IC-9039: Multimedia Interface.- NEW PEUGEOT 407 / 607

Transcription

1 IC-9039: Multimedia Interface.- NEW PEUGEOT 407 / 607 This interface is to be used in cars with 12V negative ground only. Depending on the type of installation to be performed in your Peugeot 407/607, you will need to cose between these two options: Option A) In case you want to connect a Navigation system only, you will only need to use our Peugeot RGB board. In this case you can t install any rear view camera or external video source. Option B) Peugeot 407/607 has an auxiliary input, but it does not work with the car in motion. To install a rear view camera or a DVD player and see the picture in motion, you will need to install both the Universal RGB Interface and the Peugeot RGB board. Compruebe las piezas suministradas dependiendo del tipo de instalación que se vaya a realizar, y tenga en cuenta siempre esta información a la hora de hacer su pedido. INTERFACE PARTS This interface is supplied with the following parts. Please check that you have received a full set. If there is any part missing, please contact us immediately. OPTION A, FOR INSTALLATION OF NAVIGATION ONLY RGB INTERFACE FCC CABLE (LCD IN/OUT) NOVOSONIC LA PLANA, S.L IC-9039

2 IR CABLE RGB CABLE REMOTE OPTION B, FOR MULTI-SYSTEM (NAVIGATION, DVD, TV, CAMERA, ETC) RGB INTERFACE RGB BOARD POWER CABLE FCC CABLE IN/OUT RGB INPUT NAVI IN RGB OUTPUT REMOTE AUDIO SEL. OUT IR CABLE NOVOSONIC LA PLANA, S.L IC-9039

3 Safety Advices before Installation Caution: Installation requires special knowledge and should be done by trained personnel. Please read these instructions carefully before you start to work. Please work with caution and patience. Use suitable and recommended tools only and handle all parts with special attention. Follow the regulations concerning the vehicle electric system. Remove the ignition key before you start the installation. Take care that no electric consumers are still switched on. Installation may only be done in idle status. Please pay attention to the car manufacturer s requirements. This interface is to be used in cars with 12V negative ground only. 2) Connections INSTALLATION A LCD OUT: Connect to monitor. LCD IN: Connect to PDB board located behind the monitor. NAVI: Connect to Navigation. 1.- BLUE Blue Signal 2.- RED Red Signal 3.- GREEN---- Green Signal 4.- BROWN Synchrony 5.- BLACK --- GND 6.- RED Positive ACC (See page 11) 7/8.- N. C. INSTALLATION B NOVOSONIC LA PLANA, S.L IC-9039

4 ON INSTALLATIONS WHERE BOTH PEUGEOT RGB BOARD AND RGB INTERFACE ARE USED, THE MICROCHIP ON THE BOARD MUST BE REMOVED RGB Interface Installation - IR Cable: Receiver for remote control -Power cable 1- GND (BLACK) 2- Source (ORANGE) NOVOSONIC LA PLANA, S.L IC-9039

5 3- Safe (GREEN) 4- N.C. 5- ACC (RED) 6- Reverse lamp (GREY) -RGB IN 1- R (red) 2- G (green) 3- B (blue) 4- SYNCHRONY (white) 5- GND (black) - RGB OUT CONNECT ONE END TO THE RGB INTERFACE - AUDIO-SEL Cable AND OTHER END TO PEUGEOT RGB BOARD 1- Audio 1 (WHITE) 2- Audio 2 (ORANGE) 3- Audio 3 (BROWN) 4, 5, 6- N.C. NOVOSONIC LA PLANA, S.L IC-9039

6 - NAVI IN Cable 1- R (red) 2- G (green) 3- B (blue) 4- SYNCHRONY (white) 5- GND (black) 6, 7- N.C. -Video Inputs (CVBS IN) -Video 1 -Video 2 -Video 3 -Rear View Camera Input -DIP SWITCH SETTINGS It is possible that some units have misprinted signs. Switch DOWN means OFF, switch UP means ON. 1.- NAVI IN 2.- VIDEO INPUT VIDEO INPUT VIDEO INPUT CAMERA INPUT 5, 6, 8.- OPTION. -These 2 connectors will have no use: NOVOSONIC LA PLANA, S.L IC-9039

7 3) Removal of the front monitor 1.- Remove the dashboard frame 2.- Remove the four screws 3.- Disconnect the wires and remove the monitor 4) Monitor NOVOSONIC LA PLANA, S.L IC-9039

8 1.- Remove the cover Remove the three screws Remove the back cover of the monitor 2.- Disconnect the cables and remove the PCB board 3.- Connect the FCC Cables IN and OUT Remove original FCC cable Connect FCC cable (OUT) to monitor Connect FCC cable (IN) to PCB board NOVOSONIC LA PLANA, S.L IC-9039

9 4.- Connect the FCC to the Peugeot RGB board 5A.- In A option installations, connect IR and RGB cables to the board, as shown in the picture. 5B.- In B option installations, connect IR and RGB cables to the board, as shown in the picture. The RGB cable must be connected to both RGB Interface and RGB Board, IR cable must be connected to the RGB Interface. REMEMBER: IN THIS INSTALLATION, THE MICROCHIP ON THE PCB BOARD MUST BE REMOVED NOVOSONIC LA PLANA, S.L IC-9039

10 6.- How to pass the cable You will need to make a hole. Place the monitor in its original position. NOVOSONIC LA PLANA, S.L IC-9039

11 5) Location of ACC and GND connections You will find the following connections at the rear of the radio. ACC You will find ACC connection under the steering wheel. 607: Brown 407: Grey FOR SAFETY REASONS, YOU MUST CONNECT A FUSE (15A) TO ACC. Technical Support If you experience any problems while installing this device and you cannot find the solution here, please don t hesitate to contact us: Telephone: comercial@novosonic.es Fax: admonex@novosonic.es NOVOSONIC LA PLANA, S.L IC-9039