XSEDE POWER BEAMS and PANELS

Size: px
Start display at page:

Download "XSEDE POWER BEAMS and PANELS"

Transcription

1 POWER BEAMS and PANELS Table of Contents Price List Effective Dates: Revision See page Statement of Line 4.2 Power Beam Components 4.2 Power Panel Components 4.3 Screens & Frameless 4.4 Worksurfaces & Support Legs 4.5 Power & Data Components 4.6 Overview 4.7 Power Beam Components 4.8 Power Panel Components 4.12 Stability Guidelines 4.17 End and Mid Panels 4.18 Screens 4.20 Worksurfaces & Support 4.21 Integrating with Footprint & Priority Overhead Storage 4.25 Integrating with Narrate Wire Power Components 4.29 Power Beam Components 4.33 Power Panel Components 4.47 Screens 4.61 Frameless Resin & Glass 4.63 Worksurfaces 4.64 Worksurface Support 4.68 Electrical Components 4.76 Power/Data Centers 4.78 Wood 4.79 Laminate 4.80 Paint & Vinyl 4.82 Resin & Glass 4.83 Fabric 4.84 COM 4.85 Page 4.1

2 Power Beam Components Statement of Line IMPORTANT: All dimensions shown below are nominal and have been rounded to the nearest inch. Refer the appropriate pricing pages for actual dimensions. Power Beam See page 4.33 to specify. Support T-Legs See page 4.34 to specify. End Trim See page 4.34 to specify. Connectors Available in S, L, V, T, Y, and X. See pages to specify. 48"W 60"W 72"W 5"D 18"H 28"H 20"D 3"W 8"H 19"H 29"H 20"D Power Beam End Panels and Mid Panels See pages to specify. Power Beam Ceiling Poles See page 4.45 to specify. Power Beam Cable Managers See page 4.46 to specify. 28"W 34"W 51"W 63"W 49"H 133"H 3"D 9"H 19"H 3"D Page 4.2

3 Power Panel Components Statement of Line IMPORTANT: All dimensions shown below are nominal and have been rounded to the nearest inch. Refer the appropriate pricing pages for actual dimensions. Power Panel Frames See page 4.47 to specify. Support T-Legs See page 4.48 to specify. End Trim See page 4.48 to specify. Tiles Available in fabric, laminate, metal, and metal markerboard See pages to specify. Connectors Available in S, L, V, T, Y, and X. See pages 4.51 to specify. 48"W 60"W 72"W 5"D 18"H 28"H 20"D 3"W 8"H 48"W 60"W 72"W 10"H 29"H 20"D Power Panel End and Mid Panels See pages to specify. Power Panel Ceiling Poles See page 4.59 to specify. Power Panel Cable Managers See page 4.60 to specify. 28"W 34"W 51"W 63"W 49"H 133"H 3"D 9"H 19"H 3"D Page 4.3

4 Screens, Frameless Resin, & Frameless Glass For Use with and Power Panels Statement of Line IMPORTANT: All dimensions shown below are nominal and have been rounded to the nearest inch. Refer the appropriate pricing pages for actual dimensions. Center-Mount Fixed Screens See pages to specify. Center-Mount Fixed Screens with Accessory Rail(s) See page to specify. Frameless Resin and Glass See page 4.63 to specify. 48"W 60"W 72"W 20"H 30"H 48"W 60"W 72"W 20"H 30"H 48"W 60"W 72"W 14"H Page 4.4

5 Worksurfaces and Support Legs For Use with and Power Panels Statement of Line IMPORTANT: All dimensions shown below are nominal and have been rounded to the nearest inch. Refer the appropriate pricing pages for actual dimensions. Rectangular Worksurfaces See page 4.64 to specify. 120 Curved Corner See page 4.65 to specify. 30"W 36"W 42"W 48"W 54"W 60"W 66"W 72"W 78"W 84"W 24"D 30"D 48"W 24"D 30"D O-Legs See page 4.68 to specify. U-Legs See page 4.68 to specify. Undersurface Support Legs See page 4.68 to specify. Brackets See page 4.69 to specify. 27"H 24"D 30"D 27"H 24"D 30"D 27"H 2"D 27"H 2"D Page 4.5

6 Power & Data Components For Use with and Power Panels Statement of Line IMPORTANT: All dimensions shown below are nominal and have been rounded to the nearest inch. Refer the appropriate pricing pages for actual dimensions. 8-Wire Power System Components See page 4.76 to specify. Power/Data Centers See page 4.78 to specify. Cable Management and Organizational Accessories Plastic cable carrier Metal cable basket See Xsede Height Adjust chapter in the Price List. Page 4.6

7 Overview Planning Xsede offers three freestanding options to provide power, divide space, and support privacy in the workspace. Power panels can support privacy screens and worksurfaces. Power panels feature a modesty tile in four tile material choices: Fabric Laminate Metal Metal markerboard Power beams are available in two heights and accept screens in a variety of heights and material choices. Page 4.7

8 Overview Planning Xsede power beams are a UL 1286 listed, four-circuit, eight-wire system and available in two heights and three power outlet location options. Components are specified separately. Accessory rail top caps accept screens to divide space and provide privacy. Power beams are dual sided, providing power and data to users on each side. Horizontal beams are available in true widths of 48", 60", and 72." Wire trough is standard on both sides of the beam to organize cables from beam to worksurface. High power beams can support worksurfaces. End trims must be specified to finish the end of the power beam when a T- leg is used at the end of a configuration. Connectors are available in straight, L, V, T, Y, and X configurations (Tconnector is shown). Electrical jumpers, also specified separately, allow power to move from one beam to the next. T-legs are non-handed and standard with black leveling glides. Foot width is and the design matches Xsede height-adjust tables and open plan products. Voice/data openings are standard on both sides of the beam. Page 4.8

9 Power Beam Components Dual-Sided (Horizontal Structure) Planning Details Related Products Dual-sided power beam is available in three widths 48", 60", and 72". This horizontal structure is the main component used to create low and high power beam applications. Each beam model includes: Accessory rail top cap Electrical covers with power and data cutouts on each side Dual-sided double distribution block and power kit Wire trough Internal J-hooks to manage cables Two data adapter kits One Left, One Right Location Four receptacle openings; two per side Four voice/data openings; two per side Specify four duplex receptacles separately T-legs are the foundation of a power beam structure and are available in two heights. See page End panels and mid panels can replace T-legs and connectors for even more privacy between workspaces. See page "H tackable fabric screens can be attached to the accessory rail of a low beam. They are not for use on high beams or power panel due to tipping. Three power cutout locations are available: Connectors are the foundation of a power beam structure and are available in two heights. See page Center Location Four receptacle openings; two per side Four voice/data openings; two per side Specify four duplex receptacles separately Two Left, Two Right Location Eight receptacle openings; four per side Four voice/data openings; two per side Specify eight duplex receptacles separately Connections Support components are specified separately and are specific to low beam or high beam configurations. End trim is required at the end of a run supported by T-leg. Multiple beams can be connected. They can be the same width or a combination of widths and power cutout locations to create the desired length and functionality. See page 4.17 for stability guidelines. See page 4.31 for electrical jumper lengths. 20"H tackable fabric screens can be attached to the accessory rail of a high beam. Power components are specified separately. 14"H glass or resin screens can be attached to the accessory rail of a high beam. See page Page 4.9

10 Power Beam Components Support T-Legs and End Trim Planning Details Related Products Support T-legs are the foundation of the power beam structure and are available in two heights "H support T-leg is used to create low power beam applications. When combined with the dual-sided power beam, a structure with an overall height of " and a " open base is created "H support T-leg is used to create high power beam applications. When combined with the dual-sided power beam, a structure with an overall height of 29" and a " open base is created. Floor glides are standard in black and provide 1 2" of height adjustment. End trim is required for T-legs used at the end of a run to cover the internal cavity of the beam. Connections T-legs are used at the end of a run or inline to create an infinite run when maximum stability is desired. T-legs can be combined with connectors, mid-panels, and end panels to create configurations. See page 4.17 for stability guidelines. High power beams can be used to support worksurfaces. Cable managers are available to cover power in-feeds and other cables that run from the power panel to a floor or wall outlet. They clip on to the a T-leg or S-connector. They will not fit directional connectors. Cable managers are metal and available in all colors to match the surface to which they are installed " 2 3 4" 4 5 8" 7 7 8" 2 3 4" 2" 7 8" Cut-out in T-leg top allows routing jumpers and cables through the leg in beam-to-beam applications " " 2" 7 8" " " 29" " Low Beam " High Beam Page 4.10

11 Power Beam Components Connectors Planning Details Smooth Top Cap Cable Cut-Out Beam Trim Connectors enable the structure to continue in a straight line or turn a corner for a change of direction. They are available in two heights for low beam or high beam structures. Six directional types are available: S (straight, inline) L (2-way 90 ) V (2-way 120 ) T (3-way 90 ) Y (3-way 120 ) X (4-way 90 ) L-connector is used to connect two beams at a 90 angle. V-connector is used to connect two beams at a 120 angle. Y-connector is used to connect three beams at a 120 angle. X-connector is used to connect four beams at a 120 angle. Floor glides are standard in black and provide 1 3 4" of height adjustment. Post Leg Parts of L, V, T, Y, and X connectors can be specified in contrasting colors. Kimball suggests that the top cap and beam trim be specified to match the adjoining beam. Beam trim is continous on the inside and outside of L-, V-, T-, and Y-connectors; beam trim is on the inside only on X-connectors. Post legs can be specified the same color as the beam or to match T-legs, if they are a contrasting color. Connections Bolts, standard with each connector model, are used to attach the connector to the power beam. Cut-out in connector allows power jumper and data cables to be routed through the connector in power beam-to-beam applications. Cut-out can accommodate two jumpers passing through the opening. See page 4.31 for electrical jumper lengths. IMPORTANT: Jumpers should be installed through a directional connector prior to assembling the connector. Planning Factors L, V, T, Y, and X connectors will not accommodate a power entry. See page 4.17 for stability guidelines. S-connector is used to create straight, in-line applications. It consists of a post leg with a cut-out at the top like the T-leg to route jumpers and cables from beam-to-beam. It can only be specified in the middle of a run between two T-legs or with a directional connector; it cannot be used at the end of a run. T-connector is used to connect three beams at a 90 angle. Top caps are smooth, painted wood. They attach to slots in the connector. Power beam top rail design intersects with the top cap. Page 4.11

12 Power Panels Overview Planning Xsede power panels are a UL 1286 listed, four-circuit, eight-wire system and available in one height and three power outlet location options. Components are specified separately. Accessory rail top caps accept screens to divide space and provide privacy. Wire trough is standard on both sides of the horizontal beam to organize cables from beam to worksurface. Power panels are dual sided, providing power and data to users on each side. Horizontal beams are available in true widths of 48", 60", and 72." Power panels can support worksurfaces. Voice/data openings are standard on both sides of the horizontal beam. End trims must be specified to finish the end of the power panel when a T-leg is used at the end of a configuration. Connectors are available in straight, L, V, T, Y, and X configurations (Tconnector is shown). Electrical jumpers, also specified separately, allow power to move from one beam to the next. T-legs are non-handed and standard with black leveling glides. Foot width is and the design matches Xsede height-adjust tables and open plan products. Tiles are available four tile material choices: Fabric Laminate Metal Metal markerboard Page 4.12

13 Power Panel Components Dual-Sided Power Panel Frames Planning Details Dual-sided power panel frame is available in three widths 48", 60", and 72". This horizontal structure is the main component used to create power panel applications. Connections Support components are specified separately and are specific to power panel configurations. available in fabric, laminate, metal, and metal markerboard. See page Each power panel frame model includes: Accessory rail top cap Electrical covers with power and data cutouts on each side Dual-sided double distribution block and power kit Wire trough Internal J-hooks to manage cables Two data adapter kits Lower rail to support tile insert Three power cutout locations are available: One Left, One Right Location Four receptacle openings; two per side Four voice/data openings; two per side Specify four duplex receptacles separately T-legs are the foundation of a power beam structure and are available in two heights. See page End panels and mid panels can replace T-legs and connectors for even more privacy between workspaces. See page Multiple power panels can be connected. They can be the same width or a combination of widths and power cut-out locations to create the desired length and functionality. See page 4.17 for stability guidelines. See page 4.31 for electrical jumper lengths. 20"H tackable fabric screens can be attached to the accessory rail of a power panel frame. Center Location Four receptacle openings; two per side Four voice/data openings; two per side Specify four duplex receptacles separately Two Left, Two Right Location Eight receptacle openings; four per side Four voice/data openings; two per side Specify eight duplex receptacles separately Connectors are the foundation of a power panel structure. See page End trim is required at the end of a run support with a T-leg. Power components are specified separately. Power panels can be used to support worksurfaces. Related Products Tiles, specified separately, are required for power panels. They are 14"H glass or resin screens can be attached to the accessory rail of a power panel frame. See page Note: 30 H tackable fabric screens are not recommended for use on power panels due to tipping. Page 4.13

14 Power Panel Components Support T-Legs and End Trim Planning Details Connections Related Products Support T-legs are the foundation of the power panel structure. Cut-out in T-leg top allows routing jumpers and cables through the leg in beam-to-beam applications. T-legs are used at the end of a run or inline to create an infinite run when maximum stability is desired. T-legs can be combined with connectors, mid-panels, and end panels to create configurations. See page 4.17 for stability guidelines. Cable managers are available to cover power in-feeds and other cables that run from the power panel to a floor or wall outlet. They clip on to the a T-leg or S-connector. They will not fit directional connectors. Cable managers are metal and available in all colors to match the surface to which they are installed "H support T-leg is used to create high power beam applications. When combined with the dual-sided power panel frame, a structure with an overall height of " and a " open base is created. Floor glides are standard in black and provide 1 2" of height adjustment. End trim is required for T-legs used at the end of a run to cover the internal cavity of the beam. 18" 2" 4 5 8" 2 3 4" 29" 7 8" " " Page 4.14

15 Power Panel Components Tiles Planning Details Connections Planning Factors Tile should be specified the same width as the power panel frame. Two tiles must be specified for each power panel; one for each side of the frame. Tiles are required for power panels. They are "H and available in 48", 60", and 72"W. Four materials options are available: Tackable panel fabric (railroaded) Laminate Metal Metal markerboard Tiles fit into the grooves of the panel frame and the lower rail. Tile edges are concealed when installed next to an end or mid panel. Additional trim is not required. Tiles are recommended to be the same material option for both sides of the frame. When specifying tiles for a configuration including connectors, select a tile material option that matches the tile insert material on the connector for a continuous material application. Connectors are available with a fabric insert to match fabric tiles, or paint to match laminate, metal, or metal markerboard tiles. End trim is required to cover the tile edges when used with a T-leg at the end of a run. Page 4.15

16 Power Panel Components Connectors Planning Details Smooth Top Cap Cable Cut-Out Panel (Beam) Trim Insert (Paint or Fabric) Connectors enable the structure to continue in a straight line or turn a corner for a change of direction. They are available in one height, specific to power panel structures. Six directional types are available: S (straight, inline) L (2-way 90 ) V (2-way 120 ) T (3-way 90 ) Y (3-way 120 ) X (4-way 90 ) L-connector is used to connect two beams at a 90 angle. V-connector is used to connect two beams at a 120 angle. Y-connector is used to connect three beams at a 120 angle. X-connector is used to connect four beams at a 120 angle. Floor glides are standard in black and provide 2 3 4" of height adjustment. Post Leg Parts of L, V, T, Y, and X connectors can be specified in contrasting colors. Kimball suggests that the top cap and beam trim be specified to match the adjoining beam. Panel trim is continous on the inside and outside of L-, V-, T-, and Y-connectors; panel trim is on the inside only on X-connectors. Post legs can be specified the same color as the beam or to match T-legs, if they are a contrasting color. Specify the insert to match the tile type selected for the power panel. Cut-out in connector allows power jumper and data cables to be routed through the connector in power panel-to-panel applications. Cut-out can accommodate two jumpers passing through the opening. See page 4.31 for electrical jumper lengths. IMPORTANT: Jumpers should be installed through a directional connector prior to assembling the connector. Planning Factors L, V, T, Y, and X connectors will not accommodate a power entry. See page 4.17 for stability guidelines. Connections Bolts, standard with each connector model, are used to attach the connector to the panel frame. S-connector is used to create straight, in-line applications. It consists of a post leg with a cut-out at the top like the T-leg to route jumpers and cables from beam-to-beam. It can only be specified in the middle of a run between two T-legs or with a directional connector; it cannot be used at the end of a run. T-connector is used to connect three beams at a 90 angle. Top caps are smooth, painted wood. They attach to slots in the connector. Power beam top rail design intersects with the top cap Page 4.16

17 Stability Guidelines For and Power Panels Planning Minimum run must consist of: One horizontal beam or panel frame T-leg or end panel at each end End of run must always be supported by: T-leg or end panel T-legs should be used at the end of a run or inline at all junctions when maximum stability is desired. There is no limit on the maximum run, as long as every other power beam or power panel is supported by one of the following: T-leg Directional L-, V-, T-, Y-, or X-connector End panel Mid panel See examples below. When specifying S-connectors every other power beam or power panel must be supported by a T-leg, directional connector, end panel, or mid panel. S-connectors can be in applications supporting screens, but should not be used with overhead storage. When supporting overheads, T-legs are required at all junction points in a straight run. Overheads can be placed on power beams and power panels that have a combination of T-legs and connectors. Page 4.17

18 End and Mid Panels Overview Planning End and mid panels attach to power beams and power panels to provide space division and offer privacy between occupants. They replace T-legs and connectors, and provide support for the horizontal power beam and power panel. Panels are " thick. Mid panels attach between two beams or panels to separate users. TFL or HPL end panels are particle board with laminate on both sides and an 1 8" (3mm) vinyl edgeband on the top and sides. Vinyl edgeband can be selected to match the laminate or in a contrasting color. Wood end panels are particle board with veneer on both sides and an 1 8" (3mm) wood edgeband on the top and sides. Edgeband and the veneer will be the same finish. End panels attach to the beam or panel at the end of a run for aisle privacy. Glides are standard and provide 1 1 2" of adjustment. Page 4.18

19 End and Mid Panels Product Information Planning Details End and mid panels are modelspecific for low beams, high beams, and power panels. Single-sided widths are 28" and 34"; dual-sided widths are 51" and 63". End and mid panels are "H. They align with: "H center-mount fixed screen on a high power beam, or "H center-mount fixed screen on a low power beam Footprint overhead on high power beam or power panel panel. They replace the T-leg and end trim at the end of a run and provide support for the horizontal structure. Planning Factors Single-sided end and mid panels provide privacy to one side of a beam or panel. End panels are specified as right or left (right-hand panel application is shown above). Singlesided mid panels are non-handed. Grain direction runs horizontally on all end panels. Connections Dual-sided and single-sided mid panels ship with two black attachment brackets that mount directly to the mid panel on both sides and the horizontal power beams or power panels. They replace the T-leg or connector located between beams or panels and provide support for the horizontal structure. When planning for a single-sided end or mid panel, deduct the beam thickness for inside dimensions "W end or mid panel has a "D clearance; "W end or mid panel has a "D clearance (righthand panel application is shown above). A mid panel plus T-legs at both ends of a run can support a run of beams or power panels. Single-sided end panels are available left or right-handed. This is determined by the user facing the attaching beam or panel; left side application is shown above. Dual-sided end and mid panels are designed for the beam or panel to intersect at the center of the panel. Dual-sided end and mid panels are non-handed. Dual-sided and single-sided end panels ship with one black attachment bracket that mounts directly to the end panel and the horizontal power beam or power Mid panels and their attachment brackets feature an opening to allow electrical jumpers to pass power between horizontal structures. When planning for a dual-sided end or mid panel, deduct the beam thickness for inside dimensions "W end or mid panel has a "D clearance on each side; "W end or mid panel has a "D clearance. Single-sided mid panels are nonhanded and can be used on either side of the horizontal structure between two beams or power panels. Page 4.19

20 Screens Product Information Planning Details Screens provide a boundary along with power beams and power panels. They are available in several material options and heights to accommodate varying levels of privacy. Screens are available in: Tackable fabric Tackable fabric with accessory rail(s) Frameless glass Frameless resin Low power beams accept "H tackable fabric screens with or without an accessory rail. High power beams and power panels accept 14"H frameless glass, 14 H frameless resin, or "H tackable fabric screens. Tackable fabric screens are available in two heights: " (shown) and ". They feature a tackable fabric surface (panel or seating fabric) with an aluminum frame available in all paint colors. Attachment brackets are painted to match the frame. Note: 30"H tackable fabric screens are not recommended for use on high beams or power panels due to tipping. Tackable fabric screens with accessory rail are available in two heights: " and " (shown). They accept Canopy screen accessory rail work tools. Accessory rail can be specified on one side or both sides of the screen. The accessory rail runs with the width of the screen and is located 4" from the top of the screen; rail is 1 2"H. Accessory rail is painted to match the frame and attachment brackets. Note: 30"H tackable fabric screens with accessory rail are not recommended for use on high beams or power panels due to tipping. Frameless resin or glass provide space division without impacting or compromising the open feel and access to daylight views. Quarter-inch thick resin or glass panes are 14"H. Glass is tempered for safety. Resin panes are available in Glacier; glass is available in Charcoal, Clear, Bronze, and Etched. Connections Tackable fabric screen brackets bolt to the top rail on power beam or power panel. Frameless glass and resin are held in place in the power beam or power panel s top rail with nylon retainer clips (shown above); included as standard. Available in four colors. Related Products Six Canopy screen accessory rail work tools are available for use with Xsede screens. They are available in all paint colors to accent the workspace. See the Canopy chapter in the Price List. Page 4.20

21 Worksurfaces Product Information Planning Details 2 5 8" Connections Worksurfaces for use with high power beams and power panels are available in the following shapes Rectangular 120 full-depth curved corner Worksurfaces have square edges are and are available in 1 1 8"-thick thermally fused laminate (TFL) "-thick high-pressure laminate (HPL) Softened rim profile on TFL and HPL worksurfaces is 1 /8" (3mm) vinyl and appears on all four sides. Full-depth 120 curved corner worksurfaces are available in one size for use with 48"W high power beam or power panel specified with a Y connector; grain direction runs diagonally. Factory-installed grommets and cutouts are available as an option on all full-depth worksurfaces (except touchdown) in pre-determined locations: Left Right Left and right Left, right, and center 7 8" 2 3 4" 2 1 4" dia " dia. 7 8" G19 metal grommet is a two-piece unit with black brush access. Top locks in place. Powdercoat finish in the following colors: 405 Designer White 501 Platinum Metallic 514 Carbon Metallic 490 Polished Chrome 487 Brushed Nickel 544 Silver Pearl G28 cut-outs are designed for use with Ellora power/usb/data center (45APDCS). Worksurface brackets are used to attach worksurfaces to the power beam or power panel. See page Flat steel brackets attach worksurfaces to each other. See page Undersurface support rails are required by some worksurface sizes. See page Undersurface support legs, U-legs, or O-legs are required to provide undersurface support for worksurfaces. See page When specifying 120 curved corner worksurfaces, two undersurface support legs (model 45F0227USP) will be required to support the front of the surface. Full-depth rectangular worksurfaces are sized in widths of 30" to 84" in 6" increments. Depths are 24" and 30". Grain direction runs with the width. G1 plastic grommet is a two-piece unit with snap-in lid. Lid cutout slides open to route cables or can be closed when not in use. Matte black. G27 cut-outs are designed to accept surface-mount power/data center (model 45A0307PDGS). IMPORTANT: All power/data centers must be specificed searpately for field installation. Page 4.21

22 Worksurface Support Product Information Planning Details Connections Undersurface support leg is screwed to the underneath side of a worksurface, providing additional support. Related Products Worksurface brackets are specified separately and are used to connect worksufaces to the power beam or power panel structure. Flat brackets are used to connect two adjacent worksurfaces together at a worksurface joint. Two flat brackets are required when joining two main worksurfaces or in a return or bridge application. Undersurface support rails are 3 4"H and can be used underneath the worksurface to provide support for up to 72" of unsupported span. For unsupported span of 54" 60"W, use undersurface support rail model AC48WSSR. For unsupported span of 66" 72"W, use undersurface support rail model AC72WSSR, which features a tension adjustment. Over 72" of unsupported span requires the use of a support leg. O-legs and U-legs are 14-gauge steel with a powdercoat finish. They are used to support extension worksurfaces attached to high power beams or power panels. Extension worksurfaces cannot exceed 72". They can also be used as midsupport for longer worksurface spans that are attached parallel to the power beam or power panel. Planning Factors Number of Worksurface Worksurface Width Brackets 24" 48" 2 54" 72" 3 78" 84" 4 24" and 30"D worksurfaces installed as an extension always require two brackets. Worksurface bracket should be located at the seam where two worksurfaces meet. 4"H glide cover provides a cosmetic leg sleeve that can be added to all legs to hide extended leveling glides. Glide cover is made of aluminum and can be painted same color as the leg. Floor glides are standard on all legs. Glides on support legs provide 2 3 4" height adjustment. Worksurfaces installed along a power beam or power panel with connectors will have a 1" gap between the worksurface and the power beam or panel. T-legs, straight connectors, and mid or end panels can be installed flush or withi a gap. Undersurface support legs are 14- gauge steel with a powdercoat finish. they can be used to support the front of a worksurface attached to a high power beam or as a mid-support for unsupported spans over 60". Plate on top of leg can be repositioned in the field based on installation needs. Page 4.22

23 Worksurface Support Application Guidelines Planning Select worksurfaces can be attached to high power beams and power panels for static worksurface applications. Worksurfaces with directional connectors will be mounted with a 1" gap at the back. Worksurface bracket (model 45F4WBP) attaches the worksurface to the power beam or power panel structure. 24 D x 60"W worksurfaces requires three brackets across the back and two at the ends. Brackets are inset 2" from each end for proper support. Required undersurface support rail (model AC48WSSR) is centered on the 60" worksurface width and mounted 6" off the user's edge. Undersurface support leg (model 45F0227USP) is required at the outside corners of each surface. Page 4.23

24 Worksurface Support Application Guidelines, continued Planning 84"W middle worksurface requires four worksurface brackets (model ADFWBP) to attach to the high power beam or power panel. Worksurfaces with in-line arrangements can be mounted flush to the beam or with a 1" gap at the back. 30"D worksurface extensions require two worksurface brackets (model 45F4WBP) to attach to the high power beam or power panel. Unsupported spans over 48" require an undersuface support rail. 72"W worksurface requires model AC72WSSR, specified separately. Maximum width of an extension worksurface is 72". Extension ends will require a U-leg (shown) or an O-leg. Undersurface support leg (model 45F0227USP) is required at the center of the worksurface. The leg can be flush with the front or inset. Page 4.24

25 Integrating Footprint and Priority Overhead Storage Application Guidelines Planning Select Footprint and Priority center-mount overhead storage units are compatible with Xsede high power beams and power panels. Compatible models are identified in this price list for convenience in specifying, but are the same ones found in their respective price lists. Applicable models include: Footprint center-mount, open overhead cabinets See page Footprint center-mount, sliding-door overheads See page Priority center-mount, sliding-door (solid or writable glass door) See page Priority center-mount straight shelves See page Footprint flat profile, centermount sliding door and open overheads mount to the top cap accessory rail with stanchion mounting brackets, specified separately. Footprint overheads can be installed next to a Priority shelf and will align along the bottom. Stanchion brackets will be different models, however, due to mounting to wood or metal. Priority straight shelves and sliding door center-mount overheads mount to the top cap accessory rail with stanchion mounting brackets, specified separately. Page 4.25

26 Integrating Footprint and Priority Overhead Storage Application Guidelines, continued Planning Footprint Overhead Storage Priority Overhead Storage Planning Factors: See the Footprint chapter in the Kimball Surfaces and Storage Price List for additional product and planning information. One-sided open cabinets feature a finished back and center panel that divides space. See the Priority chapter in the Kimball Desks & Accessories Price List for additional product and planning information. Footprint one-sided, center-mount sliding-door models have one sliding door. A center panel divides the space; one compartment will be open at all times. Footprint two-sided, center-mount sliding-door models feature onesliding door on each side. Center panel divides the space and each compartment features a fully finished back panel. Both sides can be locked independently on locking models; they must feature the same keying option. Two-sided open cabinets are feature a center panel divides the space; each compartment features a finished back panel. Footprint overheads mounted to a high power beam or power panel will be "H and will align with end and mid panels. Mounting stanchion brackets, model 14SXAR (sold in a set of 2), must be specified separately. Each overhead requires two stanchion brackets. Brackets are inset 7 8" from the end of each overhead. Priority one-sided, center-mount sliding-door models have one sliding door. A center panel divides the space; one compartment will be open at all times. Writable glass models features thin aluminum frame finished in silver satin metallic; non-locking. Priority center-mount shelves feature a finished top and bottom and have a softened rim on all four sides of the shelf. Mounting stanchion brackets, model 53KSKOP (sold individually) must be specified separately. Specify two brackets per overhead or shelf. Brackets are inset 3" from the end of each overhead or shelf for proper support. Priority overheads can be ganged together, but will still require two stanchion brackets for each individual overhead cabinet. Priority overheads mounted to a high power beam or power panel will be "H and will be taller than end and mid panels. Priority shelves mounted to a high power beam or power panel will be "H and will align along the bottom with both Footprint and Priority center-mount overheads. Overheads and shelves can be the same width or a narrower width than the high power beam or power panel to which they are mounted. Overheads and shelves can be specified for freestanding high power beams or power panels with attached fixed-height worksurfaces. When specifying overheads and shelves in combination with adjustable-height tables or desks, position the placement of tables so they do not collide with the storage unit when raising or lowering the table or desk. Page 4.26

27 Integrating Narrate Panels Planning Narrate transition brackets are available to span a high power beam or power panel from Narrate two-high support Traxx. Narrate transition bracket is specific to a high poewr panel or power panel application; not applicable to low power beams. Bracket attaches to a T-leg or S-connector with screws. Top of the bracket slides into groove in the support Traxx. Narrate panels and Xsede power beam or power panels have different power components. They can be connected with the following requirements: Narrate must have a 20-amp receptacle to plug in a circuit 1 power entry going to the Xsede power beam or panel. Power beam or power panel must utilize 15-amp Circuit one receptacles only. Metal cable manager is available to cover the power entry that runs down the T-leg or connector and plugs into the Narrate panel. Cable manager clips onto any side of the T-leg or S-connector. Page 4.27

28 Ceiling Power Pole Covers Product Information Planning Ceiling power pole covers route power and data from the ceiling to power beams and power panels. They are available as an end connection or S connection (straight). Details Beam trim paint Ceiling pole paint Adjustable ceiling trim secures pole in place. Maximum ceiling height is 10'. The pole extends through a cut-out in the ceiling tile. End-connection poles attach to the end of a power beam or power panel with a t-leg support. The pole is not supporting; a T-leg must be specified. End poles are available in all paint colors. S-Connection Pole for Use with Power Beam S-connection poles are supporting and replace an S-connector in a run and follow the same stability guidelines. S-connection poles are available in all paint colors. Face Cap Lower post paint End-connection poles ship with bolt locations specific for use with a power beam or power panel (power beam shown). End trims are not specified with an end-connection pole. The pole finishes off the exposed end of the power beam or panel. An end trim installed between the pole and the beam or panel would block the power-infeed from entering the run. Mounting bolts End Connection S Connection Panel trim paint Ceiling pole paint Fabric or paint to match panel Lower post paint 1.61 sq. in sq. in. Moveable Divider Moveable divider inside the pole can create a physical separation between power and data. Related Products 12' power entry is required and must be specified separately. System connection to building power must be made by a licensed electrician. Ceiling power entries do not include junction box and related connectors. S-Connection Pole for Use with Power Panels 6" of ceiling power entry conduit is required above the ceiling for electrical connections. Page 4.28

29 8-Wire Power Components Overview Planning Center location power kit ships with a dual distribution block. Duplex reeptacles are ordered separately. Cable managers clip on to T-legs and S-connectors to cover power entry. Power entry powers the structure from the floor (shown) or the ceiling. Horizontal structures include: Rail top cap Electrical covers with wire trough Distribution blocks Power harness J-hooks Jumpers extend power beam-tobeam and are ordered separately. Left and right location power kits ships with a power harness to connect power between distribution blocks. J-hooks manage power harness, jumper, and cables Page 4.29

30 8-Wire Power Components Product Information Planning Details IMPORTANT: The building s power capability should be determined before power is configured and components specified. IMPORTANT: Planning actual power supplies and branch circuits, as well as installation, must be performed by qualified electricians or electrical engineers. 8-wire power system for Xsede power beams and power panels utilizes the same componentry to Dual-sided power beams and panels ship with a specific power kit based on outlet cut-out locations: Power Block Center Location Power Kit One dual-sided, double distribution block Specify 4 duplex receptacles separately power structures. Two power entry solutions are available: 8-wire floor or ceiling power entry Circuit-1-only floor or wall entry 8-wire, 4-circuit (3+1 or 2+2) floor power entry accommodates 15-amp or 20-amp duplex receptacles. They are available in 6' and 12' long models. One Left, One Right Location Power Kit Two dual-sided, single distribution blocks Power harness Specify 4 duplex receptacles separately Circuit-1-only power entry is 10' long and can be a quick solution for a maximum of 12 duplex receptacles. This power entry includes a 20-amp plug which must plug into a 20-amp outlet; for use with circuit or 20- amp receptacles only. Connection is made by snapping into the end of the distribution block. New York power entry allows hard - wiring to comply with local codes. Power entries can be located next to a T-leg or S-connector on power beams and power panels. Other directional connectors cannot be used for power entry. Power beams can accom modate a power entry next to an end- or mid-panel, or anywhere along the underside of the horizontal structure as it is open. Two Left, Two Right Location Power Kit Two dual-sided, double distribution blocks Power harness Specify 8 duplex receptacles separately Data Adapter Kit Reference: Kit provides adapter for a variety of manufacturer s jacks and couplers and two solid blanks. Jacks and cables are not included. Select black or white plastic. Manufacturer Systimax/CommScope Uniprise/CommScope L-Com Keystone Modular Tyco SL and 100 Connect Series Modular Siemon Keystone Style Allen Tel Versa Tap Series Leviton Quick Port Series Nordx Keystone Style Tyco SL Coupler Series Krone 6000 Series/ADC Hubbell Xcelerator Keystone Series Blank (no coupler/jack) Ortronics TracJack Series Panduit Mini-Com Series Microphone Jack/3-pin XLR, solder type only Video Monitor Jack/DB-15, panel-mount solder style Adapter* AA AA BB BB BB BB BB BB CC CC CC DD EE FF GG HH *Adapter identifier is located on the backside of the plate. Page 4.30

31 8-Wire Power Components Product Information, continued Planning Receptacles are specified separately and snap into the block. Available in black and white. 15-amp 20-amp Duplex receptacles are rated at 15 or 20 amps. 20-amp models are required for some large equipment applications and have a keyed-slot on the Hot side of the receptacle. Duplex receptacles are available in black or white and the designated/dedicated models have a Δ imprinted on them for use as a visual aid. Universal serial bus (USB) powered receptacles are 2-amp, circuit-1-only. They can be used anywhere a circuit-1-only receptacle is used. Each receptacle provides two powered USB ports to provide charging/power capabilities for peripheral devices. Two data cut-outs on each side of the power beam or power panel, for a total of four openings, are standard. Each model ships with two data adapter kits. Jumpers are specified separately. Specify jumper lengths based on the following charts. Jumpers connect into each side of dual-sided double distribution boxes that are standard with power beam and power panel models in beam-tobeam or panel-to-panel applications. Each block has multiple connection points to allow branching of power for configurations. For center-to-center power locations in in-line applications with T-legs, S-connector, end panel, or mid-panel: Jumper Model For same-width beams or panels 48" + 48" 45F38EJB8 60" + 60" 45F50EJB8 72" + 72" 45F62EJB8 For different-width beams or panels 48" + 60" 45F44EJB8 48" + 72" 45F50EJB8 60" + 72" 45F56EJB8 For center-to-center power locations with directional connectors (L, V, T, Y, or X): Jumper Model For same-width beams or panels 48" + 48" 45F40EJB8 60" + 60" 45F52EJB8 72" + 72" 45F64EJB8 For different-width beams or panels 48" + 60" 45F50EJB8 48" + 72" 45F52EJB8 60" + 72" 45F62EJB8 For end-to-end (left and right locations) power locations in in-line or directional applications with T-legs, any connector, end panel, or midpanel: Jumper Model For same-width or different-width beams or panels 45F30EJP8 For center-to-end (left and right locations) power locations in in-line or directional applications with T-legs, any connector, end panel, or midpanel: Jumper Model For same-width beams or panels 48" center + 48" end 45F42EJP8 60" center + 60" end 45F38EJB8 72" center + 72" end 45F40EJB8 For different-width beams or panels 48" center + 60" end 45F42EJP8 48" center + 72" end 45F42EJP8 60" center + 48" end 45F38EJB8 60" center + 72" end 45F38EJB8 72" center + 48" end 45F40EJB8 72" center + 60" end 45F40EJB8 Page 4.31

32 8-Wire Power Components Circuit Configurations and Wiring Diagrams Planning Ground Isolated Ground Neutral, 12 gauge Neutral, 10 gauge Hot Hot Hot Hot 8-wire power entry allows power to enter from the floor, ceiling, wall, or column. Power can be distributed either above or below worksurfaces. If power is required above and below, two separate power entries are required. 8-wire systems accom - modate up to 13 duplex receptacles per circuit and include four 12-gauge hot wires, one 12-gauge neutral wire, one 10-gauge shared neutral wire, and two 12 gauge ground wires. Xsede s electrical system is rated for 20-amp service. To support the usage, 15-amp convenience receptacles can be placed anywhere along the leg of the electrical connection. In the event that an appliance, such as a larger printer/copier/plotter needs to have a 20-amp receptacle, it is recommended to use a dedicated circuit with a 20-amp receptacle. Using 15-amp convenience receptacles will aid in ensuring that no one leg of the system can pull too much current, which could potentially cause the system to trip out and lose power across the entire system. 3 and 1 (8-Wire) Configuration: Circuits 1, 2, and 3 share a neutral and common ground, providing circuits for general electrical needs. Customarily, one or more of the circuits are reserved for lighting or other everyday uses, which allows control by central or master switching. 2 and 2 (8-Wire) Configuration: 4D Dedicated Neutral 3 4 4D 3D Dedicated Neutral Circuit 4 consists of three separate conductors (hot, neutral, and ground) and meets the BIFMA/ANSI definition for a dedicated circuit. 15-amp 20-amp Cir. Model Model 1 45FER FER FER FER FER FER FER4D815 45FER4D820 IMPORTANT: Planning actual power supplies and branch circuits must be performed by qualified electricians or electrical engineers familiar with the National Electrical Circuits 3 and 4 provide a pair of designated circuits for computer applications. 15-amp 20-amp Cir. Model Model 1* 45FER FER FER FER FER3D815 45FER3D FER4D815 45FER4D /240V 1 Phase Shared Neutral Receptacles: 1, 2, 3, 4D Code and the appropriate local codes. The information provided here is intended to assist specifiers. 120/240V 1 Phase Shared Neutral Receptacles: 1, 2, 3D, 4D IMPORTANT: Xsede electrical components are UL listed under the Xsede name and are not inter changeable with other Kimball series. Circuits 1 and 2 provide a pair of designated circuits for general electrical needs. * 45FERUP (powered USB receptacle) can be used in place of circuit 1 tray receptacles Page 4.32

33 Power Beam Components Dual-Sided GSA SIN D W H Model Price With Two Duplex Receptacle Openings per Side, Center 4 5 8" 48" 7 7 8" 45F4808DPB2CP $ " 60" 7 7 8" 45F6008DPB2CP " 72" 7 7 8" 45F7208DPB2CP 1208 With Two Duplex Receptacle Openings per Side, One Left and One Right 4 5 8" 48" 7 7 8" 45F4808DPB1L1RP $ " 60" 7 7 8" 45F6008DPB1L1RP " 72" 7 7 8" 45F7208DPB1L1RP 1275 Standard Includes One horizontal beam Dual-sided electrical distribution block and power kit Two data plate adapter kits 2 Paint designator 3 Data adapter kit B = Black W = White With Four Duplex Receptacle Openings per Side, Two Left and Two Right 4 5 8" 48" 7 7 8" 45F4808DPB2L2RP $ " 60" 7 7 8" 45F6008DPB2L2RP " 72" 7 7 8" 45F7208DPB2L2RP 1523 Low beam t-legs, tall beam t-legs, end trim. See page Power components See page Page 4.33

34 Power/Data Beams and Power/Data Panels Power Beam Components Support Legs and End Trim GSA SIN D W H Model Price Low Beam Support T-Leg " 2 3 8" " 45F2017STLPBP $320 Standard Includes T-Leg One leg Attachment hardware End Trim One end trim Attachment hardware High Beam Support T-Leg " 2 3 8" " 45F2028STLPBP $326 2 Paint designator End Trim 1 16" 2 3 4" 7 7 8" 45F0308ETPBP $57 Page 4.34

35 Power Beam Connectors S-Connectors (Straight) GSA SIN D W H Model Price For Use with Low Beam 1 1 8" 2 3 8" " 45F0217CSPBP $193 Standard Includes One connector Attachment hardware 2 Paint designator For Use with High Beam 1 1 8" 2 3 8" " 45F0228CSPBP $200 Page 4.35

36 Power Beam Connectors L-Connectors (2-Way 90 ) GSA SIN D W H Model Price For Use with Low Beam 5 3 4" 5 3 4" " 45F0617CLPBP $499 Standard Includes One connector Top cap Attachment hardware For Use with High Beam 5 3 4" 5 3 4" " 45F0628CLPBP $525 2 Top cap and trim paint designator 3 Post paint designator Page 4.36

37 Power Beam Connectors V-Connectors (2-Way) GSA SIN D W H Model Price For Use with Low Beam 6 1 8" 5 1 2" " 45F0617CVPBP $580 Standard Includes One connector Top cap Attachment hardware For Use with High Beam 6 1 8" 5 1 2" " 45F0628CVPBP $610 2 Top cap and trim paint designator 3 Post paint designator Page 4.37

38 Power Beam Connectors T-Connectors (3-Way 90 ) GSA SIN D W H Model Price For Use with Low Beam 6 7 8" 5 3 4" " 45F0617CTPBP $530 Standard Includes One connector Top cap Attachment hardware For Use with High Beam 6 7 8" 5 3 4" " 45F0628CTPBP $562 2 Top cap and trim paint designator 3 Post paint designator Page 4.38

39 Power Beam Connectors Y-Connectors (3-Way) GSA SIN D W H Model Price For Use with Low Beam 5 5 8" 6" " 45F0617CYPBP $665 Standard Includes One connector Top cap Attachment hardware For Use with High Beam 5 5 8" 6" " 45F0628CYPBP $710 2 Top cap and trim paint designator 3 Post paint designator Page 4.39

XSEDE HEIGHT ADJUST. Table of Contents. Xsede Height Adjust Kimball Benching. Price List Effective Dates: Pricing Revision

XSEDE HEIGHT ADJUST. Table of Contents. Xsede Height Adjust Kimball Benching. Price List Effective Dates: Pricing Revision HEIGHT ADJUST Table of Contents Price List Effective Dates: Pricing 07.02.18 Revision 11.09.18 See page Product Positioning page 3.2 Statement of Line page 3.4 Freestanding Desk Components 3.4 Freestanding

More information

ALLOY BENCHING PRODUCT SPECIFICATIONS

ALLOY BENCHING PRODUCT SPECIFICATIONS WORKSURFACES Worksurfaces are always sold with base unit Laminate 1 3 / 16 HPL (high pressure laminate) or 1⅛ TFL (thermally fused laminate) Softened 3mm PVC rim Grain direction runs left-to-right Autumn

More information

Flat Screen Garage. Table System Planning Guide WORKING FOR YOU

Flat Screen Garage. Table System Planning Guide WORKING FOR YOU Flat Screen Garage Table System Planning Guide ORKING FOR YOU Introduction Bring a new level of performance to any room with KI s Flat Screen Garage. This versatile system does double duty to make the

More information

WORKCENTER ACCESSORIES

WORKCENTER ACCESSORIES THE PERFECT BLEND OF STYLE AND FUNCTIONALTITY Workrite s workcenter accessory products provide complete solutions for outfitting the modern workstation. Select from a wide variety of accessory options

More information

U-SERIES SPECIFICATION GUIDE

U-SERIES SPECIFICATION GUIDE U-SERIES SPECIFICATION GUIDE Connectivity with flexibility For more product information visit connectrac.com, call us at 877-480 - 5637 or email us at info@connectrac.com ADA COMPLIANT - U.L. TESTED AND

More information

T A B L E O F C O N T E N T S

T A B L E O F C O N T E N T S T A B L E O F C O N T E N T S UNIT 1: INTRODUCTION... 1 BESIDE STORAGE REFERENCE MANUAL FOR CANVAS... 1 CANVAS DISCLAIMER... 1 BESIDE STORAGE EXTENSION TAB... 1 MAIN SECTIONS OF THE BESIDE STORAGE TAB...

More information

Haworth Power Technical Sheets January 2018

Haworth Power Technical Sheets January 2018 Haworth Power Technical Sheets January 2018 Includes Accessories This page intentionally left blank. Table of Contents Desk Top Port Power Tap Cord Power Tap Conduit Enchanced Power Module Flip Top Unit

More information

Rumble Seat and Hoodie

Rumble Seat and Hoodie Bivi Rumble Seat and Hoodie Rumble Seat and Hoodie Rumble Seat Bivi page 32 Fully upholstered lounge: Connect fabric Lounge shipped fully assembled 2 Connect fabric color number for upholstery 3 Options,

More information

lighting, electrics & communications

lighting, electrics & communications lighting, electrics & communications P RO D U C T M A P / TA B L E C O N T E N T S.....................4 L I G H T I N G, E L E C T R I C S & C O M M U N I C AT I O N S O V E RV I E W....4 4 L I G H T

More information

dewey statement of line

dewey statement of line 6 dewey statement of line Rectangular T-Leg Tables 27x34 Fixed & Folding Flip-Top Pin-Height Adjustable 27x36 20x36 24x36 27x48 20x48 24x48 27x54 20x60 24x60 27x60 30x60 20x66 24x66 27x66 30x66 20x72 24x72

More information

meeting tables MEETING TABLE BASICS TABLE BASE DIMENSIONS RECESSED POWER/DATA MODULE DETAILS

meeting tables MEETING TABLE BASICS TABLE BASE DIMENSIONS RECESSED POWER/DATA MODULE DETAILS MEETING TABLE BASICS............................ TABLE BASE DIMENSIONS........................... RECESSED POWER/DATA MODULE DETAILS.............. MEETING TABLE CONFIGURATIONS & SUPPORTS.......... MEETING

More information

lighting, electrics & communications

lighting, electrics & communications lighting, electrics & communications PRODUCT MAP / TABLE OF CONTENTS.................. LIGHTING, ELECTRICS & COMMUNICATIONS OVERVIEW.... LIGHTING BASICS................................. MODULAR DESK APPLICATIONS:

More information

electrics PRODUCT MAP / TABLE OF CONTENTS ELECTRICS & COMMUNICATIONS OVERVIEW POWER ENTRY BASICS PANEL-MOUNTED WORKSTATIONS..

electrics PRODUCT MAP / TABLE OF CONTENTS ELECTRICS & COMMUNICATIONS OVERVIEW POWER ENTRY BASICS PANEL-MOUNTED WORKSTATIONS.. PRODUCT MAP / TABLE OF CONTENTS.................. ELECTRICS & COMMUNICATIONS OVERVIEW............. POWER ENTRY BASICS PANEL-MOUNTED WORKSTATIONS.. POWER & COMMUNICATIONS BASICS PANEL-MOUNTED WORKSTATIONS.....................

More information

Power/Data Instructions. Genius. Movable Walls. September

Power/Data Instructions. Genius. Movable Walls. September Power/Data Genius Movable Walls September 2011 Genius Movable Walls Power and Data in Shell Level 1 Conventional Boxes in Panel (conventional box and conduit) Choose 2x4 box or 4x4 box (shown). Separate

More information

worksurface supports & accessories

worksurface supports & accessories worksurface supports & accessories P RO D U C T M A P / TA B L E O F C O N T E N T S..................2 8 4 W O R K S U R FA C E S U P P O RT S PA N E L M O U N T E D O V E RV I E W....2 8 8 W O R K S

More information

ABERDEEN LAMINATE SERIES

ABERDEEN LAMINATE SERIES ABERDEEN LAMINATE SERIES The Aberdeen Series of laminate casegoods combine fashionable aesthetics and unparalleled quality all in a package that is surprisingly affordable. Aberdeen s transitional style

More information

FUNDAMENTAL. Table of Contents. Metal Filing. Fundamental Kimball Surfaces & Storage. Price List Effective Dates: Pricing Revision

FUNDAMENTAL. Table of Contents. Metal Filing. Fundamental Kimball Surfaces & Storage. Price List Effective Dates: Pricing Revision Table of Contents Price List Effective Dates: Pricing 02.04.19 Revision 01.16.19 See page Statement of Line page 5.2 Overview page 5.3 Product Information page 5.4 Filing Capacities page 5.5 Locking Information

More information

lighting, electrics & communications

lighting, electrics & communications lighting, electrics & communications P RO D U C T M A P...................................2 9 0 289 L I G H T I N G, E L E C T R I C S & C O M M U N I C AT I O N S O V E RV I E W....2 9 4 L I G H T I N

More information

Emerald Cubicle System. Spec Sheet. Emerald 39,52, 65 H. skutchi.com cubicles.cc. Vol DESIGNS. inc.

Emerald Cubicle System. Spec Sheet. Emerald 39,52, 65 H. skutchi.com cubicles.cc. Vol DESIGNS. inc. Emerald Cubicle System Spec Sheet 2018 Emerald 39,52, 65 H skutchi.com cubicles.cc Vol. 1 2018 Emerald Cubicles The diverse Emerald System has endless solutions for your office. Whether you are looking

More information

Passage Desking System

Passage Desking System high-capacity power and data Three easy-to-access horizontal raceways in desk modules manage energy and cables below the work surface. The top channel holds cords routed from the work surface, so there

More information

Smartspace Benching System

Smartspace Benching System SIN 711-2 Smartspace Benching System With the increase in office collaboration, comes an easy-to-install benching solution. Now that's smart thinking. Easily integrate power trough allows every workstation

More information

PRODUCT SPECIFICATIONS Pillar Table

PRODUCT SPECIFICATIONS Pillar Table PROUT SPIITIONS Pillar March 2017 Worksurfaces Standard worksurface tops are nominal 1 1 / 4 overall thickness with.030 thick high-pressure laminate top surface and.028 phenolic backer (bottom surface).

More information

Electrical Accessories

Electrical Accessories 2017 Price List and Specifications Brodart Co. Contract Furniture - Made in USA 280 North Road, Clinton County Industrial Park McElhattan, PA 17748 Toll-Free: 888-521-1884 E-Mail: furniture@brodart.com

More information

meeting tables P RO D U C T M A P / TA B L E C O N T E N T S M E E T I N G TA B L E B A S I C S

meeting tables P RO D U C T M A P / TA B L E C O N T E N T S M E E T I N G TA B L E B A S I C S P RO D U C T M A P / TA B L E C O N T E N T S....................5 7 6 M E E T I N G TA B L E B A S I C S............................5 8 0 M E E T I N G TA B L E A C C E S S O R I E S.......................5

More information

mounted storage & accessories

mounted storage & accessories mounted storage & accessories P RO D U C T M A P...................................2 5 7 M O U N T E D S TO R A G E B A S I C S.........................2 5 8 M O U N T E D A C C E S S O RY B A S I C S........................2

More information

Trig Planning Guide. December 2012

Trig Planning Guide. December 2012 Trig Planning Guide December 2012 Table of Contents Statement of Line Trig Applications - Conventional and Integration Specification Information Statement of Line Desks and Work Surfaces Support Options

More information

Standard Configuration - 4) 15 amp power receptacles 1) Cutout for configurable telecom plates. Door Finishes - UL Listed

Standard Configuration - 4) 15 amp power receptacles 1) Cutout for configurable telecom plates. Door Finishes - UL Listed power modules P-1 conference table power info List Price - PM-P-1-B - $415 Black Laminate Tech Doors PM-P-1-A - $665 Brushed Tech Doors PM-P-1-SS - $685 Solid Surface Tech Doors P-1 Power Module Power

More information

LF SERIES. Table of Contents. Metal Filing. LF Series Kimball Surfaces & Storage. Price List Effective Dates: Pricing Revision

LF SERIES. Table of Contents. Metal Filing. LF Series Kimball Surfaces & Storage. Price List Effective Dates: Pricing Revision Table of Contents Price List Effective Dates: Pricing 07.02.18 Revision 06.15.18 See page Statement of Line page 6.2 Planning page 6.3 Overview page 6.3 Product Information page 6.4 Filing Capacities page

More information

application guide westcoast price & application guide June 23, 2008 DESKS...14 RETURN & CORNER DESKS REQUIRING SHARED SUPPORT...15

application guide westcoast price & application guide June 23, 2008 DESKS...14 RETURN & CORNER DESKS REQUIRING SHARED SUPPORT...15 DESKS.......................................... RETURN & CORNER DESKS REQUIRING SHARED SUPPORT.... 13 DESKS REQUIRING SHARED SUPPORT................... BRIDGES.........................................

More information

S Y S T E M S O L U T I O N S CONTEXT

S Y S T E M S O L U T I O N S CONTEXT S Y S T E M S O L U T I O N S CONTEXT 2 The future is still out there. When Context was first introduced it challenged virtually every preconceived notion about how the workplace should look and act. It

More information

DESCRIPTION PRODUCT CODE LIST PRICE DIMENSIONS/INCHES H L D

DESCRIPTION PRODUCT CODE LIST PRICE DIMENSIONS/INCHES H L D EVE8PD - POWER DISTRIBUTION HOUSING Power housing is specified per beam size (e.g. EVE8PD36 is for use in a 36 beam). 8 wire, 4 circuits (2+2 configuration). Accommodates two duplex receptacles per panel

More information

Answer Modular Power. Page 1 of Rev V. Power Kits. Change of Height Harness. Receptical Covers

Answer Modular Power. Page 1 of Rev V. Power Kits. Change of Height Harness. Receptical Covers Answer Modular Power Change of Height Harness Power Kits Receptical Covers NOTE: Unused modular electrical connector openings are not required to be capped. NOTE: The electrician can cut conduit and wire

More information

ACCESSORIES ACCESSORIES ACCESSORIES NATIONAL OFFICE FURNITURE TABLES 519

ACCESSORIES ACCESSORIES ACCESSORIES NATIONAL OFFICE FURNITURE TABLES 519 NATIONAL OFFICE FURNITURE TABLES 59 POWER/DATA ELECTRICAL SPECIFICATIONS ROUND GROMMET (G0) NACG0EL features 2 20 volt receptacles and 2 Cat5E data ports and 6' AC cord rated at 5 Amps; data ports are

More information

SM (SURFACE MOUNTED) WIREWAY: I SERIES

SM (SURFACE MOUNTED) WIREWAY: I SERIES SM (SURFACE MOUNTED) WIREWAY: I SERIES DUPLEX POWER AND AV / TELECOM ANYWHERE The new Connectrac SM (Surface Mounted) Wireway installs directly onto any type of flooring. It s the industry s newest alternative

More information

lighting, electrics & communications

lighting, electrics & communications lighting, electrics & communications P RO D U C T M A P................................... 3 1 6 L I G H T I N G, E L E C T R I C S & C O M M U N I C AT I O N S B A S I C S...... 3 1 9 L I G H T I N G

More information

lighting, electrics & communications

lighting, electrics & communications lighting, electrics & communications L I G H T I N G B A S I C S.................................2 8 6 P OW E R & D ATA D I S T R I B U T I O N.......................2 8 8 285 lighting basics Expansion

More information

application guide D E S K S R E T U R N & C O R N E R D E S K S R E Q U I R I N G S H A R E D S U P P O RT...1 5

application guide D E S K S R E T U R N & C O R N E R D E S K S R E Q U I R I N G S H A R E D S U P P O RT...1 5 D E S K S..........................................1 4 R E T U R N & C O R N E R D E S K S R E Q U I R I N G S H A R E D S U P P O RT....1 5 13 D E S K S R E Q U I R I N G S H A R E D S U P P O RT...................1

More information

application guide D E S K S R E T U R N & C O R N E R D E S K S R E Q U I R I N G S H A R E D S U P P O RT...1 5

application guide D E S K S R E T U R N & C O R N E R D E S K S R E Q U I R I N G S H A R E D S U P P O RT...1 5 D E S K S..........................................1 4 R E T U R N & C O R N E R D E S K S R E Q U I R I N G S H A R E D S U P P O RT....1 5 13 D E S K S R E Q U I R I N G S H A R E D S U P P O RT...................1

More information

NT-2300 Series Dual Circuit Track System & Accessories

NT-2300 Series Dual Circuit Track System & Accessories ILLUMINATING THE FUTURE...SINCE 1989 NT-2300 Series Dual Circuit Track System & Accessories Type Project Catalog No. Lamp/Wattage PRODUCT DESCRIPTION Low profile, extruded aluminum track with 20-Amp rated

More information

STORAGE & ACCESSORIES

STORAGE & ACCESSORIES STORAGE & ACCESSORIES TABLE OF CONTENTS STORAGE Structural & Hanging Pedestals... 4 Mobile Pedestals... 6 Low Storage... 8 Storage Towers... 10 Lateral Files... 12 Overhead Storage... 14 ACCESSORIES Single

More information

Morrison, Currents and Reff Raceways Morrison, Currents and Reff Raceways

Morrison, Currents and Reff Raceways Morrison, Currents and Reff Raceways 2+2 3+3 Morrison, Currents and Reff Raceways 1 Morrison, Currents and Reff Raceways. More. Better. pioneered 2+2, the office systems raceway with the right balance of convenience power and protected power

More information

DOCKING STATION SPECIFICATIONS

DOCKING STATION SPECIFICATIONS ONE PERSON STATION Power Outlets Data Jack Plate Mouse Brackets Front Covers Cable Holes Cable Holes Overview: The Docking Station distributes power, data, and laptop storage to each user. It also offers

More information

This attractive raceway conceals and

This attractive raceway conceals and 5000 Two-Piece Multiple Channel Raceway Access 5000 Nonmetallic Surface Raceway System This attractive raceway conceals and organizes electrical wiring and low-voltage cabling in a sleek, handsome molding.

More information

FOUNDATION DESKS FOUNDATION. Foundation Executive Workstation.

FOUNDATION DESKS FOUNDATION. Foundation Executive Workstation. DESKS Foundation Executive Workstation. FOUNDATION Create a solid starting point for your success with HON Foundation. Personalize your office suite with this versatile collection of laminate desk and

More information

QUICK-SHIP STORAGE WORKSPACES DESKS & BOW FRONT DESK SEATING TABLES RECTANGULAR CONFERENCE DESK HIGH DENSITY STORAGE MAILROOM FURNITURE CREDENZA

QUICK-SHIP STORAGE WORKSPACES DESKS & BOW FRONT DESK SEATING TABLES RECTANGULAR CONFERENCE DESK HIGH DENSITY STORAGE MAILROOM FURNITURE CREDENZA WORKSPACES *Note: Brighton will be discontinued in 2017., call customer service 800-822-8037 before placing order. The Brighton Series is a complete line of affordable casegoods. With all laminate construction,

More information

LIGHTING S. Table of Contents. Lighting Kimball Surfaces & Storage. Price List Effective Dates: Pricing Revision

LIGHTING S. Table of Contents. Lighting Kimball Surfaces & Storage. Price List Effective Dates: Pricing Revision LIGHTING S Table of Contents Price List Effective Dates: Pricing 07.02.18 Revision 06.15.18 See page page 7.2 Planning page 7.2 Pricing page 7.3 page 7.4 Planning page 7.4 Pricing page 7.5 for Use in Chicago

More information

Modular Table Power System Installation for Runner Non-folding Plug and Play Tables

Modular Table Power System Installation for Runner Non-folding Plug and Play Tables Modular Table Power System Installation for Runner Non-folding Plug and Play Tables Topic General Safety Warnings Ganging Hardware Electrical Circuits Table of Contents Page End-to-End (Page 4) End-and-Back

More information

Benching. Standard Components. End. Many additional options available including dividers, extensions and storage. Starter. Bridge

Benching. Standard Components. End. Many additional options available including dividers, extensions and storage. Starter. Bridge The unique style and construction of this benching program allows for multiple stations with only a recessed leg at the seam. In the center is a powered spine with flip up aluminum lids for easy access

More information

B Y R N E 8 - T R A C O V E R V I E W. 1) Introduction. 2) Universally Recognized. 3) Circuitry/Keying

B Y R N E 8 - T R A C O V E R V I E W. 1) Introduction. 2) Universally Recognized. 3) Circuitry/Keying Page 1 of 6 B Y R N E 8 - T R A C O V E R V I E W 1) Introduction Byrne Electrical Specialists, Inc. provides quality, cost effective, innovative power/data distribution solutions. From initial concept

More information

36'' Plan View of Circuit Base. description sku w d h weight specifications price

36'' Plan View of Circuit Base. description sku w d h weight specifications price circuit base Circuit Base Detail View of Table Leg The Circuit conference table features a polished stainless steel 4-star table base with adjustable levelers with½ '' leveling range. The upper section

More information

NT-300 & NT-2300 Series Single & Dual Circuit Track System & Accessories

NT-300 & NT-2300 Series Single & Dual Circuit Track System & Accessories NT-300 & NT-2300 Series Single & Dual Circuit Track System & Accessories PRODUCT DESCRIPTION Low profile, extruded aluminum track with 20-Amp rated flat, solid integral conductors. Variety of connectors

More information

P R O D U C T C A T A L O G

P R O D U C T C A T A L O G PRODUCT C ATALOG 1000 SERIES CONTEMPORARY DESKS AND MODULAR WORKSTATIONS C OMPONENTS Desks-Double 72x36* 60x36 60x30 Desks-Single 72x36 72x30 66x36 66x30 60x30 48x30 Returns 60x18 48x18 42x18 36x18 60x24

More information

lighting, electrics & communications

lighting, electrics & communications lighting, electrics & communications LIGHTING, ELECTRICS & COMMUNICATIONS OVERVIEW.... 209 LIGHTING BASICS................................. 210 207 MODULAR DESKS APPLICATIONS: 207 POWER & DATA DISTRIBUTION.......................

More information

Storage. Storage GSA SIN 711-2/3 REFERENCE EMERGE PREFIX

Storage. Storage GSA SIN 711-2/3 REFERENCE EMERGE PREFIX GSA SIN 711-2/3 Storage REFERENCE EMERGE PREFIX Storage Maxon Freestanding Storage options incorporate innovative, durable designs that maximize the efficiency of your workspace. Constructed of heavy-duty

More information

T A B L E O F C O N T E N T S

T A B L E O F C O N T E N T S T A B L E O F C O N T E N T S UNIT 1: INTRODUCTION... 2 WORK TOOLS AND ACCESSORIES REFERENCE MANUAL FOR CANVAS... 2 CANVAS DISCLAIMER... 2 WORK TOOLS AND ACCESSORIES EXTENSION TAB... 2 MAIN SECTIONS OF

More information

This attractive raceway conceals and

This attractive raceway conceals and Access 5000 Nonmetallic Surface Raceway System 5000 Two-Piece Multiple Channel Raceway This attractive raceway conceals and organizes electrical wiring and low-voltage cabling in a sleek, handsome molding.

More information

This attractive raceway conceals and

This attractive raceway conceals and Access 5000 Nonmetallic Surface Raceway System 5000 Two-Piece Multiple Channel Raceway This attractive raceway conceals and organizes electrical wiring and low-voltage cabling in a sleek, handsome molding.

More information

END PANELS WIRE GRID END PANELS. Used on ends of Wall or Island sections End Panel hooks are reversible for left hand and right hand applications

END PANELS WIRE GRID END PANELS. Used on ends of Wall or Island sections End Panel hooks are reversible for left hand and right hand applications END SOLUTIONS 133 END PANELS Used on ends of Wall or Island sections End Panel hooks are reversible for left hand and right hand applications Example Part # : EP 48 22 06 LAX 1. End Panel: EP 2. Uprite

More information

lighting, electrics & communications

lighting, electrics & communications lighting, electrics & communications ELECTRICS & COMMUNICATIONS OVERVIEW............. LIGHTING BASICS................................. 205 POWER POLE BASICS............................... POWER ENTRY FROM

More information

Hardware & Accessories

Hardware & Accessories Hardware & Accessories Assure that your installations and designs are completed in professional fashion by utilizing Stylmark s Hardware and Accessories. This catalog represents a collection of these items,

More information

UNDERCARPET CABLING SYSTEM For Power and Communications

UNDERCARPET CABLING SYSTEM For Power and Communications UNDERCARPET CABLING SYSTEM For Power and Communications Linking Everything Together Power, Voice, and Data December 5, 2007 Undercarpet Cabling System Overview What is Undercarpet Cabling? Primary Applications

More information

2015 ECA TELECOM OPTIONS REVIEW

2015 ECA TELECOM OPTIONS REVIEW 2015 ECA TELECOM OPTIONS REVIEW INTRODUCTION WHAT ARE TELECOM PLATES: 3.18 ECA Telecom Plates are proprietary and designed to fit into any ECA power solution that includes a telecom plate cutout. Each

More information

TABLE OF CONTENTS C.I.T.É. 2 C.I.T.É. USA JANUARY 2017

TABLE OF CONTENTS C.I.T.É. 2 C.I.T.É. USA JANUARY 2017 TABLE OF CONTENTS SURFACES: / SINGLE-SIDED, DOUBLE-SIDED, 120 / WITH OR WITHOUT RACEWAY... 3 STORAGE MODULES: / HUTCHES / BOOKCASES / RAILS... 6 BASES: / LATERAL / CENTER... 7 STORAGE BASE MODULES: / LATERAL

More information

POWER / DATA SOLUTIONS

POWER / DATA SOLUTIONS POWER / DATA SOLUTIONS Primeway offers a wide variety of power/data solutions. From simple power to units with data options or just blank ports for customer provided components. All units enable users

More information

ACCESSORIES price list effective January 1, 2018

ACCESSORIES price list effective January 1, 2018 ACCESSORIES price list effective January 1, 2018 modesty panels Laminate Modesty Panels Top Size Base Model Number Hardware 3P 3W F2 10 x 36 Static MP1036 02 Black $ 104 $ 216 $ 159 Nesting MP1036NE 02

More information

Al uminum Raceway is sleek, clean and

Al uminum Raceway is sleek, clean and Architectural Aluminum Raceway AL5200 Aluminum Raceway Al uminum Raceway is sleek, clean and attractive. Integrated into casework or lab furniture or installed as baseboard, these raceways distribute communication

More information

SPECTRUM-2 CONSOLES. TEL: WEB: winsted.com

SPECTRUM-2 CONSOLES. TEL: WEB: winsted.com SPECTRUM-2 CONSOLES TEL: 800.447.2257 WEB: winsted.com EMAIL: info@winsted.com PRODUCT FEATURES AND HIGHLIGHTS Laminate with Safeguard Work Surface Spectrum 2 comes standard with our durable laminated

More information

Two Circuit Track Power System IS24 / IS26 / IS28

Two Circuit Track Power System IS24 / IS26 / IS28 Two Circuit Track Power System IS24 / IS26 / IS28 DESCRIPTION Two circuit / single neutral track is an affordable and durable solution that features easy installation. Track system is available in 4, 6,

More information

Power Base AI. Power Base AI. Technical Sheets

Power Base AI. Power Base AI. Technical Sheets Power Base AI Power Base AI Technical Sheets odular Electrical System System Overview Haworth s Power Base AI modular electrical system provides a flexible, reconfigurable power distribution infrastructure

More information

active storage C A D D I E & T RO L L E Y B A S I C S...6 4

active storage C A D D I E & T RO L L E Y B A S I C S...6 4 A C T I V E S TO R A G E O V E RV I E W & F I N I S H E S................6 3 C A D D I E & T RO L L E Y B A S I C S...........................6 4 P L A N N I N G W I T H A C T I V E S TO R A G E.....................6

More information

STORAGE SIN 711-2/3. Pedestal, Lateral File, & Personal Storage Options WORKSURFACES STORAGE SMARTSPACE

STORAGE SIN 711-2/3. Pedestal, Lateral File, & Personal Storage Options WORKSURFACES STORAGE SMARTSPACE SIN 711-2/3 STORAGE Freestanding Storage Maxon Freestanding Storage options incorporate innovative, durable designs that maximize the efficiency of your workspace. Constructed of heavy-duty steel, Maxon

More information

Updated Pricing and Content as of July 1, 2018

Updated Pricing and Content as of July 1, 2018 SIN 711-2/3 STORAGE Freestanding Storage Maxon Freestanding Storage options incorporate innovative, durable designs that maximize the efficiency of your workspace. Constructed of heavy-duty steel, Maxon

More information

Assembly Instructions

Assembly Instructions Assembly Instructions Flat Screen Garage End User & IT Computer Cable Management May 2013 nylon zip-tie #2 (for computer wires) rear-access beam door (open) Figure 1 nylon zip-tie #1 (for #1 motor control

More information

T A B L E O F C O N T E N T S

T A B L E O F C O N T E N T S T A B L E O F C O N T E N T S UNIT 1: INTRODUCTION... 1 X SERIES STORAGE REFERENCE MANUAL FOR CANVAS... 1 CANVAS DISCLAIMER... 1 X SERIES STORAGE EXTENSION TAB... 1 MAIN SECTIONS OF THE X SERIES STORAGE

More information

Vertiv VR Rack 1.0 GENERAL

Vertiv VR Rack 1.0 GENERAL 1.1 SUMMARY Vertiv VR Rack Guide Specifications 1.0 GENERAL This specification defines the mechanical characteristics and requirements for the Vertiv VR Rack. A series of adaptive and scalable electronic

More information

25DTP412 12'5" Tele-Powr Pole. Features Made in USA. Material, Color, and Finish. Dimensions and Weight

25DTP412 12'5 Tele-Powr Pole. Features Made in USA. Material, Color, and Finish. Dimensions and Weight 25DTP412 12'5" Tele-Powr Pole Wiremold/Legrand Catalog Number 25DTP412 Manufacturer Wiremold/Legrand Description Tele Power Pole, Factory Wired; Shape Rectangular; 2 Compartment(S); 2 Outlet(S); Outlet

More information

24" D 30" D 24" D 30" D

24 D 30 D 24 D 30 D SIN 711-3 Storage REFERENCE EMERGE PREFIX Freestanding Storage Maxon Freestanding Storage options incorporate innovative, durable designs that maximize the efficiency of your workspace. Constructed of

More information

electrical evolvefurnituregroup.com 125

electrical evolvefurnituregroup.com 125 electrical evolvefurnituregroup.com 125 TECHNICAL INFORMATION STEP-BY-STEP SPECIFICATION 8-WIRE ELECTRICAL SYSTEM Step 1 Determine the location of the source power entering the Panel Run. 1. At the base

More information

Single action door patch fittings

Single action door patch fittings Single action door patch fittings The flexible system for all installation situations. CONTENTS Technical details - 5 Materials and surface finishes Product information Patch fittings / none rebated frame

More information

WIREMOLD Tele-Power Poles

WIREMOLD Tele-Power Poles Bring Wire & Cable Down to Business WIREMOLD Tele-Power Poles Routing power, data, and A/V neatly and simply from up there to down here; that s what Tele-Power Poles are all about. Their sole purpose is

More information

or

or Infinite possibilities for your data center The F-Series TeraFrame T M Cabinet System The F-Series TeraFrame Cabinet System from Chatsworth Products, Inc. (CPI) provides configurable thermal management

More information

Shelving. Power Track Light Shelves 2 Shelf Edge 4 Shelf Standards & Brackets 5 Flexis DisplayMaker Shelving 8

Shelving. Power Track Light Shelves 2 Shelf Edge 4 Shelf Standards & Brackets 5 Flexis DisplayMaker Shelving 8 Shelving Stylmark s shelving products have clean lines that provide an attractive accent to any area. Constructed of aluminum or stainless steel, these elegant framed shelves are available with or without

More information

worksurface supports & accessories

worksurface supports & accessories worksurface supports & accessories WORKSURFACE SUPPORTS PANEL MOUNTED OVERVIEW... 151 WORKSURFACE SUPPORTS PANEL MOUNTED BASICS...... 152 PLANNING WITH SUPPORTS SEMI-SUPPORTED 149 WORKSURFACES..................................

More information

storage for secondary desk

storage for secondary desk storage for secondary desk STORAGE FOR SECONDARY DESK BASICS................ LATERAL FILE FOR SECONDARY DESK CENTER POSITION FILING DRAWER CAPACITIES............................... LATERAL FILE FOR SECONDARY

More information

Knürr Elicon Ergonomic. Modular. Future-proof. Control Room Infrastructure

Knürr Elicon Ergonomic. Modular. Future-proof. Control Room Infrastructure Knürr Elicon Ergonomic. Modular. Future-proof Control Room Infrastructure Knürr Elicon Knürr Elicon VC and VC-E Series 4 Modular Workstation Systems Knürr Elicon Classic 14 Knürr Elicon Accessories 22

More information

TRANSCEND. Table of Contents. Transitional Desks. Transcend Kimball Desks & Accessories. Price List Effective Dates:

TRANSCEND. Table of Contents. Transitional Desks. Transcend Kimball Desks & Accessories. Price List Effective Dates: TRANSCEND Table of Contents Price List Effective Dates: 12.18.17 Revision 03.19.18 See page Statement of Line page 6.2 Planning 6.5 Overview 6.5 Technology Management page 6.6 Integrating with Traxx &

More information

Cable Management Solid Cherry Wood Durable Desk Inlay Integrated Power Strip Versions: L Shaped Right. L Shaped Right

Cable Management Solid Cherry Wood Durable Desk Inlay Integrated Power Strip Versions: L Shaped Right. L Shaped Right Doc. 921-0001-00-00-A Artistic Desk Full, Right Artistic Desk Full, Left The Computer Desk that Hides your Wires and Cables The Artistic Computer are designed with artistic shaped legs that provide a clean,

More information

CATALOG NUMBER PROJECT W2 TRACK AND COMPONENTS

CATALOG NUMBER PROJECT W2 TRACK AND COMPONENTS CATALOG NUMBER TYPE PROJECT W2 TRACK AND COMPONENTS Description W2 120V or 277V Track system provides two separate 20 AMP circuits and two neutrals. Each circuit can be independently switched. Fully polarized

More information

2.7 UNDER-CARPET WIREWAY

2.7 UNDER-CARPET WIREWAY 2.7 UNDER-CARPET WIREWAY U.S. List Pricing SO SUBTLE IT VIRTUALLY DISAPPEARS Connectrac 2.7 Under-Carpet Wireways. Completely concealed by carpet tile, they are Connectrac s lowest, sleekest, most invisible

More information

PRELIMINARY. CR Series. Ceiling Rack Systems with AmbiTILT Equipment Loading

PRELIMINARY. CR Series. Ceiling Rack Systems with AmbiTILT Equipment Loading 1/6 CR Series Ceiling Rack Systems with AmbiTILT Equipment Loading General Description AtlasIED, the manufacturing leader of ceiling mounted loudspeakers introduces the new CR Series ceiling-mounted equipment

More information

Medina Laminate Series

Medina Laminate Series Medina Laminate Series MEDINA DESK SYSTEM Laminate Options: Gray Steel-LGS, Mahogany-LMH, Mocha-LDC, Textured Sea Salt-TSS and Textured Brown Sugar-TBS. CARB Compliant: Core materials comply with Phase

More information

Series 575. Vertical Flow Modular Softwall Cleanroom. Series 575 Vertical Flow Modular Softwall Cleanroom

Series 575. Vertical Flow Modular Softwall Cleanroom. Series 575 Vertical Flow Modular Softwall Cleanroom Series 575 Vertical Flow Modular Softwall Cleanroom S O L U T I O N S The Series 575 softwall cleanroom is a cost-effective method of providing quality particulate control in a softwalled enclosure. The

More information

SECTION WIRING DEVICES

SECTION WIRING DEVICES PART 1 - GENERAL... 1 1.1 RELATED DOCUMENTS... 1 1.2 SUMMARY... 1 1.3 DEFINITIONS... 1 1.4 REFERENCES... 2 1.5 SUBMITTALS... 2 1.6 QUALITY ASSURANCE... 2 1.7 COORDINATION... 2 PART 2 - PRODUCTS... 2 2.1

More information

Privacy Wall - Power & Data Box (Field Installed) Modular & Hardwire Versions

Privacy Wall - Power & Data Box (Field Installed) Modular & Hardwire Versions Privacy Wall - Power & Data Box (Field Installed) Modular & Hardwire Versions If you have a problem, question, or request, call your local dealer, or Steelcase Line 1 at 888.STEELCASE (888.783.3522) for

More information

POLE DISPLAY SOLUTIONS & ACCESSORIES

POLE DISPLAY SOLUTIONS & ACCESSORIES & ACCESSORIES Pole Display Solutions Litho poles and bases are an excellent and versatile way to highlight a message. Pole dimensions are in lengths from two to six feet and 1 to 1-3/4 inch diameters.

More information

PHYSICAL INFRASTRUCTURE QUICK SKU FINDER

PHYSICAL INFRASTRUCTURE QUICK SKU FINDER PHYSICAL INFRASTRUCTURE QUICK FINDER Simplified Connectivity Simplified Connectivity combines our technical support services, products, and industry leading customer advocacy to create a comprehensive

More information

Modular Workstations. Dimension 4 : Your Smart Choice for Versatile and Adaptable Workstations. Building Blocks for Infinite Productivity Solutions

Modular Workstations. Dimension 4 : Your Smart Choice for Versatile and Adaptable Workstations. Building Blocks for Infinite Productivity Solutions Modular Workstations Dimension 4 : Your Smart Choice for Versatile and Adaptable Workstations Building Blocks for Infinite Productivity Solutions IAC s Dimension 4 modular technology solves your application

More information

TV & Office Solutions by equip solutions with a high value of benefit

TV & Office Solutions by equip solutions with a high value of benefit TV & Office Solutions by equip solutions with a high value of benefit The brand equip stands for a product development driven by quality management and continuous adjustments to the requirements of the

More information

Power Channel And Power Unit

Power Channel And Power Unit 478086489 R 3m/10', Inc. Grand Rapids, MI 49501 U.S.. 1-888-783-3522 onference Table Top Options Power/ommunications Power hannel nd Power Unit TEHNOLOGY OVERS Power Unit Power hannel TOOLS Lufkin Tape

More information

BUSINESS FURNITURE PARTS LIST & SPECIFICATIONS EFFECTIVE: JANUARY 1, 2012

BUSINESS FURNITURE PARTS LIST & SPECIFICATIONS EFFECTIVE: JANUARY 1, 2012 BUSINESS FURNITURE PARTS LIST & SPECIFICATIONS EFFECTIVE: JANUARY 1, 2012 415 Finchdene Square Scarborough, Ontario. Canada M1X 1B7 Tel: 416-298-9137 Fax: 416-298-9458 Email:calstone@calstoneinc.com www.calstoneinc.com

More information