Courtesy of:discountcarstereo.com USB-CDR30. ation Guide for Porsche CDR30/31. Radios Revised: January 10, 2018

Transcription

1 Courtesy of:discountcarstereo.com USB-CDR30 Quick Start Installation ation Guide for Porsche CDR30/31 Radios Revised: January 10, 2018

2 Introduction: Portable audio products are everywhere, reflecting demand from active people all over the world to take their music with them. Porsche offers an optional 3.5mm jack for the CDR30 and CDR31 Radio which may be satisfactory to some, but those looking for a better solution we offer the USB-CDR30. The USB-CDR30 replaces the optional 3.5mm jack and allows the user to play and charge all Apple lightning devices without sacrificing the look and feel of the dashboard components. Installation: Warning! Although not critical, we recommend disconnecting the car battery. 1. Remove CDR30/31 radio from dashboard to gain access to the connectors. (Radio removal not covered in these instructions) 2. With radio removed disconnect factory Quadlock plug (harness) from Radio (See Fig. 1 ) Fig. 1 Factory Quadlock 3. To remove radio plug, push up on tab (indicated by black arrow in Fig. 2) and pull outwards on lock release 4. Connect plug on adapter harness to Radio (See To Radio in Fig. 3) 3 5. Disconnect the 12-pin green and blue mini-quadlock plugs from factory plug (See Fig. 1) 1 Warning! CDR30/31 Radios with factory AUX and Bluetooth will have both a blue and green 12-pin mini-quadlock (Green for AUX and blue for Bluetooth). The AUX mini-quadlock remains disconnected and replaced with the black 12-pin mini-quadlock from Adapter. (See Fig. 2) 2 6. Reconnect 12-pin blue mini-quadlock plug (from step 5) to plug on adapter harness (To Radio in Fig. 3) 3

3 8. Decide where and how to mount USB terminal. A. Flush mount requires drilling a ¾ hole in the dash B. USB mounting bracket without drilling (use this option to mount the USB terminal wherever your installation demands) C. Un-mounted (Free standing USB terminal) Fig. 2 Quadlock Plug on Adapter harness A. Flush Mounting to Dash 1. Drill a ¾ hole in dash using a step drill bit or equivalent (See Fig. 4) 4 Green sub-plug remains disconnected (See Fig. 2) 2 7. Connect factory plug (from step 2) to mating connector on Adapter harness (To Car in Fig. 3) Fig. 4 Step drill bit Fig. 3 plug/connector on adapter harness 2. Insert the male end of the 3ft USB extension cable (See Fig. 5) 5 through the ¾ hole in dash and mate with USB Female terminal on adapter (See Fig. 6) 6 Ensure connections are snug Note to Vehicles with BOSE: You must transfer optical cable from factory plug to plug supplied with adapter.

4 Fig. 5 USB extension cable Fig. 8 Flush mounted USB terminal 4. Tuck and secure extra wire from moving parts and test operation (See Enabling the AUX section below) B. Mounting Bracket without drilling Fig. 6 USB Male (left) USB Female (Right) 1. Locate a flat surface at location of choice within 7 ft. of radio to mounting bracket to surface using adhesive/tape or screws. (See Fig. 9) 9 3. Push USB head ( See Fig. 7) 7 through hole until it snaps in place and flush with mounting surface (See Fig. 8) 8 Fig. 9 mounting bracket Fig. 7 Flat USB Terminal 2. Insert male end of 3ft USB extension cable through hole in bracket (See Fig. 10) and mate with Female USB terminal

5 from Adapter (See Fig. 11) 4. Tuck and secure extra wire away from moving parts and test operation (See Enabling the AUX section) C. Un-Mounted (Free Standing) USB Terminal Fig. 10 USB Male (left) USB Female (right) Simply route USB terminal (See Fig. 13) from behind the dash to location of choice within 4 ft. of radio and connect your Apple lightning cable. Fig. 13 Free standing USB Terminal Fig. 11 USB Male (left) USB Female (Right) 3. Push USB head through hole in mounting bracket until it snaps in place and flush (See Fig 12) Fig. 12 Test Operation 1. Connect Apple device to USB Terminal 2. Audio device will begin charging 3. On Radio, press CD/AUX button repeatedly until AUX Mode is enabled. Note: To switch from CD to AUX press the AUX Soft key. 4. Select a track from devices music library and it will play on the car speakers. Warning! Playlist and Track selection is *NOT* possible from the radio. You must use the ipod built-in controls to access music files.

6 5. Use the radio volume control to set playback level 6. If successful operation is confirmed go ahead and reinstall Radio Alert! Apple authentic Lighting cable is required for proper operation. Knock off Lightning cables will charge but may not play music. Compatibility The USB-CDR30 works on the following Apple Lighting devices. iphone Models ipad Models ipod Models iphone X iphone 8 iphone 8 Plus iphone 7 iphone 7 Plus iphone 6s iphone 6s Plus iphone 6 iphone 6 Plus iphone SE iphone 5s iphone 5c iphone 5 ipad Pro 10.5-inch ipad Pro 12.9-inch (2G) ipad Pro 12.9-inch (1G) ipad Pro 9.7-inch ipad ipad mini 4 ipad mini 3 ipad mini 2 ipad mini ipad Air 2 ipad Air ipod touch 6G ipod touch 5G ipod nano 7G Disclaimer This product has no affiliation with Porsche or Apple There are no warranties expressed or implied by purchase of this product Aux must be enabled, otherwise visit your Porsche dealer for assitance We re not liable for misuse of this product. We recommend professional installation. Call or support@discountcarstereo.com 1995-Jan-18 Discount Car Stereo, Inc. All rights reserved. Information in this document is subject to change without notice. Other products and companies referred to herein are trademarks or registered trademarks of their respective companies or mark holders.