16-port 1000BASE-X/100Base-FX-SFP + 8-port Combo + 2-port 10 Gigabit XFP Interface Ethernet LSU1GP24TXEA0

Transcription

1 16-port 1000BASE-X/100Base-FX-SFP + 8-port Combo + 2-port 10 Gigabit XFP Interface Ethernet Card LSU1GP24TXEA0 1 Card identifier The mark LSU1GP24TXEA0 is printed at the upper right corner of the front panel, and is used to identify the card. 2 Specifications Table 1 LSU1GP24TXEA0 specifications Item Connector Port quantity Interface speed Cable and maximum Power consumption Applied to LSU1GP24TXEA0 LC RJ-45 Sixteen 1000Base-X-SFP/100Base-FX-SFP Ethernet ports Eight combo interfaces (Each composed of a 10/100/1000Base-T Gigabit Ethernet port and an SFP port, which cannot work simultaneously.) Two 10GBASE-R-XFP Ethernet ports 1000Base-X-SFP/100Base-FX-SFP Ethernet ports: 1000/100 Mbps 10/100/1000Base-T Gigabit Ethernet ports: 10/100/1000 Mbps (half/full duplex) 10GBASE-R-XFP Ethernet ports: 10 Gbps 1000Base-X-SFP/100Base-FX-SFP Ethernet ports: See Table 2. 10/100/1000Base-T Gigabit Ethernet ports: Category-5 twisted pair; maximum : 100 m ( ft) 10GBASE-R-XFP Ethernet ports: See Table 3 54 W to 95 W Switch Series NOTE: The ports numbered 17 through 24 on the card are combo interfaces. Each combo interface comprises a fiber port (1000Base-X-SFP/100Base-FX-SFP port) and a copper port (10/100/1000Base-T Ethernet port), which share the same interface view. The two ports of a combo interface cannot work simultaneously. When you use the combo enable { copper fiber } command in interface view to enable a port, the other port is automatically disabled. The 1000Base-X-SFP/100Base-FX-SFP port of a combo interface does not support transceiver module JD089B. For supported SFP modules, see the following table. i

2 Table 2 SFP module specifications Maximum JD089B HP X120 1G SFP RJ45 T Category-5 twisted pair 100 m ( ft) JD118B HP X120 1G SFP LC SX m ( ft) m ( ft) m ( ft) m ( ft) 9/ km (6.21 JD119B HP X120 1G SFP LC LX m ( ft) JD061A JD062A JD063B HP X125 1G SFP LC LH nm HP X120 1G SFP LC LH nm HP X125 1G SFP LC LH m ( ft) / km ( km ( km (43.50 JD103A HP X120 1G SFP LC LH km (62.14 JD098B JD099B HP X120 1G SFP LC BX 10-U HP X120 1G SFP LC BX 10-D The two modu les must be used in pairs. TX: 1310nm RX: 1490nm TX: 1490nm RX: 1310nm 9/ km (6.21 9/ km (6.21 JD113A JD114A JD115A LH LH LH / km ( / km ( / km (43.50 ii

3 JD116A JD109A JD110A JD111A JD112A LH LH LH LH LH Maximum / km ( km ( / km ( / km ( / km (43.50 JD102B HP X M SFP LC FX km (1.24 JD120B JD090A JD091A LX LH40 LH / km ( / km (24.86 JD100A JD101A HP X M SFP LC BX 10-U HP X M SFP LC BX 10-D The two modu les must be used in pairs. TX: 1310 RX: 1550 TX: 1550 RX: / km (9.32 9/ km (9.32 For supported XFP modules, see the following table. iii

4 Table 3 Specifications of XFP modules Max JD117B HP X130 10G XFP LC SR m ( ft) m( ft) m( ft) m ( ft) m (85.3 ft) JD108B HP X130 10G XFP LC LR / km (6.21 JD121A HP X135 10G XFP LC ER 40 km (24.86 JD107A HP X130 10G XFP LC ZR JG226A 80km nm DWDM /125 JG227A 80km nm DWDM /125 JG228A 80km nm DWDM /125 JG229A 80km nm DWDM /125 JG230A 80km nm DWDM /125 JG231A 80km nm DWDM /125 JG232A 80km nm DWDM /125 JG233A 80km nm DWDM /125 NOTE: The 9/125μm single-mode fibers used by modules JG226A through JG233A should conform to ITU-T G.655, and those used by other modules should conform to ITU-T G.652. iv

5 3 Obtaining more information For card installation, see the HP Switch Series Installation Guide. For software upgrade, see the HP Switch Series Software Upgrade Guide. To find related documents, browse to the Manuals page of the HP Business Support Center website: Copyright 2012 Hewlett-Packard Development Company, L.P. The information in this document is subject to change without notice v