LED light engines ready2apply. Module SLA DC G2 50mm SNC Modules SLA ESSENCE

Transcription

1 Module SLA DC G2 5mm SNC Modules SLA ESSENCE Product description Fits in most existing MR16 / GU1 halogen luminaires Replacement of 5 W MR16 halogen lamps or 2 W HID lamp Module with integrated heatsink and optics Free choice of variable dimming and non-dimming LED Drivers Pre-wired for quick and easy installation Eye-catching lens optic with mirrors halogen facettes Module luminous efficacy up to 14 lm/w Higher CRI, typical Ra = 92 Colour temperatures 2,7 K, 3, K, 4, K High colour consistency (MacAdam 3) Beam Angle: spot degree (24 ) or downlight (36 ) Long life-time: L7B5 >5, h 5-year guarantee SLA DC G2 5mm 7lm SNC SLA DC G2 5mm 12lm SNC È Standards, page 3 Colour temperatures and tolerances, page 3 1

2 Module SLA DC G2 5mm SNC Modules SLA ESSENCE Technical data Ambient temperature range C tp rated for SLA DC 7lm C tp rated for SLA DC 12lm 75 C tc for SLA DC 7lm 75 C tc for SLA DC 12lm 9 C Irated for SLA DC 7lm 25 ma Irated for SLA DC 12lm 35 ma Imax for SLA DC 7lm 3 ma Imax for SLA DC 12lm 38 ma Max. permissible LF current ripple for SLA DC 7lm 9 ma Max. permissible LF current ripple for SLA DC 12lm 1,3 ma Max. permissible peak current for SLA DC 7lm 1,2 ma / max. 1 ms Max. permissible peak current for SLA DC 12lm 1,45 ma / max. 1 ms Max. working voltage for insulation SELV V Insulation test voltage.5 kv ESD classification severity level 2 Risk group (EN 62471:28) RG1 Type of protection IP2 7 tc, tp tc, tp ø49,6 ø49,6 SLA DC G2 5mm 7lm SLA DC G2 5mm 12lm tc, tp... red marked Ordering data Type Article number Colour temperaturepackaging Weight per pc. SLA DC G2 5mm 7lm D SNC ,7 K 8 pc(s)..9 kg SLA DC G2 5mm 7lm D SNC ,7 K 8 pc(s)..9 kg SLA DC G2 5mm 7lm 93 24D SNC , K 8 pc(s)..9 kg SLA DC G2 5mm 7lm 93 36D SNC , K 8 pc(s)..9 kg SLA DC G2 5mm 7lm 9 24D SNC , K 8 pc(s)..9 kg SLA DC G2 5mm 7lm 9 36D SNC , K 8 pc(s)..9 kg SLA DC G2 5mm 12lm D SNC ,7 K 8 pc(s)..11 kg SLA DC G2 5mm 12lm D SNC ,7 K 8 pc(s)..11 kg SLA DC G2 5mm 12lm 93 24D SNC , K 8 pc(s)..11 kg SLA DC G2 5mm 12lm 93 36D SNC , K 8 pc(s)..11 kg SLA DC G2 5mm 12lm 9 24D SNC , K 8 pc(s)..11 kg SLA DC G2 5mm 12lm 9 36D SNC , K 8 pc(s)..11 kg Specific technical data Type Photometric code Forward current Luminous flux at tp rated 1 Typ. intensity at tp rated 1 Beam characteristics Power consumption at tp rated 1 Min. forward voltage at tc 1 Max. forward voltage at ta = -2 C 1 Efficacy at tp rated SLA DC G2 5mm 7lm D SNC 927/ ma 77 lm 2,92 cd W 3. V. V 88 lm/w > 9 SLA DC G2 5mm 7lm D SNC 927/ ma 77 lm 1,5 cd W 3. V. V 88 lm/w > 9 SLA DC G2 5mm 7lm 93 24D SNC 93/ ma 8 lm 3,19 cd W 3. V. V 95 lm/w > 9 SLA DC G2 5mm 7lm 93 36D SNC 93/ ma 8 lm 1,68 cd W 3. V. V 95 lm/w > 9 SLA DC G2 5mm 7lm 9 24D SNC 9/ ma 89 lm 3,38 cd W 3. V. V 11 lm/w > 9 SLA DC G2 5mm 7lm 9 36D SNC 9/ ma 89 lm 1,78 cd W 3. V. V 11 lm/w > 9 SLA DC G2 5mm 12lm D SNC 927/ ma 1,1 lm 4,3 cd W 32.4 V 37.6 V 93 lm/w > 9 SLA DC G2 5mm 12lm D SNC 927/ ma 1,1 lm 2,2 cd W 32.4 V 37.6 V 93 lm/w > 9 SLA DC G2 5mm 12lm 93 24D SNC 93/ ma 1,17 lm 4, cd W 32.4 V 37.6 V 96 lm/w > 9 SLA DC G2 5mm 12lm 93 36D SNC 93/ ma 1,17 lm 2,3 cd W 32.4 V 37.6 V 96 lm/w > 9 SLA DC G2 5mm 12lm 9 24D SNC 9/ ma 1,27 lm 4,8 cd W 32.4 V 37.6 V 14 lm/w > 9 SLA DC G2 5mm 12lm 9 36D SNC 9/ ma 1,27 lm 2,5 cd W 32.4 V 37.6 V 14 lm/w > 9 1 Tolerance range for optical and electrical data: ±1 %. Colour rendering index CRI 2

3 1. Standards EN 6231 EN EN Photometric code Key for photometric code, e. g. 93 / st digit 2 nd + 3 rd digit 4 th digit 5 th digit 6 th digit Luminous flux after 25% Code CRI McAdam after of the life-time (max.h) Colour temperature in McAdam 25% of the Code Luminous flux initial life-time 7 7 % Kelvin x (max.h) 8 8 % % 1.2 Energy classification 3. Installation / wiring 3.1 Electrical supply/choice of LED Driver SLA modules from Tridonic are not protected against overvoltages, overcurrents, overloads or short-circuit currents. Safe and reliable operation can only be guaranteed in conjunction with a LED Driver which complies with the relevant standards. The use of LED Drivers from Tridonic in combination with SLA modules guarantees the necessary protection for safe and reliable operation. If a LED Driver other than Tridonic is used, it must provide the following protection: Short-circuit protection Overload protection Overtemperature protection SLA modules must be supplied by a constant current LED Driver. Operation with a constant voltage LED Driver will lead to an irreversible damage of the module. Wrong polarity can damage the SLA. Type Energy classification SLA DC G2 5mm 7lm 927 SNC A+ SLA DC G2 5mm 7lm 93 SNC A+ SLA DC G2 5mm 7lm 9 SNC A++ SLA DC G2 5mm 12lm 927 SNC A+ SLA DC G2 5mm 12lm 93 SNC A+ SLA DC G2 5mm 12lm 9 24D SNC A++ SLA DC G2 5mm 12lm 9 36D SNC A+ 3.2 wiring 2. Thermal details 2.1 tp point, ambient temperature and life-time The temperature at tp reference point is crucial for the light output and life-time of a LED product. For SLA DC G2 7lm a tp temperature of C and for SLA DC G2 12lm a tp temperature of 75 C has to be complied in order to achieve an optimum between light output and life-time. Compliance with the maximum permissible reference temperature at the tc point must be checked under operating conditions in a thermally stable state. The maximum value must be determined under worst-case conditions for the relevant application. Red: + Black: 3.3 Wiring type and cross section Cable type: VDE HO3VVH2-F.5 mm² Cable length: 4 mm Stripping length: 8 mm, pre-tinned The tc and tp temperature of LED modules from Tridonic are measured at the same reference point. 2.2 Storage and humidity storage temperature C L N red... black Operation only in non condensing environment. Humidity during processing of the module should be < 85 %. LED Driver 2.3 Thermal design and heat sink The rated life of LED products depends to a large extent on the temperature. If the permissible temperature limits are exceeded, the life of the SLA will be greatly reduced or the SLA may be destroyed. 3

4 3.4 Mounting instruction 3.5 EOS/ESD safety guidelines >7 / 8 / 7 > ø49,6 tc, tp 5 The device / module contains components that are sensitive to electrostatic discharge and may only be installed in the factory and on site if appropriate EOS/ESD protection measures have been taken. No special measures need be taken for devices/modules with enclosed casings (contact with the pc board not possible), just normal installation practice. For further information for EOS/ESD safety guidlines and the ESD classification please refer to the brochure entitled For mounting the SLA products it is necessary to have a assemble ring which is not provided. Chemical substance may harm the LED module. Chemical reactions could lead to colour shift, reduced luminous flux or a total failure of the module caused by corrosion of electrical connections. 4. Life-time 4.1 Life-time, lumen maintenance and failure rate The light output of an LED Module decreases over the life-time, this is characterized with the L value. L7 means that the LED module will give 7 % of its initial luminous flux. This value is always related to the number of operation hours and therefore defines the life-time of an LED module. As the L value is a statistical value and the lumen maintenace may vary over the delivered LED modules. The B value defines the amount of modules which are below the specific L value, e.g. L7B1 means 1 % of the LED modules are below 7 % of the inital luminous flux, respectivly 9 % will be above 7 % of the initial value. n addition the percentage of failed modules (fatal failure) is characterized by the C value. The F value is the combination of the B and C value. That means for F degradation and complete failures are considered, e.g. L7F1 means 1 % of the LED modules may fail or be below 7 % of the initial luminous flux. 4.2 Lumen maintenance SLA DC 7lm: Forward current tp temperature L9B5 L9B1 L8B5 L8B1 L7B5 L7B1 18 ma 25 ma 5 C 14, h 8, h 31, h 25, h >5, h 42, h 65 C 14, h 8, h 31, h 25, h >5, h 42, h C 14, h 8, h 31, h 25, h >5, h 42, h 75 C 13, h 8, h 31, h 25, h >5, h 42, h SLA DC 12lm: Forward current tp temperature L9B5 L9B1 L8B5 L8B1 L7B5 L7B1 25 ma 35 ma 55 C >5, h >5, h >5, h >5, h >5, h >5, h 7 C >5, h >5, h >5, h >5, h >5, h >5, h 75 C >5, h >5, h >5, h >5, h >5, h >5, h 9 C >5, h >5, h >5, h >5, h >5, h >5, h 4

5 5. Photometric charcteristics 5.1 Coordinates and tolerances according to CIE 1931 The specified colour coordinates are measured integral in thermal saturated stage at tp rated. The ambient temperature of the measurement is ta = 25 C. The measurement tolerance of the colour coordinates are ±.1. Module type Current impulse tp rated SLA DC G2 7lm 25 ma C SLA DC G2 12lm 35 ma 75 C 2,7 K x y Centre SLA DC G2 7lm Centre SLA DC G2 12lm ,42,418,41,41,412,41,8,, norm. intensity [%] 1 8 2,2,45,4515,453,4545,45,4575 MacAdam ellipse: 3SDCM,459,45,462,4635, wave length [nm] 3, K x y Centre SLA DC G2 7lm Centre SLA DC G2 12lm ,41,412,41,8,,,2,,398 norm. intensity [%] 1 8 2,39,39,427,4285,43,4315,433,4345 MacAdam ellipse: 3SDCM,43,4375,439,45, wave length [nm] 5

6 4, K x y Centre SLA DC G2 7lm Centre SLA DC G2 12lm ,392,39,388,38,38,382,38,378,37 norm. intensity [%] 1 8 2,37,372,375,3765,378,3795,381,3825 MacAdam ellipse: 3SDCM,38,3855,387,3885, wave length [nm] 5.2 Light distribution Light distribution for 24D Light distribution for 36D relative intensity [%] relative intensity [%] Relative luminous flux vs. tp temperature SLA DC G2 5mm 7lm 9xx SNC 1,1 1,5 rel. luminous flux 1,,95, tp [ C] 6

7 SLA DC G2 5mm 12lm 9xx SNC 1,1 1,5 rel. luminous flux 1,,95, tp [ C] 6. Miscellaneous 6.1 Additional information Additional technical information at Technical Data Guarantee conditions at Services Life-time declarations are informative and represent no warranty claim. 7