AVR Training Board-I. VLSI Design Lab., Konkuk Univ. LSI Design Lab

Transcription

1 AVR Training Board-I V., Konkuk Univ. Tae Pyeong Kim

2 What is microcontroller A microcontroller is a small, low-cost computeron-a-chip which usually includes: An 8 or 16 bit microprocessor (CPU). A small amount of RAM. Programmable ROM and/or flash memory. Parallel and/or serial I/O. Timers and signal generators. Analog to Digital (A/D) and/or Digital to Analog (D/A) conversion. 2

3 Basics of microcontroller Examples: Motorola s 68HC11, 68HC12, AMD 29K, Zilog s Z8, Z80, Intel s 8052, Microchip s PIC Low-power, embedded versions of desktop CPUs: e.g Intel s

4 Microcontrollers Intel 8051 ARM Atmel AVR 8/32-bit architecture Freescale CF (32-bit), Freescale S08(8-bit), 68HC11(8-bit) Hitachi H8, Hitachi SuperH MIPS (32-bit PIC32) NEC V850 PIC (8-bit PIC16, PIC18, 16-bit dspic33 / PIC24) PowerPC ISE PSoC (Programmable System-on-Chip) Rabbit 2000 TI MSP430 (16-bit) Toshiba TLCS-870 Zilog ez8, ez80 4

5 Atmel AVR Microcontroller The AVR is a Modified Harvard architecture 8-bit RISC single chip microcontroller which was developed by Atmel in The AVR was one of the first microcontroller families to use on-chip flash memory for program storage, as opposed to One-Time Programmable ROM, EPROM, or EEPROM used by other microcontrollers at the time. Families of AVR tinyavr the ATtiny series megaavr the ATmega series XMEGA the ATxmega series Application specific AVR 5

6 8-bit AVR ATmega128 Microcontroller High-performance, Low-power AVR 8-bit Microcontroller Advanced RISC Architecture 133 Powerful Instructions Most Single Clock Cycle Execution 32 x 8 General Purpose Working Registers + Peripheral Control Registers Fully Static Operation Up to 16 MIPS Throughput at 16 MHz On-chip 2-cycle Multiplier Nonvolatile Program and Data Memories 128K Bytes of In-System Reprogrammable Flash Endurance: 10,000 Write/Erase Cycles Optional Boot Code Section with Independent Lock Bits In-System Programming by On-chip Boot Program True Read-While-Write Operation 4K Bytes EEPROM Endurance: 100,000 Write/Erase Cycles 4K Bytes Internal SRAM Up to 64K Bytes Optional External Memory Space Programming Lock for Software Security SPI Interface for In-System Programming Special Microcontroller Features Power-on Reset and Programmable Brown-out Detection Internal Calibrated RC Oscillator External and Internal Interrupt Sources Six Sleep Modes: Idle, ADC Noise Reduction, Power-save, Power-down, Standby, and Extended Standby Software Selectable Clock Frequency ATmega103 Compatibility Mode Selected by a Fuse Global Pull-up Disable 6 JTAG (IEEE std Compliant) Interface Boundary-scan Capabilities According to the JTAG Standard Extensive On-chip Debug Support Programming of Flash, EEPROM, Fuses and Lock Bits through the JTAG Interface Peripheral Features Two 8-bit Timer/Counters with Separate Prescalers and Compare Modes Two Expanded 16-bit Timer/Counters with Separate Prescaler, Compare Mode and Capture Mode Real Time Counter with Separate Oscillator Two 8-bit PWM Channels 6 PWM Channels with Programmable Resolution from 2 to 16 Bits Output Compare Modulator 8-channel, 10-bit ADC 8 Single-ended Channels 7 Differential Channels 2 Differential Channels with Programmable Gain at 1x, 10x, or 200x Byte-oriented Two-wire Serial Interface Dual Programmable Serial USARTs Master/Slave SPI Serial Interface Programmable Watchdog Timer with On-chip Oscillator On-chip Analog Comparator I/O and Packages 53 Programmable I/O Lines 64-lead TQFP and 64-pad QFN/MLF Operating Voltages V for ATmega128L V for ATmega128 Speed Grades 0-8 MHz for ATmega128L 0-16 MHz for ATmega128

7 Atmega128 - Pinout Pinout of Atmega128 7

8 Atmega128 - Block Diagram Block Diagram 8

9 Atmega128 - Pin function (1) Port A(PA7 PA0) 8-bit bi-direction I/O port with internal pull-up registers Output buffers have symmetrical drive characteristics with both high sing and source capability Tri-stated when a reset condition becomes active Port B(PB7-PB0) 8-bit bi-direction I/O port with internal pull-up registers Output buffers have symmetrical drive characteristics with both high sing and source capability Tri-stated when a reset condition becomes active Port C(PC7-PC0) - In Atmega103 compatibility mode, PortC is output only and C pins are not tri-stated when a reset condition becomes active Port D,E 8-bit bi-direction I/O port with internal pull-up registers Output buffers have symmetrical drive characteristics with both high sing and source capability Tri-stated when a reset condition becomes active 9

10 Atmega128 - Pin function (2) Port F(PF7-PF0) A/D converter input Can use as an 8 bit bi-direction I/O port, if A/D Converter is not used Serve the fuction of the JTAG interface. Port G(PG4-PG0) 5-bit bi-direction I/O port with internal pull-up registers Output buffers have symmetrical drive characteristics with both high sing and source capability Tri-stated when a reset condition becomes active 10

11 Atmega128 - Pin function (3) /PEN (Program Enable) Pin number : 1 For SP1 Serial Programming mode and is internally pulled high Holding this pin low during a Power-on Reset AREF (analog reference pin ) Pin number : 62 Analog reference pin for the A/C Converter /AVCC Pin number : 64 Supply voltage pin for PORT F and A/D converter RST (Reset) Pin number : 20 Master reset XTAL1, XTAL2 Pin number : 23,24 Oscillator input 11

12 ATmega128 Training Board RS-232 FND AVR LED SWITCH 12

13 Training board spec. 8-bit CPU optimized for control application 133 Powerful Instruction-Most Single Clock Cycle Execution 32x8 General Purpose Working Register+Peripheral control R 128K Bytes of Self-programmable Flash program memory Full duplex UART USB support On-chip clock oscillator IR_SENSOR 4 segment 13

14 Training board - operating frequency OSC (Oscillator) 연결방법 Machine Cycle (M/C) 1 M/C = 6 state (S1~s6) = 12 clock period 1 state = 2 phase (P1, P2) 1 M/C 동안에 2 ALE 신호발생 실습보드 MHz Crystal 사용 14

15 System Development Environment 하이퍼터미널프로그램 USB 모니터프로그램 15 AVR Training Board

16 I/O Ports of AVR All AVR ports have true Read-Modify-Write functionality when used as general digital I/O ports. The pin driver is strong enough to drive LED displays directly The ports are bi-directional I/O ports with optional internal pull-ups

17 General Digital I/O of AVR 17 17

18 Configuring the Pin Each port pin consists of three Register bits: DDxn, PORTxn, and PINxn

19 Register Summery for I/O Ports 19 19

20 Register Description for I/O Ports Port A Port B 20 20

21 Register Description for I/O Ports cont. Port C Port D 21 21

22 Register Description for I/O Ports cont. Port E Port F 22 22

23 Register Description for I/O Ports cont. Port G 23 23

24 Alternate Port Functions Most port pins have alternate functions in addition to being general digital I/Os. Port A Pins Alternate Functions Port B Pins Alternate Functions 24 24

25 Alternate Port Functions cont. Port C Pins Alternate Functions Port D Pins Alternate Functions Port E Pins Alternate Functions Port F Pins Alternate Functions Port G Pins Alternate Functions 25 25

26 LED Test Program 1 LED On 0 LED Off 26

27 LED Test Program 27

28 Appendix Schematic of Training Board 28

29 실험 #1 실험 1 : LED 를아래와같이점등하도록한다. LED1 LED2 LED3 LED4 1 초 2 초 LED1 LED2 LED3 LED4

30 실험 #2 실험 2 : LED 를아래와같이점등하도록한다. LED1 LED2 LED3 LED4 LED1 LED2 LED3 LED4 LED1 LED2 LED3 LED4 LED1 LED2 LED3 LED4 LED1 LED2 LED3 LED4 LED1 LED2 LED3 LED4

31 실험 #3 실험 3 : LED 를아래와같이점등하도록한다. SW8 을눌렀을때, Shift( 정방향 ) SW7 을눌렀을때, Shift( 역방향 ) 스위치를누를때마다부저동작 When SW8 is pressed When SW8 is pressed When SW8 is pressed LED1 LED2 LED3 LED4 LED1 LED2 LED3 LED4 LED1 LED2 LED3 LED4 When SW7 is pressed When SW7 is pressed When SW7 is pressed LED1 LED2 LED3 LED4 LED1 LED2 LED3 LED4 LED1 LED2 LED3 LED4