Installation Instruction for USB Interface
|
|
- Phoebe Baldwin
- 6 years ago
- Views:
Transcription
1 Installation Instruction for USB Interface A AMI Option USB Interface V1 and A AMI Option USB Interface V2 Analytical Instruments SWAN ANALYTISCHE INSTRUMENTE AG, CH-8340 Hinwil TEL , FAX USB Interface installation /16 1
2 Compatibility CAUTION Risk of damage to the equipment Please observe the compatibility notes below. Interface version Function Requirement A ) USB support Mainboard 2.0 to 2.4 Firmware V5.00 or higher A USB support Mainboard 2.0 or higher Firmware V5.00 or higher USB support & 2) Mainboard 2.5 2) 3 rd signal output Firmware V6.00 or higher 1) Do not use with mainboard 2.5 (causes short circuit) 2) Can be operated parallel, requires mainboard 2.5 and firmware 6.00 USB Interface installation /16 2
3 USB Interface Installation Overview CAUTION Observe precautions for handling electrostatic discharge sensitive devices. The installation kit contains an USB interface [A] and a USB stick [B]. It can be used: as data logger for firmware upload A USB interface PCB B USB stick USB Interface installation /16 3
4 Install the USB Interface WARNING! Electrical shock hazard Before opening the AMI Transmitter switch power off. A USB interface B USB stick C USB socket D Plug E Transmitter housing F Mainboard To install the USB interface proceed as follows: 1. Switch power off. Depending on your application stop operation according to chapter Stop of Operation for Maintenance in the manual. 2. Open the transmitter housing. 3. Insert the USB interface with the plug [D] facing towards the mainboard [F] into the slot. 4. Insert the USB stick [B] into the USB socket [C]. 5. Close the transmitter housing. 6. Switch power on. The USB stick is recognized automatically. USB Interface installation /16 4
5 After the USB stick has been installed, in the firmware the following two menus are added: Main Menu Operation Logger Log Interval 30 Minutes Clear Logger no Eject USB Stick <Enter> Main Menu Installation Interface Protocol USB Stick Status LEDs and Operating Elements A B USB stick C USB socket D E G The push-button (G) has the following two functions, if it is pressed down: the calibration history and the event history are copied to the USB stick the USB stick will be deactivated. H The blue LED is on if the USB stick is installed and ready to record data. The blue LED is off if the function <Eject USB stick> has been activated or the pushbutton has been pressed. I LED 1 (green) is blinking during the internal installation sequence of the USB Interface J LED 2 (green) is blinking if the USB stick is active is steady on if the USB stick is ejected but remains in the socket. Is off if the USB stick is removed from its socket USB Interface installation /16 5
6 Remove the USB Stick To remove the USB stick proceed as follows: Variant 1 with power interruption (recommended) 1. Navigate to menu Operation/Logger. 2. Select <Eject USB stick> and press <Enter> (Details see p. 6, Read Logger Data). 3. Switch power off. 4. Open the transmitter housing. 5. Press the USB interface [A] down while pulling out the USB stick [B]. Variant 2 without power interruption WARNING! Electrical shock hazard This work may only be performed by trained professionals. Take adequate safety precautions before opening the transmitter housing 1. Open the transmitter housing. 2. Press the push-button [G] on the USB interface. 3. Wait until the blue LED is switched off. 4. Press the USB interface [A] down while pulling out the USB stick [B]. USB Interface installation /16 6
7 Read Logger Data To read the logger data from the USB stick proceed as follows: 1. Remove the USB stick from the AMI transmitter. Proceed according to section Remove USB Stick, Variant 1 on page 6. Note: The function <Eject USB stick> has the following effect: the calibration history and the event history are copied to the USB stick the logger file will be completed (next time the USB stick is inserted a new logger file will be created). the USB stick will be deactivated 2. Insert the UBS stick into the USB socket of your notebook or PC. Depending on the Firmware there are 3 or more txt files which contain the logger data. For example: Event history Calibration history Logger data 3. Copy the files to your notebook or PC. 4. Remove the USB stick and insert it into the USB interface of the AMI transmitter again Load Firmware To install a Firmware update from the USB stick proceed as follows: 1. Write down all customer-specific firmware settings (parameters for instrument operation, configuration of signal outputs and relays etc.) 2. Download the logger data to the USB stick using the function <Eject USB stick> in the menu Operation/Logger. 3. Remove the USB stick from the AMI transmitter. Proceed according to section Remove USB Stick on page Leave the transmitter switched off. 5. Insert the USB stick into the USB socket of your notebook or PC. 6. Copy all files you need ( aout.a37 ; *.hex) to the root directory of the USB stick. 7. Remove the USB stick from the USB socket of your notebook or PC 8. Insert the USB stick into the USB interface of the AMI transmitter again. 9. Close the transmitter housing. 10. Switch power on. 11. Press <Enter> and navigate to <Installation> Main Menu 5 Messages Diagnostics Maintenance Operation Installation USB Interface installation /16 7
8 12. Press <Enter> and navigate to <Miscellaneous>. Installation 5.4 Sensors Signal Outputs Relay Contacts Misscellaneous Interface 13. Press <Enter> and navigate to <Load Firmware>. Miscellaneous Language Set defaults Load Firmware Password English no no Sample ID 14. Press <Enter> and select yes. Miscellaneous Language Load Firmware English Set defaults no no Load Firmware yes no Password Sample ID 15. Conform with <Enter>. The Firmware update starts. With this method the firmware of the AMI transmitter is updated with all files, located in the root directory of the USB stick, which have the file extension <.a37> or <.hex>. After the update has been finished: 17. Navigate to <Installation> <Miscellaneous> <Set defaults>. 18. Press [Enter] and select <completely>. 19. Press [Enter], [Exit] and confirm with <Yes>. The AMI transmitter restarts and all settings are set to the default values. 20. Enter the customer-specific settings according to the notes taken In step 1. USB Interface installation /16 8
BP Brine Pro Brine Maker Software Update. Installation Instructions. Original Instructions CAUTION
October 10, 2017 Lit. No. 11833, Rev. 01 BP-2000 Brine Pro Brine Maker Software Update Installation Instructions Original Instructions CAUTION Read the Owner's Manual before installing or operating the
More informationSIMATIC. Industrial PC SIMATIC Panel PC 477B. Operating Instructions (Compact) 05/2007 A5E
SIMATIC Industrial PC Operating Instructions (Compact) 05/2007 A5E01023488-01 Trademarks Disclaimer of Liability All names identified by are registered trademarks of the Siemens AG. The remaining trademarks
More informationR&S ZN-Z15x Calibration Units User Manual
R&S ZN-Z15x Calibration Units User Manual (=UÉÍ2) Version 02 User Manual 1337596302 This User Manual describes the following R&S ZN-Z15x models: R&S ZN-Z150, N (f), 2 ports, 5 khz to 6 GHz (1335.6710.72)
More informationQUICK START USER GUIDE. Data Logger Model L452
QUICK START USER GUIDE Data Logger Model L452 Statement of Compliance Chauvin Arnoux, Inc. d.b.a. AEMC Instruments certifies that this instrument has been calibrated using standards and instruments traceable
More informationPhase Loss Protection Upgrade. Phase Loss Protection Upgrade. In this bulletin:
Phase Loss Protection Upgrade In this bulletin: Introduction... 2 Purpose... 2 General... 2 Applicability... 2 HD3070 Phase Loss Protection Upgrade Kit Parts... 2 Preparation... 4 Install the Phase Loss
More informationR&S ZN-Z5x Calibration Units User Manual
R&S ZN-Z5x Calibration Units User Manual (=UÉÇ2) User Manual 1337.5957.02 01 This User Manual describes the following models: R&S ZN-Z50, 3.5 mm (f), 2 ports, 9 khz to 9 GHz (1335.6904.30) R&S ZN-Z50,
More informationTechnical User Manual Avisaro 4.0 Product Series
Technical User Manual Avisaro 4.0 Product Series including PC Companion Software RS232 CAN 4..20mA Analog Version / Date 2019-01-11 1. TABLE OF CONTENT Hint: Use key with mouse click within the
More informationTCM-4 Data Logger Battery Replacement Instructions
TCM-4 Data Logger Battery Replacement Instructions These instructions apply to the following product: TCM-4 Shallow Water Current Meter These instructions assume that the user has purchased a TCM-4 Battery
More informationGetting started - USW 3.x Software download from internet Software installation Device setup Data backup
MULTI-LINE 2 APPLICATION NOTES Getting started - USW 3.x Software download from internet Software installation Device setup Data backup DEIF A/S Frisenborgvej 33 DK-7800 Skive Tel.: +45 9614 9614 Fax:
More informationDATA LOGGER (Version V1.3)
WYLER AG Im Hölderli CH-8405 WINTERTHUR Switzerland Tel. 0041 (0) 52 233 66 66 Fax. 0041 (0) 52 233 20 53 Homepage: http://www.wylerag.com E-Mail: wyler@wylerag.com Operating instructions DATA LOGGER (Version
More informationManual. VIPA Accessories USB-MPI adapter 950-0KB31. Order No.: VIPA HB158E_PC-AG Reference: RE_950-0KB31 Rev. 08/25
Manual VIPA Accessories USB-MPI adapter 950-0KB31 Order No.: VIPA HB158E_PC-AG Reference: RE_950-0KB31 Rev. 08/25 This manual is relevant for: Product Order number as of state: HW SW USB-MPI adapter VIPA
More informationUser Manual. HOPPECKE sun powerpack premium. service software
User Manual HOPPECKE sun powerpack premium service software Contents 1. INTRODUCTION 4 2. TARGET GROUP 4 3. MEANS OF REPRESENTATION 4 4. BASIC INFORMATION FOR APPLICATION USE 5 4.1. System requirements
More informationGetting Started Guide
Getting Started Guide DESKTOP Welcome to LumenX Programming Engine Desktop Model The LumenX Desktop is Data I/O s desktop version programming engine. Designed for programming first-article builds to validate
More informationType ME43. Quickstart
Type ME43 Fieldbus gateway büs to Industrial Ethernet, PROFIBUS DPV1, CC-Link Feldbus-Gateway büs zu Industrial Ethernet, PROFIBUS DPV1, CC-Link Passerelle bus de terrain büs vers Ethernet industriel,
More informationELSETA IOMOD 8DI8DO. User manual. Elseta 3/2017 V1.0
ELSETA User manual Elseta 3/2017 V1.0 COPYRIGHTS AND TRADEMARKS Elseta is UAB Aedilis trademark that identifies UAB Aedilis manufactured products. All of the products copyright belongs to "Aedilis. These
More informationDICKEY-JOHN GAC 2500-UGMA PRODUCT CALIBRATION DOWNLOAD
DICKEY-JOHN GAC 2500-UGMA PRODUCT CALIBRATION DOWNLOAD Product calibration files are located at the DICKEY-john website for loading to the GAC 2500-UGMA Grain Moisture Analyzer. If a USB memory device
More informationMicroTech II McQuay Maverick II Rooftop Unit Controller BACnet Communication Module, Ethernet or IP
Installation and Maintenance Manual IM 853 Group: Controls Part Number: IM 853 Date: June 2007 Supercedes: New MicroTech II McQuay Maverick II Rooftop Unit Controller BACnet Communication Module, Ethernet
More informationSIMPLY PRECISE USER MANUAL. ADJUSTMENT TOOL For NUMERIK JENA Encoders with Online Compensation
USER MANUAL ADJUSTMENT TOOL For NUMERIK JENA Encoders with Online Compensation 2 Index 1. Features and Applications... 3 1.1 Functions of the ADJUSTMENT TOOL... 3 1.2 Dynamic Offset and Amplitude Control
More informationAthlon4 Firmware Update Procedure by USB Memory (FIRMWARE1/FIRMWARE2/FIRMWARE3/FIRMWARE4) Rev.3.0
Athlon4 Firmware Update Procedure by USB Memory (FIRMWARE1/FIRMWARE2/FIRMWARE3/FIRMWARE4) Rev.3.0 Read This Manual Before Attempting Firmware Update This manual describes the procedure for updating firmware
More informationPF31XX FAMILY FIRMWARE UPDATE GUIDE. v1.2 Revised Nov 29, 2016
PF31XX FAMILY FIRMWARE UPDATE GUIDE Revised Table of Contents 1 Overview... 1 2 Firmware Update Process... 2 3 Document Revision History... 5 Page i 1 Overview This document will assist a user in completing
More informationUser Manual. EDK 400J EnOcean Developer Kit
User Manual EDK 400J EnOcean Developer Kit EDK 400J User Manual Important Notes This information describes the type of component and shall not be considered as assured characteristics. No responsibility
More informationSingle Use USB Data Logger EBI 330-T30 / EBI 330-T85. User Manual
Single Use USB Data Logger EBI 330-T30 / EBI 330-T85 User Manual Table of contents Overview... 3 Safety instructions... 5 Unpacking / Package Contents... 6 Configuration... 7 Start / Stop... 8 LEDs...
More informationFirmware Update with SD Card SUNNY BOY WINDY BOY SUNNY TRIPOWER
Firmware Update with SD Card SUNNY BOY WINDY BOY SUNNY TRIPOWER Technical Description NG_UpdSD-TB-TEN114530 Version 3.0 EN SMA Solar Technology AG Table of Contents Table of Contents 1 Information on
More informationAG-HPX300 series Software (Firmware) update procedure
AG-HPX300 series Software (Firmware) update procedure 1. Version Information AG-HPX300 series update procedure 6/24/2009 1-1. Use P2 Status Logger Please use "P2 Status Logger" application software for
More informationData logger. Installation and operating instructions. Read carefully before installation, commissioning and operation.
Data logger Installation and operating instructions SOREL Connect Read carefully before installation, commissioning and operation 1.1. - Specifications Description of data logger Electrical specifications:
More informationSimple Logger II Series
Simple Logger II Series Quick Start Guide ENGLISH www.aemc.com CHAUVIN ARNOUX GROUP Statement of Compliance Chauvin Arnoux, Inc. d.b.a. AEMC Instruments certifies that this instrument has been calibrated
More informationAgilent E4418/19A Power Meter Hardware Upgrade Kit
Agilent E4418/19A Power Meter Hardware Upgrade Kit (E9300 Compatible) Installation Guide Agilent Technologies Notices Agilent Technologies, Inc. 2009 No part of this manual may be reproduced in any form
More informationMulti-Loader. User manual 06/ BBV48778
Multi-Loader User manual 06/2009 BBV48778 www.schneider-electric.com Contents Important information 4 Before you begin 5 Documentation structure 6 Setup procedure 7 Introduction 8 Receipt of the Multi-Loader
More informationMicroTech II McQuay Maverick II Rooftop Unit Controller BACnet Communication Module (MS/TP)
Installation and Maintenance Manual IM 852-2 Group: Controls Part Number: IM 852 Date: January 2008 Supercedes: IM 852-1 MicroTech II McQuay Maverick II Rooftop Unit Controller BACnet Communication Module
More informationInstallation of Firmware Updates on H-2221 GOES Transmitters
Technical Note H-5221 Firmware Update D117 November 2, 2018 Installation of Firmware Updates on H-2221 GOES Transmitters INTRODUCTION The intent of this document is to provide WaterLOG H-2221 GOES transmitter
More informationJUMO dtrans T02. programmable. transmitter. B Operating Instructions 5.00/
JUMO dtrans T02 programmable transmitter B 95.6521 Operating Instructions 5.00/00380664 Overview of operation JUMO dtrans T02 Standard accessory 1 Type designation (1) Basic version 956521 programmable
More informationPX Series Balances. Quick Start Guide. Please download the user manual from
Scan QR Code with your WebCam for downloading the user instruction manual. PX Series Balances Quick Start Guide Please download the user manual from www.ohaus.com. EN-1 1. INSTALLATION 1.1 Select the
More informationTraining Sales Support
PO Box 940 BLACKWOOD SA 5051 www.automationdistributors.com.au Installation Instructions for Omni Z-Wave Interface Plugin for Vera Controllers UI7 Serial Connection Kit Thank you for purchasing the Omni
More informationVS Omni. Consumer How-To Guide. CTSG-VSO100a. Copyright 2018 Hayward Industries Inc.
VS Omni Consumer How-To Guide CTSG-VSO100a Copyright 2018 Hayward Industries Inc. Safety Precautions Warning! High Voltage Electrocution Hazard Hazardous voltage can shock, burn, cause serious injury and
More informationPowerMonitor 5000 Unit Catalog Number Upgrade
Installation Instructions PowerMonitor 5000 Unit Catalog Number Upgrade Catalog Numbers 1426-MxE-xxx Topic Page Upgrade the Device Catalog Number with the ControlFLASH Utility 3 Determine Communication
More informationAdventurer TM Balances
Scan QR Code with your WebCam for downloading the user instruction manual. Adventurer TM Balances Quick Start Guide Please download the user manual from www.ohaus.com. 1. ASSEMBLY 1) Unpack the balance
More informationVeritas Appliance Hardware Service Procedure
Veritas Appliance Hardware Service Procedure Power Supply Replacement: NetBackup 5220 Appliance Document Number: 112 Version: 3.0 (10/03/15) Purpose This document describes the process for replacing a
More informationFC-11 FIELD COMMUNICATOR 1.54 INSTRUCTION MANUAL. IM-EN-FC11 Version 1.13
FC-11 FIELD COMMUNICATOR 1.54 INSTRUCTION MANUAL IM-EN-FC11 Version 1.13 Table of contents 1 Description............................................................ 1 1.1 Kit contents....................................................
More informationAn ISO 9001 Company. BOP 1KW-MG FIRMWARE RETROFIT KIT
INSTRUCTION MANUAL 1. DESCRIPTION KEPCO An ISO 9001 Company. BOP 1KW-MG FIRMWARE RETROFIT KIT BOP 1KW-MG RETROFIT KIT 219-0621 Kepco KIT 219-0621-(n) contains the parts used to upgrade the firmware for
More informationOPT2041. Fiber Optic Cable Sensor. Operating Instructions. Available as PDF only Status:
OPT2041 Fiber Optic Cable Sensor Operating Instructions Available as PDF only Status: 18.06.2018 www.wenglor.com Index 1. Proper Use 3 2. Safety Precautions 3 3. General Information Regarding the Device
More informationDALI Professional Controller-4. Control unit Operating instructions
LI Professional Controller-4 Control unit Operating instructions Contents Safety... 4 General instructions 4 Safety instructions 4 Description... 5 Purpose and application 5 Configuration 5 Design 5 Connections
More informationAG-UX180/UX170 Firmware update procedure
AG-UX180/UX170 Firmware update procedure 1. Version display method 1-1. The version of system in camera recorder The version of system in this camera recorder is displayed in MAINTENANCE menu screen. 1.
More informationCONFIGURATION HANDBOOK BGL144
PROGRAMMABLE BARGRAPH CONFIGURATION HANDBOOK BGL144 BGL172 LOREME 12, rue des Potiers d'etain Actipole BORNY - B.P. 35014-57071 METZ CEDEX 3 Phone 03.87.76.32.51 - Telefax 03.87.76.32.52 Contact : Commercial@Loreme.fr
More informationUser Manual EDK 350 Developer Kit EDK 352 Thermo Developer Kit (EDK 350 upgrade) EPK 350 Programmer Kit (ESK 300 upgrade)
User Manual EDK 350 Developer Kit EDK 352 Thermo Developer Kit (EDK 350 upgrade) EPK 350 Programmer Kit (ESK 300 upgrade) EDK 350 / EDK 352 / EPK 350 User Manual Important Notes This information describes
More informationAn ISO 9001 Company. BOP 1KW-MG FIRMWARE RETROFIT KIT
INSTRUCTION MANUAL 1. DESCRIPTION KEPCO An ISO 9001 Company. BOP 1KW-MG FIRMWARE RETROFIT KIT BOP 1KW-MG RETROFIT KIT 219-0597 Kepco KIT 219-0597 contains the PROMs used to upgrade the firmware for BOP
More informationPower Xpert Meter 2000 Gateway Card Kit
Quick Start Guide IL02601011E Rev. 2 December 2011 PXM 2250 PXM 2260 IQ 250 IQ 260 Power Xpert Meter 2000 Gateway Card Kit Table of Contents Remove the Meter From Service.... 2 Disconnect Power Connections,
More informationPower Xpert Meter 2000 Gateway Card Kit
Quick Start Guide IL02601011E PXM 2250 PXM 2260 IQ 250 IQ 260 Power Xpert Meter 2000 Gateway Card Kit Table of Contents Remove the Meter From Service... 2 Disconnect Power Connections, CTs, and Modbus....
More informationOPT2011. High-performance distance sensor. Operating Instructions
OPT2011 High-performance distance sensor Operating Instructions Status: 15/07/2013 2 Table of Contents 1. Use for Intended Purpose 4 2. Safety Precautions 4 2.1. Safety Precautions 4 2.2. Laser/LED warning
More informationGSM HOME SECURITY SYSTEM
Cell /Mobile phone home security system GSM HOME SECURITY SYSTEM Model : BS120 TABLE OF CONTENTS 1. FEATURES... 1 2. APPLICATION... 2 3. SPECIFICATIONS... 3 4. FRONT PANEL & LAYOUT DESCRIPTION...6 5. BASIC
More informationUser Guide File Transfer Scheduler. LINAX Series LINAX A310 CAMILLE BAUER
LINAX Series User Guide File Transfer Scheduler CAMILLE BAUER LINAX A310 Use of Instructions Warning. An instruction that draws attention to the risk of injury or death. Note. Clarification of an instruction
More informationWEA-Base. User manual for load cell transmitters. UK WEA-Base User manual for load cell transmitters Version 3.4 UK
WEA-Base User manual for load cell transmitters 1 Contents 1. Technical data... 3 2. Assembly... 4 2.1 Power supply... 4 2.2 Load cells... 4 2.3 RS-485... 4 2.4 Relays... 5 2.5 Digital input... 5 2.6 Analogue
More informationUpgrading a 1000 Series Printer with MagicLoader
Upgrading a 1000 Series Printer with MagicLoader Header Videojet Technologies, Inc. Knowledge Article Article Number 000005892 Procedure Upgrading a Printer with MagicLoader Notice MagicLoader software
More informationUser s Guide. for egfx Breakaway Box and egfx Breakaway Box 550 Thunderbolt 3 to egpu PCIe Card Expansion Systems. For Windows
User s Guide for egfx Breakaway Box and egfx Breakaway Box 550 Thunderbolt 3 to egpu PCIe Card Expansion Systems For Windows Contents 1 Introduction, Compatibility Information, and Setup Overview 1 Introduction
More information99 Washington Street Melrose, MA Phone Toll Free Visit us at
99 Washington Street Melrose, MA 02176 Phone 781-665-1400 Toll Free 1-800-517-8431 Visit us at www.testequipmentdepot.com Table of Contents 1. General Safety Requirements... 1 2. Safety Terms and Symbols...
More informationPacketBand TDM-4 Quickstart Guide V3.2
2012 Patapsco Designs Ltd Patapsco has recently been acquired by Communications Systems, Inc. (CSI) and is now a part of Transition Networks, Inc., a subsidiary of CSI. The high-quality, reliable Transition
More informationUpdating Firmware for Selected Cameras with Location Data Support
Updating Firmware for Selected Cameras with Location Data Support Thank you for choosing a Nikon product. This guide describes how to update the firmware for the following cameras with location data support:
More informationBlue Box BLUE BOX TM LTD PARTS REPLACEMENT GUIDE
Blue Box BLUE BOX TM LTD PARTS REPLACEMENT GUIDE WARNINGS 1. All servicing should be performed by qualified service personnel. 2. WARNING, Battery may explode if mistreated. Do not recharge, disassemble
More informationPROFIsafe SITRANS. Pressure transmitter SITRANS P, DS III PROFIsafe series. Product Information 7MF4*34 04/2008 A5E
1 SITRANS Pressure transmitter SITRANS P, DS III PROFIsafe series Product Information 7MF4*34 04/2008 A5E00732533-02 Safety Guidelines This manual contains notices you have to observe in order to ensure
More informationGathering Logs from Polycom RealPresence Group Series System and Peripherals
Gathering Logs from Polycom RealPresence Group Series Systems and Peripherals Version 6.1.0 1 Table of Contents Table of Contents... 2 Download or Transfer RealPresence Group System Log Files... 3 Downloading
More informationCRx Printers START-UP GUIDE
CRx Printers START-UP GUIDE To Get Started: Insert the Companion CD shipped with the CRx printer* into the computer. Please refer to the User s Guide included on the CD companion or the Compact Industrial
More informationUser Guide USB Frequency Counter
User Guide USB Frequency Counter UFC-6000 1 to 6000 MHz Input Impedance: 50 Ω Dynamic Range: -28 to +13dBm Important Notice This guide is owned by Mini-Circuits and is protected by copyright, trademark
More informationThermo-Anemometer Data Logger Model 1227
Thermo-Anemometer Data Logger Model 1227 Quick Start Guide ENGLISH www.aemc.com Statement of Compliance Chauvin Arnoux, Inc. d.b.a. AEMC Instruments certifies that this instrument has been calibrated using
More informationDPL4000 Portable Low Range Dew Point Analyzer
OPERATIONS MANUAL DPL4000 Portable Low Range Dew Point Analyzer 7205 Edington Drive / Cincinnati, OH 45249 / Tel (513) 772-0060 / Fax (513) 772-9466 Page #1 of 16 M4581 DPL4000 Product Description: This
More informationConnecting the LCD Race Display via Direct Ethernet Connection
Connecting the LCD Race Display via Direct Ethernet Connection Using the latest version of DataPro and upgrading the firmware on your Stack LCD Motorsport display provides important improvements to the
More informationMaxxyz Compact Retrofit Kit Installation Guide
Maxxyz Compact Retrofit Kit Installation Guide Introduction The new M-Series software and the Windows 7 Embedded OS require that the Maxxyz Compact and Cerebrum modules are upgraded to 2 GB RAM. This Retrofit
More informationMC-12 Software Installation Instructions
MC-12 DOCUMENTATION CONVENTIONS This document contains software installation instructions for the MC-12/MC-12 Balanced. Refer to the MC-12 User Guide for general safety, installation, and operating instructions.
More informationAG-HPX250 series Software (Firmware) update procedure
AG-HPX250 series Software (Firmware) update procedure 1. Version Information Confirm the version number The version number of software is displayed in DIAGNOSTIC menu screen of setting menu. 1. Turn the
More informationM2500 Engine Controller Configuration Manual
M2500 Engine Controller Configuration Manual Revision: 08-04-2011 Page 1 Contents 1 Preface... 4 2 Configuration from front panel... 5 2.1 Engine Controller Configuration... 6 2.1.1 RPM settings... 6 2.1.2
More informationPower Xpert Meter 2000 Gateway Card Kit
Quick Start Guide IL02601011E PXM 2250 PXM 2260 IQ 250 IQ 260 Power Xpert Meter 2000 Gateway Card Kit Table of Contents Remove the Meter From Service.... 2 Disconnect Power Connections, CTs, and Modbus....
More informationAltair RU. Owner s Manual. Document name: AtrRU-EN Document version: 0.3 Release date: 25/03/2009
Altair RU Owner s Manual Document name: AtrRU-EN Document version: 0.3 Release date: 25/03/2009 triadis engineering GmbH Eichholzstrasse 7 Postfach CH-3254 Messen Phone: +41 (0)31 768 15 15 Fax: +41 (0)31
More informationDIVAR IP 2000 DIP N, DIP HD, DIP HD. en Quick Installation Guide
DIVAR IP 2000 DIP-2040-00N, DIP-2042-2HD, DIP-2042-4HD en Quick Installation Guide DIVAR IP 2000 Table of Contents en 3 Table of contents 1 Safety precautions 4 1.1 General safety precautions 4 1.2 Electrical
More informationUser Guide USB Solid State RF Switch
User Guide USB Solid State RF Switch USB-SP4T-63 1 to 6000 MHz Single SP4T switch Important Notice This guide is owned by Mini-Circuits and is protected by copyright, trademark and other intellectual property
More informationRDX QuikStation System Components
RDX QuikStation WHAT S IN THE BOX? 1 2 4 3 8 9 5 6 USB 7 11 12 13 14 10 1. RDX QuikStation 2. North American Region Power Cord 3. European Region Power Cord 4. Ethernet Cables (2 each) 5. End Cap Covers
More informationTransmitter Series M400 / M300 transmitters Extended ISM functions Easy handling Intuitive user interface Multi-parameter
INGOLD Leading Process Analytics Transmitter Series M400 / M300 transmitters Extended ISM functions Easy handling Intuitive user interface Multi-parameter Versatile Transmitter Series For Intelligent Measurement
More informationSHIMPO INSTRUMENTS. FG-7000T Digital Torque Gauge Operation Manual
FG-7000T Digital Torque Gauge Operation Manual SHIMPO INSTRUMENTS Operators should wear protection such as a mask and gloves in case pieces or components break away from the unit under test. Whether the
More informationTSM800 / TSM1330 Update Instructions
TSM800 / TSM1330 Update Instructions Contents Contents... 1 Automatic Updates... 1 Manual Update to the Latest Version of N2KView... 2 Manual Update of the Complete Operating System... 3 Automatic Updates
More informationService tool HENRI. Technical Documentation. Short reference guide for proceeding internal HENRI functions JMo/Roe Version 2.0 KA.
Technical Documentation Service tool HENRI Short reference guide for proceeding internal HENRI functions 06.10 JMo/Roe Version 2.0 KA.HENRI-EN National Rejectors, Inc. GmbH Zum Fruchthof 6 D-21614 Buxtehude
More information(RS232-Interface) The variants with other interfaces look slightly different. Operation
Description Characteristic features Up to 20 temperature measurement points measuring range 55 +125 C Use of temperature probe DALLAS-Sensors type 18B20, 18S20 Three wire, parallel connection of sensors
More informationHIMatrix Safety-Related Controller Maintenance Manual
HIMatrix Safety-Related Controller Maintenance Manual HIMA Paul Hildebrandt GmbH + Co KG Industrial Automation Rev. 1.00 HI 800 455 E All HIMA products mentioned in this manual are protected by the HIMA
More informationQuick-Start Guide. BNS Solutions. QSK62P Plus
BNS Solutions Quick-Start Guide QSK62P Plus RS-232 Port Link LED 8-character x 2-line LCD Expansion Port (2) Reset Switch Power LED Thermistor I/O Ring (4) M16C MCU Analog Adjust Pot MCU Crystal Expansion
More informationDell SCv300 and SCv320 Expansion Enclosure Owner's Manual
Dell SCv300 and SCv320 Expansion Enclosure Owner's Manual Regulatory Model: E03J, E04J Regulatory Type: E03J001, E04J001 Notes, Cautions, and Warnings NOTE: A NOTE indicates important information that
More informationBLUE LOG X-SERIES. Quick Start Guide. Version
BLUE LOG X-SERIES Quick Start Guide Version 20170223 1 DEVICE OVERVIEW 1 LED: Power-supply status 2 LED: Device status 3 LED: Online status 4 USB port 5 Directional pad 6 OK button 7 ESC button 8 Display
More informationQuick Guide. NomaSense or O 2. USB cable. Temperature probe PT100. Short optical fiber
Content NomaSense O 2 NomaSense or O 2 P300 or P6000 oxygen analyzer USB cable USB-Power adapter (5 VDC, min. 1 A) with different connector pieces USB stick including the Datamanager Software Temperature
More informationOne Expert TM. Handheld Manager, version 1.1. User s Guide
One Expert TM Handheld Manager, version 1.1 User s Guide One Expert TM Handheld Manager, version 1.1 User s Guide Notice Every effort was made to ensure that the information in this document was accurate
More informationSPEECH UPGRADE INSTALLATION GUIDE (MODEL 9100)
SPEECH UPGRADE INSTALLATION GUIDE (MODEL 900) TDN 0700-00062 07/2006 CORPORATE HEADQUARTERS: 522 E. RAILROAD STREET LONG BEACH, MS 39560 PHONE: (228) 868-37 FAX: (228) 868-0437 RMA (RETURN MATERIAL AUTHORIZATION)
More informationAgilent InfinityLab Companion
Agilent InfinityLab Companion Technical Note This technical note describes the installation of the Agilent InfinityLab Companion. Contents Install the InfinityLab Companion 2 Transfer License Back From
More informationSystem Firmware Update Instructions for AVIC-5000NEX, AVIC-6000NEX, and AVIC-7000NEX
System Firmware Update Instructions for AVIC-5000NEX, AVIC-6000NEX, and AVIC-7000NEX IMPORTANT Please download and print these firmware update instructions before downloading and installing the firmware
More informationiq DIGITAL PICTURE FRAME iq Digital Picture Frame DPF701SB USER GUIDE
iq Digital Picture Frame DPF701SB USER GUIDE 1 Table of Contents Important Safety Precautions... 3 Cleaning the LCD Screen... 3 Cleaning the Digital Picture Frame... 3 Introduction... 4 What s in the Box...
More informationINSTRUCTIONS TO UPDATE FIRMWARE FOR
INSTRUCTIONS TO UPDATE FIRMWARE FOR Dranetz 1000 New Durham Road, Edison, New Jersey 08818 Telephone 1-800-372-6832 or 732-287-3680 Fax 732-248-1834 www.dranetz.com Updating the HDPQ SP s Firmware The
More informationNEMA 4 Option Card Installation Manual
225880901 Installation Manual s! WARNING Serious or fatal electric shock may result from failure to remove electrical power from the SubDrive prior to installing the NEMA 4 Option Card. Disconnect power
More informationExamplify v12 Exam Instructions
Examplify v12 Exam Instructions 1) Downloading Exams (DO THIS PRIOR TO EXAM DAY) Watch for email notifications to download exams. Establish an Internet connection. Double-click the Examplify icon on the
More informationType 6150 AS-Interface Module. Type 3372 Electropneumatic Actuator with AS-interface module. Mounting and Operating Instructions EB 6150 EN
Type 6150 AS-Interface Module Type 3372 Electropneumatic Actuator with AS-interface module Mounting and Operating Instructions EB 6150 EN Edition July 2013 Definition of the signal words used in these
More information8000 Series: Installation Supplement R2-1-12
8000 Series: Installation Supplement R2-1-12 Smartscan Incorporated, 33083 Eight Mile Road, Livonia MI 48152 Tel: (248) 477-2900 Fax: (248) 477-7453 Web: www.smartscaninc.com SMARTSCAN INCORPORATED Livonia,
More informationEDK MHz EDK 350U 902 MHz EDK 400J 928 MHz. EnOcean Developer Kits USER MANUAL. Observe precautions! Electrostatic sensitive devices!
EDK 350 868 MHz EDK 350U 902 MHz EDK 400J 928 MHz EnOcean Developer Kits Observe precautions! Electrostatic sensitive devices! Patent protected: WO98/36395, DE 100 25 561, DE 101 50 128, WO 2004/051591,
More informationPITE 3926C Battery Data Logger User Manual
PITE 3926C Battery Data Logger User Manual P-140922-V1.3 4/F, Bldg A, Chiwan Industrial Park, Shaodi Rd., Chiwan, Shekou Area, Shenzhen, China TEL: +86-755-2680 5759 FAX: +86-755-2688 0310 www.pitetech.com
More informationUser Manual CIFX Cards Real Time Ethernet
User Manual CIFX Cards Real Time Ethernet Installation, Operation and Hardware Description Language: English www.hilscher.com Communication Interface Hilscher cifx-re Table of Contents 2 Table of Contents
More informationLED Commander 16/2 DMX controller. user manual
LED Commander 16/2 DMX controller user manual Musikhaus Thomann Thomann GmbH Hans-Thomann-Strasse 1 96138 Burgebrach Germany Telephone: +49 (0) 9546 9223-0 E-mail: info@thomann.de Internet: www.thomann.de
More informationTechnical Guide Plasma (GPH10DU Chassis) Troubleshooting Handbook
Technical Guide Plasma (GPH10DU Chassis) Troubleshooting Handbook Model : TH-42PX75U TH-50PX75U TH-42PX77U TH-50PX77U Panasonic Services Company National Training Prepared by Panasonic Service and Technology
More informationquick start manual FORERUNNER 50 with ANT+Sport wireless technology
quick start manual FORERUNNER 50 with ANT+Sport wireless technology Warning: This product contains a replaceable coin cell battery. See the Important Safety and Product Information guide in the product
More informationReadyNAS OS 6 Rack-Mount Hardware Manual
Rack-Mount Hardware Manual Model ReadyNAS 2120 ReadyNAS 2120 v2 ReadyNAS 3130 ReadyNAS 3138 ReadyNAS 3220 ReadyNAS 3312 ReadyNAS 4220 ReadyNAS 4312 ReadyNAS 4360 April 2017 202-11272-08 350 E. Plumeria
More information