S8 user guide. Origen

Transcription

1 S8 user guide Origen

2 S8 user guide Thank you for purchasing this Origen ae htpc enclosure. We recommend that you read this user guide thoroughly before installation. Origen ae has rapidly grown to be one of the worlds leading HTPC enclosure manufacturers since its inception in We were one of the first companies with the vision to produce high end htpc enclosures that harmonise with mainstream audio visual equipment, allowing the pc to leave the office and fit effortlessly into the living room environment. We are driven by the passion to produce exceptional products that push technical and aesthetic boundaries to new levels. For more information on all of our products, visit Origen ae is not responsible for any damages due to external causes, including but not limited to, improper use, problems with electrical power, accident, neglect, alteration, repair, improper installation or improper testing. SVUG.V1/05.2 Copyright 2013 Origen ae Technology All rights reserved

3 index S8 S8 overview Opening the case ODD cage removal Optical disk drive installation Metal sticker fitting instructions Optical drive bezel installation HDD cage removal Hard drive installation USB 3.0 ports connection Max height CPU cooler IR310 cable reference diagram Installing IR Software

4 S8 overview These are the main features and controls of the S8 htpc enclosure Power button Power LED ring IR receiver window Top panel Optical disk drive vezel USB 3.0 ports ODD eject button Optical disk drive brackets IR310 IR controller fixing point Hard disk drive brackets Top panel fixing screw 1 x 60mm low db intake fan

5 1 2 Opening the case Remove the thumb screws as indicated. Carefully raise the panel as shown (about 30mm is enough) and pull out to remove. Reverse the procedure to replace. DO NOT force upwards as this could cause damage to the top panel. ODD cage removal Remove left / right 4 fixing screws completely from the chassis. ODD bracket Optical disk drive Optical disc drive installation Separate the existing plastic drive bezel from your ODD. The disc tray should be ejected and requires some upward force to the bezel. Put your ODD in left / right ODD bracket and fix screws like picture. After fixing screws, assemble ODD bracket to chassis. Secure all fixing screws and check the eject button function. 5

6 Metal sticker fitting instructions The drive format icon should also be fitted to the bezel before installation. The metal sticker sheet supplied has Blu-ray, HD-DVD or DVD icons, depending on the format being used. Ensure the bezel is free from dirt of grease. Peel and fold back the yellow backing sheet, revealing only the part you wish to use. Carefully position the icon as central as possible, then apply even pressure over the entire area. Peel off the plastic film (and unused icons) to reveal you handy work! TOP TOP foam tape Optical disk drive bezel installation The aluminum ODD bezel matches the finish of the case. The installation procedure requires that the plastic drive bezel that comes fitted to your drive, be removed prior to installation. Check that the drive has been aligned correctly and that the tray can eject and close freely. Peel the back off the adhesive foam strip on the rear of the aluminium bezel. Fold a cardboard spacer around each end of the bezel, holding your thumb against the flaps as shown. With the tray closed, position inside the drive opening and press firmly against the front of the tray to ensure good adhesion. Eject the tray to remove the spacers. 6

7 HDD cage removal Remove left / right 4 fixing screws completely from the chassis. Hard drive installation Put your HDD in Left / right HDD bracket and fix screws as shown. * The specification of ODD bracket and HDD bracket is same. USB 3.0 connection The S8 is allowed to use two USB 3.0 port by connecting to mainboard as shown. Refer to your mainboard user guide if the mainboard supports USB 3.0 socket. Max height CPU cooler The maximum size of CPU cooler is 5mm as shown picture. Max height CPU cooler 5mm

8 IR310 cable reference diagram This is IR310 module and cable connection. Ensure all cables connection as diagram. Contact for special purchase of Ir310. *Remind that wrong cable connection might be damaged to your PC components. Check/ensure cable connection correctly as below. To Motherboard Power on/off Header From Chassis Power Switch Part list 1. IR310 module 2. S-FRIO-P3 3. S-IUSB-C2 4. S-ATXS-C1 5. S-IRIO-C1 6. S-IPSW-C1. S-ATXI-C1 To USB Header 8

9 Installing ir software Download the IR310 installation software from our web-site. Read this notice before installation. - The USB (S-IUSB-C2) cable must be connected to USB header pins. (See page 8) - The 5V standby cable (S-ATXS-C1) cable must be connected. (See page 8) 1. Download the VF310 installation software from our web-site or as attached following link Click Next. 2. Release the downloaded file in the location which is suitable. 3. Installation the imonsetup in folder.. Select the programs. (imon is essential and imedian HD is unessential) 4. After opening a read the concern, Click Start Setup to continue. 8. Click finish to next setup now. 9. Reboot computer. 10. Please select the MCE or imon pad remote from the option page. 5. Select the language. Installation is now completed. Thank you. 9

10 Origen Global HQ #209 Baeksan B/D 63-2 Hengsin-Dong Dukyang-Gu Goyang City Gyounggi-Do South Korea Website ae.com