Basic Computer Organization and Design Part 2/3
|
|
|
- Nancy Helena Osborne
- 6 years ago
- Views:
Transcription
1 Basic Computer Organization and Design Part 2/3 Adapted by Dr. Adel Ammar Computer Organization
2 Basic Computer Instructions Basic Computer Instruction Format Memory-Reference Instructions (OP-code = 000 ~ 110) I Opcode Address Register-Reference Instructions (OP-code = 111, I = 0) Register operation Input-Output Instructions (OP-code =111, I = 1) I/O operation Computer Organization 2
3 Basic Computer Instructions Hex Code Symbol I = 0 I = 1 Description AND 0xxx 8xxx AND memory word to AC ADD 1xxx 9xxx Add memory word to AC LDA 2xxx Axxx Load AC from memory STA 3xxx Bxxx Store content of AC into memory BUN 4xxx Cxxx Branch unconditionally BSA 5xxx Dxxx Branch and save return address ISZ 6xxx Exxx Increment and skip if zero CLA 7800 Clear AC CLE 7400 Clear E CMA 7200 Complement AC CME 7100 Complement E CIR 7080 Circulate right AC and E CIL 7040 Circulate left AC and E INC 7020 Increment AC SPA 7010 Skip next instr. if AC is positive SNA 7008 Skip next instr. if AC is negative SZA 7004 Skip next instr. if AC is zero SZE 7002 Skip next instr. if E is zero HLT 7001 Halt computer INP F800 Input character to AC OUT F400 Output character from AC SKI F200 Skip on input flag SKO F100 Skip on output flag ION F080 Interrupt on IOF F040 Interrupt off Computer Organization 3
4 Instruction Set Completeness A computer should have a set of instructions so that the user can construct machine language programs to evaluate any function that is known to be computable. Instruction Types Functional Instructions Arithmetic, logic, and shift instructions ADD, CMA, INC, CIR, CIL, AND, CLA Transfer Instructions Data transfers between the main memory and the processor registers LDA, STA Control Instructions Program sequencing and control BUN, BSA, ISZ Input/Output Instructions Input and output INP, OUT Computer Organization 4
5 Control Unit Control unit (CU) of a processor translates from machine instructions to the control signals for the microoperations that implement them Control units are implemented in one of two ways Hardwired Control CU is made up of sequential and combinational circuits to generate the control signals Microprogrammed Control A control memory on the processor contains microprograms that activate the necessary control signals We will consider a hardwired implementation of the control unit for the Basic Computer Computer Organization 5
6 Timing and Control Control unit of Basic Computer Instruction register (IR) Other inputs 3 x 8 decoder I D 0 D 7 Combinational Control logic Control signals T 15 T x 16 decoder 4-bit sequence counter (SC) Increment (INR) Clear (CLR) Clock Computer Organization 6
7 Timing Signals Generated by 4-bit sequence counter (SC) and 4 16 decoder The SC can be incremented or cleared. Clock T0 T1 T0 T1 T2 T3 T4 T0 Example: T0, T1, T2, T3, T4, T0, T1,... Assume: At time T4, SC is cleared to 0 if decoder output D3 is active. D3T4: SC 0 T2 T3 T4 D3 CLR SC Computer Organization 7
8 Instruction Cycle In Basic Computer, a machine instruction is executed in the following cycle: 1. Fetch an instruction from memory 2. Decode the instruction 3. Read the effective address from memory if the instruction has an indirect address 4. Execute the instruction After an instruction is executed, the cycle starts again at step 1, for the next instruction Note: Every different processor has its own (different) instruction cycle Computer Organization 8
9 Fetch and Decode T0: AR PC (S 0 S 1 S 2 =010, T0=1) T1: IR M [AR], PC PC + 1 (S0S1S2=111, T1=1) T2: D0,..., D7 Decode IR(12-14), AR IR(0-11), I IR(15) T1 T0 S 2 S 1 Bus Memory unit Read Address S 0 7 AR 1 LD PC 2 INR IR 5 LD Common bus Clock Computer Organization 9
10 D7 IT3: AR M[AR] D7 I T3: Nothing D7I T3: Execute a register-reference instr. D7IT3: Execute an input-output instr. Determine the Type of Instruction Start SC 0 AR PC T0 IR M[AR], PC PC + 1 Decode Opcode in IR(12-14), AR IR(0-11), I IR(15) T1 T2 (Register or I/O) = 1 D7 = 0 (Memory-reference) (I/O) = 1 = 0 (register) (indirect) = 1 I I = 0 (direct) Execute input-output instruction SC 0 T3 T3 T3 T3 Execute AR M[AR] Nothing register-reference instruction SC 0 Execute memory-reference instruction SC 0 T4 Computer Organization 10
11 Register Reference Instructions Register Reference Instructions are identified when D7 = 1, I = 0 Register Ref. Instr. is specified in b0 ~ b11 of IR Execution starts with timing signal T3 Computer Organization 11
12 Register Reference Instructions r = D7 I T3 => Register Reference Instruction Bi = IR(i), i=0,1,2,...,11 r: SC 0 CLA rb 11 : AC 0 CLE rb 10 : E 0 CMA rb 9 : AC AC CME rb 8 : E E CIR rb 7 : AC shr AC, AC(15) E, E AC(0) CIL rb 6 : AC shl AC, AC(0) E, E AC(15) INC rb 5 : AC AC + 1 SPA rb 4 : if (AC(15) = 0) then (PC PC+1) SNA rb 3 : if (AC(15) = 1) then (PC PC+1) SZA rb 2 : if (AC = 0) then (PC PC+1) SZE rb 1 : if (E = 0) then (PC PC+1) HLT rb 0 : S 0 (S is a start-stop flip-flop) Computer Organization 12
13 Memory Reference Instructions Symbol Operation Decoder Symbolic Description AND D 0 AC AC M[AR] ADD D 1 AC AC + M[AR], E C out LDA D 2 AC M[AR] STA D 3 M[AR] AC BUN D 4 PC AR BSA D 5 M[AR] PC, PC AR + 1 ISZ D 6 M[AR] M[AR] + 1, if M[AR] + 1 = 0 then PC PC+1 The effective address of the instruction is in AR and was placed there during timing signal T2 when I = 0, or during timing signal T3 when I = 1 Memory cycle is assumed to be short enough to complete in a CPU cycle The execution of MR instruction starts with T4 Computer Organization 13
14 Memory Reference Instructions AND to AC D0T4: DR M[AR] Read operand D0T5: AC AC DR, SC 0 AND with AC ADD to AC D1T4: DR M[AR] Read operand D1T5: AC AC + DR, E Cout, SC 0 Add to AC and store carry in E LDA: Load to AC D2T4: DR M[AR] D2T5: AC DR, SC 0 STA: Store AC D3T4: M[AR] AC, SC 0 BUN: Branch Unconditionally D4T4: PC AR, SC 0 BSA: Branch and Save Return Address M[AR] PC, PC AR + 1 BSA: D5T4: M[AR] PC, AR AR + 1 D5T5: PC AR, SC 0 ISZ: Increment and Skip-if-Zero D6T4: DR M[AR] D6T5: DR DR + 1 D6T6: M[AR] DR, if (DR = 0) then (PC PC + 1), SC 0 Computer Organization 14
15 Memory Reference Instructions Memory, PC, AR at time T BSA 135 PC = 21 Next instruction Memory, PC after execution 20 0 BSA Next instruction AR = Subroutine PC = 136 Subroutine 1 BUN BUN 135 Memory Memory BSA: Branch and Save Return Address M[AR] PC, PC AR + 1 BSA: D5T4: M[AR] PC, AR AR + 1 D5T5: PC AR, SC 0 Computer Organization 15
16 Flowchart for Memory Reference Instructions Memory-reference instruction AND ADD LDA STA D 0 T 4 D 1 T 4 D 2 T 4 D 3 T 4 DR M[AR] DR M[AR] DR M[AR] M[AR] AC SC 0 D 0 T 5 D 1 T 5 D 2 T 5 AC AC DR AC AC + DR AC DR SC 0 E Cout SC 0 SC 0 BUN BSA ISZ PC AR SC 0 D T 4 4 D 5 T 4 D 6 T 4 M[AR] PC DR M[AR] AR AR + 1 D 5 T 5 D 6 T 5 PC AR DR DR + 1 SC 0 D 6 T 6 M[AR] DR If (DR = 0) then (PC PC + 1) SC 0 Computer Organization 16
17 Input/Output and Interrupt Input-Output Configuration INPR Input register - 8 bits OUTR Output register - 8 bits FGI Input flag - 1 bit FGO Output flag - 1 bit IEN Interrupt enable - 1 bit Input-output terminal Printer Keyboard Serial communication interface Receiver interface Transmitter interface Computer registers and flip-flops OUTR AC INPR FGO FGI Serial Communications Path Parallel Communications Path The terminal sends and receives serial information The serial info. from the keyboard is shifted into INPR The serial info. for the printer is stored in the OUTR INPR and OUTR communicate with the terminal serially and with the AC in parallel. The flags are needed to synchronize the timing difference between I/O device and the computer Computer Organization 17
18 Program Controlled Data Transfer CPU: /* Input, Initially FGI=0 */ loop: If FGI = 0 goto loop AC INPR, FGI 0 /* Output, Initially FGO=1 */ loop: If FGO = 0 goto loop OUTR AC, FGO 0 yes yes FGI=0 Start Input FGI 0 FGI=0 no AC INPR More Character END no Computer Organization 18
19 Program Controlled Data Transfer I/O Device: /* Input */ loop: If FGI = 1 goto loop INPR new data, FGI 1 /* Output */ loop: If FGO = 1 goto loop consume OUTR, FGO 1 yes yes FGO=1 Start Output AC Data FGO=0 OUTR AC FGO 0 More Character END no no Computer Organization 19
20 Input/Output Instructions D 7 IT 3 = p IR(i) = B i, i = 6,, 11 p: SC 0 Clear SC INP pb 11 : AC(0-7) INPR, FGI 0 Input char. to AC OUT pb 10 : OUTR AC(0-7), FGO 0 Output char. from AC SKI pb 9 : if(fgi = 1) then (PC PC + 1) Skip on input flag SKO pb 8 : if(fgo = 1) then (PC PC + 1) Skip on output flag ION pb 7 : IEN 1 Interrupt enable on IOF pb 6 : IEN 0 Interrupt enable off Computer Organization 20
21 Program Controlled Input/Output Program-controlled I/O Continuous CPU involvement I/O takes valuable CPU time CPU slowed down to I/O speed Simple Least hardware Input LOOP, SKI DEV BUN LOOP INP DEV Output LOOP, LDA DATA LOP, SKO DEV BUN LOP OUT DEV Computer Organization 21
UNIT:2 BASIC COMPUTER ORGANIZATION AND DESIGN
1 UNIT:2 BASIC COMPUTER ORGANIZATION AND DESIGN BASIC COMPUTER ORGANIZATION AND DESIGN 2.1 Instruction Codes 2.2 Computer Registers AC or Accumulator, Data Register or DR, the AR or Address Register, program
Computer Organization (Autonomous)
Computer Organization (Autonomous) UNIT II Sections - A & D Prepared by Anil Kumar Prathipati, Asst. Prof., Dept. of CSE. SYLLABUS Basic Computer Organization and Design: Instruction codes Stored Program
BASIC COMPUTER ORGANIZATION AND DESIGN
1 BASIC COMPUTER ORGANIZATION AND DESIGN Instruction Codes Computer Registers Computer Instructions Timing and Control Instruction Cycle Memory Reference Instructions Input-Output and Interrupt Complete
BASIC COMPUTER ORGANIZATION AND DESIGN
1 BASIC COMPUTER ORGANIZATION AND DESIGN Instruction Codes Computer Registers Computer Instructions Timing and Control Instruction Cycle Memory Reference Instructions Input-Output and Interrupt Complete
BASIC COMPUTER ORGANIZATION AND DESIGN
BASIC COMPUTER ORGANIZATION AND DESIGN Instruction Codes Computer Registers Computer Instructions Timing and Control Instruction Cycle Memory Reference Instructions Input-Output and Interrupt Complete
Basic Computer Organization - Designing your first computer. Acknowledgment: Most of the slides are adapted from Prof. Hyunsoo Yoon s slides.
Basic Computer Organization - Designing your first computer Acknowledgment: Most of the slides are adapted from Prof. Hyunsoo Yoon s slides. 1 This week- BASIC COMPUTER ORGANIZATION AND DESIGN Instruction
CHAPTER 5 Basic Organization and Design Outline Instruction Codes Computer Registers Computer Instructions Timing and Control Instruction Cycle
CS 224: Computer Organization S.KHABET CHAPTER 5 Basic Organization and Design Outline Instruction Codes Computer Registers Computer Instructions Timing and Control Instruction Cycle Memory Reference Instructions
5-1 Instruction Codes
Chapter 5: Lo ai Tawalbeh Basic Computer Organization and Design 5-1 Instruction Codes The Internal organization of a digital system is defined by the sequence of microoperations it performs on data stored
Computer Architecture and Organization: L06: Instruction Cycle
Computer Architecture and Organization: L06: Instruction Cycle By: A. H. Abdul Hafez Abdul.hafez@hku.edu.tr, ah.abdulhafez@gmail.com 1 Outlines 1. Fetch and decode 2. Determine the Type of Instruction
COMPUTER ORGANIZATION
COMPUTER ORGANIZATION INDEX UNIT-II PPT SLIDES Srl. No. Module as per Session planner Lecture No. PPT Slide No. 1. Register Transfer language 2. Register Transfer Bus and memory transfers 3. Arithmetic
Chapter 5. Computer Architecture Organization and Design. Computer System Architecture Database Lab, SANGJI University
Chapter 5. Computer Architecture Organization and Design Computer System Architecture Database Lab, SANGJI University Computer Architecture Organization and Design Instruction Codes Computer Registers
Computer Organization and Design
CSE211 Computer Organization and Design Lecture : 3 Tutorial: 1 Practical: 0 Credit: 4 KIDS Labs 1 Unit 1 : Basics of Digital Electronics Introduction Logic Gates Flip Flops Decoder Encoder Multiplexers
csitnepal Unit 3 Basic Computer Organization and Design
Unit 3 Basic Computer Organization and Design Introduction We introduce here a basic computer whose operation can be specified by the resister transfer statements. Internal organization of the computer
CHAPTER SIX BASIC COMPUTER ORGANIZATION AND DESIGN
CHAPTER SIX BASIC COMPUTER ORGANIZATION AND DESIGN 6.1. Instruction Codes The organization of a digital computer defined by: 1. The set of registers it contains and their function. 2. The set of instructions
Unit II Basic Computer Organization
1. Define the term. Internal Organization-The internal organization of a digital system is defined by the sequence of microoperations it performs on data stored in its registers. Program- A program is
Computer Architecture
http://www.bsccsit.com/ Computer Architecture CSC. 201 Third Semester Prepared By: Arjun Singh Saud Special thanks to Mr. Arjun Singh Saud for providing this valuable note! Chapter 1 Data representation
Programming Level A.R. Hurson Department of Computer Science Missouri University of Science & Technology Rolla, Missouri
Programming Level A.R. Hurson Department of Computer Science Missouri University of Science & Technology Rolla, Missouri 65409 hurson@mst.edu A.R. Hurson 1 Programming Level Computer: A computer with a
Midterm Examination # 2 Wednesday, March 18, Duration of examination: 75 minutes
Page 1 of 8 School of Computer Science 60-265-01 Computer Architecture and Digital Design Winter 2009 Midterm Examination # 2 Wednesday, March 18, 2009 Student Name: First Name Family Name Student ID Number:
Blog -
. Instruction Codes Every different processor type has its own design (different registers, buses, microoperations, machine instructions, etc) Modern processor is a very complex device It contains Many
Computer Organization and Architecture
Computer Organization and Architecture Dr Binu P Chacko Associate Professor Department of Computer Science Prajyoti Niketan College, Pudukad, THRISSUR Instruction Codes Computer organization is defined
Introduction. Machine Language. Assembly Language. Assembler. Program Loops. Programming Arithmetic and Logic Operations.
Computer System AA rc hh ii tec ture( 66 )) PROGRAMMING THE BASIC COMPUTER Introduction Machine Language Assembly Language Assembler Program Loops Programming Arithmetic and Logic Operations Subroutines
Computer architecture Assignment 3
Computer architecture Assignment 3 1- An instruction at address 14E in the basic computer has I=0, an operation code of the AND instruction, and an address part equal to 109(all numbers are in hexadecimal).
C.P.U Organization. Memory Unit. Central Processing Unit (C.P.U) Input-Output Processor (IOP) Figure (1) Digital Computer Block Diagram
C.P.U Organization 1.1 Introduction A computer system is sometimes subdivided into two functional entities "Hardware" and "Software". The H/W of the computer consists of all the electronic components and
Effective Approach for Teaching Computer System Architecture
Effective Approach for Teaching Computer System Architecture K. M. Hasam 1, Akhlaq A Khan 2, M. Saleem 3, M Riaz Moghal 3, asir Mahmood 4, M. Adnan 5, Tanveer Akhtar 6 1,3 Department of Electrical Engineering,
CHAPTER SEVEN PROGRAMMING THE BASIC COMPUTER
CHAPTER SEVEN 71 Introduction PROGRAMMING THE BASIC COMPUTER A computer system as it was mentioned before in chapter 1, it is subdivided into two functional parts: 1 Hardware, which consists of all physical
COMPUTER ARCHITECTURE AND DIGITAL DESIGN
SPECIAL MAKEUP - FINAL EXAMINATION COMPUTER ARCHITECTURE AND DIGITAL DESIGN 03-60-265-01 S C H O O L O F C O M P U T E R S C I E N C E - U N I V E R S I T Y O F W I N D S O R Fall 2008 Last Name: First
Darshan Institute of Engineering & Technology for Diploma Studies Unit - 1
Darshan Institute of Engineering & Technology for Diploma Studies Unit - 1 1. Draw and explain 4 bit binary arithmetic or adder circuit diagram. A binary parallel adder is digital function that produces
Faculty of Engineering Systems & Biomedical Dept. First Year Cairo University Sheet 6 Computer I
aculty of Engineering Systems & Biomedical Dept. irst Year Cairo University Sheet 6 Computer I 1. Choose rue or alse for each of the following statements a) In a direct addressing mode instruction, the
Computer Architecture
Computer Architecture Lecture 1: Digital logic circuits The digital computer is a digital system that performs various computational tasks. Digital computers use the binary number system, which has two
COMPUTER ARCHITECTURE AND ORGANIZATION Register Transfer and Micro-operations 1. Introduction A digital system is an interconnection of digital
Register Transfer and Micro-operations 1. Introduction A digital system is an interconnection of digital hardware modules that accomplish a specific information-processing task. Digital systems vary in
Chapter 16. Control Unit Operation. Yonsei University
Chapter 16 Control Unit Operation Contents Micro-Operation Control of the Processor Hardwired Implementation 16-2 Micro-Operations Micro-Operations Micro refers to the fact that each step is very simple
جامعة بنها - كمية العموم قسم الرياضيات المستوي الرابع )علوم حاسب( يوم االمتحان: االحد تاريخ االمتحان: 1024 / 21 / 12 المادة :
جامعة بنها - كمية العموم قسم الرياضيات المستوي الرابع )علوم حاسب( يوم االمتحان: االحد تاريخ االمتحان: 1024 / 21 / 12 م المادة : بنية الحاسب )124 رس( الممتحن: د/ مصعب عبد الحميد محمد حسان مدرس بقسم الرياضيات
THE MICROPROCESSOR Von Neumann s Architecture Model
THE ICROPROCESSOR Von Neumann s Architecture odel Input/Output unit Provides instructions and data emory unit Stores both instructions and data Arithmetic and logic unit Processes everything Control unit
There are four registers involved in the fetch cycle: MAR, MBR, PC, and IR.
CS 320 Ch. 20 The Control Unit Instructions are broken down into fetch, indirect, execute, and interrupt cycles. Each of these cycles, in turn, can be broken down into microoperations where a microoperation
Micro-Operations. execution of a sequence of steps, i.e., cycles
Micro-Operations Instruction execution execution of a sequence of steps, i.e., cycles Fetch, Indirect, Execute & Interrupt cycles Cycle - a sequence of micro-operations Micro-operations data transfer between
REGISTER TRANSFER LANGUAGE
REGISTER TRANSFER LANGUAGE The operations executed on the data stored in the registers are called micro operations. Classifications of micro operations Register transfer micro operations Arithmetic micro
Register Transfer and Micro-operations
Register Transfer Language Register Transfer Bus Memory Transfer Micro-operations Some Application of Logic Micro Operations Register Transfer and Micro-operations Learning Objectives After reading this
M. Sc (CS) (II Semester) Examination, Subject: Computer System Architecture Paper Code: M.Sc-CS-203. Time: Three Hours] [Maximum Marks: 60
![M. Sc (CS) (II Semester) Examination, Subject: Computer System Architecture Paper Code: M.Sc-CS-203. Time: Three Hours] [Maximum Marks: 60](/thumbs/87/96339673.jpg "M. Sc (CS) (II Semester) Examination, Subject: Computer System Architecture Paper Code: M.Sc-CS-203. Time: Three Hours] [Maximum Marks: 60")
M. Sc (CS) (II Semester) Examination, 2012-13 Subject: Computer System Architecture Paper Code: M.Sc-CS-203 Time: Three Hours] [Maximum Marks: 60 Note: Question Number 1 is compulsory. Answer any four
William Stallings Computer Organization and Architecture
William Stallings Computer Organization and Architecture Chapter 16 Control Unit Operations Rev. 3.2 (2009-10) by Enrico Nardelli 16-1 Execution of the Instruction Cycle It has many elementary phases,
Credit Based Choice Based Curriculum for. Bachelor of Computer Applications (BCA) Programme 2016 Onwards
Credit Based Choice Based Curriculum for Bachelor of Computer Applications (BCA) Programme 216 Onwards S. No. Subject Code Name of the Subject Core Courses Credit Details Credit Hours L T P 1. BCA-1611CC
Lecture1: introduction. Outline: History overview Central processing unite Register set Special purpose address registers Datapath Control unit
Lecture1: introduction Outline: History overview Central processing unite Register set Special purpose address registers Datapath Control unit 1 1. History overview Computer systems have conventionally
SCRAM Introduction. Philipp Koehn. 19 February 2018
SCRAM Introduction Philipp Koehn 19 February 2018 This eek 1 Fully work through a computer circuit assembly code Simple but Complete Random Access Machine (SCRAM) every instruction is 8 bit 4 bit for op-code:
Class Notes. Dr.C.N.Zhang. Department of Computer Science. University of Regina. Regina, SK, Canada, S4S 0A2
Class Notes CS400 Part VI Dr.C.N.Zhang Department of Computer Science University of Regina Regina, SK, Canada, S4S 0A2 C. N. Zhang, CS400 83 VI. CENTRAL PROCESSING UNIT 1 Set 1.1 Addressing Modes and Formats
Assembly Language Programming of 8085
Assembly Language Programming of 8085 Topics 1. Introduction 2. Programming model of 8085 3. Instruction set of 8085 4. Example Programs 5. Addressing modes of 8085 6. Instruction & Data Formats of 8085
UNIT-III REGISTER TRANSFER LANGUAGE AND DESIGN OF CONTROL UNIT
UNIT-III 1 KNREDDY UNIT-III REGISTER TRANSFER LANGUAGE AND DESIGN OF CONTROL UNIT Register Transfer: Register Transfer Language Register Transfer Bus and Memory Transfers Arithmetic Micro operations Logic
CHAPTER 8: Central Processing Unit (CPU)
CS 224: Computer Organization S.KHABET CHAPTER 8: Central Processing Unit (CPU) Outline Introduction General Register Organization Stack Organization Instruction Formats Addressing Modes 1 Major Components
Computer Organization II CMSC 3833 Lecture 33
Term MARIE Definition Machine Architecture that is Really Intuitive and Easy 4.8.1 The Architecture Figure s Architecture Characteristics: Binary, two s complement Stored program, fixed word length Word
INSTRUCTION SET OF 8085
INSTRUCTION SET OF 8085 Instruction Set of 8085 An instruction is a binary pattern designed inside a microprocessor to perform a specific function. The entire group of instructions that a microprocessor
REGISTER TRANSFER AND MICROOPERATIONS
1 REGISTER TRANSFER AND MICROOPERATIONS Register Transfer Language Register Transfer Bus and Memory Transfers Arithmetic Microoperations Logic Microoperations Shift Microoperations Arithmetic Logic Shift
For Example: P: LOAD 5 R0. The command given here is used to load a data 5 to the register R0.
Register Transfer Language Computers are the electronic devices which have several sets of digital hardware which are inter connected to exchange data. Digital hardware comprises of VLSI Chips which are
Roll No TCS 402/TIT 402
Roll No TCS 402/TIT 402 Mid Term Examination March 2016 B.Tech (IV Semester) Computer Organization Time: Two (2) Hrs. Maximum Marks: 60 NOTE: (i) (ii) (iii) (iv) This question paper contains three questions
2 MARKS Q&A 1 KNREDDY UNIT-I
2 MARKS Q&A 1 KNREDDY UNIT-I 1. What is bus; list the different types of buses with its function. A group of lines that serves as a connecting path for several devices is called a bus; TYPES: ADDRESS BUS,
Control Unit Implementation Hardwired Memory
Chapter 7: Microprogrammed nit mplementation Hardwired nstruction code Sequence Counter Combinational Logic Circuits signals Microprogrammed nstruction code CAR: Register CDR: Data Register Next Generator
Computer Organization (Autonomous)
Computer Organization (Autonomous) UNIT I Sections - A & D Prepared by Anil Kumar Prathipati, Asst. Prof., Dept. of CSE. SYLLABUS Introduction: Types of Computers, Functional units of Basic Computer (Block
REGISTER TRANSFER AND MICROOPERATIONS
REGISTER TRANSFER AND MICROOPERATIONS Register Transfer Language Register Transfer Bus and Memory Transfers Arithmetic Microoperations Logic Microoperations Shift Microoperations Arithmetic Logic Shift
COA. Prepared By: Dhaval R. Patel Page 1. Q.1 Define MBR.
Q.1 Define MBR. MBR( Memory buffer register) A Memory Buffer Register (MBR) is the register in a computers processor that stores the data being transferred to and from the devices It allowing the processor
Control unit. Input/output devices provide a means for us to make use of a computer system. Computer System. Computer.
Lecture 6: I/O and Control I/O operations Control unit Microprogramming Zebo Peng, IDA, LiTH 1 Input/Output Devices Input/output devices provide a means for us to make use of a computer system. Computer
UNIT - V MEMORY P.VIDYA SAGAR ( ASSOCIATE PROFESSOR) Department of Electronics and Communication Engineering, VBIT
UNIT - V MEMORY P.VIDYA SAGAR ( ASSOCIATE PROFESSOR) contents Memory: Introduction, Random-Access memory, Memory decoding, ROM, Programmable Logic Array, Programmable Array Logic, Sequential programmable
Digital System Design Using Verilog. - Processing Unit Design
Digital System Design Using Verilog - Processing Unit Design 1.1 CPU BASICS A typical CPU has three major components: (1) Register set, (2) Arithmetic logic unit (ALU), and (3) Control unit (CU) The register
COMPUTER ORGANIZATION AND ARCHITECTURE
Page 1 1. Which register store the address of next instruction to be executed? A) PC B) AC C) SP D) NONE 2. How many bits are required to address the 128 words of memory? A) 7 B) 8 C) 9 D) NONE 3. is the
Combinational and sequential circuits (learned in Chapters 1 and 2) can be used to create simple digital systems.
REGISTER TRANSFER AND MICROOPERATIONS Register Transfer Language Register Transfer Bus and Memory Transfers Arithmetic Microoperations Logic Microoperations Shift Microoperations Arithmetic Logic Shift
Blog - https://anilkumarprathipati.wordpress.com/
Control Memory 1. Introduction The function of the control unit in a digital computer is to initiate sequences of microoperations. When the control signals are generated by hardware using conventional
MAHALAKSHMI ENGINEERING COLLEGE TIRUCHIRAPALLI UNIT I THE 8085 & 8086 MICROPROCESSORS. PART A (2 Marks)
MAHALAKSHMI ENGINEERING COLLEGE TIRUCHIRAPALLI-621213. UNIT I THE 8085 & 8086 MICROPROCESSORS PART A (2 Marks) 1. Give the significance of SIM and RIM instruction available in 8085. [NOV/DEC 2006] Instruction
PSIM: Processor SIMulator (version 4.2)
PSIM: Processor SIMulator (version 4.2) by Charles E. Stroud, Professor Dept. of Electrical & Computer Engineering Auburn University July 23, 2003 ABSTRACT A simulator for a basic stored program computer
Mini-Computer PDP-8 ISA Simulator Design and Verification
Mini-Computer PDP-8 ISA Simulator Design and Verification Students Authors: Rajath Mavathur Basavaraj Ranjith Kumar M Supervised By: Dr. Elarabi Why ISA simulator Simulation at the ISA -Instruction Set
General purpose registers These are memory units within the CPU designed to hold temporary data.
Von Neumann Architecture Single processor is used Each instruction in a program follows a linear sequence of fetch decode execute cycle Program and data are held in same main memory Stored program Concept
Magdy Saeb, Samy Salamah Arab Academy for Science, Technology & Maritime Transport School of Engineering, Computer Department Alexandria, Egypt
AN IMPLEMENTATION OF A PIPELINED ENCRYPTION MULTI-PROCESSING UNIT UTILIZING VHDL AND FIELD PROGRAMMABLE GATE ARRAYS Magdy Saeb, Samy Salamah Arab Academy for Science, Technology & Maritime Transport School
DC57 COMPUTER ORGANIZATION JUNE 2013
Q2 (a) How do various factors like Hardware design, Instruction set, Compiler related to the performance of a computer? The most important measure of a computer is how quickly it can execute programs.
Chapter 3 : Control Unit
3.1 Control Memory Chapter 3 Control Unit The function of the control unit in a digital computer is to initiate sequences of microoperations. When the control signals are generated by hardware using conventional
Module 5 - CPU Design
Module 5 - CPU Design Lecture 1 - Introduction to CPU The operation or task that must perform by CPU is: Fetch Instruction: The CPU reads an instruction from memory. Interpret Instruction: The instruction
Computer Architecture Programming the Basic Computer
4. The Execution of the EXCHANGE Instruction The EXCHANGE routine reads the operand from the effective address and places it in DR. The contents of DR and AC are interchanged in the third microinstruction.
MICROPROGRAMMED CONTROL
MICROPROGRAMMED CONTROL Hardwired Control Unit: When the control signals are generated by hardware using conventional logic design techniques, the control unit is said to be hardwired. Micro programmed
TYPES OF INTERRUPTS: -
There are 3 types of interrupts. TYPES OF INTERRUPTS: - External Interrupts. Internal Interrupts. Software interrupts. Hardware Interrupts (1) External interrupts come from I/O devices, from a timing device
STRUCTURE OF DESKTOP COMPUTERS
Page no: 1 UNIT 1 STRUCTURE OF DESKTOP COMPUTERS The desktop computers are the computers which are usually found on a home or office desk. They consist of processing unit, storage unit, visual display
CHAPTER 4: Register Transfer Language and Microoperations
CS 224: Computer Organization S.KHABET CHAPTER 4: Register Transfer Language and Microoperations Outline Register Transfer Language Register Transfer Bus and Memory Transfers Arithmetic Microoperations
Part A Questions 1. What is an ISP? ISP stands for Instruction Set Processor. This unit is simply called as processor which executes machine instruction and coordinates the activities of other units..
IA-32 architecture. PDP8/e architecture Arithmetic. IA-32 architecture (cont)
PDP8/e architecture Arithmetic CS207, Fall 2004 September 27, 2004 1 IA-32 architecture 20-year development cycle (!) First version: 8086 architecture (16-bit), 1978 Moved to 32-bit in 1985 (80386) Now:
(2) Explain the addressing mode of OR What do you mean by addressing mode? Explain diff. addressing mode for 8085 with examples.
(1) Explain instruction format and Opcode format of 8085 μp with example. OR With help of examples, explain the formation of opcodes of 8085 OR What is an instruction? List type of instruction based on
CPU Design John D. Carpinelli, All Rights Reserved 1
CPU Design 1997 John D. Carpinelli, All Rights Reserved 1 Outline Register organization ALU design Stacks Instruction formats and types Addressing modes 1997 John D. Carpinelli, All Rights Reserved 2 We
IAS Computer. Instructions
IAS Computer Instructions The IAS computer was designed in the 1940's and built in the early 1950's by John von Neumann at the Princeton Institute for Advanced Studies. It can arguably be called the father
Advanced Parallel Architecture Lesson 3. Annalisa Massini /2015
Advanced Parallel Architecture Lesson 3 Annalisa Massini - 2014/2015 Von Neumann Architecture 2 Summary of the traditional computer architecture: Von Neumann architecture http://williamstallings.com/coa/coa7e.html
Fig: Computer memory with Program, data, and Stack. Blog - NEC (Autonomous) 1
Central Processing Unit 1. Stack Organization A useful feature that is included in the CPU of most computers is a stack or last in, first out (LIFO) list. A stack is a storage device that stores information
Introduction to Computers - Chapter 4
Introduction to Computers - Chapter 4 Since the invention of the transistor and the first digital computer of the 1940s, computers have been increasing in complexity and performance; however, their overall
Chapter 4. MARIE: An Introduction to a Simple Computer. Chapter 4 Objectives. 4.1 Introduction. 4.2 CPU Basics
Chapter 4 Objectives Learn the components common to every modern computer system. Chapter 4 MARIE: An Introduction to a Simple Computer Be able to explain how each component contributes to program execution.
CC312: Computer Organization
CC312: Computer Organization Dr. Ahmed Abou EL-Farag Dr. Marwa El-Shenawy 1 Chapter 4 MARIE: An Introduction to a Simple Computer Chapter 4 Objectives Learn the components common to every modern computer
Final Exam Review. b) Using only algebra, prove or disprove the following:
EE 254 Final Exam Review 1. The final exam is open book and open notes. It will be made up of problems similar to those on the previous 3 hour exams. For review, be sure that you can work all of the problems
Outcomes. Lecture 13 - Introduction to the Central Processing Unit (CPU) Central Processing UNIT (CPU) or Processor
Lecture 13 - Introduction to the Central Processing Unit (CPU) Outcomes What is a CPU? How are instructions prepared by the CPU before execution? What registers and operations are involved in this preparation
EE 3170 Microcontroller Applications
EE 3170 Microcontroller Applications Lecture 4 : Processors, Computers, and Controllers - 1.2 (reading assignment), 1.3-1.5 Based on slides for ECE3170 by Profs. Kieckhafer, Davis, Tan, and Cischke Outline
Chapter 4. MARIE: An Introduction to a Simple Computer
Chapter 4 MARIE: An Introduction to a Simple Computer Chapter 4 Objectives Learn the components common to every modern computer system. Be able to explain how each component contributes to program execution.
MICROPROGRAMMED CONTROL
1 MICROPROGRAMMED CONTROL Control Memory Sequencing Microinstructions Microprogram Example Design of Control nit Microinstruction Format Nanostorage and Nanoprogram 2 Implementation of Control nit COMPARISON
MICROPROGRAMMED CONTROL
1 MICROPROGRAMMED CONTROL Control Memory Sequencing Microinstructions Microprogram Example Design of Control nit Microinstruction Format Nanostorage and Nanoprogram External input (IR) Next address generator
Chapter 4 Topics. Comp. Sys. Design & Architecture 2 nd Edition Prentice Hall, Mark Franklin,S06
Chapter 4 Topics The Design Process A 1-bus Microarchitecture for SRC Data Path Implementation Logic Design for the 1-bus SRC The Control Unit The 2- and 3-bus Processor Designs The Machine Reset Process
CPU ARCHITECTURE. QUESTION 1 Explain how the width of the data bus and system clock speed affect the performance of a computer system.
CPU ARCHITECTURE QUESTION 1 Explain how the width of the data bus and system clock speed affect the performance of a computer system. ANSWER 1 Data Bus Width the width of the data bus determines the number
INTELLIGENCE PLUS CHARACTER - THAT IS THE GOAL OF TRUE EDUCATION UNIT-I
UNIT-I 1. List and explain the functional units of a computer with a neat diagram 2. Explain the computer levels of programming languages 3. a) Explain about instruction formats b) Evaluate the arithmetic
MARIE: An Introduction to a Simple Computer
MARIE: An Introduction to a Simple Computer Outline Learn the components common to every modern computer system. Be able to explain how each component contributes to program execution. Understand a simple
Microcomputer Architecture and Programming
IUST-EE (Chapter 1) Microcomputer Architecture and Programming 1 Outline Basic Blocks of Microcomputer Typical Microcomputer Architecture The Single-Chip Microprocessor Microprocessor vs. Microcontroller
Instruction Set Instruction set of 8085 can be classified in following groups: Data Transfer Instructions These instructions can perform data transfer operations between Registers of 8085 e.g. MOV 8085
CPU Structure and Function
Computer Architecture Computer Architecture Prof. Dr. Nizamettin AYDIN naydin@yildiz.edu.tr nizamettinaydin@gmail.com http://www.yildiz.edu.tr/~naydin CPU Structure and Function 1 2 CPU Structure Registers
8085 INSTRUCTION SET INSTRUCTION DETAILS
8085 INSTRUCTION SET INSTRUCTION DETAILS DATA TRANSFER INSTRUCTIONS MOV Rd, Rs Copy from source to destination This instruction copies the contents of the source register Rs into the destination register
session 7. Datapath Design
General Objective: Determine the hardware requirement of a digital computer based on its instruction set. Specific Objectives: Describe the general concepts in designing the data path of a digital computer