Target cell RTD-set. RTD label. Epics RTD notation. Red or Golden. CPC plug slot. Old notation from 1 to 15** RTD 4, B4, R2.

Transcription

1 Target cell -set The -set for the target cell consists of 7 temperature sensors which are attached to distinct locations of the target cell (as shown on the photo above with a GEn-cell with a small pumping chamber -at the W&M lab where we use only 6 s). Every temperature sensor (or = resistance temperature detector) has 2 leads. Each lead is connected to 2 wires. The wires of one lead are labeled either as red or golden depending on to which one of the leads they are soldered. The 1.5m wires of the -set are connected with a CPC-plug to a 6m extension cable which uses a D-sub(miniature) plug as connection to the roughly 30m long wires toward the read-out electronic. The 30m wires are still labeled in two former s: At some point 14 single s with only 2 wires each (instead of 4 like here) have been used. Each of those 14 -cables consists of one red wire and one black wire combined by a grey insulation which is labeled from 1 to 15 (without the number 13). The slots of the read-out electronic refer to these labels, e.g. 10, B2, R4 means the black wire of 10 goes into the 2nd slot and the red wire goes into the 4th slot. Another old system combines two of those grey wires and labels the couples from 1 to 7 (but this order is different than the here used -labels from A to G or the Epics-system from 1 to 7). The D-sub is a substitute for an Amphe-Lite that was used in the year 2000 and is not being produced anymore. To achieve a complete map all pin assignments (also the former ones) are given in the following table: Epics label 6 A CPC plug slot or 1 2 6m extension cable* from 1 to 15** 4, B4, R2 Black (orange) Yellow (black) 3, from 1 to 7 2 D-sub Former Amphe-Lite 1 F 20 G 1 of 6 3/26/06 2:04 PM

2 3 4 4 F 5 6 A 6 7 B 4 F 5 G 7 B 3 E 5 G 1 C 3 E D Black (yellow) (pink) 14, Pink B1, R3 Orange 4, (black) B4, R2 (orange) 5, Orange B2, R4 Pink (white) 15, White B2, R4 (pink) Black 1, B1, R3 (black) (brown) 6, Brown B1, R3 Blue (pink) 11, Pink B3, R1 (blue) Blue (black) 2, Black B2, R4 (blue) (white) 8, White B2, R4 Pink (yellow) 12, Yellow B4, R2 (pink) Pink 10, (brown) B2, R4 (blue) 7, Blue 21 H 17 d 7 16 c 2 2 Y 3 L 3 4 M 34 a 7 35 b 36 C 1 37 D 22 J 3 23 K 13 e 6 14 f 18 A 1 19 B 6 S 4 7 R 31 g 6 32 h 5 9 T 25 P 4 26 N 2 of 6 3/26/06 2:04 PM

3 B1, R3 C Brown 10, U (pink) B2, R4 Pink 2 D V (orange) 9, Orange B1, R W (pink) * The first color is the color of the wire that is used. The color in brackets is the color of its partner-wire, means the 2 nd wire in the 2-wire-insulation. ** Example: 10, B2, R4 means the black wire of 10 goes into the 2 nd slot and the red wire goes into the 4 th slot. At the read-out electronic the s are ordered from the left side to the right side as follows: 10 & 9, 12 & 11, 4 & 3, 8 & 7, 2 & 1, 5 & 6, 15 & 14. PIN-Assignment of the CPC-plug Reverse sex plug for pin contacts, shell size 17, 28 contacts, Allied Stk # , Manufacturer s part # and Reverse sex free hanging receptor for socket contacts, shell size 17, 28 contacts, Allied Stk # , Manufacturer s part # Contacts size 20-DF Pin, solder cup type (18 AWG max. wire), Allied Stk# , Manufacturer s part # and Contacts size 20-DF Socket, solder cup type (18 AWG max. wire), Allied Stk# , Manufacturer s part # PIN-Assignment of the D-sub Amphenol 960, female: , male: , 37 contacts PIN-Assigment of the Amphe-Lite that was formerly used Connector AL06F19-32S (IP), Amphenol Industrial Operations Straight plug, size 19 Insert arrangement: 19-32, service rating: I, number of contacts: 32, contact size: 20 crimp socket Allied electronics stocking number: of 6 3/26/06 2:04 PM

4 Socket contacts, size 20: Newark stocking number Reference cell -set The -set for the reference cell consists of 3 temperature sensors. It is built in the same style as the target cell -set and has also a length of 1.5 meters. The 30m wires of the reference cell s toward the red-out electronics are also labeled in two former s: There are 6 grey cables (with each a red and a black wire) labeled from 1 to 6. And these are combined into three couples with the numbers 8, 9 and 10. Epics label 8 K 10 M 9 L 10 M 9 L CPC plug slot or 1 Pink 6m extension cable from 1 to 6 3, B1, R2 from 8 to 10 D-sub Former Amphe-Lite Grey 4, Lilac B3, R Beige 3, 2 13 B1, R2 15 5, White B1, R , Black R1, B Orange 6, Blue B4, R Brown 1, Yellow B3, R of 6 3/26/06 2:04 PM

5 PIN-Assignment of the CPC-plug Reverse sex plug for pin contacts, shell size 17, 28 contacts, Allied Stk # , Manufacturer s part # and Reverse sex free hanging receptor for socket contacts, shell size 17, 28 contacts, Allied Stk # , Manufacturer s part # Contacts size 20-DF Pin, solder cup type (18 AWG max. wire), Allied Stk# , Manufacturer s part # and Contacts size 20-DF Socket, solder cup type (18 AWG max. wire), Allied Stk# , Manufacturer s part # PIN-Assignment of the D-sub Amp 9420, , 15 contacts PIN-Assigment of the Amphe-Lite that was formerly used Connector AL06F11-35S (IP), Amphenol Industrial Operations Straight plug, size 11 Insert arrangement: 11-35, service rating: M, number of contacts: 13, contact size: 22D crimp socket Allied electronics stocking number: Newark stocking number: 34C9255 Socket contacts, size 22D: Newark stocking number More information about the former wiring: designation wires pinout adc channels screen YF(4) GH(3) 5 of 6 3/26/06 2:04 PM

6 JK(6) LM(5) NP(7) RS(8) TU(10) VW(9) ef(11) gh(12) ab(15) cd(14) AB(2) CD(1) ,13(11) 3,12(12) (1) 6,7(2) 8,9(5) ,11(6) From 6 of 6 3/26/06 2:04 PM