NEW! ZERO-UP. Control Flexibility for Worldwide Applications 200W/400W/800W. Built-in RS232 & RS485 Interface with GPIB optional.

Transcription

1 NEW! ZERO-UP 200W/400W/800W Programmable DC Power Supplies Built-in RS232 & Interface with GPIB optional. Constant Voltage/Constant Current Built-in RS232 & Interface An embedded Microprocessor controller Digital Encoder Knob Software Calibration Last Setting Memory Parallel Operation (Master/Slave) Active Current Sharing External Voltage or Resistance Programming Voltage up to 20V, Current up to 32A Active Power Factor Correction: 99% 85~265Vac Universal Input Voltage 9" Rack Mounted ATE and OEM Worldwide Safety Agency Approvals CE Mark for LVD and EMC Regulation C US LISTED TESTING EQUIPMENT 65SA.. TUV Rheinland.. geprufte Sicherheit Control Flexibility for Worldwide Applications

2 Product Line Up Output Output Output Model Voltage Current Power ( VDC ) ( A ) ( W ) ZUP ~ ZUP ~ 6 VDC 0 ~ ZUP ~ ZUP ~ ZUP ~ 0VDC 0 ~ ZUP ~ ZUP ~ ZUP ~ 20VDC 0 ~ ZUP ~ ZUP ~ 6 26 ZUP ~ 36VDC 0 ~ ZUP ~ ZUP ~ ZUP ~ 60VDC 0 ~ ZUP ~ ZUP ~ 80VDC 0 ~ ZUP ~ 5400 ZUP ~ 20VDC 0 ~.8 26 ZUP ~ Power Supply Identification / Accessories ZUP 36-2 / Series Name NEW NEW NEW NEW Output Voltage ( 0 ~ 36V ) Output Current ( 0 ~ 2A ) Front Panel L. Output Jacks BLANK: Standard AC Cable E. Europe U. USA O. Unterminated I: SI 32 std. BLANK: None Serial Link Cable W. Cable included BLANK: None Front Panel 3 5 Rear Panel Digital Voltmeter 2. Digital Amperemeter 3. Constant Voltage Mode Indicator 4. Constant Current Mode Indicator 5. Voltage/Current, OVP/UVP, Address Adjust 6. Alarm ( OVP, OTP, FOLD ) 7. Output ON/OFF Control 8. Local/Remote Select 9. Foldback Protection Control 0. AC Power Switch. Voltage/Current Mode Control 2. Overvoltage/Undervoltage Setting 3. Address Setting IEC320 AC Input Connectors 2. Remote IN Programming via RS232/ Remote OUT Via Communications Chaining Power Supplies to Serial Communication Bus. 4. External Analog Programing Control Connector 5. Output Bus Bars (6V to 60V) model shown. 80V to 20V models PHOENIX: PSC Plug Connectors 6. Ground Thread

3 ZUP Configurations BENCH TOP POWER SUPPLY Single Parallel ( Master / Slave ) PARALLEL OPERATION Master - Slave method: Active current sharing up to 5 units. REMOTE PROGRAMMING VIA RS232 Up. to 3 ZUP units can be controlled via RS232 interface. RS232 ZUP () ZUP (2) ZUP (3) 000m max. 0m max. Linking ZUP units with RS232 control. REMOTE PROGRAMMING VIA Up to 3 ZUP units can be controlled via interface. For operation environments that require high noise immunity or long distance communication, it is recommended to use the built- in interface. ZUP () ZUP (2) ZUP (3) 000m max. Linking ZUP units with control. 2

4 Remote Programming Via GPIB. GPIB CONTROLLER The GP485 is a high performance serial to GPIB Interface It enables a ZUP series with port to be a Talker, Listener, or controller on the GPIB * Controls up to 3 ZUP units through a single GPIB address. * Conforms to all versions of the IEEE488 standard, including IEEE GPIB BUS GP485 ( ) ZUP ( ) ZUP (3) * 9 racking possibility. * Application software - LabView, LabWindows. GP485 ( 2 ) ZUP ( ) ZUP (3) GP485 (4 ) ZUP ( ) ZUP (3) Rack Mounted ATE and OEM up to 2.4KW Six units can be assembled into 9-inch rack / 3U high to meet your configuration requirements Power Modules Table Module Type 0 ~ 6V 0 ~ 0V 0 ~ 20V 0 ~ 36V 0 ~ 60V 0 ~ 80V 200W 33A 20A 0A 6A 3.5A 2.5A 400W 66A 40A 20A 2A 7A 5A 800W 32A 80A 40A 24A 4A 0 ~ 20V 9"rack width.8a / 6 width 3.6A / 6 width 2 / 6 width 3

5 Zup Series Specifications MODEL OUTPUT VOLTAGE ( *) V OUTPUT CURRENT ( *2) A RATED OUTPUT POWER W CONSTANT LOAD REGULATION - VOLTAGE LINE REGULATION - RMS RIPPLE (5Hz-MHz Bandwidth) mv RIPPLE (pk to pk) (20MHz Bandwidth) mv RECOVERY TIME ( *3) ms TEMPERATURE COEFFICIENT - TEMPERATURE DRIFT - UP PROGRAMMING RESPONSE TIME (*4) ms DOWN PROGRAMMING FULL LOAD ms RESPONSE TIME NO LOAD ms CONSTANT LOAD REGULATION ( *5) - CURRENT LINE REGULATION ( *6) - RMS RIPPLE (5Hz-MHz Bandwidth) ma TEMPERATURE COEFICIENT - TEMPERATURE DRIFT ( *8) - PROGRAMMING ( *9) RESOLUTION - VOLTAGE ACCURACY - RESOLUTION - CURRENT ACCURACY - OVERVOLTAGE PROTECTION ( *0) V HOLD-UP TIME - DISPLAY VOLTAGE - CURRENT - STATUS - OUTPUT PROTECTIONS - INPUT INPUT VOLTAGE ( *) - INPUT CURRENT ( *2 ) A INRUSH CURRENT ( 00/200V ) A EFFICIENCY ( *2 ) % INPUT CURRENT HARMONICS - POWER FACTOR (TYP) - ENVIRONMENT OPERATING TEMPERATURE - OPERATING HUMIDITY - STORAGE TEMPERATURE - STORAGE HUMIDITY - MECHANICAL VIBRATION - SHOCK - WEIGHT Kg SIZE (WxHxD) mm EXTERNAL CONTROL OUTPUT ON/OFF - FUNCTIONS OUTPUT GOOD - OUTPUT VOLTAGE PROGRAMMING - OUTPUT CURRENT PROGRAMMING - REMOTE SENSING - COMMUNICATION INTERFACE - APPROVALS SAFETY STANDARDS - EMC STANDARDS - CONDUCTED EMI - RADIATED EMI - SERIES OPERATION - PARALLEL OPERATION - COOLING - WITHSTAND VOLTAGE - ISOLATION RESISTANCE - ZUP6-33 ZUP6-66 ZUP6-32 ZUP0-20 ZUP0-40 ZUP0-80 ZUP %+2mV From No load to Full load, constant input voltage %+mV From 85-32VAC or VAC, constant load ppm/ C from rated voltage following 30-minute warm-up. 0.0%+2mV Change in output over 8-hour interval under constant line, load and ambient temp followin %+5mA 0.0%+5mA 0.07%+0mA 0.0%+5mA 0.0%+5mA 0.07%+0mA 0.0%+5mA 0.0%+2mA 0.0%+2mA 0.0%+5mA 0.0%+2mA 0.0%+2mA 0.0%+5mA 0.0%+2mA ppm/ C from rated current following 30-minute warm-up. 0.02%+5mA 0.02%+5mA 0.05%+0mA 0.02%+5mA 0.02%+5mA 0.05%+0mA 0.02%+5mA Better than 0.028% of rated output voltage 0.02%+5mV 0.02%+8mV Better than 0.03% of rated output current 0.4%+40mA mS At 00V/200VAC, rated output voltage and output current. 3 digits ( 6v; 20v; 36v; 60v; 80v); 3.5 digits ( 0v; 20v ) accuracy: 0.2% +/- 2 digits. 3.5 digits (32A); All others 3 digits, accuracy: 0.5% +/- 3 digits. CV/CC, Alarm, Fold, Local/Remote, On/Off. Over Voltage, Over Temperature, Foldback Vac Continuous, 47-63Hz 3.0/.5 5.6/2.7.2/ /.4 5.6/2.7.2/ /.4 5/30 (*7) /30 (*7) /30 (*7) 69/72 74/77 74/77 73/77 79/82 77/8 74/78 Complies with EN , Class A 0.99 at 00/200Vac, 00% load. 0 to 50 C ; 00% Load % RH ( No dewdrop ). -20 to 70 C 0-95% RH (No dewdrop). 0-55Hz, Amplitude (sweep min ) 2G, X, Y, Z, When mounted with mounting screws. Less than 20G W and 400W units: 70 x 24 x W units: 40 x 24 x 350 (Refer to outline drawing) By TTL Signal or Dry Contact (Refer to instruction manual). Open collector (Refer to instruction manual). By Voltage ( 0-4V ) or by Resistance ( 0-4K ) (Refer to instruction manual). By Voltage ( 0-4V ) or by Resistance ( 0-4K ) (Refer to instruction manual). Maximum 0.5V drop on each load wire for model up to 60V and 2V for the 80V, 20V models RS232 and Built-in, IEEE488 Optional. UL3-, EN600- EN6326-, IEC 6326-, FCC part 5 (class A). EN55022-B, FCC-B, VCCI-2 EN55022-A, FCC-A, VCCI- Up to 2 units (Refer to instruction manual). Master - Slave method; up to 5 units (Refer to instruction manual). Forced air by blower fan (Blower fan is mounted within unit). Input - Chassis...2.0kVAC min, Input - Output...3.0kVac min, Output - GND...500VAC min. More than 00MOhm at 25 C and 70% R.H. NOTES: *. Minimum voltage is guaranteed to maximum 0.2% of the rated output voltage. *2. Minimum current is guaranteed to maximum 0.4% of the rated output current. *3. Time for recovery to within +/-50mV against current change of 50% to 00%. *4. From zero volts to full scale, resistive load and current setting at maximum. *5. From no load to full load, constant input voltage. *6. From 85~32Vac or 70~265Vac constant load. *7. At cold start Ta=25 C. 4 *8. Change in output over 8 hour interval constant line, load and ambient temperature following 30-minutes warm-up. *9. Given for control of the output via the serial communication or via front panel controls. *0. Inverter shut down method, manual reset (OVP will shut down output) *. For cases where conformance to various safety specs. (UL, IEC, etc.) are required, to be described as VAC (50/60Hz) on name plate. *2. At 00V/200V and Maximum Output Power.

6 ZUP20-20 ZUP20-40 ZUP36-6 ZUP36-2 ZUP36-24 ZUP ZUP60-7 ZUP60-4 ZUP ZUP80-5 ZUP20-.8 ZUP %+4mV 0.005%+2mV g 30-minute warm-up %+5mA 0.07%+0mA 0.0%+5mA 0.0%+5mA 0.07%+0mA 0.0%+5mA 0.0%+5mA 0.07%+0mA 0.0%+5mA 0.0%+5mA 0.0%+5mA 0.0%+5mA 0.0%+2mA 0.0%+5mA 0.0%+2mA 0.0%+2mA 0.0%+5mA 0.0%+2mA 0.0%+2mA 0.0%+5mA 0.0%+2mA 0.0%+2mA 0.0%+2mA 0.0%+2mA %+5mA 0.05%+0mA 0.02%+5mA 0.02%+5mA 0.05%+0mA 0.02%+5mA 0.02%+5mA 0.05%+0mA 0.02%+5mA 0.02%+5mA 0.02%+5mA 0.02%+5mA 0.02%+2mV 0.02%+20mV 0.02%+35mV 0.02%+50mV 0.02%+80mV /2.7.2/ /.4 5.6/2.7.2/ /.4 5.6/2.7.2/ /.3 4.9/ /.4 5.3/ /30 (*7) /30 (*7) /30 (*7) 5 5/30 (*7) 5 79/83 79/82 76/80 80/84 80/84 75/79 80/84 80/84 78/82 83/87 78/82 82/

7 GP485 SPECIFICATIONS The GP485 has all the software and logic required to implement the physical and electrical Specifications of the IEEE488 and standards Input Voltage /freq Input consuption IEEE 488 Capability Indication LED s Baud rate Address Operating temp Storage temp Conducted emission Radiated emission Safety standards EMC standards Withstand voltage Vibration Size (WxHxD) Weight 85 ~ 265Vac continuous 47 ~ 63 Hz 5W SH,AH,T6,TE0,L4,LE0,SR,RL0,PP,DC,DT0,C0,E,E2 Power /Ready,Talk,Listen,SRQ Optional 300, 600,200, 2400, 4800, 9600 Default :9600 up to 30 can be set using an address switch 0~ ~ 70 EN5022B,FCC-B EN5022A,FCC-A UL3-, EN600- EN6326-, IEC 6326-, FCC part 5 (class A). Input - Chassis 2.0kVAC min, Input - Output 3.0kVac min, Output - Chassis 500VAC min. 0-55Hz, Amplitude (sweep min ) 2G, X, Y, Z, When mounted with mounting screws. 70x24x350 (GP 485 has all the mechanical specifications & mounting hole as ZUP200W/400W units).95 Front Panel Rear Panel Power/Ready: Indicates that the power is ON and the self-test has passed successfully. The unit is ready to operate once the LED illuminates. 2. Talk: Indicates that the GP485 is addressed as a GPIB Talker. 3. Listen: Indicates that the GP485 is addressed as a GPIB Listener. 4. SRQ: Indicates that the GP485 signal line SRQ is asserted. 5. AC ON/OFF: Turns AC power On and Off.. OUT: EIA-568A shielded type connector, used for communication with ZUP power supplies. 2. GPIB: Shielded 24-pin Champ female connector, with metric screwlock. Used for GPIB communication with the GPIB controller. 3. AC Input: IEC type appliance inlet. 4. XXXXXXXXXXXX 6

8 ADDR OVP/UVP V/A FOLD REM OUT Outline Drawings ZUP 200W/400W Units + _ _ Note 30.0 External Control Connector POWER SUPPLY CV ALM +V -V V CC + _ A + _ 3.0 NEMIC-LAMBDA LTD. H POWER _ DIMENSIONS: mm 70x24x350 WEIGHT: Kg 200W units: W units: 3.2 Note:. Housing AMP: with pins AMP: Header PHOENIX: PSC,5/3-M-PE Plug PHOENIX: PSC,5/3-3-F Plastic cable housing Included with the power supply _ + _ B A A B 48.4 _+ 0.5 B A A B Mounting Holes Tap M4 x 4 marked A Rubber Bumpers 4 places marked B (removable) RS232/ communication connectors IEC320 AC Inlet Outline Drawings ZUP 800W Unit + _ _ REMOVABLE HANDLE 30.0 Note External Control Connector _ _ _ V -V Note 2 Rear Panel Output Voltage Connector For 80V, 20V Models. +V -V POWER _ _ 20.0 DIMENSIONS: 40x24x350 mm. B A A B 8.5 RS232/ communication connectors IEC320 AC Inlet WEIGHT: 5.8 kg. Note:. Housing AMP, with pins AMP, Included with the power supply. Rubber Bumpers: 4 places marked B (removable) B 8.90 _+ 0.5 A A _ 0.5 B Mounting Holes: Tap M4 x 4 marked A 7

9 Accessories. AC Cord Sets Three optional cords are possible according to order: Region North America Europe SI- 32 Std AC Cord 5A / 25Vac 0A / 250Vac 0A / 250Vac L=2m L=2m L=2m Power Supply Connector IEC320-C3 IEC320-C3 IEC320-C3 Wall Plug NEMA 5-5P INT L 7/ VII SI-32 P/N ZUP/U ZUP/E ZUP/I North America Europe SI-32 Standard 2. Communication Cable RS232/ cable is used to connect the power supply to the PC controller Mode RS232 RS232 PC connector DB-9 DB-25 DB-9 DB-25 Communication cable Shield Ground, L=m Shield Ground, L=m Shield Ground, L=m Shield Ground, L=m Power Supply Connector EIA / TIA-568A (RJ-45) EIA / TIA-568A (RJ-45) EIA / TIA-568A (RJ-45) EIA / TIA-568A (RJ-45) P/N ZUP/NC40 ZUP/NC403 ZUP/NC402 ZUP/NC404 DB-25 (female connector) DB-9 (female connector) EIA/TIA (RJ-45) 3. ZUP serial link cable Used to chain Power Supply to Power Supply from a serial communication bus Mode Communication cable Shield Ground, L=50cm Power Supply Connector Remote IN /OUT EIA /TIA -568 A (RJ-45) P/N ZUP/ W 8

10 Options ( 200W, 400W, 800W Models ). FRONT PANEL OUTPUT JACKS P/N: ZUP / L Outline Drawing: Physical Dimensions in mm. ZUP 200W/400W Units: 70x53x405.9 ZUP 800W Units: 40x53x Up to 20A output current via front panel jacks. 2. ZUP ASSEMBLIES Dual Output Packing 200W/400W models P/N: NL Max Up to six power units can be assembled into a 9, 3U rack, kit P/N NL00. In cases where the entire rack is not occupied with power units, NL0 blank panels can be installed. P/N: NL