1 Preparations. English for U.S.A. AV Receiver. Accessories. Cables necessary for connections

Transcription

1 1 Preparations Accessories AV eceiver Check that the following accessories are supplied with this product. emote control Batteries (AAA, 03, UM-4) (x 2) Easy Setup Guide English for U.S.A. YPAO microphone Insert into the remote control in the correct polarity (+/-). VIDEO AUX input cover AM antenna FM antenna CD-OM Safety Brochure Easy Setup Guide (Owner s Manual) (this document) Cables necessary for connections. You need to separately prepare the following cables to build the system based on this document. Speaker cables (depending on the number of speakers) cable (x 2) Audio pin cable (x 1) Digital optical cable (x 1) (unnecessary if your TV supports AC)

2 2 Placing the speakers Set up the speakers in the room by using the following diagram as a reference. For information on other speaker systems, refer to Owner s Manual..1-channel system 7.1-channel system cm (1 ft) or more Front speaker () Front speaker () Center speaker Surround speaker () Surround speaker () Surround back speaker () Surround back speaker () Subwoofer 2 En

3 3 Connecting the speakers/subwoofer This unit is configured for 8-ohm speakers at the factory. When connecting 6-ohm speakers, set the speaker impedance of this unit to 6 Ω MIN. For details, see Setting the speaker impedance (p.16) in Owner s Manual. Use a subwoofer equipped with built-in amplifier. emove the power cable of this unit from an AC wall outlet and turn off the subwoofer before connecting the speakers. Be careful that the core of the speaker cable does not touch anything or come into contact with the metal areas of this unit. This may damage this unit or the speakers. If the speaker cables short circuit, CHECK SP WIES will appear on the front display when this unit is turned on. Connecting speaker cables Speaker cables have two wires. One is for connecting the negative (-) terminal of the unit and the speaker, and the other is for the positive (+) terminal. If the wires are colored to prevent confusion, connect the black wire to the negative and the other wire to the positive. emove approximately 10 mm of insulation from + (red) the ends of the speaker cable, and twist the bare wires of the cable together firmly. (black) oosen the speaker terminal. Insert the bare wires of the cable into the gap on the side (upper right or bottom left) of the terminal. Tighten the terminal. FONT 1 Connect the front speakers ( / ) to the FONT ( / ) terminals. SPEAKES FONT CENTE SUOUND SUOUND BACK/BI AMP SUBWOOFE SINGE EXTA SP PESENCE 2 Connect the center speaker ( ) to the CENTE terminal. SPEAKES FONT CENTE SUOUND SUOUND BACK/BI AMP SUBWOOFE SINGE EXTA SP PESENCE Using a banana plug Tighten the speaker terminal. Insert a banana plug into the end of the terminal. Banana plug FONT En 3

4 the surround speakers ( 3 Connect ) to the SUOUND ( / ) / the subwoofer ( 4 Connect SUBWOOFE jack. ) to the Connect the surround back speakers ( ) to the SUOUND BACK ( / ) terminals. terminals. FONT CENTE SUOUND SUOUND BACK/BI AMP FONT CENTE SUOUND SPEAKES SUOUND BACK/BI AMP SINGE CENTE SUOUND SUOUND BACK/BI AMP EXTA SP PESENCE SUBWOOFE SUBWOOFE Use an audio pin cable to connect the subwoofer ( ). En SINGE EXTA SP PESENCE 4 FONT SINGE / SPEAKES SPEAKES For 7.1-channel system Audio pin cable EXTA SP PESENCE SUBWOOFE

5 P PB MAIN ZONE PHONES SIENT CINEMA OPTICA AV 1 COAXIA AV 2 YPAO MIC USB ipod/iphone COAXIA OPTICA (TV) AV 4 AV AV 6 AM AC FM 7Ω AUDIO 1 ZONE2 ZONE CONTO INFO MEMOY PESET CATEGOY FM AM INPUT P PB AUDIO 2 VIDEO MONITO OUT IN OUT TIGGE OUT BD DVD EMOTE TONE CONTO FONT CENTE SUOUND SUOUND BACK/BI AMP SCENE AUDIO OUT TV CD ADIO POGAM ZONE 2 OUT STAIGHT TUNING/CH VIDEO AUX SUBWOOFE IN VIDEO AUDIO SINGE EXTA SP PESENCE PUE DIECT VOUME 4 Connecting the external devices Audio out (optical) OPTICA O TV in out BD/DVD player 1 Connect the external devices to this unit. Connect the BD/DVD player and this unit with an cable. If the BD/DVD player is currently connected to the TV directly with an cable, disconnect the cable from the TV and connect it to this unit. Connect the TV and this unit with another cable. Connect the TV and this unit with a digital optical cable. This connection is required to play back TV audio on this unit. If your TV supports AC (Audio eturn Channel), this connection is unnecessary. Connect the power cable to an AC wall outlet. OUT 1 (BD/DVD) AV4 (OPTICA) jack O OUT jack SIIUS DOCK Y COMPONENT VIDEO OPTICA (TV) AV 4 VIDEO AV 3 (CD) NETWOK AC OUT ANTENNA AV OUT COMPONENT VIDEO Y 1 (BD/DVD) +12V 0.1A MAX. 1 jack SPEAKES To an AC wall outlet 2 3 For information on how to connect radio antennas or other external devices, see SETUP in Owner s Manual. Turn on this unit, TV and BD/DVD player. With the remote control of the TV, switch the TV input to display the video from this unit. The connections are complete. Move to the next page to optimize the speaker settings. NATUA SOUND AV ECEIVE X-V671 Turn on this unit This unit (front) En

6 Optimizing the speaker settings automatically (YPAO) By using the Yamaha Parametric room Acoustic Optimizer (YPAO) function, this unit automatically detects speaker connections and distances from the listening position, and optimizes the speaker settings such as volume balance and acoustic parameters to suit your room. 1 Connect the YPAO microphone to the YPAO MIC jack on the front panel. The following screen appears on the TV. During the measuring process, the test tones are output at high volume. Take care that the test tone does not frighten small children. Also, refrain from using this function at night when it may be a nuisance to others. MAIN ZONE 2 SOUCE ECEIVE CODE SET During the measuring process, you cannot adjust the volume. During the measuring process, keep the room as quiet as possible. Do not connect headphones. If your subwoofer supports the auto-standby function, disable it. YPAO measurement is not performed correctly when any obstacles are in the room. During the measuring process (about 3 minutes), keep stuff in the corners or remove it from the room. Preparing for YPAO Turned on the subwoofer and set the volume to half. If the cross-over frequency is adjustable, set it to maximum. VOUME COSSOVE/ HIGH CUT This unit (front) V-AUX AV 6 AUDIO DOCK TUNE SIIUS NET USB CATEGOY FM AM PESET TUN./CH INFO MEMOY SU. DECODE STAIGHT MOVIE MUSIC SEEP ENHANCE PUE DIECT SCENE BD TV CD ADIO DVD ON SCEEN OPTION ENTE VOUME ETUN DISPAY Cursor keys ENTE ETUN To cancel the operation, disconnect the YPAO microphone before starting the measurement. 2 To start the measurement, use the cursor keys to select Measure and press ENTE. The measurement will start in 10 seconds. The following screen appears on the TV when the measurement finishes. TOP MENU POP-UP MENU MUTE MODE HOD MIN MAX MIN MAX YPAO microphone istening position ENT INPUT MUTE TV TV VO TV CH Ear height Place the YPAO microphone at ear height in your listening position. We recommend using a tripod to adjust the height. You can use the tripod screws to fix the microphone in place. If any error message (such as E-1) or warning message (such as W-2) appears, see Error messages (p.36) or Warning messages (p.37) in Owner s Manual. If the warning message W-1:Out of Phase appears, see If W-1:Out of Phase appears (next page). 6 En

7 3 Use the cursor keys to select Save/Cancel and press ENTE. If W-1: Out of Phase appears Follow the procedure below to check the speaker connections. Depending on the type of speakers or room environment, this message may appear even if the speakers are connected correctly. 4 Use the cursor keys to select SAVE and press ENTE. Use the cursor keys to select esult and press ENTE. Use the cursor keys to select Wiring. Check the cable connections (+/-) of the speaker indicated with everse. Disconnect the YPAO microphone from this unit. Now optimization of the speaker settings is complete. If the speaker is connected correctly: You can save the current settings. Press ETUN and proceed to step 3. If the speaker is connected incorrectly: Turn off this unit, reconnect the speaker cable, and then try YPAO measurement again. Since the YPAO microphone is sensitive to heat, do not place the microphone in any place where it will be subjected to direct sunlight or high temperatures (top of an AV equipment, etc). En 7

8 6 Playing back a BD/DVD Now let s play back a BD/DVD. We recommend playing back multichannel audio (.1- channel or more) to feel surround sound produced by this unit. MAIN ZONE 2 SEEP INFO MOVIE BD DVD ON SCEEN MODE MEMOY MUSIC 6 SOUCE AV PESET SU. DECODE ENHANCE V-AUX STAIGHT PUE DIECT ADIO VOUME MUTE INPUT MUTE TV VO TV ECEIVE AUDIO POP-UP MENU 7 8 TV CH CODE SET 6 DOCK SIIUS TUNE NET USB FM HOD CATEGOY AM TUN./CH ENT 1 STAIGHT VOUME Press 1 to select 1 as the input source. 1 Start playback on the BD/DVD player. Press STAIGHT repeatedly to select STAIGHT. STAIGHT When STAIGHT (straight decode) is enabled, each speaker produces each channel audio signal directly (without sound field processing). If you play back.1-channel audio on the 7.1-channel system, no sounds will be heard from the surround back speakers. Press VOUME to adjust the volume. Volume -30.0dB Now the basic setup procedure is complete. If you cannot have surround sound Only the front speakers work on multichannel audio Check the digital audio output setting on the BD/DVD player. It may be set to output 2-channel audio (PCM, etc.) only. No sound is heard from a specific speaker See Troubleshooting (p.109) in Owner s Manual. VO. VO. VO. S S S SW C SW C SW C S S S Much more features! This unit has various other functions. Please refer to Owner s Manual on the supplied CD-OM and utilize this unit effectively. Connecting other playback devices (p.26) Connect audio devices (CD player, etc.), game console, camcorder, and many others. Selecting the sound mode (p.40) Select the desired sound program (CINEMA DSP) or surround decoder suitable for movies, music, games, sports programs and other uses. Playing back from ipod (p.4) By using a USB cable supplied with ipod, an optional Yamaha ipod dock or an optional Yamaha ipod wireless system, you can enjoy ipod music on this unit. istening to FM/AM radio (p.4) Playing back music stored on a USB storage device (p.61) Playing back the network contents (p.64 to p.67) Selecting the input source and favorite settings at once (p.39) For more information, see What you can do with this unit (p.6) Yamaha Corporation YD48A0/ESEN1