Digital Snitch Wireless Camera Interceptor Pro. Model: PEB900. User Guide

Transcription

1 Digital Snitch Wireless Camera Interceptor Pro Model: PEB900 User Guide

2 Introduction Thank you for purchasing the Digital Snitch Wireless Camera Interceptor Pro. Please first read over this manual for proper use, save it and keep it handy. The Digital Snitch Wireless Camera Interceptor pro uses Radio Frequency (RF) scanning technology to detect hidden cameras, audio/video bugs, and intercept into those devices up to 300 feet (varies depending on the output of transmission source). It can be used to detect and locate hidden bugs in your home, office or other areas of concern. The Digital Snitch Wireless Camera Interceptor Pro constantly scans the area for any signal strength of a potential threat. When detecting the signal of the potential threat, the device will then display the hidden camera on the monitor Display LCD Screen and/or project the audio on the speaker.

3 HOW TO OPERATE 1. The Digital Snitch Wireless Camera Interceptor Pro might need a short time to warm up when exposed to cold weather. If the screen displays vertical lines when turned ON, please wait several seconds for the device to warm up. 2. Turn on the power switch and the device will start auto scanning. Below the Display LCD Screen you will notice

4 three rows of red LED lights, which indicate the band of frequency being scanned. When this device detects a wireless camera signal, the correspo nd ending " Band indication" (yellow LED) will light up and the screen will show the image 3. There are 3 sets of "Image lock and indication" on the right side of the screen. Below the screen you will notice 3 rows of red LED lights, which indicate the band frequency being scanned. 4. Press the "Scan / Stop" button of the correspondent band once to select the image and the red Lock LED will light up. The scanning indication (red LED row) of the locked band will stop moving, but the scanning indication (red LED row) of other unlocked bands will continue to move indicating that those bands are still being scanned. The Band indication (yellow LED) will stay at the locked band and the screen will show the image of lock band. 5. The Video system indication (green LED) will light up at NTSC or PAL /SECAM to indicate the detected signal is NTSC or PAL /SECAM. *NTSC is standard for US users and PAL is for European users. 6. If the wireless c camera is sending

5 audio signals, the speaker will play the sound that the microphone hears. 7. Press "Fine tune" buttons (+ -) to adjust the screen image. To change the frequency band that will display on the screen, press the Band Selection button. If the device detects wireless camera signals in the band you selected, the screen will display the image. 8. Press the Scan / Stop (start/stop) button of the correspondent band once to select the second detected image and the red Lock LED will light up. 9. The scanning indication (red LED) of the second locked band will stop Moving, the scanning indication (red LED) of other unlocked bands will continue to move. Note: This device can lock the image of the 3 frequency bands at the same time. 10. Press band selection switch to shift and watch the screen image of dif ferent frequency bands POWER SAVING MODE To use the power saving mode, press and hold the Band Selection button and turn the device ON. The LCD screen will first light up in blue then turn off. When it detects video signals, the Display LCD Screen will light up and display the video image.

6 AUDIO/VIDEO OUTPUT There are 3 AV output jack in the right side. Connect the A / V output cables with DVR to record the scanned audio and video signal of the 3 frequency bands individually. The external optional recorder should have audio input to enable the audio recording. And only the displayed frequency band could record the audio. Above the AV output jacks, there are 3 Video output tuners for adjusting the output video image of the 3 frequency b a nd s in o r d er to match the connected recording device (Optional: DVR). DISPLAY LCD SCREEN CONTOL BUTTONS There are 4 buttons on the left side of front view: Power - Menu - Down - Up 1. Press POWER to switch OFF / On the Display LCD screen. 2. Press MENU Key get into OSD (On- Screen Display) control: Contrast, Brightness, Hue (Color), Saturation (Tint, NTSC only), Sharpness, Volume. 3. Press UP and DOWN" to increase or decrease the setting.

7 AUDIO DETECTION This device has audio Detection covering the most popular frequencies The available audio Detection frequencies are as follows: No. Wireless Camera Audio Frequencies Frequency Band 6.0 MHz 6.5 MHz 5.5 MHz GHz V (default) V V GHz V (default) V V GHz V V (default) N/A When this device detects wireless camera signals, hold the Band selection button and press the Scan/Stop button of selected band (1.2 GHz or 2.4 GHz or 5.8 GHz) once to shift t the frequency of audio Detection. For example, the default audio Detection of 1.2 GHz band is 6.0 MHz, af ter completing step ( 2) above, it will shift t to 6.5 MHz If you want to repeat the step ( 2) once more, the audio Detection will shift t to 5.5 MHz Then back to 6.0 MHz 6.5 MHz 5.5 MHz if step (2) is further repeated. NOTE: The audio Detection of 5.8 GHz band has 2 frequencies only: 6.5 MHz and 6.0 MHz. Once the device is turned OFF, the audio Detection will return to the default frequency.

8 LOW BATTERY WARNING When the batter y low indication light is on, it means the batter y is running down. Please connect the switching power adaptor to recharge the batter y. While charging, you can continue using the device. It will take about 36 hours to fully charge the batter y if this device is working (power ON). It takes only 8 hours to fully charge the batter y if this device is powered OFF. If you are not going to use this device for a long time, please check the batter y power ever y 2-3 months. If the batter y runs down, connect the AC adaptor to recharge the built-in rechargeable battery for eight (8) hours. This will ensure longevity of the battery and also prevent damage to unit due to battery deterioration. NOTICE OF BATTERY 1. When the battery runs down, if the switch still keeps at "on", the battery will be over discharged and will damage the battery. Please set the on/off Switch at "off" and connect the power adaptor to charge this unit for 8 hours. 2. Battery will be over charged if you keep on charging it without using that will also damage battery. The producer and seller accept no liability for the damage caused by the over discharge or charge.

9 Operation Time Model, Voltage (V), Capacity (AH), Screen On, Power saving Inside Battery Approximately 40 minutes Approximately 70 minutes Notice of Use Avoid charging the device for more than 8 consecutive hours as this may result in damage to the battery due to overcharging. The manufacturer accepts no liability for the damage caused by over-charging or discharging. 1. Unauthorized repair or dismantle of this device will void all warranties. 2. Always use manufacturer s original power adaptor to avoid damage to the circuitry. 3. Avoid exposure to water. 4. Do not store this device in an excessively hot place. 5. Avoid knocking or dropping this device. 6. Never use the antenna of this device to touch a metal surface or the antenna of another electronic device. The quality warranty does not include the damage caused by static electricity or feedback. SPECIFICATION Power Battery life Detecting frequencies Dimension Weight Built-in rechargeable battery Normal mode: about 40 minutes after full charge Power saving mode: about 70 minutes after full charge 1.2GHz, 2.4GHz, 5.8GHz three frequency bands L 19 x H 14 x T 4 cm (antenna length not included) 860 g

10 Warning mode 1 Acoustic display Warning mode 2 Silent detection through earphone Detecting Distance: Up to 300 feet (varies on output power of transmitting source) Audio Detection 1.2 GHz band 6.0 MHz 6.5 MHz 5.5 MHz 2.4 GHz band 6.0 MHz 6.5 MHz 5.5 MHz 5.8 GHz band 6.0 MHz 6.5 MHz Audio/Video Output AV outputs x 3 for 3 bands synchronous recording, with 3.5mm Video/Audio output jack x 3 (for recording) * Specifications may change without notice. The detecting distance will be varied depending on the type and output power of signal sources. Limited Warranty The Manufacturer will repair or replace this product with new or refurbished parts from the date of the original purchase in the event of a defect in materials or workmanship, as follows: Materials and Labor: Ninety (90) days from the date of the original purchase. This warranty is extended only to the original purchaser. A purchase receipt or other proof of date of purchase and original purchase receipt will be required before warranty service is rendered. This warranty only covers failures due to defects in materials or workmanship, which occur during normal use as described in this Operator's Manual. The warranty does not cover damage which occurs in shipment or failures which are caused by products that are not supplied by the warrantor or failures which result from accident, misuse, abuse, neglect, mishandling, alteration, maladjustment of consumer controls, modification, rental use of the product, or service by anyone other than a manufacture service person. Opening the sealed portions of the Digital Snitch Wireless Camera Interceptor pro will result in voiding of this warranty.

11 Limited Warranty The Manufacturer, its Reseller(s), and Digital Snitch assume no liability associated with the use or misuse of the Digital Snitch Wireless Camera Interceptor Pro. Under no circumstances is the Manufacturer, its Reseller(s), Digital Snitch, its officers, agents, employees, or parent companies, liable for any loss, damage, or expenses of any kind arising out of the use, or inability to use, these products, or the suitability of use for any particular task. It is important to follow the procedure; outlined in this manual to ensure safe use of the Digital Snitch Wireless Camera Interceptor Pro. Limits and Exclusions There are no express warranties except as listed above. The warrantor shall not be liable for incidental or consequential damages resulting from the use of this product, or arising out of any breach of this warranty. All express and implied warranties, including warranties of merchantability and fitness for a particular purpose, are limited to the applicable warranty period set forth above. The effectiveness of the Digital Snitch Wireless Camera Interceptor pro device depends on the skill of the operator and camera configuration, thus it cannot be guaranteed to locate all hidden cameras, audio devices, etc. It is highly recommended that the user spend time practicing with the Digital Snitch Wireless Camera Interceptor pro to locate known cameras.