AN SC16IS760/762 Fast IrDA mode. Document information

Transcription

1 Rev June 2006 Application note Document infmation Info Keywds Abstract Content, Fast, Mbit/s, SC16C760/762, MIR, SIR This application note details the operation of the Mbit/s mode suppted by Philips Semiconducts and. It also describes the differences between this mode and the MIR mode specified by the version 1.1.

2 Revision histy Rev Date Description application note; initial version Contact infmation F additional infmation, please visit: F sales office addresses, please send an to: sales.addresses@ _1 Application note Rev June of 6

3 1. Introduction This application note details the operation of the Mbit/s mode suppted by Philips Semiconducts and, and it also describes the differences between this mode and the MIR mode specified by the version SIR and MIR standards The Physical Layer Specification sets a standard f the IR transceiver, the modulation encoding/decoding method, as well as other physical parameters. F transfer rate of 9.6 kbit/s, 19.2 kbit/s, 38.4 kbit/s, 57.6 kbit/s kbit/s operations (SIR standard) a start bit (0) and a stop bit (1) is added befe and after each byte of data. This is the same fmat as used in a traditional UART. However, instead of NRZ, a method similar to RZ is used, where a 0 is encoded as a single pulse of 3 16 of a bit cell, and a 1 is encoded as the absence of such a pulse. F transfer rate of Mbit/s Mbit/s operation (MIR standard), no start stop bits are used and the same synchronous fmat as HDLC is used. Again, a 0 is encoded as a single pulse ( 1 4 the bit cell), whereas a 1 is encoded as the absence of such a pulse. In der to ensure clock recovery, bit stuffing is used (same as in HDLC). 3. The Mbit/s and the Mbit/s speeds suppted by Philips Semiconducts and are not compatible with the industrial MIR standard. They are implemented based on the SIR standard a start and a stop bit are added to each byte, and a 0 is encoded as a single pulse of 1 4 of the bit cell, a 1 is encoded as the absence of such a pulse. The blocks of and (when programmed as either Mbit/s Mbit/s) do not have clock recovery circuitry bit stuffing function as required by the industry MIR standard. The Fast mode (speed greater than kbit/s) of the and can be used to transmit and receive data between two Philips devices. This mode allows the and the devices to communicate with each other through an link at a higher speed than those specified by the SIR standard. TRANSMIT infrared RECEIVE infrared Fig 1. Fast mode _1 Application note Rev June of 6

4 4. Abbreviations Table 1. Acronym HDLC IR MIR NRZ RZ SIR UART Abbreviations Description High-level Data Link Control Infrared Data Association InfraRed Medium-speed InfraRed Non-Return to Zero Return to Zero Standard InfraRed Universal Asynchronous Receiver/Transmitter _1 Application note Rev June of 6

5 5. Legal infmation 5.1 Definitions Draft The document is a draft version only. The content is still under internal review and subject to fmal approval, which may result in modifications additions. Philips Semiconducts does not give any representations warranties as to the accuracy completeness of infmation included herein and shall have no liability f the consequences of use of such infmation. 5.2 Disclaimers General Infmation in this document is believed to be accurate and reliable. However, Philips Semiconducts does not give any representations warranties, expressed implied, as to the accuracy completeness of such infmation and shall have no liability f the consequences of use of such infmation. Right to make changes Philips Semiconducts reserves the right to make changes to infmation published in this document, including without limitation specifications and product descriptions, at any time and without notice. This document supersedes and replaces all infmation supplied pri to the publication hereof. Suitability f use Philips Semiconducts products are not designed, authized warranted to be suitable f use in medical, military, aircraft, space life suppt equipment, n in applications where failure malfunction of a Philips Semiconducts product can reasonably be expected to result in personal injury, death severe property environmental damage. Philips Semiconducts accepts no liability f inclusion and/ use of Philips Semiconducts products in such equipment applications and therefe such inclusion and/ use is f the customer s own risk. Applications Applications that are described herein f any of these products are f illustrative purposes only. Philips Semiconducts makes no representation warranty that such applications will be suitable f the specified use without further testing modification. 5.3 Trademarks Notice: All referenced brands, product names, service names and trademarks are the property of their respective owners. _1 Application note Rev June of 6

6 6. Contents 1 Introduction SIR and MIR standards Abbreviations Legal infmation Definitions Disclaimers Trademarks Contents Please be aware that imptant notices concerning this document and the product(s) described herein, have been included in section Legal infmation. F me infmation, please visit: F sales office addresses, to: sales.addresses@ Date of release: 8 June 2006 Document identifier: _1