RACK-220 CHASSIS USER S MANUAL

Transcription

1 RACK-220 CHASSIS USER S MANUAL

2 1 Copyright Notice This document and product is copyrighted, Jun 1999, by ICP Electronics Inc. All rights are reserved. No part of this manual may be reproduced, copied, or translated without prior notice to ICP Electronics Inc. The information provided in this document is for reference only. We do not assume any responsibility arising out of the application of the products. This manual is subject to change without any notice. RACK-220 and ICP are trademarks of ICP Electronics Inc.

3 2 Table of Contents Chapter 1 Product Information 1.1 General Information 1.2 Product Specifications 1.3 Dimensions Chapter 2 System Setup 2.1 Front Panel of RACK Rear Panel of RACK Removing the chassis cover 2.4 Backplane Installation 2.5 Disk Drives Installation 2.6 Replacing the Filter 2.7 Power Supply Installation 2.8 Fan Installation Appendix A Passive Backplane Appendix B Exploded Diagram

4 3. Chapter 1 Product Information 1.1 General Information RACK-220 rack-mount IPC chassis is a rugged PC/AT compatible computer designed for the factory floor and other Industrial harsh environment. The RACK-220 features 6 slots Passive Backplane and high reliability Input Standard Power Supply : ACE-920A. 1.2 Product Specifications General specification - Construction : Heavy-duty steel - Disk Driver : Supports one 3.5 FDD, one CD -ROM, and one 3.5 HDD - Cooling Fan : One ball bearing fan for add-on cards cooling - Indicator : Three LEDs to monitor the status of HDD, FAN and Power Supply - Dimension : 473 x 483 x 88 mm ( D x W x H ) Passive Backplanes (Option) BP-5SD, PCI-5SD, PCI-6SR, PCI-5SD3, PCI-5SD4, PCI-5SD5, IP-5SD, IP-5SD3 or IP-5SD5. Power Supply (Option) Standard equipped power supply for the RACK-220 is ACE-920A. It also can be equipped with other power supply such as ACE-925A, ACE-932A, ACE-935A, ACE-932T, ACE-925T, ACE-925C or ACE-916V.

5 4 Working Environment - Operating Temperature : 0~50 C - Relative Humidity : 5~95% Relative Humidity - Vibration : 5-17Hz, 0.1 double amplitude displacement Hz, 1.5G acceleration peak to peak - Shock : 10G acceleration peak to peak - Safety approval : meet CE, FCC Cooling Fan One ball bearing fan for add-on cards cooling Drive Capacity Supports one 3.5 FDD, one 3.5 HDD and one CD -ROM.

6 5 1.3 Dimensions The dimensions of RACK-220 are designated in the figure below x10(OB) UNIT:mm

7 6 Chapter 2 Installation Procedure The following set up procedure is provided to assist you in installing the system, please follow the steps below: 2.1 Front Panel of RACK-220 RACK-220 is equipped with front panel, which supports Power Switch, Reset Button, Buzzer ON/OFF Button and LEDs. FAN LED HDD LED Power LED RESET BUZZER ON/OFF

8 The Installation for Lockable Front Door Please insert the front door to the front panel as the diagrams below.

9 Control Panel of RACK-220 Please refer to the following information as you set up your system. Fan2 Fan1 HDD +5V Buzzer ON/OFF Reset Power in Connect Fan1 Connect Fan2 Connect HDD,Reset Connect Buzzer Fan2 Fan1 HDD +5V Buzzer ON/OFF Reset Power in Pin# Pin Power in HDD LED Reset Fan1 Fan2 Signal Name +5V +12V Fan 3 GND 3 Pin# Signal Name Pin# Signal Name 1 2 Sensor +12V GND HDD LED Reset HDD LED GND Reset GND

10 9 LED & Switch: U4: FAN1 sensor Red / Green LED Status Light > 1000 RPM Green < 1000 RPM Flash Red U3: FAN2 sensor Red / Green LED (Reserve) Status Light > 1000 RPM Green < 1000 RPM Flash Red Fault Detection and Alarm Notification: The RACK-220 monitors the system for a fan failure (speed too low). If any of the cooling fan fails, a corresponding LED indicator located at the front door will change color from green to red and will flash (blinking). D20: HD System HD LED D21: POWER LED SW1: RST system reset button SW2: A Buzzer is activated at the start of any malfunction and sounds until the Buzzer Push button ( SW2) is pressed. However, the alarm indicator (LED) will stay blinking until the fault condition is solved. JP3: ON OFF Enable FAN1 sensor function Disable FAN1 sensor function JP4: ON OFF Enable FAN2 sensor function Disable FAN2 sensor function

11 10 CN1: FAN1 CONNECTOR CN1 PIN# Function 1 1 Sensor pin 2 +12V 3 Ground 3 CN2: FAN2 CONNECTOR CN2 PIN# Function 1 1 Sensor pin 2 +12V 3 3 Ground CN9:POWER CONNECTOR CN9 PIN# Function V 2 +12V 3 3 Ground CN11: HDD & RESET CONNECTOR CN9 PIN# Function 1 1 HDD LED (+) 2 GND 3 System Reset 4 4 connector

12 Rear Panel of RACK-220 The following figure illustrates the rear panel for your reference. AC OUTPUT AC INPUT

13 Removing the chassis cover The cover is mounted by ten screws on the chassis, remove them and slide the cover to the rear of the chassis. Figure below shows how to remove the chassis cover. Step 2 Step 1

14 Backplane Installation Figure below illustrates how to install the backplane on the RACK-220. Step 2 Step 1 Step 3

15 Disk Drives Installation 1. Remove the chassis top cover 2. Remove the disk drive bay 3. Attach the FDD/CD-ROM to the bracket with four screws and connect FDD/CD-ROM cable & power cable to the FDD/CD-ROM. 4. Attach the HDD to the bracket with four screws and connect a 40-pin flat cable & power cable to the HDD.

16 15

17 Replacing the Filter The filter of the RACK-220 is located at the front panel of the chassis. Under continuous use, the filter should be removed about once a month. Take out the old filter and slide the new one into place. Then close and lock the filter door. Step 2 Step 1

18 Power Supply Installation Please refer to the figure below to install the Power Supply. Model Input Voltage Peak Current +5V +12V Max Output +5V +12V -5V -12V ACE-920A 85V to 265VAC 22A 7A 20A 4A 0.3A 0.5A BACKPLANE P9 P8 7 1 ACE-920A POWER SUPPLY P9 P8 POWER SWITCH Brown Brown Blue Blue White Black Black White GND 2.8 Fan Installation

19 18 Figure below illustrates how to connect the Fan and Power Supply to the Control Panel. CP-03 CONTROL PANEL CN1 CN9 ACE-920A POWER SUPPLY

20 19 APPENDIX A PASSIVE BACKPLANE PCI-5SD

21 20 APPENDIX B EXPLODED DIAGRAM