1 HP Ersatzteile für DesignJet 1055CM

Transcription

1 HP Ersatzteile für DesignJet 0CM Air Pressurization System, Ink Supply Stat C07-00* C Ink Supply Station (ISS) - Has four slots for ink cartridges Air pressurization system (APS) - Includes pump, valve, pressure sensor, and APS housing - Installed under the ink supply station Carriage Assembly, Cutter Assembly, Trailing Cable +9 (0) 7 / 78-0

2 HP Ersatzteile für DesignJet 0CM C07-97 C07-00 C07-08 Carriage assembly kit - Includes carriage, carriage height tool cutter assembly, and line sensor - Does not include cable Cutter assembly kit - Includes mounting hardware - Installed under carriage assembly Carriage trailing cable kit - Includes cable, trailing cable clip, nye oil, cover cap, trailing cable ferrite, ferrite holder Carriage Motor, Carriage Belt, Encoder, Rollfeed C07-09 C07-09 C C C C07-08* C07-0* C07-0* C07-07* Carriage motor - Includes pulley Tensioner assembly - Includes pulley assembly, pulley spring, wedge, cutter actuator arm, and tensioner housing Cutter actuator arm Carriage drive belt kit - Includes belt and oil Encoder strip Left roll feed module - Installed at top of left leg Right roll feed module - Installed at top of right leg Right roll feed brake - Installed in right roll feed module Left roll feed brake - Installed in left roll feed module +9 (0) 7 / 78-0

3 HP Ersatzteile für DesignJet 0CM Center Guide and Media Sensor C07-00 C07-090* Center guide and media sensor (Guide is the full width of the plotter) - Mounts near the front platen and center platen assemblies Media sensor - Media sensor - Installed on the center guide Clutch Assembly C07-0 Clutch assembly - Includes lever, gears, a spring, and the shaft that they ride on +9 (0) 7 / 78-0

4 HP Ersatzteile für DesignJet 0CM Drive Roller Gear and Miscellaneous ARSS Parts C07-09* C07-0* Paper drive roller assembly - Includes drive roller, roller gear, and roller bracket Automatic roll sheet switch (ARSS) parts kit - ARSS torsion spring, ARSS axle gear, ARSS switch lever - Installed on left side of print chassis Drive Roller, Drive Roller Guide, Media Guide Strip C07-09* C07-0 C07-09 Paper drive roller assembly - Includes drive roller, roller gear, and roller bracket Drive roller guide (Guide is the full width of the plotter) - Includes the drive roller guide and media guide strip - Mounts in front of the drive roller Media guide strip - Installed between the drive roller and the drive roller guide +9 (0) 7 / 78-0

5 HP Ersatzteile für DesignJet 0CM Electronics Module and Plug-in Devices J-900 J-900* JA* J8-0* J7-00 J9-00* J79-0 C07-000* C07-07 C C C CA* CA* C8A* C07-99 C07-07 C07-07 C07-9* JetDirect 00N EIO internal print server 0Base-T, 0BASE-, and LocalTalk LAN interface board - Has one RJ-, BNC, and 8-pin DIN connector - (JA) JetDirect 00N EIO internal print server token ring LAN interface board - Has one RJ- and DB-9 connector - JetDirect 00N EIO Internal Print Server (Token Ring) LAN Interface Board - Has One RJ- and DB-9 Connectors (JA) JetDirect 00N internal print server (0Base-T and 00Base-TX) LAN interface board - Plugs into peripheral EIO slot - The standard interface for the printer External JetDirect 70X LAN interface module - Interfaces a parallel printer to an ethernet 0Base-T (RJ-) LAN JetDirect 0N token ring LAN interface board - DB-9 and RJ- connectors JetDirect 0N internal print server (0Base-T and 00Base-TX) LAN interface board - Plugs into peripheral EIO slot - Has a RJ- connector - Comes with software on CD-ROM and manual - Replacement for JA Fast Ethernet LAN interface board JetDirect 0n internal print server - 0BaseT and 00BaseTX LAN interface board - Plugs into peripheral EIO slot - Has an RJ- connector -.GB hard drive (DesignJet EIO Font/Print Job Storage) DIMM cover - Covers the DIMM sockets in the electronics module MB EDO (Extended Data Output) DRAM DIMM memory module MB EDO (Extended Data Output) DRAM DIMM memory module MB EDO (Extended Data Output) DRAM DIMM memory module MB EDO (Extended Data Output) DRAM DIMM - For DesignJet 000 series printers MB EDO (Extended Data Output) DRAM DIMM - For DesignJet 000 series printers MB EDO (Extended Data Output) DRAM DIMM - For DesignJet 000 series printers Firmware DIMM (Revision A.0.) - Mounts in the electronics module - RTL version Right rear cover - Covers the end of the electronics module that is not near the DIMM cover Left rear cover kit - Covers electronics module near the DIMM cover - Includes ferrite and clip Electronics module - Contains power supply, main logic board and cooling fan +9 (0) 7 / 78-0

6 HP Ersatzteile für DesignJet 0CM Left Cover, Ink Tubes System, Window C07-07 C07-07 C07-0 C07-0 C C Left cover - Covers the ink tube system and has a door to access the ink cartridges Left trim - On the left arc Lift-up viewing window Ink Tube System - Includes setup printheads, ink collector, carrier clip, nye oil, ink supply station housing foam Nameplate - DesignJet 00C Adope PostScript label Pinch Assembly +9 (0) 7 / 78-0

7 7 HP Ersatzteile für DesignJet 0CM C * Pinch assembly - Includes pinch cam, pinch rollers and springs Printer Stand C07-08 C07-08 C07-08 C C07-08 Printer stand tray - Mounted between the feet of printer Foot assembly (includes casters) - Mounts to the bottom of the stand legs (two used) Leg assembly - Side support for the printer - Does NOT include the foot assembly - (Two used) Media bin - Between printer stand legs Cross-brace - Brace that connects and supports the two stand legs +9 (0) 7 / 78-0

8 8 HP Ersatzteile für DesignJet 0CM Rear Covers C07-08 C07-09 C07-08* C07-08* C C Top cover - Covers the top of the print mechanism (Not the window) Back cover - Includes blank serial number label Rear platen assembly Tail deflectors - (Three used) Back EMC cover - Installs between the rear cover and the print mechanism Rear cover mounting bracket kit - Includes left and right brack Right Cover and Front Panel Assembly +9 (0) 7 / 78-0

9 9 HP Ersatzteile für DesignJet 0CM C07-0 C07-07* C07-07* C07-0 C07-0* C07-0 C07-0 C07-0* C07-0 C07-07 C07-08 C07-09 C07-00* Right cover - Includes front panel cable - Does not include front panel assembly or aerosol fan Right trim - On the right arc Front panel assembly - Includes front panel cable Front panel overlay (English) Front panel overlay (Korean) Front panel overlay (Taiwanese) Front panel overlay (German) Front panel overlay (French) Front panel overlay (Spanish) Front panel overlay (Italian) Front panel overlay (Japanese) Front panel overlay (Portuguese) Front panel overlay (Chinese) Service Station, Vacuum Fan, Paper Motor C80-00* C8-000* C8-009* C8-000* C C07-09* C07-00* C Black printhead cleaner - Installed in spittoon Cyan printhead cleaner - Installed in spittoon Magenta printhead cleaner - Installed in spitt Yellow printhead cleaner - Installed in spittoon Service station assembly - Includes drop detector assembly Vacuum/aerosol fan assembly - Includes the fan and air flow guide - Mounts on the right side of the printer chassis assembly Paper drive motor - Includes helical drive gear and mounting bracket - Installed on right side of printer chassis Drop detector (sensor) assembly - Includes spittoon foam - Installed in service station assembly +9 (0) 7 / 78-0

10 0 HP Ersatzteile für DesignJet 0CM Spindle and Paper Path Parts C07-0 C07-0 C07-00* C07-0 C07-0* C07-0* E/A0 rollfeed spindle assembly - Includes end caps - (C078A) Entry roller - Large, long roller at front of printer Automatic roll sheet switch (ARSS) assembly - Small, long roller and housing - Used to feed cut sheet media Handle for automatic roll sheet switch (ARSS) assembly - (Two used) Front platen assembly - Long, curved item without rollers - Includes platen and screws Center platen assembly - Includes overdrive rollers and screws +9 (0) 7 / 78-0

11 HP Ersatzteile für DesignJet 0CM Tubes Guide, Front Guide, Left and Right Arcs C07-09 C07-09 C07-09 C07-09 Tube guide assembly Front guide assembly (U-shaped) - Mounts in front of the tube guide assembly Right arc assembly - Right arc assembly - Structure installed between the right cover and the printer chassis Left arc assembly - Left arc assembly - Structure installed between the left cover and the printer chassis +9 (0) 7 / 78-0