G120 and G120E SoM Datasheet

Size: px
Start display at page:

Download "G120 and G120E SoM Datasheet"

Transcription

1 GHI Electronics, LLC 501 E. Whitcomb Ave. Madison Heights, Michigan Phone: (248) Fax: (248) G120 and G120E SoM Datasheet G120 SoM G120E SoM Where Hardware Meets Software

2 GHI Electronics, LLC Introduction G120 and G120E SoM Datasheet 1 Contents 2 Introduction G120 vs G120E Key Features Example Applications The.NET Micro Framework GHI Electronics and NETMF Pinout Tables G120 Pinout G120E Pinout Reference Design Device Startup Libraries General Purpose Input and Output (GPIO) Analog Input Analog Output Pulse Width Modulation (PWM) Signal Generator Signal Capture Pulse Feedback Universal Asynchronous Receiver Transmitter (UART) Serial Peripheral Interface (SPI) Inter-Integrated Circuit (I2C) Controller Area Network (CAN) Wire Graphics Touch Screen USB Host USB Client File System Networking Ethernet Wi-Fi Point to Point Extended Weak References Configuration Real Time Clock Watchdog Power Control In-Field Update SQLite Database Direct Memory Access Battery RAM EEPROM Runtime Loadable Procedures Design Considerations Required Pins Power Supply Crystals Interrupt Pins Reset SPI Channels Rev

3 GHI Electronics, LLC Introduction G120 and G120E SoM Datasheet 8.7 Ethernet Direct Memory Access Footprints G120 Recommended Footprint G120E Recommended Footprint Soldering the G Oven Reflow Legal Notice Licensing Trademarks Disclaimer Revision History Rev

4 GHI Electronics, LLC Introduction G120 and G120E SoM Datasheet 2 Introduction The G120 SoMs are powerful, low-cost, surface-mount System on Modules (SoM) running Microsoft's.NET Micro Framework. The.NET Micro Framework enables the SoM to be programmed from Microsoft Visual Studio using a USB or serial cable. Programming in a modern managed language, such as C# or Visual Basic, allows developers to accomplish more work in less time by taking advantage of the extensive built-in libraries for networking, file systems, graphical interfaces, and more. A simple two-layer circuit board with a power source and a few connectors can utilize the G120 SoMs to bring the latest technologies to any product. There are no additional licensing or other fees and all the development tools are provided freely. Throughout this document, the G120 SoM and the G120E SoM will be referred to as the G120 and G120E, respectively. When only G120 is listed, the information applies to the G120E as well unless specified otherwise. For more information and support, please see and the product catalog entry. For advanced electrical characteristics and details on the underlying LPC1788FET processor, please consult the processor s datasheet. 2.1 G120 vs G120E The G120 comes in a standard and an extended format. They are not pinout compatible. The below table lists the differences. G120 G120E Processor NXP LPC1788FET180 NXP LPC1788FET208 Package 91 pin surface-mount module (SMT) 105 pin surface-mount module (SMT) Dimensions 26.7 x 38.1 x 3.5 mm x 39.4 x 4.4 mm RTC External 32,768 Hz crystal required Included GPIO SPI 3 2 Ethernet ENC28J60 over SPI ENC28J60 over SPI and/or Built in base 100 Ethernet PHY Rev

5 GHI Electronics, LLC Introduction G120 and G120E SoM Datasheet 2.2 Key Features.NET Micro Framework USB client RoHS Lead Free SQLite database 120 MHz ARM Cortex-M3 NXP LPC Mbytes available RAM 2.3 Mbytes available flash Embedded LCD controller 72 to 80 GPIO 43 interrupt capable GPIO 2 to 3 SPI 1 I2C 5 UART 2 CAN 12 PWM 8 12-bit analog input 1 10-bit analog output 4-bit SD/MMC memory card interface Low power modes -40 C to +85 C operational RTC Watchdog Threading USB host TCP/IP with SSL o Full.NET socket interface o Ethernet o Wi-Fi o PPP Graphics o Images o Fonts o Controls File System o Full.NET file interface o SD cards o USB drives Native extensions o Runtime Loadable Procedures o Device register access Signal controls o Generation o Capture o Pulse measurement 2.3 Example Applications Vending machines POS Terminals Measurement tools and testers Networked sensors Robotics Central alarm system Smart appliances Industrial automation devices Rev

6 GHI Electronics, LLC The.NET Micro Framework G120 and G120E SoM Datasheet 3 The.NET Micro Framework Inspired by the full.net Framework, Microsoft developed a lightweight version called.net Micro Framework (NETMF). NETMF focuses on the specific requirements of resource-constrained embedded systems. Development, debugging, and deployment are all conveniently performed using Microsoft's powerful Visual Studio through a standard USB or serial cable. Programming is done in C# or Visual Basic with libraries that cover sockets, memory management with garbage collection, advanced file system support, multitasking services, and many others. In addition to supporting many standard.net features, NETMF has additional embedded extensions supporting microcontroller specific needs such as PWM outputs and analog inputs. 3.1 GHI Electronics and NETMF Since signing the partnership agreement with Microsoft in 2008, GHI Electronics has become the leading Microsoft partner on NETMF through its work on integrating and extending the NETMF core. GHI Electronics's NETMF products are extended with important features extending the NETMF libraries such as databases, USB Host, Wi-Fi, and native programming. Rev

7 GHI Electronics, LLC Pinout Tables G120 and G120E SoM Datasheet 4 Pinout Tables Many signals on the G120 are multiplexed to offer multiple functions on a single pin. Developers can decide on the pin functionality to be used through the provided libraries. Any pin with no name, function, or note must be left unconnected. 4.1 G120 Pinout Pin Name Function Pin Name Function Pin Name Function 1 GND 32 P4.29 COM4 RX 63 1 P0.27 I2C SDA V 33 P P3.25 PWM7 3 P2.4 PWM10 LCD OE 34 P P3.24 PWM6 4 P2.8 LCD R3 35 P USBC D+ 5 P0.0 CAN1 RD 36 P USBC D- 6 P0.10 COM3 TX 37 P USBH D- 7 P P USBH D+ 8 P2.10 LDR0 39 P1.4 SPI3 MISO 70 P P0.11 COM3 RX 40 P P1.22 LCD G2 10 P0.1 CAN1 TD 41 P1.1 SPI3 MOSI TOUCH XR 72 P1.21 LCD G1 11 P0.18 SPI1 MOSI 42 P1.0 SPI3 SCK TOUCH YD 73 P1.19 COM3 OE 12 P0.16 COM2 RX P1.23 LCD G3 13 P0.15 SPI1 SCK P1.24 LCD G4 14 P0.22 LDR1 45 GND 76 P1.20 LCD G0 15 P0.17 COM2 CTS SPI1 MISO V 77 P1.25 LCD G5 16 P2.1 MODE 47 P0.3 COM1 RX 78 P1.26 LCD B1 17 P0.6 COM2 RTS COM2 OE 48 P0.2 COM1 TX 79 P1.28 LCD B3 18 P2.0 COM2 TX 49 P0.26 ADC3 DAC0 80 P1.29 LCD B4 COM5 TX 19 SPI2 SCK 50 P0.24 ADC1 TOUCH YU 81 GND 20 SPI2 MISO 51 P0.25 ADC2 82 P1.27 LCD B2 21 SPI2 MOSI 52 P0.23 ADC0 TOUCH XL 83 P2.13 LCD B0 22 P1.12 SD D3 53 RESET 84 P2.12 LCD R0 23 P1.11 PWM5 SD D2 54 P3.26 PWM8 85 P2.5 LCD HS PWM11 24 P1.7 PWM4 SD D1 55 P0.13 ADC7 86 P2.2 LCD CLK 25 P1.2 PWM0 SD CLK 56 P0.12 ADC6 87 P2.7 LCD R2 26 P1.6 PWM3 SD D0 57 RTC CRYSTAL 1 88 P2.9 LCD R4 COM5 RX 27 GND 58 RTC CRYSTAL 2 89 P2.6 LCD R1 28 P1.3 PWM1 SD CMD 59 2 P1.30 ADC4 COM4 OE 90 P2.3 LCD VS PWM9 29 P0.5 CAN2 TD 60 VBAT 91 P1.5 PWM2 30 P0.4 CAN2 RD 61 1 P0.28 I2C SCL 31 P4.28 COM4 TX 62 P1.31 ADC5 1 Open drain requiring a 2.2 kω pull-up resistor 2 Must not be low on startup Rev

8 GHI Electronics, LLC Pinout Tables G120 and G120E SoM Datasheet 4.2 G120E Pinout Pin Name Function Pin Name Function Pin Name Function V 36 GND J1 P GND V J2 P2.1 MODE 3 P0.4 CAN2 RD 38 P3.30 J3 P2.23 TOUCH XR 4 P0.5 CAN2 TD 39 P3.26 PWM8 J4 P3.31 TOUCH YD 5 P0.3 COM1 RX 40 P3.17 PWM1 J5 P3.29 PWM11 6 P0.2 COM1 TX 41 USBC D- J6 P P0.22 LDR1 42 USBC D+ J7 8 P0.24 TOUCH YU ADC1 43 ETH PHY RD- J8 9 P0.25 COM4 TX ADC2 44 ETH PHY RD+ J9 P3.19 PWM3 10 P0.26 COM4 RX ADC3 DAC0 45 ETH PHY TD- J10 P3.20 PWM4 11 P0.23 TOUCH XL ADC0 46 ETH PHY TD+ J11 P3.21 PWM5 12 P P0.18 SPI1 MOSI J12 P3.28 PWM10 13 P P0.17 SPI1 MISO J13 ETH PHY SPEED 14 1 P0.28 I2C SCL 49 P2.30 J14 ETH PHY LINK 15 1 P0.27 I2C SDA 50 P0.15 SPI1 SCK J15 GND 16 P3.16 PWM0 51 P0.11 COM3 RX T1 P2.12 LCD R0 17 P3.24 PWM6 52 P0.10 COM3 TX T2 P2.6 LCD R1 18 P3.25 PWM7 53 P2.10 LDR0 T3 P2.7 LCD R2 19 P P0.6 COM2 RTS T4 P2.8 LCD R3 20 P P0.16 COM2 RX T5 P2.9 LCD R4 COM5 RX 21 P P2.31 T6 P1.20 LCD G0 22 P P3.18 COM2 CTS PWM2 T7 P1.21 LCD G1 23 P0.1 CAN1 TD 58 SPI2 SCK T8 P1.22 LCD G2 24 P SPI2 MOSI T9 P1.23 LCD G3 25 P0.0 CAN1 RD 60 P2.0 COM2 TX T10 P1.24 LCD G4 26 P1.30 ADC4 61 SPI2 MISO T11 P1.25 LCD G5 27 P P1.12 SD D3 T12 P2.13 LCD B0 28 VBAT 63 P1.11 SD D2 T13 P1.26 LCD B1 29 USBH D- 64 P1.7 SD D1 T14 P1.27 LCD B2 30 USBH D+ 65 P1.2 SD CLK T15 P1.28 LCD B3 31 P0.12 ADC6 66 P1.6 SD D0 T16 P1.29 LCD B4 COM5 TX 32 P0.13 ADC7 67 P1.3 SD CMD T17 P2.2 LCD CLK 33 P1.31 ADC5 68 SD PWR T18 P2.4 LCD OE V 69 GND T19 P2.5 LCD HS 35 P3.27 PWM9 70 RESET T20 P2.3 LCD VS 1 Open drain requiring a 2.2 kω pull-up resistor Rev

9 GHI Electronics, LLC Reference Design G120 and G120E SoM Datasheet 5 Reference Design The G120E Dev Board is an excellent starting point and reference design for anyone interested in evaluating and developing with the G120. See the product catalog entry for more information and additional resources. Rev

10 GHI Electronics, LLC Device Startup G120 and G120E SoM Datasheet 6 Device Startup The G120 is held in reset when the reset pin is low. Releasing it will begin the system startup process. It is pulled high internally on the G120E and left floating on the G120. There are four different components of the device firmware: 1. GHI Bootloader: initializes the system, updates TinyBooter when needed, and executes TinyBooter. 2. TinyBooter: executes TinyCLR, updates TinyCLR when needed, and updates the system configuration. 3. TinyCLR: loads, debugs, and executes the managed application. 4. Managed application: the program developed by the customer. Which components get executed on startup can be control by manipulating the LDR0 and LDR1 pins. LDR0 and LDR1 are pulled high on startup. LDR0 LDR1 Effect Ignored High Execute the managed application. High Low Wait in TinyBooter Low Low Wait in GHI Bootloader Additionally, the communications interface between the host PC and the G120 is selected on startup through the MODE pin, which is pulled high on startup. MODE G120 G120E High USB COM1 Low COM1 USB The above discussed functions of LDR0, LDR1, and MODE are only during startup. After startup, they return to the default GPIO state and are available to use as GPIO in the user application. Rev

11 GHI Electronics, LLC Libraries G120 and G120E SoM Datasheet 7 Libraries Similar to the full.net Framework, NETMF includes many built in libraries to help in modern application development with additional libraries to support embedded systems. Please see for more information. 7.1 General Purpose Input and Output (GPIO) GPIOs can read and write logical high and low signals. Keep the following in mind: They default to inputs with internal weak pull-up resistors They operate on 3.3 V logic levels. They are 5 V tolerant when not in analog mode. They have controllable pull up and pull down resistors. Only pins on ports 0 and 2 are interrupt capable. Individual pins can source or sink up to 4 ma (see the processor s documentation for advanced information). 7.2 Analog Input Analog inputs can read voltages from 0 V to 3.3 V with 12-bit resolution. The built in analog circuitry uses the source voltage as a reference which can cause some noise on the analog signal. High accuracy ADCs with a dedicated reference can be added externally. 7.3 Analog Output Analog outputs can vary their voltage from 0 V to 3.3 V with 10-bit resolution. The output voltage is meant to be used as a signal and not a driver. An op-amp or similar circuit can be used to amplify the current. 7.4 Pulse Width Modulation (PWM) PWM is used to create a waveform with a specified frequency and duty cycle. It uses built-in hardware so no processing resources are needed to keep it running. Frequencies can range from 1 Hz to 30 MHz. Some PWM channels share the same source clock internally. Changing the frequency on a channel will affect other channels; however, they can have a separate duty cycle. Channel Timer 0 to to Signal Generator Signal Generator is used to generate a waveform on any GPIO with varying frequency and duty cycle. The feature is software driven and can generate frequencies up to 40 khz ±10%. More processing time is required for higher frequencies. Rev

12 GHI Electronics, LLC Libraries G120 and G120E SoM Datasheet 7.6 Signal Capture Signal Capture monitors any GPIO and records the time from the last change. This feature is software driven and can measure frequencies up to 100 khz ±10%. Lower frequencies have higher accuracy. 7.7 Pulse Feedback Pulse Feedback is used for sensing capacitance on any GPIO input and measuring pulses from ultrasonic distance and other sensors. When used for sensing capacitance, a 100 pf capacitor and 1 resistor between the pad and ground are recommended. 7.8 Universal Asynchronous Receiver Transmitter (UART) UART is a common, full duplex, communications interface. Baud rates from 1,200 to 921,600 are supported. Handshaking is supported on COM2 only. Data bits between 5 and 8 are supported. Stop bits of 1 and 2 are supported, 2 stop bits are not supported with five data bits. Space, mark, even, and odd parities are supported. 7.9 Serial Peripheral Interface (SPI) SPI is a common three or four wire serial interface. The G120 can act as a SPI bus master only. The maximum supported clock is 30 MHz and all four SPI modes are supported. The SPI bus is designed to interface with multiple SPI slave devices. The active slave is selected by asserting the chip select line on the slave device. SPI2 is shared internally with the flash memory on the G120. Use of a chip select with devices on this channel is required or the G120 will not function properly. The use of another SPI channel is recommended Inter-Integrated Circuit (I2C) I2C is a two-wire addressable serial interface. The G120 can act as an I2C bus master only with 7-bit slave addresses. It can connect to one or more slave devices over the same connection with a maximum clock of 400 khz. The I2C bus interface requires pull up resistors to be added on both the SCL and SDA pins, usually 2.2 kω. It is possible to simulate an independent I2C bus on any two GPIO pins with the appropriate resistors though the software I2C class, but performance will be lower Controller Area Network (CAN) CAN is a common interface in industrial control and the automotive industry. CAN on the G120 is compliant with the CAN 2.0B specifications. Bitrates up to 1 Mbit/s are supported. For systems with higher traffic, different message filter options are available Wire Through 1-Wire, a master can communicate with multiple 1-Wire slaves using any GPIO Graphics The G120 supports 16-bit color TFT displays up to 800x600. Displays require the horizontal sync, vertical sync, clock, enable, and the 16 color lines. The color format is 565 (5 bits for red, 6 bits for green, and 5 bits for blue). If Rev

13 GHI Electronics, LLC Libraries G120 and G120E SoM Datasheet the display has more than 16 color lines, connect the most significant color lines to the G120 and the remaining lines to ground. While SPI displays can be utilized as well, the native TFT interface is recommended as it allows for a faster update rate. NETMF includes support for drawing though the bitmap object. TrueType font files can be used once converted to the TinyFont format used by NETMF Touch Screen The G120 supports displays with four-wire restive touch without the need for any additional hardware, though using an external controller is possible. The default touch pins can be remapped if required. Capacitive touch displays can be used through the I2C interface USB Host USB host allows the use of USB mass storage devices, joysticks, keyboards, and mice. Additionally, for USB devices that do not have a standard class included, low level USB access is provided for bulk transfers. USB hubs are supported allowing multiple devices to be connected USB Client The USB client interface is typically used as the G120 debug interface and for application deployment through Visual Studio. However, it is controllable and may be used to simulate other USB devices such as mice, keyboards, and Communications Device Class (CDC) interfaces using low level access instead of the debug interface File System The G120 supports accessing files on SD cards and USB memory devices formatted as FAT16 or FAT32. SD cards use a true 4-bit interface. MMC/SD/SDHC/SDXC cards in full, mini, and micro formats and any USB device with mass storage class are supported. Access speeds are dependent on many different factors and can be up to 500 Kbyte/s Networking The G120 supports Ethernet, Wi-Fi, and PPP. The full stack includes TCP, UDP, DHCP, DNS, HTTP, FTP, and others. Secure connections can be created using the built in SSL stack Ethernet Ethernet support is available using the built-in NETMF TCP/IP and SSL stack through the on-board base-100 Ethernet PHY on the G120E and through an external ENC28J60 SPI Ethernet chip on both the G120 and the G120E Wi-Fi Any Wi-Fi module with a built-in TCP/IP stack can be used with the G120. However, these modules are typically limited. Through the supported Redpine RS9110-N and RS9110-N chips, Wi-Fi is usable with the built-in NETMF TCP/IP and SSL stacks. Rev

14 GHI Electronics, LLC Libraries G120 and G120E SoM Datasheet Point to Point The Point to Point (PPP) protocol is often used for devices needing to connect to mobile networks. While typical embedded devices use the mobile modem's built-in and very limited TCP/IP stack, systems using the G120 can use these modems with the internal NETMF TCP/IP and SSL stack Extended Weak References Extended Weak References are a way for managed applications to store data in non-volatile memory. This is meant to be used as a configuration store that does not change frequently where the data can be recreated if needed. There are 128 KBytes available for use Configuration Access to the configuration sector of the device is provided for storage of small, infrequently changing, entries. The data will be lost if the configuration is reflashed. Space is limited and varies based on other information stored in the configuration Real Time Clock The real time clock (RTC) is used to keep time while the processor is off, drawing its power from a 3 V backup battery or super capacitor providing 3 V. An appropriate 32,768 Hz crystal and its associated circuitry must be connected to the G120 for the RTC to function. It is included on the G120E Watchdog Watchdog is used to reset the system if it enters an erroneous state. The G120 supports timeouts between 1 ms and 134,217 ms. Watchdog support is included through the GHI Electronics libraries replacing the built in NETMF version Power Control The G120 supports entering sleep, deep sleep, and off modes in order to reduce power usage. It can consume as little as 120 ma in sleep, 18 ma in deep sleep, and 12 ma in off. It may be woken from an RTC alarm or a GPIO interrupt. Sleep pauses execution of the program. Deep sleep pauses execution of the program and shuts down many internal functions. Off shuts down all internal functions and can only be woken by the RTC alarm or a system reset. The system will be automatically reset when exiting off mode In-Field Update Through In-Field Update, the G120 can update its firmware and managed application. The update can come from the network, a bus, or connected media SQLite Database SQLite can be used to created databases that can be stored in memory or on a supported storage device such as a USB drive or SD card. Rev

15 GHI Electronics, LLC Libraries G120 and G120E SoM Datasheet 7.26 Direct Memory Access Low level device registers and memory can be accessed to further configure the G120 s underlying processor. Not all functionality of the processor is available as some functions may be used or configured internally for use in NETMF Battery RAM Battery-backed RAM is provided as part of the internal RTC. This memory retains its contents when the power is lost as long as there is a backup battery. There are 20 bytes of battery backed RAM available. Consult the processor's documentation for details on use EEPROM The G120 has a built-in EEPROM. Consult the processor's documentation for details on use Runtime Loadable Procedure s Similar to code loaded from a DLL, Runtime Loadable Procedures (RLP) allows a binary or ELF image to be loaded into memory and executed on the device. This is useful for advanced and critical performance scenarios. The RLP region starts at address 0xA0F00000 and is 0x000FFFFC bytes in size. Your compiled images must fall completely within that range. Rev

16 GHI Electronics, LLC Design Considerations G120 and G120E SoM Datasheet 8 Design Considerations 8.1 Required Pins Exposing the following pins is required in every design to enable device programming, updates, and recovery: LDR0 LDR1 Desired debug interface(s) MODE if required to select a debug interface 8.2 Power Supply A typical clean power source, suited for digital circuitry, is needed to power the G120. Voltages should be within at least 10% of the needed voltage. Decoupling capacitors of 0.1 μf are needed near every power pin. Additionally, a large capacitor, typically 47 μf, should be near the G120 if the power supply is more than few inches away. 8.3 Crystals The G120 and G120E include the needed system crystal and its associated circuitry. The G120E additionally includes the RTC crystal and its associated circuitry. However, the G120 does not. It requires an external 32,768 Hz crystal and circuitry for the RTC to function. Please see the processor s documentation for advanced information. 8.4 Interrupt Pins Only pins on ports 0 and 2 support interrupts. 8.5 Reset The G120E includes an internal pull-up resistor on the reset pin. The G120 does not, so an external 15 kω pull-up resistor is required for correct operation. 8.6 SPI Channels SPI2 is shared internally with the flash memory on the G120. Use of a chip select with devices on this channel is required or the G120 will not function properly. The use of another SPI channel is recommended. 8.7 Ethernet The built in Ethernet available on the G120E includes all needed Ethernet circuitry internally. However, an appropriate magnet and connector, like the J0011D or similar, are required. 8.8 Direct Memory Access Most of the core processor s resources are used by NETMF. Some resources are permanently used, like the main system timer while others are used when specific features, like the timers for PWM, are enabled. Used resources can change from one firmware version to another so care must be taken when using these resources through RLP or other direct memory access methods. Rev

17 GHI Electronics, LLC Design Considerations G120 and G120E SoM Datasheet When absolutely required, applications can use resources in conjunction with NETMF. For example, creating a special baud rate, utilizing the timer capture feature, and making use of many other features supported by the processor. Please contact GHI Electronics s consulting services to determine exactly what resources are available and if the G120 can fulfill the specific requirements. Rev

18 GHI Electronics, LLC Footprints G120 and G120E SoM Datasheet 9 Footprints We recommend no traces or vias under the module. Dimensions are in inches. 9.1 G120 Recommended Footprint Rev

19 GHI Electronics, LLC Footprints G120 and G120E SoM Datasheet 9.2 G120E Recommended Footprint Rev

20 GHI Electronics, LLC Soldering the G120 G120 and G120E SoM Datasheet 10 Soldering the G120 The G120 is designed to be easily machine-placed or hand-soldered. Static sensitive precautions should be taken when handling the module Oven Reflow The G120 is not sealed for moisture. Baking the module before reflow is recommended and required in a humid environment. The process of reflow can damage the G120 if the temperature is too high or exposure is too long. The lead-free reflow profile used by GHI Electronics is shown below. The profiles shown are based on SAC 305 solder (3% silver, 0.5% copper). The thermal mass of the assembled board and the sensitivity of the components on it affect the total dwell time. Differences in the two profiles are where they reach their respective peak temperatures as well as the time above liquids (TAL). The shorter profile applies to smaller assemblies, whereas the longer profile applies to larger assemblies such as back-planes or high-density boards. The process window is described by the shaded area. These profiles are only starting-points and general guidance. The particulars of an oven and the assembly will determine the final process. Rev

21 GHI Electronics, LLC Legal Notice G120 and G120E SoM Datasheet 11 Legal Notice 11.1 Licensing The G120 SoM and G120E SoM, with all their built-in software components, are licensed for commercial and noncommercial use. No additional fee or licensing is required. Software, firmware, and libraries provided for the G120 SoM and the G120E SoM are licensed to be used on the G120 SoM and the G120E SoM only Trademarks G120 and G120E are trademarks of GHI Electronics, LLC..NET Micro Framework and Visual Studio are registered or unregistered trademarks of Microsoft Corporation. Other registered or unregistered trademarks are owned by their respective companies Disclaimer IN NO EVENT SHALL GHI ELECTRONICS, LLC BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS PRODUCT, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. GHI ELECTRONICS, LLC LINE OF PRODUCTS ARE NOT DESIGNED FOR LIFE SUPPORT APPLICATIONS. SPECIFICATIONS AND AVAILABILITY ARE SUBJECT TO CHANGE WITHOUT ANY NOTICE. Rev

22 GHI Electronics, LLC Revision History G120 and G120E SoM Datasheet 12 Revision History Revision Date Change Fixed MODE default state Initial release. Rev

G80 SoC Datasheet. Where Hardware Meets Software

G80 SoC Datasheet. Where Hardware Meets Software GHI Electronics, LLC 501 E. Whitcomb Ave. Madison Heights, Michigan 48071 Phone: (248) 397-8856 Fax: (248) 397-8890 www.ghielectronics.com G80 SoC Datasheet Where Hardware Meets Software GHI Electronics,

More information

G400S and G400D SoM Datasheet

G400S and G400D SoM Datasheet GHI Electronics, LLC 501 E. Whitcomb Ave. Madison Heights, Michigan 48071 Phone: (248) 397-8856 Fax: (248) 397-8890 www.ghielectronics.com G400S and G400D SoM Datasheet G400S SoM G400D SoM Where Hardware

More information

Preliminary F40 SoC Datasheet

Preliminary F40 SoC Datasheet GHI Electronics, LLC 501 E. Whitcomb Ave. Madison Heights, Michigan 48071 Phone: (248) 397-8856 Fax: (248) 397-8890 www.ghielectronics.com Preliminary F40 SoC Datasheet Where Hardware Meets Software GHI

More information

G120 Module Specifications

G120 Module Specifications G120 Module is a surface-mount System on Module (SoM) that runs.net Micro Framework software platform; a tiny version of Microsoft.NET framework. The value of G120 Module is not only in the hardware capabilities

More information

EMX Module Specifications

EMX Module Specifications EMX is a combination of hardware (ARM Processor, Flash, RAM, Ethernet PHY...etc) on a very small (1.55 x1.8 ) SMT OEM 8-Layer board that hosts Microsoft.NET Micro Framework with various PAL/HAL drivers.

More information

Preliminary File System User Manual

Preliminary File System User Manual GHI Electronics, LLC 501 E. Whitcomb Ave. Madison Heights, Michigan 48071 Phone: (248) 397-8856 Fax: (248) 397-8890 www.ghielectronics.com Preliminary File System User Manual Where Hardware Meets Software

More information

Prototyping Module Datasheet

Prototyping Module Datasheet Prototyping Module Datasheet Part Numbers: MPROTO100 rev 002 Zenseio LLC Updated: September 2016 Table of Contents Table of Contents Functional description PROTOTYPING MODULE OVERVIEW FEATURES BLOCK DIAGRAM

More information

EMX Development System

EMX Development System July 21, 2010 G H I Getting Started E l e c t r o n i c s Table of Contents Table of Contents 1.Introduction...3 The objective of this Guide...4 2.Getting Started...5 2.1.System Setup...5 2.2.The Emulator...6

More information

Product Specification

Product Specification Product Specification Features Amp ed RF, Inc. Description 15mm x 27mm The added class 1 power, +18dBm, of the BT-11, gives this module one of the best ranges in the industry. It s completely pin compatible

More information

Rev. 4.4 March 10, 2011 User Manual. This document covers information about USBizi Chipset, specifications, tutorials and references.

Rev. 4.4 March 10, 2011 User Manual. This document covers information about USBizi Chipset, specifications, tutorials and references. Rev. 4.4 March 10, 2011 User Manual USBizi Chipset LQFP144 USBizi Chipset LQFP100 Document Information Information Abstract Description This document covers information about USBizi Chipset, specifications,

More information

BV511 Hardware Guide ByVac ByVac Revision 1.0

BV511 Hardware Guide ByVac ByVac Revision 1.0 BV511 Hardware Guide ByVac ByVac 2007 www.byvac.co.uk Revision 1.0 ByVac 1 Copyright in this work is vested in ByVac and the document is issued in confidence for the purpose only for which it is supplied.

More information

Product Specification

Product Specification Product Specification 15mm x 27mm Description One of the most capable Bluetooth modules available, the BT-21 Bluetooth OEM Module is designed for maximum flexibility. The BT-21 module includes 14 general

More information

eip-24/100 Embedded TCP/IP 10/100-BaseT Network Module Features Description Applications

eip-24/100 Embedded TCP/IP 10/100-BaseT Network Module Features Description Applications Embedded TCP/IP 10/100-BaseT Network Module Features 16-bit Microcontroller with Enhanced Flash program memory and static RAM data memory On board 10/100Mbps Ethernet controller, and RJ45 jack for network

More information

Universität Dortmund. IO and Peripheral Interfaces

Universität Dortmund. IO and Peripheral Interfaces IO and Peripheral Interfaces Microcontroller System Architecture Each MCU (micro-controller unit) is characterized by: Microprocessor 8,16,32 bit architecture Usually simple in-order microarchitecture,

More information

Design and development of embedded systems for the Internet of Things (IoT) Fabio Angeletti Fabrizio Gattuso

Design and development of embedded systems for the Internet of Things (IoT) Fabio Angeletti Fabrizio Gattuso Design and development of embedded systems for the Internet of Things (IoT) Fabio Angeletti Fabrizio Gattuso Microcontroller It is essentially a small computer on a chip Like any computer, it has memory,

More information

BT-22 Product Specification

BT-22 Product Specification BT-22 Product Specification Features Amp ed RF, Inc. Description 10.4 mm x 13.5 mm Our micro-sized Bluetooth module is the smallest form factor available providing a complete RF platform. The BT-22 is

More information

Arduino Uno. Arduino Uno R3 Front. Arduino Uno R2 Front

Arduino Uno. Arduino Uno R3 Front. Arduino Uno R2 Front Arduino Uno Arduino Uno R3 Front Arduino Uno R2 Front Arduino Uno SMD Arduino Uno R3 Back Arduino Uno Front Arduino Uno Back Overview The Arduino Uno is a microcontroller board based on the ATmega328 (datasheet).

More information

AT-501 Cortex-A5 System On Module Product Brief

AT-501 Cortex-A5 System On Module Product Brief AT-501 Cortex-A5 System On Module Product Brief 1. Scope The following document provides a brief description of the AT-501 System on Module (SOM) its features and ordering options. For more details please

More information

DATASHEET. MK-070C-HP High Performance 7 Inch Capacitive Touch Display. Amulet. Technologies. July 2015 Revision A

DATASHEET. MK-070C-HP High Performance 7 Inch Capacitive Touch Display. Amulet. Technologies. July 2015 Revision A High Performance 7 Inch Capacitive Touch Display DATASHEET July 2015 Revision A Introduction The MK-070C is the newest family member in the Display Module product line. The new 7 Capacitive Display Module

More information

HZX N03 Bluetooth 4.0 Low Energy Module Datasheet

HZX N03 Bluetooth 4.0 Low Energy Module Datasheet HZX-51822-16N03 Bluetooth 4.0 Low Energy Module Datasheet SHEN ZHEN HUAZHIXIN TECHNOLOGY LTD 2017.7 NAME : Bluetooth 4.0 Low Energy Module MODEL NO. : HZX-51822-16N03 VERSION : V1.0 1.Revision History

More information

March 21, BT22 Datasheet. Amp ed RF Technology, Co., Ltd.

March 21, BT22 Datasheet. Amp ed RF Technology, Co., Ltd. March 21, 2011 BT22 Datasheet Amp ed RF Technology, Co., Ltd. BT22 Features Bluetooth features Bluetooth qualified Bluetooth v2.1+edr Class 2 radio Range up to 30m LOS Description 10.4 mm x 13.5 mm Our

More information

BT 31 Data Sheet. Amp ed RF Technology Inc.

BT 31 Data Sheet. Amp ed RF Technology Inc. BT 31 Data Sheet Amp ed RF Technology Inc. Product Specification BT31 Features Bluetooth features FCC&Bluetooth licensed radio Bluetooth v3.0 Class 1 radio Range up to 100m LOS 1.5Mbps data throughput

More information

ARDUINO MEGA 2560 REV3 Code: A000067

ARDUINO MEGA 2560 REV3 Code: A000067 ARDUINO MEGA 2560 REV3 Code: A000067 The MEGA 2560 is designed for more complex projects. With 54 digital I/O pins, 16 analog inputs and a larger space for your sketch it is the recommended board for 3D

More information

KBC1122/KBC1122P. Mobile KBC with Super I/O, SFI, ADC and DAC with SMSC SentinelAlert! TM PRODUCT FEATURES. Data Brief

KBC1122/KBC1122P. Mobile KBC with Super I/O, SFI, ADC and DAC with SMSC SentinelAlert! TM PRODUCT FEATURES. Data Brief KBC1122/KBC1122P Mobile KBC with Super I/O, SFI, ADC and DAC with SMSC SentinelAlert! TM PRODUCT FEATURES Data Brief 3.3V Operation with 5V Tolerant Buffers ACPI 1.0b/2.0 and PC99a/PC2001 Compliant LPC

More information

Arduino Uno R3 INTRODUCTION

Arduino Uno R3 INTRODUCTION Arduino Uno R3 INTRODUCTION Arduino is used for building different types of electronic circuits easily using of both a physical programmable circuit board usually microcontroller and piece of code running

More information

ARDUINO YÚN MINI Code: A000108

ARDUINO YÚN MINI Code: A000108 ARDUINO YÚN MINI Code: A000108 The Arduino Yún Mini is a compact version of the Arduino YUN OVERVIEW: Arduino Yún Mini is a breadboard PCB developed with ATmega 32u4 MCU and QCA MIPS 24K SoC CPU operating

More information

SBAT90USB162 Atmel. SBAT90USB162 Development Board User s Manual

SBAT90USB162 Atmel. SBAT90USB162 Development Board User s Manual SBAT90USB162 Atmel AT90USB162 Development Board User s manual 1 1. INTRODUCTION Thank you for choosing the SBAT90USB162 Atmel AT90USB162 development board. This board is designed to give a quick and cost-effective

More information

Part Number: PCB-STM32-F4B1 (unpopulated PCB with Discovery module sockets, no other parts) STM32-F4B1 (assembled board, not presently available)

Part Number: PCB-STM32-F4B1 (unpopulated PCB with Discovery module sockets, no other parts) STM32-F4B1 (assembled board, not presently available) PCB-STM32-F4B1 Development baseboard for the STMicro Discovery-F4 module (STMicro part# STM32F4DISCOVERY) PCB Rev 1.00 shown. PCB Rev 1.20 has on-board RS232 drivers. Part Number: PCB-STM32-F4B1 (unpopulated

More information

ZigBee Compliant Platform 2.4G RF Low Power Transceiver Module for IEEE Standard. DATA SHEET Version B

ZigBee Compliant Platform 2.4G RF Low Power Transceiver Module for IEEE Standard. DATA SHEET Version B ZMD400-A01 ZigBee Compliant Platform 2.4G RF Low Power Transceiver Module for IEEE 802.15.4 Standard DATA SHEET Version B Quan International Co., Ltd., ZMD400 Features Fully compliant 802.15.4 Standard

More information

ARDUINO MEGA ADK REV3 Code: A000069

ARDUINO MEGA ADK REV3 Code: A000069 ARDUINO MEGA ADK REV3 Code: A000069 OVERVIEW The Arduino MEGA ADK is a microcontroller board based on the ATmega2560. It has a USB host interface to connect with Android based phones, based on the MAX3421e

More information

USER GUIDE EDBG. Description

USER GUIDE EDBG. Description USER GUIDE EDBG Description The Atmel Embedded Debugger (EDBG) is an onboard debugger for integration into development kits with Atmel MCUs. In addition to programming and debugging support through Atmel

More information

ARDUINO UNO REV3 SMD Code: A The board everybody gets started with, based on the ATmega328 (SMD).

ARDUINO UNO REV3 SMD Code: A The board everybody gets started with, based on the ATmega328 (SMD). ARDUINO UNO REV3 SMD Code: A000073 The board everybody gets started with, based on the ATmega328 (SMD). The Arduino Uno SMD R3 is a microcontroller board based on the ATmega328. It has 14 digital input/output

More information

Microcontroller. BV523 32bit Microcontroller. Product specification. Jun 2011 V0.a. ByVac Page 1 of 8

Microcontroller. BV523 32bit Microcontroller. Product specification. Jun 2011 V0.a. ByVac Page 1 of 8 32bit Product specification Jun 2011 V0.a ByVac Page 1 of 8 Contents 1. Introduction...3 2. Features...3 3. Physical Specification...3 3.1. PIC32...3 3.2. USB Interface...3 3.3. Power Supply...4 3.4. Power

More information

NXP AN11528 sensor Application note

NXP AN11528 sensor Application note NXP sensor Application note http://www.manuallib.com/nxp/an11528-sensor-application-note.html This application note will illustrate the new features of the LPC11U6x device family compared to the LPC11U3x

More information

DEVBOARD3 DATASHEET. 10Mbits Ethernet & SD card Development Board PIC18F67J60 MICROCHIP

DEVBOARD3 DATASHEET. 10Mbits Ethernet & SD card Development Board PIC18F67J60 MICROCHIP DEVBOARD3 DATASHEET 10Mbits Ethernet & SD card PIC18F67J60 MICROCHIP Version 1.0 - March 2009 DEVBOARD3 Version 1.0 March 2009 Page 1 of 7 The DEVBOARD3 is a proto-typing board used to quickly and easily

More information

EDBG. Description. Programmers and Debuggers USER GUIDE

EDBG. Description. Programmers and Debuggers USER GUIDE Programmers and Debuggers EDBG USER GUIDE Description The Atmel Embedded Debugger (EDBG) is an onboard debugger for integration into development kits with Atmel MCUs. In addition to programming and debugging

More information

ARDUINO UNO REV3 Code: A000066

ARDUINO UNO REV3 Code: A000066 ARDUINO UNO REV3 Code: A000066 The UNO is the best board to get started with electronics and coding. If this is your first experience tinkering with the platform, the UNO is the most robust board you can

More information

ESPino - Specifications

ESPino - Specifications ESPino - Specifications Summary Microcontroller ESP8266 (32-bit RISC) WiFi 802.11 (station, access point, P2P) Operating Voltage 3.3V Input Voltage 4.4-15V Digital I/O Pins 9 Analog Input Pins 1 (10-bit

More information

Pridgen Vermeer Robotics Xmega128 Manual

Pridgen Vermeer Robotics Xmega128 Manual Features: 12x PWM signals with 5V supply 8x A/D Inputs with 3.3V supply 2x RS 232 Terminals 1x SPI Interface 4x 8-bit Digital IO ports 3.3V Power Bus LCD Header (4-bit mode) Smart Power Connecter Power

More information

Arduino ADK Rev.3 Board A000069

Arduino ADK Rev.3 Board A000069 Arduino ADK Rev.3 Board A000069 Overview The Arduino ADK is a microcontroller board based on the ATmega2560 (datasheet). It has a USB host interface to connect with Android based phones, based on the MAX3421e

More information

APPLICATION NOTE. Atmel AT01080: XMEGA E Schematic Checklist. Atmel AVR XMEGA E. Features. Introduction

APPLICATION NOTE. Atmel AT01080: XMEGA E Schematic Checklist. Atmel AVR XMEGA E. Features. Introduction APPLICATION NOTE Atmel AT01080: XMEGA E Schematic Checklist Atmel AVR XMEGA E Features Power supplies Reset circuit Clocks and crystal oscillators PDI TWI Introduction This application note describes a

More information

DATASHEET. 4.3 Embedded SPI Display. 4DLCD-FT843 Powered by the FTDI FT800 Video Engine. Document Date: 25 th September 2013 Document Revision: 0.

DATASHEET. 4.3 Embedded SPI Display. 4DLCD-FT843 Powered by the FTDI FT800 Video Engine. Document Date: 25 th September 2013 Document Revision: 0. DATASHEET 4.3 Embedded SPI Display 4DLCD-FT843 Powered by the FTDI FT800 Video Engine Document Date: 25 th September 2013 Document Revision: 0.4 Uncontrolled Copy when printed or downloaded. Please refer

More information

MicroBolt. Microcomputer/Controller Featuring the Philips LPC2106 FEATURES

MicroBolt. Microcomputer/Controller Featuring the Philips LPC2106 FEATURES Microcomputer/Controller Featuring the Philips LPC2106 FEATURES Powerful 60 MHz, 32-bit ARM processing core. Pin compatible with 24 pin Stamp-like controllers. Small size complete computer/controller with

More information

I/O1 Xplained Pro. Preface. Atmel MCUs USER GUIDE

I/O1 Xplained Pro. Preface. Atmel MCUs USER GUIDE Atmel MCUs I/O1 Xplained Pro USER GUIDE Preface Atmel I/O1 Xplained Pro is an extension board to the Atmel Xplained Pro evaluation platform. I/O1 Xplained Pro is designed to give a wide variety of functionality

More information

specification: imp001

specification: imp001 specification: imp001 version 20140812 http://www.electricimp.com 1. Product description 1.1 General description The imp001 is a complete wireless network node in a card form factor. It works in conjunction

More information

USB2507. Integrated USB 2.0 Compatible 7-Port Hub PRODUCT FEATURES. Data Brief

USB2507. Integrated USB 2.0 Compatible 7-Port Hub PRODUCT FEATURES. Data Brief USB2507 Integrated USB 2.0 Compatible 7-Port Hub PRODUCT FEATURES Data Brief Integrated USB 2.0 Compatible 7-Port Hub 7 Transaction Translators for highest performance High-Speed (480Mbits/s), Full-Speed

More information

AN10955 Full-duplex software UART for LPC111x and LPC13xx

AN10955 Full-duplex software UART for LPC111x and LPC13xx Rev. 1 13 July 2010 Application note Document information Info Content Keywords LPC111X, LPC13XX, UART, software Abstract This application note illustrates how software running on an LPC111X or LPC13XX

More information

Preliminary. PACKAGE - 28-pin MLP (5mm X 5mm) Example Circuit Diagram CP V. 48MHz Oscillator. USB Function Controller 512B EEPROM

Preliminary. PACKAGE - 28-pin MLP (5mm X 5mm) Example Circuit Diagram CP V. 48MHz Oscillator. USB Function Controller 512B EEPROM Preliminary Single-Chip USB to UART Bridge SINGLE-CHIP USB to UART DATA TRANSFER - Integrated USB Transceiver; No External Resistors Required - Integrated Clock; No External Crystal Required - Integrated

More information

LPC-P1227 development board USER S MANUAL Initial release, March 2012 Designed by OLIMEX Ltd, 2011

LPC-P1227 development board USER S MANUAL Initial release, March 2012 Designed by OLIMEX Ltd, 2011 LPC-P1227 development board USER S MANUAL Initial release, March 2012 Designed by OLIMEX Ltd, 2011 All boards produced by Olimex LTD are ROHS compliant Disclaimer: 2012 Olimex Ltd. Olimex, logo and combinations

More information

keyestudio Keyestudio MEGA 2560 R3 Board

keyestudio Keyestudio MEGA 2560 R3 Board Keyestudio MEGA 2560 R3 Board Introduction: Keyestudio Mega 2560 R3 is a microcontroller board based on the ATMEGA2560-16AU, fully compatible with ARDUINO MEGA 2560 REV3. It has 54 digital input/output

More information

or between microcontrollers)

or between microcontrollers) : Communication Interfaces in Embedded Systems (e.g., to interface with sensors and actuators or between microcontrollers) Spring 2016 : Communication Interfaces in Embedded Systems Spring (e.g., 2016

More information

ARDUINO LEONARDO ETH Code: A000022

ARDUINO LEONARDO ETH Code: A000022 ARDUINO LEONARDO ETH Code: A000022 All the fun of a Leonardo, plus an Ethernet port to extend your project to the IoT world. You can control sensors and actuators via the internet as a client or server.

More information

eip-10 Embedded TCP/IP 10-BaseT Network Module Features Description Applications

eip-10 Embedded TCP/IP 10-BaseT Network Module Features Description Applications Embedded TCP/IP 10-BaseT Network Module Features 8-bit reprogrammable Microcontroller with Enhanced Flash program memory, EEPROM and Static RAM data memory On board 10Mbps Ethernet controller, and RJ45

More information

ARDUINO PRIMO. Code: A000135

ARDUINO PRIMO. Code: A000135 ARDUINO PRIMO Code: A000135 Primo combines the processing power from the Nordic nrf52 processor, an Espressif ESP8266 for WiFi, as well as several onboard sensors and a battery charger. The nrf52 includes

More information

USB2640i/USB2641i. Industrial Temperature USB 2.0 Flash Media Controller and Hub Combo PRODUCT FEATURES PRODUCT PREVIEW. General Description.

USB2640i/USB2641i. Industrial Temperature USB 2.0 Flash Media Controller and Hub Combo PRODUCT FEATURES PRODUCT PREVIEW. General Description. USB2640i/USB2641i Industrial Temperature USB 2.0 Flash Media Controller and Hub Combo PRODUCT FEATURES General Description The SMSC USB2640i/USB2641i is a USB 2.0 compliant, Hi-Speed hub for USB port expansion

More information

February 28,

February 28, February 28, 2014 1 http://www.mattairtech.com/ Table of Contents Overview...3 Introduction...3 Features...4 Hardware...5 Main Header Pins...5 ISP Header Pins...6 Solder Jumpers...6 Onboard 3.3V, 250mA

More information

Mega128-DEVelopment Board Progressive Resources LLC 4105 Vincennes Road Indianapolis, IN (317) (317) FAX

Mega128-DEVelopment Board Progressive Resources LLC 4105 Vincennes Road Indianapolis, IN (317) (317) FAX Mega128-DEVelopment Board Progressive Resources LLC 4105 Vincennes Road Indianapolis, IN 46268 (317) 471-1577 (317) 471-1580 FAX http://www.prllc.com GENERAL The Mega128-Development board is designed for

More information

Web Site: Forums: forums.parallax.com Sales: Technical:

Web Site:  Forums: forums.parallax.com Sales: Technical: Web Site: www.parallax.com Forums: forums.parallax.com Sales: sales@parallax.com Technical: support@parallax.com Office: (916) 624-8333 Fax: (916) 624-8003 Sales: (888) 512-1024 Tech Support: (888) 997-8267

More information

RN-174. WiFly GSX Super Module. Features. Description. Applications. rn-174-ds v1.1 1/24/2011

RN-174. WiFly GSX Super Module. Features. Description. Applications.   rn-174-ds v1.1 1/24/2011 www.rovingnetworks.com rn-174-ds v1.1 1/24/2011 WiFly GSX Super Module Features Development board containing the RN-171 module, status LEDs, power regulator Supports chip antenna (-C), PCB Trace antenna

More information

AARDVARK. Level Shifter Board. Level Shifter Board. Datasheet v1.00 February 15, 2008 I 2 C/SPI. Features

AARDVARK. Level Shifter Board. Level Shifter Board. Datasheet v1.00 February 15, 2008 I 2 C/SPI. Features Level Shifter Board AARDVARK I 2 C/SPI Features Level shifting of I 2 C, SPI, and MDIO signals from 1.2 V to 3.3 V I 2 C speeds of up to 800 khz SPI and MDIO speeds of up to 20 MHz Powering downstream

More information

ChipworkX Development System

ChipworkX Development System July 21, 2010 G H I Getting Started E l e c t r o n i c s Table of Contents Table of Contents 1.Introduction...3 The objective of this guide...4 2.Getting Started...5 2.1.System Setup...5 2.2.The Emulator...6

More information

SKB360I Bluetooth 4.0 Low Energy Module Datasheet

SKB360I Bluetooth 4.0 Low Energy Module Datasheet SKB360I Bluetooth 4.0 Low Energy Module Datasheet Name: Bluetooth 4.0 Low Energy Module Model No.: SKB360I Version: V1.01 Revision History: Revision Description Approved Date V1.01 Initial Release Hogan

More information

Dual Serial Shield User Manual

Dual Serial Shield User Manual Dual Serial Shield User Manual PN: 2050 Berkshire Products, Inc. Phone: 770-271-0088 http://www.bkp-store.com/ Rev: 1.00 Copyright 2013 Table of Contents 1 Introduction... 2 1.1 XB compatibility... 2 2

More information

AKKON USB CONTROLLER BOARD

AKKON USB CONTROLLER BOARD TN002 AKKON USB CONTROLLER BOARD USB Microcontroller board with the PIC18F4550 * Datasheet Authors: Gerhard Burger Version: 1.0 Last update: 20.01.2006 File: Attachments: no attachments Table of versions

More information

UM LPC General Purpose Shield (OM13082) Rev November Document information. Keywords

UM LPC General Purpose Shield (OM13082) Rev November Document information. Keywords Rev. 1.0 17 November 2015 User manual Document information Info Content Keywords LPCXpresso, LPC General Purpose Shield, OM13082 Abstract LPC General Purpose Shield User Manual Revision history Rev Date

More information

P4S-341 User Manual > Introduction. Overview

P4S-341 User Manual > Introduction. Overview P4S-341 User Manual > Introduction Overview P4S-341 is an industrial programmable I/O board. You can build various network communication systems connecting P4S-341 to many devices such as sensors and actuators.

More information

QT2 Xplained Pro. Preface. Atmel QTouch USER GUIDE

QT2 Xplained Pro. Preface. Atmel QTouch USER GUIDE Atmel QTouch QT2 Xplained Pro USER GUIDE Preface Atmel QT2 Xplained Pro kit is an extension board that enables the evaluation of a mutual capacitance touch surface using the Peripheral Touch Controller

More information

USB-to-I2C. Professional Hardware User s Manual.

USB-to-I2C. Professional Hardware User s Manual. USB-to-I2C Professional Hardware User s Manual https://www.i2ctools.com/ Information provided in this document is solely for use with the USB-to-I2C Professional product from SB Solutions, Inc. SB Solutions,

More information

QT3 Xplained Pro. Preface. Atmel QTouch USER GUIDE

QT3 Xplained Pro. Preface. Atmel QTouch USER GUIDE Atmel QTouch QT3 Xplained Pro USER GUIDE Preface The Atmel QT3 Xplained Pro is an extension board, which enables the evaluation of a capacitive touch 12 key numpad in mutual capacitance configuration.

More information

Pmod modules are powered by the host via the interface s power and ground pins.

Pmod modules are powered by the host via the interface s power and ground pins. 1300 Henley Court Pullman, WA 99163 509.334.6306 www.store. digilent.com Digilent Pmod Interface Specification 1.2.0 Revised October 5, 2017 1 Introduction The Digilent Pmod interface is used to connect

More information

Figure 1. Proper Method of Holding the ToolStick. Figure 2. Improper Method of Holding the ToolStick

Figure 1. Proper Method of Holding the ToolStick. Figure 2. Improper Method of Holding the ToolStick TOOLSTICK C8051F330 DAUGHTER CARD USER S GUIDE 1. Handling Recommendations To enable development, the ToolStick Base Adapter and daughter cards are distributed without any protective plastics. To prevent

More information

Hello, and welcome to this presentation of the STM32L4 power controller. The STM32L4 s power management functions and all power modes will also be

Hello, and welcome to this presentation of the STM32L4 power controller. The STM32L4 s power management functions and all power modes will also be Hello, and welcome to this presentation of the STM32L4 power controller. The STM32L4 s power management functions and all power modes will also be covered in this presentation. 1 Please note that this

More information

USB Port USB 2.0 Hub Controller PRODUCT FEATURES. Data Brief

USB Port USB 2.0 Hub Controller PRODUCT FEATURES. Data Brief USB2502 2-Port USB 2.0 Hub Controller PRODUCT FEATURES Data Brief Integrated USB 2.0 Compatible 2-Port Hub High-Speed (480Mbits/s), Full-Speed (12Mbits/s) and Low-Speed (1.5Mbits/s) compatible Full power

More information

Breeze Board. Type A. User Manual.

Breeze Board. Type A. User Manual. Breeze Board Type A User Manual www.dizzy.co.za Contents Introduction... 3 Overview Top... 4 Overview Bottom... 5 Getting Started (Amicus Compiler)... 6 Power Circuitry... 7 USB... 8 Microcontroller...

More information

EVE2 BLE Datasheet. The EVE Platform features standardized IO, common OS and drivers and ultra-low power consumption.

EVE2 BLE Datasheet. The EVE Platform features standardized IO, common OS and drivers and ultra-low power consumption. Datasheet Main features Software Micro-kernel with scheduling, power and clock management Contiki OS Tickless design Drivers for peripherals Bluetooth 4.1 compliant low energy singlemode protocol stack

More information

LPC-P1227 development board USER S MANUAL Revision B, July 2013 Designed by OLIMEX Ltd, 2011

LPC-P1227 development board USER S MANUAL Revision B, July 2013 Designed by OLIMEX Ltd, 2011 LPC-P1227 development board USER S MANUAL Revision B, July 2013 Designed by OLIMEX Ltd, 2011 All boards produced by Olimex LTD are ROHS compliant Disclaimer: 2013 Olimex Ltd. Olimex, logo and combinations

More information

Digital Circuits Part 2 - Communication

Digital Circuits Part 2 - Communication Introductory Medical Device Prototyping Digital Circuits Part 2 - Communication, http://saliterman.umn.edu/ Department of Biomedical Engineering, University of Minnesota Topics Microcontrollers Memory

More information

EX-9686U/A-L(A9) Hardware User Manual

EX-9686U/A-L(A9) Hardware User Manual EX-9686U/A-L(A9) Hardware User Manual Release Notes Version Release Date Notes 1.00 November, 2013 Initial Release 2.00 January, 2014 The 2 nd release Disclaimer This documentation is provided for use

More information

AK-STM32-ETH Development Board

AK-STM32-ETH Development Board AK-STM32-ETH Development Board Reference manual Copyright 2011 Artekit Italy All rights reserved Contents About this document... 3 Revision history... 3 Contact information... 3 Life support policy...

More information

USER GUIDE. Atmel OLED1 Xplained Pro. Preface

USER GUIDE. Atmel OLED1 Xplained Pro. Preface USER GUIDE Atmel OLED1 Xplained Pro Preface Atmel OLED1 Xplained Pro is an extension board to the Atmel Xplained Pro evaluation platform. The board enables the user to experiment with user interface applications

More information

USB3319. Hi-Speed USB Transceiver with 1.8V ULPI Interface - 13MHz Reference Clock PRODUCT FEATURES. Applications. Data Brief

USB3319. Hi-Speed USB Transceiver with 1.8V ULPI Interface - 13MHz Reference Clock PRODUCT FEATURES. Applications. Data Brief USB3319 Hi-Speed USB Transceiver with 1.8V ULPI Interface - 13MHz Reference Clock PRODUCT FEATURES Data Brief USB-IF Hi-Speed compliant to the Universal Serial Bus Specification Rev 2.0 Interface compliant

More information

Mercury System SB310

Mercury System SB310 Mercury System SB310 Ultrasonic Board - Product Datasheet Author Francesco Ficili Date 20/05/2018 Status Released Pag. 1 Revision History Version Date Author Changes 1.0 20/05/2018 Francesco Ficili Initial

More information

Color 7 click. PID: MIKROE 3062 Weight: 19 g

Color 7 click. PID: MIKROE 3062 Weight: 19 g Color 7 click PID: MIKROE 3062 Weight: 19 g Color 7 click is a very accurate color sensing Click board which features the TCS3472 color light to digital converter with IR filter, from ams. It contains

More information

RDB1768 Development Board User Manual

RDB1768 Development Board User Manual RDB1768 Development Board User Manual 6/16/2009 Rev.2 Copyright Code Red Technologies Inc. 2009 Page 1 of 18 1 OVERVIEW 3 1.1 LPC1768 Features 3 1.2 RDB1768 Evaluation Board Hardware 3 2 COMPONENTS 5 2.1

More information

ST1633. Datasheet. Capacitive Touch Screen Controller. Version /11/17

ST1633. Datasheet. Capacitive Touch Screen Controller. Version /11/17 Capacitive Touch Screen Controller Datasheet Version 1.6 2015/11/17 Note: Sitronix Technology Corp. reserves the right to change the contents in this document without prior notice. This is not a final

More information

Figure 1. Proper Method of Holding the ToolStick. Figure 2. Improper Method of Holding the ToolStick

Figure 1. Proper Method of Holding the ToolStick. Figure 2. Improper Method of Holding the ToolStick TOOLSTICK UNIVERSITY DAUGHTER CARD USER S GUIDE 1. Handling Recommendations To enable development, the ToolStick Base Adapter and daughter cards are distributed without any protective plastics. To prevent

More information

ARDUINO MICRO WITHOUT HEADERS Code: A000093

ARDUINO MICRO WITHOUT HEADERS Code: A000093 ARDUINO MICRO WITHOUT HEADERS Code: A000093 Arduino Micro is the smallest board of the family, easy to integrate it in everyday objects to make them interactive. The Micro is based on the ATmega32U4 microcontroller

More information

Growing Together Globally Serial Communication Design In Embedded System

Growing Together Globally Serial Communication Design In Embedded System Growing Together Globally Serial Communication Design In Embedded System Contents Serial communication introduction......... 01 The advantages of serial design......... 02 RS232 interface......... 04 RS422

More information

USB-to-I2C. Ultra Hardware User s Manual.

USB-to-I2C. Ultra Hardware User s Manual. USB-to-I2C Ultra Hardware User s Manual https://www.i2ctools.com/ Information provided in this document is solely for use with the USB-to-I2C Ultra product from SB Solutions, Inc. SB Solutions, Inc. reserves

More information

ARM Cortex-M4 Architecture and Instruction Set 1: Architecture Overview

ARM Cortex-M4 Architecture and Instruction Set 1: Architecture Overview ARM Cortex-M4 Architecture and Instruction Set 1: Architecture Overview M J Brockway January 25, 2016 UM10562 All information provided in this document is subject to legal disclaimers. NXP B.V. 2014. All

More information

FRDM-KL03Z User s Guide

FRDM-KL03Z User s Guide Freescale Semiconductor User s Guide Document Number: FRDMKL03ZUG Rev. 0, 7/2014 FRDM-KL03Z User s Guide 1 Overview The Freescale Freedom development platform is an evaluation and development tool ideal

More information

USER GUIDE. ATWINC1500 Xplained Pro. Preface

USER GUIDE. ATWINC1500 Xplained Pro. Preface USER GUIDE ATWINC1500 Xplained Pro Preface Atmel ATWINC1500 Xplained Pro is an extension board to the Atmel Xplained Pro evaluation platform. The extension board allows to evaluate the Atmel ATWINC1510/1500

More information

Raspberry Pi - I/O Interfaces

Raspberry Pi - I/O Interfaces ECE 1160/2160 Embedded Systems Design Raspberry Pi - I/O Interfaces Wei Gao ECE 1160/2160 Embedded Systems Design 1 I/O Interfaces Parallel I/O and Serial I/O Parallel I/O: multiple input/output simultaneously

More information

RN-174 WiFly Super Module

RN-174 WiFly Super Module RN- WiFly Super Module Features Evaluation board for the RN- module Supports chip antenna (RN--C), PCB trace antenna (RN--P), wire antenna (RN--W), and U.FL connector for an external antenna (RN--U) Ultra-low

More information

Datasheet. RS485 description The UART/RS485 physical layer gives support for UART communication and higher level Modbus protocol.

Datasheet. RS485 description The UART/RS485 physical layer gives support for UART communication and higher level Modbus protocol. Datasheet Main features Software Micro-kernel with scheduling, power and clock management Contiki OS Tickless design Drivers for peripherals Bluetooth 4.1 compliant low energy singlemode protocol stack

More information

LBAT90USB162 Atmel. LBAT90USB162 Development Board User s Manual

LBAT90USB162 Atmel. LBAT90USB162 Development Board User s Manual LBAT90USB162 Atmel AT90USB162 Development Board User s manual 1 1. INTRODUCTION Thank you for choosing the LBAT90USB162 Atmel AT90USB162 development board. This board is designed to give quick and cost-effective

More information

NanoDock DMC-3. Datasheet Daughter module carrier 4 daughterboard

NanoDock DMC-3. Datasheet Daughter module carrier 4 daughterboard NanoDock DMC-3 Datasheet Daughter module carrier 4 daughterboard 1 Table of Contents 1 TABLE OF CONTENTS... 2 2 OVERVIEW... 3 2.1 HIGHLIGHTED FEATURES... 3 2.2 GPS RECEIVER... 3 2.3 BLOCK DIAGRAM... 4

More information

The Information contained herein is subject to change without notice. Revisions may be issued regarding changes and/or additions.

The Information contained herein is subject to change without notice. Revisions may be issued regarding changes and/or additions. Pepper 43R TM Gumstix, Inc. shall have no liability of any kind, express or implied, arising out of the use of the Information in this document, including direct, indirect, special or consequential damages.

More information

The industrial technology is rapidly moving towards ARM based solutions. Keeping this in mind, we are providing a Embedded ARM Training Suite.

The industrial technology is rapidly moving towards ARM based solutions. Keeping this in mind, we are providing a Embedded ARM Training Suite. EMBEDDED ARM TRAINING SUITE ARM SUITE INCLUDES ARM 7 TRAINER KIT COMPILER AND DEBUGGER THROUGH JTAG INTERFACE PROJECT DEVELOPMENT SOLUTION FOR ARM 7 e-linux LAB FOR ARM 9 TRAINING PROGRAM INTRODUCTION

More information

Mega128-Net Mega128-Net Mega128 AVR Boot Loader Mega128-Net

Mega128-Net Mega128-Net Mega128 AVR Boot Loader Mega128-Net Mega128-Net Development Board Progressive Resources LLC 4105 Vincennes Road Indianapolis, IN 46268 (317) 471-1577 (317) 471-1580 FAX http://www.prllc.com GENERAL The Mega128-Net development board is designed

More information