ET-BASE AVR ATmega64/128

Transcription

1 ET-BASE AVR ATmega64/128 ET-BASE AVR ATmega64/128 which is a Board Microcontroller AVR family from ATMEL uses MCU No.ATmega64 and ATmega128 64PIN. Board ET-BASE AVR ATmega64/128 uses MCU s resources on board mainly and arranges Pin I/O as Port PA, PB, PC, PD, PE, and PF, Port ET-CLCD, and including Port for downloading Program, it makes us more convenient to apply for various project works. Moreover, there s addition circuit Driver RS-232, so we can use RS-232 Serial Port Communication easily and conveniently. Specifications Use MCU AVR family No.ATmega64, ATmega128 from ATMEL 8BIT to be permanent MCU on board, and XTAL 16 MHz. Moreover, this MCU has other interesting specifications as following; - Flash Memory 64 K Bytes for ATmega64 and 128 K Bytes for ATmega128, and RAM 4 K Bytes - EEPROM 2K Bytes for ATmega64 and 4 K Bytes for ATmega128, in this case, we can erase and re-write data more than 100,000 times. - Maximum 53 I/O Pins - Circuit SPI Communication 1 Channel, I2C 1 Channel, Programmable Serial USARTs 2 Channel - ADC 10-Bit 8 channel - Timers/Counter 8-Bit 2 Channel, Timers/Counter 16-Bit 2 Channel, 8-Bit PWM 2 Channel, Watchdog Timer, Real Time Counter 6 I/O Port 10PIN; PA,PB,PC,PD,PE, and PF Port ISP LOAD for program MCU (must use with ET- AVR ISP or ISP Programmer that has the same type of Pin arrangement). Line Driver for RS232 Serial Port Communication 2 Channel; one Port for interfacing with Signal PE0(RXD0) and PE1(TXD0) and other one Port for interfacing with Signal PD2(RXD1) and PD3(TXD1), in this case, we can test connection of circuit RS232 Serial Port Communication easier. Circuit for connecting with Character LCD Display Monitor (ET-CLCD) and VR for contrasting brightness of LCD, in this case, it is ETT CO.,LTD -1-

2 interfaced circuit with LCD as 4 Bit Interface type. Circuit Regulate +5V/1A for supplying power into circuit of LCD Display Monitor and I/O components for using with Power Supply that is not much than +5V and red LED. PCB Size 8 x 6 cm. Structure of Board No.1 is MCU No.ATmega64 or ATmega128 AVR family from ATMEL. No.2 is Switch RESRT to reset operation of MCU. No.3 is Crystal 16 MHz. No.4 is Resistor to contrast brightness of LCD. No.5 is PORTC 8 Bit; PC0-PC7. No.6 is Port ISP LOAD to download Hex File into MCU. No.7 is Port ET-CLCD to connect with Character LCD as 4 Bit type. ETT CO.,LTD -2-

3 No.8 is PORTD 8 Bit; PD0-PD7. No.9 is PORTB 8 Bit; PB0-PB7. No.10 is PORTE 8 Bit; PE0-PE7. No.11 is PORTF 8 Bit; PF0-PF7. No.12 is PORTA 8 Bit; PA0-PA7. No.13 and 14 are Connector RS232 for general usage. No.15 is LED Power to display status of Power Supply +5VDC. No.16 is Connector Power Supply. Connectors For Connector Port I/O from MCU, it is designed and is provided through 6 Connectors IDC-Header 10PIN (2X5); PA, PB, PC, PD, PE, and PF respectively. Each Connector consists of Signal I/O that is connected directly from Pin MCU. The external connecting point of board is shown as following; Connector Power Supply of Board Connector PORTA 8 Bit; PA0-PA7 Connector PORTB 8 Bit; PB0-PB7 Connector PORTC 8 Bit; PC0-PC7 Connector PORTD 8 Bit; PD0-PD7 Connector PORTE 8 Bit; PE0-PE7 Connector PORTF 8 Bit; PF0-PF7 Connector ET-CLCD for interfacing with LCD Character type Connector RS232 2 Channel; one channel for interfacing with Signal PE0(RXD0) and PE1(TXD0) and other one channel for interfacing with Signal PD2(RXD1)and PD3(TXD1), in this case, we can test connection of circuit RS232 Serial Port Communication easily. Connector ISP LOAD for downloading HEX File into MCU ETT CO.,LTD -3-

4 Port PA 8 Bit Port PB 8 Bit Port PC 8 Bit ETT CO.,LTD -4-

5 Port PD 8 Bit Port PE 8 Bit Port PF 8 Bit ETT CO.,LTD -5-

6 Port ISP LOAD Picture displays circuit for connecting with ISP LOAD. Port ET-CLCD: It is used with Character Type LCD for connecting as 4 Bit type. It uses signal from Port PG and PD (PD7) to connect with LCD. In this case, we must use the signal name to be reference and must interface all 14 cables corresponding with the truly name on the Connector. ETT CO.,LTD -6-

7 GND +VCC VO RS RW EN D0 D1 D2 D3 D4 D5 D6 D7 Picture displays Pin Arrangement of Character LCD Standard. Port RS232 2 Channel: It is used 1 Channel to connect with Signal PE0(RXD0) and PE1(TXD0) and other one Channel for interfacing with Signal PD2(RXD1) and PD3(TXD1). ETT CO.,LTD -7-

8 Picture displays circuit for connecting with RS232. To Download Hex file into MCU It is necessary to use ET-AVR ISP or other types of ISP Programmer such as AVRISP from ATMEL to download Hex File into MCU AVR family from ATMEL, especially procedure of Serial Programming Type. If we use ET-AVR ISP, we must download Hex File through Parallel Port of computer and must use it with ET-CAP10P from ETT and Software PonyProg2000 program that can use with ETT Board well. User can learn general usage from menu HELP by self, in this case, we will only mention procedure to setup program PonyProg2000 for using with all versions Board AVR family from ETT. ETT CO.,LTD -8-

9 Structure of Board ET-AVR ISP No.1 is Port for connecting with ET-CAP10P from ETT to program Hex File into MCU. No.2 is LED PGM (GREEN) to display status of programming or to download Hex File into MCU. No.3 is LED PWR (RED) to display status of supplying power on board. No.4 is Port for connecting with Board Target that can program Hex File into Board ET-AVR STAMP ATmega64 by inserting Board ET-AVR ISP at the position of Port ET-PSPI. Pin arrangement is shown as in the picture below; Pin Position Signal s Name 1 MOSI 2 VCC 3 Disable 4,6,8,10 GND 5 RESET 7 SCK 9 MISO ETT CO.,LTD -9-

10 To Connect Component for Programming Hex File We must use ET-CAB10PIN and Program PonyProg2000 to program Code (Hex File) into AVR MCU. We must interface ET-CAB10PIN with Port Printer and then set Jumper for using Program PonyProg2000. Next, interface cable Download at the Connector ET-PSPI Download of Board, then supply power into board. We should take off all external components that interface with Port PB before programming code Hex File. The feature of connection is shown as in the picture below. (LEFT) ET-CAP10P V2.0 (RIGHT) ET-CAP10P V1.0 Picture displays Set Jumper and interface cable Download of ET-CAP10P for using with AVR. ETT CO.,LTD

11 Picture displays the connection ET-AVR ISP with ET-BASE AVR ATmega64/128, in this case, Pin position of one board must be corresponding with other one board. To program Board ET-BASE AVR ATmega64/128 by using Program PonyProg2000 Program Ponyprog2000 is a program for downloading data Hex File into CPU AVR family through Serial Programming Type. This method can be used with all versions of board AVR family from ETT. User can learn general usage from menu HELP by self, in this case, we will only mention procedure to setup program PonyProg2000 for using with all versions Board AVR family from ETT. Be carefully, in case of using CPU AVR family No.ATmega64 because internal structure has many Fuse Bits to configure condition of CPU operation. These Fuse Bits are effect on downloading as Serial Programming Type. In case of selecting Fuse Bit incorrectly, we can not program CPU by Serial Programming Type. To solve this problem is modifying Fuse Bit of CPU by using Parallel Programmer first and then we can use it as usual. If we program CPU AVR family with ETT Board and use Program PonyProg2000, we must configure Option of program as following; ETT CO.,LTD

12 1. Configure Setup Interface Setup as following. - Select I/O Port to be Parallel and then select format of programming to be Avr ISP I/O. - Select Printer Port as truly usage such as LPT1 in case of using Printer Port LPT1. - No select in the part of Polarity Control Line. - Only setup program for the first time usage. 2. Command Program PonyProg200 to calculate the suitable speed for sending signal into CPU, click Setup Calibration. ETT CO.,LTD

13 - We command to Calibration only one time when we use program in the first time. 3. Select CPU number; click Device AVR Micro such as Atmega Select Command Security and Configuration Bits, if it is other AVR number, can configure Fuse Bit as required. User can learn more detailed of Fuse Bit from Data Sheet of CPU by self. Be carefully, if using with ATmega64, we must configure Fuse Bit correctly otherwise we can not program CPU through Serial Programming Type, we can configure Fuse Bit as following; ETT CO.,LTD

14 Picture displays configuration of Fuse Bit for using with CPU No.ATmega64. The Fuse Bit s Meaning of ATmega64 If select or tick [ ] sign in front of which Fuse Bit, it means that we configure the Fuse Bit to be 0 or Command to program Fuse Bit. If not select or tick [ ] sign in front of which Fuse Bit, it means that we configure Fuse Bit to be 1 or Command to not program Fuse Bit. The Fuse Bit s meaning of ATmega64 that is effect on Serial programming SPIEN: It is Serial Programming Enable Bit. We must always program this Fuse Bit because we can program CPU through In-System Serial Programming. Generally, it is configured by manufacturer and can not be erased or modified by Mode Serial Programming. If CPU is programmed by Parallel Programming, do not forget to command this Fuse Bit. OCDEN and JTAGEN: We use both Fuse Bit to debug operation of MCU and program through JTAG Interface and must use with AVR JTAG Debugger. If we do not use this Fuse Bit for operation, it is necessary to select both Fuse Bits. CKOPT: It is Oscillator Option Bit. If we select this Fuse Bit, it means that we configure CPU to ETT CO.,LTD

15 run with frequency 16MHz. If we do not select this Fuse Bit, we configure CPU to run with frequency not much than 8 MHz. If we use the standard ETT Board, we use XTAL to be frequency generator. So, we should command this Fuse Bit because CPU can run with frequency XTAL range 1.0MHz-16.0MHz. CKSEL3 0: It is Select Clock Source Bit. We use it to select generator frequency and frequency range for CPU. If using with standard ETT Board, must select External Crystal 1.0MHz-16.0MHz but if we select other value, it makes operation of program error. Remember, if we select generator frequency incorrectly such as External Clock or External RC Oscillator, it makes CPU can not run because we do not interface external Clock and we can not program CPU through Serial Programming Type. We can solve this problem by modification Fuse Bit of CPU to be External Crystal. Generator Frequency AVR Atmega64 To Configure Fuse Bit of CKSEL[3 0] (0=Program,1=Un-Program) External Crystal/Ceramic Resonator External Low Frequency Crystal 1001 External RC Oscillator Calibrated Internal RC Oscillator External Clock 0000 Picture displays the selection generator frequency from Fuse Bit CKSEL [3 0]. ETT CO.,LTD

16 NOTE: - Default value = 1. It means that not program Fuse Bit and not tick any mark [ ] in front of Fuse Bit name. - Default value = 0. It means that command to program fuse Bit and must tick mark [ ] in front of Fuse Bit s name. - Should program Fuse Bit of CKOPT to run with frequency range 1.0MHz-16.0MHz. - Do not command to program Fuse Bit of CKSEL[3..0] because the operation will be error. For example, if we program all Fuse Bit of CKSEL[3..0] to be 0, after program PonyProg200 has already written default value of Fuse Bit into CPU completely, we can not use CPU with ETT Board and can not program through Serial Programming Type. If we program all Fuse Bit of CKSEL[3..0] to be 0, it configures CPU to run with External Clock, so External Crystal stops running and CPU wait for receiving External Clock only but ETT Board use only External crystal. So, we must modify Fuse Bit of CPU by using Parallel first, and then we can use CPU as usual. - Fuse Bit s Position of Lock[2..1] cab be configured as required. 5. Select Command Program Option as following; ETT CO.,LTD

17 6. Open Hex File that we want to program into CPU, click File Open Program (FLASH) File and then assign name and address of Hex File. ETT CO.,LTD

18 7. Start to program data into CPU, click Command Program. Then program will run as downloaded 5 Commands as following; Load File Erase Write Program memory (FLASH) and Write Security and Config Bits respectively. In this case, we must wait for program finished completely. After programming completely, CPU will start operation as downloaded data in program instantly. ETT CO.,LTD

19 The basic procedure to check if can not download program If there s error in step of programming, we can check the problem as following; Read User s Manual of Board and User s Manual of Download program AVR by using Program Ponyprog2000 well before using board. Check connection of cables and for downloading program PonyProg2000 must use with Cable Download version ET-CAP10PIN from ETT. We must set Jumper to be PonyProg correctly (can see more detailed from page 9). Check Power Supply of Board. Check default values of program for downloading Program PonyProg2000. Check signal from PORT-PB of CPU is interfaced with external component while downloading or not. For example, it is interfaced with LED or interfaced with other circuit while downloading data. Should not interface Cable RS232 with Port RS-232- CH0 because SPI Programming of ATmega64 uses Pin with RS232 (RXD0, TXD0). ETT CO.,LTD

20 Example with AVR Studio 4 An Example with AVR Studio 4 We use AVR Studio 4 for writing Assembly Language Program because ATMEL Co., Ltd. gives it to customer without any charge and we can download this program free from websit : However, ETT Co., Ltd. provides this program in our CD-ROM. It is program AVR Studio 4 Version 4.12 and proceeding to use this program is; 1. Open program AVR Studio, it will display window of Welcome to AVR Studio and then click New project to create new project as in the picture. 2. Select Project Type as Atmel AVR Assembler for writing Assembly Language Program and then specify project name in the blank of Project name. Select blank of Create initial file to create Assembly File with Project File, select blank of Create folder to create folder for saving project file, and then select directory for saving project file. Lastly, click Finish as in the picture. ETT CO.,LTD -1-

21 Example with AVR Studio 4 3. It will display window of Text Editor for writing program as in the picture. 4. Type example of Assembly Language Program and in the sample, it is program of blinker at PORTB.O. ;******************************************************* ;* Examples Program For "ET-AVR STAMP ATmega64" Board * ;* Target MCU : Atmel ATmega16 * ;* Frequency : X-TAL : 16 MHz * ;* Compiler : AVR Studio 4.12 (AVR Assembler 2) * ;* Create By : ADISAK CHOOCHAN ( * ;* Last Update : 1/September/2005 * ;* Description : Example LED Blink on Portb.0 * ;******************************************************* ETT CO.,LTD -2-

22 Example with AVR Studio 4 ;Connect PB0 to LED1.include "m64def.inc" ;************************ ; Define Register ;************************.def COUNTER1 = R16.def COUNTER2 = R17.def COUNTER3 = R18.def TEMP = R19 ;*********************** ; Define I/O Port,Pin ;***********************.equ LED = 0 ;******************* ; Main Program ;*******************.CSEG.ORG 0 RJMP RESET ;Reset Handle RESET: LDI TEMP,LOW(RAMEND);Initial Stack Pointer OUT SPL,TEMP LDI TEMP,HIGH(RAMEND) OUT SPH,TEMP SBI DDRB,LED ;Config Portb.0 as output MAIN: SBI PORTB,LED RCALL DELAY_200ms CBI PORTB,LED RCALL DELAY_200MS RJMP MAIN ;/****************** ; Delay time ;/****************** DELAY_1ms: LDI COUNTER1,16 DELAY_1ms_1: LDI COUNTER2,250 DELAY_1ms_2: NOP DEC COUNTER2 BRNE DELAY_1ms_2 DEC COUNTER1 BRNE DELAY_1ms_1 RET DELAY_200ms: LDI COUNTER3,200 DELAY_200ms_1: RCALL DELAY_1ms ETT CO.,LTD -3-

23 Example with AVR Studio 4 DEC BRNE RET COUNTER3 DELAY_200ms_1 5. Translate written program, click Menu Instruction of Build Build. After translated program completely without any mistake, it will display a message of 0 errors 0 warning and user can download this HEX File into MCU instantly. ETT CO.,LTD -4-

24 Example with BASCOM-AVR An Example with BASCOM-AVR We use Program BASCOM-AVR for writing BASIC Language Program. MCS Electronics Co., Ltd. has experimental version of this Software and user can download from website : However, ETT Co., Ltd. provides this program in our CD-ROM. It is program BASCOM-AVR Version but user can not compile Source Code greater than 4 kbyte and proceeding to use this program is; 1.Open program CodeVisionAVR C Complier and click Menu Instruction of File New as in the picture. 2. It will display window of Editor for writing program. In the sample, it is a program of blinker at PORTB.O. ETT CO.,LTD -1-

25 Example with BASCOM-AVR '******************************************************* '* Examples Program For "ET-AVR STAMP ATmega64" Board * '* Target MCU : Atmel ATmega16 * '* Frequency : X-TAL : 16 MHz * '* Compiler : BASCOM-AVR * '* Create By : ADISAK CHOOCHAN ( * '* Last Update : 1/September/2005 * '* Description : Example LED Blink on Portb.0 * '******************************************************* 'Connect PB0 to LED1 $regfile="m64def.dat" $crystal= Config Portb=Output 'ATmega16 'X-TAL = 16 MHz 'Config Portc as output Do Loop End Portb.0 = Not Portb.0 Waitms 200 'Convert Portb.0 'Wait 200 ms 3. Save written BASIC Language program, click Menu File Save and specify its File name. Click Save as in the picture. ETT CO.,LTD -2-

26 Example with BASCOM-AVR 4. Select Menu Instruction of Option Compiler Output to assign default value of Output File creation into program BASCOM-AVR. 5. Translate written program, click Menu Instruction of Program Compile. After translated program completely without any mistake, it will display a message as No errors found and user can download this HEX File into MCU instantly. ETT CO.,LTD -3-

27 Example with CodeVisionAVR An Example with CodeVisionAVR We use Program CodeVisionAVR for writing C Language Program. HP InfoTech Co., Ltd. has experimental version of this Software and user can download program from website : However, ETT Co., Ltd. provides this program in our CD-ROM. It is program CodeVisionAVR Version e but user can not compile Source Code greater than 2 kbyte and proceeding to use this program is; 1.Open program CodeVisionAVR C Complier and click Menu Instruction of File New as in the picture. 2. Select File Type as Source to create new C Language File and then click OK as in the picture. ETT CO.,LTD -1-

28 Example with CodeVisionAVR 3. It will display window of Editor for writing program as in the picture. In the sample, it is program of blinker at PORTB.O. //**********************************************/; //*Hardware : ET-AVR STAMP (ATmega64 ) */; //*CPU : ATMEL-ATmega64 */; //* X-TAL : MHz */; //* Filename : Main.C */; //*Complier : CodeVisionAVR V1.24.7d */; //* Last Update : (ETT CO.,LTD) */; //* : */; //*Description : Example LED Blink on Portb.0 */; //**********************************************/; //*CodeVisionAVR Complier Option Setting */; //* Chip type : ATmega64 */; //* Program type : Application */; //*Clock frequency : MHz */; //* Memory model : Small */; //*External SRAM size : 0 */; //* Data Stack size : 1024 */; //**********************************************/; #include <mega64.h> #include <delay.h> // ATmega64 MCU // Delay functions void main(void) { PORTB=0x00; // PB7..0 = 0 DDRB=0x01; // PB0 = Output //Loop Blink LED on PB0 while (1) { PORTB = 0x01; delay_ms(200); PORTB &= 0xFE; delay_ms(200); } } // PB0 = 1 (OFF LED) // Display LED Delay // PB0 = 0 (ON LED) // Display LED Delay ETT CO.,LTD -2-

29 Example with CodeVisionAVR 4. Save C Language Program, click Menu File Save, specify its File name and then click Save as in the picture. 5. Select Menu File New and select File Type as Project to create new project and then click OK as in the picture. 6. Click NO because we do not want HELP to create Project (CodeWizard). ETT CO.,LTD -3-

30 Example with CodeVisionAVR 7. Assign Project Name as required and then click Save as in the picture. 8. Add written C Language File into project, click Add as in the picture. ETT CO.,LTD -4-

31 Example with CodeVisionAVR 9. When it is completely, click OK as in the picture. ETT CO.,LTD -5-

32 Example with CodeVisionAVR 10. Assign default values of project, click Menu Instruction of Project Configure and then assign MCU No. as ATmega64, Crystal as MHz and File Output Format(s) as COF ROM HEX EEP. ETT CO.,LTD -6-

33 Example with CodeVisionAVR 11. Translate written program, click Menu Instruction of Project Make. After translated program completely without any mistake, it will display a message No errors, No warning and then user can download this HEX File into MCU instantly. ETT CO.,LTD -7-