PowerFlex 400 Drive Firmware Version 7.01

Transcription

1 Release Notes PowerFlex 400 Drive Firmware Version 7.01 Catalog Number 22C These release notes correspond to major version 7, minor version 1 of firmware for the PowerFlex 400 drive. The following information is included in this document: Topic Page Determine the Firmware Version Level 1 Download Firmware 6 Firmware Upgrades 7 Enhancements 11 Corrected Anomalies 12 Known Anomalies 12 Determine the Firmware Version Level To determine the current firmware revision for a PowerFlex 400 drive, view parameter d320 [Control SW Ver]. Alternatively, you can also determine the firmware revision of the PowerFlex 400 drive using one of these methods: Using the External LCD HIM (22-HIM-**) on page 2 Using Connected Components Workbench Software on page 2 Using Logix Designer Software on page 3 Using DriveExplorer Lite/Full on page 4 Using DriveExecutive on page 5 IMPORTANT If you re using DriveExplorer Life/Full with the 1203-USB converter, you need to update the converter firmware to FRN or higher.

2 Using the External LCD HIM (22-HIM-**) Step Key(s) Example Display 1. Power up the drive. Then plug the HIM into the drive. The Parameters menu for the drive is displayed. Parameters Groups Linear List Changed Params 2. Press Sel key until the Diagnostics menu is displayed. Sel DIAG PARAM DSEL MEM SEL Diagnostics Faults Device Status Device Version 3. Press Down Arrow to scroll to Device Version, and then press Enter. and DIAG PARAM DSEL MEM SEL Diagnostics Faults Device Status Device Version The present firmware version of the drive is shown on the Firmware line. DIAG PARAM DSEL MEM SEL Device Version PowerFlex 400 3P 230V 10HP Series: A Firmware: Using Connected Components Workbench Software 1. Launch the Connected Components Workbench software. 2. Open the project for your PowerFlex 400 drive. 3. On the main screen, click the Connect button to go online. 4. The firmware revision is displayed on the screen as shown below. Firmware revision 2 Rockwell Automation Publication 22C-RN001B-EN-E - August 2014

3 Using Logix Designer Software 1. Launch the Logix Designer software. 2. Open the project for your PowerFlex 400 drive. 3. On the main screen, click the Menu icon and select Go Online. 4. Right-click on the PowerFlex 400 drive and select Properties. 5. In the Module Properties window, select the Module Info tab to display the firmware revision. Firmware revision Rockwell Automation Publication 22C-RN001B-EN-E - August

4 Using DriveExplorer Lite/Full 1. Launch DriveExplorer and go online with the drive via the 1203-USB or 22-SCM-232 converter. 2. In the DriveExplorer tree view, click the PowerFlex 400 item as shown in Using Drive Explorer to determine current firmware revision on page Click the information icon to display the Properties screen of the drive. The Revision: field shows the present revision (for example, 5.001) of the PowerFlex 400 firmware. TIP When you click the PowerFlex 400 item in DriveExplorer Lite/Full version 5.01 or higher, the adapter firmware revision is also shown in the right pane of the DriveExplorer window. Using Drive Explorer to determine current firmware revision Step 3 Step 2 Step 4 4 Rockwell Automation Publication 22C-RN001B-EN-E - August 2014

5 Using DriveExecutive 1. Launch DriveExecutive and go online with the drive via the 1203-USB or the 22-SCM-232 converter. 2. In the DriveExecutive tree view, click the PowerFlex 400 item as shown in Using DriveExecutive to determine current firmware revision on page Click the information icon to display the Properties screen of the drive. The Revision: field shows the present revision (for example, 5.001) of the PowerFlex 400 firmware. Using DriveExecutive to determine current firmware revision Step 3 Step 2 Step 4 Rockwell Automation Publication 22C-RN001B-EN-E - August

6 Download Firmware Follow these steps to download firmware for your PowerFlex 400 drive. 1. Go to the Rockwell Automation Product Compatibility and Download Center at pcdc.page IMPORTANT You must sign in to the Rockwell Automation website before downloading a firmware revision. 2. Select the Get Downloads tab, then click the Find Product Downloads link. 3. Enter PowerFlex 400 into the Product Search field. The results appears in the box below. 6 Rockwell Automation Publication 22C-RN001B-EN-E - August 2014

7 4. Select the entry and the firmware revision, then click Downloads. 5. Click the Show Downloads icon, then click the firmware revision link to download it to your computer. 6. The downloaded file should contain the DSI Drive Flash Tool (DSI_DriveFlash.exe) and Flash Update File (*.mot). Firmware Upgrades Follow these steps to upgrade your firmware. What You Will Need A Serial Flash Firmware Kit (Catalog number AK-U9-FLSH1) A field flashable DSI drive. A PC computer with a free serial communications port and Internet connection. The DSI Drive Flash Tool (DSI_DriveFlash.exe) and Flash Update File (*.mot). See Download Firmware on page 6 on how to obtain the files. Connect Hardware 1. Remove all power to the drive including any externally supplied control power. L1 L2 L3 I ATTENTION: To avoid an electric shock hazard, verify that the voltage on the bus capacitors has discharged before performing any work on the drive. Measure the DC bus voltage at the +DC and DC terminals of the Power Terminal Block. The voltage must be zero. O Rockwell Automation Publication 22C-RN001B-EN-E - August

8 2. Disconnect all options connected to the DSI ports on the drive. DSI Port RS485 (DSI) Ports IMPORTANT Connected communication options can interfere with the flash process. 3. Connect the DSI cable and the Serial cable to the Flash Module. 4. Connect the 9-pin sub-miniature D-shell female connector of the Serial cable to a serial communications port on a PC computer. 8 Rockwell Automation Publication 22C-RN001B-EN-E - August 2014

9 5. Verify that the drive is Enabled. The drive is Enabled if: ENBL Enable Jumper is installed OR A valid input is supplied to I/O Terminal 01 Enable Jumper Installed on Control Board Input at I/O Terminal 01 (2 Wire Control Example Shown) ENBL RS485 (DSI) Stop-Run IMPORTANT The drive must be enabled during the flash process. 6. With all power removed from the drive, attach the 10-pin connector on the DSI cable to port J2 on the drive control board. J2 You are now ready to flash update the drive firmware. Flash the Drive 1. Obtain the latest DSI Drive Flash Tool (DSI_DriveFlash.exe) and Flash Update File (*.mot). See Download Firmware on page 6 on how to obtain the files. 2. Power up the drive and verify that the Green LED on the Flash Module lights. Rockwell Automation Publication 22C-RN001B-EN-E - August

10 3. Double-click DSI_DriveFlash.exe file to run the DSI Drive Flash Tool. Review and accept the license agreement. 4. From the DSI Drive Flash Tool s main window: Click Browse and select the desired flash update file. Select the correct serial communication port. Select the desired baud rate. The default baud rate is If problems occur during the flash routine, this rate can be reduced. 5. To begin the Flash Update routine, click the Flash Update button. 6. When programming is complete, exit the DSI Drive Flash Tool. Return Drive to Service 1. Remove power to the drive and wait for the Green LED on the Flash Module to go out. IMPORTANT If power is reapplied to the drive too quickly, the drive can remain locked in the flash state. If this occurs, remove power to the drive and wait three minutes before reapplying power. 2. Disconnect the DSI cable from port J2 on the drive control board. 3. Reconnect communication option if applicable. 4. Restore power to the drive. If the drive displays a F100 Parameter Checksum fault, cycle power to the drive. Repeat if the fault occurs a second time. 5. Reset parameters to factory defaults. Access parameter P041 [Reset to Defalts] and set to Access parameter d320 [Control SW Ver] and verify that the updated firmware version is installed. 7. Reprogram the drive for your application. 10 Rockwell Automation Publication 22C-RN001B-EN-E - August 2014

11 Enhancements There are no enhancements included in this firmware revision. New Parameters The following parameters are new in firmware revision To allow users more flexibility in configuring the sleep and wake operations, parameters T090 [Sleep Sel] and T091 [Wake Sel] have been added to the Terminal Block group. To use these parameters, set parameter T077 [Sleep-Wake Sel] to option 4 Ind Slp/Wake. To simplify using PID Setpoint with the sleep/wake functions without changing the values for Sleep Level and Wake Level, parameter A203 [Wake Deviation] has been added to the Advanced Program group. To allow users more flexibility in applying the values obtained from the analog inputs, parameters A204 [ACT1 Input], A205 [ACT2 Input], A206 [ACT1 Minimum], A207 [ACT1 Maximum], A208 [ACT2 Minimum], and A209 [ACT2 Maximum] have been added to the Advanced Program group. To allow preloading of the integral component on wake, parameter A210 [Wake PID Preload] has been added to the Advanced Program group. Parameter Updates The following parameters have been updated in firmware revision Option 24 Fault has been added to parameters T055 [Relay Out1 Sel], T060 [Relay Out2 Sel], T065 [Opto Out Sel], R221 [Relay Out3 Sel], R224 [Relay Out4 Sel], R227 [Relay Out5 Sel], R230 [Relay Out6 Sel], R233 [Relay Out7 Sel], and R236 [Relay Out8 Sel]. When this option is selected, the relay remains in the off state when power is applied to the drive and energizes when a fault occurs. This is inverted from Option 0, Ready/Fault. Option 4 Ind Slp/Wake has been added to parameter T077 [Sleep-Wake Sel] to enable the Sleep and Wake functions to work independently. Analog input settings have been added to parameters T082 [Analog Out1 Sel] and T085 [Analog Out2 Sel]. Setting Output Range Min. Output Value Max. Output Value = [Analog Output Hi] Filter DIP Switch AO1 Setting Related Parameter 24 AnlgIn V 0V = 0.0% 100.0% Setting Filter A 10V d AnlgIn ma 0 ma = 0.0% 100.0% Setting Filter A 20 ma d AnlgIn ma 4 ma = 0.0% 100.0% Setting Filter A 20 ma d AnlgIn V 0V = 0.0% 100.0% Setting Filter A 10V d AnlgIn ma 0 ma = 0.0% 100.0% Setting Filter A 20 ma d AnlgIn ma 4 ma = 0.0% 100.0% Setting Filter A 20 ma d306 Rockwell Automation Publication 22C-RN001B-EN-E - August

12 Options have been added to parameter A153 [PID Feedback Sel]. These options allow different applications of the new actual (ACT) 1 and 2 parameters. Option Description 3 ACT1 - ACT2 ACT1 minus ACT2 4 ACT1 + ACT2 ACT1 plus ACT2 5 ACT1 * ACT2 ACT1 multiplied by ACT2 6 ACT1 / ACT2 ACT1 divided by ACT2 7 Min A1, A2 The smaller of ACT1 or ACT2 is used as the feedback signal. 8 Max A1, A2 The larger of ACT1 or ACT2 is used as the feedback signal. The values for parameter d328 [PID Fdbk Display] have been updated: Minimum value updated from 0.0% to %. Maximum value updated from 120.0% to 200.0%. Corrected Anomalies Known Anomalies There are no anomalies corrected in this firmware revision. There are no known anomalies present in this firmware revision. 12 Rockwell Automation Publication 22C-RN001B-EN-E - August 2014

13 Notes: Rockwell Automation Publication 22C-RN001B-EN-E - August

14 Rockwell Automation Support Rockwell Automation provides technical information on the Web to assist you in using its products. At you can find technical manuals, a knowledge base of FAQs, technical and application notes, sample code and links to software service packs, and a MySupport feature that you can customize to make the best use of these tools. For an additional level of technical phone support for installation, configuration, and troubleshooting, we offer TechConnect support programs. For more information, contact your local distributor or Rockwell Automation representative, or visit Installation Assistance If you experience a problem within the first 24 hours of installation, review the information that is contained in this manual. You can contact Customer Support for initial help in getting your product up and running. United States or Canada Outside United States or Canada Use the Worldwide Locator at or contact your local Rockwell Automation representative. New Product Statisfaction Return Rockwell Automation tests all of its products to ensure that they are fully operational when shipped from the manufacturing facility. However, if your product is not functioning and needs to be returned, follow these procedures. United States Outside United States Contact your distributor. You must provide a Customer Support case number (call the phone number above to obtain one) to your distributor to complete the return process. Please contact your local Rockwell Automation representative for the return procedure. Documentation Feedback Your comments will help us serve your documentation needs better. If you have any suggestions on how to improve this document, complete this form, publication RA-DU002, available at U.S. Allen-Bradley Drives Technical Support - Tel: (1) , Fax: (1) , support@drives.ra.rockwell.com, Online: Allen-Bradley, Rockwell Software, Rockwell Automation, PowerFlex, Connected Components Workbench, Studio 5000, DriveTools SP, and TechConnect are trademarks of Rockwell Automation, Inc. Trademarks not belonging to Rockwell Automation are property of their respective companies. Rockwell Otomasyon Ticaret A.Ş., Kar Plaza İş Merkezi E Blok Kat: İçerenköy, İstanbul, Tel: +90 (216) lautomation.com Power, Control and Information Solutions Headquarters Americas: Rockwell Automation, 1201 South Second Street, Milwaukee, WI USA, Tel: (1) , Fax: (1) Europe/Middle East/Africa: Rockwell Automation NV, Pegasus Park, De Kleetlaan 12a, 1831 Diegem, Belgium, Tel: (32) , Fax: (32) Asia Pacific: Rockwell Automation, Level 14, Core F, Cyberport 3, 100 Cyberport Road, Hong Kong, Tel: (852) , Fax: (852) Publication 22C-RN001B-EN-E - August 2014 Supersedes Publication 22C-RN001A-EN-E - August 2010 Copyright 2014 Rockwell Automation, Inc. All rights reserved.