Technical Manual EDGE E65 Mini-BTE

Size: px
Start display at page:

Download "Technical Manual EDGE E65 Mini-BTE"

Transcription

1 Technical Manual EDGE E65 Mini-BTE Global Technical Operations gto.gnresound.com Lautrupbjerg 7 DK-2750 Ballerup Denmark Phone: Service@Beltone.com

2 Table of contents Description... Typical performance data IEC 8-7/ANSI Part list Diagram...4 Programming cable...5 How to separate the instrument...6 Amplifi er assembly Microphone complete...9 Receiver complete...20 Frame assembly...2 Coating instructions - amplifi er...22 How to place fi lters - front and back...2 Instrument complete in housing...24 Service tool...25 Accessories...26 Measurement tool and dome...27 How to place/remove the colour marker...28 Test equipment...29 Placing and adjusting test fixture...0 Testing... Page 2 of

3 Description Key features: Features an entirely new case design. Uses Coyote 2 DSP amplifi er - same proven technology as in the Beltone Oria family. It is targeted at end-users with mild to moderate and ski-slope hearing losses. Fully programmable digital hearing instrument. Programming connection: CS 6 mini-din programming cable, using -terminal fl ex strip to connect to the instrument. One microphone directional sound processing. -band WDRC compression system using Warplll Active feedback suppression. Unique open canal fitting design featuring a selection of domes and tubes allowing for quick in-offi ce fi tting. Options: Programmed with minimum the Solus fitting software ver.. or higher using the HI-PRO programming inter faces. Accessories: Clothing clip for programming cable. 5-pack disposable sound tubes for each configuration. Dispenser tool box.. Adapter for 2cc coupler. Typical battery life size 0: 70 hours Page of

4 Typical performance data - IEC 8-7 2cc coupler (Normal power) Data in accordance with IEC Supply Voltage. V. Unless otherwise is stated, all measurements made without Directionally, Noise Reduction, Spectral Enhancement or DFS active. Max. output (90 db SPL input) Max. output (90 db SPL input) at 2500 Hz Tolerance +/- 4 +/- 4 Unit db SPL db SPL Full-on gain (input 50 db SPL) Full.on gain (input 50 db SPL) at 2500 Hz 8 4 +/- 5 +/- 5 db db Total Harmonic Distortion Equivalent Input Noise w/o Noise reduction Reference test gain 600 Hz (60 db SPL input) Current Drain at 500 Hz at 800 Hz at 600 Hz * * Max. 5.0 Max max.. % db SPL db ma * The device is a high frequency hearing aid with a lower cut off frequency at 000 Hz Full-on gain Parameter Settings G(80) G(50) Page 4 of

5 Typical performance data - ANSI 2cc coupler Data in accordance with ANSI S Supply Voltage.V. Unless otherwise is stated, all measurements made without Directionality, Noise Reduction, Spectral Enhancement or DFS active. Full-on gain (90 db SPL input) HFA Full.on gain Tolerance +/- 4 +/- 4 Unit db SPL db SPL Full-on gain (input 50 db SPL) HFA Full.on gain 8 +/- 5 +/- 5 db db Reference test gain HFA 9 +/- 6 db Total Harmonic distortion Equivalent input noise Current Drain at 500 Hz at 800 Hz at 600 Hz * * Max. 5.0 Max. 5 Max.. % db SPL ma * The device is a high frequency hearing aid with a lower cut off frequency at 000 Hz G(80) G(50) Page 5 of

6 Typical performance data 2cc coupler 20 0 Max. output (OSPL90) Full-on gain Input 50dB SPL Full-on gain 50 db SPL input Reference test gain 60 db SPL input Page 6 of

7 Part list Item Part No. Item Part No. Receiver complete Reveiver 26D0/ Suspension Wire, ESW 7x2μ, red 8 mm Wire, ESW 7x2μ, green 20 mm Wire, ESW 7x2μ, red 6 mm Wire, ESW 7x2μ, green 6 mm Coating, EGC-700, 00 ml Microphone complete Microphone 960 Suspension, front Suspension, back Wire, ESW 7x2μ, red 2 mm Wire, ESW 7x2μ, amber 2 mm Wire, ESW 7x2μ, green 2 mm Wire, ESW 7x2μ, green 9 mm Wire, ESW 7x2μ, blue 9 mm Hybrid, Coyote 2.0 fl ex Molykote FS 292 Sound outlet / stud Pin lock Rubber glue, Casco Contact Module Battery Pill Spring battery, negative Spring battery, positive Wire, ESW 7x2μ, green mm Wire, ESW 7x2μ, red 8 mm Colour marker, red 25 pcs Colour marker, blue 25 pcs Programming cable CS6 ( pin) Flex strip for CS6 ( pin) pcs Prog. cable CS44 (4 pin) blue-left Prog. cable CS44 (4 pin) red-right Flex adapter CS6 (incl. a pin flex-strip Cleaning brush Clothing dip 25pcs Test fi xture Snap-in adaptor (for DSA5000 couplers) Measuring sound tube, Bend (for TBS25 / ATC 4000 test chamber) Service Tool Pin removal tool Page 7 of

8 Part list - housings, all colours Item Part No. Item Part No. White : Housing, printed Frame with serial number Battery door, printed Filters front, 4pcs Filters back, 4 pcs Filter box complete mic, front Filter box complete mic, back Black : Housing, printed Frame with serial number Battery door, printed Filters front, 4pcs Filters back, 4 pcs Filter box complete mic, front Filter box complete mic, back Medium blonde : Housing, printed Frame with serial number Battery door, printed Filters front, 4pcs Filters back, 4 pcs Filter box complete mic, front Filter box complete mic, back Metallic: Housing, printed Frame with serial number Battery door, printed Filters front, 4pcs Filters back, 4 pcs Filter box complete mic, front Filter box complete mic, back Marble grey : Housing, printed Frame with serial number Battery door, printed Filters front, 4pcs Filters back, 4 pcs Filter box complete mic, front Filter box complete mic, back Page 8 of

9 Part list hearing instrument complete and dummies HI complete, all colours: Part No. Black Medium blonde Metallic Marble grey White Dummies HI complete, all colours: Part No. Black Medium blonde Metallic Marble grey White Page 9 of

10 Part list Item : Left side Part No. Item : Right side Part No. Blisterpack 0A-L Sound tube, x-small deep (code 0A) Blisterpack 0A-R Sound tube, x-small deep (code 0A) Blisterpack A-L Sound tube, small deep (code A) Blisterpack A-R Sound tube, small deep (code A) Blisterpack 2A-L Sound tube, medium deep (code 2A) Blisterpack 2A-R Sound tube, medium deep (code 2A) Blisterpack A-L Sound tube, large deep (code A) Blisterpack A-R Sound tube, large deep (code A) Blister pack 0B-L Sound tube, x-small low (code 0B) Blister pack 0B-R Sound tube, x-small low (code 0B) Blister pack B-L Soun tube, small low (code B) Blister pack B-R Soun tube, small low (code B) Blister pack 2B-L Soun tube, mediun low (code 2B) Blister pack 2B-R Soun tube, mediun low (code 2B) Blisterpack B-L Sound tube, large low (code B) Blisterpack B-R Sound tube, large low (code B) One Blisterpack contains: 5 pcs. sound tubes p/n 59260x (R) or 59270x (L) and 2 pcs.tube cleaner p/n Page 0 of

11 Part list Domes Item Qty Part No. Bag with Dome 7 Bag with Dome 0 Bag with Dome 7 Bag with Dome 0 Bag with Dome Marked with e.g. 2B (medium low) Dome Tube length: Tube insertion depth: Tube code: Extra small Extra small Short Short Medium Medium Long Long Deep Low Deep Low Deep Low Deep Low 0A 0B A B 2A 2B A B p/n , pcs. p/n , 25 pcs. Page of

12 Part list Item Qty Part No. Dispenser tool box Containing : Front fi lter box with blonde fi lter Front fi lter box with grey fi lter Front fi lter box with white fi lter Front fi lter box with black filter Back fi lter box with blonde filter Back fi lter box with white fi lter Back fi lter box with grey fi lter Back fi lter box with black fi lter Colour marker, red, bag with 25 pcs. Colour marker, blue, bag with 25 pcs. Dummy, Beltone, mdm. blonde Cleaning brush 2CC adapter Fonix test tube straight medium deep Measuring sound tube TBS 25/IA Cutter Measurement tool Empty dispenser tool box: p/n 5800 Overwiev dispenser tool box: p/n Tool box instruction booklet: p/n Page 2 of

13 Part list Item Qty Part No. Dispenser ear box Containing : Right Xtra small deep Right Xtra small low Right small deep Right small low Right medium deep Right medium low Right large deep Right large low Left Xtra small deep Left Xtra small low Left small deep Left small low Left medium deep Left medium low Left large deep Left large low Dome 7 Dome 0 Dome Empty ear box: p/n 5700 Overwiev ear box: p/n Page of

14 Diagram Power Sig. 2 Microphone AGND H2 H7 M2 Power H H M2 sig H4 H TC H5 H H6 H TC H8 AGND H H H7 H Aux T V H7 H H2 H4 H5 H6 H8 H C 22nF C2 22nF AGND AGND U VREG MIC MICc MIC2 MIC2c TC TC2 AUX 6 Coyote2 AD2 SCL V2BAT SDA 2 5 VBAT AGND GND 7 V2BAT VREF 2 FSYS LKCLK ADDAT RESET LOBAT T V C6.0uF C5 8pF H5 C.0uF T V C4 220nF L 0uH GND U LFCLK ADDAT RESET SDA SCL SENSE V2BAT SENSE 7 VBAT SENSE2 4 Coyote2 DSP2 SENSE 5 20 DCAP SENSE4 6 2 DCAP2 9 FSYS 8 IIS_BCK 7 IIS_WS VREG 8 6 IIS_DATA GND GND OUTN 2 OUTP 9 C_COMP GNDPWR 0 T V H6 C8.0uF H5 H4 H + C7 4.7uF H5 H6 H5 H4 H +. Vbat N P Receiver R 0K R2 0K U V2BAT T V 8 Vcc A0 2 A NC 28kb EEPROM GND SDA SCL WP H8 H5 H9 H0 H H2 All test points are measured to negative battery spring. H8 Data H5 2 GND H9 Clk H H0 H H H H2 pin flex connector Page 4 of

15 Programming cables Programming cable CS6 ( pin) Flex strip Flex strip Battery pill must be used e.g. p/n Connect the flex to the programming cable by using the flex end marked with an arrow. Programming cable CS6 p/n 7-00 Flex strip for CS6 p/n 7-0. Programming cable CS44 p/n , blue (L) p/n , red (R) Flex adapter CS44 (incl. a flex strip) p/n Page 5 of

16 How to separate the instrument Back microphone fi lter Front microphone fi lter Battery door 2 pins Push the pins slightly out from one side with a pin tool p/n and pull them out using e.g. a pair of tweezers. Take out the battery door and the microphone fi lters. Note: Filters must to be exchanged every time. See further instructions on page 24 Push carefully on the stud and pull out the frame from the housing. Casco/glue Casco/glue p/n Frame assembled Page 6 of

17 Amplifier assembly H8/MIC- H2/MIC IN H9/BAT(-) H0 H2 H H4/REC(+) H7/MIC+ H/REC(-) H H6/BAT(+) H H4 H5 H9 H8 Contact module points Page 7 of

18 Amplifier Assembly Solder red wire from positive battery spring. Negative spring is shown on the frame assembly (see page 20) Wire red 8mm, p/n BAT(-) Wire amber 9 mm, p/n Wire green 9 mm, p/n Wire blue 9 mm, p/n Dip the hybrid in EGC-700 p/n and keep it for 5 seconds. Let dry for 5 seconds and repeat the process. Page 8 of

19 Microphone complete Wire, amber 2 mm p/n Wire, green 2 mm p/n front mic suspension back mic suspension. Wire, red 2 mm p/n Make sure that the suspensions fit well to the sound studs/ports on the microphones. Make sure that wire insulation is undamaged. Brush EGC-700 coating to the solder points and let dry for 5 sec - then brush once more. Page 9 of

20 Receiver complete _ + 2 Green wire, 6 mm p/n Red wire, 6 mm p/n Suspension p/n Pull the receiver through the suspension as shown and press it to the front of the suspension. Make sure the receiver is well fi tted. Brush EGC-700 coating to the solder points. Let dry for 5 sec. and brush once more. Page 20 of

21 Frame assembly 2 Insert sound outlet (p/n ). Push until click-stop. Ensure that the fl at side of the sound outlet is correctly aligned with the frame. Wire green mm p/n Insert negative battery spring. Guide the wire carefully through the hole in the frame and press the spring into place. Page 2 of

22 Coating instructions amplifier Molykote Add molykote in the area indicated by dotted lines. Molykote Cover the pins of the contact module at the solder points. Press it under the contact pins to ensure good protection. Molykote Molykote Fill the holes at the battery solder points with Molykote FS 292 p/n Wipe the surplus Molykote off to prevent soiling of the housing at fi nal assembly. Page 22 of

23 How to place filters - front and back Remove the old filter by turning the tool upside down - turn it approx. 0 0 and pull Front filters This end to be used when removing the old filter. Line up max. 4 instruments into the front fi lter box (p/n 5690x) Turn the filter box with the instruments in an upright position. Press the filters into the instruments one after the other, using the pin from the box.(same pin as from the back filter box) Back filters Press the filters into the instruments one after the other, using the pin from the box. (Same pin as from the front filter box) See also photo on page 27 Line up max. 4 instruments and place the back fi lter box (p/n 54460x) on top of the instruments. Page 2 of

24 Instrument complete in housing Colour marker red/blue Page 24 of

25 Service tool Hole for mic Hole for hybrid Hole for contact module Hole for rec Room for battery. When testing, push battery between the two battery springs Service tool p/n Page 25 of

26 Accessories p/n , pcs. p/n , 25 pcs. Magnet Filter box complete mic. front mdm. blonde *p/n Pin removal tool, p/n Cleaning brush p/n Filter box complete mic. back mdm. blonde *p/n * for p/n other colours - please look at page 9 Measurement tool p/n One side blue (left), the other side red (right) Colour marker, Red p/n , 25 pcs Blue p/n 57560, 25 pcs Page 26 of

27 Measurement tool and dome Size and 2 Size 0 Measurement tool p/n One side blue (left), the other side red (right) Place measurement tool as shown in the picture. Choose the one of the sightlines that will fit the upper side of the ear channel. Note the marking of the sightline. In this example, is the right choice. For binaural fi ttings, repeat the measurement on the left ear (there can be a difference in ear sizes, hence the tube lengths). To put the dome onto the sound tube, push the dome as far onto the sound tube as possible. It should touch the plastic ring. Page 27 of

28 How to place/remove the colour marker How to place the colour marker: Place the colour Size marker and as 2 long into the hole as possible and then pressure on the back of the marker Size 0 with a finger and in the same time turn the pin around until it breaks of. Pressure here with a finger Turn the pin around How to remove the colour marker: Push out the pin a / of its length using the pin removal tool p/n and turn the device as if it was placed on the ear and the colour marker should fall out. If the colour marker is not falling out, the battery door can be opened and from the inside the colour marker can be pushed out. The pin is pushed out Push the colour marker from inside Page 28 of

29 Test equipment Size and 2 Size 0 Test fi xture p/n Snap-in adaptor p/n To be used with Otometrics 2cc coupler. (for DSA 5000 test systems) Measuring sound tube, Bended p/n Page 29 of

30 Placing and adjusting test fixture The test fixture must be placed in the The upper part of the test fi xture can test chamber as shown in the picure. be by adjusted by loosening the two Size and 2 Size 0 screws. This is must be done when using the fi xture the first time or on a frequently basis to ensure optimal testing! Position the uppear part so that the test tube is right above the white dot in the center of the green circle. Page 0 of

31 Testing Size and 2 Size 0 Attache the coupler and HI to the test fi xture. Then connect the fl ex strip and the battery adaptor. Due to the directional microphone in EDGE E65 the use of test fixture is mandatory for AUDIOmaster testing. Instruments must be placed exactly as shown in the picture. Page of

Technical Manual Canta 770-D/470-D & 270/270-D

Technical Manual Canta 770-D/470-D & 270/270-D Technical Manual Canta 770-D/470-D & 270/270-D (including 770-D & 470-D Open BTE features) GN ReSound as Global Technical Operations gto.gnresound.com Lautrupbjerg 9 DK-2750 Ballerup Denmark Phone: + 45

More information

Technical Manual Canta 730/ /230 VC & Canta 730-OC/430-OC 730-D ITC

Technical Manual Canta 730/ /230 VC & Canta 730-OC/430-OC 730-D ITC Technical Manual Canta 730/430 230/230 VC & Canta 730-OC/430-OC 730-D ITC GN ReSound as Global Technical Operations gto.gnresound.com Lautrupbjerg 9 DK-2750 Ballerup Denmark Phone: + 45 45 75 23 16 E-Mail:

More information

Technical Manual Pixel Mini BTE PL60-DI

Technical Manual Pixel Mini BTE PL60-DI Technical Manual Pixel Mini BTE PL60-DI GN ReSound as Global Technical Operations gto.gnresound.com Lautrupbjerg 7-11 DK-2750 Ballerup Denmark Phone: + 45 45 75 23 16 E-mail: Service@gnresound.dk Table

More information

Technical Manual Beltone MARQ. Global Technical Operations gto.gnresound.com Lautrupbjerg 9 DK-2750 Ballerup Denmark

Technical Manual Beltone MARQ. Global Technical Operations gto.gnresound.com Lautrupbjerg 9 DK-2750 Ballerup Denmark Technical Manual Beltone MARQ Global Technical Operations gto.gnresound.com Lautrupbjerg 9 DK-2750 Ballerup Denmark E-Mail: Service@Beltone.com Table of Contents Description...3 Matrix & product information...4

More information

Technical Manual ReSound Metrix MX70-D/DI/DV/DVI/ MX80-DVI BTE

Technical Manual ReSound Metrix MX70-D/DI/DV/DVI/ MX80-DVI BTE Technical Manual ReSound Metrix MX70-D/DI/DV/DVI/ MX80-DVI BTE GN ReSound as Global Technical Operations gto.gnresound.com Lautrupbjerg 9 DK-2750 Ballerup Denmark E-mail: Service@gnresound.dk Table of

More information

Technical Manual INT START BTE. Global Technical Operations gto.gnresound.com Lautrubjerg 7 DK-2750 Ballerup Denmark

Technical Manual INT START BTE. Global Technical Operations gto.gnresound.com Lautrubjerg 7 DK-2750 Ballerup Denmark Technical Manual INT START BTE Global Technical Operations gto.gnresound.com Lautrubjerg 7 DK-2750 Ballerup Denmark E-Mail: Service@gnresound.dk Table of Contents SA70 & SA70-D: Page Description... 3 Part

More information

Technical Manual Beltone Paris Platform BTE

Technical Manual Beltone Paris Platform BTE Technical Manual Beltone Paris Platform BTE Global Technical Operations gto.gnresound.com Lautrupbjerg 7 DK-2750 Ballerup Denmark E-Mail: Service@Beltone.com Table of Contents Form-Factor-Matrix...3 Colour

More information

Technical Manual ReSound Match ITC. GN ReSound as Global Technical Operations Lautrupbjerg 7 DK-2750 Ballerup Denmark

Technical Manual ReSound Match ITC. GN ReSound as Global Technical Operations Lautrupbjerg 7 DK-2750 Ballerup Denmark Technical Manual ReSound Match ITC GN ReSound as Global Technical Operations Lautrupbjerg 7 DK-2750 Ballerup Denmark E-Mail: Service@gnresound.dk Table of contents Subject Page Matrix... 3 Spare Part List...

More information

Technical Manual ReSound Match ITE. GN ReSound as Global Technical Operations Lautrupbjerg 7 DK-2750 Ballerup Denmark

Technical Manual ReSound Match ITE. GN ReSound as Global Technical Operations Lautrupbjerg 7 DK-2750 Ballerup Denmark Technical Manual ReSound Match ITE GN ReSound as Global Technical Operations Lautrupbjerg 7 DK-2750 Ballerup Denmark E-Mail: Service@gnresound.dk Table of contents Subject Page Matrix... 3 Spare Part List...

More information

Beltone A/S Global Technical Operations Lautrupbjerg 7 DK-2750 Ballerup Denmark. Technical Manual Beltone DELHI Platform

Beltone A/S Global Technical Operations  Lautrupbjerg 7 DK-2750 Ballerup Denmark. Technical Manual Beltone DELHI Platform Beltone A/S Global Technical Operations http://gto.gnresound.com Lautrupbjerg 7 DK-2750 Ballerup Denmark Technical Manual Beltone DELHI Platform Table of Contents Form-Factor-Matrix & Product information...

More information

ACS75, ACS75D, ACS85 & ACS85D BTE Overview. GTO September 2006 / May 2007

ACS75, ACS75D, ACS85 & ACS85D BTE Overview. GTO September 2006 / May 2007 ACS75, ACS75D, ACS85 & ACS85D BTE Overview GTO September 2006 / May 2007 ACS75 & ACS75D ACS75 ACS75D Disassembly Pull out the soundhook from the BTE housing. Disassembly Squeeze to grip Open the battery

More information

Technical Manual ReSound TrimFlex ITC

Technical Manual ReSound TrimFlex ITC Technical Manual ReSound TrimFlex ITC GN ReSound as Global Technical Operations gto.gnresound.com Lautrupbjerg 7 DK-2750 Ballerup Denmark E-Mail: Service@gnresound.dk Table of Contents Description...3

More information

Product Information NANO

Product Information NANO Product Information NANO Nano is a hearing aid, suitable for users with a wide range of hearing losses. Nano features the Audina proprietary Audio Efficiency technology that incorporates first-class features

More information

UNCONTROLLED COPY IF PRINTED. Service Information

UNCONTROLLED COPY IF PRINTED. Service Information Service Information This document has been produced for the service departments of the Unitron Hearing group companies and agents. It is reserved for Unitron Hearing Service Centers and for trained, authorized

More information

Go Pro rationale The world s most well known rationale NAL-NL1 is implemented in Go Pro.

Go Pro rationale The world s most well known rationale NAL-NL1 is implemented in Go Pro. PRODUCT INFORMATION Go Pro sets a new standard for basic hearing care. A strong feature set makes Go Pro the most straight forward hearing instrument at an affordable price. The wide range of styles, features

More information

Technical Support and Education/ Quality control

Technical Support and Education/ Quality control Innovations in speech intelligibility High fidelity natural sound Technical Support and Education/ Quality control Psychological comfort Wearing comfort Quality Control Agenda Listening inspection Functional

More information

Product Information JUNA 9 7

Product Information JUNA 9 7 Product Information JUNA 9 7 Juna is a complete family of hearing aids, suitable for users with mild to severe hearing losses. Juna custom instruments come with more power and additional wireless functionality

More information

DESCRIPTION Behind-The-Ear air conduction hearing aid (BTE), Battery 13, programmable through fitting software, WDRC strategy.

DESCRIPTION Behind-The-Ear air conduction hearing aid (BTE), Battery 13, programmable through fitting software, WDRC strategy. Measurements performed using a UPL 66 (Rohde & Schwarz Id 6 test unit on May 06 and are subject to changes without prior notice. Features Matrix 7/ @ cc 00% Digital Technology Digitally Programmable Programs

More information

Specification Guide. Cheer

Specification Guide. Cheer Cheer Specification Guide Sonic presents Cheer, a well-rounded lineup of products featuring impressive sound quality stats. Cheer offers three technology levels, so there s a device for nearly every hearing

More information

Fitting range

Fitting range P R O D U C T I N F O R M A T I O N Fitting range HL - 0 CIC/MIC ITC ITE/ITE D ITE P (312) BTE/BTED/ ITE P (13) BTE P 125Hz 2 0 0 00 00 00 Product Concept Atlas Plus offers a full family of high quality

More information

Specification Guide. Celebrate

Specification Guide. Celebrate Celebrate Specification Guide Designed with the people and events of everyday lifestyles in mind, Celebrate rises to any occasion. Sounds are clear and natural thanks to the robust Sonic Speech Variable

More information

Product Information SAPHIRA 3

Product Information SAPHIRA 3 Product Information SAPHIRA 3 The Saphira 3 is an impressive mid-range hearing aid suitable for a wide range of hearing losses. With Saphira 3, Costco members will experience high-tech features that bring

More information

Product Information Pico RITE

Product Information Pico RITE Pico RITE Product Information Pico RITE Pico RITE is a tiny receiver-in-the-ear hearing aid, suitable for users with mild to profound hearing losses. Pico RITE comes with the minifit speaker and dome system,

More information

Fitting Guide BEHIND-THE-EAR HEARING INSTRUMENTS. Compact Power Plus BTE Compact Power BTE Micro BTE Power BTE Nano BTE

Fitting Guide BEHIND-THE-EAR HEARING INSTRUMENTS. Compact Power Plus BTE Compact Power BTE Micro BTE Power BTE Nano BTE Fitting Guide BEHIND-THE-EAR HEARING INSTRUMENTS Compact Power Plus BTE Compact Power BTE Micro BTE Power BTE Nano BTE COMPACT POWER PLUS, COMPACT POWER, MICRO, POWER, NANO Fitting Guide Compact Power

More information

NEVARA 1. Product Information

NEVARA 1. Product Information Product Information NEVARA 1 Nevara is a hearing instrument family with a remarkable basic feature set and remote control capability. The range of BTE, RITE, and ITE models offers lots of fitting options

More information

User groups Most sensorineural and conductive hearing losses from mild to profound People with high demands on ergonomics

User groups Most sensorineural and conductive hearing losses from mild to profound People with high demands on ergonomics Product Information Swift +. Swift +. Swift + Fitting Ranges Swift + Swift + Swift + Swift + Swift + General information Swift is a range of 3 high quality, programmable, cosmetically attractive BTE instruments.

More information

PRODUCT INFORMATION FITTING INFORMATION TECHNICAL INFORMATION

PRODUCT INFORMATION FITTING INFORMATION TECHNICAL INFORMATION PRODUCT INFORMATION FITTING INFORMATION TECHNICAL INFORMATION PRODUCT INFORMATION DecisionMaker DecisionMaker orchestrates the directionality and noise management systems in Tego. Using AI processing techniques,

More information

Charge&Go Nx. Pure. Technical Data. 7Nx 5Nx 3Nx. S-Receiver. M-Receiver. P-Receiver. HP-Receiver

Charge&Go Nx. Pure. Technical Data. 7Nx 5Nx 3Nx. S-Receiver. M-Receiver. P-Receiver. HP-Receiver Pure Technical Data Charge&Go Nx 7Nx 5Nx 3Nx S-Receiver 56 db / 119 db SPL (ear simulator) 45 db / 108 db SPL (2 ccm coupler) M-Receiver 70 db / 129 db SPL (ear simulator) 60 db / 119 db SPL (2 ccm coupler)

More information

Product Information PICO RITE

Product Information PICO RITE Product Information PICO RITE Pico RITE is a tiny receiver-in-the-ear hearing aid, suitable for users with mild to profound hearing losses. Pico RITE comes with the minifit speaker and dome system, including

More information

Models WH30TQG and WH30XLR User Guide MODEL WH30 CONDENSER HEADSET MICROPHONE

Models WH30TQG and WH30XLR User Guide MODEL WH30 CONDENSER HEADSET MICROPHONE Models WH30TQG and WH30XLR User Guide MODEL WH30 CONDENSER HEADSET MICROPHONE WH30XLR ONLY 2001, Shure Incorporated 27C3121 (AF) Printed in Mexico INTRODUCTION The Shure Model WH30 is a light yet rugged

More information

Service & Maintenance

Service & Maintenance Service & Maintenance Internal Amplifier External (Peavey) Amplifier Core & HDD Monitor UPS Dollar Bill Acceptor Coin Mechanism Cleaning Fans & Filter G1-1 Internal Amplifier Amplifier Removal 1. Disconnect

More information

Mac mini Mid 2011 Hard Drive Replacement

Mac mini Mid 2011 Hard Drive Replacement Replace your Mac mini's Mid 2011 hard drive for more storage space. Written By: Walter Galan ifixit CC BY-NC-SA www.ifixit.com Page 1 of 15 INTRODUCTION Use this guide to completely replace your mini's

More information

MACRO MODCHIP FOR XBOX360 CG2 INSTALLATION INSTRUCTIONS

MACRO MODCHIP FOR XBOX360 CG2 INSTALLATION INSTRUCTIONS MACRO MODCHIP FOR XBOX360 CG2 INSTALLATION INSTRUCTIONS List of tools and materials needed: Modchip, flexible LED add-on board, 6 tac switches Microsoft wireless CG2 controller Soldering iron and thin

More information

Front-door station series for surface-mounting Profi-Economic PES Profi-Design PDS

Front-door station series for surface-mounting Profi-Economic PES Profi-Design PDS Product information Front-door station series for surface-mounting Profi-Economic PES Profi-Design PDS PI_GB_PES_PDS_Art0015689_1v0.doc 2 10/2005 In Table of contents Scope of delivery...3 Safety notices...3

More information

Wiring Inside the card reader you will see a circuit board. The connections are as follows:

Wiring Inside the card reader you will see a circuit board. The connections are as follows: Power Adaptor (12VDC, Max. Current: 1A) If you purchased the Cardlock Series power supply cut the head of the adaptor and strip the insulation. If your locking mechanism, electric strike or magnetic lock

More information

Pure 312 Nx. Technical Data. 7Nx 5Nx 3Nx. S-Receiver. M-Receiver. P-Receiver. HP-Receiver

Pure 312 Nx. Technical Data. 7Nx 5Nx 3Nx. S-Receiver. M-Receiver. P-Receiver. HP-Receiver Pure 312 Nx Technical Data 7Nx 5Nx 3Nx S-Receiver 56 db / 119 db SPL (ear simulator) 45 db / 108 db SPL (2 ccm coupler) M-Receiver 70 db / 129 db SPL (ear simulator) 60 db / 119 db SPL (2 ccm coupler)

More information

Ace primax. Technical Data. P-Receiver 70 db / 126 db SPL (ear simulator) 60 db / 118 db SPL (2 ccm coupler)

Ace primax. Technical Data. P-Receiver 70 db / 126 db SPL (ear simulator) 60 db / 118 db SPL (2 ccm coupler) Ace primax Technical Data 7px X 5px X 3px X S-Receiver 55 db / 118 db SPL (ear simulator) 45 db / 108 db SPL (2 ccm coupler) M-Receiver 65 db / 123 db SPL (ear simulator) 55 db / 113 db SPL (2 ccm coupler)

More information

TH Premium/Advanced Custom 19

TH Premium/Advanced Custom 19 TH Premium/Advanced Custom 19 Technical Data ITE ITC/HS CIC IIC 118/55 55 db / 118 (2 ccm coupler) 65 db / 128 (ear simulator) 113/50 50 db / 113 (2 ccm coupler) 61 db / 124 (ear simulator) 113/50 50 db

More information

Data Sheet RIC-4400 RIC-4400 DK: USA: PRC: NL: Version: Page 1 of 13

Data Sheet RIC-4400 RIC-4400 DK: USA: PRC: NL: Version: Page 1 of 13 - DS Page 1 of 13 2 4 5 3 1 Features Generic RIC module for mild gain hearing loss Low vibration high gain 4400 dual receiver Future proof CS8X plug/socket with 8 terminals State-of-the-art receiver housing

More information

Pacific Antenna Two Tone Generator

Pacific Antenna Two Tone Generator Pacific Antenna Two Tone Generator Description Our Two Tone Generator kit provides two non-harmonic, sine wave signals for testing audio circuits Outputs of approximately 700Hz and 1900Hz and the combination

More information

Digital Keypad Introduction

Digital Keypad  Introduction K2 Digital Keypad Introduction The K02 uses the latest microprocessor technology to operate door strikes and security systems that require a momentary (timed) or latching dry contact closure. All programming

More information

Removing and Replacing Parts

Removing and Replacing Parts Removing and Replacing Parts Preparing to Work Inside the Computer Recommended Tools Screw Identification System Components Hard Drive Fixed Optical Drive Media Bay Devices Memory Modules Mini PCI Card

More information

Gateway Profile 4 service guide

Gateway Profile 4 service guide Gateway Profile 4 service guide Customizing Troubleshooting Contents Replacing Components in Your Gateway Profile 4.................. 1 About this guide.....................................................

More information

BuffaloLabs WiFi Lantern Assembly guide version 1

BuffaloLabs WiFi Lantern Assembly guide version 1 BuffaloLabs WiFi Lantern Assembly guide version 1 Needed equipment: Solder iron Solder wire Cutter Wire stripper (optional) Hot glue gun Overview of the components (not including USB cable and box panels)

More information

SOUND LEVEL CALIBRATOR DVM1356 INSTRUCTION MANUAL HANDLEIDING MANUEL D UTILISATEUR DVM1356 SOUND LEVEL CALIBRATOR 1

SOUND LEVEL CALIBRATOR DVM1356 INSTRUCTION MANUAL HANDLEIDING MANUEL D UTILISATEUR DVM1356 SOUND LEVEL CALIBRATOR 1 SOUND LEVEL CALIBRATOR DVM1356 INSTRUCTION MANUAL HANDLEIDING MANUEL D UTILISATEUR DVM1356 SOUND LEVEL CALIBRATOR 1 SAFETY INFORMATION l Read the following safety information carefully before attempting

More information

ibook G4 14" 933 MHz-1.33 GHz Hard Drive

ibook G4 14 933 MHz-1.33 GHz Hard Drive ibook G4 14" 933 MHz-1.33 GHz Hard Drive Replacement Written By: irobot ifixit CC BY-NC-SA www.ifixit.com Page 1 of 25 INTRODUCTION You can install hard drives up to 9.5mm thick. TOOLS: Coin (1) Phillips

More information

Drive 3G-S ENGLISH. Cellular Signal Booster A Customer Support: Mon-Fri 8 am to 6 pm.

Drive 3G-S ENGLISH. Cellular Signal Booster A Customer Support: Mon-Fri 8 am to 6 pm. ENGLISH Drive 3G-S Cellular Signal Booster A512626 ENGLISH!! IT IS VERY IMPORTANT TO POWER YOUR SIGNAL BOOSTER USING A SURGE PROTECTED AC POWER STRIP WITH AT LEAST A 1000 JOULE RATING. FAILURE TO DO THIS

More information

3 Click. Intuis. Technical Data ITC CIC. 65 db / 127 db SPL (ear simulator) 55 db / 116 db SPL (2 ccm coupler)

3 Click. Intuis. Technical Data ITC CIC. 65 db / 127 db SPL (ear simulator) 55 db / 116 db SPL (2 ccm coupler) Intuis Technical Data 3 Click ITC 65 db / 127 db SPL (ear simulator) 55 db / 116 db SPL (2 ccm coupler) CIC 61 db / 124 db SPL (ear simulator) 50 db / 113 db SPL (2 ccm coupler) Hearing Systems Intuis

More information

Canon Powershot A720 IS Motherboard Replacement

Canon Powershot A720 IS Motherboard Replacement Canon Powershot A720 IS Motherboard Replacement This guide will show how to replace the motherboard. Written By: Jamie ifixit CC BY-NC-SA www.ifixit.com Page 1 of 16 INTRODUCTION This guide will allow

More information

Mac mini Mid 2011 IR Sensor Replacement

Mac mini Mid 2011 IR Sensor Replacement Replace a broken IR sensor/sleep LED. Written By: Walter Galan ifixit CC BY-NC-SA www.ifixit.com Page 1 of 19 INTRODUCTION Use this guide to replace your mini's IR sensor/sleep LED assembly. Replacing

More information

PERSONAL SOUND In-Ear Amplifier PS2500AMP

PERSONAL SOUND In-Ear Amplifier PS2500AMP PERSONAL SOUND In-Ear Amplifier PS2500AMP User Guide Table of Contents Your PERSONAL SOUND In-Ear Amplifier 4-5 Turning the Device On / Off 6 PERSONAL SOUND In-Ear Amplifier PS2500AMP Thank you for choosing

More information

ASUS D550MA-DS01 Motherboard

ASUS D550MA-DS01 Motherboard ASUS D550MA-DS01 Motherboard Replacement This guide will show you how to remove the motherboard from the laptop. Steps included in this process are removing the screws, disconnecting cables, and removing

More information

You need the following components to assemble the Black n Wood Nixie Clock circuit board:

You need the following components to assemble the Black n Wood Nixie Clock circuit board: You need the following components to assemble the Black n Wood Nixie Clock circuit board: Quantity Designator Description 1 Battery Battery, CR1220 1 Battery Battery holder 3 Button 1, Button 2, Button

More information

OnePlus 5 Screen and Digitizer Assembly Replacement

OnePlus 5 Screen and Digitizer Assembly Replacement OnePlus 5 Screen and Digitizer Assembly Replacement Follow this guide to replace the screen and digitizer for the OnePlus 5. This replaces the screen as well as the frame it is attached to. Written By:

More information

Written By: Walter Galan

Written By: Walter Galan Replace a cracked screen on your iphone 4S. Written By: Walter Galan ifixit CC BY-NC-SA www.ifixit.com Page 1 of 32 INTRODUCTION Use this guide to replace the screen on your iphone 4S. After successfully

More information

ODU MINI-SNAP PC Product Description. ODU MINI-SNAP PC: The Connector with Push-Pull-Locking in Plastic

ODU MINI-SNAP PC Product Description. ODU MINI-SNAP PC: The Connector with Push-Pull-Locking in Plastic ODU MINI-SNAP PC Product Description ODU MINI-SNAP PC: The Connector with Push-Pull-Locking in Plastic Cylindrical Connectors are generally available with several locking mechanisms: The most frequently

More information

SV 33 Acoustic calibrator

SV 33 Acoustic calibrator INSTRUMENTATION FOR SOUND AND VIBRATION MEASUREMENTS SV 33 Acoustic calibrator User s manual Warsaw, 17 June, 2014 SVANTEK Sp. z o.o. www.svantek.com e-mail: office @ svantek.com.pl 02-872 Warszawa, ul.

More information

PS 430 FOUR CHANNEL REMOTE SPEAKER STATION. User Manual. January 2017 V1.0

PS 430 FOUR CHANNEL REMOTE SPEAKER STATION. User Manual. January 2017 V1.0 PS 430 FOUR CHANNEL REMOTE SPEAKER STATION User Manual January 2017 V1.0 Table of contents 1.0 GENERAL DESCRIPTION... 3 2.0 INSTALLATION... 4 3.0 FRONTPANEL CONTROLS & CONNECTORS... 4 4.0 SIDE PANEL CONNECTORS...

More information

NS-AP8600/SPS-8600 HOME CINEMA SPEAKER PACKAGE OWNER S MANUAL CONTENTS

NS-AP8600/SPS-8600 HOME CINEMA SPEAKER PACKAGE OWNER S MANUAL CONTENTS HOME CINEMA SPEAKER PACKAGE CONTENTS CONSUMER PRECAUTIONS... 2 UNPACKING... 3 ACCESSORIES... 4 SETTING UP THE SPEAKERS... 5 CONNECTIONS TO THE RECEIVER... 10 SPEAKER PLACEMENT... 11 SPECIFICATIONS... 11

More information

ibook G3 14" Hard Drive Replacement

ibook G3 14 Hard Drive Replacement Written By: irobot ifixit CC BY-NC-SA www.ifixit.com Page 1 of 20 INTRODUCTION How to remove the hard drive and its bracket from your computer. TOOLS: Coin (1) Paper Clip (1) Phillips #00 Screwdriver (1)

More information

USER MANUAL SV 35 ACOUSTIC CALIBRATOR. Copyright 2015 SVANTEK. All rights reserved.

USER MANUAL SV 35 ACOUSTIC CALIBRATOR. Copyright 2015 SVANTEK. All rights reserved. USER MANUAL SV 35 ACOUSTIC CALIBRATOR Warsaw, January 2016 Copyright 2015 SVANTEK. All rights reserved. 2 SV 35 User Manual Contents 1. Introduction... 3 2. Acoustic calibrator SV 35... 3 2.1. General

More information

Written By: Brittany K

Written By: Brittany K Nintendo DS Lite Motherboard Replacement Written By: Brittany K ifixit CC BY-NC-SA www.ifixit.com Page 1 of 11 INTRODUCTION This guide has been updated by ifixit staff! Read the new, official guide here.

More information

Landmark Upgrade Kit Installation Instructions

Landmark Upgrade Kit Installation Instructions Landmark Upgrade Kit Installation Instructions REMOVING THE LANDMARK BOARD 1 REMOVE POWER FROM UNIT. 2 Disconnect ALL board connections by removing the associated blue blocks (see Figure 1). Include the

More information

PS 230 DUAL CHANNEL REMOTE SPEAKER STATION. User Manual. January 2017 V1.0

PS 230 DUAL CHANNEL REMOTE SPEAKER STATION. User Manual. January 2017 V1.0 PS 230 DUAL CHANNEL REMOTE SPEAKER STATION User Manual January 2017 V1.0 Table of contents 1.0 GENERAL DESCRIPTION... 3 2.0 INSTALLATION... 4 3.0 FRONTPANEL CONTROLS & CONNECTORS... 4 4.0 SIDE PANEL CONNECTORS...

More information

Sound Level Calibrator. CAL601 CLASS 1 User s Manual

Sound Level Calibrator. CAL601 CLASS 1 User s Manual Sound Level Calibrator CAL601 CLASS 1 User s Manual Contents: 1. INTRODUCTION... 2 2. EQUIVALENT FREE-FIELD... 2 3. SPECIFICATIONS... 2 4. OPERATING INSTRUCTIONS... 3 5. CALIBRATION AND ADJUSTMENT...

More information

P r o d u c t I n f o R M A T I O N - h i t p r o / h i t

P r o d u c t I n f o R M A T I O N - h i t p r o / h i t P r o d u c t I n f o R M A T I O N - h i t p r o / h i t Oticon Hit is a family of reliable, great sounding hearing instruments in the mid-to-low priced market. Powered by Oticon s RISE platform, featuring

More information

OPERATING INSTRUCTION

OPERATING INSTRUCTION OPERATING INSTRUCTION AUTORANGING MULTIMETER MAX Ω F C 10A MAX every 15 min. COM V SAFETY INFORMATION The following safety information must be observed to insure maximum personal safety during the operation

More information

CONTENTS Safety Information Description Features Specifications Nomenclature And Function Operating Preparation Calibration Procedure

CONTENTS Safety Information Description Features Specifications Nomenclature And Function Operating Preparation Calibration Procedure CONTENTS Title Page 1. Safety Information.. 1 Environment Conditions. 1 Maintenance & Clearing. 1 Safety symbols 1 2. Description.. 2 3. Features.....2 4. Specifications...... 2 Output sound pressure levels...

More information

Toshiba Satellite L305-S5946 Power Jack Replacement

Toshiba Satellite L305-S5946 Power Jack Replacement Toshiba Satellite L305-S5946 Power Jack Replacement Replace the power jack in your Toshiba Satellite L305-S5946. Written By: Michael Erberich ifixit CC BY-NC-SA www.ifixit.com Page 1 of 16 INTRODUCTION

More information

TA12 full-rangespeaker. user manual

TA12 full-rangespeaker. user manual TA12 full-rangespeaker user manual Musikhaus Thomann e.k. Treppendorf 30 96138 Burgebrach Germany Telephone: +49 (0) 9546 9223-0 email: info@thomann.de Internet: www.thomann.de 30.11.2011 Table of contents

More information

97100 NAMUR series, 3/2 & 5/2 Indirect solenoid actuated spool valve

97100 NAMUR series, 3/2 & 5/2 Indirect solenoid actuated spool valve 9700 NAMUR series, / & / > > Port size: /4 (ISO G or NPT), NAMUR Interface > > Crossover-free switching > > Main application: Single and double acting actuators > > / way valve usable as / way valve >

More information

ASUS D550MA-DS01 Screen Replacement

ASUS D550MA-DS01 Screen Replacement ASUS D550MA-DS01 Screen Replacement This guide will show you how to replace your laptop screen. Written By: Calvin Wieczorek ifixit CC BY-NC-SA www.ifixit.com Page 1 of 12 INTRODUCTION Many people will

More information

MCH WIRE HARNESS WITH QUICK DISCONNECT REPLACEMENT Initial Release 1/31/2013

MCH WIRE HARNESS WITH QUICK DISCONNECT REPLACEMENT Initial Release 1/31/2013 1. Table of Contents 1. Table of Contents Page 1 2. Remove Failed MCH-103.2 Page 1 3. Install MCH-103.2 to MCH-102NW Page 2 4. Install NC3FX-HD to MCH-103.2 Page 3 5. Install MCH-103.2 Battery Terminal

More information

GREISINGER electronic GmbH D Regenstauf, Hans-Sachs-Straße 26

GREISINGER electronic GmbH D Regenstauf, Hans-Sachs-Straße 26 E39.0.31.6C-02 Data logger for humidity temperature as of version V1.0 Operating Manual T-Logg 160 GREISINGER electronic GmbH D - 93128 Regenstauf, Hans-Sachs-Straße 26 +49 (0) 9402 / 9383-0 +49 (0) 9402

More information

Written By: Evan Noronha

Written By: Evan Noronha iphone 6s Power Button Cover Replacement Replace a faulty power button cover in an iphone 6s. Written By: Evan Noronha ifixit CC BY-NC-SA www.ifixit.com Page 1 of 36 INTRODUCTION Use this guide to remove

More information

S-14 S-14. Compact Digital Multimeter. Compact Digital Multimeter

S-14 S-14. Compact Digital Multimeter. Compact Digital Multimeter S-14 Compact Digital Multimeter S-14 Compact Digital Multimeter SAFETY INFORMATION The following safety information must be observed to insure maximum personal safety during the operation at this meter

More information

Technical Data. Highlights Enhanced signal dynamics through digital signal processing

Technical Data. Highlights Enhanced signal dynamics through digital signal processing A&M Hearing Technical Data Digitrim Gerätename 12 Custom Application Fully digital 1 channel amplifier with trimmer s Applicable for mild to moderate hearing loss Simple, flexible fitting with fitting

More information

Orbis MU 21. Digital Delegate Microphone Unit with Loudspeaker Order #

Orbis MU 21. Digital Delegate Microphone Unit with Loudspeaker Order # Digital Delegate Microphone Unit with Loudspeaker Order # 725.706 Supplied without gooseneck microphone FEATURES Coated plastic housing with metal bottom plate Inserts made of optically hardened acrylic

More information

Noise Management. Standard Features Based on the RISE technology ultra fast. A modulation-based Noise Management. System which uses a speech-weighted

Noise Management. Standard Features Based on the RISE technology ultra fast. A modulation-based Noise Management. System which uses a speech-weighted P r o d u c t I n f o R M A T I ON h i t p r o / h i t Oticon Hit is a family of reliable, great sounding hearing instruments F I TT I N G R A N G E in the midtolow priced market. Powered by Oticon s RISE

More information

Written By: Brendan Kelly

Written By: Brendan Kelly Game Boy Micro LCD Screen Replacement Written By: Brendan Kelly ifixit CC BY-NC-SA www.ifixit.com Page 1 of 13 INTRODUCTION In this guide, we'll show you how to change the LCD Screen. TOOLS: Phillips #00

More information

Game Boy Micro Motherboard Replacement

Game Boy Micro Motherboard Replacement Game Boy Micro Motherboard Replacement Written By: Brendan Kelly ifixit CC BY-NC-SA www.ifixit.com Page 1 of 12 INTRODUCTION In this guide, we will show you how to remove and replace the motherboard and

More information

ibook G4 12" 800 MHz-1.2 GHz RJ-11 Board

ibook G4 12 800 MHz-1.2 GHz RJ-11 Board ibook G4 12" 800 MHz-1.2 GHz RJ-11 Board Replacement Written By: irobot ifixit CC BY-NC-SA www.ifixit.com Page 1 of 24 INTRODUCTION The standard telephone jack port for connecting to the 56k internal modem.

More information

Shack Clock kit. U3S Rev 2 PCB 1. Introduction

Shack Clock kit. U3S Rev 2 PCB 1. Introduction Shack Clock kit U3S Rev 2 PCB 1. Introduction Thank you for purchasing the QRP Labs Shack Clock kit. This clock uses the Ultimate3S QRSS/WSPR kit hardware, but a different firmware version. It can be used

More information

Hearing-Protector Test Fixture Type 45CA

Hearing-Protector Test Fixture Type 45CA Instruction Manual Hearing-Protector Test Fixture Type 45CA G. R. A. S. SOUND & VIBRATION Skovlytoften 33, 2840 Holte, Denmark www.gras.dk gras@gras.dk Revision 28 November 2013 LI0024 CONTENTS 1 Introduction.....................................................

More information

WINSTA. Full Line Catalog 2008/2009

WINSTA. Full Line Catalog 2008/2009 WINSTA Full Line Catalog 2008/2009 5 Contents FULL LINE CATALOG W4, Volume 1 Rail-Mounted Terminal Block Systems FULL LINE CATALOG W4 Rail-Mounted Terminal Blocks Volume 1 X-COM -SYSTEM Terminal Strips

More information

Page Housing Plastic Metal Mounting DIN Rail or surface mount Panel or bracket mount Wattage Range 10W to 240W 7.5W to 240W 10W to 300W

Page Housing Plastic Metal Mounting DIN Rail or surface mount Panel or bracket mount Wattage Range 10W to 240W 7.5W to 240W 10W to 300W Selection Guide Selection Guide PS5R Slim Line PS5R PS3L Operator Interfaces Communication & Networking PLCs NEW Models Appearance Automation Software Page 107 113 118 Housing Plastic Metal Mounting DIN

More information

STAGE INTERCOM KIT 1.1 SPECIFICATION. General: The lower section is a small power amplifier designed to drive headphones or a small 8ohm speaker.

STAGE INTERCOM KIT 1.1 SPECIFICATION. General: The lower section is a small power amplifier designed to drive headphones or a small 8ohm speaker. STAGE INTERCOM KIT Version 2.1.1 - March 2018 - EduTek Ltd 1.0 DESCRIPTION This intercom module comprises of two separate circuits sharing the same supply. The upper section is a pre-amplifier designed

More information

REMOTE HEAD ADAPTER INSTALLATION GUIDE

REMOTE HEAD ADAPTER INSTALLATION GUIDE REMOTE HEAD ADAPTER INSTALLATION GUIDE The Remote Head adapter is a valuable accessory for the Uniden BC-780, 785 and 796 scanners. It allows the scanner's control panel to be removed from the radio and

More information

To connect the AC adapter:

To connect the AC adapter: Replacing the AC Adapter Replacing the AC Adapter 3 Plug the power cord into a wall outlet. The power indicator turns on. To connect the AC adapter: Connect the power cord to the AC adapter. Power indicator

More information

VE-53 Sensor Uniaxial / Triaxial Surface and Downhole Velocity Sensor. Operation Manual

VE-53 Sensor Uniaxial / Triaxial Surface and Downhole Velocity Sensor. Operation Manual VE-53 Sensor Uniaxial / Triaxial Surface and Downhole Velocity Sensor Operation Manual Company: Author: Checked: Approved: Level: Distribution: GeoSIG Ltd Wiesenstrasse 39, 8952 Schlieren, Switzerland,

More information

Strain gauge Measuring Amplifier GSV-1A8. Instruction manual GSV-1A8, GSV-1A8USB, GSV-1A16USB

Strain gauge Measuring Amplifier GSV-1A8. Instruction manual GSV-1A8, GSV-1A8USB, GSV-1A16USB Strain gauge Measuring Amplifier GSV-1A8 Instruction manual GSV-1A8, GSV-1A8USB, GSV-1A16USB GSV-1A8USB SubD1 (front side) GSV-1A8USB M12 (front side) GSV-1A16USB (rear side) GSV-1A8USB K6D (front side)

More information

Thermal-Magnetic Circuit Breaker 2216-S

Thermal-Magnetic Circuit Breaker 2216-S Thermal-Magnetic Circuit Breaker 226-S Description One and two pole thermal-magnetic circuit breaker in compact design with slide actuator, trip-free mechanism, various trip characteristics and optional

More information

Apex Tablet 7 Battery Replacement

Apex Tablet 7 Battery Replacement Apex Tablet 7 Battery Replacement This guide will instruct you on how to replace the lithium-ion battery inside the Apex 7" Tablet. Written By: Corrine Nief ifixit CC BY-NC-SA www.ifixit.com Page 1 of

More information

Product Information. DCM Standard indoor stations TK IS A 514 A.. TK IS A 514 AD.. (Design)

Product Information. DCM Standard indoor stations TK IS A 514 A.. TK IS A 514 AD.. (Design) Product Information DCM Standard indoor stations TK IS A 514 A.. TK IS A 514 AD.. (Design) ALBRECHT JUNG GMBH & CO. KG Volmestraße 1 58579 Schalksmühle Phone +49.2355.806-0 Fax +49.2355.806-189 E-Mail:

More information

Mac mini Mid 2011 Heat Sink Replacement

Mac mini Mid 2011 Heat Sink Replacement Mac mini Mid 2011 Heat Sink Replacement Replacing the mini's heat sink. Written By: Walter Galan ifixit CC BY-NC-SA www.ifixit.com Page 1 of 16 INTRODUCTION Use this guide to replace your mini's heat sink.

More information

TA18 active subwoofer. user manual

TA18 active subwoofer. user manual TA18 active subwoofer user manual Musikhaus Thomann e.k. Treppendorf 30 96138 Burgebrach Germany Telephone: +49 (0) 9546 9223-0 email: info@thomann.de Internet: www.thomann.de 30.11.2011 Table of contents

More information

Button Code Kit. Assembly Instructions and User Guide. Single Button Code Entry System

Button Code Kit. Assembly Instructions and User Guide. Single Button Code Entry System Button Code Kit Single Button Code Entry System Assembly Instructions and User Guide Rev 1.0 December 2009 www.alan-parekh.com Copyright 2009 Alan Electronic Projects Inc. 1. Introduction... 4 1.1 Concept

More information

RCD Fused Connection Unit Model: RCD10WPV. RCD Double Sockets Models: RCD05WAV, RCD06WPV, RCD07MAV, RCD08MPV. Installation & Operating Instructions

RCD Fused Connection Unit Model: RCD10WPV. RCD Double Sockets Models: RCD05WAV, RCD06WPV, RCD07MAV, RCD08MPV. Installation & Operating Instructions RCD Fused Connection Unit Model: RCD10WPV RCD Double Sockets Models: RCD05WAV, RCD06WPV, RCD07MAV, RCD08MPV Installation & Operating Instructions General The Timeguard range of RCDs provides protection

More information

The Radio Control Temperature Logger (RCTL) Manual For hardware version 1.0 Manual version 1.0b

The Radio Control Temperature Logger (RCTL) Manual For hardware version 1.0 Manual version 1.0b The Radio Control Temperature Logger (RCTL) Manual For hardware version 1.0 Manual version 1.0b All materials owned by Dan Gebhardt Introduction This device records the temperature of a model engine during

More information

Megatouch FORCE Monitor Chassis Board Replacement

Megatouch FORCE Monitor Chassis Board Replacement Megatouch FORCE Monitor Chassis Board Replacement Visit the Merit Industries, Inc. Web site http://www.meritind.com merit industries, inc. PM0337-01 Rev C Table of Contents FORCE Classic Monitor Chassis

More information