Working around ERR7026 according to application needs
|
|
|
- Erik Osborne Young
- 5 years ago
- Views:
Transcription
1 Freescale Semiconductor Document Number: EB795 Engineering Bulletin Rev. 0, 08/2013 Working around ERR7026 according to application needs by: Automotive and Industrial Solutions Group 1 Introduction This document aims to describe Errata 7026 which affect the MPC564xS devices and how to safely handle it. Contents 1 Introduction Errata Description Workaround options Increase the time the MCU remains in Standby Use a pull down resistor on VDD Summary comparison of workarounds Pull down resistor simulation... 5 Freescale Semiconductor, Inc., All rights reserved.
2 2 Errata Description Repetitively cycling the flash with Standby mode may disturb flash bits, causing them to flip from a 1 (erased state) to a 0 (programmed state) when switching from Standby back to Run mode with VDD12 at approximately 100 mv. 3 Workaround options When exiting Standby mode, ensure that the VDD12 pins are allowed to fully discharge to VSS (below 60 mv) before entering a Run mode. There are two recommended ways of ensuring that VDD12 is fully discharged: Increase the time the MCU remains in Standby Use a pull down resistor on VDD12 These options are recommendations or guidelines that each customer needs to analyze and adjust to their specific application. In the following sections these two options are described in more detail. 3.1 Increase the time the MCU remains in Standby The discharge time for the VDD12 capacitor array depends on both the VDD12 capacitance value and the Standby current. Standby current depends on the application conditions (such as Standby mode, SXOSC and RTC configurations) and could range between tens to hundreds of µa as the following table illustrates: Table 1. Low power mode current consumption Parameter Conditions Value Unit Typ Max STANDBY2 mode current (64K SRAM on) STANDBY1 mode current (8K SRAM on) SXOSC (32 khz) ON and RTC running SXOSC (32 khz) and RTC OFF SXOSC (32 khz) ON and RTC running SXOSC (32 khz) and RTC OFF µa µa Freescale Semiconductor 2
3 Please refer to the MPC5645S datasheet for the complete table. It is recommended to evaluate the characteristics of each application and determine if increasing the Standby time ensures VDD12 to be below 60 mv before exiting the Standby mode. The amount of time needed to discharge VDD12 will depend on the application hardware and capacitance assigned to the VDD12 pins. The following table illustrates the time needed to discharge VDD12 pins: Table 2. Increasing the time between wake up and sleep modes Short wake up time MCU goes to standby and wakes up after ms. VDD12 voltage drops to 120 mv. This application could eventually experience errata Longer wake up time MCU goes to standby and wakes up after 123 ms. VDD12 voltage has dropped to 50 mv. This application is safe. Freescale Semiconductor 3
4 3.2 Use a pull down resistor on VDD12 Including an additional pull-down resistor on VDD12 will shorten the VDD12 capacitive array discharge time. Additional current demand for VDD12 needs to be considered during RUN and STOP modes. The following table illustrates the voltage on VDD12 pin with different pull down resistors: Table 3. Adding a resistor to VDD12 Situation description This application wakes up after ms of standby mode. VDD12 pins are allowed to drop only to 120 mv. This application may eventually experience errata Allowing more discharge time or adding a pull down resistor is recommended. Scope image of VDD12 voltage A 5.4k pull down resistor is added at VDD12. Wake up time was not changed. VDD12 voltage drops to 60 mv before next wake up. This application could eventually experience errata Lowering the resistance to ground is recommended to allow VDD21 voltage to drop below 60 mv before next wake up. A 1 k pull down resistor is added at pin VDD12. VDD12 voltage drops well below 60 mv before next wake up. This application is safe from errata Freescale Semiconductor
5 3.3 Summary comparison of workarounds The following table provides a summary and comparison of both proposed workarounds as a reference to the user: Table 4. Comparison of ERR7026 workarounds Description Increase the time the MCU remains in standby Application does not wake up from standby until a time has passed that assures VDD12 is discharged. Use a pull down resistor on VDD12 An external pull down resistor is used to lower the discharge time of VDD12. Current consumption Not affected Increased by current consumed by resistor. Application response time to an event from standby Response to an event may be delayed to allow VDD12 to discharge. Not affected External components Not affected A single external resistor is needed. NOTE All measurements were made on the MPC5645S board, which has four 10 F capacitors and four 0.1 F capacitors to ground, and a 10 k pull down resistor on the VDD12 pins. 4 Pull down resistor simulation The following image illustrates a simulation comparing the different pull down resistor options and their resulting discharge times for VDD12: Figure 1. VDD12 Discharge resulting from different pull down resistor configurations Freescale Semiconductor 5
6 Information in this document is provided solely to enable system and software implementers to use Freescale products. There are no express or implied copyright licenses granted hereunder to design or fabricate any integrated circuits based on the information in this document. How to Reach Us: Home Page: freescale.com Web Support: freescale.com/support Freescale reserves the right to make changes without further notice to any products herein. Freescale makes no warranty, representation, or guarantee regarding the suitability of its products for any particular purpose, nor does Freescale assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. Typical parameters that may be provided in Freescale data sheets and/or specifications can and do vary in different applications, and actual performance may vary over time. All operating parameters, including typicals, must be validated for each customer application by customer s technical experts. Freescale does not convey any license under its patent rights nor the rights of others. Freescale sells products pursuant to standard terms and conditions of sale, which can be found at the following address: freescale.com/salestermsandconditions. Freescale, the Freescale logo, CodeWarrior, ColdFire, C-Ware and Qorivva are trademarks of Freescale Semiconductor, Inc., Reg. U.S. Pat. & Tm. Off. SafeAssure, Vybrid are trademarks of Freescale Semiconductor, Inc. All other product or service names are the property of their respective owners. Freescale Semiconductor, Inc All rights reserved. Document Number: EB791 Rev. 0 04/2013
Adding a run control interface into an existing CodeWarrior for MCU v10.x project
Freescale Semiconductor Document Number:AN4902 Application Note Rev 03/2014 Adding a run control interface into an existing CodeWarrior for MCU v10.x project 1 Introduction There are two ways to add a
i.mx 6Solo/6DualLite Product Lifetime Usage Estimates
Freescale Semiconductor, Inc. Application Note Document Number: AN4725 Rev. 2, 02/2015 i.mx 6Solo/6DualLite Product Lifetime Usage Estimates This document describes the estimated product lifetimes for
FRDM-K64F Board Errata
Freescale Semiconductor, Inc. Document Number: FRDMK64F_ERRATA Board Errata Rev. 2.0, 06/2014 FRDM-K64F Board Errata by: Freescale Semiconductor, Inc. 2014 Freescale Semiconductor, Inc. 1 Errata Title:
DDR Validation Tool Getting Started Guide
DDR Validation Tool Getting Started Guide Document Number: QCVSDDRVGETSTARTUG Rev 4.1, 10/2014 2 Freescale Semiconductor, Inc. Contents Section number Title Page Chapter 1 Getting Started with DDR Validation
General C Functions for the etpu Covers the MCF523x, MPC5500, MPC5600, MPC5700, MPX40 and all etpu-equipped Devices
Freescale Semiconductor Document Number: AN2864 Application Note Rev. 2, 09/2015 General C Functions for the etpu Covers the MCF523x, MPC5500, MPC5600, MPC5700, MPX40 and all etpu-equipped Devices by:
Mask Set Errata for Mask 2N27B
Freescale Semiconductor COLDFIREPLUS_2N27B Mask Set Errata Rev 29 JUL 2013 Mask Set Errata for Mask 2N27B Introduction This report applies to mask 2N27B for these products: COLDFIREPLUS Errata ID Errata
How to setup pre-build steps in CodeWarrior for Microcontrollers v10.x
Freescale Semiconductor Application Note Document Number: AN4910 How to setup pre-build steps in CodeWarrior for Microcontrollers v10.x 1. Introduction This document outlines the steps for setting up userdefined
Flash Core Voltage Supply Requirements and Considerations
Freescale Semiconductor Application Note Document Number: AN4758 Rev. 1, 6/2013 Flash Core Voltage Supply Requirements and Considerations by: David Paterson 1 Introduction The voltage supply for Freescale
Processor Expert Software for i.mx Processors Version 1.0
Release Notes Processor Expert Software for i.mx Processors Version 1.0 1 Overview Processor Expert Software for i.mx processors is a suite of configuration tools for i.mx family processors. This file
i.mxrt1050 Product Lifetime Usage Estimates
NXP Semiconductors Document Number: AN12170 Application Note Rev. 0, 04/2018 i.mxrt1050 Product Lifetime Usage Estimates 1. Introduction This document describes the estimated product lifetimes for the
P1010RDB-PB Quick Start Guide
Freescale Semiconductor P1010RDB-PB Quick Start Guide Document Number: P1010RDBPBQS Rev. 0, 10/2013 P1010RDB-PB Quick Start Guide 1 Introduction to P1010RDB-PB This quick start guide applies to boards
Freescale MKW40Z IEEE Software Quick Start Guide
Freescale Semiconductor, Inc. Document Number: MKW40Z802154SW523QSG User's Guide Rev. 0, 09/2015 Freescale MKW40Z IEEE 802.15.4 Software Quick Start Guide This document is a brief presentation of the Freescale
Three-Phase Power Meter Hardware Design Reference Manual
Freescale Semiconductor, Inc. Document Number: DRM146 Design Reference Manual Rev. 0, 03/2014 Three-Phase Power Meter Hardware Design Reference Manual by: Albert Chen and Shawn Shi 1 Overview Freescale
KIT33972AEWEVBE Evaluation Board
Freescale Semiconductor, Inc. User s Guide Document Number: KT33972UG Rev. 1.0, 7/2013 KIT33972AEWEVBE Evaluation Board Featuring the MC33972A Multiple Switch Detection Interface IC Contents Figure 1.
New VLE Instructions for Improving Interrupt Handler Efficiency Robert Moran Applications Engineer Microcontroller Solutions Group
Freescale Semiconductor Engineering Bulletin Document Number: EB696 Rev. 0, 07/2008 New VLE Instructions for Improving Interrupt Handler Efficiency by: Robert Moran Applications Engineer Microcontroller
MMPF0100 Errata for Mask 1N47F and 1N18J
Freescale Semiconductor Errata (or Chip Errata) Document Number: MMER Rev. 5.0, 4/2014 MM Errata for Mask 1N47F and 1N18J Introduction Device Revision Identification This errata document applies to the
Watt Saver Software Component (WSC)
Freescale Semiconductor Document Number:WSSCUG User Guide Rev 1, 10/2013 Watt Saver Software Component (WSC) 1 Introduction This document describes the basic steps for getting started with the Watt Saver
S12VR Hardware Design. Guidelines. 1 Introduction. 2 Hardware Design. Guidelines. 2.1 Voltage regulator. Freescale Semiconductor
Freescale Semiconductor Document Number: AN4643 Application Note Rev 1, 10/2013 S12VR Hardware Design Guidelines by: Carlos Aceff 1 Introduction This document lists the required external components and
Component Development Environment Getting Started Guide
Component Development Environment Getting Started Guide Document Number: CDEGS Rev 02/2014 2 Freescale Semiconductor, Inc. Contents Section number Title Page Chapter 1 Introduction 1.1 Overview...5 1.2
KIT34901EFEVB Evaluation Board
Freescale Semiconductor, Inc. User s Guide Document Number: KT34901UG Rev. 1.0, 2/2014 KIT34901EFEVB Evaluation Board Featuring the MC34901 High Speed CAN Transceiver Contents Figure 1. KIT34901EFEVB Evaluation
Freedom FRDM-MC-LVBLDC Development Platform User s Guide
Freescale Semiconductor, Inc. Document Number: FRDMLVBLDCUG User's Guide 0, 02/2016 Freedom FRDM-MC-LVBLDC Development Platform User s Guide 1. Introduction The Freedom development platform is a set of
Single Chip Module (SCM) Package-on- Package (PoP) Assembly Guide
Freescale Semiconductor, Inc. Document Number: AN5247 Application Notes Rev. 0, 01/2016 Single Chip Module (SCM) Package-on- Package (PoP) Assembly Guide 1. Introduction Freescale Single Chip Modules (SCM)
Integrate TWR-EPD Software with MQX RTOS Based on the TWR-K21F120M Platform
Freescale Semiconductor, Inc. Application Note Document Number: AN5069 Rev. 0, 01/2015 Integrate TWR-EPD Software with MQX RTOS Based on the TWR-K21F120M Platform 1 Introduction This application note describes
i.mx 6 Android JB 4.3_1.1.1 Patch Release Notes
Freescale Semiconductor, Inc. Document Number: IMX6JBPATCHRN Release Notes Rev. JB 4.3_1.1.1, 10/2014 i.mx 6 Android JB 4.3_1.1.1 Patch Release Notes 1 Overview This patch release is based on the i.mx
Getting Started with Freescale MQX RTOS for Kinetis SDK and MDK-ARM Keil
Freescale Semiconductor, Inc. Document Number: KSDKGSKEILUG User s Guide Rev. 1, 04/2015 Getting Started with Freescale MQX RTOS for Kinetis SDK and MDK-ARM Keil µvision5 1 Read Me First This document
Quick Start Guide for FRDM-FXS-MULTI-B
Quick Start Guide for FRDM-FXS-MULTI-B Contents: Quick Start Package Overview Get to Know the FRDM-FXS-MULTI-B Getting Started Out of the Box Explore Further freescale.com/frdm-multi-b External Use FRDMFXSMULTIBQSG
Building U-Boot in CodeWarrior ARMv8
NXP Semiconductors Document Number: AN5347 Application Note Rev. 0, 10/2016 Building U-Boot in CodeWarrior ARMv8 1 Introduction This application note defines guidelines for configuring CodeWarrior for
MM912_634, Silicon Analog Mask (M91W) / Digital Mask (N53A) Errata
Freescale Semiconductor, Inc. Chip Errata Document Number: MM912_634ER Rev. 7.0, 4/2015 MM912_634, Silicon Analog Mask (M91W) / Digital Mask (N53A) Errata This errata document applies to the MM912_634
i.mx 6ULL Product Usage Lifetime Estimates
NXP Semiconductors Document Number: AN5337 Application Note Rev. 1, 03/2017 i.mx 6ULL Product Usage Lifetime Estimates 1. Introduction This document describes the estimated product lifetimes for the i.mx
Mask Set Errata for Mask 3N86B
Freescale Semiconductor KINETIS_50MHZ_3N86B Mask Set Errata Rev 08 AUG 2013 Mask Set Errata for Mask 3N86B Introduction This report applies to mask 3N86B for these products: KINETIS_50MHZ Errata ID Errata
HVP-MC56F82748 User s Guide
Freescale Semiconductor, Inc. User s Guide Document Number: HVPMC56F82748UG Rev. 0, 12/2014 HVP-MC56F82748 User s Guide by: Ivan Lovas 1 High voltage controller cards overview This document supports the
Generating a Quick and Controlled Waveform With the DAC
Freescale Semiconductor Document Number: AN4978 Application Note Rev 0, 08/2014 Generating a Quick and Controlled Waveform With the DAC by: Arpita Agarwal 1 Overview This application note describes how
Quick Start Guide for the Freescale Freedom Development Platform FRDM-KL43Z
Quick Start Guide for the Freescale Freedom Development Platform FRDM-KL43Z External Use Contents ts Quick Start Package Overview GettoKnowtheFRDMKL43Z to the FRDM-KL43Z Getting Started Out of the Box
Quick Start Guide for FRDM-KL05Z
Quick Start Guide for FRDM-KL05Z Contents: Quick Start Package Overview Get to Know the FRDM-KL05Z Getting Started Out of the Box Introduction to OpenSDA Explore Further www.freescale.com/frdm-kl05z 1
CodeWarrior Development Studio Processor Expert RTOS Adapter User Guide
CodeWarrior Development Studio Processor Expert RTOS Adapter User Guide Document Number: CWPEXRTUG Rev 10.6, 02/2014 2 Freescale Semiconductor, Inc. Contents Section number Title Page Chapter 1 Introduction
HVP-KV10Z32 User s Guide
Freescale Semiconductor, Inc. User s Guide Document Number: HVPKV10Z32UG Rev. 0, 12/2014 HVP-KV10Z32 User s Guide by: Ivan Lovas 1 High voltage controller card HVP-KV10Z32 This document supports the HVP-MC3PH
PMSM Field-Oriented Control Using MC56F84789 DSC With Encoders Demo Guide
Freescale Semiconductor Document Number: PMSMUG User Guide Rev. 0, 06/2013 PMSM Field-Oriented Control Using MC56F84789 DSC With Encoders Demo Guide by: Pavel Rech 1 Introduction The application described
Using DMA for Pulse Counting on S32K
Freescale Semiconductor, Inc. Document Number: AN5258 Application Note Rev. 0, 02/2016 Using DMA for Pulse Counting on S32K 1. Introduction This application note describes pulse counting on the S32K product
i.mx 7 Dual/Solo Product Lifetime Usage
NXP Semiconductors Document Number: AN5334 Application Note Rev. 1, 05/2017 i.mx 7 Dual/Solo Product Lifetime Usage 1. Introduction This document describes the estimated product lifetimes for the i.mx
i.mx 6UltraLite Product Usage Lifetime Estimates
NXP Semiconductors Document Number: AN5198 Application Notes Rev. 2, 08/2016 i.mx 6UltraLite Product Usage Lifetime Estimates 1. Introduction This document describes the estimated product lifetimes for
Getting Started with Freescale MQX RTOS for Kinetis SDK and Kinetis Design Studio IDE
Freescale Semiconductor, Inc. Document Number: KSDKGSKDSUG User s Guide Rev. 1, 04/2015 Getting Started with Freescale MQX RTOS for Kinetis SDK and Kinetis Design Studio IDE 1 Overview This section describes
Intelligent Sensing Framework 2.1 for Kinetis Errata Sheet
Document Number: ISF2P1_KINETIS_ER ERRATA SHEET Rev. 1, 4/2015 Intelligent Sensing Framework 2.1 for Kinetis Errata Sheet The following errata sheet covers changes to the Freescale Intelligent Sensing
Kinetis Updater User's Guide
Freescale Semiconductor Document Number: KUPDTRUG User's Guide Rev. 1, 07/2015 Kinetis Updater User's Guide 1 Introduction The Kinetis Updater is a Windows OS application used to write user application
MMA845x Driver: Quick Start Guide
Freescale Semiconductor Document Number: AN4475 Application Note Rev 0, 07/2012 MMA845x Driver: Quick Start Guide by: Laura Salhuana 1 Introduction This quick start guide demonstrates how to load the MMA845x
Using an External GCC Toolchain with CodeWarrior for Power Architecture
Freescale Semiconductor Application Note Document Number: AN5277 Using an External GCC Toolchain with CodeWarrior for Power Architecture 1. Introduction This document explains how to use an external GNU
Configuring DDR in U-Boot using QCVS
NXP Semiconductors Application Note Document Number: AN5279 Configuring DDR in U-Boot using QCVS 1. Introduction This document describes how to configure the double data rate (DDR) memory in U-Boot, running
HVP-KV31F120M User s Guide
Freescale Semiconductor, Inc. User s Guide Document Number: HVPKV31F120MUG Rev. 0, 12/2014 HVP-KV31F120M User s Guide by: Ivan Lovas 1 High voltage controller card HVP-KV31F120M This document supports
MQX RTOS Release Notes for Kinetis SDK v1.2.0 for KL33Z64 for FRDM-KL43Z Freescale Freedom Development Platform
Freescale Semiconductor Document Number: MQXKSDK120KL33RN Release Notes Rev. 0, 4/2015 MQX RTOS Release Notes for Kinetis SDK v1.2.0 for KL33Z64 for FRDM-KL43Z Freescale Freedom Development Platform 1
Table of Contents 1 Typical Applications General Description Block Diagram Pinout System Connections Typical A
Data Sheet: Product Preview Rev 0.3, 3/2014 Xtrinsic 3-Axis Digital Angular Rate Gyroscope is a small, low-power, yaw, pitch, and roll angular rate gyroscope. The full-scale range is adjustable from ±250
OpenSDA on TWR-KW2x. User s Guide Rev 1.1
OpenSDA on TWR-KW2x User s Guide 2013 Rev 1.1 Freescale, Inc. TKW2x_OSDAUG Table of Contents 1 Overview...3 1.1 OpenSDA Hardware...4 1.2 OpenSDA Software...4 1.2.1 MSD Bootloader...4 1.2.2 P&E Debug Application...5
KIT33887EKEVB Evaluation Board
Freescale Semiconductor, Inc User s Guide Document Number: KT33887UG Rev 20, 4/2013 KIT33887EKEVB Evaluation Board Featuring the MC33887EK 50 A H-Bridge IC Contents Figure 1 KIT33887EKEVB Evaluation Board
TWR-LS1021A Getting Started
Freescale Semiconductor Getting Started Document Number: TWR-LS1021AGS Rev. 0, 09/2014 TWR-LS1021A Getting Started 1 Introduction This document explains how to connect the QorIQ LS1021A Tower System Module
TWR-KV10Z32 Sample Code Guide for CodeWarrior Board configuration, software, and development tools
Freescale Semiconductor User s Guide Doc Number: TWRKV10Z32CWUG Rev. 0.1, 01/2014 TWR-KV10Z32 Sample Code Guide for CodeWarrior Board configuration, software, and development tools by Freescale Semiconductor,
Getting Started with Freescale MQX RTOS for Kinetis SDK and ARM GCC
Freescale Semiconductor, Inc. Document Number: KSDKGSARMGCCUG User s Guide Rev. 1, 04/2015 Getting Started with Freescale MQX RTOS for Kinetis SDK and ARM GCC 1 Overview This section describes the steps
High Volume Pressure Sensor for Disposable Applications
Freescale Semiconductor Data Sheet: Technical Data Pressure Rev 9, 10/2012 High Volume Pressure Sensor for Disposable Applications Freescale Semiconductor has developed a low cost, high volume, miniature
MC34708, Silicon Errata
Freescale Semiconductor Errata Document : Rev. 9.0, 11/2013 MC34708, Silicon Errata Introduction Device Revision Identification This errata document applies to the following devices: Table 1. Silicon Revision
MPXHZ6130A, 15 to 130 kpa, Absolute, Integrated Pressure Sensor
Freescale Semiconductor Document Number: Data Sheet: Technical Data Rev. 1.2, 06/2015, 15 to 130 kpa, Absolute, Integrated Pressure Sensor The series sensor integrates on-chip, bipolar op amp circuitry
Understanding S08P Internal Clock Source
Freescale Semiconductor Application Note Document Number: AN4763 Rev. 0, 8/2013 Understanding S08P Internal Clock Source By: William Jiang 1 Introduction The S08P family integrates an internal clock source
CodeWarrior Development Studio for StarCore 3900FP DSP v SP3 Release Notes
Freescale Semiconductor Document Number: CW_SC_3900FP_v10.8.3 SP3 Release Notes Rev. 1.0, 11/2015 CodeWarrior Development Studio for StarCore 3900FP DSP v10.8.3 SP3 Release Notes Release Description ServicePack3
Freescale Semiconductor Data Sheet: Technical Data
Freescale Semiconductor Data Sheet: Technical Data High Temperature Accuracy Integrated Silicon Pressure Sensor for Measuring Absolute Pressure, On-Chip Signal Conditioned, Temperature Compensated and
Quick Start Guide for FRDM-KL46Z Rev 1
www.freescale.com/frdm-kl46z These documents are available as part of the Quick Start Package: Name Type Description Quick Start Guide PDF This document OpenSDA Applications Folder OpenSDA Applications
MQX RTOS Release Notes for Kinetis SDK FRDM- KV10Z Freescale Freedom Development Platform
Freescale Semiconductor Document Number: MQXKSDK120KV10RN Release Notes Rev. 0, MQX RTOS Release Notes for Kinetis SDK 1.2.0 FRDM- KV10Z Freescale Freedom Development Platform 1 Overview These are the
Collecting Linux Trace without using CodeWarrior
Freescale Semiconductor Application Note Document Number: AN5001 Collecting Linux Trace without using CodeWarrior 1. Introduction This document guides you how to collect Linux trace directly from QDS or
Heterojunction Bipolar Transistor Technology (InGaP HBT) High Efficiency/Linearity Amplifier
Freescale Semiconductor Technical Data Heterojunction Bipolar Transistor Technology (InGaP HBT) High Efficiency/Linearity Amplifier The MMA20312B is a 2--stage high efficiency, Class AB InGaP HBT amplifier
Qorivva MPC5744P Evaluation Board 144LQFP Expansion Board User s Guide Barbara Johnson Applications Engineering
Freescale Semiconductor User s Guide Document Number: MPC5744PEVB144UG Rev. 1, 11/2012 Qorivva MPC5744P Evaluation Board 144LQFP Expansion Board User s Guide by: Barbara Johnson Applications Engineering
Installing Service Pack Updater Archive for CodeWarrior Tools (Windows and Linux) Quick Start
Installing Service Pack Updater Archive for CodeWarrior Tools (Windows and Linux) Quick Start SYSTEM REQUIREMENTS Hardware Operating System Disk Space Windows OS: PC with 1 GHz Intel Pentium compatible
Mask Set Errata for Mask 0N22G
Freescale Semiconductor MSE9S12ZVL_0N22G Mask Set Errata Rev 29 SEP 2014 Mask Set Errata for Mask 0N22G This report applies to mask 0N22G for these products: MSE9S12ZVL ID before 15 MAY 2008 ID from 15
Kinetis USB-KW41Z Wireless Protocol Sniffer Quick Start Guide
NXP Semiconductors Document Number: MKW41ZSNIFFERQSG User's Guide Rev. 2, 09/2016 Kinetis USB-KW41Z Wireless Protocol Sniffer Quick Start Guide This document describes the usage of the USB- KW41Z evaluation
SPI topics: watchdog, serial output and parity check
NXP Semiconductors Application Note Document Number: AN5106 Rev. 1.0, 7/2016 SPI topics: watchdog, serial output and parity check for the dual SOIC 24 V high-side switch family 1 Introduction This application
TWR-KV10Z32 Sample Code Guide for IAR Board configuration, software, and development tools
Freescale Semiconductor User s Guide Doc Number: TWRKV10Z32IARUG Rev. 0.1, 01/2014 TWR-KV10Z32 Sample Code Guide for IAR Board configuration, software, and development tools by Freescale Semiconductor,
Quick Start Guide for FRDM-KL46Z Rev 1
www.freescale.com/frdm-kl46z These documents are available as part of the Quick Start Package: Name Type Description Quick Start Guide PDF This document OpenSDA Applications Folder OpenSDA Applications
Getting Started with the MCU Flashloader
NXP Semiconductors Document Number: MBOOTFLASHGS User's Guide Rev 3, 05/2018 Getting Started with the MCU Flashloader Contents Contents Chapter 1 Introduction...3 Chapter 2 Overview...4 2.1 MCU flashloader...4
Emulating I2C Bus Master by using FlexIO
Freescale Semiconductor, Inc. Document Number: AN5133 Application Notes Rev. 0, 06/2015 Emulating I2C Bus Master by using FlexIO 1. Introduction This application note lists the steps to use the FlexIO
MC56F825x/MC56F824x (2M53V) Chip Errata
Freescale Semiconductor MC56F825XE_2M53V Chip Errata Rev. 1, 05/2012 MC56F825x/MC56F824x (2M53V) Chip Errata The following errata items apply to devices of the maskset 2M53V. 2012 Freescale Semiconductor,
i.mxrt1060 Product Lifetime Usage Estimates
NXP Semiconductors Document Number: AN12253 Application Notes Rev. 0, 09/2018 i.mxrt1060 Product Lifetime Usage Estimates Introduction This document describes the estimated product lifetimes for the i.mx
Using VRC_CTL to Control an External VDD_LV Supply on the MPC5748G
NXP Semiconductors Document Number: AN5290 Application Note Rev. 0, 06/2016 Using VRC_CTL to Control an External VDD_LV Supply on the MPC5748G by: Alasdair Robertson 1 Introduction The MPC5748G MCU is
MP3V5050V, -50 to 0 kpa, Gauge Pressure Sensor
Freescale Semiconductor Document Number: Data Sheet: Technical Data Rev. 3.0, 09/2015, -50 to 0 kpa, Gauge Pressure Sensor The piezoresistive transducer is a state-of-the-art, monolithic, signal conditioned,
Emulating Dual SPI Using FlexIO
Freescale Semiconductor, Inc. Document Number: AN5242 Application Note Rev. 0, 01/2016 Emulating Dual SPI Using FlexIO 1. Introduction This application note discusses one example of how to use FlexIO module
TWR-LS1021A Getting Started
Freescale Semiconductor Getting Started Document Number: TWR-LS1021AGS Rev. 3, 10/2015 TWR-LS1021A Getting Started 1 Introduction This document describes how to connect the QorIQ LS1021A Tower System Module
Using the MPC5777M MCAN Module to Exchange CAN FD Messages
Freescale Semiconductor Document Number: AN5045 Application Note Rev. 0, 11/2014 Using the MPC5777M MCAN Module to Exchange CAN FD Messages by: Graham Rice 1 Introduction A CAN network (Controller Area
QCVS Frame Distributor Wizard User Guide
QCVS Frame Distributor Wizard User Guide Document Number: QCVSFDWUG Rev. 4.3, 07/2015 2 Freescale Semiconductor, Inc. Contents Section number Title Page Chapter 1 Frame Distributor Wizard 1.1 Introduction...5
MPXH6300A, 20 to 300 kpa, Absolute, Integrated, Pressure Sensor
Freescale Semiconductor Document Number: Data Sheet: Technical Data Rev. 6.0, 09/2015, 20 to 300 kpa, Absolute, Integrated, Pressure Sensor Freescale's series sensor integrates on-chip, bipolar op amp
Getting Started with MQX RTOS for Kinetis SDK
Freescale Semiconductor Document Number: MQXKSDKGSUG User's Guide Rev. 1, 04/2015 Getting Started with MQX RTOS for Kinetis SDK 1 Introduction This document describes the steps required to configure supported
Kinetis Bootloader to Update Multiple Devices in a Field Bus Network
Freescale Semiconductor, Inc. Document Number: AN5204 Application Note Rev. 0, 01/2016 Kinetis Bootloader to Update Multiple Devices in a Field Bus Network 1. Introduction This application note describes
KIT09XS3400EVBE Evaluation Board User Guide Featuring the MC09XS3400
Freescale Semiconductor User s Guide Document Number: KT09XS00UG Rev..0, 8/0 KIT09XS00EVBE Evaluation Board User Guide Featuring the MC09XS00 Figure. KIT09XS00EVBE Evaluation Board Table of Contents Kit
AIOP Task Aware Debug
Freescale Semiconductor Document Number: AN5044 Application Note Rev. 05/2015 AIOP Task Aware Debug 1 Introduction This document describes the how to debug the AIOP tasks. It also describes the AIOP task
CodeWarrior U-Boot Debugging
Freescale Semiconductor Application Note Document Number: AN4876 CodeWarrior U-Boot Debugging 1. Introduction This document describes the steps required for U-Boot debugging using the CodeWarrior IDE.
MAG3110 Frequently Asked Questions
Freescale Semiconductor Frequently Asked Questions Document Number: Rev 1, 05/2012 MAG3110 Frequently Asked Questions Applications Collateral for the MAG3110 to Aid Customer Questions Data Sheet, Fact
FRDM-KL03Z User s Guide
Freescale Semiconductor User s Guide Document Number: FRDMKL03ZUG Rev. 0, 7/2014 FRDM-KL03Z User s Guide 1 Overview The Freescale Freedom development platform is an evaluation and development tool ideal
FRDM-KE04Z User s Guide User Guide
Freescale Semiconductor Document Number: FRDMKE04ZUM User's Guide Rev 0, 02/2014 FRDM-KE04Z User s Guide User Guide by: Wang Peng 1 Overview The Freescale Freedom development platform is an ideal evaluation
KITUSBSPIEVME USB-to-SPI Interface Board Featuring the MC68HC908JW32
Freescale Semiconductor, Inc. User s Guide Document Number: KTUSBSPIEVMEUG Rev. 4.0, 4/2013 KITUSBSPIEVME USB-to-SPI Interface Board Featuring the MC68HC908JW32 Figure 1. KITUSBSPIEVME Board Table of Contents
KITPF0100SKTEVBE Programming Socket
Freescale Semiconductor, Inc. User s Guide Document Number: KTPFSKTUG Rev.., 6/3 KITPFSKTEVBE Programming Socket Configures PF Family Devices Figure. PF Programming Socket (KITPFSKTEVBE) Table of Contents
WCT1011A/WCT1013A Automotive MP-A9 V4.0 Run-Time Debugging
NXP Semiconductors Document Number: WCT101XAV40RTDUG User's Guide Rev. 4.0, 05/2018 WCT1011A/WCT1013A Automotive MP-A9 V4.0 Run-Time Debugging 1 Introduction NXP provides the FreeMASTER GUI tool for WCT1011A/WCT1013A
Table 1 provides silicon errata information that relates to the masks 0M55B, 1M55B, and M55B of the MC9328MX21S (i.mx21s) applications processor.
Freescale Semiconductor Chip Errata Document : MC9328MX21SCE Rev. 4, 11/2012 MC9328MX21S Chip Errata for Masks:,, Table 1 provides silicon errata information that relates to the masks,, and of the MC9328MX21S
WPR1500-LDO MP Receiver V2.1 Reference Design User s Guide
NXP Semiconductors User s Guide Document Number: WPR1500LDOMPUG Rev. 0, 09/2016 WPR1500-LDO MP Receiver V2.1 Reference Design User s Guide 1 Introduction This document describes how to use the WPR1500-LDO
Freescale MQX USB Stack for TWR-K24F120M GA User s Guide
Freescale Semiconductor Document Number: USBTWRK24F120MUG User s Guide Rev. 1.0, 08/2014 Freescale MQX USB Stack for TWR-K24F120M GA User s Guide 1 Read Me First This document describes how to compile
KIT33663_EFEVB Evaluation Board Featuring the MC33663 Dual LIN Transceiver
Freescale Semiconductor User s Guide Document Number: KT66EFUG Rev..0, /0 KIT66_EFEVB Evaluation Board Featuring the MC66 Dual LIN Transceiver Figure. The KIT66_EFEVB board ( _ = J or L, which describes
Freedom FRDM-KV31F Development Platform User s Guide
Freescale Semiconductor, Inc. Document Number: FRDMKV31FUG User's Guide 0, 02/2016 Freedom FRDM-KV31F Development Platform User s Guide 1. Introduction The Freedom development platform is a set of software
ORDERING INFORMATION # of Ports Pressure Type Device Name
Freescale Semiconductor Data Sheet: Technical Data High Temperature Accuracy Integrated Silicon Pressure Sensor for Measuring Absolute Pressure, On-Chip Signal Conditioned, Temperature Compensated and
for Freescale MPC55xx/MPC56xx Microcontrollers V2.10 Quick Start
for Freescale MPC55xx/MPC56xx Microcontrollers V2.10 Quick Start CodeWarrior Development Studio for MPC55xx/MPC56xx Microcontrollers, version 2.xx Quick Start SYSTEM REQUIREMENTS Hardware Operating System