EarthLink Business SIP Trunking. Shoretel IP PBX Customer Configuration Guide

Size: px
Start display at page:

Download "EarthLink Business SIP Trunking. Shoretel IP PBX Customer Configuration Guide"

Transcription

1 EarthLink Business SIP Trunking Shoretel IP PBX Customer Configuration Guide

2 Publication History First Release: Version 2.0 April 20, 2012 CHANGE HISTORY Version Date Change Details Changed By 1.0 4/16/2011 Original Document Draft Muryle Wise 2.0 4/20/2011 Document Updates D.Thompson 2.1 4/23/2012 Document Updates D.Thompson AUTHOR: Dantley Thompson EarthLink Engineering Muryle Wise EarthLink Engineering 2

3 Table of Contents Document Purpose 4 Product Summary 4 Customer Premise Diagram 5 Media Attributes and Codec Negotiation 6 Codec Support 6 G.711u 6 G.729a 6 Packetization Time 6 DTMF Support 6 Fax and Modem Support Requirements 7 North American Numbering Plan Format 7 Quality of Service Policy 7 EarthLink SIP Trunking to IP PBX Interoperability 8 Adtran Software Version Tested 8 IP PBX Software Version Tested 8 InGate Software Version Tested 8 EarthLink Open Issues & Non-Supported Features 8 Shoretel Open Issues & Non-Supported Features 8 InGate Installation 9 IP PBX Configuration for EarthLink SIP Trunking with InGate SIParator 59 Shoretel IP PBX Configuration 59 Product Support and Contact Information 69 EarthLink SIP Trunking Turn-up Testing Procedure 70 3

4 Document Purpose The purpose of this document is to provide a detailed technical description and best practices for successful implementation of the EarthLink SIP Trunking Product for the Shoretel IP PBX with the Adtran Router and InGate SIParator. This document provides information relative to the overall network topology as well as definition and configuration standards for each device associated with the product. Also described within this document are product guidelines and product limitations. This document is to serve as product reference and guide to EarthLink Customers. Product Summary The EarthLink Business SIP Trunking product is a complete VoIP (Voice over IP) solution based on the SIP (Session Initiation Protocol) signaling protocol. The SIP Protocol is responsible for set-up and tear-down of voice calls and overall feature and functionality. The SIP Trunking product can be offered as an overlay to several of EarthLink s existing products such as Internet and MPLS based products. EarthLink Business SIP Trunking solution will be served off a MetaSphere Call Feature Server (CFS) fronted by an ACME packet SBC (Session Border Controller). The CFS acts as the centerpiece for call control and feature interaction. The EarthLink Business SIP Trunking Product will primarily use Adtran CPE (Customer Premise Equipment) along with the InGate SIParator. The MetaSphere CFS Platform is a geo-redundant, high availability solution and serves as the primary element in EarthLink s Hosted Voice and SIP Trunking Product families. In addition to the basic call control, advanced call routing functionality is available with EarthLink s SIP Trunking product with MetaSphere Enhanced Application Server (EAS) Platform which consists of multiple applications and servers integrated into high availability solution. The Acme Packet SBC masks private to public IP Address space to provide a safe and secure means of communication between the SIP Server and IP PBX. All SIP traffic destined to, or originating from the MetaSphere CFS, traverses through the ACME Packet SBC. The same policy relates to the CPE device installed at the customer premise. The Acme Packet SBC and InGate SIParator resolve NAT (Network Address Translation) related issues exposed when SIP traffic passes through a firewall. 4

5 LINK / A C T S T A T PoE G1 G2 G3 G4 CONSOLE G1 G Power over Ethernet G2 G4 Implementation Guide Customer Premise Diagram EarthLink SIP Trunking-InGate to IP PBX and Adtran for T1 based Customer 4/23/2012 Adtran 900e/Rear-View EarthLink Network 2 Adtran Eth 0/ Voice IP: EarthLink T1 from Network to Adtran NET T1 0/ x.x /30 Adtran ETH 0/1 to Customers Ethernet Switch Adtran ETH 0/2 to InGate Eth 1 InGate Eth Voice IP: x.x /30 IP PBX Private IP: x.x /24 IP PBX to Customers Ethernet Switch InGate/Rear-View InGate Eth 0 to Customers Ethernet Switch InGate Eth 0 Private IP: x.x /24 ShoreGear Switch ShoreTel Application Server Title: SIP Trunking-InGate to IP PBX and Adtran Rev.01 Date: 4/20/2012 Drawing by: Dantley Thompson Figure 1-EarthLink SIP Trunking-Connections from Adtran CPE to IP PBX 5

6 Media Attributes and Codec Negotiation Codec Support A voice codec (coder/decoder) is a hardware/software module/algorithm that takes an analog or digital voice stream and encodes it into an IP packet. For the EarthLink Business SIP Trunking Product, we currently support two (2) of the most common codec s utilized in the continental United States, G.711u and G.729a. The preferred codec offered by EarthLink in the default configuration model is G.711u, then G.729a. Basically this means that the call will negotiate using the G.711u codec first, as long as the terminating end sends G.711u as the first or primary offered codec. The paragraphs below provide more detailed information related to the codec s and other requirements associated with proper negotiation of the media/rtp. G.711u G.711u is the most common uncompressed audio codec deployed in the US. Because it is uncompressed, it supports the highest level of quality for the call. Typically the G.711u consumes 90Kbps-100Kbps per call. The standard sampling rate of 8kHz is used for the G.711u codec. G.729a G.729a is the most common codec utilized to support compressed audio utilized in the US. Because it is compressed, it is perceived to have a lower voice quality than that of G.711u, however most people would never be able to tell the difference. Typically the G.729 consumes 30Kbps-40Kbps per call. The standard sampling rate of 8kHz is used for the G.729a codec. Packetization Time Packetization Time determines how often the audio stream is sampled and how often an IP packet is created. The standard packetization times are 10ms, 20ms, 30ms, and 40ms. EarthLink Media Gateway s have been statically configured to use a 20ms packetization time. IP Phones and/or Voice Applications will need to configure their equipment for a 20ms packetization time before audio traffic can be reliably passed across the EarthLink IP Voice network. DTMF Support EarthLink supports the transmission of Dual-Tone Multi-frequency (DTMF) digits through the implementation of RFC2833. This RFC covers the basis of including DTMF digits within the media/rtp path of the call. EarthLink recommends for Customers to configure their IP PBX s and/or Voice Applications to use RFC2833 to allow for DTMF to be passed properly and detected across the EarthLink IP Voice network. 6

7 Fax and Modem Support Requirements Currently, analog devices such as faxes and modems MUST be provisioned using the G.711u codec only. SIP to analog lines are supported as SIP Lines off the Adtran FXS Ports. The customer may also configure the IP PBX to use analog extensions for faxes and modems. This method can be supported utilizing the G.711u codec only. T.38 is currently not supported. North American Numbering Plan Format Currently, the EarthLink Business Hosted Voice product only supports the North American Numbering Plan Format. A Global Numbering Plan Format, such as E.164, is currently not supported. Quality of Service Policy To ensure the best possible voice quality, EarthLink will mark and match all VoIP traffic related to SIP (Session Initiation Protocol) and RTP (Real-Time Transport Protocol). EarthLink VoIP and/or Real-Time based appliances and applications are configured to use DSCP (Differentiated Services Code Point) 46 for all signaling traffic (SIP) and DSCP 46 for all Real-Time traffic (RTP) for Layer three priority. The Customers IP PBX MUST also be configured to use DSCP 46 to provide prioritization for SIP and RTP. Marking the DSCP field in the IP packet header will allow for packet classification to be matched and provide priority across EarthLink s network. This also ensures QoS specifications outlined in SLA (Service Level Agreements) can be sufficiently met between EarthLink and the customer. 7

8 EarthLink SIP Trunking to IP PBX Interoperability SIP Trunking interoperability testing was performed between EarthLink and the IP PBX. All phases of the test plan were executed against the actual configuration used in a customer deployment. The information below provides the Adtran and IP PBX software versions tested as well as an issue summary and non-supported elements discovered during compliance testing in the EarthLink Lab. Adtran Software Version Tested Adtran TA908e version A4.09 IP PBX Software Version Tested Shoretel 12.2 Build Prerequisites ShoreTel's SIP Trunking Best Practices ( dictate an InGate SIParator as a part of the solution. This manufacturer requirement was included in the certification and is needed for successful deployment with EarthLink SIP Trunking. Included are configurations for the SIParator but customer is responsible for procurement of this device. InGate Software Version Tested InGate version EarthLink Open Issues & Non-Supported Features Registration is currently not supported for the EarthLink SIP Trunking Product. When the originating calling number in present in the FROM Header, the main billing telephone number or DID belonging to the trunk group must be provided via the PAI (P- Asserted Identity) Header or via the Diversion Header on Call Transfer and Call Forward calls for the call to pass through the Metaswitch and billed correctly. Shoretel does not support DSCP 46 for all signaling traffic (SIP). Prioritization would need to be done in the network at the layer 3 level. Shoretel Open Issues & Non-Supported Features Authorization/Challenge on INVITE without Registration is not supported by the Shoretel PBX. Authorization must be turned off/ Unchecked in the Metaswitch. The Shoretel does not support any type of SIP REFER messaging. Any call transfer, Call Forwarding, or Conferencing will require additional trunks members for each leg of the call. Since each leg of the call is a new call, caller ID will not be passed through the PBX. Shoretel is currently sending media at 102 for DTMF. EarthLink requires RFC2833, which is indicated as 101 in the SDP portion of the SIP Message. A support ticket is currently opened with Shoretel to resolve this issue. 8

9 InGate Installation Physical Installation of Pre-Configured InGate Some InGate devices will be preconfigured by EarthLink prior to shipping. In the event that the device has been preconfigured, the steps below outline how to physically install the InGate device. For a preconfigured InGate, steps 1-4 below is the only steps required. If the InGate device has not been pre-configured, please start at Section 3 of this document. 1. Required Steps for Physical Installation of the Preconfigured InGate S T E Steps to be completed. P # 1 Plug the power cable into the InGate device. 2 With an Ethernet Cat.5e patch cable, connect the Ethernet port 0 (Labeled Eth0) on the InGate to the Customer s Layer 2 Ethernet Switch. This should be the same Ethernet switch that the customer s PBX is connected to. 3 With an Ethernet Cat.5e patch cable, connect the Ethernet port 1 (Labeled Eth1) on the InGate to the Adtran 908e or NetVanta router. This is typically assigned to Eth port 0/2 on the Adtran. 4 Physical Connection process for InGate complete. Expected Result Device powers on. Green light should come on above the physical Ethernet port on the Customer Layer 2 Ethernet switch that the InGate is plugged into. Green and Amber light should come on each side of the physical Ethernet port on the Adtran 908e or NetVanta Router that the InGate is plugged into. The diagram below provides a diagram of the steps listed above. 9

10 LINK / A C T S T A T PoE G1 G2 G3 G4 CONSOLE G1 G Power over Ethernet G2 G4 Implementation Guide EarthLink SIP Trunking-InGate to IP PBX and Adtran for T1 based Customer 4/23/2012 Adtran 900e/Rear-View EarthLink Network 2 Adtran Eth 0/ Voice IP: EarthLink T1 from Network to Adtran NET T1 0/ x.x /30 Adtran ETH 0/1 to Customers Ethernet Switch Adtran ETH 0/2 to InGate Eth 1 InGate Eth Voice IP: x.x /30 IP PBX Private IP: x.x /24 IP PBX to Customers Ethernet Switch InGate/Rear-View InGate Eth 0 to Customers Ethernet Switch InGate Eth 0 Private IP: x.x /24 ShoreGear Switch ShoreTel Application Server Title: SIP Trunking-InGate to IP PBX and Adtran Rev.01 Date: 4/20/2012 Drawing by: Dantley Thompson Figure 2-Example of InGate Physical Connectivity 10

11 2. Configuring the InGate using the InGate Start-up Tool 2.1 InGate Start-up Tool Overview The InGate Startup Tool is designed to simplify the initial out of the box commissioning and programming of the Network Topology and SIP Trunk deployments. The tool will automatically configure the InGate SIParator to work with the IP-PBX and EarthLink Business SIP Trunking Product. The Start-up Tool automatically defines most of the routing and configuration needed to enable communication between the customers IP-PBX and EarthLink over SIP Trunks. Thanks to detailed interoperability testing, InGate has been able to create this tool with pre-configured set-up for several of the leading IP-PBX vendors and ITSPs. The InGate Startup Tool is available free of charge for InGate SIParators. Get the latest version of the Startup Tool at Make sure that you always have the latest version of the configuration tool as InGate continuously adds new vendors once interoperability testing is complete. The Startup Tool will install and run on any Windows 2000, Windows XP, Windows Vista, and on Linux operating systems. Keep in mind, the InGate Startup Tool is a commissioning tool, not an alternate administration tool. This tool is meant to get an out of the box InGate started with a pre-configured setup, enough to make your first call from IP-PBX to EarthLink Business over SIP Trunks. Additional programming and administration of this InGate unit should be done through the Web Administration once the device is up an operational. 11

12 2.2 InGate Start-up Tool Installation The following procedure will guide you through the download and installation of the InGate Startup Tool on a Window XP operating system. There may be minor variances with other operating systems InGate Start-up Tool Download and Upgrade Steps 1. Go to and click Download to begin the download process. 2. Select Save to save the StartupTool-xxx.zip file to a location of your choice. 3. In the StartupTool-xxx.zip, Open or Extract/Run the StartupTool.msi file. This will begin the software installation process. 4. Select Run, in the Windows - Security Warning window. 12

13 5. Select Next to continue to install the Startup Tool. 6. Define the installation folder location you wish to install the InGate Startup Tool, who is allowed to use this Startup Tool, then select Next to confirm the entry. 7. Select Next to confirm the installation. 13

14 8. Once the installation is complete, select Close. Now the Startup Tool can be used. The Startup Tool can be found in the Start Menu or via a short-cut on the desktop. 14

15 2.3 Connecting to the InGate and the Start-up Tool From the factory, the InGate SIParator does not come preconfigured with an IP address or Password to administer the unit. Web administration is not possible unless an IP Address and Password are assigned to the unit via the Startup Tool or Console port. The following steps below describe a process to connect the InGate unit to the network then have the InGate Startup Tool assign an IP Address and Password to the Unit Physical Connection Steps and Diagrams 1. Connect Power to the Unit. 2. Connect an Ethernet cable to Eth0. This Ethernet cable should connect to an Ethernet Switch/LAN. Below are some illustrations indicating Eth0 on each of the InGate Model types. InGate 1190 Firewall and SIParator 19 (Back) InGate 1500/1550/1650 Firewall and SIParator 50/55/65 15

16 2.4 Using the InGate Start-up Tool There are three primary reasons for using the InGate Startup Tool. First, is to perform an initial Out of the Box configuration of the InGate device for the first time. Second is to change or update an existing configuration. Third is to register the unit, install a License Key, and upgrade the unit to the latest software Configure the InGate for the first time As stated earlier in this document, the InGate SIParator does not come preconfigured with a default IP address or password. Prior to starting the steps below, you must know the private IP address you want to assign Eth 0 of the InGate device. The PC/Laptop with the Startup Tool must be assigned a private IP address in the same network segment and subnet as what you will be defining for Eth 0 of the InGate device. It is required that the InGate unit and the Startup Tool are on the same LAN Subnet to which you are going to assign an IP Address to the InGate unit. Note: When configuring the unit for the first time, avoid having the Startup Tool on a PC/Laptop on a different Subnet, or across a Router, or NAT device, Tagged VLAN, or VPN Tunnel. Keep the network Simple InGate IP and Password Configuration using the Start-up Tool 1. Launch the Startup Tool 2. Select the Model type of the InGate Unit, and then click Next. Note: In the EarthLink configuration, this value will always be one of the values for SIParator 19, 50, 55, 65 or 95. The device to be selected will be noted on the Customer order information. 16

17 3. In the Select first what you would like to do, select Configure the unit for the first time. 4. In the Select first what you would like to do, select Configure SIP Trunking for the tool to configure SIP Trunking, then continue to step 5 below. Figure 3-Example of InGate Start-up Tool Initial Configuration Page Note: The InGate private side/eth 0 IP address will be defined on the Customer Order information 17

18 5. In the Inside (Interface Eth0), Enter the IP Address to be assigned to the private side / Eth 0 InGate Unit. 6. Enter the MAC Address of the InGate unit The MAC Address, must be defined identical to how it appears on the InGate device. This will be used to find the unit on the network. Note: The MAC Address can be found on the sticker, usually attached to the bottom or back of the unit 7. In the Select a Password, enter the Password to be assigned to the InGate unit. Note: The InGate Password will be defined on the Customer Order information 8. Once all required values are entered, the Contact button will become active. Press the Contact button to have the Startup Tool find the InGate unit on the network and assign the IP Address and Password. 9. The InGate will then go through the process or loading the information and reboot. 10. To continue, click on the Licenses and Upgrades tab. These steps are outlined below in section InGate License Configuration InGate License Configuration using the Start-up Tool Available online at a customer, VAR, distributor can login ( and register units, obtain software upgrades, register licenses, access documentation, and download information for the installation, configuration and use of InGate products. InGate device Registration and Licensing of the EarthLink purchased InGate devices will be performed by Purchasing and Warehouse personnel. The license file will be ed to the technician performing the installation. The.lic (License File) will be loaded the by following the steps outlined below. 18

19 1. Since the InGate device has been registered and a license file has been manually acquired, select I have the license on my PC, and click the Install button Browse to the.lic located on your PC/Laptop associated with this InGate device and select the proper license file to be installed. 19

20 3. After the license file has been selected, click on the Install button again to install the license file to the InGate device. 4. The InGate device will load the license file and reboot. 5. Click on the Network Topology tab to continue configuring device. These steps are outlined in Section 3.4.5, Network Topology, below. 20

21 2.4.4 InGate Network Topology, HTTPS Certificate, IP PBX, and EarthLink SIP Trunk Configuration using the Start-up Tool The Network Topology is where the IP Addresses, Netmask, Default Gateways, Public IP Address of NAT ed Firewall, and DNS Servers are assigned to the InGate device. The configuration of the Network Topology is dependent on the deployment (Product) type. Be sure to select the product type that matches the network setup requirements, as each type has a unique set of programming and deployment guidelines. EarthLink will deploy the InGate devices as a Standalone SIParator. All IP related information to be populated in the fields below will be indicated on the Customer order information. When deploying an InGate SIParator in a Standalone configuration, the SIParator resides between the customer private LAN network (must be on the same LAN and subnet of the IP PBX), and EarthLink s IP Voice network. The Default Gateway for the InGate SIParator will be the IP address associated with the routers Ethernet interface that connects to the InGate. Adtran TA908e and NetVanta series CPE routers will use Eth 0/2 to connect to Eth 1 of the InGate device. Typically, the EarthLink SIP Voice network is defined as a x.x /30 address and is routable across EarthLink s network for customers with and without MPLS VPN services. The customer s and/or EarthLink s supplied Firewall is parallel to and independent of the SIParator. The Firewall is the primary edge device for all data traffic out of the LAN to the Internet. The SIParator is the primary edge device for all SIP Trunk related voice traffic out of the LAN to EarthLink. Below is an example of the Network Topology page and starting at step one below outlines the configuration of the Network Topology page using the InGate Start-up Tool. 21

22 Figure 4-Example of Network Topology Page in Start-up Tool 22

23 2.4.5 Configuration steps for the InGate Network Topology 1. In Product Type, select Standalone SIParator. 2. Define the IP Address and Netmask of the inside LAN (Interface Eth0). This is the IP Address that will be used on the InGate unit to connect to the private LAN network and communicate to the IP PBX. The values in the fields below are for example only, the correct IP Address and Netmask will be indicated on the customer order information. 3. Define the Outside (Interface Eth1) IP Address and Netmask. This IP Address, typically a x.x /30 address, will be used on the EarthLink side on the InGate unit and will communicate back to EarthLink s SIP Voice Network. The values in the fields below are for example only, the correct IP Address and Netmask will be indicated on the customer order information. Note: Do Not select Use DHCP to obtain IP, make sure this box is not checked 4. Select Allow https access to web interface from Internet. The values in the fields below are for example only, the correct IP Address and Netmask will be indicated on the customer order information. 23

24 5. Enter the Default Gateway for the InGate SIParator. The Default Gateway for the InGate SIParator will be the IP Address assigned to Eth 0/2 on the Adtran TA or NetVanta router or the IP Address supplied by the customer. The correct InGate Gateway IP address will be indicated on the customer order information. The values in the fields below are for example only, the correct IP Address and Netmask will be indicated on the customer order information. 6. Enter EarthLink s Primary and Secondary Voice DNS server IP addresses in these DNS server fields. Primary DNS: Secondary DNS: Once all fields have been complete, click on the IP-PBX tab at the top of the Window. 24

25 8. The Create Certificate for HTTPS Access window will be displayed 9. Fill out the field identical to what is indicated in the illustration below, then click OK 10. Once you click OK the IP-PBX page is available for modification. Continue the installation by clicking on the IP-PBX tab and following the steps outlined in the IP-PBX, Section below. 25

26 2.4.6 Configuration steps for the InGate IP-PBX The IP-PBX section is where the IP Addresses and Domain location are provided to the InGate unit. The configuration of the IP-PBX will allow the InGate unit to know the location of the IP-PBX to direct SIP traffic for use with SIP Trunking and Remote Phones. The IP Address of the IP-PBX must be on the same network subnet as the IP Address of the inside interface of the InGate unit. InGate has confirmed interoperability with many of the leading IP-PBX vendors. Follow the steps below to configure the InGate for the type of IP-PBX the InGate will connect to. Figure 5-Example of InGate Start-up Tool IP-PBX Page 26

27 1. In the IP-PBX Type drop down list, select Shoretel as the IP PBX type. InGate has confirmed interoperability with many of the leading IP-PBX vendors. The unique requirements of the vendor testing are contained in the Startup Tool. Note: The IP-PBX system type and associated IP address will be defined on the Customer Order information 27

28 2. Enter the IP Address of the IP-PBX. The IP Address must be on the same private LAN/ subnet as the private side, Eth 0, of the InGate unit. 3. This completes the IP-PBX portion of the Start-up Tool. Next, continue to the ITSP tab and follow the steps outlined in Section 3.4.7, Configuration steps for the ITSP. 28

29 2.4.7 Configuration steps for the InGate ITSP The ITSP section is where all of the attributes of the SIP Trunking Service Provider are programmed. Details like the IP Addresses or Domain, DIDs, Authentication Account information, Prefixes, and PBX local number are configured on this page. The configuration of the ITSP will allow for the InGate unit to know the location of the ITSP to direct SIP traffic for the use with SIP Trunking. InGate has confirmed interoperability with many of the leading ITSP vendors, such as EarthLink. Starting at step one below, follow these steps to configure the InGate as EarthLink as the Service Provider. 1. In the ITSP drop down list, select Deltacom. Note: Service Providers come in one of two flavors, either they have a trusted IP deployment or they require a Registration account. Although EarthLink s implementation is a trusted IP deployment model, calls are still challenged and required to authenticate to the MetaSwitch Application Server. 29

30 2. In the Account Information section, enter the Authentication name, Domain, and Password. The information entered in the fields below will be indicated on the Customer order information. 3. Enter the DID (Username) which the InGate will authenticate to EarthLink. The information entered in the fields below will be indicated on the Customer order information. 4. This completes the last step for configuring the InGate device. Click the Upload Configuration tab at the top of the Start-up Tool Window. Next we will upload the configuration to the unit as outlined in steps below in Section Uploading the configuration. 30

31 2.4.8 Configuration steps for the InGate Upload Configuration At this point the Startup Tool has all the information required to push a database into the InGate unit. The Startup Tool can also create a backup file for later use. Follow the steps below to upload the configuration into the InGate device. 1. Press the Upload button. Upon pressing the Upload button the Startup Tool will push a database into the InGate unit. 31

32 2. When the Startup has finished uploading the database a window will appear. Click OK. The Startup Tool will launch a default browser and direct you to the InGate Web GUI. 3. Although the Startup Tool has pushed a database into the InGate unit, the changes have not been applied to the unit. To apply the changes follow the steps starting with step 4 below. 4. Login to the device with the credentials below. Username: admin Password: (password specified on the customer order information) 32

33 5. Once logged into the unit click on Administration 33

34 6. Press Apply Configuration to apply the changes to the InGate unit. 7. A new page will appear after the previous step requesting to save the configuration. Press Save Configuration to complete the saving process. 8. Once this is complete, the InGate device configuration via the start-up tool process is complete. The steps outlined below provide detail to make the required changes to connect to the EarthLink MetaSwitch Platform. 34

35 2.4.9 InGate configuration for connecting to EarthLink s MetaSwitch Application Server Once the InGate Start-up Tool process has been completed, the steps below outlines the required configuration to insure the SIP messaging and SIP authentication work properly to EarthLink s MetaSwitch Call Feature Server. The steps below do not have to be performed in any particular order, but must be applied and saved once complete. 1. Open Internet Explorer and input the IP Address assigned to Eth 0 of the InGate in the URL field as (Ex: if accessing from the customers private network. If accessing remotely from the EarthLink network, input the IP Address assigned to Eth 1 of the InGate in the URL field as (Ex: or address for MPLS customers. 35

36 2. When the login screen appears, type in the user name and password in to the appropriate fields. The login user name is admin and the password is specified on the order information. 3. Once logged in, click on the Network tab. 4. Once the Network page appears, click on the Networks and Computers tab. 36

37 37

38 5. Located in the ITSP_IP row, select and delete the IP specified for the ITSP_IP under the DNS Name or IP Address field. 38

39 6. Next, input the correct IP address in the ITSP_IP row, for the ITSP_IP under the DNS Name or IP Address field as specified on the order. This is the EarthLink Acme Packet SBC IP address. 39

40 7. Once complete, click Save. 40

41 8. Next, click on the SIP Traffic tab at the top of the page. 41

42 9. Then, click on the SIP Accounts sub-tab under the SIP Traffic tab. 42

43 10. Under the Account type field near the bottom right of the SIP Accounts page click on the drop down arrow and select Domain. 43

44 11. Once Domain has been selected, click Save. 44

45 12. Next, click on the Dial Plan sub-tab under the SIP Traffic tab. 45

46 13. Then, scroll down to the Forward To Header on the Dial Plan page. 46

47 14. Under the Forward To header, one of the Names of the rows is Deltacom. In the Deltacom row, under the Use This Account header, use the drop down menu, to select the correct SIP Account. This should match the account on the specified on the SIP Accounts tab. 47

48 15. Once the SIP Account is selected, next highlight and delete the contents in the field Or this Reg Expr in the same Deltacom row. 48

49 16. Once complete with these two steps the Forward To row for Deltacom should look like the example below, except the SIP account will have a different number or set of characters. 49

50 17. Next, scroll to the bottom of the page and click Save. 50

51 18. Next, click on the Routing sub-tab under the SIP Traffic tab. 51

52 19. On the Routing page, click in the check box under the Delete Row header under the DNS Override for SIP Requests field. This box should not show a check mark to properly delete the row. 52

53 20. Next, scroll to the bottom of the page and click Save. 53

54 21. Next, scroll up to the top of the page click on the Administration tab. 54

55 22. Click the Save/Load Configuration sub-tab below the Administration tab. 55

56 23. Click Apply Configuration. 56

57 24. Click Save Configuration. 57

58 25. After clicking on Save Configuration and the unit updates with the changes, the main Administration page should display and state Configuration applied and saved. 26. This completes the InGate configuration process. ****For final installation and configuration acceptance of the InGate contact**** Dantley Thompson Systems Engineer EarthLink Business E: O: M:

59 Service Implementation Guide IP PBX Configuration for EarthLink SIP Trunking with InGate SIParator The steps below provide a step by step guide for configuration of the Shoretel IP PBX for the EarthLink SIP Trunking Product. Basic configuration of the Shoretel Application should be complete and the ShoreGear switch and Shoretel server running the application MUST be connected to the LAN prior to configuring the system for SIP Trunking. Shoretel IP PBX Configuration The following screen-shots below are using Shoretel 12.2 Build These steps outline the configuration of the Appliance 100 Planning, Installation and Administration Guide to work with EarthLink s SIP Trunking product with the InGate SIParator. For more detailed information the Shoretel Knowledgebase application can be used. Setup configuration of the 40/8 (Shoretel PBX) To configure the IP address manually, you need the following: Valid IP address for the segment in which you want to install the SA-100. Computer with terminal emulation software installed. Null modem DB-9 serial cable. Step 1 Connect the DB-9 serial cable to the serial port on the back panel of the SA- 100 to the serial port on a computer. Step 2 Hook up the SA-100 power cable and turn the unit and computer on. NOTE The SA-100 performs a start-up process when it is turned on. A sequence of numbers flash on the LED panel during start up, and a solid LED appears when the process is complete. The process takes about 30 seconds. Step 3 On the computer, start a terminal emulation program and set the following parameters: On the computer, start a terminal emulation program and set the following parameters: Baud rate: bps Data Bits: 8 Parity: None Stop Bit: 1 Flow control: None At the Login prompt, type the user ID required to enter the CLI interface and press Enter. The default login name is admin. The Password prompt appears. At the Password prompt, type the password required to enter the CLI interface and press Enter. The default password is ShoreTel. The ShoreTel command line interface as shown in Figure 5-2 appears. 59

60 Type 3 and press Enter to change the system configuration. The Change System Type 6 and press Enter to disable DHCP. The DHCP prompt appears. Type n and press Enter to disable DHCP. Type 1 and press Enter. The Change IP address prompt appears Type the IP address that you want to assign to the SA-100 and press Enter. Type 2 and press Enter. The Change IP subnet mask prompt appears. Type the IP address of the subnet where the SA-100 is to appear. Type 3 and press Enter. The Change gateway IP address prompt appears. Type the IP address of the gateway that you want the SA-100 to use. Type 0 and Enter to return to the Change System Congifuration menu Type 4 and press Enter to reboot. The prompt Are you sure you want to reboot? appears. Type y. The prompt Save your changes? appears. Type y. The SA-100 will save the static IP settings and reboot. 60

61 Shoretel SIP Trunk License Verification Confirm Shoretel is licensed for SIP Trunk Channels. The number of Instances will determine how many concurrent calls can be handled simultaneously. From Shoretel Director From the Navigation Pane, Administration, Site Parameters, License, Key Select new and enter the key code provided by Shoretel and a description, and save. Once you have entered your key codes select Register and Request System Key 61

62 Turning off Port 5004 for RTP Launch ShoreWare Director Click Administration > Call Control > Options. The Call Control Options page appears. Set the DTMF payload to 101 for RFC

63 Set to Diffserv Dec. to 184. This will set DSCP to 46. Uncheck the Always Use Port 5004 for RTP check box. Codec Option In the ShoreWare Director pane, click Administration > Call Control > Codec List Select New and add two Codec list one for G.711 only, and one for G.729 prefer. Enter a new name for G.711 only Highlight PCMU/8000 and add to Codec List members Enter a new name for G.729 preferred, G.711 optional. 63

64 Highlight G729/8000, and add to Codec list members. Highlight PCMU/8000, and add to Codec list members.. Highlight PCMA/8000, and add to Codec list Adding a SA-100 to a ShoreTel Site In the ShoreWare Director pane, click Administration > Platform Hardware > Voice Switches/Service Appliances > Primary Select Site Select Type Select Go ShoreTel site parameters In the ShoreWare Director pane, click Administration > Site > Double Click on Site 64

65 Select Site Local Area Code Drop down to select codec list previously defined. Drop down to select codec list previously defined 65

66 Enter Name and description. Click on find switches, select IP of switch you would like to add. Example Configuration Five SIP Phones, Five SIP Trunks, Four conference ports, and one FXS line. Shoretel has a Harmonic Converter that provide RJ21X conversion to the 25 pair Amphenol. If not pairs 5/30 port 1, 6/31 port 2, and so on. Adding an SIP trunk Group In the ShoreWare Director pane, click Administration > Trunks > Trunk Group Select Go to add a SIP trunk group in the headquarters site. 66

67 Inter Name of Trunk Group From drop down select _ATTBVOIP Enter the number of digits expected from the Telco. User defined, used to map DID to extension. Drop down select user group that will use this Trunk Group. Enter access digit for outside line. Local Area Code Billing Number Trunking Services are customer 67

68 Trunking Digit Manipulation leave all fields unchecked. Adding an SIP trunk Members In the ShoreWare Director pane, click Administration > Trunk > Individual Trunks Select GO to add trunk members. Enter Name Drop down, select switch. Repeat for each member. Enter the I.P. of the InGate Private I.P. 68

69 Product Support and Contact Information The information below provides contact information for assistance in configuration and troubleshooting EarthLink s SIP Trunking service. EarthLink Support: (800) or 24x7 Support Availability Shoretel Support (NTAC): (877) or o o 24x7 Support Availability 69

70 EarthLink SIP Trunking Turn-up Testing Procedure To ensure proper call negotiation can be established between EarthLink and the IP PBX, the test steps below MUST be executed during the initial turn-up process. SIP Trunking Test Steps: 1. Test an outbound call to a Local Number. Check for Ring-back, 2-way Audio, and Call Quality. 2. Test an outbound call to a Long Distance Number. Check for Ring-back, 2-way Audio, and Call Quality. 3. Test an outbound call to an International Number. Check for Ring-back, 2-way Audio, and Call Quality. 4. Test an outbound call to a Toll-Free Number. Check for Ring-back, 2-way Audio, and Call Quality. 5. Test an inbound call that lasts greater than 10 minutes 6. Test an outbound call that lasts greater than 10 minutes 7. Test simultaneous inbound and outbound calls to PSTN 8. Test an outbound Call to Operator 0 9. Test an outbound Call to Directory Assistance Test a 911 Call (IDENTIFY TO THE 911 OPERATOR THAT THIS IS A TEST). Ask them to provide phone number, address and secondary or alternate number if available. 11. Test an inbound call to an internal DID. Check for Ring-back, 2-way Audio, and Call Quality. 12. Test an inbound call to Auto-Attendant. Check DTMF and Call Quality 13. Test an outbound call to an Auto-Attendant/IVR and verify DTMF 14. Test Call Transfer off-site 15. Test Call Forward off-site Notes: 70

EarthLink Business SIP Trunking. ShoreTel 14.2 IP PBX Customer Configuration Guide

EarthLink Business SIP Trunking. ShoreTel 14.2 IP PBX Customer Configuration Guide EarthLink Business SIP Trunking ShoreTel 14.2 IP PBX Customer Configuration Guide Publication History First Release: Version 1.0 August 30, 2011 CHANGE HISTORY Version Date Change Details Changed By 1.0

More information

EarthLink Business SIP Trunking. Allworx 6x IP PBX SIP Proxy Customer Configuration Guide

EarthLink Business SIP Trunking. Allworx 6x IP PBX SIP Proxy Customer Configuration Guide EarthLink Business SIP Trunking Allworx 6x IP PBX SIP Proxy Customer Configuration Guide Publication History First Release: Version 1.0 August 30, 2011 CHANGE HISTORY Version Date Change Details Changed

More information

EarthLink Business SIP Trunking. Toshiba IPEdge 1.6 Customer Configuration Guide

EarthLink Business SIP Trunking. Toshiba IPEdge 1.6 Customer Configuration Guide EarthLink Business SIP Trunking Toshiba IPEdge 1.6 Customer Configuration Guide Publication History First Release: Version 1.0 August 30, 2011 CHANGE HISTORY Version Date Change Details Changed By 1.0

More information

EarthLink Business SIP Trunking. Asterisk 1.8 IP PBX Customer Configuration Guide

EarthLink Business SIP Trunking. Asterisk 1.8 IP PBX Customer Configuration Guide EarthLink Business SIP Trunking Asterisk 1.8 IP PBX Customer Configuration Guide Publication History First Release: Version 1.0 August 30, 2011 CHANGE HISTORY Version Date Change Details Changed By 1.0

More information

EarthLink Business SIP Trunking. Cisco CME IP PBX Customer Configuration Guide

EarthLink Business SIP Trunking. Cisco CME IP PBX Customer Configuration Guide EarthLink Business SIP Trunking Cisco CME IP PBX Customer Configuration Guide Publication History First Release: Version 1.0 August 30, 2011 CHANGE HISTORY Version Date Change Details Changed By 1.0 8/30/2011

More information

Application Note Startup Tool - Getting Started Guide

Application Note Startup Tool - Getting Started Guide Application Note Startup Tool - Getting Started Guide 07 July 2008 Startup Tool Table of Contents 1 INGATE STARTUP TOOL...1 2 STARTUP TOOL INSTALLATION...2 3 CONNECTING THE INGATE FIREWALL/SIPARATOR...5

More information

Application Note 3Com VCX Connect with SIP Trunking - Configuration Guide

Application Note 3Com VCX Connect with SIP Trunking - Configuration Guide Application Note 3Com VCX Connect with SIP Trunking - Configuration Guide 28 May 2009 3Com VCX Connect Solution SIP Trunking Table of Contents 1 3COM VCX CONNECT AND INGATE... 1 1.1 SIP TRUNKING SUPPORT...

More information

Startup Tool TG - Getting Started Guide

Startup Tool TG - Getting Started Guide Startup Tool TG - Getting Started Guide For Classic Ingate SIParator Version 5.0.10 or later Document revision 17B, February 20, 2017 1(24) Table of Contents 0 Quick Start... 2 1 Ingate Startup Tool TG...

More information

Application Note Configuration Guide for ShoreTel and Ingate

Application Note Configuration Guide for ShoreTel and Ingate Application Note Configuration Guide for ShoreTel and Ingate 29 August 2008 Table of Contents 1 INTRODUCTION... 1 2 SHORETEL CONFIGURATION... 2 2.1 OVERVIEW... 2 2.1.1 Version Support... 2 2.1.2 ShoreTel

More information

Application Note Asterisk BE with SIP Trunking - Configuration Guide

Application Note Asterisk BE with SIP Trunking - Configuration Guide Application Note Asterisk BE with SIP Trunking - Configuration Guide 23 January 2009 Asterisk BE SIP Trunking Table of Contents 1 ASTERISK BUSINESS EDITION AND INGATE... 1 1.1 SIP TRUNKING SUPPORT... 2

More information

Application Note Configuration Guide for ShoreTel and Ingate with PAETEC

Application Note Configuration Guide for ShoreTel and Ingate with PAETEC Application Note Configuration Guide for ShoreTel and Ingate with PAETEC 29 August 2008 Table of Contents 1 INTRODUCTION... 1 2 PAETEC CONFIGURATION... 2 2.1 CPE REQUIREMENTS... 2 2.2 PAETEC S DYNAMIC

More information

Application Note. Microsoft OCS 2007 Configuration Guide

Application Note. Microsoft OCS 2007 Configuration Guide Application Note Microsoft OCS 2007 Configuration Guide 15 October 2009 Microsoft OCS 2007 Configuration Guide Table of Contents 1 MICROSOFT OCS 2007 AND INGATE... 1 1.1 SIP TRUNKING SUPPORT... 2 2 INGATE

More information

Application Note Asterisk BE with Remote Phones - Configuration Guide

Application Note Asterisk BE with Remote Phones - Configuration Guide Application Note Asterisk BE with Remote Phones - Configuration Guide 15 January 2009 Asterisk BE - Remote SIP Phones Table of Contents 1 ASTERISK BUSINESS EDITION AND INGATE... 1 1.1 REMOTE SIP PHONE

More information

Configuration Guide For Use with AT&T s IP Flexible Reach Service. Version 1/Issue 7. July 30, 2008

Configuration Guide For Use with AT&T s IP Flexible Reach Service. Version 1/Issue 7. July 30, 2008 Configuration Guide For Use with AT&T s IP Flexible Reach Service Version 1/Issue 7 July 30, 2008 Page 1 of 42 TABLE OF CONTENTS 1 Introduction... 4 2 Version Information... 6 3 Special Notes... 7 ShoreTel

More information

Configuration Guide. For Use with AT&T s. IP Flexible Reach-Enhanced Features Service

Configuration Guide. For Use with AT&T s. IP Flexible Reach-Enhanced Features Service Product: ShoreTel Ingate AT&T IP Flexible Reach- Enhanced Features Service I n n o v a t i o n A p p N o t e IN-14014 Date: April, 2014 System version: ShoreTel 14.2 Ingate 5.x N e t w o r k Configuration

More information

Application Notes for Configuring Cablevision Optimum Voice SIP Trunking with Avaya IP Office - Issue 1.1

Application Notes for Configuring Cablevision Optimum Voice SIP Trunking with Avaya IP Office - Issue 1.1 Avaya Solution & Interoperability Test Lab Application Notes for Configuring Cablevision Optimum Voice SIP Trunking with Avaya IP Office - Issue 1.1 Abstract These Application Notes describe the procedures

More information

Application Notes for Configuring Tidal Communications tnet Business VoIP with Avaya IP Office using SIP Registration - Issue 1.0

Application Notes for Configuring Tidal Communications tnet Business VoIP with Avaya IP Office using SIP Registration - Issue 1.0 Avaya Solution & Interoperability Test Lab Application Notes for Configuring Tidal Communications tnet Business VoIP with Avaya IP Office using SIP Registration - Issue 1.0 Abstract These Application Notes

More information

Spectrum Enterprise SIP Trunking Service ShoreTel Shoregear 90 R14.2 Build (with Ingate SIParator) IP PBX Configuration Guide

Spectrum Enterprise SIP Trunking Service ShoreTel Shoregear 90 R14.2 Build (with Ingate SIParator) IP PBX Configuration Guide Spectrum Enterprise SIP Trunking Service ShoreTel Shoregear 90 R14.2 Build 19.43.1700.00 (with Ingate SIParator) IP PBX Configuration Guide About Spectrum Enterprise: Spectrum Enterprise is a division

More information

Avaya PBX SIP TRUNKING Setup & User Guide

Avaya PBX SIP TRUNKING Setup & User Guide Avaya PBX SIP TRUNKING Setup & User Guide Nextiva.com (800) 285-7995 2 P a g e Contents Description... 3 Avaya IP PBX Configuration... 3 Licensing and Physical Hardware... 4 System Tab Configuration...

More information

Application Notes for Configuring CenturyLink SIP Trunking with Avaya IP Office Issue 1.0

Application Notes for Configuring CenturyLink SIP Trunking with Avaya IP Office Issue 1.0 Avaya Solution & Interoperability Test Lab Application Notes for Configuring CenturyLink SIP Trunking with Avaya IP Office 6.1 - Issue 1.0 Abstract These Application Notes describe the procedures for configuring

More information

Connecting IP-PBX to BroadSoft's BroadCloud SIP Trunk using AudioCodes Mediant SBC

Connecting IP-PBX to BroadSoft's BroadCloud SIP Trunk using AudioCodes Mediant SBC Quick Guide AudioCodes Mediant Session Border Controllers (SBC) Connecting IP-PBX to BroadSoft's BroadCloud SIP Trunk using AudioCodes Mediant SBC Version 7.2 Introduction See Chapter 1 Obtain Software

More information

ShoreTel, Ingate & Rogers Communications for SIP

ShoreTel, Ingate & Rogers Communications for SIP I n n o v a t i o n N e t w o r k A p p N o t e IN- 15073 Date : Nov 2015 Product: ShoreTel Ingate Rogers Communications System version: ShoreTel 14.2 ShoreTel, Ingate & Rogers Communications for SIP Trunking

More information

Application Notes for Avaya IP Office Release 8.0 with AT&T Business in a Box (BIB) over IP Flexible Reach Service Issue 1.0

Application Notes for Avaya IP Office Release 8.0 with AT&T Business in a Box (BIB) over IP Flexible Reach Service Issue 1.0 Avaya Solution & Interoperability Test Lab Application Notes for Avaya IP Office Release 8.0 with AT&T Business in a Box (BIB) over IP Flexible Reach Service Issue 1.0 Abstract These Application Notes

More information

Application Notes for Phonect SIP Trunk Service and Avaya IP Office 7.0 Issue 1.0

Application Notes for Phonect SIP Trunk Service and Avaya IP Office 7.0 Issue 1.0 Avaya Solution & Interoperability Test Lab Application Notes for Phonect SIP Trunk Service and Avaya IP Office 7.0 Issue 1.0 Abstract These Application Notes describe the procedures for configuring Session

More information

Ingate Firewall & SIParator Product Training. SIP Trunking Focused

Ingate Firewall & SIParator Product Training. SIP Trunking Focused Ingate Firewall & SIParator Product Training SIP Trunking Focused Common SIP Applications SIP Trunking Remote Desktop Ingate Product Training Common SIP Applications SIP Trunking A SIP Trunk is a concurrent

More information

Application Notes for Configuring EarthLink SIP Trunk Service with Avaya IP Office using UDP/RTP - Issue 1.0

Application Notes for Configuring EarthLink SIP Trunk Service with Avaya IP Office using UDP/RTP - Issue 1.0 Avaya Solution & Interoperability Test Lab Application Notes for Configuring EarthLink SIP Trunk Service with Avaya IP Office using UDP/RTP - Issue 1.0 Abstract These Application Notes describe the procedures

More information

Application Notes for Configuring Windstream SIP Trunking with Avaya IP Office - Issue 1.0

Application Notes for Configuring Windstream SIP Trunking with Avaya IP Office - Issue 1.0 Avaya Solution & Interoperability Test Lab Application Notes for Configuring Windstream SIP Trunking with Avaya IP Office - Issue 1.0 Abstract These Application Notes describe the procedures for configuring

More information

Application Note. ShoreTel / Ingate / Verizon Business SIP Trunking. 09 June 2017 Version 1 Issue 2

Application Note. ShoreTel / Ingate / Verizon Business SIP Trunking. 09 June 2017 Version 1 Issue 2 Product: ShoreTel Ingate Verizon Business I n n o v a t i o n N e t w o r k A p p N ote TPP-10466 Date: October, 2012 System version: ShoreTel 13.x Application e ShoreTel / Ingate / Verizon Business SIP

More information

DSP-1282 & DSP-1283 Crestron Avia DSP with ShoreTel Connect Client Software Configuration Guide Crestron Electronics, Inc.

DSP-1282 & DSP-1283 Crestron Avia DSP with ShoreTel Connect Client Software Configuration Guide Crestron Electronics, Inc. DSP-1282 & DSP-1283 Crestron Avia DSP with ShoreTel Connect Client Software 21.80.7840.0 Configuration Guide Crestron Electronics, Inc. The product warranty can be found at www.crestron.com/warranty. The

More information

ShoreTel & Windstream for SIP Trunking (Native)

ShoreTel & Windstream for SIP Trunking (Native) Product: ShoreTel Windstream Metaswitch Network I n n o v a t i o n N e t w o r k A p p N o t e IN-14018 Date : March, 2014 System version: ShoreTel 14.2 ShoreTel & Windstream for SIP Trunking (Native)

More information

ShoreTel with SIParator version 12.2

ShoreTel with SIParator version 12.2 ShoreTel with SIParator version 12.2 Table of Contents REVISION HISTORY.2 NON DISCLOSURE AGREEMENT 2 1 Introduction...3 2 Executive Summary..6 3 Software and Hardware Equipment Requirements for Testing

More information

DSP-1282 & DSP-1283 Crestron Avia DSP with ShoreTel Connect Client Software

DSP-1282 & DSP-1283 Crestron Avia DSP with ShoreTel Connect Client Software DSP-1282 & DSP-1283 Crestron Avia DSP with ShoreTel Connect Client Software 21.80.7840.0 Configuration Guide Crestron Electronics, Inc. The product warranty can be found at www.crestron.com/warranty. The

More information

Application Notes for TelStrat Engage Record Version 3.3 with Avaya Business Communication Manger Release 6.0 VoIP Recording Issue 1.

Application Notes for TelStrat Engage Record Version 3.3 with Avaya Business Communication Manger Release 6.0 VoIP Recording Issue 1. Avaya Solution & Interoperability Test Lab Application Notes for TelStrat Engage Record Version 3.3 with Avaya Business Communication Manger Release 6.0 VoIP Recording Issue 1.0 Abstract These Application

More information

Configuration Guide. Ingate SIParator /Firewall E-SBC with Microsoft Office 365 Unified Messaging (UM)

Configuration Guide. Ingate SIParator /Firewall E-SBC with Microsoft Office 365 Unified Messaging (UM) Configuration Guide Ingate SIParator /Firewall E-SBC with Microsoft Office 365 Unified Messaging (UM) May 2015 Page 1 of 32 Table of Contents 1 Introduction... 3 1.1 Before you begin... 3 1.2 Compatibilities

More information

Application Notes for Multi-Tech FaxFinder IP with Avaya IP Office Issue 1.0

Application Notes for Multi-Tech FaxFinder IP with Avaya IP Office Issue 1.0 Avaya Solution & Interoperability Test Lab Application Notes for Multi-Tech FaxFinder IP with Avaya IP Office Issue 1.0 Abstract These Application Notes describe the configuration steps required for Multi-Tech

More information

Abstract. Avaya Solution & Interoperability Test Lab

Abstract. Avaya Solution & Interoperability Test Lab Avaya Solution & Interoperability Test Lab Application Notes for SIP Trunking Using Verizon Business IP Trunk SIP Trunk Service and Avaya IP Office Release 6.1, Using REFER and DNS SRV Issue 1.0 Abstract

More information

Unofficial IRONTON ITSP Setup Guide

Unofficial IRONTON ITSP Setup Guide September 13 Unofficial IRONTON ITSP Setup Guide Author: Zultys Technical Support This unofficial configuration guide was created to assist knowledgeable vendors with configuring the Zultys MX Phone System

More information

Abstract. Avaya Solution & Interoperability Test Lab

Abstract. Avaya Solution & Interoperability Test Lab Avaya Solution & Interoperability Test Lab Application Notes for Configuring SIP Trunking between the PAETEC Broadsoft based SIP Trunking Solution and an Avaya IP Office Telephony Solution Issue 1.0 Abstract

More information

SV9100 SIP Trunking Service Configuration Guide for Cable ONE Business

SV9100 SIP Trunking Service Configuration Guide for Cable ONE Business SV9100 SIP Trunking Service Configuration Guide for Cable ONE Business NDA-31871 Issue 1.0 NEC Enterprise Communication Technologies, Inc. reserves the right to change the specifications, functions, or

More information

Application Notes for Configuring the ADTRAN NetVanta UC Server with Avaya IP Office 6.1 Issue 1.0

Application Notes for Configuring the ADTRAN NetVanta UC Server with Avaya IP Office 6.1 Issue 1.0 Avaya Solution & Interoperability Test Lab Application Notes for Configuring the ADTRAN NetVanta UC Server with Avaya IP Office 6.1 Issue 1.0 Abstract These Application Notes describe the procedure for

More information

Abstract. Avaya Solution & Interoperability Test Lab

Abstract. Avaya Solution & Interoperability Test Lab Avaya Solution & Interoperability Test Lab Application Notes for Avaya Aura Communication Manager 5.2.1, Avaya Aura Session Manager 6.1 and Avaya Aura Session Border Controller 6.0.3 with AT&T IP Toll

More information

Application Notes for Configuring the XO Communications SIP Trunking Service with Avaya IP Office 10.0 Issue 1.0

Application Notes for Configuring the XO Communications SIP Trunking Service with Avaya IP Office 10.0 Issue 1.0 Avaya Solution & Interoperability Test Lab Application Notes for Configuring the XO Communications SIP Trunking Service with Avaya IP Office 10.0 Issue 1.0 Abstract These Application Notes describe the

More information

Application Notes for OneAccess-Telstra Business SIP with Avaya IP Office Release 11 SIP Trunking - Issue 1.0

Application Notes for OneAccess-Telstra Business SIP with Avaya IP Office Release 11 SIP Trunking - Issue 1.0 Avaya Solution & Interoperability Test Lab Application Notes for OneAccess-Telstra Business SIP with Avaya IP Office Release 11 SIP Trunking - Issue 1.0 Abstract These Application Notes illustrate a sample

More information

Application Notes for Configuring SIP Trunking Using Verizon Business IP Contact Center VoIP Inbound and Avaya IP Office Release 6.1 Issue 1.

Application Notes for Configuring SIP Trunking Using Verizon Business IP Contact Center VoIP Inbound and Avaya IP Office Release 6.1 Issue 1. Avaya Solution & Interoperability Test Lab Application Notes for Configuring SIP Trunking Using Verizon Business IP Contact Center VoIP Inbound and Avaya IP Office Release 6.1 Issue 1.0 Abstract These

More information

Abstract. Avaya Solution & Interoperability Test Lab

Abstract. Avaya Solution & Interoperability Test Lab Avaya Solution & Interoperability Test Lab Application Notes for Uecomm/Optus Evolve SIP Trunking Service with Avaya IP Office 9.1.6 and Avaya Session Border Controller for Enterprise 7.0 - Issue 1.0 Abstract

More information

Dolby Conference Phone. Configuration guide for Avaya Aura Platform 6.x

Dolby Conference Phone. Configuration guide for Avaya Aura Platform 6.x Dolby Conference Phone Configuration guide for Avaya Aura Platform 6.x Version 3.2 28 June 2017 Copyright 2017 Dolby Laboratories. All rights reserved. Dolby Laboratories, Inc. 1275 Market Street San Francisco,

More information

: Microsoft. Updated : 7/24/2009 READ THIS BEFORE YOU PROCEED

: Microsoft. Updated : 7/24/2009 READ THIS BEFORE YOU PROCEED Microsoft Exchange Server 2010 Unified Messaging SBC Configuration Notes Ingate SIParator By : Microsoft Updated : 7/24/2009 READ THIS BEFORE YOU PROCEED This document is for informational purposes only

More information

UCM6102/6104/6108/6116 Configuration

UCM6102/6104/6108/6116 Configuration UCM6102/6104/6108/6116 Configuration This document introduces manual configuration steps performed for interoperability testing between AccessLine and Grandstream UCM6102/6104/6108/6116. Configuration

More information

CCS-UC-1 SIP Endpoint with ShoreTel Connect System Configuration Guide Crestron Electronics, Inc.

CCS-UC-1 SIP Endpoint with ShoreTel Connect System Configuration Guide Crestron Electronics, Inc. CCS-UC-1 SIP Endpoint with ShoreTel Connect System 21.80.7840.0 Configuration Guide Crestron Electronics, Inc. Crestron product development software is licensed to Crestron dealers and Crestron Service

More information

Application Notes for Configuring SIP Trunking between CenturyLink SIP Trunk (Legacy Qwest) Service and Avaya IP Office R8.0 (16) Issue 1.

Application Notes for Configuring SIP Trunking between CenturyLink SIP Trunk (Legacy Qwest) Service and Avaya IP Office R8.0 (16) Issue 1. Avaya Solution & Interoperability Test Lab Application Notes for Configuring SIP Trunking between CenturyLink SIP Trunk (Legacy Qwest) Service and Avaya IP Office R8.0 (16) Issue 1.0 Abstract These Application

More information

Application Notes for Configuring Windstream using Genband G9 SIP Trunking with Avaya IP Office Issue 1.0

Application Notes for Configuring Windstream using Genband G9 SIP Trunking with Avaya IP Office Issue 1.0 Avaya Solution & Interoperability Test Lab Application Notes for Configuring Windstream using Genband G9 SIP Trunking with Avaya IP Office 8.1 - Issue 1.0 Abstract These Application Notes describe the

More information

CUCM XO SIP Trunk Configuration Guide

CUCM XO SIP Trunk Configuration Guide QUANTiX QFlex Session Border Controller CUCM 10.0 - XO SIP Trunk Configuration Guide Release 5.6.2-9 Document revision: 01.01 www.genband.com 2 630-02102-01 QUANTiX QFlex Session Border Controller Publication:

More information

Application Notes for Configuring Fonolo In-Call Rescue with Avaya IP Office Server Edition using SIP Trunks Issue 1.0

Application Notes for Configuring Fonolo In-Call Rescue with Avaya IP Office Server Edition using SIP Trunks Issue 1.0 Avaya Solution & Interoperability Test Lab Application Notes for Configuring Fonolo In-Call Rescue with Avaya IP Office Server Edition using SIP Trunks Issue 1.0 Abstract These Application Notes describe

More information

for VoIP Gateway Series

for VoIP Gateway Series Smart Web Manager for VoIP Gateway Series www.addpac.com AddPac Technology 2010, Sales and Marketing Contents Web Connection Main Page Layout System Configuration Language, WAN Setup, LAN Setup, NAT, NTP,

More information

Abstract. Avaya Solution & Interoperability Test Lab

Abstract. Avaya Solution & Interoperability Test Lab Avaya Solution & Interoperability Test Lab Application Notes for Configuring SIP Trunking between Metaswitch MetaSphere CFS 7.3 with Metaswitch Perimeta Session Border Controller 3.1.0 and Avaya IP Office

More information

Dolby Conference Phone. Configuration guide for Avaya Aura Platform 6.x

Dolby Conference Phone. Configuration guide for Avaya Aura Platform 6.x Dolby Conference Phone Configuration guide for Avaya Aura Platform 6.x Version 3.1 22 February 2017 Copyright 2017 Dolby Laboratories. All rights reserved. Dolby Laboratories, Inc. 1275 Market Street San

More information

How to Install an Ingate E-SBC in Stand-alone Firewall mode or DMZ / LAN mode for an Aastra Teleworker Solution.

How to Install an Ingate E-SBC in Stand-alone Firewall mode or DMZ / LAN mode for an Aastra Teleworker Solution. How to Install an Ingate E-SBC in Stand-alone Firewall mode or DMZ / LAN mode for an Aastra Teleworker Solution. March, 2013 Ingate Systems Page: 1(11) Table of Content 1 Introduction... 3 2 10 step installation

More information

Innovation Networking App Note

Innovation Networking App Note Innovation Networking App Note G12 Communications ShoreTel and G12 Communications for SIP Trunking (Native) 1 (877) 311-8750 sales@g12com.com Jackson St. #19390, Seattle, WA 98104 Product: ShoreTel G12

More information

Table of Contents. CRA-200 Analog Telephone Adapter 2 x Ethernet Port + 2 x VoIP Line. Quick Installation Guide. CRA-200 Quick Installation Guide

Table of Contents. CRA-200 Analog Telephone Adapter 2 x Ethernet Port + 2 x VoIP Line. Quick Installation Guide. CRA-200 Quick Installation Guide CRA-200 Analog Telephone Adapter 2 x Ethernet Port + 2 x VoIP Line Quick Installation Guide Table of Contents VoIP ATA Package Contents... 2 Checklist... 2 IMPORTANT SAFETY INSTRUCTIONS... 3 Connecting

More information

Broadvox Fusion Platform Version 1.2 ITSP Setup Guide

Broadvox Fusion Platform Version 1.2 ITSP Setup Guide November 13 Broadvox Fusion Platform Version 1.2 ITSP Setup Guide Author: Zultys Technical Support This configuration guide was created to assist knowledgeable vendors with configuring the Zultys MX Phone

More information

Abstract. Avaya Solution & Interoperability Test Lab

Abstract. Avaya Solution & Interoperability Test Lab Avaya Solution & Interoperability Test Lab Application Notes for Configuring the Ingate SIParator with Avaya SIP Enablement Services and Avaya Communication Manager to Support SIP Trunking - Issue 1.0

More information

CTX 1000 VoIP Accelerator User Guide

CTX 1000 VoIP Accelerator User Guide CTX 1000 Version 2.0 March 2007 Part #: 721-000410-00 Rev. A CTX 1000 VoIP Accelerator User Guide CTX 1000 VoIP Accelerator User Guide Version 2.0 Copyright 2007 by Converged Access Inc. Littleton, MA

More information

Abstract. Avaya Solution & Interoperability Test Lab

Abstract. Avaya Solution & Interoperability Test Lab Avaya Solution & Interoperability Test Lab Application Notes for Configuring Sotel Systems SIP Trunking with Avaya IP Office Release 8.1 and the Avaya Session Border Controller for Enterprise 6.2 Issue

More information

MITEL SIP CoE Technical. Configuration Note. Configure Mitel MiVoice Office 6.1 SP1 PR2 for use with IntelePeer SIP Trunking. SIP CoE XXX

MITEL SIP CoE Technical. Configuration Note. Configure Mitel MiVoice Office 6.1 SP1 PR2 for use with IntelePeer SIP Trunking. SIP CoE XXX MITEL SIP CoE Technical Configuration Note Configure Mitel MiVoice Office 6.1 SP1 PR2 for use with IntelePeer SIP Trunking SIP CoE 12-4940-00XXX NOTICE The information contained in this document is believed

More information

Abstract. Avaya Solution & Interoperability Test Lab

Abstract. Avaya Solution & Interoperability Test Lab Avaya Solution & Interoperability Test Lab Application Notes for Configuring a SonicWALL VPN solution with an Avaya IP Telephony Infrastructure using Avaya Aura Communication Manager Branch in a Converged

More information

Abstract. Avaya Solution & Interoperability Test Lab

Abstract. Avaya Solution & Interoperability Test Lab Avaya Solution & Interoperability Test Lab Application Notes for Configuring SIP Trunking between Sotel IP Services SIP Edge Advanced SIP Trunking Solution and an Avaya IP Office Telephony Solution Issue

More information

Allstream NGNSIP Security Recommendations

Allstream NGNSIP Security Recommendations Allstream NGN SIP Trunking Quick Start Guide We are confident that our service will help increase your organization s performance and productivity while keeping a cap on your costs. Summarized below is

More information

Spectrum Enterprise SIP Trunking Service NEC Univerge SV8100 IP PBX Configuration Guide

Spectrum Enterprise SIP Trunking Service NEC Univerge SV8100 IP PBX Configuration Guide Spectrum Enterprise SIP Trunking Service NEC Univerge SV8100 IP PBX Configuration Guide About Spectrum Enterprise: Spectrum Enterprise is a division of Charter Communications following a merger with Time

More information

Application Notes for Configuring SIP Trunking Using Verizon Business IP Contact Center VoIP Inbound and Avaya IP Office Release 8.1 Issue 1.

Application Notes for Configuring SIP Trunking Using Verizon Business IP Contact Center VoIP Inbound and Avaya IP Office Release 8.1 Issue 1. Avaya Solution & Interoperability Test Lab Application Notes for Configuring SIP Trunking Using Verizon Business IP Contact Center VoIP Inbound and Avaya IP Office Release 8.1 Issue 1.0 Abstract These

More information

Dolby Conference Phone. Configuration guide for Unify OpenScape Enterprise Express 8.0.x

Dolby Conference Phone. Configuration guide for Unify OpenScape Enterprise Express 8.0.x Dolby Conference Phone Configuration guide for Unify OpenScape Enterprise Express 8.0.x Version 3.2 28 June 2017 Copyright 2017 Dolby Laboratories. All rights reserved. Dolby Laboratories, Inc. 1275 Market

More information

Abstract. Avaya Solution & Interoperability Test Lab

Abstract. Avaya Solution & Interoperability Test Lab Avaya Solution & Interoperability Test Lab Application Notes for Configuring Avaya IP Office Release 9.0 with Avaya Session Border Controller for Enterprise Release 6.2 to support BT Ireland SIP Trunk

More information

EP502/EP504 IP PBX 1.1 Overview

EP502/EP504 IP PBX 1.1 Overview 1.1 Overview The EP502/EP504 is an embedded Voice over IP (VoIP) Server with Session Initiation Protocol (SIP) to provide IP extension phone connection for global virtual office of small-to-medium business

More information

Application Notes for Configuring SIP Trunking between McLeodUSA SIP Trunking Solution and an Avaya IP Office Telephony Solution Issue 1.

Application Notes for Configuring SIP Trunking between McLeodUSA SIP Trunking Solution and an Avaya IP Office Telephony Solution Issue 1. Avaya Solution & Interoperability Test Lab Application Notes for Configuring SIP Trunking between McLeodUSA SIP Trunking Solution and an Avaya IP Office Telephony Solution Issue 1.1 Abstract These Application

More information

Spectrum Enterprise SIP Trunking Service NEC Univerge SV9100 IP PBX Configuration Guide

Spectrum Enterprise SIP Trunking Service NEC Univerge SV9100 IP PBX Configuration Guide Spectrum Enterprise SIP Trunking Service NEC Univerge SV9100 IP PBX Configuration Guide About Spectrum Enterprise: Spectrum Enterprise is a division of Charter Communications following a merger with Time

More information

SonicWALL / Toshiba General Installation Guide

SonicWALL / Toshiba General Installation Guide SonicWALL / Toshiba General Installation Guide SonicWALL currently maintains two operating systems for its Unified Threat Management (UTM) platform, StandardOS and EnhancedOS. When a SonicWALL is implemented

More information

Application Notes for Configuring SIP Trunking between Global Crossing SIP Trunking Service and an Avaya IP Office Telephony Solution Issue 1.

Application Notes for Configuring SIP Trunking between Global Crossing SIP Trunking Service and an Avaya IP Office Telephony Solution Issue 1. Avaya Solution & Interoperability Test Lab Application Notes for Configuring SIP Trunking between Global Crossing SIP Trunking Service and an Avaya IP Office Telephony Solution Issue 1.0 Abstract These

More information

Application Notes for Configuring SIP Trunking between the Skype SIP Service and an Avaya IP Office Telephony Solution Issue 1.0

Application Notes for Configuring SIP Trunking between the Skype SIP Service and an Avaya IP Office Telephony Solution Issue 1.0 Application Notes for Configuring SIP Trunking between the Skype SIP Service and an Avaya IP Office Telephony Solution Issue 1.0 Abstract These Application Notes describe the steps to configure trunking

More information

This guide assists users to configure the Allworx VoIP Phone System and XO SIP Services.

This guide assists users to configure the Allworx VoIP Phone System and XO SIP Services. Introduction This guide assists users to configure the Allworx VoIP Phone System and XO SIP Services. Prerequisites Completed the Allworx Technical training, and the main technician is either an Allworx

More information

Page 2 Skype Connect Requirements Guide

Page 2 Skype Connect Requirements Guide Thinking about implementing Skype Connect? Read this guide first. Skype Connect provides connectivity between your business and the Skype community. By adding Skype Connect to your existing SIP-enabled

More information

Application Notes for Configuring Citel s Portico TVA with Avaya IP Office Issue 1.0

Application Notes for Configuring Citel s Portico TVA with Avaya IP Office Issue 1.0 Avaya Solution & Interoperability Test Lab Application Notes for Configuring Citel s Portico TVA with Avaya IP Office Issue 1.0 Abstract These Application Notes describe the configuration steps required

More information

Application Notes for Avaya IP Office Release 8.1 and Avaya Session Border Controller for Enterprise 6.2, with AT&T IP Toll Free Service Issue 1.

Application Notes for Avaya IP Office Release 8.1 and Avaya Session Border Controller for Enterprise 6.2, with AT&T IP Toll Free Service Issue 1. Avaya Solution & Interoperability Test Lab Application Notes for Avaya IP Office Release 8.1 and Avaya Session Border Controller for Enterprise 6.2, with AT&T IP Toll Free Service Issue 1.0 Abstract These

More information

Implementation and Planning Guide

Implementation and Planning Guide nexvortex SIP Trunking February 2018 5 1 0 S P R I N G S T R E E T H E R N D O N V A 2 0 1 7 0 + 1 8 5 5. 6 3 9. 8 8 8 8 Copyright nexvortex 2018 This document is the exclusive property of nexvortex, Inc.

More information

EdgeConnect for Amazon Web Services (AWS)

EdgeConnect for Amazon Web Services (AWS) Silver Peak Systems EdgeConnect for Amazon Web Services (AWS) Dinesh Fernando 2-22-2018 Contents EdgeConnect for Amazon Web Services (AWS) Overview... 1 Deploying EC-V Router Mode... 2 Topology... 2 Assumptions

More information

ANSEL FXS / 1 PSTN. VoIP Telephone Adaptor. User Manual V1.10

ANSEL FXS / 1 PSTN. VoIP Telephone Adaptor. User Manual V1.10 ANSEL 5518 1 FXS / 1 PSTN VoIP Telephone Adaptor User Manual V1.10 Quick Guide Step 1: Broadband (ADSL/Cable Modem) Connections for ANSEL 5518 A. Connect ANSEL 5518 WAN port to ADSL NAT Router as the following

More information

TECHNICAL GUIDE to access Business Talk IP SIP IPBX Shoretel

TECHNICAL GUIDE to access Business Talk IP SIP IPBX Shoretel TECHNICAL GUIDE to access Business Talk IP SIP IPBX Shoretel versions addressed in this guide : 14.2 Information included in this document is dedicated to customer equipment (IPBX, TOIP ecosystems) connection

More information

SHORETEL APPLICATION NOTE

SHORETEL APPLICATION NOTE SHORETEL APPLICATION NOTE for IntelePeer SIP Trunking Date: August 26, 2016 App Note Number: For use with: Product: System: TC-16056 IntelePeer SIP Trunking ShoreTel Connect ONSITE ShoreTel Connect ONSITE

More information

Application Notes for Packet One SIP Trunk System Version 3.1 Interoperability with Avaya Software Communication System Release Issue 1.

Application Notes for Packet One SIP Trunk System Version 3.1 Interoperability with Avaya Software Communication System Release Issue 1. Avaya Solution & Interoperability Test Lab Application Notes for Packet One SIP Trunk System Version 3.1 Interoperability with Avaya Software Communication System Release 4.0 - Issue 1.0 Abstract These

More information

Connecting PBX to BroadSoft's BroadCloud SIP Trunk using AudioCodes Mediant BRI/PRI Gateway

Connecting PBX to BroadSoft's BroadCloud SIP Trunk using AudioCodes Mediant BRI/PRI Gateway Quick Guide AudioCodes Mediant Series BRI/PRI Media Gateways Connecting PBX to BroadSoft's BroadCloud SIP Trunk using AudioCodes Mediant BRI/PRI Gateway Version 7.2 Introduction See Chapter 1 Obtain Software

More information

SIP Trunking using Optimum Business SIP Trunk Adaptor and the Nortel BCM50 IP-PBX (Release 5.0)- V

SIP Trunking using Optimum Business SIP Trunk Adaptor and the Nortel BCM50 IP-PBX (Release 5.0)- V NORTEL SIP Trunking using Optimum Business SIP Trunk Adaptor and the Nortel BCM50 IP-PBX (Release 5.0)- V9.0.1.74.660 Goal The purpose of this configuration guide is to describe the steps needed to configure

More information

Cisco Unified IP Phone Settings

Cisco Unified IP Phone Settings Phone Settings Overview, page 1 Cisco Unified IP Phones 7906G and 7911G Menus, page 1 Phone Setup s, page 4 Network Configuration Menu, page 5 Device Configuration Menu, page 17 Security Configuration

More information

Application Notes for MultiTech FaxFinder IP with Avaya IP Office Issue 1.0

Application Notes for MultiTech FaxFinder IP with Avaya IP Office Issue 1.0 Avaya Solution & Interoperability Test Lab Application Notes for MultiTech FaxFinder IP with Avaya IP Office Issue 1.0 Abstract These Application Notes describe the configuration steps required to integrate

More information

Grandstream IP Phone Configuration Guides

Grandstream IP Phone Configuration Guides Grandstream IP Phone Configuration Guides Version 1.0 Yeastar Information Technology Co. Ltd. Table of Contents FOR GRANDSTREAM GXP SERIES... 3 Register with MyPBX... 3 Provisioning for MyPBX... 5 Phone

More information

Protocol & Port Information for the deployment of. and. within IP Networks

Protocol & Port Information for the deployment of. and. within IP Networks Protocol & Port Information for the deployment of and within IP Networks SpliceCom Ltd The Hall Business Centre Berry Lane Chorleywood Herts WD3 5EX Phone: 01923-287700 Fax: 01923-287722 E-mail: info@splicecom.com

More information

Technical Note FLX UC 1000/1500 Registering with Shoretel ShoreGear

Technical Note FLX UC 1000/1500 Registering with Shoretel ShoreGear FLX UC 1000/1500 Registering with Shoretel ShoreGear Date: February 14, 2017 This technical note gives a detailed description on how to register a Revolabs FLX UC 1000/1500 IP & USB conference phone with

More information

Dolby Conference Phone. Configuration Guide for Unify OpenScape Enterprise Express 8.0.x

Dolby Conference Phone. Configuration Guide for Unify OpenScape Enterprise Express 8.0.x Dolby Conference Phone Configuration Guide for Unify OpenScape Enterprise Express 8.0.x Version 3.3 31 July 2017 Copyright 2017 Dolby Laboratories. All rights reserved. Dolby Laboratories, Inc. 1275 Market

More information

Dolby Conference Phone. Configuration Guide for Microsoft Skype for Business

Dolby Conference Phone. Configuration Guide for Microsoft Skype for Business Dolby Conference Phone Configuration Guide for Microsoft Skype for Business Version 3.3 31 July 2017 Copyright 2017 Dolby Laboratories. All rights reserved. Dolby Laboratories, Inc. 1275 Market Street

More information

Abstract. Innovation Network App Note

Abstract. Innovation Network App Note Innovation Network App Note IN-14003 Date: January 2014 Product: Grandstream HandyTone and Enterprise Analog Gateways System version: ShoreTel 14.1 Abstract This application note provides the details on

More information

Dolby Conference Phone. Configuration guide for Cisco Unified Communications Manager

Dolby Conference Phone. Configuration guide for Cisco Unified Communications Manager Dolby Conference Phone Configuration guide for Cisco Unified Communications Manager Version 3.1 22 February 2017 Copyright 2017 Dolby Laboratories. All rights reserved. Dolby Laboratories, Inc. 1275 Market

More information

RP-FSO522 2-Line FXO, 2-Line FXS SIP IP Gateway. Feature

RP-FSO522 2-Line FXO, 2-Line FXS SIP IP Gateway. Feature RP-FSO522 2-Line FXO, 2-Line FXS SIP IP Gateway RP-FSO522 is an 2-Line FXO plus 2-Line FXS gateway with SIP protocol IP device which allows to connect 2 Lines of analog PSTN telephone line and connect

More information

Business Communication Manager Release 5.0 Configuration Guide for Skype for SIP R1.3. Issue 1.0

Business Communication Manager Release 5.0 Configuration Guide for Skype for SIP R1.3. Issue 1.0 Avaya BCM Solutions Test Lab Business Communication Manager Release 5.0 Configuration Guide for Skype for SIP R1.3 Issue 1.0 Abstract This document provides guidelines for configuring a SIP Trunk between

More information