket Generator software application. ICB Asset Ticket Genertor Opertor s Guide Septemer, 2016 Septemer, 2016 NOTES Opertor s Guide ICB Asset Ticket Genertor Softwre Instlltion nd Opertion This document contins informtion for downloding, instlling,

More information

Migrating vrealize Automation to 7.3 or March 2018 vrealize Automation 7.3

Migrating vrealize Automation to 7.3 or March 2018 vrealize Automation 7.3 Migrting vrelize Automtion to 7.3 or 7.3.1 15 Mrch 2018 vrelize Automtion 7.3 You cn find the most up-to-dte technicl documenttion on the VMwre website t: https://docs.vmwre.com/ If you hve comments bout

More information

NetBackup 5200 Release 1.1 Quick Installation Guide

NetBackup 5200 Release 1.1 Quick Installation Guide NetBckup 5200 Relese 1.1 Quick Instlltion Guide Revision: 01 Dte: 2010-08-30 Environment Check Before Instlltion You cn instll the NetBckup 5200 pplince in stndrd 19-inch cbinet (with n AC distribution

More information

JCM TRAINING OVERVIEW DBV Series DBV-500 Banknote Validator

JCM TRAINING OVERVIEW DBV Series DBV-500 Banknote Validator November, 2016 JCM TRAINING OVERVIEW DBV Series DBV-500 Bnknote Vlidtor Phone (800) 683-7248 (702) 651-0000 Fx (702) 651-0214 E-mil support@jcmglobl.com www.jcmglobl.com 1 DBV-500 Bnknote Vlidtor Tble

More information

Address/Data Control. Port latch. Multiplexer

Address/Data Control. Port latch. Multiplexer 4.1 I/O PORT OPERATION As discussed in chpter 1, ll four ports of the 8051 re bi-directionl. Ech port consists of ltch (Specil Function Registers P0, P1, P2, nd P3), n output driver, nd n input buffer.

More information

Engineer-to-Engineer Note

Engineer-to-Engineer Note Engineer-to-Engineer Note EE-232 Technicl notes on using Anlog Devices DSPs, processors nd development tools Contct our technicl support t dsp.support@nlog.com nd t dsptools.support@nlog.com Or visit our

More information

Engineer To Engineer Note

Engineer To Engineer Note Engineer To Engineer Note EE-208 Technicl Notes on using Anlog Devices' DSP components nd development tools Contct our technicl support by phone: (800) ANALOG-D or e-mil: dsp.support@nlog.com Or visit

More information

TECHNICAL NOTE MANAGING JUNIPER SRX PCAP DATA. Displaying the PCAP Data Column

TECHNICAL NOTE MANAGING JUNIPER SRX PCAP DATA. Displaying the PCAP Data Column TECHNICAL NOTE MANAGING JUNIPER SRX PCAP DATA APRIL 2011 If your STRM Console is configured to integrte with the Juniper JunOS Pltform DSM, STRM cn receive, process, nd store Pcket Cpture (PCAP) dt from

More information

Installation manual. Daikin Altherma low temperature monobloc option box EK2CB07CAV3. Installation manual. English

Installation manual. Daikin Altherma low temperature monobloc option box EK2CB07CAV3. Installation manual. English Instlltion mnul Dikin Altherm low temperture monobloc option box EKCB07CAV Instlltion mnul Dikin Altherm low temperture monobloc option box English Tble of Contents Tble of Contents About the documenttion.

More information

LoRaWANTM Concentrator Card Mini PCIe LRWCCx-MPCIE-868

LoRaWANTM Concentrator Card Mini PCIe LRWCCx-MPCIE-868 Dt Sheet LoRWANTM Concentrtor Crd Mini PCIe LRWCCxMPCIE868 LoRWANTM Concentrtor Crd bsed on Semtech SX30 nd SX308 Chips in Mini PCIe Form Fctor The nfuse LRWCCxMPCIE fmily of crds enble OEMs nd system

More information

vcloud Director Service Provider Admin Portal Guide vcloud Director 9.1

vcloud Director Service Provider Admin Portal Guide vcloud Director 9.1 vcloud Director Service Provider Admin Portl Guide vcloud Director 9. vcloud Director Service Provider Admin Portl Guide You cn find the most up-to-dte technicl documenttion on the VMwre website t: https://docs.vmwre.com/

More information

Engineer To Engineer Note

Engineer To Engineer Note Engineer To Engineer Note EE-169 Technicl Notes on using Anlog Devices' DSP components nd development tools Contct our technicl support by phone: (800) ANALOG-D or e-mil: dsp.support@nlog.com Or visit

More information

Unit #9 : Definite Integral Properties, Fundamental Theorem of Calculus

Unit #9 : Definite Integral Properties, Fundamental Theorem of Calculus Unit #9 : Definite Integrl Properties, Fundmentl Theorem of Clculus Gols: Identify properties of definite integrls Define odd nd even functions, nd reltionship to integrl vlues Introduce the Fundmentl

More information

McAfee Network Security Platform

McAfee Network Security Platform Revision D McAfee Network Security Pltform (NS5x00 Quick Strt Guide) This quick strt guide explins how to quickly set up nd ctivte your McAfee Network Security Pltform NS5100 nd NS5200 Sensors in inline

More information

Zenoss Core Installation Guide

Zenoss Core Installation Guide Zenoss Core Instlltion Guide Relese 5.2.1 Zenoss, Inc. www.zenoss.com Zenoss Core Instlltion Guide Copyright 2017 Zenoss, Inc. All rights reserved. Zenoss nd the Zenoss logo re trdemrks or registered trdemrks

More information

Zenoss Resource Manager Installation Guide

Zenoss Resource Manager Installation Guide Zenoss Resource Mnger Instlltion Guide Relese 5.2.5 Zenoss, Inc. www.zenoss.com Zenoss Resource Mnger Instlltion Guide Copyright 2017 Zenoss, Inc. All rights reserved. Zenoss nd the Zenoss logo re trdemrks

More information

CKX-CCSW Confluency checker INSTRUCTIONS. Software for research/education This software is designed to use in research and or education fields.

CKX-CCSW Confluency checker INSTRUCTIONS. Software for research/education This software is designed to use in research and or education fields. INSTRUCTIONS Confluency checker NOTE: This instruction mnul is for the Olympus confluency checker. To ensure the sfety, obtin optimum performnce nd to fmilirize yourself fully with the use of this softwre,

More information

vcloud Director Tenant Portal Guide vcloud Director 9.1

vcloud Director Tenant Portal Guide vcloud Director 9.1 vcloud Director Tennt Portl Guide vcloud Director 9.1 You cn find the most up-to-dte technicl documenttion on the VMwre website t: https://docs.vmwre.com/ If you hve comments bout this documenttion, submit

More information

pdftoolbox Server 4 Manual

pdftoolbox Server 4 Manual pdftoolbox Server 4 Mnul Mnul Pge 2 Mnul Lst modified: 27 Februry 2009 2009 by clls softwre gmbh, Berlin, Germny All rights reserved All trdemrks re the property of their respective owners. Mnul Pge Content

More information

OPERATION MANUAL. DIGIFORCE 9307 PROFINET Integration into TIA Portal

OPERATION MANUAL. DIGIFORCE 9307 PROFINET Integration into TIA Portal OPERATION MANUAL DIGIFORCE 9307 PROFINET Integrtion into TIA Portl Mnufcturer: 2018 burster präzisionsmesstechnik gmbh & co kg burster präzisionsmesstechnik gmbh & co kg Alle Rechte vorbehlten Tlstrße

More information

Chapter 7. Routing with Frame Relay, X.25, and SNA. 7.1 Routing. This chapter discusses Frame Relay, X.25, and SNA Routing. Also see the following:

Chapter 7. Routing with Frame Relay, X.25, and SNA. 7.1 Routing. This chapter discusses Frame Relay, X.25, and SNA Routing. Also see the following: Chpter 7 Routing with Frme Rely, X.25, nd SNA This chpter discusses Frme Rely, X.25, nd SNA Routing. Also see the following: Section 4.2, Identifying the BANDIT in the Network Section 4.3, Defining Globl

More information

DMXter4 RDM software release notes September 28,2010 Software V4.10

DMXter4 RDM software release notes September 28,2010 Software V4.10 DMXter4 RDM softwre relese notes September 28,2010 Softwre V4.10 New Fetures in V4.10 DMX! Drive Line Sttic in the Advnced Trnsmit Menu This llows stble known drive stte to be sent for testing receivers.

More information

a Technical Notes on using Analog Devices' DSP components and development tools

a Technical Notes on using Analog Devices' DSP components and development tools Engineer To Engineer Note EE-146 Technicl Notes on using Anlog Devices' DSP components nd development tools Contct our technicl support by phone: (800) ANALOG-D or e-mil: dsp.support@nlog.com Or visit

More information

MULTIPLE INTERFACE SHAFT ENCODER MODEL OPERATIONS & MAINTENANCE MANUAL

MULTIPLE INTERFACE SHAFT ENCODER MODEL OPERATIONS & MAINTENANCE MANUAL MULTIPLE INTERFACE SHAFT ENCODER MODEL 56-0540 OPERATIONS & MAINTENANCE MANUAL Prt No. 8800-1137 Revision - B 7-Oct-04 Sutron Corportion 21300 Ridgetop Circle Sterling, VA 20166 (703)406-2800 (703)406-2801

More information

Small Business Networking

Small Business Networking Why network is n essentil productivity tool for ny smll business Effective technology is essentil for smll businesses looking to increse the productivity of their people nd business. Introducing technology

More information

Agilent Mass Hunter Software

Agilent Mass Hunter Software Agilent Mss Hunter Softwre Quick Strt Guide Use this guide to get strted with the Mss Hunter softwre. Wht is Mss Hunter Softwre? Mss Hunter is n integrl prt of Agilent TOF softwre (version A.02.00). Mss

More information

Zenoss Resource Manager Installation Guide

Zenoss Resource Manager Installation Guide Zenoss Resource Mnger Instlltion Guide Relese 6.1.1 Zenoss, Inc. www.zenoss.com Zenoss Resource Mnger Instlltion Guide Copyright 2018 Zenoss, Inc. All rights reserved. Zenoss, Own IT, nd the Zenoss logo

More information

Digital Design. Chapter 1: Introduction. Digital Design. Copyright 2006 Frank Vahid

Digital Design. Chapter 1: Introduction. Digital Design. Copyright 2006 Frank Vahid Chpter : Introduction Copyright 6 Why Study?. Look under the hood of computers Solid understnding --> confidence, insight, even better progrmmer when wre of hrdwre resource issues Electronic devices becoming

More information

Tixeo compared to other videoconferencing solutions

Tixeo compared to other videoconferencing solutions compred to other videoconferencing solutions for V171026EN , unique solution on the video conferencing field Adobe Connect Web RTC Vydio for High security level, privcy Zero impct on network security policies

More information

STRM Installation Guide

STRM Installation Guide Security Thret Response Mnger Relese 2013.2 Juniper Networks, Inc. 1194 North Mthild Avenue Sunnyvle, CA 94089 USA 408-745-2000 www.juniper.net Published: 2014-09-15 Copyright Notice Copyright 2014 Juniper

More information

Midterm 2 Sample solution

Midterm 2 Sample solution Nme: Instructions Midterm 2 Smple solution CMSC 430 Introduction to Compilers Fll 2012 November 28, 2012 This exm contins 9 pges, including this one. Mke sure you hve ll the pges. Write your nme on the

More information

Enginner To Engineer Note

Enginner To Engineer Note Technicl Notes on using Anlog Devices DSP components nd development tools from the DSP Division Phone: (800) ANALOG-D, FAX: (781) 461-3010, EMAIL: dsp_pplictions@nlog.com, FTP: ftp.nlog.com Using n ADSP-2181

More information

JCM TRAINING OVERVIEW ivizion Banknote Acceptor

JCM TRAINING OVERVIEW ivizion Banknote Acceptor ivizion Bnknote Acceptor JCM Trining Overview Februry, 2018 Februry, 2018 ivizion-100 Prts List Prt Number - Description 701-000269R ivizion/uba Power Supply 701-100112R ivizion/tbv UAC Kit (lternte power

More information

Installation Instructions for the TBVL Valve Set GOLD/COMPACT

Installation Instructions for the TBVL Valve Set GOLD/COMPACT Instlltion Instructions for the TBVL Vlve Set GOLD/COMPACT. Generl The TBVL vlve set is set of components for controlling n ir heter/ir cooler nd consists of ()-wy vlve, vlve ctutor, connection cble with

More information

Zenoss Core Installation Guide

Zenoss Core Installation Guide Zenoss Core Instlltion Guide Relese 6.1.0 Zenoss, Inc. www.zenoss.com Zenoss Core Instlltion Guide Copyright 2018 Zenoss, Inc. All rights reserved. Zenoss, Own IT, nd the Zenoss logo re trdemrks or registered

More information

Beginner s Guide to the Environment

Beginner s Guide to the Environment Beginner s Guide to the Environment by Len Ssso for Version 3.0 e October 1997 E Soft- und Hrdwre GmbH Tble of Contents Chpter 1 Overview of the Environment Chpter 2 Some Things Chnge Some Things Sty The

More information

QEL 33A/35A, 98/99 Series

QEL 33A/35A, 98/99 Series *24908394* 24908394 Bseplte Conversion Kit QEL 33A/35A, 98/99 Series Instlltion Instructions 1. This kit converts ll 33/35A nd 98/99 series EL devices nd fire devices uilt prior to Oct. 2014 to quiet electric

More information

Setup Guide. Before Setting Up the Printer

Setup Guide. Before Setting Up the Printer Introduction Cution Series Series Setup Guide Series Introductory Informtion Instructions in this Setup Guide show the ipf840 printer. Note tht your printer my look different from these illustrtions in

More information

Engineer To Engineer Note

Engineer To Engineer Note Engineer To Engineer Note EE-188 Technicl Notes on using Anlog Devices' DSP components nd development tools Contct our technicl support by phone: (800) ANALOG-D or e-mil: dsp.support@nlog.com Or visit

More information

Small Business Networking

Small Business Networking Why network is n essentil productivity tool for ny smll business Effective technology is essentil for smll businesses looking to increse the productivity of their people nd business. Introducing technology

More information

PNC NC code PROGRAMMER'S MANUAL

PNC NC code PROGRAMMER'S MANUAL PNC-3200 NC code PROGRAMMER'S MANUAL Thnk you very much for purchsing the PNC-3200. To ensure correct nd sfe usge with full understnding of this product's performnce, plese be sure to red through this

More information

vcloud Director Service Provider Admin Portal Guide 04 OCT 2018 vcloud Director 9.5

vcloud Director Service Provider Admin Portal Guide 04 OCT 2018 vcloud Director 9.5 vcloud Director Service Provider Admin Portl Guide 04 OCT 208 vcloud Director 9.5 You cn find the most up-to-dte technicl documenttion on the VMwre website t: https://docs.vmwre.com/ If you hve comments

More information

Zenoss Resource Manager Installation Guide

Zenoss Resource Manager Installation Guide Zenoss Resource Mnger Instlltion Guide Relese 5.3.0 Zenoss, Inc. www.zenoss.com Zenoss Resource Mnger Instlltion Guide Copyright 2017 Zenoss, Inc. All rights reserved. Zenoss, Own IT, nd the Zenoss logo

More information

Chapter 1: Introduction

Chapter 1: Introduction Chpter : Introduction Slides to ccompny the textbook, First Edition, by, John Wiley nd Sons Publishers, 7. http://www.ddvhid.com Copyright 7 Instructors of courses requiring Vhid's textbook (published

More information

McAfee Network Security Platform

McAfee Network Security Platform NS7x00 Quick Strt Guide Revision D McAfee Network Security Pltform This quick strt guide explins how to quickly set up nd ctivte your McAfee Network Security Pltform NS7100, NS7200, nd NS7300 Sensors in

More information

Lab 1 - Counter. Create a project. Add files to the project. Compile design files. Run simulation. Debug results

Lab 1 - Counter. Create a project. Add files to the project. Compile design files. Run simulation. Debug results 1 L 1 - Counter A project is collection mechnism for n HDL design under specifiction or test. Projects in ModelSim ese interction nd re useful for orgnizing files nd specifying simultion settings. The

More information

Geometric transformations

Geometric transformations Geometric trnsformtions Computer Grphics Some slides re bsed on Shy Shlom slides from TAU mn n n m m T A,,,,,, 2 1 2 22 12 1 21 11 Rows become columns nd columns become rows nm n n m m A,,,,,, 1 1 2 22

More information

Engineer-to-Engineer Note

Engineer-to-Engineer Note Engineer-to-Engineer Note EE-204 Technicl notes on using Anlog Devices DSPs, processors nd development tools Visit our Web resources http://www.nlog.com/ee-notes nd http://www.nlog.com/processors or e-mil

More information

Zenoss Resource Manager Installation Guide

Zenoss Resource Manager Installation Guide Zenoss Resource Mnger Instlltion Guide Relese 5.3.2 Zenoss, Inc. www.zenoss.com Zenoss Resource Mnger Instlltion Guide Copyright 2017 Zenoss, Inc. All rights reserved. Zenoss, Own IT, nd the Zenoss logo

More information

Easy Interactive Tools Ver.4.1 Operation Guide

Easy Interactive Tools Ver.4.1 Operation Guide Esy Interctive Tools Ver.4.1 Opertion Guide Esy Interctive Tools Ver.4.1 Opertion Guide Esy Interctive Tools Summry 3 Fetures Esy Interctive Tools is n ppliction tht llows you to drw on projected imges.

More information

vcloud Director Tenant Portal Guide vcloud Director 9.0

vcloud Director Tenant Portal Guide vcloud Director 9.0 vcloud Director Tennt Portl Guide vcloud Director 9.0 vcloud Director Tennt Portl Guide You cn find the most up-to-dte technicl documenttion on the VMwre We site t: https://docs.vmwre.com/ The VMwre We

More information

Small Business Networking

Small Business Networking Why network is n essentil productivity tool for ny smll business Effective technology is essentil for smll businesses looking to increse the productivity of their people nd business. Introducing technology

More information

CS 268: IP Multicast Routing

CS 268: IP Multicast Routing Motivtion CS 268: IP Multicst Routing Ion Stoic April 5, 2004 Mny pplictions requires one-to-mny communiction - E.g., video/udio conferencing, news dissemintion, file updtes, etc. Using unicst to replicte

More information

GXR-GPS GXR-GPS-485 User Manual

GXR-GPS GXR-GPS-485 User Manual GXR-GPS GXR-GPS-485 User Mnul GeoSIG Ltd, Wiesenstrsse 39, 8952 Schlieren, Switzerlnd Phone: + 41 44 810 2150, Fx: + 41 44 810 2350 info@geosig.com, www.geosig.com Pge ii Document Revision GS_GXR_GPS_User_Mnul_V05.doc

More information

Small Business Networking

Small Business Networking Why network is n essentil productivity tool for ny smll business Effective technology is essentil for smll businesses looking to increse the productivity of their people nd processes. Introducing technology

More information

Small Business Networking

Small Business Networking Why network is n essentil productivity tool for ny smll business Effective technology is essentil for smll businesses looking to increse the productivity of their people nd processes. Introducing technology

More information

Small Business Networking

Small Business Networking Why network is n essentil productivity tool for ny smll business Effective technology is essentil for smll businesses looking to increse the productivity of their people nd processes. Introducing technology

More information

c360 Add-On Solutions

c360 Add-On Solutions c360 Add-On Solutions Functionlity Dynmics CRM 2011 c360 Record Editor Reltionship Explorer Multi-Field Serch Alerts Console c360 Core Productivity Pck "Does your tem resist using CRM becuse updting dt

More information

COMPUTER EDUCATION TECHNIQUES, INC. (MS_W2K3_SERVER ) SA:

COMPUTER EDUCATION TECHNIQUES, INC. (MS_W2K3_SERVER ) SA: In order to lern which questions hve een nswered correctly: 1. Print these pges. 2. Answer the questions. 3. Send this ssessment with the nswers vi:. FAX to (212) 967-3498. Or. Mil the nswers to the following

More information

Easy Interactive Tools Ver.4.2 Operation Guide

Easy Interactive Tools Ver.4.2 Operation Guide Esy Interctive Tools Ver.4.2 Opertion Guide Esy Interctive Tools Ver.4.2 Opertion Guide Esy Interctive Tools Summry 3 Fetures Esy Interctive Tools is n ppliction tht llows you to drw on projected imges.

More information

How to Design REST API? Written Date : March 23, 2015

How to Design REST API? Written Date : March 23, 2015 Visul Prdigm How Design REST API? Turil How Design REST API? Written Dte : Mrch 23, 2015 REpresenttionl Stte Trnsfer, n rchitecturl style tht cn be used in building networked pplictions, is becoming incresingly

More information

Engineer-to-Engineer Note

Engineer-to-Engineer Note Engineer-to-Engineer Note EE-245 Technicl notes on using Anlog Devices DSPs, processors nd development tools Contct our technicl support t dsp.support@nlog.com nd t dsptools.support@nlog.com Or visit our

More information

IBM System Storage SAN Volume Controller. Troubleshooting Guide IBM

IBM System Storage SAN Volume Controller. Troubleshooting Guide IBM IBM System Storge SAN Volume Controller Troubleshooting Guide IBM Note Before using this informtion nd the product it supports, red the informtion in Notices on pge 309. This edition pplies to version

More information

Start Here. Remove all tape and lift display. Locate components

Start Here. Remove all tape and lift display. Locate components HP Photosmrt 2600/2700 series ll-in-one User Guide Strt Here 1 USB cle users: Do not connect the USB cle until this guide instructs you to or the softwre my not instll properly. Use this guide to set up

More information

UT1553B BCRT True Dual-port Memory Interface

UT1553B BCRT True Dual-port Memory Interface UTMC APPICATION NOTE UT553B BCRT True Dul-port Memory Interfce INTRODUCTION The UTMC UT553B BCRT is monolithic CMOS integrted circuit tht provides comprehensive MI-STD- 553B Bus Controller nd Remote Terminl

More information

Engineer-to-Engineer Note

Engineer-to-Engineer Note Engineer-to-Engineer Note EE-295 Technicl notes on using Anlog Devices DSPs, processors nd development tools Visit our Web resources http://www.nlog.com/ee-notes nd http://www.nlog.com/processors or e-mil

More information

800W Programmable Single Output

800W Programmable Single Output Fetures: U Design Progrmmle output Voltge (0% ~ 05%) Universl AC input / Full rnge Progrmmle output Current (0% ~ 05%) Refer to pg. 5 for connection digrm) Forced current shring t prllel opertion Constnt

More information