RPC-600/610. Industrial Chassis USER' Manual

Transcription

1 RPC-600/610 Industrial Chassis USER' Manual

2 RPC-600/610 Industrial Chassis USER' Manual Headquarters (China): Shenzhen: Beijing: Shanghai: Chengdu: Shenyang: Xi an: Wuhan: TianJin: Singapore: Website:

3 Shenzhen NORCO Intelligent Technology CO.,LTD. RPC-600/610 Industrial Chassis

4 Trade Name:Shenzhen NORCO Intelligent Technology CO., LTD.. Model Name:RPC-600/610 Responsible Party:Shenzhen NORCO Intelligent Technology CO.,LTD. Equipment Classification:FCC Class B Subassembly Type of Product:Industrial Chassis Manufacturer:Shenzhen NORCO Intelligent Technology CO.,LTD.

5 Content Chapter 1 Product Introduction Overview Specification Backplane information Power optional Ordering Information...3 Chapter 2 Installation Guide Structure view Outline Dimensions Front Panel Diagram Back Panel Diagram Internal Structure Diagram System Setup Removing the cover Install HDD Replacing the filter Back window FAN Install(optional)...13 Appendix...15 Appendix A: Backplanes...15 Appendix B: Safety Instructions...22

6 Packing List Thank you very much for choosing our products, completely check your package as the following item checklist first, if you find any component missing or damaged, please contact your retailer. RPC-600/610 Key Power cable (BS) 5 to 3 tray Air Filter Screw Flexible adjust card clamp Manual 1pcs 1set 1pcs 1set 1bag 1pcs 4pcs 1pcs

7 Chapter 1 Product Introduction

8 Chapter 1 Product Introduction 1.1 Overview RPC-600/610 is an improved 4U 19 rackmount chassis, It is fully compatible with P3/P4 commercial mainboard; embedded industrial backplane; the Drive Disk Enclosure contains 1x3.5 drive bays and 3x5.25 driver bay. Front panel with dual-usb port. Built-in high-speed air-intake fan supports abundant cooling and streamline ventilation. It is easy to clean. The bracket bay features anti-vibration capability. Can be widely applied to many fields, such as industrial control, CTI, DVR etc. 1.2 Specification Physics Construction: high strength 1.2mm carbon structural steel, meet FCC and CE Class B spec Technics: surface machining of spray-paint, high temperature firing Color: White/Black (Optional) Dimension: 488mm 471mm 177mm (W D H) Chassis Configuration:4U,RackMount,meet the EIARS-310C standards Drive bay: 1x3.5 drive bays, 3x5.25 driver bay Cooling FAN: 1x8025 fan with air filter on front panel Control: Front reset button, power switch and keyboard-lock Port: 2xUSB port Backplane support: Industrial Backplane or ATX PC board Indicators: LEDs for power On/Off and HDD Power: AT/ATX (Optional) Vibration: 1 Grms (5 ~ 500 Hz) Shock: 10G (with 11 ms duration, half sine wave) Applications: industrial control, CTI, DVR etc. 1

9 Environment Temperature: (-4-140F) Humidity: 40 C, (no condensing) Acoustic Noise: Less than 56 db sound pressure at 5 ~ 28 C (41 ~ 82 F) 1.3 Backplane information Model system slots Dimension(mm) PBP-08P4 single 4PCI/2 PICMG/2 ISA PBP-09P6 single 6PCI/2 PICMG/1 ISA PBP-13L4 single 4PCI/2 PICMG/7 ISA PBP-14I single 14ISA PBP-14P4 single 4PCI/2 PICMG/8 ISA PBP-15P7 single 7PCI/2 PICMG/6 ISA PBP-15P12 single 12PCI/3 PICMG Power optional Model PWR-300 PWR-350 Characters Power Input Output 180~ +3.3V@20A,+5V@20A 300W 260VAC 47~ +12V1@12A,+12V2@12A, 63Hz -5V@0.5A,-12V@0.8A 180~ +3.3V@28A,+5V@25A 350W 260VAC 47~ +12V1@15A,+12V2@15A, 63Hz -5V@0.1A,-12V@0.8A 2

10 1.5 Ordering Information Model Color Back Window RPC-600/610 Black/White AT/ATX 3

11 Chapter2 Installation Guide

12 Chapter 2 Installation Guide 2.1 Structure view Outline Dimensions RPC-600 dimensions: 4

13 RPC-610 dimensions: Front Panel Diagram RPC-600 Exterior Front Panel: 1: Chassis-lock 2: Power LED 3: HDD LED 5

14 RPC-610 Exterior Front Panel: 1: Chassis-lock 2: Power LED 3: HD LED RPC600/610 Internal Front Panel: 1: Screw for open Air Filter 2: Power LED 3: HD LED 4: Drive bay 5: Power Button 6: Reset Button 7: Dual-USB Port 6

15 2.1.3 Back Panel Diagram RPC-600/610 ATX Back Window(Configurable PC mainboard): 1: Screw for Top Cover 2: Cooling Hole 3: FAN Assemble (for 60mm FAN) 4: ATX I/O RPC-600/610 Back Window (Configurable Industrial Backplane): 1: Screw for Top Cover 2: FAN Assemble position (for 60mm FAN) 3: Expansion (PCI/ISA/PICMG) 7

16 2.1.4 Internal Structure Diagram RPC-600/610 Internal Structure: : FAN power connect cable 2: CPU card slot 3: Flexible adjust card clamp 4: Drive enclosure 5: Shock-resistant Screw 6:Hold-Down Clamp 6 8

17 2.2 System Setup The following procedures are provided to assist you in installing drives, plug-in cards and the hold-down clamp in to the RPC-600/ Removing the cover Removing the chassis cover,place it in the flat surface, so as to avoid causing scratches on the spraying surface of chassis cover. 1: Please use screwdrivers to twist both of host cover's sides of the screw by the direction of anti-clockwise. 2: Seize the both sides of host cover, pull backwardly. 3: Take out the host cover and place it in a safe place to avoid scratches Install HDD After removing host cover,you can easily install disk drivers You should follow these steps before installing disk drivers: 1: Twist off the screws on fixed Drive Disk Enclosure with screwdriver, Place it inside the container. 2: Take the Drive Disk Enclosure Out of chassis with gloves, put it in the smooth platform, preferably where is foam pad avoid knocking and stumbling FDD Install: Place FD into a 3.5-inch driver's location (At the bottom of driver), Fix FD with screws on the both sides of Drive Disk Enclosure. 9

18 HD Install: Firstly fix hard disk and 5 to 3 tray, and then put it into a 5.25-inch driver's location, Fix 5 to 3 tray with screws on the both sides of Drive Disk Enclosure. (optional)firstly fix hard disk and HDD Shock-Resistant tray,and then put it into a 5.25-inch driver's location,fix HDD Shock-Resistant tray with screws on the both sides of Drive Disk Enclosure. 10

19 CD-ROM Install: Place CD-ROM into a 5.25-inch driver's location, Fix CD-ROM with screws on the both sides of Drive Disk Enclosure 5HD Expand Install (optional): 1: Fix hard disk and HDD Shock-Resistant tray with Shock-Resistant Screw. 2: Fix the other 5 hard disks with trays and add them to Drive Disk Enclosure, tighten the screws, and put them inside the chassis Backplane and CPU Card Install 1: Open Hold-Down Clamp, Choose the proper backplane according to requirement, and Fix the backplane inside the chassis. 2: Insert the CPU to be used into the chooses backplane (PC mainboard can be straightly fixed inside the chassis) 3: Put down Hold-Down Clamp, adjust to the purpose height so as to held the motherboard steady 11

20 Flexible adjust card clamp Can adjust from top to bottom. Twist off the screw on flexible adjust card clamp, flexible adjust card clamp can move back and forth Replacing the filter Replacing the filter complied steps following: 1: Remove the screws located on the left side of the filter cover. Gently but firmly pull the cover from the chassis. 12

21 2: Remove the filter and replace it with a new one. 3: Reinsert the filter and replace the cover onto the chassis. Note: To avoid filter effect's declining, clean the filter per month Back window FAN Install(optional) If the user chooses the RPC-600/610-ATX, 1 set of 60mm 60mm 6020 fan can be installed at the back window, so as to keep the chassis cool and clean, and avoid any damage from high temperature. 2x6020 FAN location 1: Twist off the screw at the back cover of chassis, remove the chassis cover and put it in a safe place. 2:Put a complete set ( 2 fans, sharing a power connector ) of 60mm 60mm 6020 fan 13

22 into the position to be installed in the back window, fix the fan with screws in the rear window 3: After installing fan, please plug in the fan power connector 14

23 Appendix

24 Appendix A: Backplanes Model: PBP-08P4 Dimensions: 270.7mm 191.7mm Appendix Description: Slots 8 15

25 PCI 4 PICMG 2 ISA 2 Power supply AT/ATX Model: PBP-09P6 Dimensions: 270mm 191mm Description: Slots 9 AT Power Connector ATX Power Connector PCI Slot Standby Switch Keyboard Port Power Switch ISA Slot 6Pin Power Connector Screw Hole PICMG Slot 16

26 PCI 6 PICMG 2 ISA 1 Power supply AT/ATX Model: PBP-13L4 Dimensions: 308mm 270mm Screw Hole ISA Slo t AT Power Connector PICMG Slot 6Pin Po we r Co nne c to r Description: Slots 13 17

27 PCI 4 PICMG 2 ISA 7 Power supply AT/ATX Model: PBP-14I Dimensions: mm mm ISA Slot Keyboard Port Screw Hole AT Power Connector ATX Power Connector Standby Switch 6Pin Power Connector Power Switch Description: Slots 14 ISA 14 Power supply AT/ATX 18

28 Model: PBP-14P4 Dimensions: 323mm 270mm Description: Slots 14 PCI 4 PICMG 2 ISA 8 Power supply AT/ATX 19

29 Model: PBP-15P7 Dimensions: 317mm 270mm Description: Slots 15 PCI 7 PICMG 2 ISA 6 Power supply AT/ATX 20

30 Model: PBP-15P12 Dimensions: 317mm 270mm Description: Slots 15 PCI 12 PICMG 3 Power supply AT/ATX 21

31 Appendix B: Safety Instructions 1: Read these safety instructions carefully. 2. Keep this installation reference guide for later reference. 3. Disconnect this equipment from any AC outlet before cleaning. Do not use liquid or spray detergents for cleaning. Use a damp cloth. 4. For pluggable equipment, the power outlet must be installed near the equipment and must be easily accessible. 5. Keep this equipment away from humidity. 6. Put this equipment on a reliable surface during installation. Dropping it or letting it fall could cause damage. 7. The openings on the enclosure are for air convection. Protect the equipment from overheating. Do not cover the openings. 8. Make sure the voltage of the power source is correct before connecting the equipment to the power outlet. 9. Position the power cord so that people cannot step on it. Do not place anything over the power cord. 10. All cautions and warnings on the equipment should be noted. 11. If the equipment is not used for a long time, disconnect it from the power source to avoid damage by transient over-voltage. 12. Never pour any liquid into an opening. This could cause fire or electrical shock. 13. Never open the equipment. For safety reasons, the equipment should be opened only by qualified service personnel. 14. If any of the following situations arises, get the equipment checked by service personnel: a. The power cord or plug is damaged. b. Liquid has penetrated into the equipment. c. The equipment has been exposed to moisture. d. The equipment does not work well, or you cannot get it to work according to the installation reference guide. e. The equipment has been dropped and damaged. f. The equipment has obvious signs of breakage. 15. Do not leave this equipment in an uncontrolled environment where the storage 22