Spectrum Enterprise SIP Trunking Service Zultys MX Phone System v9.0.4 IP PBX Configuration Guide

Transcription

1 Spectrum Enterprise SIP Trunking Service Zultys MX Phne System v9.0.4 IP PBX Cnfiguratin Guide Abut Spectrum Enterprise: Spectrum Enterprise is a divisin f Charter Cmmunicatins fllwing a merger with Time Warner Cable and acquisitin f Bright Huse Netwrks. Spectrum Enterprise is a natinal prvider f scalable, fiber technlgy slutins. The Spectrum Enterprise prtfli includes netwrking and managed services slutins, including Internet access, Ethernet and Managed Netwrk Services, Vice, TV and Clud slutins. Our industry-leading team f experts wrks clsely with clients t achieve greater business success. Abut this dcument: Spectrum Enterprise assures IP PBX cmpatibility by cnducting interperability testing t ensure any ptential cmpatibility issues have been reslved prir t installatin. Please review the IP PBX cnfiguratin instructins in this guide prir t yur installatin date. Be advised that this dcument may cntain references t Time Warner Cable Business Class. All references t Time Warner Cable Business Class, TWCBC r TWC shuld be read as Spectrum Enterprise. Thank yu, Spectrum Enterprise 2017 Charter Cmmunicatins. All Rights Reserved. Nt all prducts, pricing and services are available in all areas. Pricing and actual speeds may vary. Restrictins may apply. Subject t change withut ntice. Last Update:

2 Technical Publicatins Octber 14 Time Warner ITSP Setup Guide Authr: Zultys Technical Supprt This cnfiguratin guide was created t assist knwledgeable vendrs with cnfiguring the Zultys MX Phne System with Time Warner SIP Trunks using Innmedia ESBC B Ver OR, Innmedia ESBC 10K-MDX Ver OR ITSP service. The Zultys MX must be running fr prper peratin. Questins abut sftware installatin r ther PBX cnfiguratin issues shuld be directed t Zultys supprt at supprt@zultys.cm. The Zultys Phne System Manual is available n the Zultys KBS: NOTE: in this dcument all IP addresses are example IP addresses, please replace with a valid IP f yur MX Z u l t y s, I n c L u c e r n e S u n n y v a l e, C a l i f r n i a, U S A w w w. z u l t y s. c m

3 Cntent Technical Publicatins 1. CREATE CUSTOM CODEC PROFILE PANEL CONTENTS CREATING OR EDITING A PROFILE MODIFYING PROFILE PARAMETERS BUTTON BAR CREATE ITSP ACCOUNT SERVERS TABLE PROPERTIES TABLE CONFIGURE THE ACCOUNT AUTHENTICATION TABLE PARAMETERS EDITING THE TABLE ENABLING ALG / SBC ON MX (MX VERSION 5.0+) NETWORKS RTP MAPPING ALTERNATE SETUP ALTERNATE CALLER ID SETUP REQUIREMENTS GENERAL MXNETWORK Create Custm Cdec Prfile This carrier nly supprts G711 which requires the MX t nly ffer G711 in its SDP packets. This will require a new custm cdec prfile t be created. In the MX Administratin click Prvisin Cdec, then click n the Cdec prfiles tab, and then click the New buttn. Time Warner ITSP Setup Guide ( ) / Revisin 7 Octber 16, Zultys, Inc. N reprductin f distributin withut permissin Page 2 f 15

4 Technical Publicatins In the resulting Pp Up, prvide a descriptive name fr the new cdec prfile, such as 711Only, and frm the list f available cdec select ONLY G.711 U-law, and click OK. The Cdec Prfile Editr, as shwn abve, creates and edits Cdec Prfiles. Yu access the Cdec Prfile Editr by pressing the New r Edit buttn in the Cdec Prfiles windw. 1.1 Panel Cntents The Prfile data entry bx at the tp f the panel lists the name f the cdec prfile that yu are editing. G711 is the name entered in this field. The Available Cdecs table n the left side f the panel lists the cdecs that are available and are nt included in the current cdec Time Warner ITSP Setup Guide ( ) / Revisin 7 Octber 16, Zultys, Inc. N reprductin f distributin withut permissin Page 3 f 15

5 Technical Publicatins prfile. The Selected Cdecs table n the right side f the panel lists the cdecs that are included in the current cdec prfile. 1.2 Creating r Editing a Prfile T create a prfile, enter the name f a new prfile in the Prfile data entry bx at the tp f the panel. If yu enter this panel by pressing the New buttn in the Cdec Prfiles windw, this field is blank until yu enter a name. T edit a prfile, enter the name f an existing prfile in the Prfile data entry bx. If yu enter this panel by pressing the Edit buttn in the Cdec Prfiles windw, the name f the highlighted prfile in that panel is placed in the Prfile data entry bx. 1.3 Mdifying Prfile Parameters T add cdecs t the current prfile, select ne r mre cdecs in the Available Cdecs table with yur muse cursr and press the Add buttn between the tables. T remve cdecs frm the current prfile, select ne r mre cdecs in the Selected Cdecs table with yur muse cursr and press the Remve buttn between the tables. T change the rder in which cdecs are presented t ther SIP devices when negtiating cmmunicatin parameters, select the cdec in the Selected Cdecs table and press the Mve Up r Mve Dwn buttns belw the table. T rename a prfile, enter the new name fr the prfile in the Prfile data entry bx at the tp f the panel Buttn Bar OK: Pressing the OK buttn clses the Cdec Prfile Editr and places the changes in the Cdec Prfiles windw. These changes are then permanently saved t the database nly after yu press the Apply buttn in the Cdec Prfiles windw. An inactive OK buttn (buttn cntents are grey) indicates that yu have nt altered the selected prfile. Cancel: Pressing this buttn discards changes made within the data entry frm and returns yu t the Cdec Prfiles windw. 2. Create ITSP Accunt In the MX Administratr, g t Prvisin then SIP Servers and ITSPs. Time Warner ITSP Setup Guide ( ) / Revisin 7 Octber 16, Zultys, Inc. N reprductin f distributin withut permissin Page 4 f 15

6 Technical Publicatins This will bring up the SIP and ITSP cnfiguratin screen. It has three tabs alng the tp. T cnfigure the SIP server, click n the SIP tab. Fr ITSPs, click n the ITSP tab. T set up the authenticatins, click n the last tab, Authenticatin. The SIP Servers and ITSPs tabs are bth divided int tw sectins: Time Warner ITSP Setup Guide ( ) / Revisin 7 Octber 16, Zultys, Inc. N reprductin f distributin withut permissin Page 5 f 15

7 Technical Publicatins The Servers Table, lcated n the left, lists the servers that prvide vice sessin access t MX devices. The Prperties Table, lcated n the right, cnfigures the address used t access the servers and specifies transmissin characteristics f SIP packets that set up the vice sessins. 2.1 Servers Table The Servers table in the SIP Servers and ITSPs tab lists the SIP servers accessed by the MX t establish vice call sessins. Each rw crrespnds t a SIP server. The fllwing parameters identify the characteristics f each SIP server. Name: This parameter identifies the SIP Server t the MX. Other UI windws, such as the Dial Plan: Ruting panel, reference SIP Servers by their names. Active: This parameter specifies the active status between the MX and the SIP server. If this parameter is nt selected, the MX cannt use the specified SIP server t rute a call. Type: This parameter specifies hw incming calls frm the SIP server are handled by the MX. Valid parameter settings include: Internal: The number specified in the SIP INVITE is treated as a dialing pattern that is evaluated by the Ruting panel f the Dial Plan windw. External: The number specified in the SIP INVITE is treated as a DID and ruted t the user that is assigned t that number. Calls with unrecgnized DID numbers are handled as specified by the Outside panel f the Dial Plan. All servers in the ITSP panel are external. This parameter is nt listed in the Servers table f the ITSP panel. Cdec Prfile: Specifies the list f cdecs that the SIP server can use fr negtiating cmmunicatin settings with ther SIP devices. Cdec Prfiles cnfigured in yur system are listed in the Cdec Prfiles windw. SIP Prfile: SIP prfiles define SIP packet characteristics fr packets utilizing the specified SIP server. Click the SIP Prfiles buttn lcated at the bttm f the panel fr a list f SIP Prfiles and their definitins. T add a SIP Server t the table, right-click the muse while pinting at the table and select New. Enter the server parameters in the new rw. T edit an existing SIP Server, duble-click in the apprpriate cell and enter the new infrmatin. T remve a SIP Server frm the table, select the server, right-click the muse, and select Delete frm the menu. Time Warner ITSP Setup Guide ( ) / Revisin 7 Octber 16, Zultys, Inc. N reprductin f distributin withut permissin Page 6 f 15

8 2.2 Prperties Table Technical Publicatins The prperties Table defines cnnectin, registratin, and SIP packet characteristics fr the SIP server highlighted in the Servers Table. The text at the tp f the table, abve the Servers List, identifies the server cnfigured by the Prperties Table. Servers List: This table sectin defines the access address f the selected SIP Server: Request using DNS_SRV: Select this ptin t specify an FQDN that is assciated with the SIP server. The MX uses the DNS server t reslve the IP address and prt f the server. Use the fllwing servers: Select this ptin t specify ne r mre SIP Server addresses (using dtted decimal ntatin r FQDN) and prt number cnfiguratins thrugh which the MX perfrms vice calls. T add server addresses t the table, pint the cursr at the table and right-click the muse. Registratin: This sectin specifies the registratin parameters that allw the MX t register as a client t the selected SIP server. Register: Check this bx t enable the MX t register as a client t the specified SIP Server. User Name: If the Registratin ptin is enabled, this parameter specifies the string that is designated as the user name in the Frm field fr INVITE packets sent frm the MX t the SIP Server. The Frm field derives the Dmain name n the basis f the Dmain in Frm Header parameter. Timeut: If the Registratin ptin is enabled, this parameter specifies the registratin perid fr the MX. Frce Symmetric NAT Transversal: This field regulates hw RFC3581"An Extensin t the Sessin Initiatin Prtcl (SIP) fr Symmetric Respnse Ruting" is used. There are three pssible ptins fr this field: Off: RFC3581 defined behavir is disabled. On: The MX always enfrces RFC3581 when cmmunicating t this ITSP. OPTIONS SIP message is used t maintain NAT binding. Aut: The MX attempts t determine via rprt parameter if it is behind the NAT and if s enfrces NAT binding using OPTIONS SIP message. With the intrductin f SBC in versin sftware and later, it is recmmended nt t use this cnfiguratin ptin. Dmain in "Frm" Header: Fr INVITE messages that are sent frm the MX thrugh the SIP Server, this parameter specifies the display name and URL that is placed in the Frm Header: Time Warner ITSP Setup Guide ( ) / Revisin 7 Octber 16, Zultys, Inc. N reprductin f distributin withut permissin Page 7 f 15

9 Technical Publicatins Select Use Address f the MX t designate the MX as the riginatr address. Select Change t MX Dmain if device belngs t a user, t specify the MX as the riginatr address when the MX receives the message frm an MX User. If the message is received frm an unknwn user (fr example, a message may be received frm an external surce thrugh the SIP server), the MX des nt alter the Frm header. Select Use Address f the Server t specify the SIP server as the riginatr address. Select Use the Fllwing Address and then enter an IP address, t specify anther unrelated address as the riginatr address. Dmain in "T" Header: Fr INVITE messages that are sent frm the MX thrugh the SIP Server, this parameter specifies the display name and URL that is placed in the T Header: Select Use the dmain name fr the apprpriate server in the Servers List t designate the dmain name f the ITSP as the destinatin address. Select Use reslved address fr the apprpriate server in the Servers List t designate the IP address reslved frm the dmain name f the ITSP as the destinatin address. Select Use custm dmain name and then enter a dmain name, t specify anther unrelated dmain name as the destinatin address. Request-URI: Fr INVITE messages that are sent frm the MX thrugh the SIP Server, this parameter specifies the Request URI that is placed in the Request-URI: Select FQDN t designate the dmain name f the MX as the Request- URI address. Select IP Address t designate the IP address f the MX as the Request-URI address. Select Use custm dmain name and then enter a dmain name, t specify anther unrelated dmain name as the Request-URI address. Caller ID: Sets caller ID ptins prvided by the MX FROM Header Registratin User Name: Ppulate the Caller ID as the Registratin User Name Originating party Caller ID: Ppulate Caller ID as the Originating Party Caller ID Time Warner ITSP Setup Guide ( ) / Revisin 7 Octber 16, Zultys, Inc. N reprductin f distributin withut permissin Page 8 f 15

10 Technical Publicatins Custm: Ppulate Caller ID with the custm value entered Include ptinal identity header: Select P-Asserted-Identity: t ppulate the P-Asserted Identity field with the fllwing prperty Registratin User Name: Ppulate the Caller ID as the Registratin User Name Originating party Caller ID: Ppulate Caller ID as the Originating Party Caller ID Custm: Ppulate Caller ID with the custm value entered Remte Party ID: t ppulate the Remte Party ID field with the fllwing prperty Misc: Cntains miscellaneus settings Registratin User Name: Ppulate the Caller ID as the Registratin User Name Originating party Caller ID: Ppulate Caller ID as the Originating Party Caller ID Custm: Ppulate Caller ID with the custm value entered Select Ignre Dmain in Frm/T SIP headers t have the MX ignre the dmain received frm the ITSP n all packets. Select unsupprted media type respnse cde t send t the ITSP when an unsupprted media type is received frm the ITSP. Optins are 415 r Cnfigure the accunt Enter the fllwing infrmatin: Name: TimeWarner Active: Check Cdec Prfile: Select 711Only (Custmer prfile created earlier) SIP Prfile: Select Default Vide Cdec: Select Nne Use the fllwing servers: Prvided by the Carrier Prt: 5060 Register: Checked Username: Prvided by the Carrier Time Warner ITSP Setup Guide ( ) / Revisin 7 Octber 16, Zultys, Inc. N reprductin f distributin withut permissin Page 9 f 15

11 Technical Publicatins Frce Symmetric NAT Transversal: Aut Frm header: Select Use the fllwing Address: IP Prvided by Carrier T header: Select Use custm dmain name: IP Prvided by Carrier Request-URI: Select IP Address Caller ID: Select Registratin User Name An alternate methd is described in Alternate Caller ID Setup belw where Custm set t ne f their DID s Misc: Nthing selected Time Warner ITSP Setup Guide ( ) / Revisin 7 Octber 16, Zultys, Inc. N reprductin f distributin withut permissin Page 10 f 15

12 Technical Publicatins 4. Authenticatin The authenticatin tab is used t define the authenticatin infrmatin fr realm based authenticatin. Time Warner ITSP Setup Guide ( ) / Revisin 7 Octber 16, Zultys, Inc. N reprductin f distributin withut permissin Page 11 f 15

13 Technical Publicatins Realm Dmain: Prvided by Carrier User Name: Prvided by Carrier Passwrd: Prvided by Carrier 4.1 Table Parameters Each rw crrespnds t a Prtectin Dmain that the MX is allwed t access. Realm: This parameter specifies the dmain name f the realm. It must match the dmain that is ffering the challenge. User Name: This parameter specifies the User Name under which the MX is allwed t access the realm. Passwrd: This parameter specifies the passwrd that the MX uses t authenticate itself with the realm. 4.2 Editing the Table T add t a realm, access the Realm panel by right-clicking in the table and selecting Add. T edit a realm, access the Realm panel by duble-clicking in ne f the Realm entry s cells r select a Realm, right-click the muse, and select Edit. T remve a realm frm the table, select the realm, right-click the muse, and select Delete frm the menu. 5. Enabling ALG / SBC n MX (MX versin 5.0+) ALG was replaced / imprved in MX versin 5.0 by SBC. Fr full details n SBC please refer t the SBC dcument available frm the KBS: 998&fdwn=SBC.pdf r frm Technical Supprt dcument titled sbc.pdf, dcument number Nte: SBC nly needs t be enabled if yu are deplying yur MX behind a firewall. If yur MX is directly cnnected t the internet using the WAN r Ethernet 2 this sectin can be skipped. Time Warner ITSP Setup Guide ( ) / Revisin 7 Octber 16, Zultys, Inc. N reprductin f distributin withut permissin Page 12 f 15

14 Technical Publicatins In the example in the screensht belw: Netwrk /24 is the private side (LAN) f the MX. This is where all the lcal phnes are cnnected t the MX. Netwrk /0 is mapping all ther netwrks t the public side f the MX, thus perfrming the SBC functins t crrect all RTP packets by inserting the public IP listed in the Public IP field, and the External SIP prt with the prt listed in the External SIP Prt field. Sessin Brder Cntrller RTP Prt Range is the prt range that the sessin brder cntrller will use t send and receive vice packets. External RTP Prt Range is the prt range that is frwarded by the edge firewall t the MX, this prt range is independent f the Sessin Brder Cntrller RTP Prt Range (in the example belw, they were made t be the same). 5.1 Netwrks T cnfigure SBC in the rute, enable prt mapping, and assign the Public IP and prts in the fields circled in the screensht abve. If yu are nt using SBC and have the MX in ruting mde with public IPs assigned t interface 2/WAN, d nt check the Prt Mapping bx. 5.2 RTP Mapping Check each netwrk fr the MX t perfrm ALG/SBC mdificatins fr. RTP mapping must be dne if using SBC r if yur MX is directly cnnected t the internet. The /0 rute must be checked fr all netwrks as seen belw. Time Warner ITSP Setup Guide ( ) / Revisin 7 Octber 16, Zultys, Inc. N reprductin f distributin withut permissin Page 13 f 15

15 Technical Publicatins 6. Alternate Setup 6.1 Alternate Caller ID Setup Caller ID can be set t Custm with a DID belnging t the custmer. 7. Requirements 7.1 General The MX must be running r better t ensure prper functinality. P-Asserted Identity is nt supprted. Only G711 is supprted by the carrier, a custm cdec prfile must be created. 7.2 MXnetwrk When the deplyment includes a MXnetwrk, yu will need t mdify the cdecs used between ndes. This is accmplished by setting the cdec prfile applied t calls within the same lcatin as well as between lcatins t the previusly created custm cdec prfile. Time Warner ITSP Setup Guide ( ) / Revisin 7 Octber 16, Zultys, Inc. N reprductin f distributin withut permissin Page 14 f 15

16 Technical Publicatins The parameters that are set in the Cdecs panel include: Within the same lcatin use: This parameter determines the cdec prfile fr vice calls between SIP devices at the same lcatin. Between lcatins use: This parameter determines the cdec prfile fr vice calls between SIP devices that are at different lcatins. Exceptins: This table determines the cdec prfiles fr vice calls between SIP devices that are in tw specific lcatins. Cdec prfile settings in this table verride the default settings in the upper part f the panel. T add an exceptin t the table, pint the cursr in the table, right click yur muse, and select Add Exceptin. The Lcatin 1 and Lcatin 2 ptins are Lcatin names, as cnfigured n the Lcatins windw. Imprtant: Cdec panel changes d nt take effect until yu press the Apply buttn. If yu press the Cancel buttn befre pressing Apply, all pending changes t the Cdec panel and the Cdec Prfile panel are disregarded. Pressing the Apply buttn saves all pending changes all Cdec Prfile panels. Time Warner ITSP Setup Guide ( ) / Revisin 7 Octber 16, Zultys, Inc. N reprductin f distributin withut permissin Page 15 f 15