PCW-2TB10 People Counter

Transcription

1 418MHz -Directional Wireless Sensor Rev. 5/14/

2 T A B L E O F CONTEN T S Table of Contents... 2 INTRODUCTION... 3 Product Overview... 3 Features... 3 Components... 3 Getting Started... 3 Caution... 3 HARDWARE OVERVIEW... 4 RX Unit Functions... 4 TX Unit Functions... 4 Sensor Specifications... 4 Batteries... 5 Hardware Diagram... 5 PREREQUISITES AND REQUIREMENTS... 6 Hardware... 6 Software... 6 Networking... 6 SETUP AND CONFIGURATION... 6 Software Installation... 6 RX Unit Configuration... 7 TX Unit Configuration... 7 INSTALLATION... 8 Front/Dual Mode... 8 Side Mode... 9 INTEGRATION... 9 LIMITED WARRANTY Rev. 5/14/

3 INTRODUCTION P R O D U CT O V E R V I E W The PCW-2TB10 is a battery operated infrared through beam people counter with a 418 MHz radio transmitter. The sensors are versatile and are ideal for entry ways up to twenty five feet wide. The system consists of three parts: the IR transmitter and the IR receiver and the SSRX 4.9 sensor server (sold separately). The sensors are directional; meaning they can count intraffic and out-traffic. Your data can be retrieved via the 6 digit LCD display or from the SSRX 4.9 sensor server. F E A T U R E S Radio operates at 418MHz frequency Maximum range of up to 500 Cover entrances of up to 25 Battery operated (replaceable) for a truly wireless installation 6-digit LCD screen Three Modes: side, front, or dual mode (directional) Low or high power of IR intensity Complies with part 15 of FCC rules C O M P O N E N T S Systems are custom built; these are components of a standard build. One transmitter TX unit and one receiver RX unit (batteries included) Two mounting plates Installation hardware One magnetic reset tool G E T T I N G ST A R T E D Read the instruction manual: An understanding of through beam technology and sensor placement is crucial for optimum accuracy. Configure sensors to appropriate mode (you must set the TX and RX to the same mode). Verify network connectivity to your sensor server Install mounting bracket Mount sensor C A U T I O N Light: Ambient light may cause false counts. Use the provided rubber diffusers to reduce ambient light. Impact/Shock: Heavy impact or shock may cause damage to hardware. Tampering: Changes or modifications not expressly approved by SenSource will void the warranty. Cleaning: Harsh cleaners, such as paint remover or benzene, may ruin the surface. Use a soft, wet cloth and mild soap or detergent to clean displays and lenses Rev. 5/14/2013 3

4 HARDWARE OVERVIEW RX U N I T FUNCT I O N S See figure 1. Reading the current counts: When the IR beam is broken the LCD display on the RX unit will list the current count value and the LED will flash red. The display may fall asleep to save energy; you may need to tap the configuration button to wake up the LCD display. To view the counts without breaking the beam briefly tap the configuration button on the RX unit. The LCD display will then show the current total counts, as well as which mode you are currently in Front, Side, or Dual. Or you can swipe the magnet across the sensor on the side opposite of the LCD display. Clearing the LCD Counter: The counter may be reset by using the magnetic reset tool and holding it on the side opposite of the LCD display for five seconds. Configuration Button: Is used to configure your sensor into the appropriate mode. See hardware configuration. 418MHz radio transmits data to your SenSource SSRX 4.9 sensor server. See SSRX 4.9 manual for more details on the sensor server. TX U N I T F U N C T I O N S See figure 2. The TX unit transmits an IR beam to be received by the RX unit. Configuration Button: Is used to configure your sensor into the appropriate mode. See hardware configuration. S E N S O R S P E C I F I CA T I O N S MIN TYP MAX IR Beam Range* Radio Transmit Range* Battery Life* 6 mo. 1 yr. 2 yr. * Ambient light may cause false counts. *Radio transmit range is determined by many factors. Max refers to line of sight with no obstructions. Walls, going around corners, metal, and other radio frequencies can affect the range of your device. *Battery life varies due to many factors including wireless network settings, use/traffic, and sensor configuration. SenSource recommends a regular maintenance program of new batteries every six months to ensure system optimization. Battery Type (Qty 4) 3.6v AA Lithium, 2x Each Enclosure -Indoor Use Only 3.5 x 1.75 x 1.0, ABS (CYCOLAC) Plastic Memory- Your sensor do not have memory; therefore it is very critical for your sensors to have charged batteries and a regular maintenance program is suggested. If your sensors batteries die, you will not receive data for the amount of time that the batteries were dead. Your sensor server has memory and holds your data. PCW-SSRX4.9 Sensor Server: Refer to PCW-SSRX4.9 sensor server manual or to SenSource knowledge base at 4 Rev. 5/14/

5 B A T T E R I E S In order to preserve battery life clear plastic pull tabs are installed. Before your sensors will be functional you must remove the pull tab. Figure 1. The sensors require four 3.6V Lithium AA batteries. To replace the batteries disconnect the sensor from the back-plate. Remove the battery compartment lid. Replace both batteries in the TX unit. NOTE The batteries go in the same directions ++. Replace both batteries in the RX unit. NOTE The batteries go in the same directions ++. Standard 1.5V Lithium AA batteries are NOT supported. Battery life: It is recommended to change your batteries every six months to ensure system optimization. H A R D W A R E DIAGRAM Figure 2. RX Unit Figure 3. TX Unit Rev. 5/14/2013 5

6 PREREQUISITES AND REQUIREMENTS H A R D W A R E Basic hand tools are required to mount the sensors on door frames or opposing walls. Mounting hardware included. S O F T W A R E Windows Operating System XP, Server 2003, Vista, Server 2008, 7 Processor - 32 bit 1.5 GHz Intel Pentium IV or AMD Athalon XP Processor - 64 bit 2.4 GHz Intel Core 2 Duo or AMD Turion Disk Space (stand-alone) 75 MB Disk Space (with Sequel 2008 Express R2) 2GB (4GB max) Memory - 32 bit 1GB Memory - 64 bit 2GB.Net 3.5 Service Pack 1 Net 4.0 Windows Powershell 1.0 Windows Installer 4.5 Windows Installer 4.5 update Java N E T W O R K I N G Your sensors are designed to work with a SenSource PCW-SSRX4.9 sensor server. Your sensor server can be configured via serial to PC, Ethernet to PC, or Ethernet to LAN/WAN. Refer to PCW-SSRX4.9 sensor server manual or to SenSource knowledge base at SETUP AND CONFIGURATION S O F T W A R E I N S T A L L A T I O N 1. Insert the installation CD into the disk drive bay. 2. Run index.htm or Open to view files. 3. Active Content: Internet Explorer may ask you if you would like to run active content. Choose Yes. 4. You can also launch the software by accessing your CD drive via My Computer. 5. On the software install home page choose 32 bit with or without SQL or choose 32 bit with or without SQL. 6. IE may ask you to confirm do you want to run or save SensorUtilitySetup. Choose Run or Save to the appropriate location. 7. Follow the installation wizard instructions to finish your install. 6 Rev. 5/14/

7 SENSOR CONFIGU RATION NOTE: Both your sensors the RX unit and the TX unit must be configured into the same mode in order to function properly. RX U N I T C O N F I G U R A T I O N See figure 2. To turn the unit on or select the mode of operation, use a paperclip to press and hold the configuration button. The LCD display will sequence through the available operation modes of set SIDE, set FRNT, set DUAL, SELFTEST, or PWR OFF. To select the desired mode, release the button when the display indicates the mode. To put the counter in alignment mode, momentarily press and release the configuration button on the RX unit. If the RX unit and TX unit are properly aligned, then the LED will be lit on the RX unit. You can exit alignment mode by pressing the configuration button again or allow it to time out on its own by waiting for sixty seconds. The RX unit has an internal magnetic switch located inside of the black enclosure on the side opposite of the LCD display. To display counts on the LCD display, swipe a magnet across the RX unit where the magnetic switch is located. To reset the counts to zero hold a magnet next the magnetic switch for approximately five seconds. TX U N I T C O N F I G U R A T I O N Figure 4. See figure 4. To select the mode of operation use a paper clip to press and hold the configuration button. The LEDs (located under the plastic enclosure) will flash red to provide feedback as to which mode you are currently in. Note: Low power mode is indicated by a solid red LED. High power mode is indicated by a flashing red LED Rev. 5/14/2013 7

8 INSTALLATION Understanding of side-firing, front-firing, and dual-firing is important before mounting your brackets. Your desired operating mode will determine the position of your mounting brackets. Proper orientation and alignment is required for counters to function properly. An orientation sticker (a red circle) has been placed on each unit to aid in identifying the correct orientation. (figure 5.) Verify the correct orientation of both sensors and brackets before using screws or fasteners to permanently mount the brackets and before removing the stickers. MOUNTING OVE RVIEW F R O N T/DU A L M O D E Figure 5. Front Firing Mode (Non-Directional): Is used when mounting the sensors on opposing walls. It is a non-directional mode, meaning that the sensors will not be able to distinguish between entries and exits. Mount both sensors so that the faces are pointing at each other and that the orientation stickers are facing down toward the floor. Dual Mode (Directional): Is used when mounting the sensors on opposing walls and distinguishes between enter and exit counts. Mount both sensors so that the faces are pointing at each other and that the orientation stickers are facing down toward the floor. 8 Rev. 5/14/

9 S I D E MODE Side-firing mode is used when mounting the sensors on a door frame. It is a non-directional mode, meaning that the sensors will not be able to distinguish between entries and exits. If the RX unit (unit w/ LCD display) is mounted on the right side of the entrance, both orientation stickers should be facing the left. If the RX unit (unit w/ LCD display) is mounted on the left side of the entrance, borth orientation stickers should point to the right. NOTE: When using side firing mode, the orientation stickers should be removed after the sensors have been mounted and tested, as they may disrupt the beam. 1. After installing the sensor utility software INTEGRATION 2. Send a service signal from the RX unit by tapping the service button on the RX (located to the right of the USB port) until the LED indication flashes briefly 3. The sensor will show up in the unassigned category in your Server Manager software 4. For more information on System Manager, Vea, or reports please visit our Knowledge Base at SenSource.com Server Manager software is used in conjunction with sensor servers. Server manager allows you to define regions, districts, and facilities by breaking down your organization into a tree. Server manager is stand-alone, no SQL required to connect your applications. You can generate reports right from the server manager software. Vea View is a robust tool that allows you to see business metrics that combine multiple data sources such as point of sale and customer traffic. Reporting can be automated and sent to your recipient group Rev. 5/14/2013 9

10 LIMITED WARRANTY HARDWARE: SenSource, Inc. warrants to the original end user ("Customer") that this product will be free from defects in workmanship and materials (under normal use) for one year from date of shipment from SenSource, Inc. or its authorized reseller. SenSource, Inc.'s sole obligation under this express warranty shall be (at SenSource, Inc.'s option and expense) to replace the product or part with a comparable product or part, repair the product or part, or if neither repair nor replacement is reasonably available SenSource, Inc. may (in its sole discretion) refund to Customer the purchase price paid for the product or part. Replacement products or parts may be new or reconditioned. SenSource, Inc. warrants any replaced or repaired product or part, and any hardware upgrade to which Customer is entitled under an agreement between Customer and SenSource, Inc. for the remainder of the original warranty period. All products or parts, returned for replacement, become the property of SenSource, Inc. SOFTWARE: SenSource, Inc. warrants to Customer that provided software will perform in substantial conformance to their program specifications for a period of ninety days from the date of original purchase from SenSource, Inc. or its authorized reseller. SenSource, Inc. warrants the media-containing software against failure during the warranty period. No updates are provided. SenSource, Inc. does not provide any warranty for any third-party software that is licensed to Customer by the third party. SenSource, Inc.'s sole obligation, with respect to this express warranty, shall be (at SenSource, Inc.'s discretion) to refund the purchase price paid by Customer for any defective software product, or to replace any defective media with software, which substantially conforms to applicable specifications. SenSource, Inc. makes no warranty or representation that its software products will meet Customer's requirements, will work in combination with any hardware or software products provided by third parties, that the operation of the software products will be uninterrupted or error free, or that all defects in the software products will be corrected. OBTAINING WARRANTY SERVICE: Customer must contact SenSource, Inc. Technical Support (PH: option 3 or support@sensource.biz) within the applicable warranty period to obtain warranty service. Dated proof of original purchase from SenSource, Inc. or its authorized reseller is required. SenSource, Inc. is not responsible for Customer products or parts received without a warranty service authorization (or Return Materials Authorization, RMA ). In the United States, SenSource, Inc. may ship a replacement product or part prior to receiving the original product or part ("advance exchange"). If advance exchange is not available, then the repaired product or part will be shipped as soon as reasonably possible. Repaired or replacement products will be shipped to the Customer at SenSource, Inc.'s expense. The repair and replacement process for products or parts in locations outside of the United States will vary depending on Customer's location. All materials are to be shipped to the following address only after Customer obtains a Return Materials Authorization (RMA): SenSource, Inc., Attn: Returns Department, 3890 Oakwood Ave, Youngstown, OH Products or parts shipped by Customer to SenSource, Inc. must be sent prepaid and packaged appropriately for safe shipment. SenSource, Inc. recommends insuring the package, or shipping by a method that provides for tracking of the package. When an advance exchange is provided, SenSource will charge customer for the replacement items and issue credit when the faulty items are received and evaluated. WARRANTIES EXCLUSIVE: IF A PRODUCT DOES NOT OPERATE AS WARRANTED ABOVE, CUSTOMER'S SOLE REMEDY FOR BREACH OF THAT WARRANTY SHALL BE REPLACEMENT OR REPAIR OF THE PRODUCT OR PART, OR REFUND OF THE PURCHASE PRICE PAID (AT SENSOURCE, INC.'S OPTION). TO THE FULL EXTENT ALLOWED BY LAW, THE FOREGOING WARRANTIES AND REMEDIES ARE EXCLUSIVE, AND ARE IN LIEU OF ALL OTHER WARRANTIES, TERMS, OR CONDITIONS. EXPRESS OR IMPLIED, EITHER IN FACT OR BY OPERATION OF LAW, STATUTORY, OR OTHERWISE, INCLUDING WARRANTIES, TERMS, OR CONDITIONS OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, SATISFACTORY QUALITY, CORRESPONDENCE WITH DESCRIPTION, AND NON- INFRINGEMENT ALL OF WHICH ARE EXPRESSLY DISCLAIMED. SENSOURCE, INC. NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO ASSUME FOR IT ANY OTHER LIABILITY IN CONNECTION WITH THE SALE, INSTALLATION, MAINTENANCE, OR USE OF ITS PRODUCTS. SENSOURCE, INC. SHALL NOT BE LIABLE UNDER THIS WARRANTY IF ITS TESTING AND EXAMINATION DISCLOSE THAT THE ALLEGED DEFECT OR MALFUNCTION IN THE PRODUCT DOES NOT EXIST OR WAS CAUSED BY CUSTOMER'S, OR ANY THIRD PERSON'S, MISUSE, NEGLECT, IMPROPER INSTALLATION OR TESTING, UNAUTHORIZED ATTEMPTS TO OPEN, REPAIR, OR MODIFY THE PRODUCT, OR ANY OTHER CAUSE BEYOND THE RANGE OF THE INTENDED USE, OR BY ACCIDENT, FIRE, LIGHTNING, POWER CUTS OR OUTAGES, OTHER HAZARDS, OR ACTS OF GOD. THIS WARRANTY DOES NOT COVER PHYSICAL DAMAGE TO THE SURFACE OF THE PRODUCT, INCLUDING CRACKS OR SCRATCHES ON THE LCD DISPLAY OR OUTSIDE CASING. THIS WARRANTY DOES NOT APPLY WHEN THE MALFUNCTION RESULTS FROM THE USE OF THIS PRODUCT IN CONJUNCTION WITH ACCESSORIES, OTHER PRODUCTS, OR ANCILLARY OR PERIPHERAL EQUIPMENT, AND SENSOURCE, INC. DETERMINES THAT THERE IS NO FAULT WITH THE PRODUCT ITSELF. THIS WARRANTY DOES NOT APPLY TO ANY MALFUNCTION OR FAILURE OF THE PRODUCT OR PART DUE TO ANY COMMUNICATION SERVICE CUSTOMER MAY SUBSCRIBE TO FOR USE WITH THE PRODUCT. LIMITATION OF LIABILITY: TO THE FULL EXTENT ALLOWED BY LAW, SENSOURCE, INC. ALSO EXCLUDES (FOR ITSELF AND ITS SUPPLIERS) ANY LIABILITY, WHETHER BASED IN CONTRACT OR TORT (INCLUDING NEGLIGENCE), FOR INCIDENTAL, CONSEQUENTIAL, INDIRECT, SPECIAL, OR PUNITIVE DAMAGES OF ANY KIND, OR FOR LOSS OF REVENUE OR PROFITS, LOSS OF BUSINESS, LOSS OF INFORMATION OR DATA, OR OTHER FINANCIAL LOSS ARISING OUT OF OR IN CONNECTION WITH THE SALE, INSTALLATION, MAINTENANCE, USE, PERFORMANCE, FAILURE, OR INTERRUPTION OF THIS PRODUCT, EVEN IF SENSOURCE, INC. OR ITS AUTHORIZED RESELLER HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES, AND LIMITS ITS LIABILITY TO REPLACEMENT, REPAIR, OR REFUND OF THE PURCHASE PRICE PAID AT SENSOURCE, INC. S OPTION. THIS DISCLAIMER OF LIABILITY FOR DAMAGES WILL NOT BE AFFECTED IF ANY REMEDY PROVIDED HEREIN SHALL FAIL OF ITS ESSENTIAL PURPOSE. DISCLAIMER: Some countries, states, or provinces do not allow the exclusion or limitation of implied warranties, or the limitation of incidental or consequential damages for certain products supplied to consumers, or the limitation of liability for personal injury. Therefore, the above limitations and exclusions may be limited in their application to Customer. When the implied warranties are not allowed to be excluded in their entirety, they will be limited to the duration of the applicable written warranty. This warranty gives Customer specific legal rights, which may vary depending on local law. GOVERNING LAW: This Limited Warranty shall be governed by the laws of the State of Ohio, U.S.A., and by the laws of the United States, excluding their conflicts of laws principles. The United Nations Convention on Contracts for the International Sale of Goods is hereby excluded in its entirety from application to this Limited Warranty. RESTOCKING POLICY: Items in good condition may be returned within 30 days of shipment at no charge to the Customer (not including shipping charges). A pre-approved Returned Materials Authorization (RMA) must accompany returned merchandise. Items returned will be inspected for damage and Customer will be notified of credit approval. Restocking fees will apply to items returned beyond 30 days and may vary with each product. FRM-1050 / Rev. 5/14/